[ Note: The TCP changes here is mainly to implement the bpf
pieces into the bpf_skops_*() functions introduced
in the earlier patches. ]
The earlier effort in BPF-TCP-CC allows the TCP Congestion Control
algorithm to be written in BPF. It opens up opportunities to allow
a faster turnaround time in testing/releasing new congestion control
ideas to production environment.
The same flexibility can be extended to writing TCP header option.
It is not uncommon that people want to test new TCP header option
to improve the TCP performance. Another use case is for data-center
that has a more controlled environment and has more flexibility in
putting header options for internal only use.
For example, we want to test the idea in putting maximum delay
ACK in TCP header option which is similar to a draft RFC proposal [1].
This patch introduces the necessary BPF API and use them in the
TCP stack to allow BPF_PROG_TYPE_SOCK_OPS program to parse
and write TCP header options. It currently supports most of
the TCP packet except RST.
Supported TCP header option:
───────────────────────────
This patch allows the bpf-prog to write any option kind.
Different bpf-progs can write its own option by calling the new helper
bpf_store_hdr_opt(). The helper will ensure there is no duplicated
option in the header.
By allowing bpf-prog to write any option kind, this gives a lot of
flexibility to the bpf-prog. Different bpf-prog can write its
own option kind. It could also allow the bpf-prog to support a
recently standardized option on an older kernel.
Sockops Callback Flags:
──────────────────────
The bpf program will only be called to parse/write tcp header option
if the following newly added callback flags are enabled
in tp->bpf_sock_ops_cb_flags:
BPF_SOCK_OPS_PARSE_UNKNOWN_HDR_OPT_CB_FLAG
BPF_SOCK_OPS_PARSE_ALL_HDR_OPT_CB_FLAG
BPF_SOCK_OPS_WRITE_HDR_OPT_CB_FLAG
A few words on the PARSE CB flags. When the above PARSE CB flags are
turned on, the bpf-prog will be called on packets received
at a sk that has at least reached the ESTABLISHED state.
The parsing of the SYN-SYNACK-ACK will be discussed in the
"3 Way HandShake" section.
The default is off for all of the above new CB flags, i.e. the bpf prog
will not be called to parse or write bpf hdr option. There are
details comment on these new cb flags in the UAPI bpf.h.
sock_ops->skb_data and bpf_load_hdr_opt()
─────────────────────────────────────────
sock_ops->skb_data and sock_ops->skb_data_end covers the whole
TCP header and its options. They are read only.
The new bpf_load_hdr_opt() helps to read a particular option "kind"
from the skb_data.
Please refer to the comment in UAPI bpf.h. It has details
on what skb_data contains under different sock_ops->op.
3 Way HandShake
───────────────
The bpf-prog can learn if it is sending SYN or SYNACK by reading the
sock_ops->skb_tcp_flags.
* Passive side
When writing SYNACK (i.e. sock_ops->op == BPF_SOCK_OPS_WRITE_HDR_OPT_CB),
the received SYN skb will be available to the bpf prog. The bpf prog can
use the SYN skb (which may carry the header option sent from the remote bpf
prog) to decide what bpf header option should be written to the outgoing
SYNACK skb. The SYN packet can be obtained by getsockopt(TCP_BPF_SYN*).
More on this later. Also, the bpf prog can learn if it is in syncookie
mode (by checking sock_ops->args[0] == BPF_WRITE_HDR_TCP_SYNACK_COOKIE).
The bpf prog can store the received SYN pkt by using the existing
bpf_setsockopt(TCP_SAVE_SYN). The example in a later patch does it.
[ Note that the fullsock here is a listen sk, bpf_sk_storage
is not very useful here since the listen sk will be shared
by many concurrent connection requests.
Extending bpf_sk_storage support to request_sock will add weight
to the minisock and it is not necessary better than storing the
whole ~100 bytes SYN pkt. ]
When the connection is established, the bpf prog will be called
in the existing PASSIVE_ESTABLISHED_CB callback. At that time,
the bpf prog can get the header option from the saved syn and
then apply the needed operation to the newly established socket.
The later patch will use the max delay ack specified in the SYN
header and set the RTO of this newly established connection
as an example.
The received ACK (that concludes the 3WHS) will also be available to
the bpf prog during PASSIVE_ESTABLISHED_CB through the sock_ops->skb_data.
It could be useful in syncookie scenario. More on this later.
There is an existing getsockopt "TCP_SAVED_SYN" to return the whole
saved syn pkt which includes the IP[46] header and the TCP header.
A few "TCP_BPF_SYN*" getsockopt has been added to allow specifying where to
start getting from, e.g. starting from TCP header, or from IP[46] header.
The new getsockopt(TCP_BPF_SYN*) will also know where it can get
the SYN's packet from:
- (a) the just received syn (available when the bpf prog is writing SYNACK)
and it is the only way to get SYN during syncookie mode.
or
- (b) the saved syn (available in PASSIVE_ESTABLISHED_CB and also other
existing CB).
The bpf prog does not need to know where the SYN pkt is coming from.
The getsockopt(TCP_BPF_SYN*) will hide this details.
Similarly, a flags "BPF_LOAD_HDR_OPT_TCP_SYN" is also added to
bpf_load_hdr_opt() to read a particular header option from the SYN packet.
* Fastopen
Fastopen should work the same as the regular non fastopen case.
This is a test in a later patch.
* Syncookie
For syncookie, the later example patch asks the active
side's bpf prog to resend the header options in ACK. The server
can use bpf_load_hdr_opt() to look at the options in this
received ACK during PASSIVE_ESTABLISHED_CB.
* Active side
The bpf prog will get a chance to write the bpf header option
in the SYN packet during WRITE_HDR_OPT_CB. The received SYNACK
pkt will also be available to the bpf prog during the existing
ACTIVE_ESTABLISHED_CB callback through the sock_ops->skb_data
and bpf_load_hdr_opt().
