Set the GPMI CTRL1 GANGED_RDYBUSY bit so driver can sense the R/B signal
from all CS.
For the NAND chip MT29F64G08AFAAAWP, only the first chip detected
without the patch.
[ 3.764118] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x68
[ 3.770613] nand: Micron MT29F64G08AFAAAWP
[ 3.774752] nand: 4096 MiB, SLC, erase size: 1024 KiB, page size: 8192, OOB size: 448
[ 3.786421] Bad block table found at page 524160, version 0x01
[ 3.792730] Bad block table found at page 524032, version 0x01
After applying the patch
[ 3.764445] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x68
[ 3.770941] nand: Micron MT29F64G08AFAAAWP
[ 3.775080] nand: 4096 MiB, SLC, erase size: 1024 KiB, page size: 8192, OOB size: 448
[ 3.784390] nand: 2 chips detected
[ 3.790900] Bad block table found at page 524160, version 0x01
[ 3.796776] Bad block table found at page 1048448, version 0x01
Signed-off-by: Han Xu <han.xu@nxp.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201209035104.22679-2-han.xu@nxp.com
SDX55 uses QPIC version 2.0.0 IP for the NAND controller support.
In this version, DEV_CMD_* registers are moved to operational state,
hence CPU access in BAM mode is restricted. So, skip accessing these
registers and also use a different config for reading ONFI parameters.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201126085705.48399-3-manivannan.sadhasivam@linaro.org
Call clk_disable_unprepare(nfc->phase_rx) if the clk_set_rate() function
fails to avoid a resource leak.
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/X8ikVCnUsfTpffFB@mwanda
The retrieval of driver data via of_device_get_match_data() can make
the code simpler.
Use of_device_get_match_data() to simplify the code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201126030946.2058-1-festevam@gmail.com
This patch adds the new IP of Nand Flash Controller(NFC) support
on Intel's Lightning Mountain(LGM) SoC.
DMA is used for burst data transfer operation, also DMA HW supports
aligned 32bit memory address and aligned data access by default.
DMA burst of 8 supported. Data register used to support the read/write
operation from/to device.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201110012333.18647-3-vadivel.muruganx.ramuthevar@linux.intel.com
pm_runtime_get_sync() will increment pm usage at first and it
will resume the device later. If runtime of the device has
error or device is in inaccessible state(or other error state),
resume operation will fail. If we do not call put operation to
decrease the reference, it will result in reference leak in
the two functions(gpmi_init and gpmi_nfc_exec_op). Moreover,
this device cannot enter the idle state and always stay busy or
other non-idle state later. So we fixed it through adding
pm_runtime_put_noidle.
Fixes: 5bc6bb603b ("mtd: rawnand: gpmi: Fix suspend/resume problem")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201107110552.1568742-1-zhangqilong3@huawei.com
If an error happens in mtd_device_parse_register or mtd_device_register,
memory allocated for struct platram_info is leaked.
Make platram_probe() call platram_remove() on all error paths
after struct platram_info allocation to correctly free resources.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Baskov Evgeiny <baskov@ispras.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113160537.899-1-baskov@ispras.ru
struct mtd_info has a flag oops_panic_write which is set when the write
operation is issued via the panic_write() callback. That allows controller
drivers to distinguish the panic write from a regular write.
Replace the open coded 'in_interrupt() | oops_in_progress' checks with a
check for that flag. in_interrupt() is an unrealiable indicator anyway as
it covers all sorts of atomic contexts not only hard and soft interrupt
service routines.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: linux-mtd@lists.infradead.org
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113141422.2214771-1-bigeasy@linutronix.de
While working a bit on this driver I dropped the platform includes and
commented a few lines just to verify the correctness of my changes. It
appeared the following:
drivers/mtd/nand/raw/au1550nd.c: In function ‘au1550nd_waitrdy’:
drivers/mtd/nand/raw/au1550nd.c:130:3: error: implicit declaration of function ‘usleep_range’ [-Werror=implicit-function-declaration]
usleep_range(10, 100);
^~~~~~~~~~~~
drivers/mtd/nand/raw/au1550nd.c: In function ‘au1550nd_exec_instr’:
drivers/mtd/nand/raw/au1550nd.c:188:3: error: implicit declaration of function ‘ndelay’ [-Werror=implicit-function-declaration]
ndelay(instr->delay_ns);
^~~~~~
I think the delay.h header should be included in this file and not
come from one of its platform includes, so let's add it here.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113124021.32675-1-miquel.raynal@bootlin.com
The NAND ECC core is included in the generic NAND core when it is
compiled in.
Different software ECC engines drivers will select the NAND ECC core
and thus also have a dependency on the NAND core. Using a "depends on"
between the two leads to possible cases (not real cases, but created
by robots) where one is still unselected because of the "select does
not verifies depends on" game:
WARNING: unmet direct dependencies detected for MTD_NAND_ECC
Depends on [n]: MTD [=m] && MTD_NAND_CORE [=n]
Selected by [m]:
- MTD_NAND_ECC_SW_HAMMING [=y] && MTD [=m]
- MTD_NAND_ECC_SW_BCH [=y] && MTD [=m]
Fix this by using a select instead.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/linux-mtd/20201113123945.32592-1-miquel.raynal@bootlin.com
i.MX is a devicetree-only platform now and the existing platform data
support in this driver was only useful for old non-devicetree platforms.
Get rid of the platform data support since it is no longer used.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201110121908.19400-1-festevam@gmail.com
of_find_device_by_node() already takes a reference to the device, and
ingenic_ecc_release() will drop the reference. So, the get_device() in
ingenic_ecc_get() is redundand.
Fixes: 15de8c6efd0e("mtd: rawnand: ingenic: Separate top-level and SoC specific code")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201031105439.2304211-1-yukuai3@huawei.com
This code has been written in 2008 and is fine, but in order to keep
robots happy, I think it's time to change a little bit this code just
to clarify the different possible values of eccsize_mult. Indeed, this
variable may only take the value 1 or 2 because step_size, in the case
of the software Hamming ECC engine may only be 256 or 512. Depending
on the value of eccsize_mult, an extra rp17 variable is set, or not
and triggers the following warning:
smatch warnings:
ecc_sw_hamming_calculate() error: uninitialized symbol 'rp17'.
As highlighted by Dan Carpenter, if the only possible values for
eccsize_mult are 1 and 2, then the code is fine, but "it's hard to
tell just from looking".
So instead of shifting step_size, let's use a ternary condition to
assign to eccsize_mult the only two possible values and clarify the
driver's logic.
Now that the situation is clarified for humans, ensure rp17 is
initialized to 0 to keep compilers and robots silent as well.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201030172333.28390-1-miquel.raynal@bootlin.com
This patch enables NAND MDMA (MBUS DMA) mode for
the Allwinner SoCs A23/A33/H3.
The DMA transfer method gets sets now to MBUS DMA as default for
the sun8i-a23-nand-controller (till now DMA transfer was executed
via the shared DMA engine).
The main advantage is more bandwidth for the users of the shared DMA
engine and also that the MBUS DMA setup requires less configuration
effort. For example you don't need to define a dedicated DMA channel
in the device-tree any more.
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Manuel Dipolt <manuel.dipolt@robart.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/154840787.280672.1602517282173.JavaMail.zimbra@robart.cc
After each codeword NAND_FLASH_STATUS is read for possible operational
failures. But there is no DMA sync for CPU operation before reading it
and this leads to incorrect or older copy of DMA buffer in reg_read_buf.
This patch adds the DMA sync on reg_read_buf for CPU before reading it.
Fixes: 5bc36b2bf6 ("mtd: rawnand: qcom: check for operation errors in case of raw read")
Cc: stable@vger.kernel.org
Signed-off-by: Praveenkumar I <ipkumar@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1602230872-25616-1-git-send-email-ipkumar@codeaurora.org
Even if this is not supposed to happen, there is no reason to fail the
probe if it was explicitly requested to use no ECC engine at all (for
instance, during development). This condition is met by just
commenting out the error on the OOB free bytes count after the
assignation of an ECC engine if none was provided (any other situation
would error out much earlier anyway).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201001102014.20100-5-miquel.raynal@bootlin.com
Now that all the logic is available in the NAND core, let's use it
from the SPI-NAND core. Right now there is no functional change as the
default ECC engine for SPI-NANDs is set to 'on-die', but user can now
use software correction if they want to by just setting the right
properties in the DT.
Also note that the OOB layout handling is removed from the SPI-NAND
core as each ECC engine is supposed to handle it by it's own; users
should not be aware of that.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201001102014.20100-4-miquel.raynal@bootlin.com
Add the logic in the NAND core to find the right ECC engine depending
on the NAND chip requirements and the user desires. Right now, the
choice may be made between (more will come):
* software Hamming
* software BCH
* on-die (SPI-NAND devices only)
Once the ECC engine has been found, the ECC engine must be
configured.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201001102014.20100-2-miquel.raynal@bootlin.com
The SPI-NAND layer default is on-die ECC because until now it was the
only one supported. New SPI-NAND chip flavors might use something else
as ECC engine provider but this will always be the default if the user
does not choose explicitly something else.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200930154109.3922-6-miquel.raynal@bootlin.com
Make use of the existing functions taken from the SPI-NAND core to
instantiate an on-die ECC engine specific to the SPI-NAND core. The
next step will be to tweak the core to use this object instead of
calling the helpers directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200930154109.3922-4-miquel.raynal@bootlin.com
Prepare the creation of a SPI-NAND on-die ECC engine by gathering the
ECC-related code earlier enough in the core to avoid the need for
forward declarations.
