After upgrading from 5.16 to 6.1, our board with a MAX14830 started
producing lots of garbage data over UART. Bisection pointed out commit
285e76fc04 as the culprit. That patch tried to replace hand-written
code which I added in 2b4bac48c1 ("serial: max310x: Use batched reads
when reasonably safe") with the generic regmap infrastructure for
batched operations.
Unfortunately, the `regmap_raw_read` and `regmap_raw_write` which were
used are actually functions which perform IO over *multiple* registers.
That's not what is needed for accessing these Tx/Rx FIFOs; the
appropriate functions are the `_noinc_` versions, not the `_raw_` ones.
Fix this regression by using `regmap_noinc_read()` and
`regmap_noinc_write()` along with the necessary `regmap_config` setup;
with this patch in place, our board communicates happily again. Since
our board uses SPI for talking to this chip, the I2C part is completely
untested.
Fixes: 285e76fc04 ("serial: max310x: use regmap methods for SPI batch operations")
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://lore.kernel.org/r/79db8e82aadb0e174bc82b9996423c3503c8fb37.1680732084.git.jan.kundrat@cesnet.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While rebinding a uart device in a loop I noticed we may see a tx related
race on uart_remove_one_port():
uart_write from n_tty_write
n_tty_write from file_tty_write.constprop.0
file_tty_write.constprop.0 from vfs_write
vfs_write from ksys_write
ksys_write from ret_fast_syscall
Let's disallow tx on port->UPF_DEAD. This flag gets set before we start
tearing down the port in uart_remove_one_port().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230419115423.59957-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we unbind a serial port hardware specific 8250 driver, the generic
serial8250 driver takes over the port. After that we see an oops about 10
seconds later. This can produce the following at least on some TI SoCs:
Unhandled fault: imprecise external abort (0x1406)
Internal error: : 1406 [#1] SMP ARM
Turns out that we may still have the serial port hardware specific driver
port->pm in use, and serial8250_pm() tries to call it after the port
specific driver is gone:
serial8250_pm [8250_base] from uart_change_pm+0x54/0x8c [serial_base]
uart_change_pm [serial_base] from uart_hangup+0x154/0x198 [serial_base]
uart_hangup [serial_base] from __tty_hangup.part.0+0x328/0x37c
__tty_hangup.part.0 from disassociate_ctty+0x154/0x20c
disassociate_ctty from do_exit+0x744/0xaac
do_exit from do_group_exit+0x40/0x8c
do_group_exit from __wake_up_parent+0x0/0x1c
Let's fix the issue by calling serial8250_set_defaults() in
serial8250_unregister_port(). This will set the port back to using
the serial8250 default functions, and sets the port->pm to point to
serial8250_pm.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230418101407.12403-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An 8250 UART configured as a wake-up source would not have reported
itself through sysfs as being the source of wake-up, correct that.
Fixes: b3b708fa27 ("wake up from a serial port")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230414170241.2016255-1-f.fainelli@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For lpuart32 platforms, UARTMODIR register is used instead of UARTMODEM.
So here should configure the corresponding UARTMODIR register bits to
avoid confusion.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230414022111.20896-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the fls function definition provided below, we should not
subtract 1 to obtain the correct buffer length:
fls(0) = 0, fls(1) = 1, fls(0x80000000) = 32.
Fixes: 5887ad43ee ("tty: serial: fsl_lpuart: Use cyclic DMA for Rx")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20230410195555.1003900-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RS485 multipoint addressing support for some reason added a new
ADDRB termios cflag which is (only!) updated from one of the RS485
ioctls.
Make sure to take the termios rw semaphore for the right ioctl (i.e.
set, not get).
Fixes: ae50bb2752 ("serial: take termios_rwsem for ->rs485_config() & pass termios as param")
Cc: stable@vger.kernel.org # 6.0
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20230412124811.11217-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of converting RISC-V SOC_FOO symbols to ARCH_FOO to match the
use of such symbols on other architectures, convert the SiFive serial
driver Kconfig entries from the SOC_ symbols to ARCH_ instead.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230406-carnival-aspirate-fcf69a30078c@spud
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In synclinc_gt, the flag_buf is allocated, zeroed and passed to ldisc's
receive_buf(). It is never written to, so it serves as a dummy buffer.
That's unneeded because all ldiscs accept NULL as flags. That NULL
resolves to the TTY_NORMAL flag.
So drop all this nonsense.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230420093530.13133-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* use memcpy() instead of the loop (removes c variable)
* use remaining parameter directly (removes chunk variable)
The code is simpler and easier to follow.
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230420093514.13055-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function gsmld_open() contains a redundant assignment of gsm->encoding.
The same value of GSM_ADV_OPT is already assigned to it during the
initialization of the struct in gsm_alloc_mux() a few lines earlier.
Fix this by removing the redundant second assignment of gsm->encoding in
gsmld_open().
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230420085017.7314-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small tty and serial driver fixes for some reported
problems:
- fsl_uart driver bugfixes
- sh-sci serial driver bugfixes
- renesas serial driver DT binding bugfixes
- 8250 DMA bugfix
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iGwEABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZDFTtg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynImACXZSsiSzuMqAoEisjLfcb7bPovvQCfd5FntU3K
h6JE0Y44gi6WS9iWYHU=
=jDa+
-----END PGP SIGNATURE-----
Merge tag 'tty-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty and serial driver fixes for some reported
problems:
- fsl_uart driver bugfixes
- sh-sci serial driver bugfixes
- renesas serial driver DT binding bugfixes
- 8250 DMA bugfix
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: sh-sci: Fix Rx on RZ/G2L SCI
tty: serial: fsl_lpuart: fix crash in lpuart_uport_is_active
tty: serial: fsl_lpuart: avoid checking for transfer complete when UARTCTRL_SBK is asserted in lpuart32_tx_empty
serial: 8250: Prevent starting up DMA Rx on THRI interrupt
dt-bindings: serial: renesas,scif: Fix 4th IRQ for 4-IRQ SCIFs
tty: serial: sh-sci: Fix transmit end interrupt handler
With linux/acpi.h no longer implicitly including of.h, add an explicit
include of of.h to fix the following error:
drivers/tty/serial/8250/8250_tegra.c:68:15: error: implicit declaration of function 'of_alias_get_id' [-Werror=implicit-function-declaration]
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix typo in LEGACY_TIOCSTI Kconfig description
There is a stray ' in the description before the Y. It appears this was
meant as a quote for the 'Y'. However, it is more common to use
unquoted Y in Kconfig descriptions.
Signed-off-by: Hanno Böck <hanno@hboeck.de>
Link: https://lore.kernel.org/r/20230330213557.60cf1533.hanno@hboeck.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver core allows for struct class to be in read-only
memory, move the tty_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Cc: "Ilpo Järvinen" <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/2023040250-landowner-unfitted-11f4@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the fixes in here for testing, as well as the driver core
changes for documentation updates to build on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCI IP on RZ/G2L alike SoCs do not need regshift compared to other SCI
IPs on the SH platform. Currently, it does regshift and configuring Rx
wrongly. Drop adding regshift for RZ/G2L alike SoCs.
Fixes: dfc80387ae ("serial: sh-sci: Compute the regshift value for SCI ports")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230321114753.75038-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For serdev framework, tty->dev is a NULL pointer, lpuart_uport_is_active
calling device_may_wakeup() may cause kernel NULL pointer crash, so here
add the NULL pointer check before using it.
Fixes: 4f5cb8c5e9 ("tty: serial: fsl_lpuart: enable wakeup source for lpuart")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230323110923.24581-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to LPUART RM, Transmission Complete Flag becomes 0 if queuing
a break character by writing 1 to CTRL[SBK], so here need to avoid
checking for transmission complete when UARTCTRL_SBK is asserted,
otherwise the lpuart32_tx_empty may never get TIOCSER_TEMT.
Commit 2411fd94ceaa("tty: serial: fsl_lpuart: skip waiting for
transmission complete when UARTCTRL_SBK is asserted") only fix it in
lpuart32_set_termios(), here also fix it in lpuart32_tx_empty().
Fixes: 380c966c09 ("tty: serial: fsl_lpuart: add 32-bit register interface support")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230323054415.20363-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede reported Bluetooth adapters (HCIs) connected over an UART
connection failed due corrupted Rx payload. The problem was narrowed
down to DMA Rx starting on UART_IIR_THRI interrupt. The problem occurs
despite LSR having DR bit set, which is precondition for attempting to
start DMA Rx in the first place.
From a debug patch:
[x.807834] 8250irq: iir=cc lsr+saved=60 received=0/15 ier=0f dma_t/rx/err=0/0/0
[x.808676] 8250irq: iir=c2 lsr+saved=61 received=0/0 ier=0f dma_t/rx/err=0/0/0
[x.808776] 8250irq: iir=cc lsr+saved=60 received=1/12 ier=0d dma_t/rx/err=0/1/0
[x.808870] Bluetooth: hci0: Frame reassembly failed (-84)
In the debug snippet, received field indicates 1 byte was transferred
over DMA and 12 bytes after that with the non-DMA Rx. The sole byte DMA
handled was corrupted (gets zeroed) which leads to the HCI failure.
This problem became apparent after commit e8ffbb71f7 ("serial: 8250:
use THRE & __stop_tx also with DMA") changed Tx stop behavior. Tx stop
is now triggered from a THRI interrupt.
Despite that this problem looks like a HW bug, this fix is not adding
UART_BUG_xx flag to the driver beucase it seems useful in general to
avoid starting DMA when there are only a few bytes to transfer.
Skipping DMA for small transfers avoids the extra overhead DMA incurs.