* Turn off header CB flags after 3WHS
If the bpf prog does not need to write/parse header options
beyond the 3WHS, the bpf prog can clear the bpf_sock_ops_cb_flags
to avoid being called for header options.
Or the bpf-prog can select to leave the UNKNOWN_HDR_OPT_CB_FLAG on
so that the kernel will only call it when there is option that
the kernel cannot handle.
[1]: draft-wang-tcpm-low-latency-opt-00
https://tools.ietf.org/html/draft-wang-tcpm-low-latency-opt-00
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200820190104.2885895-1-kafai@fb.com
A later patch needs to add a few pointers and a few u8 to
sock_ops_kern. Hence, this patch saves some spaces by moving
some of the existing members from u32 to u8 so that the later
patch can still fit everything in a cacheline.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200820190058.2885640-1-kafai@fb.com
bpf_get_[stack|stackid] on perf_events with precise_ip uses callchain
attached to perf_sample_data. If this callchain is not presented, do not
allow attaching BPF program that calls bpf_get_[stack|stackid] to this
event.
In the error case, -EPROTO is returned so that libbpf can identify this
error and print proper hint message.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200723180648.1429892-3-songliubraving@fb.com
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-07-21
The following pull-request contains BPF updates for your *net-next* tree.
We've added 46 non-merge commits during the last 6 day(s) which contain
a total of 68 files changed, 4929 insertions(+), 526 deletions(-).
The main changes are:
1) Run BPF program on socket lookup, from Jakub.
2) Introduce cpumap, from Lorenzo.
3) s390 JIT fixes, from Ilya.
4) teach riscv JIT to emit compressed insns, from Luke.
5) use build time computed BTF ids in bpf iter, from Yonghong.
====================
Purely independent overlapping changes in both filter.h and xdp.h
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper that copies either a native or compat bpf_fprog from
userspace after verifying the length, and remove the compat setsockopt
handlers that now aren't required.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following ipv4 stack changes, run a BPF program attached to netns before
looking up a listening socket. Program can return a listening socket to use
as result of socket lookup, fail the lookup, or take no action.
Suggested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200717103536.397595-7-jakub@cloudflare.com
Run a BPF program before looking up a listening socket on the receive path.
Program selects a listening socket to yield as result of socket lookup by
calling bpf_sk_assign() helper and returning SK_PASS code. Program can
revert its decision by assigning a NULL socket with bpf_sk_assign().
Alternatively, BPF program can also fail the lookup by returning with
SK_DROP, or let the lookup continue as usual with SK_PASS on return, when
no socket has been selected with bpf_sk_assign().
This lets the user match packets with listening sockets freely at the last
possible point on the receive path, where we know that packets are destined
for local delivery after undergoing policing, filtering, and routing.
With BPF code selecting the socket, directing packets destined to an IP
range or to a port range to a single socket becomes possible.
In case multiple programs are attached, they are run in series in the order
in which they were attached. The end result is determined from return codes
of all the programs according to following rules:
1. If any program returned SK_PASS and selected a valid socket, the socket
is used as result of socket lookup.
2. If more than one program returned SK_PASS and selected a socket,
last selection takes effect.
3. If any program returned SK_DROP, and no program returned SK_PASS and
selected a socket, socket lookup fails with -ECONNREFUSED.
4. If all programs returned SK_PASS and none of them selected a socket,
socket lookup continues to htable-based lookup.
Suggested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200717103536.397595-5-jakub@cloudflare.com
Add a new program type BPF_PROG_TYPE_SK_LOOKUP with a dedicated attach type
BPF_SK_LOOKUP. The new program kind is to be invoked by the transport layer
when looking up a listening socket for a new connection request for
connection oriented protocols, or when looking up an unconnected socket for
a packet for connection-less protocols.
When called, SK_LOOKUP BPF program can select a socket that will receive
the packet. This serves as a mechanism to overcome the limits of what
bind() API allows to express. Two use-cases driving this work are:
(1) steer packets destined to an IP range, on fixed port to a socket
192.0.2.0/24, port 80 -> NGINX socket
(2) steer packets destined to an IP address, on any port to a socket
198.51.100.1, any port -> L7 proxy socket
In its run-time context program receives information about the packet that
triggered the socket lookup. Namely IP version, L4 protocol identifier, and
address 4-tuple. Context can be further extended to include ingress
interface identifier.
To select a socket BPF program fetches it from a map holding socket
references, like SOCKMAP or SOCKHASH, and calls bpf_sk_assign(ctx, sk, ...)
helper to record the selection. Transport layer then uses the selected
socket as a result of socket lookup.
In its basic form, SK_LOOKUP acts as a filter and hence must return either
SK_PASS or SK_DROP. If the program returns with SK_PASS, transport should
look for a socket to receive the packet, or use the one selected by the
program if available, while SK_DROP informs the transport layer that the
lookup should fail.
This patch only enables the user to attach an SK_LOOKUP program to a
network namespace. Subsequent patches hook it up to run on local delivery
path in ipv4 and ipv6 stacks.
Suggested-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200717103536.397595-3-jakub@cloudflare.com
When evaluating access control over kallsyms visibility, credentials at
open() time need to be used, not the "current" creds (though in BPF's
case, this has likely always been the same). Plumb access to associated
file->f_cred down through bpf_dump_raw_ok() and its callers now that
kallsysm_show_value() has been refactored to take struct cred.
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: bpf@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes: 7105e828c0 ("bpf: allow for correlation of maps and helpers in dump")
Signed-off-by: Kees Cook <keescook@chromium.org>
In order to perform future tests against the cred saved during open(),
switch kallsyms_show_value() to operate on a cred, and have all current
callers pass current_cred(). This makes it very obvious where callers
are checking the wrong credential in their "read" contexts. These will
be fixed in the coming patches.
Additionally switch return value to bool, since it is always used as a
direct permission check, not a 0-on-success, negative-on-error style
function return.
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
<linux/cryptohash.h> sounds very generic and important, like it's the
header to include if you're doing cryptographic hashing in the kernel.