The next step is to actually create that engine by implementing the
generic ECC interface.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200930154109.3922-3-miquel.raynal@bootlin.com
This code is meant to be reused by the SPI-NAND core. Now that the
driver has been cleaned and reorganized, use a generic ECC engine
object to store the driver's data instead of accessing members of the
nand_chip structure. This means adding proper init/cleanup helpers.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-17-miquel.raynal@bootlin.com
Prefix by ecc_sw_hamming_ the functions which should be internal only
but are exported for "raw" operations.
Prefix by nand_ecc_sw_hamming_ the other functions which will be used
in the context of the declaration of an Hamming proper ECC engine
object.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-16-miquel.raynal@bootlin.com
Some functions should never have been exported (the ones prefixed by
__*), in this case simply drop the documentation, we never want
anybody to use this function from the outside.
For the other functions, enhance the style.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-14-miquel.raynal@bootlin.com
The include file pretends being the header for "ECC algorithm", while
it is just the header for the Hamming implementation. Make this clear
by rewording the sentence.
Do the same with the module description.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-13-miquel.raynal@bootlin.com
nand_ecc_ctrl embeds a private pointer which only has a meaning in the
sunxi driver. This structure will soon be deprecated, but as this
field is actually not needed, let's just drop it.
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-11-miquel.raynal@bootlin.com
Let's continue introducing the generic ECC engine abstraction in the
NAND subsystem by instantiating a first ECC engine: the software
BCH one.
While at it, make a very tidy ecc_sw_bch_init() function and move all
the sanity checks and user input management in
nand_ecc_sw_bch_init_ctx(). This second helper will be called from the
raw RAND core.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-10-miquel.raynal@bootlin.com
Traditionally, Linux unlocks the whole flash because there are legacy
devices which has the write protection bits set by default at startup.
If you actually want to use the flash protection bits, eg. because there
is a read-only part for a bootloader, this automatic unlocking is
harmful. If there is no hardware write protection in place (usually
called WP#), a startup of the kernel just discards this protection.
I've gone through the datasheets of all the flashes (except the Intel
ones where I could not find any datasheet nor reference) which supports
the unlocking feature and looked how the sector protection was
implemented. The currently supported flashes can be divided into the
following two categories:
(1) block protection bits are non-volatile. Thus they keep their values
at reset and power-cycle
(2) flashes where these bits are volatile. After reset or power-cycle,
the whole memory array is protected.
(a) some devices needs a special "Global Unprotect" command, eg.
the Atmel AT25DF041A.
(b) some devices require to clear the BPn bits in the status
register.
Due to the reasons above, we do not want to clear the bits for flashes
which belong to category (1). Fortunately for us, only Atmel flashes
fall into category (2a). Implement the "Global Protect" and "Global
Unprotect" commands for these. For (2b) we can use normal block
protection locking scheme.
This patch adds a new flag to indicate the case (2). Only if we have
such a flash we unlock the whole flash array. To be backwards compatible
it also introduces a kernel configuration option which restores the
complete legacy behavior ("Disable write protection on any flashes").
Hopefully, this will clean up "unlock the entire flash for legacy
devices" once and for all.
For reference here are the actually commits which introduced the legacy
behavior (and extended the behavior to other chip manufacturers):
commit f80e521c91 ("mtd: m25p80: add support for the Intel/Numonyx {16,32,64}0S33B SPI flash chips")
commit ea60658a08 ("mtd: m25p80: disable SST software protection bits by default")
commit 7228982442 ("[MTD] m25p80: fix bug - ATmel spi flash fails to be copied to")
Actually, this might also fix handling of the Atmel AT25DF flashes,
because the original commit 7228982442 ("[MTD] m25p80: fix bug -
ATmel spi flash fails to be copied to") was writing a 0 to the status
register, which is a "Global Unprotect". This might not be the case in
the current code which only handles the block protection bits BP2, BP1
and BP0. Thus, it depends on the current contents of the status register
if this unlock actually corresponds to a "Global Unprotect" command. In
the worst case, the current code might leave the AT25DF flashes in a
write protected state.
The commit 191f5c2ed4 ("mtd: spi-nor: use 16-bit WRR command when QE
is set on spansion flashes") changed that behavior by just clearing BP2
to BP0 instead of writing a 0 to the status register.
Further, the commit 3e0930f109 ("mtd: spi-nor: Rework the disabling
of block write protection") expanded the unlock_all() feature to ANY
flash which supports locking.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-8-michael@walle.cc
These flashes have some weird BP bits mapping which aren't supported in
the current locking code. Just add a simple unlock op to unprotect the
entire flash array which is needed for legacy behavior.
Fixes: 3e0930f109 ("mtd: spi-nor: Rework the disabling of block write protection")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-7-michael@walle.cc
For the Atmel and SST parts this flag was already moved to individual
flash parts because it is considered bad esp. because newer flash chips
will automatically inherit the "has locking" support. While this won't
likely be the case for the Intel parts, we do it for consistency
reasons.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-6-michael@walle.cc
This is considered bad for the following reasons:
(1) We only support the block protection with BPn bits for write
protection. Not all SST parts support this.
(2) Newly added flash chip will automatically inherit the "has
locking" support and thus needs to explicitly tested. Better
be opt-in instead of opt-out.
(3) There are already supported flashes which doesn't support
the locking scheme. So I assume this wasn't properly tested
before adding that chip; which enforces my previous argument
that locking support should be an opt-in.
Remove the global flag and add individual flags to all flashes
which supports BP locking. In particular the following flashes
don't support the BP scheme:
- SST26VF016B
- SST26WF016B
- SST26VF064B
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-5-michael@walle.cc
This is considered bad for the following reasons:
(1) We only support the block protection with BPn bits for write
protection. Not all Atmel parts support this.
(2) Newly added flash chip will automatically inherit the "has
locking" support and thus needs to explicitly tested. Better
be opt-in instead of opt-out.
(3) There are already supported flashes which doesn't support
the locking scheme. So I assume this wasn't properly tested
before adding that chip; which enforces my previous argument
that locking support should be an opt-in.
Remove the global flag and add individual flags to all flashes which
supports BP locking. In particular the following flashes don't support
the BP scheme:
- AT26F004
- AT25SL321
- AT45DB081D
Please note, that some flashes which are marked as SPI_NOR_HAS_LOCK just
support Global Protection, i.e. not our supported block protection
locking scheme. This is to keep backwards compatibility with the
current "unlock all at boot" mechanism. In particular the following
flashes doesn't have BP bits:
- AT25DF041A
- AT25DF321
- AT25DF321A
- AT25DF641
- AT26DF081A
- AT26DF161A
- AT26DF321
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-4-michael@walle.cc
Just try to unlock the whole SPI-NOR flash array. Don't abort the
probing in case of an error. Justifications:
(1) For some boards, this just works because
spi_nor_write_16bit_sr_and_check() is broken and just checks the
second half of the 16bit. Once that will be fixed, SPI probe will
fail for boards which has hardware-write protected SPI-NOR flashes.
(2) Until now, hardware write-protection was the only viable solution
to use the block protection bits. This is because this very
function spi_nor_unlock_all() will be called unconditionally on
every linux boot. Therefore, this bits only makes sense in
combination with the hardware write-protection. If we would fail
the SPI probe on an error in spi_nor_unlock_all() we'd break
virtually all users of the block protection bits.
(3) We should try hard to keep the MTD working even if the flash might
not be writable/erasable.
Fixes: 3e0930f109 ("mtd: spi-nor: Rework the disabling of block write protection")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-3-michael@walle.cc
This flash part actually has 4 block protection bits.
Please note, that this patch is just based on information of the
datasheet of the datasheet and wasn't tested.
Fixes: 3e0930f109 ("mtd: spi-nor: Rework the disabling of block write protection")
Reported-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201203162959.29589-2-michael@walle.cc
The S28 flash family uses 2-bit ECC by default with each ECC block being
16 bytes. Under this scheme multi-pass programming to an ECC block is
not allowed. Set the writesize to make sure multi-pass programming is
not attempted on the flash.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201201102711.8727-4-p.yadav@ti.com
Some flashes like the Cypress S28 family use ECC. Under this ECC scheme,
multi-pass writes to an ECC block is not allowed. In other words, once
data is programmed to an ECC block, it can't be programmed again without
erasing it first.
Upper layers like file systems need to be given this information so they
do not cause error conditions on the flash by attempting multi-pass
programming. This can be done by setting 'writesize' in 'struct
mtd_info'.
Set the default to 1 but allow flashes to modify it in fixup hooks. If
more flashes show up with this constraint in the future it might be
worth it to add it to 'struct flash_info', but for now increasing its
size is not worth it.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201201102711.8727-3-p.yadav@ti.com
There are a few typos in comments in the SPI NOR framework; fix them.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201130152416.1283972-1-j.neuschaefer@gmx.net
Permit the user to specify the erase page size as a parameter.
This solves two problems:
- phram can access images made by mkfs.jffs2. mkfs.jffs2 won't
create images with erase sizes less than 8KiB; many architectures
define PAGE_SIZE as 4KiB.
- Allows more effective use of small capacity devices. JFFS2
needs somewhere between 2 and 5 empty pages for garbage collection;
and for an NVRAM part with only 32KiB of space, a smaller erase page
allows much better utilization in applications where garbage collection
is important.