Thus, don't setup DMA Rx on UART_IIR_THRI but leave it to a subsequent
interrupt which has Rx a related IIR value.
By returning false from handle_rx_dma(), the DMA vs non-DMA decision is
postponed until either UART_IIR_RDI (FIFO threshold worth of bytes
awaiting) or UART_IIR_TIMEOUT (inter-character timeout) triggers at a
later time which allows better to discern whether the number of bytes
warrants starting DMA or not.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Fixes: e8ffbb71f7 ("serial: 8250: use THRE & __stop_tx also with DMA")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230317103034.12881-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fourth interrupt on SCI port is transmit end interrupt compared to
the break interrupt on other port types. So, shuffle the interrupts to fix
the transmit end interrupt handler.
Fixes: e1d0be6161 ("sh-sci: Add h8300 SCI")
Cc: stable <stable@kernel.org>
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230317150403.154094-1-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a potential race before THRE/TEMT deasserts when DMA Tx is
starting up (or the next batch of continuous Tx is being submitted).
This can lead to misdetecting Tx empty condition.
It is entirely normal for THRE/TEMT to be set for some time after the
DMA Tx had been setup in serial8250_tx_dma(). As Tx side is definitely
not empty at that point, it seems incorrect for serial8250_tx_empty()
claim Tx is empty.
Fix the race by also checking in serial8250_tx_empty() whether there's
DMA Tx active.
Note: This fix only addresses in-kernel race mainly to make using
TCSADRAIN/FLUSH robust. Userspace can still cause other races but they
seem userspace concurrency control problems.
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230317113318.31327-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If userspace races tcsetattr() with a write, the drained condition
might not be guaranteed by the kernel. There is a race window after
checking Tx is empty before tty_set_termios() takes termios_rwsem for
write. During that race window, more characters can be queued by a
racing writer.
Any ongoing transmission might produce garbage during HW's
->set_termios() call. The intent of TCSADRAIN/FLUSH seems to be
preventing such a character corruption. If those flags are set, take
tty's write lock to stop any writer before performing the lower layer
Tx empty check and wait for the pending characters to be sent (if any).
The initial wait for all-writers-done must be placed outside of tty's
write lock to avoid deadlock which makes it impossible to use
tty_wait_until_sent(). The write lock is retried if a racing write is
detected.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230317113318.31327-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit b984d7b56d ("MIPS: sibyte: Remove unused config option
SIBYTE_BCM1x55"), an #if in the Broadcom SiByte DUART driver can be
simplified.
Simplify the prepreprocessor condition after config SIBYTE_BCM1x55 removal.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20230323071053.417-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty framework can support polling console to allow operation
in situations where interrupts are turned off. Adding polling mode
support allows using KGDB over serial console,
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/20230322223956.84647-1-arend.vanspriel@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The direction field in the DMA config is deprecated. The sh-sci driver
sets {src,dst}_{addr,addr_width} based on the DMA direction and
it results in dmaengine_slave_config() failure as RZ DMAC driver
validates {src,dst}_addr_width values independent of DMA direction.
Fix this issue by passing both {src,dst}_{addr,addr_width}
values independent of DMA direction.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230322074717.6057-1-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1ea35b3557 ("ARM: s3c: remove s3c24xx specific hacks"), allows
simplifying the whole config logic for SERIAL_SAMSUNG_UARTS, and did this
config simplification. However, it misses that SERIAL_SAMSUNG_UARTS_4's
effect was just to control SERIAL_SAMSUNG_UARTS, and with the commit's
change, the config SERIAL_SAMSUNG_UARTS_4 has no remaining effect and can
be deleted.
Remove this obsolete config SERIAL_SAMSUNG_UARTS_4.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230317071538.29366-1-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On sc7180 Chromebooks, I did the following:
* Didn't enable earlycon in the kernel command line.
* Didn't enable serial console in the kernel command line.
* Didn't enable an agetty or any other client of "/dev/ttyMSM0".
* Added "kgdboc=ttyMSM0" to the kernel command line.
After I did that, I tried to enter kdb with this command over an ssh
session:
echo g > /proc/sysrq-trigger
When I did that the system just hung.
Although I thought I'd tested this scenario before, I couldn't go back
and find a time when it was working. Previous testing must have relied
on either the UART acting as the kernel console or an agetty running.
It turns out to be pretty easy to fix: we can just use
qcom_geni_serial_port_setup() as the .poll_init() function. This,
together with the patch ("serial: uart_poll_init() should power on the
UART"), allows the debugger to work even if there are no other users
of the serial port.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316132027.RESEND.2.Ie678853bb101091afe78cc8c22344bf3ff3aed74@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Qualcomm devices which use the "geni" serial driver, kdb/kgdb won't
be very happy if you use it but the resources of the port haven't been
powered on. Today kdb/kgdb rely on someone else powering the port
on. This could be the normal kernel console or an agetty running.
Let's fix this to explicitly power things on when setting up a polling
driver.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316132027.RESEND.1.I106c39498d8094c6f5e7ada42c7db17aa5c64e48@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The application which initializes the n_gsm ldisc may like to set
individual default parameters for each DLCI or take over of the application
specific DLCI configuration completely. This is currently not possible.
It is either possible to set common default parameters for all DLCIs or let
the user application set its DLCI specific configuration parameters.
Add support of GSMIOC_GETCONF_DLCI and GSMIOC_SETCONF_DLCI for the n_gsm
ldisc handle to support DLCI specific parameter configuration upfront.
Add a code example for this use case to the n_gsm documentation.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230315105354.6234-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 6 describes the error recovery mode option
which is based on I frames. The k parameter defines the maximum number of
I frames that a DLC can have unacknowledged as described in chapter 5.7.4.
The current n_gsm implementation does not support the error recovery mode
option. However, the k parameter is also part of the parameter negotiation
message as described in chapter 5.4.6.3.1. Chapter 5.7.4 also notes that
the allowed value range for k is 1-7. That means a 0 is counted as invalid
here. This means that the user needs to configure a valid value here even
if the function itself is not supported. Otherwise, parameter negotiation
may fail.
Allow setting of k via ioctl in gsm_config(). Range checks are already
included.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230315105354.6234-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Parameter negotiation has been introduced with
commit 92f1f0c329 ("tty: n_gsm: add parameter negotiation support")
However, means to set individual parameters per DLCI are not yet
implemented. Furthermore, it is currently not possible to keep a DLCI half
open until the user application sets the right parameters for it. This is
required to allow a user application to set its specific parameters before
the underlying link is established. Otherwise, the link is opened and
re-established right afterwards if the user application sets incompatible
parameters. This may be an unexpected behavior for the peer.
Add parameter 'wait_config' to 'gsm_config' to support setups where the
DLCI specific user application sets its specific parameters after open()
and before the link gets fully established. Setting this to zero disables
the user application specific DLCI configuration option.
Add the ioctls 'GSMIOC_GETCONF_DLCI' and 'GSMIOC_SETCONF_DLCI' for the
ldisc and virtual ttys. This gets/sets the DLCI specific parameters and may
trigger a reconnect of the DLCI if incompatible values have been set. Only
the parameters for the DLCI associated with the virtual tty can be set or
retrieved if called on these.
Add remark within the documentation to introduce the new ioctls.
Link: https://lore.kernel.org/oe-kbuild-all/202302281856.S9Lz4gHB-lkp@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230315105354.6234-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCZB2KdAAKCRCAXGG7T9hj
vseqAP9OlHO4qqfTWlSmYSPisfWwDT6CM7+K+4vWpMXFh3ZGuAEAhER0mNM1ikoB
ZF7Ash778XPt2CaapQLsHtFZqJUn5gw=
=ouzt
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.3-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- fix build warning
- avoid concurrent accesses to the Xen PV console ring page
* tag 'for-linus-6.3-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/PVH: avoid 32-bit build warning when obtaining VGA console info
hvc/xen: prevent concurrent accesses to the shared ring
The hvc machinery registers both a console and a tty device based on
the hv ops provided by the specific implementation. Those two
interfaces however have different locks, and there's no single locks
that's shared between the tty and the console implementations, hence
the driver needs to protect itself against concurrent accesses.
Otherwise concurrent calls using the split interfaces are likely to
corrupt the ring indexes, leaving the console unusable.
Introduce a lock to xencons_info to serialize accesses to the shared
ring. This is only required when using the shared memory console,
concurrent accesses to the hypercall based console implementation are
not an issue.
Note the conditional logic in domU_read_console() is slightly modified
so the notify_daemon() call can be done outside of the locked region:
it's an hypercall and there's no need for it to be done with the lock
held.
Fixes: b536b4b962 ('xen: use the hvc console infrastructure for Xen console')
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20221130150919.13935-1-roger.pau@citrix.com
Signed-off-by: Juergen Gross <jgross@suse.com>
We need the tty/serial fixes in here and it resolves a merge conflict
with:
drivers/tty/serial/8250/8250_em.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the mainline fixes in this branch for testing and other
subsystem changes to be based properly on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small tty and serial driver fixes for 6.3-rc3 to resolve
some reported issues.
They include:
- 8250 driver Kconfig issue pointed out by you that showed up in -rc1
- qcom-geni serial driver fixes
- various 8250 driver fixes for reported problems
- fsl_lpuart driver fixes
- serdev fix for regression in -rc1
- vt.c bugfix
All have been in linux-next for over a week with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZBcinQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynIYACgjP49Xy1N6hDLZJgKxvnPLmvnhY4AoKM8CkHI
zbWudA1fBqsYLFtxNKaQ
=/Ond
-----END PGP SIGNATURE-----
Merge tag 'tty-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty and serial driver fixes for 6.3-rc3 to resolve
some reported issues.