But actually it only includes the library implementation of the SHA-1
compression function (not even the full SHA-1). This should basically
never be used anymore; SHA-1 is no longer considered secure, and there
are much better ways to do cryptographic hashing in the kernel.
Remove this header and fold it into <crypto/sha.h> which already
contains constants and functions for SHA-1 (along with SHA-2).
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The library implementation of the SHA-1 compression function is
confusingly called just "sha_transform()". Alongside it are some "SHA_"
constants and "sha_init()". Presumably these are left over from a time
when SHA just meant SHA-1. But now there are also SHA-2 and SHA-3, and
moreover SHA-1 is now considered insecure and thus shouldn't be used.
Therefore, rename these functions and constants to make it very clear
that they are for SHA-1. Also add a comment to make it clear that these
shouldn't be used.
For the extra-misleadingly named "SHA_MESSAGE_BYTES", rename it to
SHA1_BLOCK_SIZE and define it to just '64' rather than '(512/8)' so that
it matches the same definition in <crypto/sha.h>. This prepares for
merging <linux/cryptohash.h> into <crypto/sha.h>.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
gcc-10 warns about accesses to zero-length arrays:
kernel/bpf/core.c: In function 'bpf_patch_insn_single':
cc1: warning: writing 8 bytes into a region of size 0 [-Wstringop-overflow=]
In file included from kernel/bpf/core.c:21:
include/linux/filter.h:550:20: note: at offset 0 to object 'insnsi' with size 0 declared here
550 | struct bpf_insn insnsi[0];
| ^~~~~~
In this case, we really want to have two flexible-array members,
but that is not possible. Removing the union to make insnsi a
flexible-array member while leaving insns as a zero-length array
fixes the warning, as nothing writes to the other one in that way.
This trick only works on linux-3.18 or higher, as older versions
had additional members in the union.
Fixes: 60a3b2253c ("net: bpf: make eBPF interpreter images read-only")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200430213101.135134-6-arnd@arndb.de
linux-next build bot reported compile issue [1] with one of its
configs. It looks like when we have CONFIG_NET=n and
CONFIG_BPF{,_SYSCALL}=y, we are missing the bpf_base_func_proto
definition (from net/core/filter.c) in cgroup_base_func_proto.
I'm reshuffling the code a bit to make it work. The common helpers
are moved into kernel/bpf/helpers.c and the bpf_base_func_proto is
exported from there.
Also, bpf_get_raw_cpu_id goes into kernel/bpf/core.c akin to existing
bpf_user_rnd_u32.
[1] https://lore.kernel.org/linux-next/CAKH8qBsBvKHswiX1nx40LgO+BGeTmb1NX8tiTttt_0uu6T3dCA@mail.gmail.com/T/#mff8b0c083314c68c2e2ef0211cb11bc20dc13c72
Fixes: 0456ea170c ("bpf: Enable more helpers for BPF_PROG_TYPE_CGROUP_{DEVICE,SYSCTL,SOCKOPT}")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200424235941.58382-1-sdf@google.com
Adding name to 'struct bpf_ksym' object to carry the name
of the symbol for bpf_prog, bpf_trampoline, bpf_dispatcher
objects.
The current benefit is that name is now generated only when
the symbol is added to the list, so we don't need to generate
it every time it's accessed.
The future benefit is that we will have all the bpf objects
symbols represented by struct bpf_ksym.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200312195610.346362-5-jolsa@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Adding bpf_trampoline_ name prefix for DECLARE_BPF_DISPATCHER,
so all the dispatchers have the common name prefix.
And also a small '_' cleanup for bpf_dispatcher_nopfunc function
name.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200312195610.346362-3-jolsa@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Replace the preemption disable/enable with migrate_disable/enable() to
reflect the actual requirement and to allow PREEMPT_RT to substitute it
with an actual migration disable mechanism which does not disable
preemption.
Including the code paths that go via __bpf_prog_run_save_cb().
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200224145643.998293311@linutronix.de
All of these cases are strictly of the form:
preempt_disable();
BPF_PROG_RUN(...);
preempt_enable();
Replace this with bpf_prog_run_pin_on_cpu() which wraps BPF_PROG_RUN()
with:
migrate_disable();
BPF_PROG_RUN(...);
migrate_enable();
On non RT enabled kernels this maps to preempt_disable/enable() and on RT
enabled kernels this solely prevents migration, which is sufficient as
there is no requirement to prevent reentrancy to any BPF program from a
preempting task. The only requirement is that the program stays on the same
CPU.
Therefore, this is a trivially correct transformation.
The seccomp loop does not need protection over the loop. It only needs
protection per BPF filter program
[ tglx: Converted to bpf_prog_run_pin_on_cpu() ]
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200224145643.691493094@linutronix.de
As already discussed in the previous change which introduced
BPF_RUN_PROG_PIN_ON_CPU() BPF only requires to disable migration to
guarantee per CPUness.
If RT substitutes the preempt disable based migration protection then the
cant_sleep() check will obviously trigger as preemption is not disabled.
Replace it by cant_migrate() which maps to cant_sleep() on a non RT kernel
and will verify that migration is disabled on a full RT kernel.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200224145643.583038889@linutronix.de
BPF programs require to run on one CPU to completion as they use per CPU
storage, but according to Alexei they don't need reentrancy protection as
obviously BPF programs running in thread context can always be 'preempted'
by hard and soft interrupts and instrumentation and the same program can
run concurrently on a different CPU.
The currently used mechanism to ensure CPUness is to wrap the invocation
into a preempt_disable/enable() pair. Disabling preemption is also
disabling migration for a task.
preempt_disable/enable() is used because there is no explicit way to
reliably disable only migration.
Provide a separate macro to invoke a BPF program which can be used in
migrateable task context.