Signed-off-by: Patrick O'Grady <patrick@baymotion.com>
Reviewed-by: Joern Engel <joern@logfs.org>
Link: https://lore.kernel.org/lkml/CAJ7m5OqYv_=JB9NhHsqBsa8YU0DFRoP7C+W10PY22wonAGJK=A@mail.gmail.com/
[Guohua Zhong: fix token array index out of bounds and update patch for kernel master branch]
Signed-off-by: Guohua Zhong <zhongguohua1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201207095529.20896-1-zhongguohua1@huawei.com
sparse is unhappy with us casting the __iomem address space pointer to
a type with no address space attribute specified:
"sparse warnings: (new ones prefixed by >>)"
>> drivers/mtd/maps/physmap-bt1-rom.c:78:18: sparse: sparse: cast removes address space '__iomem' of expression
Indeed we perform the __iomem-less type casting but to an integer
variable. The integer variable isn't dereferenced then, so the casting is
safe and won't cause any problem. But in order to make sparse happy and
keep the code coherent let's fix the warning by converting the local
"shift" and "chunk" variables to the "unsigned int" type (since their
value won't ever exceed three) and cast the __iomem-pointers to uintptr_t.
Add the same fix to the bt1_rom_map_read() method for unification.
Fixes: b3e79e7682 ("mtd: physmap: Add Baikal-T1 physically mapped ROM support")
Link: https://lore.kernel.org/lkml/202011021254.XC70BaQT-lkp@intel.com/
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201125072640.23516-1-Sergey.Semin@baikalelectronics.ru
Some devices (especially QCA ones) are already using hardcoded partition
names with colons in it. The OpenMesh A62 for example provides following
mtd relevant information via cmdline:
root=31:11 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(custom),64k(0:KEYS),0x002b0000(kernel),0x00c80000(rootfs),15552k(inactive) rootfsname=rootfs rootwait
The change to split only on the last colon between mtd-id and partitions
will cause newpart to see following string for the first partition:
KEYS),0x002b0000(kernel),0x00c80000(rootfs),15552k(inactive)
Such a partition list cannot be parsed and thus the device fails to boot.
Avoid this behavior by making sure that the start of the first part-name
("(") will also be the last byte the mtd-id split algorithm is using for
its colon search.
Fixes: eb13fa0227 ("mtd: parser: cmdline: Support MTD names containing one or more colons")
Cc: stable@vger.kernel.org
Cc: Ron Minnich <rminnich@google.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201124062506.185392-1-sven@narfation.org
Switch the block device lookup interfaces to directly work with a dev_t
so that struct block_device references are only acquired by the
blkdev_get variants (and the blk-cgroup special case). This means that
we now don't need an extra reference in the inode and can generally
simplify handling of struct block_device to keep the lookups contained
in the core block layer code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Coly Li <colyli@suse.de> [bcache]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This code is meant to be reused by the SPI-NAND core. Now that the
driver has been cleaned and reorganized, use a generic ECC engine
object to store the driver's data instead of accessing members of the
nand_chip structure.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-9-miquel.raynal@bootlin.com
These functions must be usable by the main NAND core, so their names
must be technology-agnostic as well as the parameters. Hence, we pass
a generic nand_device instead of a raw nand_chip structure.
As it seems that changing the raw NAND functions to always pass a
generic NAND device is a lost of time, we prefer to create dedicated
raw NAND wrappers that will be useful in the near future to do the
translation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-8-miquel.raynal@bootlin.com
The NAND BCH control structure has nothing to do outside of this
driver, all users of the nand_bch_init/free() functions just save it
to chip->ecc.priv so do it in this driver directly and return a
regular error code instead.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-5-miquel.raynal@bootlin.com
Currently, BCH and Hamming engine are sharing the same
tweaking/restoring I/O mechanism: they need the I/O request to fully
cover the main/OOB area. Let's make this code generic as sharing the
code between two drivers is already a win. Maybe other ECC engine
drivers will need it too.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-2-miquel.raynal@bootlin.com
Fixes the following W=1 kernel build warning(s):
drivers/mtd/devices/powernv_flash.c:129: warning: Cannot understand * @mtd: the device
drivers/mtd/devices/powernv_flash.c:145: warning: Cannot understand * @mtd: the device
drivers/mtd/devices/powernv_flash.c:161: warning: Cannot understand * @mtd: the device
drivers/mtd/devices/powernv_flash.c:184: warning: Function parameter or member 'dev' not described in 'powernv_flash_set_driver_info'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux-mtd@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-24-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/onenand/onenand_base.c:140: warning: Function parameter or member 'mtd' not described in 'onenand_ooblayout_32_64_ecc'
drivers/mtd/nand/onenand/onenand_base.c:140: warning: Function parameter or member 'section' not described in 'onenand_ooblayout_32_64_ecc'
drivers/mtd/nand/onenand/onenand_base.c:140: warning: Function parameter or member 'oobregion' not described in 'onenand_ooblayout_32_64_ecc'
drivers/mtd/nand/onenand/onenand_base.c:1436: warning: bad line:
drivers/mtd/nand/onenand/onenand_base.c:1971: warning: Function parameter or member 'ops' not described in 'onenand_write_oob_nolock'
drivers/mtd/nand/onenand/onenand_base.c:1971: warning: Excess function parameter 'len' description in 'onenand_write_oob_nolock'
drivers/mtd/nand/onenand/onenand_base.c:1971: warning: Excess function parameter 'retlen' description in 'onenand_write_oob_nolock'
drivers/mtd/nand/onenand/onenand_base.c:1971: warning: Excess function parameter 'buf' description in 'onenand_write_oob_nolock'
drivers/mtd/nand/onenand/onenand_base.c:1971: warning: Excess function parameter 'mode' description in 'onenand_write_oob_nolock'
drivers/mtd/nand/onenand/onenand_base.c:2156: warning: Function parameter or member 'block_size' not described in 'onenand_multiblock_erase'
drivers/mtd/nand/onenand/onenand_base.c:2156: warning: Excess function parameter 'region' description in 'onenand_multiblock_erase'
drivers/mtd/nand/onenand/onenand_base.c:2771: warning: Function parameter or member 'ops' not described in 'onenand_otp_write_oob_nolock'
drivers/mtd/nand/onenand/onenand_base.c:2771: warning: Excess function parameter 'len' description in 'onenand_otp_write_oob_nolock'
drivers/mtd/nand/onenand/onenand_base.c:2771: warning: Excess function parameter 'retlen' description in 'onenand_otp_write_oob_nolock'
drivers/mtd/nand/onenand/onenand_base.c:2771: warning: Excess function parameter 'buf' description in 'onenand_otp_write_oob_nolock'
drivers/mtd/nand/onenand/onenand_base.c:3387: warning: Function parameter or member 'mtd' not described in 'flexonenand_get_boundary'
drivers/mtd/nand/onenand/onenand_base.c:3387: warning: Excess function parameter 'onenand_info' description in 'flexonenand_get_boundary'
drivers/mtd/nand/onenand/onenand_base.c:3509: warning: Function parameter or member 'mtd' not described in 'flexonenand_check_blocks_erased'
drivers/mtd/nand/onenand/onenand_base.c:3509: warning: Excess function parameter 'mtd_info' description in 'flexonenand_check_blocks_erased'
drivers/mtd/nand/onenand/onenand_base.c:3557: warning: Function parameter or member 'die' not described in 'flexonenand_set_boundary'
drivers/mtd/nand/onenand/onenand_base.c:3557: warning: Function parameter or member 'boundary' not described in 'flexonenand_set_boundary'
drivers/mtd/nand/onenand/onenand_base.c:3557: warning: Function parameter or member 'lock' not described in 'flexonenand_set_boundary'
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-23-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/arasan-nand-controller.c:133: warning: Function parameter or member 'buf' not described in 'anfc_op'
Cc: Naga Sureshkumar Relli <nagasure@xilinx.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Choudary Kalluri <punnaia@xilinx.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-22-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/sunxi_nand.c:250: warning: Function parameter or member 'caps' not described in 'sunxi_nfc'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Boris BREZILLON <b.brezillon.dev@gmail.com>
Cc: Qiang Yu <yuq825@gmail.com>
Cc: Dmitriy B <rzk333@gmail.com>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-21-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/omap2.c:191: warning: Function parameter or member 'info' not described in 'omap_prefetch_enable'
drivers/mtd/nand/raw/omap2.c:221: warning: Function parameter or member 'cs' not described in 'omap_prefetch_reset'
drivers/mtd/nand/raw/omap2.c:221: warning: Function parameter or member 'info' not described in 'omap_prefetch_reset'
drivers/mtd/nand/raw/omap2.c:946: warning: Function parameter or member 'chip' not described in 'omap_enable_hwecc'
drivers/mtd/nand/raw/omap2.c:946: warning: Excess function parameter 'mtd' description in 'omap_enable_hwecc'
drivers/mtd/nand/raw/omap2.c:1017: warning: Function parameter or member 'chip' not described in 'omap_dev_ready'
drivers/mtd/nand/raw/omap2.c:1017: warning: Excess function parameter 'mtd' description in 'omap_dev_ready'
drivers/mtd/nand/raw/omap2.c:1036: warning: Function parameter or member 'chip' not described in 'omap_enable_hwecc_bch'
drivers/mtd/nand/raw/omap2.c:1036: warning: Excess function parameter 'mtd' description in 'omap_enable_hwecc_bch'
drivers/mtd/nand/raw/omap2.c:1142: warning: Function parameter or member 'ecc_calc' not described in '_omap_calculate_ecc_bch'
drivers/mtd/nand/raw/omap2.c:1142: warning: Excess function parameter 'ecc_code' description in '_omap_calculate_ecc_bch'
drivers/mtd/nand/raw/omap2.c:1270: warning: Function parameter or member 'ecc_calc' not described in 'omap_calculate_ecc_bch_sw'
drivers/mtd/nand/raw/omap2.c:1270: warning: Excess function parameter 'ecc_code' description in 'omap_calculate_ecc_bch_sw'
drivers/mtd/nand/raw/omap2.c:1284: warning: Function parameter or member 'ecc_calc' not described in 'omap_calculate_ecc_bch_multi'
drivers/mtd/nand/raw/omap2.c:1284: warning: Excess function parameter 'ecc_code' description in 'omap_calculate_ecc_bch_multi'
drivers/mtd/nand/raw/omap2.c:1681: warning: Function parameter or member 'info' not described in 'is_elm_present'
drivers/mtd/nand/raw/omap2.c:1681: warning: Function parameter or member 'elm_node' not described in 'is_elm_present'
drivers/mtd/nand/raw/omap2.c:1681: warning: Excess function parameter 'omap_nand_info' description in 'is_elm_present'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Jian Zhang <jzhang@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-20-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/omap_elm.c:102: warning: Function parameter or member 'ecc_steps' not described in 'elm_config'
drivers/mtd/nand/raw/omap_elm.c:102: warning: Function parameter or member 'ecc_step_size' not described in 'elm_config'
drivers/mtd/nand/raw/omap_elm.c:102: warning: Function parameter or member 'ecc_syndrome_size' not described in 'elm_config'
drivers/mtd/nand/raw/omap_elm.c:440: warning: Function parameter or member 'info' not described in 'elm_context_save'
drivers/mtd/nand/raw/omap_elm.c:488: warning: Function parameter or member 'info' not described in 'elm_context_restore'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-19-lee.jones@linaro.org
Correct 'controller' typo while we're at it.