They include:
- 8250 driver Kconfig issue pointed out by you that showed up in -rc1
- qcom-geni serial driver fixes
- various 8250 driver fixes for reported problems
- fsl_lpuart driver fixes
- serdev fix for regression in -rc1
- vt.c bugfix
All have been in linux-next for over a week with no reported problems"
* tag 'tty-6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: vt: protect KD_FONT_OP_GET_TALL from unbound access
serial: qcom-geni: drop bogus uart_write_wakeup()
serial: qcom-geni: fix mapping of empty DMA buffer
serial: qcom-geni: fix DMA mapping leak on shutdown
serial: qcom-geni: fix console shutdown hang
serdev: Set fwnode for serdev devices
tty: serial: fsl_lpuart: fix race on RX DMA shutdown
serial: 8250_pci1xxxx: Disable SERIAL_8250_PCI1XXXX config by default
serial: 8250_fsl: fix handle_irq locking
serial: 8250_em: Fix UART port type
serial: 8250: ASPEED_VUART: select REGMAP instead of depending on it
tty: serial: fsl_lpuart: skip waiting for transmission complete when UARTCTRL_SBK is asserted
Revert "tty: serial: fsl_lpuart: adjust SERIAL_FSL_LPUART_CONSOLE config dependency"
The module pointer in class_create() never actually did anything, and it
shouldn't have been requred to be set as a parameter even if it did
something. So just remove it and fix up all callers of the function in
the kernel tree at the same time.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20230313181843.1207845-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The arbitration of the UART DMA is mishandled for a few
exceptional cases when probing and releasing the driver.
It is possible that the DMA register spaces are not defined in
device tree for an instance of the driver, so attempts to access
the registers in brcmuart_arbitration() would use NULL pointers.
It is also possible for the probe function to return an error
while still holding the UART DMA. This would prevent the UART
DMA from being claimed by an instance that could use it.
These errors are addressed by only releasing the UART DMA if it
is held by this instance (i.e. priv->dma_enabled == 1) and
directing early error paths in probe to this common release_dma
handling.
Fixes: 41a469482d ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230309190224.687380-1-opendmb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hw_stopped in tty_struct is used like bool, convert the variable type
to bool.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Link: https://lore.kernel.org/r/20230309082035.14880-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When PARMRK is set, a character can result in up to 3 chars in the read
buffer. Receive code calculates for how many characters there (at
least) is room. Convert an opencoded rounding in the calculation to use
DIV_ROUND_UP().
Note: the room variable is decremented afterwards by one which ensures
the characters will fit into the buffer for real so the code is okay
despite rounding upwards.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230309082035.14880-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The no_space_left variable is only assigned with 0 and 1.
Change its type to boolean and move negation from its name into the
check.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230309082035.14880-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hw_stopped in uart_change_line_settings() stores old hw_stopped, thus
rename it appropriately.
Alter logic to check first if the hw_stopped was changed, and then pick
which function to call if it was because the logic is more obvious that
way.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230309080923.11778-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert hw_stopped in uart_port to bool because its more appropriate
type for how it is used.
Also convert the local variable in uart_change_line_settings() caching
old hw_stopped to bool.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230309080923.11778-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_change_speed() changes more than just speed so rename it to more
generic uart_change_line_settings().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230309080923.11778-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Compare against B0 rather than assume B0 equals zero, which is true for
all archs but explicit B0 makes the code more obvious.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230309080923.11778-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here).
drivers/tty/serial/sprd_serial.c:1242:34: error: ‘serial_ids’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230310222957.315848-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/tty/serial/sh-sci.c:3144:34: error: ‘of_sci_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230310222957.315848-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230310144727.1545699-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230310144727.1545630-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/lkml/20221118224540.619276-572-uwe@kleine-koenig.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In ioctl(KD_FONT_OP_GET_TALL), userland tells through op->height which
vpitch should be used to copy over the font. In con_font_get, we were
not checking that it is within the maximum height value, and thus
userland could make the vc->vc_sw->con_font_get(vc, &font, vpitch);
call possibly overflow the allocated max_font_size bytes, and the
copy_to_user(op->data, font.data, c) call possibly read out of that
allocated buffer.
By checking vpitch against max_font_height, the max_font_size buffer
will always be large enough for the vc->vc_sw->con_font_get(vc, &font,
vpitch) call (since we already prevent loading a font larger than that),
and c = (font.width+7)/8 * vpitch * font.charcount will always remain
below max_font_size.
Fixes: 24d69384bc ("VT: Add KD_FONT_OP_SET/GET_TALL operations")
Reported-by: syzbot+3af17071816b61e807ed@syzkaller.appspotmail.com
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230306094921.tik5ewne4ft6mfpo@begin
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ipwireless' Kconfig entry is currently sitting in char/pcmcia. But
the driver is in tty/. So move the entry to tty/ too.
First, it makes sense to have the entry along the driver. Second, whole
char/pcmcia is about to pass away.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: David Sterba <dsterba@suse.com>
Link: https://lore.kernel.org/r/20230222092302.6348-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the bogus uart_write_wakeup() from when setting up a new DMA
transfer, which does not free up any more space in the ring buffer.
Any pending writers will be woken up when the transfer completes.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Link: https://lore.kernel.org/r/20230307164405.14218-5-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that there is data in the ring buffer before trying to set up
a zero-length DMA transfer.
This specifically fixes the following warning when unmapping the empty
buffer on the sc8280xp-crd:
WARNING: CPU: 0 PID: 138 at drivers/iommu/dma-iommu.c:1046 iommu_dma_unmap_page+0xbc/0xd8
...
Call trace:
iommu_dma_unmap_page+0xbc/0xd8
dma_unmap_page_attrs+0x30/0x1c8
geni_se_tx_dma_unprep+0x28/0x38
qcom_geni_serial_isr+0x358/0x75c
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Cc: stable <stable@kernel.org>
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Link: https://lore.kernel.org/r/20230307164405.14218-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix what appears to be a copy-paste error that can lead to a leaked DMA
mapping on close() and failure to restart TX after the port is reopened.
Note that rx_dma_addr is generally NULL when
qcom_geni_serial_stop_tx_dma() is called as part of shutdown() (but
tx_dma_addr need not be).
Fixes: 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Cc: stable <stable@kernel.org>
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Link: https://lore.kernel.org/r/20230307164405.14218-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent commit added back the calls top stop tx and rx to shutdown()
which had previously been removed by commit e83766334f ("tty: serial:
qcom_geni_serial: No need to stop tx/rx on UART shutdown") in order to
be able to use kgdb after stopping the getty.
Not only did this again break kgdb, but it also broke serial consoles
more generally by hanging TX when stopping the getty during reboot.
The underlying problem has been there since the driver was first merged
and fixing it is going to be a bit involved so simply stop calling the
broken stop functions during shutdown for consoles for now.
Fixes: d8aca2f968 ("tty: serial: qcom-geni-serial: stop operations in progress at shutdown")
Cc: stable <stable@kernel.org>
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Link: https://lore.kernel.org/r/20230307164405.14218-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per RZ/V2M hardware manual(Rev.1.30 Jun, 2022), UART IP has a
restriction as mentioned below.
40.6.1 Point for Caution when Changing the Register Settings:
When changing the settings of the following registers, a PRESETn master
reset or FIFO reset + SW reset (FCR[2],FCR[1], HCR0[7]) must be input to
re-initialize them.
Target Registers: FCR, LCR, MCR, DLL, DLM, HCR0.
Add serial8250_em_reg_update() and serial8250_em_serial_out_helper() to
handle this restriction. serial8250_em_serial_out_helper() is identical to
previous serial8250_em_serial_out() except that UART_FCR macro is removed
from serial8250_em_serial_out_helper() as it is now handled by serial8250_
em_serial_out().
DLL/DLM register can be updated only by setting LCR[7]. So the
updation of LCR[7] will perform reset for DLL/DLM register changes.
EMMA mobile has the same register set as RZ/V2M and this patch is tested on
EMEV2 board. So, there is no harm in applying the same restriction here as
well as the HW manual for EMMA mobile is not updated for a long time.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-8-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART_FCR shares the same offset with UART_IIR. We cannot use UART_FCR
in serial8250_em_serial_in() as it overlaps with UART_IIR.
Define UART_FCR_EM macro with a high value to avoid overlapping
with existing UART_* register defines and define another macro
UART_FCR_EM_HW for the real offset.
Use these macros in serial8250_em_serial{_in/_out} function to
read/write FCR register.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-7-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify clk handling in probe() by replacing devm_clk_get()->devm_
clk_get_enabled(). This replaces the usage of clk_prepare_enable/clk_
disable_unprepare() in probe()/remove(). After that sclk is no
longer required in struct serial8250_em_priv and is replaced by a
local variable sclk in probe().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-6-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify probe() by using dev_err_probe() instead of dev_err() and
add a local variable 'dev' to replace '&pdev->dev'.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per HW manual for EMEV2 "R19UH0040EJ0400 Rev.4.00", the UART
IP found on EMMA mobile SoC is Register-compatible with the
general-purpose 16750 UART chip. Fix UART port type as 16750 and
enable 64-bytes fifo support.
Fixes: 22886ee968 ("serial8250-em: Emma Mobile UART driver V2")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-2-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amlogic Meson G12A (and later) SoCs also have the "divide XTAL by 2" bit
as the S4 UART controllers. Add a new compatible string for these SoCs
and enable the has_xtal_div2 flag for them.
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230307222651.2106615-3-martin.blumenstingl@googlemail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stm32_usart_transmit_chars() may be called with empty or stopped
transmit queue, and no XON/OFF character pending. This can happen at
the end of transmission, where this last call is used to either handle
the XON/XOFF x_char, or disable TX interrupt if queue is empty or
stopped.