It wraps BPF_PROG_RUN() in a migrate_disable/enable() pair which maps on
non RT enabled kernels to preempt_disable/enable(). On RT enabled kernels
this merely disables migration. Both methods ensure that the invoked BPF
program runs on one CPU to completion.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200224145643.474592620@linutronix.de
Since the bulk queue used by XDP_REDIRECT now lives in struct net_device,
we can re-use the bulking for the non-map version of the bpf_redirect()
helper. This is a simple matter of having xdp_do_redirect_slow() queue the
frame on the bulk queue instead of sending it out with __bpf_tx_xdp().
Unfortunately we can't make the bpf_redirect() helper return an error if
the ifindex doesn't exit (as bpf_redirect_map() does), because we don't
have a reference to the network namespace of the ingress device at the time
the helper is called. So we have to leave it as-is and keep the device
lookup in xdp_do_redirect_slow().
Since this leaves less reason to have the non-map redirect code in a
separate function, so we get rid of the xdp_do_redirect_slow() function
entirely. This does lose us the tracepoint disambiguation, but fortunately
the xdp_redirect and xdp_redirect_map tracepoints use the same tracepoint
entry structures. This means both can contain a map index, so we can just
amend the tracepoint definitions so we always emit the xdp_redirect(_err)
tracepoints, but with the map ID only populated if a map is present. This
means we retire the xdp_redirect_map(_err) tracepoints entirely, but keep
the definitions around in case someone is still listening for them.
With this change, the performance of the xdp_redirect sample program goes
from 5Mpps to 8.4Mpps (a 68% increase).
Since the flush functions are no longer map-specific, rename the flush()
functions to drop _map from their names. One of the renamed functions is
the xdp_do_flush_map() callback used in all the xdp-enabled drivers. To
keep from having to update all drivers, use a #define to keep the old name
working, and only update the virtual drivers in this patch.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/157918768505.1458396.17518057312953572912.stgit@toke.dk
This patch makes "struct tcp_congestion_ops" to be the first user
of BPF STRUCT_OPS. It allows implementing a tcp_congestion_ops
in bpf.
The BPF implemented tcp_congestion_ops can be used like
regular kernel tcp-cc through sysctl and setsockopt. e.g.
[root@arch-fb-vm1 bpf]# sysctl -a | egrep congestion
net.ipv4.tcp_allowed_congestion_control = reno cubic bpf_cubic
net.ipv4.tcp_available_congestion_control = reno bic cubic bpf_cubic
net.ipv4.tcp_congestion_control = bpf_cubic
There has been attempt to move the TCP CC to the user space
(e.g. CCP in TCP). The common arguments are faster turn around,
get away from long-tail kernel versions in production...etc,
which are legit points.
BPF has been the continuous effort to join both kernel and
userspace upsides together (e.g. XDP to gain the performance
advantage without bypassing the kernel). The recent BPF
advancements (in particular BTF-aware verifier, BPF trampoline,
BPF CO-RE...) made implementing kernel struct ops (e.g. tcp cc)
possible in BPF. It allows a faster turnaround for testing algorithm
in the production while leveraging the existing (and continue growing)
BPF feature/framework instead of building one specifically for
userspace TCP CC.
This patch allows write access to a few fields in tcp-sock
(in bpf_tcp_ca_btf_struct_access()).
The optional "get_info" is unsupported now. It can be added
later. One possible way is to output the info with a btf-id
to describe the content.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200109003508.3856115-1-kafai@fb.com
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-12-27
The following pull-request contains BPF updates for your *net-next* tree.
We've added 127 non-merge commits during the last 17 day(s) which contain
a total of 110 files changed, 6901 insertions(+), 2721 deletions(-).
There are three merge conflicts. Conflicts and resolution looks as follows:
1) Merge conflict in net/bpf/test_run.c:
There was a tree-wide cleanup c593642c8b ("treewide: Use sizeof_field() macro")
which gets in the way with b590cb5f80 ("bpf: Switch to offsetofend in
BPF_PROG_TEST_RUN"):
<<<<<<< HEAD
if (!range_is_zero(__skb, offsetof(struct __sk_buff, priority) +
sizeof_field(struct __sk_buff, priority),
=======
if (!range_is_zero(__skb, offsetofend(struct __sk_buff, priority),
>>>>>>> 7c8dce4b16
There are a few occasions that look similar to this. Always take the chunk with
offsetofend(). Note that there is one where the fields differ in here:
<<<<<<< HEAD
if (!range_is_zero(__skb, offsetof(struct __sk_buff, tstamp) +
sizeof_field(struct __sk_buff, tstamp),
=======
if (!range_is_zero(__skb, offsetofend(struct __sk_buff, gso_segs),
>>>>>>> 7c8dce4b16
Just take the one with offsetofend() /and/ gso_segs. Latter is correct due to
850a88cc40 ("bpf: Expose __sk_buff wire_len/gso_segs to BPF_PROG_TEST_RUN").
2) Merge conflict in arch/riscv/net/bpf_jit_comp.c:
(I'm keeping Bjorn in Cc here for a double-check in case I got it wrong.)
<<<<<<< HEAD
if (is_13b_check(off, insn))
return -1;
emit(rv_blt(tcc, RV_REG_ZERO, off >> 1), ctx);
=======
emit_branch(BPF_JSLT, RV_REG_T1, RV_REG_ZERO, off, ctx);
>>>>>>> 7c8dce4b16
Result should look like:
emit_branch(BPF_JSLT, tcc, RV_REG_ZERO, off, ctx);
3) Merge conflict in arch/riscv/include/asm/pgtable.h:
<<<<<<< HEAD
=======
#define VMALLOC_SIZE (KERN_VIRT_SIZE >> 1)
#define VMALLOC_END (PAGE_OFFSET - 1)
#define VMALLOC_START (PAGE_OFFSET - VMALLOC_SIZE)
#define BPF_JIT_REGION_SIZE (SZ_128M)
#define BPF_JIT_REGION_START (PAGE_OFFSET - BPF_JIT_REGION_SIZE)
#define BPF_JIT_REGION_END (VMALLOC_END)
/*
* Roughly size the vmemmap space to be large enough to fit enough
* struct pages to map half the virtual address space. Then
* position vmemmap directly below the VMALLOC region.