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/s3c2410.c:172: warning: Function parameter or member 'controller' not described in 's3c2410_nand_info'
drivers/mtd/nand/raw/s3c2410.c:172: warning: Function parameter or member 'freq_transition' not described in 's3c2410_nand_info'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: linux-mtd@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-18-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/cafe_nand.c:372: warning: Function parameter or member 'page' not described in 'cafe_nand_read_page'
drivers/mtd/nand/raw/cafe_nand.c:372: warning: Excess function parameter 'mtd' description in 'cafe_nand_read_page'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-17-lee.jones@linaro.org
'dummy' is never checked (as per the nomenclature) and the use of
'emtpymatch' is currently #if 0'ed out. We could also #if 0 the
declaration, but #ifery is pretty ugly, so I like to keep it to a
minimum.
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/diskonchip.c: In function ‘DoC_Delay’:
drivers/mtd/nand/raw/diskonchip.c:219:16: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
drivers/mtd/nand/raw/diskonchip.c: In function ‘doc200x_calculate_ecc’:
drivers/mtd/nand/raw/diskonchip.c:706:6: warning: variable ‘emptymatch’ set but not used [-Wunused-but-set-variable]
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Dan Brown <dan_brown@ieee.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-16-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/ubi/gluebi.c:446: warning: Function parameter or member 'ns_ptr' not described in 'gluebi_notify'
drivers/mtd/ubi/gluebi.c:446: warning: Excess function parameter 'ptr' description in 'gluebi_notify'
Cc: Richard Weinberger <richard@nod.at>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-15-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'host' not described in 'brcmnand_edu_trans'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'addr' not described in 'brcmnand_edu_trans'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'buf' not described in 'brcmnand_edu_trans'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'len' not described in 'brcmnand_edu_trans'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'cmd' not described in 'brcmnand_edu_trans'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'host' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'desc' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'addr' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'buf' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'len' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'dma_cmd' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'begin' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'end' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'next_desc' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1977: warning: Function parameter or member 'host' not described in 'brcmnand_dma_run'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1977: warning: Function parameter or member 'desc' not described in 'brcmnand_dma_run'
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Cc: bcm-kernel-feedback-list@broadcom.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-14-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/ubi/wl.c:584: warning: Function parameter or member 'nested' not described in 'schedule_erase'
drivers/mtd/ubi/wl.c:1075: warning: Excess function parameter 'shutdown' description in '__erase_worker'
Cc: Richard Weinberger <richard@nod.at>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-13-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/ubi/eba.c:1304: warning: Function parameter or member 'vidb' not described in 'ubi_eba_copy_leb'
drivers/mtd/ubi/eba.c:1304: warning: Excess function parameter 'vid_hdr' description in 'ubi_eba_copy_leb'
drivers/mtd/ubi/eba.c:1483: warning: Function parameter or member 'ai' not described in 'print_rsvd_warning'
Cc: Richard Weinberger <richard@nod.at>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-12-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/ubi/kapi.c:464: warning: Function parameter or member 'sgl' not described in 'ubi_leb_read_sg'
drivers/mtd/ubi/kapi.c:464: warning: Excess function parameter 'buf' description in 'ubi_leb_read_sg'
Cc: Richard Weinberger <richard@nod.at>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-11-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/spi/toshiba.c:36: warning: Function parameter or member 'write_cache_variants' not described in 'SPINAND_OP_VARIANTS'
drivers/mtd/nand/spi/toshiba.c:36: warning: Function parameter or member '0' not described in 'SPINAND_OP_VARIANTS'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Yoshio Furuyama <ytc-mb-yfuruyama7@kioxia.com>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-10-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/ubi/build.c:61: warning: Function parameter or member 'ubi_num' not described in 'mtd_dev_param'
Cc: Richard Weinberger <richard@nod.at>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-9-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/spi-nor/controllers/hisi-sfc.c:328: warning: Function parameter or member 'np' not described in 'hisi_spi_nor_register'
drivers/mtd/spi-nor/controllers/hisi-sfc.c:328: warning: Function parameter or member 'host' not described in 'hisi_spi_nor_register'
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-8-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/onenand/onenand_bbt.c:33: warning: Function parameter or member 'buf' not described in 'check_short_pattern'
drivers/mtd/nand/onenand/onenand_bbt.c:33: warning: Function parameter or member 'len' not described in 'check_short_pattern'
drivers/mtd/nand/onenand/onenand_bbt.c:33: warning: Function parameter or member 'paglen' not described in 'check_short_pattern'
drivers/mtd/nand/onenand/onenand_bbt.c:33: warning: Function parameter or member 'td' not described in 'check_short_pattern'
drivers/mtd/nand/onenand/onenand_bbt.c:57: warning: Function parameter or member 'mtd' not described in 'create_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:57: warning: Function parameter or member 'buf' not described in 'create_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:57: warning: Function parameter or member 'bd' not described in 'create_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:57: warning: Function parameter or member 'chip' not described in 'create_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:132: warning: Function parameter or member 'mtd' not described in 'onenand_memory_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:132: warning: Function parameter or member 'bd' not described in 'onenand_memory_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:145: warning: Function parameter or member 'mtd' not described in 'onenand_isbad_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:145: warning: Function parameter or member 'offs' not described in 'onenand_isbad_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:145: warning: Function parameter or member 'allowbbt' not described in 'onenand_isbad_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:182: warning: Function parameter or member 'mtd' not described in 'onenand_scan_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:182: warning: Function parameter or member 'bd' not described in 'onenand_scan_bbt'
drivers/mtd/nand/onenand/onenand_bbt.c:230: warning: Function parameter or member 'mtd' not described in 'onenand_default_bbt'
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-7-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/mtdcore.c:1592: warning: Function parameter or member 'section' not described in 'mtd_ooblayout_find_eccregion'
drivers/mtd/mtdcore.c:1592: warning: Excess function parameter 'sectionp' description in 'mtd_ooblayout_find_eccregion'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-6-lee.jones@linaro.org
This patch also places the descriptions in the correct order.
Fixes the following W=1 kernel build warning(s):
drivers/mtd/devices/docg3.c:819: warning: bad line:
drivers/mtd/devices/docg3.c:1799: warning: Excess function parameter 'base' description in 'doc_probe_device'
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-5-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/onenand/onenand_base.c:140: warning: Function parameter or member 'mtd' not described in 'onenand_ooblayout_32_64_ecc'
drivers/mtd/nand/onenand/onenand_base.c:140: warning: Function parameter or member 'section' not described in 'onenand_ooblayout_32_64_ecc'
drivers/mtd/nand/onenand/onenand_base.c:140: warning: Function parameter or member 'oobregion' not described in 'onenand_ooblayout_32_64_ecc'
drivers/mtd/nand/onenand/onenand_base.c:200: warning: Function parameter or member 'addr' not described in 'onenand_readw'
drivers/mtd/nand/onenand/onenand_base.c:212: warning: Function parameter or member 'value' not described in 'onenand_writew'
drivers/mtd/nand/onenand/onenand_base.c:212: warning: Function parameter or member 'addr' not described in 'onenand_writew'
drivers/mtd/nand/onenand/onenand_base.c:225: warning: Function parameter or member 'this' not described in 'onenand_block_address'
drivers/mtd/nand/onenand/onenand_base.c:225: warning: Function parameter or member 'block' not described in 'onenand_block_address'
drivers/mtd/nand/onenand/onenand_base.c:242: warning: Function parameter or member 'this' not described in 'onenand_bufferram_address'
drivers/mtd/nand/onenand/onenand_base.c:242: warning: Function parameter or member 'block' not described in 'onenand_bufferram_address'
NB: Snipped 200 lines for brevity.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Adrian Hunter <ext-adrian.hunter@nokia.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-4-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/devices/phram.c:19: warning: Function parameter or member 'fmt' not described in 'pr_fmt'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: "Jochen Schäuble" <psionic@psionic.de>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-3-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/mtdpart.c:300: warning: Function parameter or member 'mtd' not described in '__mtd_del_partition'
drivers/mtd/mtdpart.c:300: warning: Excess function parameter 'priv' description in '__mtd_del_partition'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Thomas Gleixner <gleixner@linutronix.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-2-lee.jones@linaro.org
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-20-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-18-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-17-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-16-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-15-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-14-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-13-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-12-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-10-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-8-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-7-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-5-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-4-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip(), a NAND controller
hook.