If that occurs, do not assert the RS485 RTS/DE GPIO anymore, as the
GPIO would remain asserted past the end of transmission and that would
block the RS485 bus after the transmission.
Only assert the RS485 RTS/DE GPIO if there is either pending XON/XOFF
x_char, or at least one character in running transmit queue.
Fixes: d7c7671616 ("serial: stm32: Use TC interrupt to deassert GPIO RTS in RS485 mode")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230223042252.95480-2-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
register_sysctl_table() is a deprecated compatibility wrapper.
register_sysctl_init() can do the directory creation for you so just use
that
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20230302204612.782387-7-mcgrof@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no point in casting a struct uart_port to a struct imx_port
just to access the first member of the latter (a struct uart_port).
This introduces no code changes.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230302115417.1860210-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The int variable ret does not receive the return value in this function.
It should be removed and returned 0 directly.
Signed-off-by: Li zeming <zeming@nfschina.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230222202303.3195-1-zeming@nfschina.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From time to time DMA completion can come in the middle of DMA shutdown:
<process ctx>: <IRQ>:
lpuart32_shutdown()
lpuart_dma_shutdown()
del_timer_sync()
lpuart_dma_rx_complete()
lpuart_copy_rx_to_tty()
mod_timer()
lpuart_dma_rx_free()
When the timer fires a bit later, sport->dma_rx_desc is NULL:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
pc : lpuart_copy_rx_to_tty+0xcc/0x5bc
lr : lpuart_timer_func+0x1c/0x2c
Call trace:
lpuart_copy_rx_to_tty
lpuart_timer_func
call_timer_fn
__run_timers.part.0
run_timer_softirq
__do_softirq
__irq_exit_rcu
irq_exit
handle_domain_irq
gic_handle_irq
call_on_irq_stack
do_interrupt_handler
...
To fix this fold del_timer_sync() into lpuart_dma_rx_free() after
dmaengine_terminate_sync() to make sure timer will not be re-started in
lpuart_copy_rx_to_tty() <= lpuart_dma_rx_complete().
Fixes: 4a8588a1cf ("serial: fsl_lpuart: delete timer on shutdown")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20230309134302.74940-2-alexander.sverdlin@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 handle_irq callback is not just called from the interrupt
handler but also from a timer callback when polling (e.g. for ports
without an interrupt line). Consequently the callback must explicitly
disable interrupts to avoid a potential deadlock with another interrupt
in polled mode.
Fix up the two paths in the freescale callback that failed to re-enable
interrupts when polling.
Fixes: 853a9ae29e ("serial: 8250: fix handle_irq locking")
Cc: stable@vger.kernel.org # 5.13
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/Y/xYzqp4ogmOF5t0@kili
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230227085046.24282-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per HW manual for EMEV2 "R19UH0040EJ0400 Rev.4.00", the UART
IP found on EMMA mobile SoC is Register-compatible with the
general-purpose 16750 UART chip. Fix UART port type as 16750 and
enable 64-bytes fifo support.
Fixes: 22886ee968 ("serial8250-em: Emma Mobile UART driver V2")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-2-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: 8d310c9107 ("drivers/tty/serial/8250: Make Aspeed VUART SIRQ polarity configurable")
Cc: stable <stable@kernel.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Oskar Senft <osk@google.com>
Cc: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/20230226053953.4681-9-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to LPUART RM, Transmission Complete Flag becomes 0 if queuing
a break character by writing 1 to CTRL[SBK], so here need to skip
waiting for transmission complete when UARTCTRL_SBK is asserted,
otherwise the kernel may stuck here.
And actually set_termios() adds transmission completion waiting to avoid
data loss or data breakage when changing the baud rate, but we don't
need to worry about this when queuing break characters.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230223093941.31790-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 5779a072c2.
This results in a link error of
ld: drivers/tty/serial/earlycon.o: in function `parse_options':
drivers/tty/serial/earlycon.c:99: undefined reference to `uart_parse_earlycon'
When the config is in this state
CONFIG_SERIAL_CORE=m
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_SERIAL_EARLYCON=y
CONFIG_SERIAL_FSL_LPUART=m
CONFIG_SERIAL_FSL_LPUART_CONSOLE=y
Fixes: 5779a072c2 ("tty: serial: fsl_lpuart: adjust SERIAL_FSL_LPUART_CONSOLE config dependency")
Cc: stable <stable@kernel.org>
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230226173846.236691-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 226fae124b ("vc_screen: move load of struct vc_data pointer in
vcs_read() to avoid UAF") moved the call to vcs_vc() into the loop.
While doing this it also moved the unconditional assignment of
ret = -ENXIO;
This unconditional assignment was valid outside the loop but within it
it clobbers the actual value of ret.
To avoid this only assign "ret = -ENXIO" when actually needed.
[ Also, the 'goto unlock_out" needs to be just a "break", so that it
does the right thing when it exits on later iterations when partial
success has happened - Linus ]
Reported-by: Storm Dragon <stormdragon2976@gmail.com>
Link: https://lore.kernel.org/lkml/Y%2FKS6vdql2pIsCiI@hotmail.com/
Fixes: 226fae124b ("vc_screen: move load of struct vc_data pointer in vcs_read() to avoid UAF")
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/lkml/64981d94-d00c-4b31-9063-43ad0a384bde@t-8ch.de/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Restore the vcs_size() handling in vcs_read() to what
it had been in previous version.
Fixes: 226fae124b ("vc_screen: move load of struct vc_data pointer in vcs_read() to avoid UAF")
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work falls
into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be moved
into read-only memory (i.e. const) The recent work with Rust has
pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only making
things safer overall. This is the contuation of that work (started
last release with kobject changes) in moving struct bus_type to be
constant. We didn't quite make it for this release, but the
remaining patches will be finished up for the release after this
one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/ipdg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynL3gCgwzbcWu0So3piZyLiJKxsVo9C2EsAn3sZ9gN6
6oeFOjD3JDju3cQsfGgd
=Su6W
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work
falls into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be
moved into read-only memory (i.e. const) The recent work with Rust
has pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only
making things safer overall. This is the contuation of that work
(started last release with kobject changes) in moving struct
bus_type to be constant. We didn't quite make it for this release,
but the remaining patches will be finished up for the release after
this one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems"
[ Geert Uytterhoeven points out that that last sentence isn't true, and
that there's a pending report that has a fix that is queued up - Linus ]
* tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (124 commits)
debugfs: drop inline constant formatting for ERR_PTR(-ERROR)
OPP: fix error checking in opp_migrate_dentry()
debugfs: update comment of debugfs_rename()
i3c: fix device.h kernel-doc warnings
dma-mapping: no need to pass a bus_type into get_arch_dma_ops()
driver core: class: move EXPORT_SYMBOL_GPL() lines to the correct place
Revert "driver core: add error handling for devtmpfs_create_node()"
Revert "devtmpfs: add debug info to handle()"
Revert "devtmpfs: remove return value of devtmpfs_delete_node()"
driver core: cpu: don't hand-override the uevent bus_type callback.
devtmpfs: remove return value of devtmpfs_delete_node()
devtmpfs: add debug info to handle()
driver core: add error handling for devtmpfs_create_node()
driver core: bus: update my copyright notice
driver core: bus: add bus_get_dev_root() function
driver core: bus: constify bus_unregister()
driver core: bus: constify some internal functions
driver core: bus: constify bus_get_kset()
driver core: bus: constify bus_register/unregister_notifier()
driver core: remove private pointer from struct bus_type
...
Here is the big set of serial and tty driver updates for 6.3-rc1.
Once again, Jiri and Ilpo have done a number of core vt and tty/serial
layer cleanups that were much needed and appreciated. Other than that,
it's just a bunch of little tty/serial driver updates:
- qcom-geni-serial driver updates
- liteuart driver updates
- hvcs driver cleanups
- n_gsm updates and additions for new features
- more 8250 device support added
- fpga/dfl update and additions
- imx serial driver updates
- fsl_lpuart updates
- other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/itAw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykJbQCfWv/J4ZElO108iHBU5mJCDagUDBgAnAtLLN6A
SEAnnokGCDtA/BNIXeES
=luRi
-----END PGP SIGNATURE-----
Merge tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of serial and tty driver updates for 6.3-rc1.
Once again, Jiri and Ilpo have done a number of core vt and tty/serial
layer cleanups that were much needed and appreciated. Other than that,
it's just a bunch of little tty/serial driver updates:
- qcom-geni-serial driver updates
- liteuart driver updates
- hvcs driver cleanups
- n_gsm updates and additions for new features
- more 8250 device support added
- fpga/dfl update and additions
- imx serial driver updates
- fsl_lpuart updates
- other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (143 commits)
tty: n_gsm: add keep alive support
serial: imx: remove a redundant check
dt-bindings: serial: snps-dw-apb-uart: add dma & dma-names properties
soc: qcom: geni-se: Move qcom-geni-se.h to linux/soc/qcom/geni-se.h
tty: n_gsm: add TIOCMIWAIT support
tty: n_gsm: add RING/CD control support
tty: n_gsm: mark unusable ioctl structure fields accordingly
serial: imx: get rid of registers shadowing
serial: imx: refine local variables in rxint()
serial: imx: stop using USR2 in FIFO reading loop
serial: imx: remove redundant USR2 read from FIFO reading loop
serial: imx: do not break from FIFO reading loop prematurely
serial: imx: do not sysrq broken chars
serial: imx: work-around for hardware RX flood
serial: imx: factor-out common code to imx_uart_soft_reset()
serial: 8250_pci1xxxx: Add power management functions to quad-uart driver
serial: 8250_pci1xxxx: Add RS485 support to quad-uart driver
serial: 8250_pci1xxxx: Add driver for quad-uart support
serial: 8250_pci: Add serial8250_pci_setup_port definition in 8250_pcilib.c
tty: pcn_uart: fix memory leak with using debugfs_lookup()
...