*/
#define VMEMMAP_SHIFT \
(CONFIG_VA_BITS - PAGE_SHIFT - 1 + STRUCT_PAGE_MAX_SHIFT)
#define VMEMMAP_SIZE BIT(VMEMMAP_SHIFT)
#define VMEMMAP_END (VMALLOC_START - 1)
#define VMEMMAP_START (VMALLOC_START - VMEMMAP_SIZE)
#define vmemmap ((struct page *)VMEMMAP_START)
>>>>>>> 7c8dce4b16
Only take the BPF_* defines from there and move them higher up in the
same file. Remove the rest from the chunk. The VMALLOC_* etc defines
got moved via 01f52e16b8 ("riscv: define vmemmap before pfn_to_page
calls"). Result:
[...]
#define __S101 PAGE_READ_EXEC
#define __S110 PAGE_SHARED_EXEC
#define __S111 PAGE_SHARED_EXEC
#define VMALLOC_SIZE (KERN_VIRT_SIZE >> 1)
#define VMALLOC_END (PAGE_OFFSET - 1)
#define VMALLOC_START (PAGE_OFFSET - VMALLOC_SIZE)
#define BPF_JIT_REGION_SIZE (SZ_128M)
#define BPF_JIT_REGION_START (PAGE_OFFSET - BPF_JIT_REGION_SIZE)
#define BPF_JIT_REGION_END (VMALLOC_END)
/*
* Roughly size the vmemmap space to be large enough to fit enough
* struct pages to map half the virtual address space. Then
* position vmemmap directly below the VMALLOC region.
*/
#define VMEMMAP_SHIFT \
(CONFIG_VA_BITS - PAGE_SHIFT - 1 + STRUCT_PAGE_MAX_SHIFT)
#define VMEMMAP_SIZE BIT(VMEMMAP_SHIFT)
#define VMEMMAP_END (VMALLOC_START - 1)
#define VMEMMAP_START (VMALLOC_START - VMEMMAP_SIZE)
[...]
Let me know if there are any other issues.
Anyway, the main changes are:
1) Extend bpftool to produce a struct (aka "skeleton") tailored and specific
to a provided BPF object file. This provides an alternative, simplified API
compared to standard libbpf interaction. Also, add libbpf extern variable
resolution for .kconfig section to import Kconfig data, from Andrii Nakryiko.
2) Add BPF dispatcher for XDP which is a mechanism to avoid indirect calls by
generating a branch funnel as discussed back in bpfconf'19 at LSF/MM. Also,
add various BPF riscv JIT improvements, from Björn Töpel.
3) Extend bpftool to allow matching BPF programs and maps by name,
from Paul Chaignon.
4) Support for replacing cgroup BPF programs attached with BPF_F_ALLOW_MULTI
flag for allowing updates without service interruption, from Andrey Ignatov.
5) Cleanup and simplification of ring access functions for AF_XDP with a
bonus of 0-5% performance improvement, from Magnus Karlsson.
6) Enable BPF JITs for x86-64 and arm64 by default. Also, final version of
audit support for BPF, from Daniel Borkmann and latter with Jiri Olsa.
7) Move and extend test_select_reuseport into BPF program tests under
BPF selftests, from Jakub Sitnicki.
8) Various BPF sample improvements for xdpsock for customizing parameters
to set up and benchmark AF_XDP, from Jay Jayatheerthan.
9) Improve libbpf to provide a ulimit hint on permission denied errors.
Also change XDP sample programs to attach in driver mode by default,
from Toke Høiland-Jørgensen.
10) Extend BPF test infrastructure to allow changing skb mark from tc BPF
programs, from Nikita V. Shirokov.
11) Optimize prologue code sequence in BPF arm32 JIT, from Russell King.
12) Fix xdp_redirect_cpu BPF sample to manually attach to tracepoints after
libbpf conversion, from Jesper Dangaard Brouer.
13) Minor misc improvements from various others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all XDP maps that can be used with bpf_redirect_map() tracks
entries to be flushed in a global fashion, there is not need to track
that the map has changed and flush from xdp_do_generic_map()
anymore. All entries will be flushed in xdp_do_flush_map().
This means that the map_to_flush can be removed, and the corresponding
checks. Moving the flush logic to one place, xdp_do_flush_map(), give
a bulking behavior and performance boost.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20191219061006.21980-8-bjorn.topel@gmail.com
This commit adds a BPF dispatcher for XDP. The dispatcher is updated
from the XDP control-path, dev_xdp_install(), and used when an XDP
program is run via bpf_prog_run_xdp().
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191213175112.30208-4-bjorn.topel@gmail.com
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
For the case where the interpreter is compiled out or when the prog is jited
it is completely unnecessary to set the BPF insn pages as read-only. In fact,
on frequent churn of BPF programs, it could lead to performance degradation of
the system over time since it would break the direct map down to 4k pages when
calling set_memory_ro() for the insn buffer on x86-64 / arm64 and there is no
reverse operation. Thus, avoid breaking up large pages for data maps, and only
limit this to the module range used by the JIT where it is necessary to set
the image read-only and executable.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191129222911.3710-1-daniel@iogearbox.net
Add a definition of bpf_jit_blinding_enabled() when CONFIG_BPF_JIT is not set
in order to fix a recent build regression:
[...]
CC kernel/bpf/verifier.o
CC kernel/bpf/inode.o
kernel/bpf/verifier.c: In function ‘fixup_bpf_calls’:
kernel/bpf/verifier.c:9132:25: error: implicit declaration of function ‘bpf_jit_blinding_enabled’; did you mean ‘bpf_jit_kallsyms_enabled’? [-Werror=implicit-function-declaration]
9132 | bool expect_blinding = bpf_jit_blinding_enabled(prog);
| ^~~~~~~~~~~~~~~~~~~~~~~~
| bpf_jit_kallsyms_enabled
CC kernel/bpf/helpers.o
CC kernel/bpf/hashtab.o
[...]
