DMA initialization error handling is not properly implemented in the
driver.
Fix DMA initialization error handling by:
- moving TX DMA descriptor request error handling in a new dedicated
fallback_err label
- adding error handling to TX DMA descriptor submission
- adding error handling to RX DMA descriptor submission
This patch depends on '24832ca3ee85 ("tty: serial: stm32-usart: Remove set
but unused 'cookie' variables")' which unfortunately doesn't include a
"Fixes" tag.
Fixes: 3489187204 ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210106162203.28854-2-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/stm32-usart.c: In function ‘stm32_transmit_chars_dma’:
drivers/tty/serial/stm32-usart.c:353:15: warning: variable ‘cookie’ set but not used [-Wunused-but-set-variable]
drivers/tty/serial/stm32-usart.c: In function ‘stm32_of_dma_rx_probe’:
drivers/tty/serial/stm32-usart.c:1090:15: warning: variable ‘cookie’ set but not used [-Wunused-but-set-variable]
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Gerald Baeza <gerald.baeza@st.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-29-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the STM32 does support RS485 drive-enable control within the
UART IP itself, some systems have the drive-enable line connected
to a pin which cannot be pinmuxed as RTS. Add support for toggling
the RTS GPIO line using the modem control GPIOs to provide at least
some sort of emulation.
Fixes: 7df5081cbf ("serial: stm32: Add RS485 RTS GPIO control")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
Link: https://lore.kernel.org/r/20200831171045.205691-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
stm32_init_port() of the stm32-usart may trigger a warning in
platform_get_irq() when the device tree specifies no wakeup interrupt.
The wakeup interrupt is usually a board-specific GPIO and the driver
functions correctly in its absence. The mainline stm32mp151.dtsi does
not specify it, so all mainline device trees trigger an unnecessary
kernel warning. Use of platform_get_irq_optional() avoids this.
Fixes: 2c58e56096 ("serial: stm32: fix the get_irq error case")
Signed-off-by: Holger Assmann <h.assmann@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200813152757.32751-1-h.assmann@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the STM32 does support RS485 drive-enable control within the
UART IP itself, some systems have the drive-enable line connected
to a pin which cannot be pinmuxed as RTS. Add support for toggling
the RTS GPIO line using the modem control GPIOs to provide at least
some sort of emulation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-stm32@st-md-mailman.stormreply.com
Link: https://lore.kernel.org/r/20200725144947.537007-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support of generic DT binding for annoucing RTS/CTS lines. The initial
binding 'st,hw-flow-control' is not needed anymore since generic binding
is available, but is kept for backward compatibility.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Link: https://lore.kernel.org/r/20200520133932.30441-3-erwan.leray@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to display console messages in low power mode, console pins
must be kept active after suspend call.
Initial patch "serial: stm32: add support for no_console_suspend" was part
of "STM32 usart power improvement" series, but as dependancy to
console_suspend pinctl state has been removed to fit with Rob comment [1],
this patch has no more dependancy with any other patch of this series.
[1] https://lkml.org/lkml/2019/7/9/451
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Link: https://lore.kernel.org/r/20200519094104.27082-1-erwan.leray@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're about to amend uart_get_rs485_mode() to support a GPIO pin for
rs485 bus termination. Retrieving the GPIO descriptor may fail, so
allow uart_get_rs485_mode() to return an errno and change all callers
to check for failure.
The GPIO descriptor is going to be stored in struct uart_port. Pass
that struct to uart_get_rs485_mode() in lieu of a struct device and
struct serial_rs485, both of which are directly accessible from struct
uart_port.
A few drivers call uart_get_rs485_mode() before setting the struct
device pointer in struct uart_port. Shuffle those calls around where
necessary.
[Heiko Stuebner did the ar933x_uart.c portion, hence his Signed-off-by.]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/271e814af4b0db3bffbbb74abf2b46b75add4516.1589285873.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STM32 UART controllers have the built in modem control support using
dedicated gpios which can be enabled using 'st,hw-flow-ctrl' flag in DT.
But there might be cases where the board design need to use different
gpios for modem control.
For supporting such cases, this commit adds modem control gpio support
to STM32 UART controller using mctrl_gpio driver.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Link: https://lore.kernel.org/r/20200420170204.24541-3-mani@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-45-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interrupt clear flag register is a "write 1 to clear" register.
So, only writing ones allows to clear flags:
- Replace buggy stm32_clr_bits() by a simple write to clear error flags
- Replace useless read/modify/write stm32_set_bits() routine by a
simple write to clear TC (transfer complete) flag.
Fixes: 4f01d833fd ("serial: stm32: fix rx error handling")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1574323849-1909-1-git-send-email-fabrice.gasnier@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-45-swboyd@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Select either pinctrl sleep state in suspend function or default state in
resume function.
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Link: https://lore.kernel.org/r/1560433800-12255-4-git-send-email-erwan.leray@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds a flush of RX and TX FIFOs, and fixes some errors:
- adds RX FIFO flush in startup fonction
- removes the useless transmitter enabling in startup fonction
(e.g. receiver only, see Documentation/serial/driver)
- configures FIFO threshold before enabling it, rather than after
- flushes both TX and RX in set_termios function
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds the support of RX FIFO threshold in order to improve the RX FIFO
management.
This is done by enabling fifo threshold interrupt, instead of relying
on rx empty/fifo not full irq. That basically generates one irq/char
currently. With this patch:
- RXCFG is set to half fifo size (e.g. 16/2 = 8 data for a 16 data depth
FIFO)
- irq rate may be reduced by up to 1/RXCFG, e.g. 1 over 8 with current
RXCFG setting.