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-3-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip(), a NAND controller
hook.
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Reported-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-2-miquel.raynal@bootlin.com
BLKFLSBUF is not supposed to actually send a flush command to the device,
but to tear down buffer cache structures. Remove the mtd_blkdevs
implementation and just use the default semantics instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since this flash doesn't have a Profile 1.0 table, the Octal DTR
capabilities are enabled in the post SFDP fixup, along with the 8D-8D-8D
fast read settings.
Enable Octal DTR mode with 20 dummy cycles to allow running at the
maximum supported frequency of 200Mhz.
The flash supports the soft reset sequence. So, add the flag in the
flash's info.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-16-p.yadav@ti.com
The Cypress Semper flash is an xSPI compliant octal DTR flash. Add
support for using it in octal DTR mode.
The flash by default boots in a hybrid sector mode. But the sector map
table on the part I had was programmed incorrectly and the SMPT values
on the flash don't match the public datasheet. Specifically, in some
places erase type 3 was used instead of 4. In addition, the region sizes
were incorrect in some places. So, for testing I set CFR3N[3] to enable
uniform sector sizes. Since the uniform sector mode bit is a
non-volatile bit, this series does not change it to avoid making any
permanent changes to the flash configuration. The correct data to
implement a fixup is not available right now and will be done in a
follow-up patch if needed.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
[vigneshr@ti.com: Drop unnecessary sleep in Octal DTR switch sequence]
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-15-p.yadav@ti.com
On resume, the init procedure will be run that will re-enable it.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-14-p.yadav@ti.com
Perform a Soft Reset on shutdown on flashes that support it so that the
flash can be reset to its initial state and any configurations made by
spi-nor (given that they're only done in volatile registers) will be
reset. This will hand back the flash in pristine state for any further
operations on it.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-13-p.yadav@ti.com
A Soft Reset sequence will return the flash to Power-on-Reset (POR)
state. It consists of two commands: Soft Reset Enable and Soft Reset.
Find out if the sequence is supported from BFPT DWORD 16.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-12-p.yadav@ti.com
Allow flashes to specify a hook to enable octal DTR mode. Use this hook
whenever possible to get optimal transfer speeds.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-11-p.yadav@ti.com
Parse just the 22nd dword and look for the 'DTR Octal Mode Enable
Volatile bit'.
SPI_NOR_IO_MODE_EN_VOLATILE should be set just for the flashes
that don't define the optional SFDP SCCR Map. For the others,
let the SFDP do its job and fill the SNOR_F_IO_MODE_EN_VOLATILE
flag. We avoid this way polluting the flash flags when declaring
one.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201005153138.6437-10-p.yadav@ti.com
We don't want to enter a stateful mode, where a X-X-X I/O mode
is entered by setting a non-volatile bit, because in case of a
reset or a crash, once in the non-volatile mode, we may not be able
to recover in bootloaders and we may break the SPI NOR boot.
Forbid by default the I/O modes that are set via a non-volatile bit.
SPI_NOR_IO_MODE_EN_VOLATILE should be set just for the flashes that
don't define the optional SFDP SCCR Map, so that we don't pollute the
flash info flags.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201005153138.6437-9-p.yadav@ti.com
Some controllers, like the cadence qspi controller, have trouble reading
only 1 byte in DTR mode. So, do 2 byte reads for SR and FSR commands in
DTR mode, and then discard the second byte.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-8-p.yadav@ti.com
The xSPI Profile 1.0 table specifies how many dummy cycles and address
bytes are needed for the Read Status Register command in octal DTR mode.
Use that information to send the correct Read SR command.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-7-p.yadav@ti.com
This table is indication that the flash is xSPI compliant and hence
supports octal DTR mode. Extract information like the fast read opcode,
dummy cycles, the number of dummy cycles needed for a Read Status
Register command, and the number of address bytes needed for a Read
Status Register command.
We don't know what speed the controller is running at. Find the fast
read dummy cycles for the fastest frequency the flash can run at to be
sure we are never short of dummy cycles. If nothing is available,
default to 20. Flashes that use a different value should update it in
their fixup hooks.
Since we want to set read settings, expose spi_nor_set_read_settings()
in core.h.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-6-p.yadav@ti.com
Some devices in DTR mode expect an extra command byte called the
extension. The extension can either be same as the opcode, bitwise
inverse of the opcode, or another additional byte forming a 16-byte
opcode. Get the extension type from the BFPT. For now, only flashes with
"repeat" and "inverse" extensions are supported.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-5-p.yadav@ti.com
Double Transfer Rate (DTR) is SPI protocol in which data is transferred
on each clock edge as opposed to on each clock cycle. Make
framework-level changes to allow supporting flashes in DTR mode.
Right now, mixed DTR modes are not supported. So, for example a mode
like 4S-4D-4D will not work. All phases need to be either DTR or STR.
The xSPI spec says that "The program commands provide SPI backward
compatible commands for programming data...". So 8D-8D-8D page program
opcodes are populated with using 1S-1S-1S opcodes.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-4-p.yadav@ti.com
They are thin wrappers around
nor->controller_ops->{read_reg,write_reg,erase}(). In a future commit
DTR support will be added. These ops can not be supported by the
controller_ops hooks and these helpers will make it easier to reject
those calls.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-3-p.yadav@ti.com
ENOTSUPP is not a SUSV4 error code. Using EOPNOTSUPP is preferred
in its stead.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201005153138.6437-2-p.yadav@ti.com
Since commit d7157ff49a ("mtd: rawnand: Use the ECC framework user
input parsing bits"), ECC are broken in FMC2 driver in case of
nand-ecc-step-size and nand-ecc-strength are not set in the device tree.
To avoid this issue, the default settings are now set in
stm32_fmc2_nfc_attach_chip function.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1604064819-26861-1-git-send-email-christophe.kerello@st.com
If a flash chip has more than 16MB capacity but its BFPT reports
BFPT_DWORD1_ADDRESS_BYTES_3_OR_4, the spi-nor framework defaults to 3.
The check in spi_nor_set_addr_width() doesn't catch it because addr_width
did get set. This fixes that check.
Fixes: f9acd7fa80 ("mtd: spi-nor: sfdp: default to addr_width of 3 for configurable widths")
Signed-off-by: Bert Vermeulen <bert@biot.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20201006132346.12652-1-bert@biot.com
No ECC initialization should happen during the host controller probe.
In fact, we need the probe function to call nand_scan() in order to:
- identify the device, its capabilities and constraints (nand_scan_ident())
- configure the ECC engine accordingly (->attach_chip())
- scan its content and prepare the core (nand_scan_tail())
Moving these lines to fsl_ifc_attach_chip() fixes a regression caused by
a previous commit supposed to clarify these steps.
Based on a fix done for the mxc_nand driver by Miquel Raynal.
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Reported-by: Han Xu <xhnjupt@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Han Xu <xhnjupt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201016132626.30112-1-festevam@gmail.com
No ECC initialization should happen during the host controller probe.
In fact, we need the probe function to call nand_scan() in order to:
- identify the device, its capabilities and constraints (nand_scan_ident())
- configure the ECC engine accordingly (->attach_chip())
- scan its content and prepare the core (nand_scan_tail())
Moving these lines to mxcnd_attach_chip() fixes a regression caused by
a previous commit supposed to clarify these steps.
When moving the ECC initialization from probe() to attach(), get rid
of the pdata usage to determine the engine type and let the core decide
instead.
Tested on a imx27-pdk board.
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Reported-by: Fabio Estevam <festevam@gmail.com>
Co-developed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201016213613.1450-1-festevam@gmail.com
UBI:
- Correctly use kthread_should_stop in ubi worker
UBIFS:
- Fixes for memory leaks while iterating directory entries
- Fix for a user triggerable error message
- Fix for a space accounting bug in authenticated mode
-----BEGIN PGP SIGNATURE-----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=RD+h
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.10-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull more ubi and ubifs updates from Richard Weinberger:
"UBI:
- Correctly use kthread_should_stop in ubi worker
UBIFS:
- Fixes for memory leaks while iterating directory entries
- Fix for a user triggerable error message
- Fix for a space accounting bug in authenticated mode"
* tag 'for-linus-5.10-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubifs: journal: Make sure to not dirty twice for auth nodes
ubifs: setflags: Don't show error message when vfs_ioc_setflags_prepare() fails
ubifs: ubifs_jnl_change_xattr: Remove assertion 'nlink > 0' for host inode
ubi: check kthread_should_stop() after the setting of task state
ubifs: dent: Fix some potential memory leaks while iterating entries
ubifs: xattr: Fix some potential memory leaks while iterating entries
* Drop useless 'depends on' in Kconfig
* Add an extra level in the Kconfig hierarchy
* Trivial spellings
* Dynamic allocation of the interface configurations
* Dropping the default ONFI timing mode
* Various cleanup (types, structures, naming, comments)
* Hide the chip->data_interface indirection
* Add the generic rb-gpios property
* Add the ->choose_interface_config() hook
* Introduce nand_choose_best_sdr_timings()
* Use default values for tPROG_max and tBERS_max
* Avoid redefining tR_max and tCCS_min
* Add a helper to find the closest ONFI mode
* bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
* fsl-upm: Deprecation of specific DT properties
* fsl_upm: Driver rework and cleanup in favor of ->exec_op()
* Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
* brcmnand: ECC error handling on EDU transfers
* brcmnand: Don't default to EDU transfers
* qcom: Set BAM mode only if not set already
* qcom: Avoid write to unavailable register
* gpio: Driver rework in favor of ->exec_op()
* tango: ->exec_op() conversion
* mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
* toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4
* toshiba: Implement ->choose_interface_config() for TC58NVG0S3E
* toshiba: Implement ->choose_interface_config() for TC58TEG5DCLTA00
* hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
HyperBus changes:
* DMA support for TI's AM654 HyperBus controller driver.