Fixes: d2e4c1e6c2 ("bpf: Constant map key tracking for prog array pokes")
Reported-by: Jakub Sitnicki <jakub@cloudflare.com>
Reported-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/40baf8f3507cac4851a310578edfb98ce73b5605.1574541375.git.daniel@iogearbox.net
Add initial poke table data structures and management to the BPF
prog that can later be used by JITs. Also add an instance of poke
specific data for tail call maps; plan for later work is to extend
this also for BPF static keys.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/1db285ec2ea4207ee0455b3f8e191a4fc58b9ade.1574452833.git.daniel@iogearbox.net
Currently passing alignment greater than 4 to bpf_jit_binary_alloc does
not work: in such cases it silently aligns only to 4 bytes.
On s390, in order to load a constant from memory in a large (>512k) BPF
program, one must use lgrl instruction, whose memory operand must be
aligned on an 8-byte boundary.
This patch makes it possible to request 8-byte alignment from
bpf_jit_binary_alloc, and also makes it issue a warning when an
unsupported alignment is requested.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191115123722.58462-1-iii@linux.ibm.com
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
syzkaller managed to trigger the following crash:
[...]
BUG: unable to handle page fault for address: ffffc90001923030
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD aa551067 P4D aa551067 PUD aa552067 PMD a572b067 PTE 80000000a1173163
Oops: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 7982 Comm: syz-executor912 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:bpf_jit_binary_hdr include/linux/filter.h:787 [inline]
RIP: 0010:bpf_get_prog_addr_region kernel/bpf/core.c:531 [inline]
RIP: 0010:bpf_tree_comp kernel/bpf/core.c:600 [inline]
RIP: 0010:__lt_find include/linux/rbtree_latch.h:115 [inline]
RIP: 0010:latch_tree_find include/linux/rbtree_latch.h:208 [inline]
RIP: 0010:bpf_prog_kallsyms_find kernel/bpf/core.c:674 [inline]
RIP: 0010:is_bpf_text_address+0x184/0x3b0 kernel/bpf/core.c:709
[...]
Call Trace:
kernel_text_address kernel/extable.c:147 [inline]
__kernel_text_address+0x9a/0x110 kernel/extable.c:102
unwind_get_return_address+0x4c/0x90 arch/x86/kernel/unwind_frame.c:19
arch_stack_walk+0x98/0xe0 arch/x86/kernel/stacktrace.c:26
stack_trace_save+0xb6/0x150 kernel/stacktrace.c:123
save_stack mm/kasan/common.c:69 [inline]
set_track mm/kasan/common.c:77 [inline]
__kasan_kmalloc+0x11c/0x1b0 mm/kasan/common.c:510
kasan_slab_alloc+0xf/0x20 mm/kasan/common.c:518
slab_post_alloc_hook mm/slab.h:584 [inline]
slab_alloc mm/slab.c:3319 [inline]
kmem_cache_alloc+0x1f5/0x2e0 mm/slab.c:3483
getname_flags+0xba/0x640 fs/namei.c:138
getname+0x19/0x20 fs/namei.c:209
do_sys_open+0x261/0x560 fs/open.c:1091
__do_sys_open fs/open.c:1115 [inline]
__se_sys_open fs/open.c:1110 [inline]
__x64_sys_open+0x87/0x90 fs/open.c:1110
do_syscall_64+0xf7/0x1c0 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
[...]
After further debugging it turns out that we walk kallsyms while in parallel
we tear down a BPF program which contains subprograms that have been JITed
though the program itself has not been fully exposed and is eventually bailing
out with error.
The bpf_prog_kallsyms_del_subprogs() in bpf_prog_load()'s error path removes
the symbols, however, bpf_prog_free() tears down the JIT memory too early via
scheduled work. Instead, it needs to properly respect RCU grace period as the
kallsyms walk for BPF is under RCU.
Fix it by refactoring __bpf_prog_put()'s tear down and reuse it in our error
path where we defer final destruction when we have subprogs in the program.
Fixes: 7d1982b4e3 ("bpf: fix panic in prog load calls cleanup")
Fixes: 1c2a088a66 ("bpf: x64: add JIT support for multi-function programs")
Reported-by: syzbot+710043c5d1d5b5013bc7@syzkaller.appspotmail.com
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: syzbot+710043c5d1d5b5013bc7@syzkaller.appspotmail.com
Link: https://lore.kernel.org/bpf/55f6367324c2d7e9583fa9ccf5385dcbba0d7a6e.1571752452.git.daniel@iogearbox.net
Pointer to BTF object is a pointer to kernel object or NULL.
The memory access in the interpreter has to be done via probe_kernel_read
to avoid page faults.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20191016032505.2089704-9-ast@kernel.org
When pahole converts dwarf to btf it emits only used types.
Wrap existing bpf helper functions into typedef and use it in
typecast to make gcc emits this type into dwarf.
Then pahole will convert it to btf.
The "btf_#name_of_helper" types will be used to figure out
types of arguments of bpf helpers.
The generated code before and after is the same.
Only dwarf and btf sections are different.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20191016032505.2089704-3-ast@kernel.org
"ctx:file_pos sysctl:read write ok" fails on s390 with "Read value !=
nux". This is because verifier rewrites a complete 32-bit
bpf_sysctl.file_pos update to a partial update of the first 32 bits of
64-bit *bpf_sysctl_kern.ppos, which is not correct on big-endian
systems.
Fix by using an offset on big-endian systems.
Ditto for bpf_sysctl.file_pos reads. Currently the test does not detect
a problem there, since it expects to see 0, which it gets with high
probability in error cases, so change it to seek to offset 3 and expect
3 in bpf_sysctl.file_pos.
Fixes: e1550bfe0d ("bpf: Add file_pos field to bpf_sysctl ctx")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20190816105300.49035-1-iii@linux.ibm.com/
The very first check in test_pkt_md_access is failing on s390, which
happens because loading a part of a struct __sk_buff field produces
an incorrect result.