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate subsystem
trees, but the majority is in the same branch, in order to better handle
dependencies between the patches and avoid breaking bisection.
Unfortunately that leads to merge conflicts against other changes in the
subsystem trees, but they should all be trivial to resolve by removing
the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed. The
only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users.
-----BEGIN PGP SIGNATURE-----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=WejQ
-----END PGP SIGNATURE-----
Merge tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC boardfile updates from Arnd Bergmann
"Unused boardfile removal for 6.3
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate
subsystem trees, but the majority is in the same branch, in order to
better handle dependencies between the patches and avoid breaking
bisection.
Unfortunately that leads to merge conflicts against other changes in
the subsystem trees, but they should all be trivial to resolve by
removing the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed.
The only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users"
* tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (91 commits)
mmc: omap: drop TPS65010 dependency
ARM: pxa: restore mfp-pxa320.h
usb: ohci-omap: avoid unused-variable warning
ARM: debug: remove references in DEBUG_UART_8250_SHIFT to removed configs
ARM: s3c: remove obsolete s3c-cpu-freq header
MAINTAINERS: adjust SAMSUNG SOC CLOCK DRIVERS after s3c24xx support removal
MAINTAINERS: update file entries after arm multi-platform rework and mach-pxa removal
ARM: remove CONFIG_UNUSED_BOARD_FILES
mfd: remove htc-pasic3 driver
w1: remove ds1wm driver
usb: remove ohci-tmio driver
fbdev: remove w100fb driver
fbdev: remove tmiofb driver
mmc: remove tmio_mmc driver
mfd: remove ucb1400 support
mfd: remove toshiba tmio drivers
rtc: remove v3020 driver
power: remove pda_power supply driver
ASoC: pxa: remove unused board support
pcmcia: remove unused pxa/sa1100 drivers
...
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapters 5.4.6.3.4 and 5.1.8.1.3 describe the test
command which can be used to test the mux connection between both sides.
Currently, no algorithm is implemented to make use of this command. This
requires that each multiplexed upper layer protocol supervises the
underlying muxer connection to handle possible connection losses.
Introduce ioctl commands and functions to optionally enable keep alive
handling via the test command as described in chapter 5.4.6.3.4. A single
incrementing octet "ka_num" is being used for unique identification of each
single keep alive packet. Retries will use the same "ka_num" value as the
original packet. Retry count and interval are taken from the general
parameters N2 and T2.
Add usage description and basic example for the new ioctl to the n_gsm
documentation.
Note that support for the test command is mandatory and already present in
the muxer implementation since the very first version.
Also note that the previous ioctl structure gsm_config cannot be extended
due to missing checks against zero of the field "unused".
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230214122737.1976-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cpp_check reports
drivers/tty/serial/imx.c:1207:15: style: Condition 'r_bytes>0' is always true [knownConditionTrueFalse]
if (r_bytes > 0) {
r_byte is set to
r_bytes = rx_ring->head - rx_ring->tail;
The head - tail calculation is also done by the earlier check
if (rx_ring->head <= sg_dma_len(sgl) &&
rx_ring->head > rx_ring->tail) {
so r_bytes will always be > 0, so the second check is not needed.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Link: https://lore.kernel.org/r/20230211154550.2130670-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move include/linux/qcom-geni-se.h to include/linux/soc/qcom/geni-se.h.
This removes 1 of a few remaining Qualcomm-specific headers into a more
approciate subdirectory under include/.
Signed-off-by: Elliot Berman <quic_eberman@quicinc.com>
Acked-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Reviewed-by: Guru Das Srinagesh <quic_gurus@quicinc.com>
Link: https://lore.kernel.org/r/20230203210133.3552796-1-quic_eberman@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the TIOCMIWAIT ioctl on the virtual ttys. This enables the
user to wait for virtual modem signals like RING.
More work is needed to support also TIOCGICOUNT.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230206114606.2133-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The status lines ring and carrier detect are used by the modem to signal
incoming calls (RING) or an established connection (CD). This is
implemented as physical lines on a standard RS232 connection. However,
the muxer protocol encodes these status lines as modem bits IC and DV.
These incoming lines are masked by tty driver (see tty_io.c) and cannot be
set by a user application.
Allow setting RING via TIOCM_OUT1 and CD via TIOCM_OUT2 to allow
implementation of a modem or modem emulator.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230206114606.2133-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Neither registers shadowing is functionally needed as all the registers are
read-write, nor the shadowing makes much sense for speed-up, as most speed
critical reads/writes (of data Rx/Tx registers) are not shadowed anyway.
Moreover, the shadowing code is obviously pure overhead on the write path.
Get rid of the shadowing code and variables due to above considerations.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201141603.4205-1-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'rx' is chip register, similar to 'usr2', so let it be of 'u32' type as
well.
Move 'flg' to be FIFO read loop local as it's not used outside.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-8-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chip provides all the needed bits in the URXD0 register that we read
anyway for data, so get rid of reading USR2 and use only URXD0 bits
instead.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-7-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to read USR2 twice at every loop iteration: get rid of the
second read.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-6-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reason to prematurely break out of FIFO reading loop, and it
might cause needless reenters into ISR, so keep reading until FIFO is
empty.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-5-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not call uart_handle_sysrq_char() if we got any receive error along with
the character, as we don't want random junk to be considered a sysrq.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-4-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check if hardware Rx flood is in progress, and issue soft reset to UART to
stop the flood.
A way to reproduce the flood (checked on iMX6SX) is: open iMX UART at 9600
8N1, and from external source send 0xf0 char at 115200 8N1. In about 90% of
cases this starts a flood of "receiving" of 0xff characters by the iMX UART
that is terminated by any activity on RxD line, or could be stopped by
issuing soft reset to the UART (just stop/start of RX does not help). Note
that in essence what we did here is sending isolated start bit about 2.4
times shorter than it is to be if issued on the UART configured baud rate.
There was earlier attempt to fix similar issue in: 'commit
b38cb7d257 ("serial: imx: Disable new features of autobaud detection")',
but apparently it only gets harder to reproduce the issue after that
commit.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-3-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We perform soft reset in 2 places, slightly differently for no sufficient
reasons, so move more generic variant to a function, and re-use the code.
Out of 2 repeat counters, 10 and 100, select 10, as the code works at
interrupts disabled, and in practice the reset happens immediately.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/20230201142700.4346-2-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci1xxxx's quad-uart function has the capability to wake up UART
from suspend state. Enable wakeup before entering into suspend and
disable wakeup on resume.
Co-developed-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Link: https://lore.kernel.org/r/20230207164814.3104605-5-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci1xxxx uart supports RS485 mode of operation in the hardware with
auto-direction control with configurable delay for releasing RTS after
the transmission. This patch adds support for the RS485 mode.
Co-developed-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230207164814.3104605-4-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci1xxxx is a PCIe switch with a multi-function endpoint on one of
its downstream ports. Quad-uart is one of the functions in the
multi-function endpoint. This driver loads for the quad-uart and
enumerates single or multiple instances of uart based on the PCIe
subsystem device ID.
Co-developed-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230207164814.3104605-3-kumaravel.thiagarajan@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.
Cc: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230202141221.2293012-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Synchronizes hotplug remove with the freeing of the port.
This ensures we have freed all the memory associated with
this port and are not leaking memory.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20230203155802.404324-6-brking@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When hotplug removing an hvcs device, we need to ensure the
hangup processing is done prior to exiting the remove function,
so use tty_vhangup to do the hangup processing directly
rather than using tty_hangup which simply schedules the hangup
work for later execution.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20230203155802.404324-5-brking@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rather than manually creating attributes for the hvcs driver,
let the driver core do this for us. This also fixes some hotplug
remove issues and ensures that cleanup of these attributes
is done in the right order.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20230203155802.404324-3-brking@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the dev_groups functionality to manage the attribute groups
for hvcs devices. This simplifies the code and also eliminates
errors coming from kernfs when attempting to remove a console
device that is in use.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20230203155802.404324-2-brking@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There maybe pending USR interrupt before requesting irq, however
uart_add_one_port has not executed, so there will be kernel panic:
[ 0.795668] Unable to handle kernel NULL pointer dereference at virtual addre
ss 0000000000000080
[ 0.802701] Mem abort info:
[ 0.805367] ESR = 0x0000000096000004
[ 0.808950] EC = 0x25: DABT (current EL), IL = 32 bits
[ 0.814033] SET = 0, FnV = 0
[ 0.816950] EA = 0, S1PTW = 0
[ 0.819950] FSC = 0x04: level 0 translation fault
[ 0.824617] Data abort info:
[ 0.827367] ISV = 0, ISS = 0x00000004
[ 0.831033] CM = 0, WnR = 0
[ 0.833866] [0000000000000080] user address but active_mm is swapper
[ 0.839951] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
[ 0.845953] Modules linked in:
[ 0.848869] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.1.1+g56321e101aca #1
[ 0.855617] Hardware name: Freescale i.MX8MP EVK (DT)
[ 0.860452] pstate: 000000c5 (nzcv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 0.867117] pc : __imx_uart_rxint.constprop.0+0x11c/0x2c0
[ 0.872283] lr : imx_uart_int+0xf8/0x1ec
The issue only happends in the inmate linux when Jailhouse hypervisor
enabled. The test procedure is:
while true; do
jailhouse enable imx8mp.cell
jailhouse cell linux xxxx
sleep 10
jailhouse cell destroy 1
jailhouse disable
sleep 5
done
And during the upper test, press keys to the 2nd linux console.