* HyperBus frontend driver for Renesas RPC-IF driver.
SPI NOR core changes:
* Support for Winbond w25q64jwm flash
* Enable 4K sector support for mx25l12805d
SPI NOR controller drivers changes:
* intel-spi Add Alder Lake-S PCI ID
MTD Core changes:
* mtdoops: Don't run panic write twice
* mtdconcat: Correctly handle panic write
* Use DEFINE_SHOW_ATTRIBUTE
-----BEGIN PGP SIGNATURE-----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=X56H
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"NAND core changes:
- Drop useless 'depends on' in Kconfig
- Add an extra level in the Kconfig hierarchy
- Trivial spellings
- Dynamic allocation of the interface configurations
- Dropping the default ONFI timing mode
- Various cleanup (types, structures, naming, comments)
- Hide the chip->data_interface indirection
- Add the generic rb-gpios property
- Add the ->choose_interface_config() hook
- Introduce nand_choose_best_sdr_timings()
- Use default values for tPROG_max and tBERS_max
- Avoid redefining tR_max and tCCS_min
- Add a helper to find the closest ONFI mode
- bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
- fsl-upm: Deprecation of specific DT properties
- fsl_upm: Driver rework and cleanup in favor of ->exec_op()
- Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
- brcmnand: ECC error handling on EDU transfers
- brcmnand: Don't default to EDU transfers
- qcom: Set BAM mode only if not set already
- qcom: Avoid write to unavailable register
- gpio: Driver rework in favor of ->exec_op()
- tango: ->exec_op() conversion
- mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
- toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4
- toshiba: Implement ->choose_interface_config() for TC58NVG0S3E
- toshiba: Implement ->choose_interface_config() for TC58TEG5DCLTA00
- hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
HyperBus changes:
- DMA support for TI's AM654 HyperBus controller driver.
- HyperBus frontend driver for Renesas RPC-IF driver.
SPI NOR core changes:
- Support for Winbond w25q64jwm flash
- Enable 4K sector support for mx25l12805d
SPI NOR controller drivers changes:
- intel-spi Add Alder Lake-S PCI ID
MTD Core changes:
- mtdoops: Don't run panic write twice
- mtdconcat: Correctly handle panic write
- Use DEFINE_SHOW_ATTRIBUTE"
* tag 'mtd/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (76 commits)
mtd: hyperbus: Fix build failure when only RPCIF_HYPERBUS is enabled
mtd: hyperbus: add Renesas RPC-IF driver
Revert "mtd: spi-nor: Prefer asynchronous probe"
mtd: parsers: bcm63xx: Do not make it modular
mtd: spear_smi: Enable compile testing
mtd: maps: vmu-flash: fix typos for struct memcard
mtd: physmap: Add Baikal-T1 physically mapped ROM support
mtd: maps: vmu-flash: simplify the return expression of probe_maple_vmu
mtd: onenand: simplify the return expression of onenand_transfer_auto_oob
mtd: rawnand: cadence: remove a redundant dev_err call
mtd: rawnand: ams-delta: Fix non-OF build warning
mtd: rawnand: Don't overwrite the error code from nand_set_ecc_soft_ops()
mtd: rawnand: Introduce nand_set_ecc_on_host_ops()
mtd: rawnand: atmel: Check return values for nand_read_data_op
mtd: rawnand: vf610: Remove unused function vf610_nfc_transfer_size()
mtd: rawnand: qcom: Simplify with dev_err_probe()
mtd: rawnand: marvell: Fix and update kerneldoc
mtd: rawnand: marvell: Simplify with dev_err_probe()
mtd: rawnand: gpmi: Simplify with dev_err_probe()
mtd: rawnand: atmel: Simplify with dev_err_probe()
...
Pull trivial updates from Jiri Kosina:
"The latest advances in computer science from the trivial queue"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
xtensa: fix Kconfig typo
spelling.txt: Remove some duplicate entries
mtd: rawnand: oxnas: cleanup/simplify code
selftests: vm: add fragment CONFIG_GUP_BENCHMARK
perf: Fix opt help text for --no-bpf-event
HID: logitech-dj: Fix spelling in comment
bootconfig: Fix kernel message mentioning CONFIG_BOOT_CONFIG
MAINTAINERS: rectify MMP SUPPORT after moving cputype.h
scif: Fix spelling of EACCES
printk: fix global comment
lib/bitmap.c: fix spello
fs: Fix missing 'bit' in comment
-----BEGIN PGP SIGNATURE-----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=LzyE
-----END PGP SIGNATURE-----
Merge tag 'block-5.10-2020-10-12' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- Series of merge handling cleanups (Baolin, Christoph)
- Series of blk-throttle fixes and cleanups (Baolin)
- Series cleaning up BDI, seperating the block device from the
backing_dev_info (Christoph)
- Removal of bdget() as a generic API (Christoph)
- Removal of blkdev_get() as a generic API (Christoph)
- Cleanup of is-partition checks (Christoph)
- Series reworking disk revalidation (Christoph)
- Series cleaning up bio flags (Christoph)
- bio crypt fixes (Eric)
- IO stats inflight tweak (Gabriel)
- blk-mq tags fixes (Hannes)
- Buffer invalidation fixes (Jan)
- Allow soft limits for zone append (Johannes)
- Shared tag set improvements (John, Kashyap)
- Allow IOPRIO_CLASS_RT for CAP_SYS_NICE (Khazhismel)
- DM no-wait support (Mike, Konstantin)
- Request allocation improvements (Ming)
- Allow md/dm/bcache to use IO stat helpers (Song)
- Series improving blk-iocost (Tejun)
- Various cleanups (Geert, Damien, Danny, Julia, Tetsuo, Tian, Wang,
Xianting, Yang, Yufen, yangerkun)
* tag 'block-5.10-2020-10-12' of git://git.kernel.dk/linux-block: (191 commits)
block: fix uapi blkzoned.h comments
blk-mq: move cancel of hctx->run_work to the front of blk_exit_queue
blk-mq: get rid of the dead flush handle code path
block: get rid of unnecessary local variable
block: fix comment and add lockdep assert
blk-mq: use helper function to test hw stopped
block: use helper function to test queue register
block: remove redundant mq check
block: invoke blk_mq_exit_sched no matter whether have .exit_sched
percpu_ref: don't refer to ref->data if it isn't allocated
block: ratelimit handle_bad_sector() message
blk-throttle: Re-use the throtl_set_slice_end()
blk-throttle: Open code __throtl_de/enqueue_tg()
blk-throttle: Move service tree validation out of the throtl_rb_first()
blk-throttle: Move the list operation after list validation
blk-throttle: Fix IO hang for a corner case
blk-throttle: Avoid tracking latency if low limit is invalid
blk-throttle: Avoid getting the current time if tg->last_finish_time is 0
blk-throttle: Remove a meaningless parameter for throtl_downgrade_state()
block: Remove redundant 'return' statement
...
commit 5de15b610f ("mtd: hyperbus: add Renesas RPC-IF driver") leads
to build failure[1] with COMPILE_TEST and RPCIF_HYPERBUS enabled. This
is because driver needs functions RENESAS_RPCIF which is only buildable
for CONFIG_ARCH_RENESAS.
Fix this by dropping COMPILE_TEST from RPCIF_HYPERBUS Kconfig entry.
This ensures driver can be built only when RENESAS_RPCIF is also
selected.
[1]:
rpc-if.c:(.text+0x20): undefined reference to `rpcif_disable_rpm' ld:
drivers/mtd/hyperbus/rpc-if.o: in function `rpcif_hb_prepare_read':
rpc-if.c:(.text+0xd6): undefined reference to `rpcif_prepare' ld:
drivers/mtd/hyperbus/rpc-if.o: in function `rpcif_hb_read16':
[...]