- Receiver timeout is used to gather chars when FIFO threshold isn't
reached.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds the support of TX FIFO threshold in order to improve the TX FIFO
management:
- TX FIFO threshold irq enabling (instead of relying on tx empty / fifo
not full irq that generates one irq/char)
- TXCFG is set to half fifo size (e.g. 16/2 = 8 data for a 16 data depth
FIFO)
- irq rate may be reduced by up to 1/TXCFG, e.g. 1 over 8 with current
TXCFG setting.
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improves PIO transmission:
- Replaces the FIFO filling per character by a filling per blocks of
characters, which provides better performances
- Replaces the active waiting loop by TX empty interrupt dynamic handling.
TXE interrupt is now enabled when data has to be sent (ie when
uart_circ is not empty), and inhibited when there is no more data to
send (ie when uart_circ is empty).
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support of RX timeout interrupts to limit the number of interrupts.
RX timeout is a number of bits (baud clock cycles) without
transmission seen in the receiver. One character is used as an arbitrary
RX timeout value.
If parity is enabled, the number of bits has to include parity bit.
Signed-off-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c70669ecef as it
breaks the build.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Bich Hemon <bich.hemon@st.com>
Cc: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove spin_lock_irqsave in stm32_config_rs485, it cause recursive locking.
Already locked in uart_set_rs485_config.
Fixes: 1bcda09d29 ("serial: stm32: add support for RS485 hardware control mode")
Signed-off-by: Borut Seljak <borut.seljak@t-2.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix sparse warning:
drivers/tty/serial/stm32-usart.c:603:14: warning:
symbol 'stm32_get_databits' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Select either pinctrl sleep state in suspend function or default state in
resume function.
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checks the returned values of platform_get_irq() for both required
"event" and optional "wakeup" IRQs during probe. This allows the driver
probe to be deferred if needed.
Removes redundant checks for 'cfg.has_wakeup'.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds a check on the Transmission Complete bit status before closing the
com port. Prevents the port closure before the end of the transmission.
TC poll loop is moved from stm32_tx_dma_complete to stm32_shutdown
routine, in order to check TC before shutdown in both dma and
PIO tx modes.
TC clear is added in stm32_transmit_char routine, in order to be cleared
before transmitting in both dma and PIO tx modes.
Fixes: 3489187204 ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disables the tx irq when the transmission is ended and updates stop_tx
conditions for code cleanup.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fixes a rx data error when data length < 8 bits and parity is enabled.
RDR register MSB is used for parity bit reception.
- Adds a mask to ignore MSB when data is get from RDR.
Fixes: 3489187204 ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fixes parity and framing error bit by clearing parity and framing error
flag. The current implementation doesn't clear the error bits when an
error is detected.
- Fixes the incorrect name of framing error clearing flag in header file.
- Fixes misalignement between data frame and errors status. The status
read for "n" frame was the status of "n+1" frame".
- Fixes break detection was not triggered by the expected register.
Fixes: 48a6092fb4 ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STM32 supports either:
- 8 and 9 bits word length (including parity bit) for stm32f4 compatible
devices
- 7, 8 and 9 bits word length (including parity bit) for stm32f7 and
stm32h7 compatible devices.
As a consequence STM32 supports the following termios configurations:
- CS7 with parity bit, and CS8 (with or without parity bit) for stm32f4
compatible devices.
- CS6 with parity bit, CS7 and CS8 (with or without parity bit) for
stm32f7 and stm32h7 compatible devices.
This patch is fixing word length by configuring correctly the SoC with
supported configurations.
Fixes: ada8618ff3 ("serial: stm32: adding support for stm32f7")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all tty files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/tty files files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: "Uwe Kleine-König" <kernel@pengutronix.de>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to duplicate a flag which IRQ core takes care of.
Replace custom flag by IRQ core API that retrieves its state.
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds fifo mode support for rx and tx.
A fifo configuration is set in each port structure.
Add has_fifo flag to usart configuration to use fifo only when possible.
Signed-off-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for wake-up from low power modes. This extends stm32f7.
Introduce new compatible for stm32h7 to manage wake-up capability.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement support of RTS in USART control register
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct management of multi-ports. Each port has
its own last residue value and its own alias.
Signed-off-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We get 2 warnings when building kernel with W=1:
drivers/tty/serial/stm32-usart.c:63:5: warning: no previous prototype for 'stm32_pending_rx' [-Wmissing-prototypes]
drivers/tty/serial/stm32-usart.c:88:15: warning: no previous prototype for 'stm32_get_char' [-Wmissing-prototypes]
In fact, these two functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
So this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building this driver with a 64-bit dma_addr_t type results in
a compiler warning:
drivers/tty/serial/stm32-usart.c: In function 'stm32_of_dma_rx_probe':
drivers/tty/serial/stm32-usart.c:746:20: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
drivers/tty/serial/stm32-usart.c: In function 'stm32_of_dma_tx_probe':
drivers/tty/serial/stm32-usart.c:818:20: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
While the type conversion here is harmless, this hints at a different
problem: we pass an __iomem pointer into a DMA engine, which expects
a phys_addr_t. This happens to work because stm32 has no MMU and
ioremap() is an identity mapping here, but it's still an incorrect
API use. Using dma_addr_t is doubly wrong here, because that would
be the result of dma_map_single() rather than the physical address.
Using the mapbase instead fixes multiple issues:
- the warning is gone
- we don't go through ioremap in error
- the cast is gone, making it use the correct resource_size_t/phys_addr_t
type in the process.
Fixes: 3489187204 ("serial: stm32: adding dma support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds dma mode support for rx and tx
with pio mode as fallback in case of dma error.
Signed-off-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keep the clock enabled at the end of stm32_init_port
but disable it in stm32_serial_remove.
Note that stm32_pm function is there to manage the
clock at runtime.
Signed-off-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