The preprocessed code of the check is:
{
__u8 tmp = *((volatile __u8 *)&skb->len +
((sizeof(skb->len) - sizeof(__u8)) / sizeof(__u8)));
if (tmp != ((*(volatile __u32 *)&skb->len) & 0xFF)) return 2;
};
clang generates the following code for it:
0: 71 21 00 03 00 00 00 00 r2 = *(u8 *)(r1 + 3)
1: 61 31 00 00 00 00 00 00 r3 = *(u32 *)(r1 + 0)
2: 57 30 00 00 00 00 00 ff r3 &= 255
3: 5d 23 00 1d 00 00 00 00 if r2 != r3 goto +29 <LBB0_10>
Finally, verifier transforms it to:
0: (61) r2 = *(u32 *)(r1 +104)
1: (bc) w2 = w2
2: (74) w2 >>= 24
3: (bc) w2 = w2
4: (54) w2 &= 255
5: (bc) w2 = w2
The problem is that when verifier emits the code to replace a partial
load of a struct __sk_buff field (*(u8 *)(r1 + 3)) with a full load of
struct sk_buff field (*(u32 *)(r1 + 104)), an optional shift and a
bitwise AND, it assumes that the machine is little endian and
incorrectly decides to use a shift.
Adjust shift count calculation to account for endianness.
Fixes: 31fd85816d ("bpf: permits narrower load from bpf program context fields")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Rename bpf_ctx_wide_store_ok to bpf_ctx_wide_access_ok to indicate
that it can be used for both loads and stores.
Cc: Yonghong Song <yhs@fb.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Since commit cd17d77705 ("bpf/tools: sync bpf.h") clang decided
that it can do a single u64 store into user_ip6[2] instead of two
separate u32 ones:
# 17: (18) r2 = 0x100000000000000
# ; ctx->user_ip6[2] = bpf_htonl(DST_REWRITE_IP6_2);
# 19: (7b) *(u64 *)(r1 +16) = r2
# invalid bpf_context access off=16 size=8
>From the compiler point of view it does look like a correct thing
to do, so let's support it on the kernel side.
Credit to Andrii Nakryiko for a proper implementation of
bpf_ctx_wide_store_ok.
Cc: Andrii Nakryiko <andriin@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Fixes: cd17d77705 ("bpf/tools: sync bpf.h")
Reported-by: kernel test robot <rong.a.chen@intel.com>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The bpf_redirect_map() helper used by XDP programs doesn't return any
indication of whether it can successfully redirect to the map index it was
given. Instead, BPF programs have to track this themselves, leading to
programs using duplicate maps to track which entries are populated in the
devmap.
This patch fixes this by moving the map lookup into the bpf_redirect_map()
helper, which makes it possible to return failure to the eBPF program. The
lower bits of the flags argument is used as the return code, which means
that existing users who pass a '0' flag argument will get XDP_ABORTED.
With this, a BPF program can check the return code from the helper call and
react by, for instance, substituting a different redirect. This works for
any type of map used for redirect.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The bpf_redirect_info struct has an 'ifindex' member which was named back
when the redirects could only target egress interfaces. Now that we can
also redirect to sockets and CPUs, this is a bit misleading, so rename the
member to tgt_index.
Reorder the struct members so we can have 'tgt_index' and 'tgt_value' next
to each other in a subsequent patch.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Implement new BPF_PROG_TYPE_CGROUP_SOCKOPT program type and
BPF_CGROUP_{G,S}ETSOCKOPT cgroup hooks.
BPF_CGROUP_SETSOCKOPT can modify user setsockopt arguments before
passing them down to the kernel or bypass kernel completely.
BPF_CGROUP_GETSOCKOPT can can inspect/modify getsockopt arguments that
kernel returns.
Both hooks reuse existing PTR_TO_PACKET{,_END} infrastructure.
The buffer memory is pre-allocated (because I don't think there is
a precedent for working with __user memory from bpf). This might be
slow to do for each {s,g}etsockopt call, that's why I've added
__cgroup_bpf_prog_array_is_empty that exits early if there is nothing
attached to a cgroup. Note, however, that there is a race between
__cgroup_bpf_prog_array_is_empty and BPF_PROG_RUN_ARRAY where cgroup
program layout might have changed; this should not be a problem
because in general there is a race between multiple calls to
{s,g}etsocktop and user adding/removing bpf progs from a cgroup.
The return code of the BPF program is handled as follows:
* 0: EPERM
* 1: success, continue with next BPF program in the cgroup chain
v9:
* allow overwriting setsockopt arguments (Alexei Starovoitov):
* use set_fs (same as kernel_setsockopt)
* buffer is always kzalloc'd (no small on-stack buffer)
v8:
* use s32 for optlen (Andrii Nakryiko)
v7:
* return only 0 or 1 (Alexei Starovoitov)
* always run all progs (Alexei Starovoitov)
* use optval=0 as kernel bypass in setsockopt (Alexei Starovoitov)
(decided to use optval=-1 instead, optval=0 might be a valid input)
* call getsockopt hook after kernel handlers (Alexei Starovoitov)
v6:
* rework cgroup chaining; stop as soon as bpf program returns
0 or 2; see patch with the documentation for the details
* drop Andrii's and Martin's Acked-by (not sure they are comfortable
with the new state of things)
v5:
* skip copy_to_user() and put_user() when ret == 0 (Martin Lau)
v4:
* don't export bpf_sk_fullsock helper (Martin Lau)
* size != sizeof(__u64) for uapi pointers (Martin Lau)
* offsetof instead of bpf_ctx_range when checking ctx access (Martin Lau)
v3:
* typos in BPF_PROG_CGROUP_SOCKOPT_RUN_ARRAY comments (Andrii Nakryiko)
* reverse christmas tree in BPF_PROG_CGROUP_SOCKOPT_RUN_ARRAY (Andrii
Nakryiko)
* use __bpf_md_ptr instead of __u32 for optval{,_end} (Martin Lau)
* use BPF_FIELD_SIZEOF() for consistency (Martin Lau)
* new CG_SOCKOPT_ACCESS macro to wrap repeated parts
v2:
* moved bpf_sockopt_kern fields around to remove a hole (Martin Lau)
* aligned bpf_sockopt_kern->buf to 8 bytes (Martin Lau)
* bpf_prog_array_is_empty instead of bpf_prog_array_length (Martin Lau)
* added [0,2] return code check to verifier (Martin Lau)
* dropped unused buf[64] from the stack (Martin Lau)
* use PTR_TO_SOCKET for bpf_sockopt->sk (Martin Lau)
* dropped bpf_target_off from ctx rewrites (Martin Lau)
* use return code for kernel bypass (Martin Lau & Andrii Nakryiko)
Cc: Andrii Nakryiko <andriin@fb.com>
Cc: Martin Lau <kafai@fb.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Allows cgroup inet skb programs to return values in the range [0, 3].