Fixes: 5de15b610f ("mtd: hyperbus: add Renesas RPC-IF driver") leads
Reported-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
- Support for Winbond w25q64jwm flash
- Enable 4K sector support for mx25l12805d
SPI NOR controller drivers changes:
- intel-spi:
- Add Alder Lake-S PCI ID
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEEyRC2zAhGcGjrhiNExEYeRXyRFuMFAl+AUmoQHHZpZ25lc2hy
QHRpLmNvbQAKCRDERh5FfJEW4y/WB/sH/LcaUciOptcqKQVQcQ5QVV3oj208Oj0F
f+BOk4bt0UJlKEz4szWThOL7UrNd/1jkvxn5wdz9R1pPYdvqor66wXH1fCHSJWIG
EQDIEjcNy2O7MO6oTNNXEoqPc829yUYGsxbcqz54wRHIAkJxiXJCyx3iRt+ymzIR
+NFrcsGjy4ftRo47tn/SGnDHSYtkaPiGiXWqIS114daRtMcQuJMIshalzZ5woKSp
Eyj2+fpcusM72aLtk9DEjBuQBBb7w6fL3wZuAYTFIU7utS3ruqfbTFwS9uvgiH6g
/cuddR2Ku2tBIOllmiwOEsFq/aDmxn6zWp0nW3JNq5nNRarOCfQS
=lh89
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
SPI NOR core changes:
- Support for Winbond w25q64jwm flash
- Enable 4K sector support for mx25l12805d
SPI NOR controller drivers changes:
- intel-spi:
- Add Alder Lake-S PCI ID
* Use the new generic ECC object
* Create helpers to set/extract the ECC requirements
* Create a helper to extract the ECC configuration
* Add a NAND page I/O request type
* Introduce the ECC engine framework
Raw NAND core changes:
* Don't overwrite the error code from nand_set_ecc_soft_ops()
* Introduce nand_set_ecc_on_host_ops()
* Use the NAND framework user_conf object for ECC flags
* Use the ECC framework user input parsing bits
* Use the ECC framework nand_ecc_is_strong_enough() helper
* Use the ECC framework OOB layouts
* Make use of the ECC framework
* Use nanddev_get/set_ecc_requirements() when relevant
* Use the new ECC engine type enumeration
* Separate the ECC engine type and the ECC byte placement
* Move the nand_ecc_algo enum to the generic NAND layer
* Rename the ECC algorithm enumeration items
* Add a kernel doc to the ECC algorithm enumeration
* DT bindings:
- Document boolean NAND ECC properties
- Document nand-ecc-engine
- Document nand-ecc-placement
Raw NAND drivers changes:
* Ams-Delta: Fix non-OF build warning
* Atmel:
- Check return values for nand_read_data_op
- Simplify with dev_err_probe()
- Get rid of the legacy interface implementation
- Convert the driver to exec_op()
- Use nand_prog_page_end_op()
- Use nand_{write,read}_data_op()
- Drop redundant nand_read_page_op()
- Enable the NFC controller at probe time
- Disable clk on error handling path in probe
* Cadence: remove a redundant dev_err call
* Gpmi:
- Simplify with dev_err_probe()
* Marvell:
- Fix and update kerneldoc
- Simplify with dev_err_probe()
- Fix and update kerneldoc
- Simplify with dev_err_probe()
- Support panic_write for mtdoops
* Onenand:
- Simplify the return expression of onenand_transfer_auto_oob
- Simplify with dev_err_probe()
* Oxnas: cleanup/simplify code
* Pasemi: Make pasemi_device_ready() static
* Qcom: Simplify with dev_err_probe()
* Stm32_fmc2: fix a buffer overflow
* Vf610: Remove unused function vf610_nfc_transfer_size()
SPI-NAND changes:
* Use nanddev_get_ecc_conf() when relevant
* Gigadevice:
- Add support for GD5F4GQ4xC
- Add QE Bit
- Use only one dummy byte in QUADIO
* Macronix:
- Add support for MX31UF1GE4BC
- Add support for MX31LF1GE4BC
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl+DYmkACgkQJWrqGEe9
VoQ3hQgAuKfV+RcsLq2S7jRjX3ET2U86NyqMIdTMhyu1n3EsW/Ipvu3FESMWnSQV
QO6oWogK/YstDO9huhC4dmJq9YYt3ia2e/4V3BMKpF4evCM4H16AtjKj1hl87r/L
3NDj3pvVaXxgIu7Rorr9Wk1+Fd/HSdgFXp/dqr+5EtltoKEB1/a+z5wLaCuDHjOm
btS42ihODYpefNDoakKSzYsdU1h4PyIWfqpEfWtQD1AAuaqIotfbjUO1oOjjdx+7
Lxy055VhwWpjUlU7bJhIM6qMj7JvB+ApFudB9ddg7VQITv+gb5ectsTZOfrGd27r
YX1/b8i1kAEZJ0uI/cz1MY1lYa8/xA==
=GSLS
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
NAND core changes:
* Use the new generic ECC object
* Create helpers to set/extract the ECC requirements
* Create a helper to extract the ECC configuration
* Add a NAND page I/O request type
* Introduce the ECC engine framework
Raw NAND core changes:
* Don't overwrite the error code from nand_set_ecc_soft_ops()
* Introduce nand_set_ecc_on_host_ops()
* Use the NAND framework user_conf object for ECC flags
* Use the ECC framework user input parsing bits
* Use the ECC framework nand_ecc_is_strong_enough() helper
* Use the ECC framework OOB layouts
* Make use of the ECC framework
* Use nanddev_get/set_ecc_requirements() when relevant
* Use the new ECC engine type enumeration
* Separate the ECC engine type and the ECC byte placement
* Move the nand_ecc_algo enum to the generic NAND layer
* Rename the ECC algorithm enumeration items
* Add a kernel doc to the ECC algorithm enumeration
* DT bindings:
- Document boolean NAND ECC properties
- Document nand-ecc-engine
- Document nand-ecc-placement
Raw NAND drivers changes:
* Ams-Delta: Fix non-OF build warning
* Atmel:
- Check return values for nand_read_data_op
- Simplify with dev_err_probe()
- Get rid of the legacy interface implementation
- Convert the driver to exec_op()
- Use nand_prog_page_end_op()
- Use nand_{write,read}_data_op()
- Drop redundant nand_read_page_op()
- Enable the NFC controller at probe time
- Disable clk on error handling path in probe
* Cadence: remove a redundant dev_err call
* Gpmi:
- Simplify with dev_err_probe()
* Marvell:
- Fix and update kerneldoc
- Simplify with dev_err_probe()
- Fix and update kerneldoc
- Simplify with dev_err_probe()
- Support panic_write for mtdoops
* Onenand:
- Simplify the return expression of onenand_transfer_auto_oob
- Simplify with dev_err_probe()
* Oxnas: cleanup/simplify code
* Pasemi: Make pasemi_device_ready() static
* Qcom: Simplify with dev_err_probe()
* Stm32_fmc2: fix a buffer overflow
* Vf610: Remove unused function vf610_nfc_transfer_size()
SPI-NAND changes:
* Use nanddev_get_ecc_conf() when relevant
* Gigadevice:
- Add support for GD5F4GQ4xC
- Add QE Bit
- Use only one dummy byte in QUADIO
* Macronix:
- Add support for MX31UF1GE4BC
- Add support for MX31LF1GE4BC
Add the HyperFLash driver for the Renesas RPC-IF. It's the "front end"
driver using the "back end" APIs in the main driver to talk to the real
hardware.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/78abb851-2beb-fe7d-87e5-ce58ee877d35@gmail.com
This reverts commit 03edda0e1e.
This leads to warn dump like [1] on some platforms and reorders MTD
devices which may break user space expectations [2]. So revert the change.
[1]:
[ 1.849801] ------------[ cut here ]------------
[ 1.854271] mscc_felix 0000:00:00.5: device is disabled, skipping
[ 1.858753] WARNING: CPU: 1 PID: 7 at kernel/kmod.c:136 __request_module+0x3a4/0x568
[...]
[2] Bug report: https://lore.kernel.org/linux-mtd/20201003150633.23416-1-michael@walle.cc/
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201005090321.8724-1-vigneshr@ti.com
With commit 91e81150d3 ("mtd: parsers: bcm63xx: simplify CFE
detection"), we generate a reference to fw_arg3 which is the fourth
firmware/command line argument on MIPS platforms. That symbol is not
exported and would cause a linking failure.
The parser is typically necessary to boot a BCM63xx-based system anyway
so having it be part of the kernel image makes sense, therefore make it
'bool' instead of 'tristate'.
Fixes: 91e81150d3 ("mtd: parsers: bcm63xx: simplify CFE detection")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929172726.30469-1-f.fainelli@gmail.com
Baikal-T1 Boot Controller provides an access to a RO storages, which are
physically mapped into the SoC MMIO space. In particularly there are
Internal ROM embedded into the SoC with a pre-installed firmware,
externally attached SPI flash (also accessed in the read-only mode) and a
memory region, which mirrors one of them in accordance with the currently
enabled system boot mode (also called Boot ROM).
This commit adds the Internal ROM support to the physmap driver of the MTD
kernel subsystem. The driver will create the Internal ROM MTD as long as
it is defined in the system dts file. The physically mapped SPI flash
region will be used to implement the SPI-mem interface. The mirroring
memory region won't be accessible directly since it's redundant due to
both bootable regions being exposed anyway.
Note we had to create a dedicated code for the ROMs since read from the
corresponding memory regions must be done via the dword-aligned addresses.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: linux-mips@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200920111445.21816-1-Sergey.Semin@baikalelectronics.ru
There is an error message within devm_ioremap_resource already, so
remove the dev_err call to avoid a redundant error message.
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200921013805.1724606-1-liushixin2@huawei.com
Commit 7c2f66a960 ("mtd: rawnand: ams-delta: Add module device
tables") introduced an OF module device table but wrapped a reference
to it with of_match_ptr() which resolves to NULL in non-OF configs.
That resulted in a clang compiler warning on unused variable in non-OF
builds. Fix it.
drivers/mtd/nand/raw/ams-delta.c:373:34: warning: unused variable 'gpio_nand_of_id_table' [-Wunused-const-variable]
static const struct of_device_id gpio_nand_of_id_table[] = {
^
1 warning generated.