When `jailhouse cell destroy 1`, the 2nd linux has no chance to put
the uart to a quiese state, so USR1/2 may has pending interrupts. Then
when `jailhosue cell linux xx` to start 2nd linux again, the issue
trigger.
In order to disable irqs before requesting them, both UCR1 and UCR2 irqs
should be disabled, so here fix that, disable the Ageing Timer interrupt
in UCR2 as UCR1 does.
Fixes: 8a61f0c70a ("serial: imx: Disable irqs before requesting them")
Suggested-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Link: https://lore.kernel.org/r/20230206013016.29352-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous 'commit 846651eca0 ("serial: fsl_lpuart: RS485 RTS
polariy is inverse")' only fixed the inverse issue on lpuart 8bit
platforms.
This is a follow-up patch to fix the RS485 polarity inverse
issue on lpuart 32bit platforms.
Fixes: 03895cf41d ("tty: serial: fsl_lpuart: Add support for RS-485")
Reported-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20230207162420.3647904-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The relevant history introducing serial_lsr_in() looks as follows:
$ git log --graph --oneline --boundary 9fafe733514b..df36f3e3fbb7 -- drivers/tty/serial/8250/8250_port.c
* df36f3e3fb Merge tag 'v5.19-rc3' into tty-next
|\
| * be03b0651f serial: 8250: Store to lsr_save_flags after lsr read
* | ...
* | bdb70c424d serial: 8250: Create serial_lsr_in()
* | ce338e4477 serial: 8250: Store to lsr_save_flags after lsr read
* | ...
|/
o 9fafe73351 tty: remove CMSPAR ifdefs
So the patch "serial: 8250: Store to lsr_save_flags after lsr read" was
introduced twice and in one branch it was followed up by commit
bdb70c424d ("serial: 8250: Create serial_lsr_in()") which moved
explicit lsr_saved_flags handling into a new function serial_lsr_in().
When the two branches were merged in commit df36f3e3fb, we got both,
serial_lsr_in() and the explicit lsr_saved_flags handling.
So drop the explicit lsr_saved_flags handling.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230202104501.264686-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hvcs driver only ever gets two references to the port. One
at initialization time, and one at install time. Remove the code
that was trying to do multiple port puts for each open, which
would result in more puts than gets.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20230201195743.303163-2-brking@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As DMA Rx can be completed from two places, it is possible that DMA Rx
completes before DMA completion callback had a chance to complete it.
Once the previous DMA Rx has been completed, a new one can be started
on the next UART interrupt. The following race is possible
(uart_unlock_and_check_sysrq_irqrestore() replaced with
spin_unlock_irqrestore() for simplicity/clarity):
CPU0 CPU1
dma_rx_complete()
serial8250_handle_irq()
spin_lock_irqsave(&port->lock)
handle_rx_dma()
serial8250_rx_dma_flush()
__dma_rx_complete()
dma->rx_running = 0
// Complete DMA Rx
spin_unlock_irqrestore(&port->lock)
serial8250_handle_irq()
spin_lock_irqsave(&port->lock)
handle_rx_dma()
serial8250_rx_dma()
dma->rx_running = 1
// Setup a new DMA Rx
spin_unlock_irqrestore(&port->lock)
spin_lock_irqsave(&port->lock)
// sees dma->rx_running = 1
__dma_rx_complete()
dma->rx_running = 0
// Incorrectly complete
// running DMA Rx
This race seems somewhat theoretical to occur for real but handle it
correctly regardless. Check what is the DMA status before complething
anything in __dma_rx_complete().
Reported-by: Gilles BULOZ <gilles.buloz@kontron.com>
Tested-by: Gilles BULOZ <gilles.buloz@kontron.com>
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230130114841.25749-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__dma_rx_complete() is called from two places:
- Through the DMA completion callback dma_rx_complete()
- From serial8250_rx_dma_flush() after IIR_RLSI or IIR_RX_TIMEOUT
The former does not hold port's lock during __dma_rx_complete() which
allows these two to race and potentially insert the same data twice.
Extend port's lock coverage in dma_rx_complete() to prevent the race
and check if the DMA Rx is still pending completion before calling
into __dma_rx_complete().
Reported-by: Gilles BULOZ <gilles.buloz@kontron.com>
Tested-by: Gilles BULOZ <gilles.buloz@kontron.com>
Fixes: 9ee4b83e51 ("serial: 8250: Add support for dmaengine")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230130114841.25749-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Requesting an interrupt with IRQF_ONESHOT will run the primary handler
in the hard-IRQ context even in the force-threaded mode. The
force-threaded mode is used by PREEMPT_RT in order to avoid acquiring
sleeping locks (spinlock_t) in hard-IRQ context. This combination
makes it impossible and leads to "sleeping while atomic" warnings.
Use one interrupt handler for both handlers (primary and secondary)
and drop the IRQF_ONESHOT flag which is not needed.
Fixes: e359b4411c ("serial: stm32: fix threaded interrupt handling")
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Valentin Caron <valentin.caron@foss.st.com> # V3
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230120160332.57930-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct liteuart_port keeps tracking of UART ID which is also
saved in the struct uart_port as line member. Drop the former one
and use the latter everywhere.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Gabriel Somlo <gsomlo@gmail.com>
Link: https://lore.kernel.org/r/20230123192604.81452-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the probe we need to call all devm_*() first followed by
non-devm_*() calls. This is due to reversed clean up that
may happen in a wrong order otherwise. The driver currently
allocates xarray before calling
devm_platform_get_and_ioremap_resource(). While it's not an
issue in this certain case, it's still better to be pedantic.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Gabriel Somlo <somlo@cmu.edu>
Link: https://lore.kernel.org/r/20230123191741.79751-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lpuart of imx8ulp is basically the same as imx7ulp, but it supports
some new features based on imx7ulp, such as it can assert the DMA
request on EOP(end-of-packet).
Here add lpuart support for imx8ulp, and rx_watermark is set to 3 as
imx8ulp RX FIFO depth is 8.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-7-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add RTS watermark support for LPUART. The RX RTS_B output negates when
the number of empty words in the receive FIFO is greater or equal to
RTSWATER. Here set the RTSWATER to half of the rxfifo_size.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-6-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the growth of rx watermark, it's useful to enable the Receiver Idle
Empty function, it can assert the RDRF(Receive Data Register Full Flag)
when the receiver is idle for a number of idle characters and the FIFO
is not empty. It will generate a DMA request or interrupt, which can
avoid receive data being trapped in the RX FIFO since the number of
words received is less than the watermark.
Here set the RXIDEN as 0x3 which enable the RDRF assertion due to
partially filled FIFO when receiver is idle for 4 characters.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-5-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RXWATER value must be greater than 0 according to the LPUART
reference manual. And when the number of datawords in the receive
FIFO is greater than RXWATER, an interrupt or a DMA request is
generated, so no need to set the different value for lpuart interrupt
case and dma case. Here delete the wrong RXWATER setting for dma case
directly.
Fixes: 42b68768e5 ("serial: fsl_lpuart: DMA support for 32-bit variant")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-4-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since imx8qxp RX FIFO depth is 64 datawords, it will be better to set
the rx watermark as 31, which means when the number of datawords in the
receive FIFO(>= 32) is greater than the watermark, an interrupt or a DMA
request is generated.
Also keep the console rx watermark as 1 to make sure it responsive.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add rx_watermark parameter for struct lpuart_port to make the receive
watermark configurable for different platforms.
No function changed.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130064449.9564-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lpuart32_setup_watermark_enable() will configure the UART FIFO and
watermark, also enable the receiver and transmitter, this should be done
after the rx/tx dma steup ready.
Also add lpuart32_hw_disable() to make sure the receiver/transmitter and
interrupts are disabled during the dma steup.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230130054107.9119-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uevent() callback in struct device_type should not be modifying the
device that is passed into it, so mark it as a const * and propagate the
function signature changes out into all relevant subsystems that use
this callback.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bard Liao <yung-chuan.liao@linux.intel.com>
Cc: Chaitanya Kulkarni <kch@nvidia.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jilin Yuan <yuanjilin@cdjrlc.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Gross <markgross@kernel.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Cc: Sean Young <sean@mess.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Won Chung <wonchung@google.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for Thunderbolt
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230111113018.459199-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Goto to the correct rollback label instead of directly returning.
Fixes: 5602cf99dc ("serial: liteuart: add IRQ support for the RX path")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Gabriel Somlo <gsomlo@gmail.com>
Link: https://lore.kernel.org/r/20230123173857.40695-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2aaa43c707 ("tty: serial: qcom-geni-serial: add support for
serial engine DMA") renamed rx_fifo member to rf_buf which caused a
build failure when b8caf69a69 ("tty: serial: qcom-geni-serial: fix
slab-out-of-bounds on RX FIFO buffer") from tty-linus was merged into
tty-next.
Fix the member variable name.
Fixes: 7a6aa989f2 ("Merge 6.2-rc5 into tty-next")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230123173857.40695-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small tty and serial driver fixes for 6.2-rc5 that resolve
a number of tiny reported issues and some new device ids. They include:
- new device id for the exar serial driver
- speakup tty driver bugfix
- atmel serial driver baudrate fixup
- stm32 serial driver bugfix and then revert as the bugfix broke the
build. That will come back in a later pull request once it is all
worked out properly.
