MX53 has five UART ports.
Add support for the missing UART4 and UART5 ports.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It is not good to have cpu_name and to_version encoded into sdma
firmware name as variables. For example, there are three TOs of
imx51 soc, the sdma script never changes since TO1, which means
all three TOs of imx51 uses TO1 version of sdma script. But we
have to prepare three identical firmwares, sdma-imx51-to1.bin
sdma-imx51-to2.bin and sdma-imx51-to3.bin, to have the kernel
capable of running on all three TOs.
The patch removes cpu_name and to_version from sdma platform data,
and instead uses fw_name to pass the firmware name, so that we can
pass the TO version where it's relevant and skip it where only one
firmware exists.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The patch follows the implementation of gpio-mxc device registration
to break the concentrated imx-dma device registration into soc
specific setup function. Then we can avoid the churn of "#ifdef"
and the cpu_is_mx checking on such a long list, which makes no sense,
considering more soc supports need to be added and we need to support
single image for multiple socs in the long run.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There are several occurences where MXC_INTERNAL_IRQ is
assumed to be the start of the gpio interrupts. It was never
meant this way. Replace these with gpio_to_irq.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
This gets rid of per machine struct platform_device definitions and allows
to move the platform data and led definition to .init.rodata.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Instead of using gpio_request followed by gpio_direction_output use gpio_request_array
when requesting multiple pins.
Also fixed the location of the delay for the reset and make the BABBAGE_USB_PHY_RESET to toggle.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The USB PHY Reset GPIO can be configured in the same place as the other GPIOs.
While at it rename the pin as BABBAGE_USB_PHY_RESET to make clearer its purpose.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The clock from which the I2C timing is derived is the ipg_perclk not ipg_clk.
I2C bus frequency was lower by a factor of ~8 due to the clock divider
calculation being based on 66.5MHz IPG clock while the bus actually
uses 8MHz ipg_perclk.
Kernel version: 3.0.0-rc2 branch 'imx-for-next' of git://git.pengutronix.de/git/imx/linux-2.6
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The patch makes necessary changes on gpio-mxc as below to turn it
into an upstanding gpio driver.
* Add a list to save all mx2 ports references, so that
mx2_gpio_irq_handler can walk through all interrupt status
registers
* Use readl/writel to replace mach-specific accessors
__raw_readl/__raw_writel
* Change mxc_gpio_init into mxc_gpio_probe function
* Move "struct mxc_gpio_port" into gpio-mxc.c, as it needs not to
be public at all, and also make some other cleanup on
plat-mxc/include/mach/gpio.h at the same time
And the patch then migrates mach-imx and mach-mx5 to the updated
driver by adding corresponding platform devices.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The two SoCs have different PHYS_OFFSETs so it's not (yet) possible to
compile a single (working) kernel for these.
LAKML-Reference: 1302464943-20721-4-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The symbols in this choice should only be used to select between the
available machines that can be built into a single kernel. As these sets
(will) differ e.g. depending on ARM_PATCH_PHYS_VIRT and AUTO_ZRELADDR
letting them select other symbols makes the logic more complex and needs
to duplicate some things. So let the machines select the corresponding
symbols (indirectly via SOC_XYZ).
LAKML-Reference: 1302464943-20721-2-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There is no need for using a MX51-specific version of imx_add_gpio_keys.
Remove imx51_add_gpio_keys and use imx_add_gpio_keys instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
LAKML-Reference: 1302105926-20574-1-git-send-email-fabio.estevam@freescale.com
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Most machine files include "devices-imxXX.h" which in turn includes
<mach/devices-common.h>. The latter already includes many headers
that the machine files don't need to include again.
These were found by:
$ grep \#include arch/arm/plat-mxc/include/mach/devices-common.h > tmpfile
$ git grep -l 'devices-imx' arch/arm | xargs grep -f tmpfile -F
(but I kept linux/init.h, linux/kernel.h and linux/platform_device.h)
LAKML-Reference: 1298912674-15153-2-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Current code inside babbage_usbhub_reset uses gpio_direction_output with initial value of the GPIO and also sets
the GPIO value via gpio_set_value to the same level right after. This is not needed.
By using gpio_request_one it is possible to set the direction and initial value in one shot.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
LAKML-Reference: 1300377359-23212-2-git-send-email-fabio.estevam@freescale.com
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Having the silicon revision to appear on the boot log is a useful information.
MX31, MX35 and MX51 already show the silicon revision on boot.
Add support for displaying such information for MX53 as well.
Tested on a mx53loco board, where it shows:
CPU identified as i.MX53, silicon rev 2.0
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
LAKML-Reference: 1301068367-18937-1-git-send-email-fabio.estevam@freescale.com
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
MFD changes in 4ec1b54c ('mfd: mfd_cell is now implicitly available to
mc13xxx drivers') changed the mc13xxx_platform_data struct layout.
At the time all users were changed, but this driver was introduced in
another tree at the same time. This updates the mc13xxx_platform_data
user, fixing a build error.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Note that this relies on stuff currently in mfd's next tree, but this
is also a newer driver. I'm not sure which tree it should go through,
as it's a problem that shows up in next.
From: Andres Salomon <dilinger@queued.net>
MFD changes in c738892f cause the mc13xxx_platform_data struct
to change. This changes one more (new) user of it, fixing a build
error.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Implement code for MX51 that allows the SoC to enter WFI when
arch_idle is called.
This patch is also necessary for correctly suspending the system.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For MX51 SRPG, we need to turn on the GPC clock in order to set the
SRPG registers.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For MX50, the HW_ADADIG_DIGPROG register in the ANATOP module will
have the correct silicon revision:
Major Minor Description
0x50 0x0 TO1.0
0x50 0x1 TO1.1
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As there is a mx53_smd board in the kernel, using SMD_FEC_PHY_RST as the pin name can be misleading when used
on a MX53_EVK board.
Change the pin name to reflect the board name.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Current code inside mx53_evk_fec_reset uses gpio_direction_output with initial value of the GPIO and also sets
the GPIO value via gpio_set_value right after. This is not needed.
By using gpio_request_one it is possible to set the direction and initial value in one shot.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Current code inside babbage_fec_reset uses gpio_direction_output with initial value of the GPIO and also sets
the GPIO value via gpio_set_value to the same level right after. This is not needed.
By using gpio_request_one it is possible to set the direction and initial value in one shot.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Having the silicon revision to appear on the boot log is a useful information.
MX31 and MX35 already show the silicon revision on boot.
Add support for displaying such information for MX51 as well.
Tested on a MX51EVK, where it shows:
CPU identified as i.MX51, silicon rev 3.0
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move to SOC_SOC_IMX5X. Leave only places which prevent multi-soc
using ARCH_MX5X.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The boards are currently using otg_ulpi_create and mxc_ulpi_access_ops,
both are only present if CONFIG_USB_ULPI is set. To remove the need of
ifdefs in the board code introduce a imx_otg_ulpi_create functions
which expands to a static inline function if compiled without ulpi.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On mx53_evk board only RX/TX pins are used on UART3.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