The second bit is used to deterine if congestion occurred and higher
level protocol should decrease rate. E.g. TCP would call tcp_enter_cwr()
The bpf_prog must set expected_attach_type to BPF_CGROUP_INET_EGRESS
at load time if it uses the new return values (i.e. 2 or 3).
The expected_attach_type is currently not enforced for
BPF_PROG_TYPE_CGROUP_SKB. e.g Meaning the current bpf_prog with
expected_attach_type setting to BPF_CGROUP_INET_EGRESS can attach to
BPF_CGROUP_INET_INGRESS. Blindly enforcing expected_attach_type will
break backward compatibility.
This patch adds a enforce_expected_attach_type bit to only
enforce the expected_attach_type when it uses the new
return value.
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
After previous patches, verifier will mark a insn if it really needs zero
extension on dst_reg.
It is then for back-ends to decide how to use such information to eliminate
unnecessary zero extension code-gen during JIT compilation.
One approach is verifier insert explicit zero extension for those insns
that need zero extension in a generic way, JIT back-ends then do not
generate zero extension for sub-register write at default.
However, only those back-ends which do not have hardware zero extension
want this optimization. Back-ends like x86_64 and AArch64 have hardware
zero extension support that the insertion should be disabled.
This patch introduces new target hook "bpf_jit_needs_zext" which returns
false at default, meaning verifier zero extension insertion is disabled at
default. A back-end could override this hook to return true if it doesn't
have hardware support and want verifier insert zero extension explicitly.
Offload targets do not use this native target hook, instead, they could
get the optimization results using bpf_prog_offload_ops.finalize.
NOTE: arches could have diversified features, it is possible for one arch
to have hardware zero extension support for some sub-register write insns
but not for all. For example, PowerPC, SPARC have zero extended loads, but
not for alu32. So when verifier zero extension insertion enabled, these JIT
back-ends need to peephole insns to remove those zero extension inserted
for insn that actually has hardware zero extension support. The peephole
could be as simple as looking the next insn, if it is a special zero
extension insn then it is safe to eliminate it if the current insn has
hardware zero extension support.
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The encoding for this new variant is based on BPF_X format. "imm" field was
0 only, now it could be 1 which means doing zero extension unconditionally
.code = BPF_ALU | BPF_MOV | BPF_X
.dst_reg = DST
.src_reg = SRC
.imm = 1
We use this new form for doing zero extension for which verifier will
guarantee SRC == DST.
Implications on JIT back-ends when doing code-gen for
BPF_ALU | BPF_MOV | BPF_X:
1. No change if hardware already does zero extension unconditionally for
sub-register write.
2. Otherwise, when seeing imm == 1, just generate insns to clear high
32-bit. No need to generate insns for the move because when imm == 1,
dst_reg is the same as src_reg at the moment.
Interpreter doesn't need change as well. It is doing unconditionally zero
extension for mov32 already.
One helper macro BPF_ZEXT_REG is added to help creating zero extension
insn using this new mov32 variant.
One helper function insn_is_zext is added for checking one insn is an
zero extension on dst. This will be widely used by a few JIT back-ends in
later patches in this set.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
Use new flag VM_FLUSH_RESET_PERMS for handling freeing of special
permissioned memory in vmalloc and remove places where memory was set RW
before freeing which is no longer needed. Don't track if the memory is RO
anymore because it is now tracked in vmalloc.
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <akpm@linux-foundation.org>
Cc: <ard.biesheuvel@linaro.org>
Cc: <deneen.t.dock@intel.com>
Cc: <kernel-hardening@lists.openwall.com>
Cc: <kristen@linux.intel.com>
Cc: <linux_dti@icloud.com>
Cc: <will.deacon@arm.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190426001143.4983-19-namit@vmware.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When modules and BPF filters are loaded, there is a time window in
which some memory is both writable and executable. An attacker that has
already found another vulnerability (e.g., a dangling pointer) might be
able to exploit this behavior to overwrite kernel code. Prevent having
writable executable PTEs in this stage.
In addition, avoiding having W+X mappings can also slightly simplify the
patching of modules code on initialization (e.g., by alternatives and
static-key), as would be done in the next patch. This was actually the
main motivation for this patch.
To avoid having W+X mappings, set them initially as RW (NX) and after
they are set as RO set them as X as well. Setting them as executable is
done as a separate step to avoid one core in which the old PTE is cached
(hence writable), and another which sees the updated PTE (executable),
which would break the W^X protection.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Suggested-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <akpm@linux-foundation.org>
Cc: <ard.biesheuvel@linaro.org>
Cc: <deneen.t.dock@intel.com>
Cc: <kernel-hardening@lists.openwall.com>
Cc: <kristen@linux.intel.com>
Cc: <linux_dti@icloud.com>
Cc: <will.deacon@arm.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Link: https://lkml.kernel.org/r/20190426001143.4983-12-namit@vmware.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