- amba-pl011 serial driver rs486 mode bugfix
- qcom_geni serial driver bugfix
Most of these have been in linux-next with no reported problems (well,
other than the build breakage which generated the revert), the new
device id passed 0-day testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY8wDQA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynGegCguB+ZpDHKt9wccrGP3h/dwT2MAm8AnAqG4bmy
Yw/cHHPt9gx+AW6RBtAL
=EymN
-----END PGP SIGNATURE-----
Merge tag 'tty-6.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty and serial driver fixes for 6.2-rc5 that
resolve a number of tiny reported issues and some new device ids. They
include:
- new device id for the exar serial driver
- speakup tty driver bugfix
- atmel serial driver baudrate fixup
- stm32 serial driver bugfix and then revert as the bugfix broke the
build. That will come back in a later pull request once it is all
worked out properly.
- amba-pl011 serial driver rs486 mode bugfix
- qcom_geni serial driver bugfix
Most of these have been in linux-next with no reported problems (well,
other than the build breakage which generated the revert), the new
device id passed 0-day testing"
* tag 'tty-6.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: exar: Add support for Sealevel 7xxxC serial cards
Revert "serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler"
tty: serial: qcom_geni: avoid duplicate struct member init
serial: atmel: fix incorrect baudrate setup
tty: fix possible null-ptr-defer in spk_ttyio_release
serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler
serial: amba-pl011: fix high priority character transmission in rs486 mode
serial: pch_uart: Pass correct sg to dma_unmap_sg()
tty: serial: qcom-geni-serial: fix slab-out-of-bounds on RX FIFO buffer
Add support for Sealevel 7xxxC serial cards.
This patch:
* Adds IDs to recognize 7xxxC cards from Sealevel Systems.
* Updates exar_pci_probe() to set nr_ports to last two bytes of primary
dev ID for these cards.
Signed-off-by: Matthew Howell <matthew.howell@sealevel.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2301191440010.22558@tstest-VirtualBox
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit f24771b62a as it is
reported to break the build.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/202301200130.ttBiTzfO-lkp@intel.com
Fixes: f24771b62a ("serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler")
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Valentin Caron <valentin.caron@foss.st.com> # V3
Cc: Marek Vasut <marex@denx.de>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves 32x32 font size limitation checking down to drivers, so that
fbcon can allow large fonts.
We still keep a limitation to 64x128 pixels so as to have a simple bounded
allocation for con_font_get and in the userland kbd tool. That glyph size
will however be enough to have 128x36 characters on a "16/9 8K display".
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Link: https://lore.kernel.org/r/20230119151935.112415738@ens-lyon.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The KD_FONT_OP_SET/GET operations hardcode vpitch to be 32 pixels,
which only dates from the old VGA hardware which as asserting this.
Drivers such as fbcon however do not have such limitation, so this
introduces KD_FONT_OP_SET/GET_TALL operations, which userland can try
to use to avoid this limitation, thus opening the patch to >32 pixels
font height.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Link: https://lore.kernel.org/r/20230119151935.013597162@ens-lyon.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current con_font_get/set API currently hardcodes a 32-pixel-tall
limitation, which only dates from the old VGA hardware which could not
handle taller fonts than that.
This change just adds a vpitch parameter to release this
constraint. Drivers which do not support vpitch != 32 can just return
EINVAL when it is not 32, font loading tools will revert to trying 32
and succeed.
This change makes the fbcon driver consider vpitch appropriately, thus
making it able to load large fonts.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Link: https://lore.kernel.org/r/20230119151934.932642243@ens-lyon.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When -Woverride-init is enabled in a build, gcc points out that
qcom_geni_serial_pm_ops contains conflicting initializers:
drivers/tty/serial/qcom_geni_serial.c:1586:20: error: initialized field overwritten [-Werror=override-init]
1586 | .restore = qcom_geni_serial_sys_hib_resume,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/tty/serial/qcom_geni_serial.c:1586:20: note: (near initialization for 'qcom_geni_serial_pm_ops.restore')
drivers/tty/serial/qcom_geni_serial.c:1587:17: error: initialized field overwritten [-Werror=override-init]
1587 | .thaw = qcom_geni_serial_sys_hib_resume,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Open-code the initializers with the version that was already used,
and use the pm_sleep_ptr() method to deal with unused ones,
in place of the __maybe_unused annotation.
Fixes: 35781d8356 ("tty: serial: qcom-geni-serial: Add support for Hibernation feature")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20221215165453.1864836-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ba47f97a18 ("serial: core: remove baud_rates when serial console
setup") changed uart_set_options to select the correct baudrate
configuration based on the absolute error between requested baudrate and
available standard baudrate settings.
Prior to that commit the baudrate was selected based on which predefined
standard baudrate did not exceed the requested baudrate.
This change of selection logic was never reflected in the atmel serial
driver. Thus the comment left in the atmel serial driver is no longer
accurate.
Additionally the manual rounding up described in that comment and applied
via (quot - 1) requests an incorrect baudrate. Since uart_set_options uses
tty_termios_encode_baud_rate to determine the appropriate baudrate flags
this can cause baudrate selection to fail entirely because
tty_termios_encode_baud_rate will only select a baudrate if relative error
between requested and selected baudrate does not exceed +/-2%.
Fix that by requesting actual, exact baudrate used by the serial.
Fixes: ba47f97a18 ("serial: core: remove baud_rates when serial console setup")
Cc: stable <stable@kernel.org>
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20230109072940.202936-1-t.schramm@manjaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a Device Feature List (DFL) bus driver for the Altera
16550 implementation of UART.
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Marco Pagani <marpagan@redhat.com>
Link: https://lore.kernel.org/r/20230115151447.1353428-5-matthew.gerlach@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use active consistently for naming parameters and variables.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-13-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert various parameter names for ->dtr_rts() and related functions
from onoff, on, and raise to active.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-12-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert uart_handle_cts_change() to bool which is more appropriate
than unsigned int.
Rename status to active to better describe what the parameter means.
While at it, make the comment about the active parameter easier to
parse.
Cleanup callsites from operations that are not necessary with bool.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-10-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert status parameter for ->dcd_change() and
uart_handle_dcd_change() to bool which matches to how the parameter is
used.
Rename status to active to better describe what the parameter means.
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the raise/on parameter in ->dtr_rts() to bool through the
callchain. The parameter is used like bool. In USB serial, there
remains a few implicit bool -> larger type conversions because some
devices use u8 in their control messages.
In moxa_tiocmget(), dtr variable was reused for line status which
requires int so use a separate variable for status.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return boolean from ->carrier_raised() instead of 0 and 1. Make the
return type change also to tty_port_carrier_raised() that makes the
->carrier_raised() call (+ cd variable in moxa into which its return
value is stored).
Also cleans up a few unnecessary constructs related to this change:
return xx ? 1 : 0;
-> return xx;
if (xx)
return 1;
return 0;
-> return xx;
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert init_hw parameter in uart_startup() and uart_port_startup() to
bool as code treats them like bool.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return type of tty_port_initialized() is bool, use matching type for
the local variable.
Also reorder the local vars to reverse-xmas-tree while at it.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the devm_clk_get() may return ERR_PTR, its return value needs to be
checked to avoid invalid poineter dereference.
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221125093832.33386-1-yuancan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a RX_DURING_TX GPIO is defined by the DT property "rs485-rx-during-tx-gpios"
this patch switches this GPIO accordingly to the RS485 flag RX_DURING_TX in user
space. Controlled by this GPIO, now the hardware is responsible for connecting
or disconnecting RX during TX.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Link: https://lore.kernel.org/r/20221202104127.122761-4-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a RX_DURING_TX GPIO is defined by the DT property "rs485-rx-during-tx-gpios"
this patch switches this GPIO accordingly to the RS485 flag RX_DURING_TX in user
space. In addition, the i.MX UART receiver is no longer turned on and off during
sending, because now the hardware is responsible for connecting or disconnecting
RX during TX controlled by this GPIO.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Link: https://lore.kernel.org/r/20221202104127.122761-3-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch provides a generic GPIO variable for outputting the state
of RS485 RX_DURING_TX. The GPIO is defined by the devicetree property
"rs485-rx-during-tx-gpios". To use it in a low level serial driver,
the evaluation of this variable must be implemented there accordingly.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Link: https://lore.kernel.org/r/20221202104127.122761-2-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing clk_disable_unprepare() before return from
tegra_uart_hw_init() in the error handling path.
When request_irq() fails in tegra_uart_startup(), 'tup->uart_clk'
has been enabled, fix it by adding clk_disable_unprepare().
Fixes: cc9ca4d958 ("serial: tegra: Only print FIFO error message when an error occurs")
Fixes: d781ec21ba ("serial: tegra: report clk rate errors")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Link: https://lore.kernel.org/r/20221126020852.113378-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO controller component of the sc16is7xx driver is setup too
early, which can result in a race condition where another device tries
to utilise the GPIO lines before the sc16is7xx device has finished
initialising.
This issue manifests itself as an Oops when the GPIO lines are configured:
Unable to handle kernel read from unreadable memory at virtual address
...
pc : sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx]
lr : sc16is7xx_gpio_direction_output+0x4c/0x108 [sc16is7xx]
...
Call trace:
sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx]
gpiod_direction_output_raw_commit+0x64/0x318
gpiod_direction_output+0xb0/0x170
create_gpio_led+0xec/0x198
gpio_led_probe+0x16c/0x4f0
platform_drv_probe+0x5c/0xb0
really_probe+0xe8/0x448
driver_probe_device+0xe8/0x138
__device_attach_driver+0x94/0x118
bus_for_each_drv+0x8c/0xe0
__device_attach+0x100/0x1b8
device_initial_probe+0x28/0x38
bus_probe_device+0xa4/0xb0
deferred_probe_work_func+0x90/0xe0
process_one_work+0x1c4/0x480
worker_thread+0x54/0x430
kthread+0x138/0x150
ret_from_fork+0x10/0x1c
This patch moves the setup of the GPIO controller functions to later in the
probe function, ensuring the sc16is7xx device has already finished
initialising by the time other devices try to make use of the GPIO lines.