Fixes: 7c2f66a960 ("mtd: rawnand: ams-delta: Add module device tables")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200919080403.17520-1-jmkrzyszt@gmail.com
The error code received from nand_set_ecc_soft_ops() was overwritten,
drop this redundant assignment and use the error code received from
the callee.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200917075213.532161-4-tudor.ambarus@microchip.com
There were too many levels of indentation and the code was
hard to read. Introduce a new function, similar to
nand_set_ecc_soft_ops().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200917075213.532161-3-tudor.ambarus@microchip.com
In atmel_nand_pmecc_read_pg(), nand_read_data_op() is called twice
without the return values being checked for errors. Add these checks.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200914214245.14626-1-alex.dewar90@gmail.com
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-6-krzk@kernel.org
Fix kerneldoc comments and add missing documentation for members to fix
W=1 compile warnings like:
drivers/mtd/nand/raw/marvell_nand.c:251: warning:
cannot understand function prototype: 'struct marvell_hw_ecc_layout '
drivers/mtd/nand/raw/marvell_nand.c:342: warning:
Function parameter or member 'layout' not described in 'marvell_nand_chip'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-5-krzk@kernel.org
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-4-krzk@kernel.org
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-3-krzk@kernel.org
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-2-krzk@kernel.org
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-1-krzk@kernel.org
The following GigaDevice chips have the QE BIT in the feature flags, I
checked the datasheets, but did not try this.
* GD5F1GQ4xExxG
* GD5F1GQ4xFxxG
* GD5F1GQ4UAYIG
* GD5F4GQ4UAYIG
The Quad operations like 0xEB mention that the QE bit has to be set.
Fixes: c93c613214 ("mtd: spinand: add support for GigaDevice GD5FxGQ4xA")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200820165121.3192-3-hauke@hauke-m.de
The datasheet only lists one dummy byte in the 0xEH operation for the
following chips:
* GD5F1GQ4xExxG
* GD5F1GQ4xFxxG
* GD5F1GQ4UAYIG
* GD5F4GQ4UAYIG
Fixes: c93c613214 ("mtd: spinand: add support for GigaDevice GD5FxGQ4xA")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200820165121.3192-2-hauke@hauke-m.de
vf610_nfc_probe() does not invoke clk_disable_unprepare() on one error
handling path. The patch fixes that.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 6f0ce4dfc5 ("mtd: rawnand: vf610: Avoid a potential NULL pointer dereference")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200806072634.23528-1-novikov@ispras.ru
The Macronix MX31UF1GE4BC is a 1.8V, 1Gbit (128MB) serial
NAND flash device.
Validated by read, erase, read back, write and read back
on Xilinx Zynq PicoZed FPGA board which included
Macronix SPI Host (driver/spi/spi-mxic.c).
Signed-off-by: YouChing Lin <ycllin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1595404978-31079-3-git-send-email-ycllin@mxic.com.tw
The Macronix MX31LF1GE4BC is a 3V, 1Gbit (128MB) serial
NAND flash device.
Validated by read, erase, read back, write and read back
on Xilinx Zynq PicoZed FPGA board which included
Macronix SPI Host (driver/spi/spi-mxic.c).
Signed-off-by: YouChing Lin <ycllin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1595404978-31079-2-git-send-email-ycllin@mxic.com.tw
The sparse tool complains as follows:
drivers/mtd/nand/raw/pasemi_nand.c:71:5: warning:
symbol 'pasemi_device_ready' was not declared. Should it be static?
This function is not used outside of pasemi_nand.c, so this commit
marks it static.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200721151657.41027-1-weiyongjun1@huawei.com
Now that exec_op() is implemented, we can get rid of all the legacy
hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200720131356.1579073-7-tudor.ambarus@microchip.com
Use the nand_{write,read}_data_op() helpers instead of calling the
atmel_nand_{read,write}_buf() functions directly. This will ease the
transition to exec_op().
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200720131356.1579073-4-tudor.ambarus@microchip.com
No need to enable it everytime select_chip() is called. If we really
care about PM, we should implement runtime PM hooks and disable the
controller and all its clocks when the controller has been unused for
some time.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200720131356.1579073-2-tudor.ambarus@microchip.com
Many helpers are generic to all NAND chips, they should not be
raw-NAND specific, so use the generic ones.
To avoid moving all the raw NAND core "history" into the generic NAND
layer, we keep a part of this parsing in the raw NAND core to ensure
backward compatibility.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-20-miquel.raynal@bootlin.com
AM654 HyperBus controller provides MMIO interface to read data from
flash. So add DMA memcpy support for reading data over MMIO interface.
This provides 5x improvement in throughput and reduces CPU usage as
well.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200924081214.16934-5-vigneshr@ti.com
Recent genpd changes for K3 platform ensure device is ON before driver
probe is called. Therefore, drop redundant pm_runtime_* calls from
driver to simplify the code.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200924081214.16934-4-vigneshr@ti.com
Setting up of direct mapping should be done with flash node's IO
address space and not with controller's IO region.
Fixes: b6fe8bc67d ("mtd: hyperbus: move direct mapping setup to AM654 HBMC driver")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200924081214.16934-3-vigneshr@ti.com
Add support Winbond w25q{64,128,256}jwm which are identical to existing
w25q32jwm except for their sizes.
This was tested with w25q64jwm, basic erase/write/readback and
lock/unlock both lower/upper blocks were okay.
Signed-off-by: ikjn@chromium.org <ikjn@chromium.org>
Signed-off-by: Xingyu Wu <wuxy@bitland.corp-partner.google.com>
Signed-off-by: ST Lin <stlin2@winbond.com>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200928060631.2090541-1-ikjn@chromium.org
Intel Alder Lake-S has the same SPI serial flash controller as Cannon
Lake. Add Alder Lake-S PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200925095109.51148-1-mika.westerberg@linux.intel.com
On my system the spi_nor_probe() took ~6 ms at bootup. That's not a
lot, but every little bit adds up to a slow bootup. While we can get
this out of the boot path by making it a module, there are times where
it is convenient (or even required) for this to be builtin the kernel.
Let's set that we prefer async probe so that we don't block other
drivers from probing while we are probing.
This is a tiny little change that is almost guaranteed to be safe for
anything that is able to run as a module, which SPI_NOR is.
Specifically modules are already probed asynchronously. Also: since
other things in the system may have enabled asynchronous probe the
system may already be doing other things during our probe.
There is a small possibility that some other driver that was a client
of SPI_NOR didn't handle -EPROBE_DEFER and was relying on probe
ordering and only worked when the SPI_NOR and the SPI bus were
builtin. In that case the other driver has a bug that's waiting to
hit and the other driver should be fixed.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200902160002.1.I658d1c0db9adfeb9a59bc55e96a19e192c959e55@changeid
Mechanical switch from the legacy "mode" enumeration to the new
"engine type" enumeration in drivers and board files.
The device tree parsing is also updated to return the new enumeration
from the old strings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-11-miquel.raynal@bootlin.com
The use of "syndrome" placement should not be encoded in the ECC
engine mode/type.
Create a "placement" field in NAND chip and change all occurrences of
the NAND_ECC_HW_SYNDROME enumeration to be just NAND_ECC_HW and
possibly a placement entry like NAND_ECC_PLACEMENT_INTERLEAVED.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200827085208.16276-10-miquel.raynal@bootlin.com
Set up a readahead size by default, as very few users have a good
reason to change it. This means code, ecryptfs, and orangefs now
set up the values while they were previously missing it, while ubifs,
mtd and vboxsf manually set it to 0 to avoid readahead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Acked-by: David Sterba <dsterba@suse.com> [btrfs]
Acked-by: Richard Weinberger <richard@nod.at> [ubifs, mtd]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A detach hung is possible when a race occurs between the detach process
and the ubi background thread. The following sequences outline the race:
ubi thread: if (list_empty(&ubi->works)...
ubi detach: set_bit(KTHREAD_SHOULD_STOP, &kthread->flags)
=> by kthread_stop()
wake_up_process()
=> ubi thread is still running, so 0 is returned
ubi thread: set_current_state(TASK_INTERRUPTIBLE)
schedule()
=> ubi thread will never be scheduled again
ubi detach: wait_for_completion()
=> hung task!
To fix that, we need to check kthread_should_stop() after we set the
task state, so the ubi thread will either see the stop bit and exit or
the task state is reset to runnable such that it isn't scheduled out
indefinitely.
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Cc: <stable@vger.kernel.org>
Fixes: 801c135ce7 ("UBI: Unsorted Block Images")
Reported-by: syzbot+853639d0cb16c31c7a14@syzkaller.appspotmail.com
Signed-off-by: Richard Weinberger <richard@nod.at>
As the only user has been removed in previous patch, let's revert
this one together.
This reverts commit be192209d5.
Reported-by: Matthias Weisser <m.weisser.m@gmail.com>
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/1599205640-26690-2-git-send-email-yangyicong@hisilicon.com
Previous patch intends to restore the flash's QE bit when removed/shutdown,
but may have some problems and break the flash:
- for those originally in Quad mode, this patch will clear the QE bit
when unloaded the flash, which is incorrect.
- even with above problem solved, it may still break the flash as some
flash's QE bit is non-volatile and lots of set/reset will wear out
the bit.
- the restore method cannot be proved to be valid as if a hard
reset or accident crash happened, the spi_nor_restore() won't be
performed the the QE bit will not be restored as we expected to.
So let's revert it to fix this. The discussion can be found at [1].
This reverts commit cc59e6bb6c.
[1] https://lore.kernel.org/linux-mtd/CAO8h3eFLVLRmw7u+rurKsg7=Nh2q-HVq-HgVXig8gf5Dffk8MA@mail.gmail.com/
Reported-by: Matthias Weisser <m.weisser.m@gmail.com>
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/1599205640-26690-1-git-send-email-yangyicong@hisilicon.com
Variable 'size' is being assigned the value zero that will never be
read. The assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200910154451.752569-1-colin.king@canonical.com