The error handling has also been reordered to reflect the new
initialisation order.
Co-developed-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: Isaac True <isaac.true@canonical.com>
Link: https://lore.kernel.org/r/20221130105529.698385-1-isaac.true@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ucc_uart_probe(), we have added proper of_node_put() in the failure
paths. However, we miss it before we free *qe_port* in the remove() function.
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20221205085437.1163682-1-windhl@126.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The qcom-geni-serial driver currently only works in SE FIFO mode. This
limits the UART speed to around 180 kB/s. In order to achieve higher
speeds we need to use SE DMA mode.
Keep the console port working in FIFO mode but extend the code to use DMA
for the high-speed port.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-15-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of checking the device compatible in probe(), assign the
device-specific data to struct of_device_id. We'll use it later when
providing SE DMA support.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-13-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return value of the handle_rx() callback is never checked. Drop it.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-12-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shuffle the code a bit, drop unneeded variables, make types of others
more consistent and use uart_xmit_advance() instead of handling
tail->xmit manually.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-11-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
qcom_geni_serial_handle_tx() is pretty big, let's move the code that
handles the actual writing of data to a separate function which makes
sense in preparation for introducing a dma variant of handle_tx().
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-10-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove stray newlines around #ifdefs for consistency with the rest
of the driver code.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-7-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The member we want to resolve in struct qcom_geni_serial_port is called
uport so we don't need an additional redundant parameter in this macro.
While at it: turn the macro into a static inline function.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-6-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop all unused symbols from the driver.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-4-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we shuffle the code a bit, we can drop all forward definitions of
various static functions.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-3-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't stop transmissions in progress at shutdown. This is fine with
FIFO SE mode but with DMA (support for which we'll introduce later) it
causes trouble so fix it now.
Fixes: e83766334f ("tty: serial: qcom_geni_serial: No need to stop tx/rx on UART shutdown")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-2-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's used on few places, so make the code easier to follow by caching
the subtraction result.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230112080136.4929-11-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The algorithm used for scrolling is the array juggling. It has
complexity O(N) and space complexity O(1). I.e. quite fast w/o
requirements for temporary storage.
Move the algorithm to a separate function so it is obvious what it is.
It is almost generic (except the array type), so if anyone else wants
array rotation, feel free to make it generic and move it to include/.
And rename all the variables from i, j, k, sz, d, and so on to something
saner.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230112080136.4929-9-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After previous patches, we can simply test vc->vc_uni_lines, so do so in
many unicode functions. This makes the code more compact. And even use
if (!)
return;
in vc_uniscr_scroll(), so that the whole code is indented on the left.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230112080136.4929-8-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to panic in vc_uniscr_copy_line(), just warn. This should never
happen though, as vc_uniscr_check() is supposed to be called before
vc_uniscr_copy_line(). And the former checks vc->vc_uni_lines already.
In any case, use _ONCE as vc_uniscr_copy_line() is called repeatedly for
each line. So don't flood the logs, just in case.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230112080136.4929-7-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It contains only lines with pointers to characters (u32s). So use
simple clear 'u32 **lines' all over the code.
This avoids zero-length arrays. It also makes the allocation less
error-prone (size of the struct wasn't taken into account at all).
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230112080136.4929-6-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It boils down to uint32_t, so use u32 directly, instead. This makes the
code more obvious.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230112080136.4929-5-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of sizeof(type), use sizeof(*variable) which is preferred. We
are going to remove the unicode's char32_t typedef, so this makes the
switch easier.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230112080136.4929-4-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NO_VC_UNI_SCREEN is defined nowhere. Remove the last reference to it.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230112080136.4929-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Its definition depends on the NO_VC_UNI_SCREEN macro. But that is never
defined, so remove all this completely. I.e. expand the macro to
vc->vc_uni_screen everywhere.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230112080136.4929-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VC_UNI_SCREEN_DEBUG is always defined as 0, so this code is never
executed. Drop it along with VC_UNI_SCREEN_DEBUG.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230112080136.4929-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comment in imx_uart_shutdown() says to disable the break condition,
but it doesn't actually do that, here fix this by disabling UCR1_SNDBRK
when closing the uart port like other uart drivers do.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221214031137.28815-4-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Need to disable the break condition for lpuart driver when closing
the uart port like other uart drivers do.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221214031137.28815-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LPUART IP has a bug that it treats the CTS as higher priority than the
break signal, which cause the break signal sending through UARTCTRL_SBK
may impacted by the CTS input if the HW flow control is enabled.
Add this workaround patch to fix the IP bug, we can disable CTS before
asserting SBK to avoid any interference from CTS, and re-enable it when
break off.
Such as for the bluetooth chip power save feature, host can let the BT
chip get into sleep state by sending a UART break signal, and wake it up
by turning off the UART break. If the BT chip enters the sleep mode
successfully, it will pull up the CTS line, if the BT chip is woken up,
it will pull down the CTS line. If without this workaround patch, the
UART TX pin cannot send the break signal successfully as it affected by
the BT CTS pin. After adding this patch, the BT power save feature can
work well.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221214031137.28815-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The LPUART Status Register needs to be cleared when closing the uart
port to get a clean environment when reopening the uart.
Fixes: 380c966c09 ("tty: serial: fsl_lpuart: add 32-bit register interface support")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221125101953.18753-4-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UARTBAUD_RDMAE and UARTBAUD_TDMAE are enabled in lpuart32_startup(), but
lpuart32_shutdown() not disable them, only free the dma ring buffer and
release the dma channels, so here disable the Rx/Tx DMA first in
lpuart32_shutdown().
Fixes: 42b68768e5 ("serial: fsl_lpuart: DMA support for 32-bit variant")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221125101953.18753-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the lpuart driver, the Idle Line Interrupt Enable now is only needed
for the CPU mode, so enable the UARTCTRL_ILIE at the correct place, and
clear it when shutdown.
Also need to configure the suitable UARTCTRL_IDLECFG, now the value is
0x7, represent 128 idle characters will trigger the Idle Line Interrupt.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221125101953.18753-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a user specifies an invalid console like 'console=tty3000',
the vt driver should prevent setting up a vt entry for that.
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Link: https://lore.kernel.org/r/20221209112737.3222509-3-svens@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use magic literals & comments but define a real field instead
for UART_IIR_FIFO_ENABLED and name also the values.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221125130509.8482-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add UART_MSR_STATUS_BITS for CD, RI, DSR & CTS. Use names for the
literal.
Don't make the define for combined flags part of UAPI.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221125130509.8482-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of literal 0x0f, add a define for enabling all IER bits the
8250 driver is interested in.
Don't make the define for combined flags part of UAPI.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221125130509.8482-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Karol Gugala <kgugala@antmicro.com>
Cc: Mateusz Holenko <mholenko@antmicro.com>
Cc: Gabriel Somlo <gsomlo@gmail.com>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Gabriel Somlo <gsomlo@gmail.com>
Link: https://lore.kernel.org/r/20221125142756.3e51a28d@endymion.delvare
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The polling liteuart_putchar() function is only called from methods
conditionally enabled by CONFIG_SERIAL_LITEUART_CONSOLE. Move its
definition closer to the console code where it is dependent on the
same config option.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-15-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch the TX path to IRQ-driven operation, while maintaining support
for polling mode via the poll timer.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-14-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for IRQ-driven RX. Support for the TX path will be added
in a separate commit.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-13-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move definitions for liteuart_[stop|start]_tx(), liteuart_stop_rx(),
and liteuart_putchar() to a more convenient location in preparation
for adding IRQ support. This patch contains no functional changes.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-12-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the rx loop into its own dedicated function, and (for now)
call it from the poll timer. This is in preparation for adding irq
support to the receive path.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-11-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `status` variable will always be `1` when passed into the call
to `uart_insert_char()`, so it can be eliminated altogether.
Use `u8` as the type for `ch`, as it matches the return type of
the `litex_read8()` call which produces its value.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-10-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simply provide the hard-coded TTY_NORMAL flag to uart_insert_char()
directly -- no need to dedicate a variable for that exclusive purpose.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-9-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While receiving characters, it is necessary to acknowledge each one
by writing to the EV_PENDING register's EV_RX bit. Ensure we do not
also gratuitously set the EV_TX bit in the process.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-8-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling tty_flip_buffer_push() for each individual received character
is overkill. Move it out of the rx loop, and only call it once per
set of characters received together.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-7-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove regshift and iobase port fields, since they are unused
by the driver.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-5-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove stub uart_ops methods that are not called unconditionally
from serial_core.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123130500.1030189-4-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that earlycon semihost driver works on RISC-V too, let's use a
much more generic name for the driver.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Tested-by: Sergey Matyukevich <sergey.matyukevich@syntacore.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Link: https://lore.kernel.org/r/20221209150437.795918-4-bmeng@tinylab.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some platforms, namely AMD Picasso, use non standard uart clocks (48M),
witch makes it impossible to use with earlycon.
Let the user select its own frequency.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221123-serial-clk-v3-1-49c516980ae0@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Requesting an interrupt with IRQF_ONESHOT will run the primary handler
in the hard-IRQ context even in the force-threaded mode. The
force-threaded mode is used by PREEMPT_RT in order to avoid acquiring
sleeping locks (spinlock_t) in hard-IRQ context. This combination
makes it impossible and leads to "sleeping while atomic" warnings.
Use one interrupt handler for both handlers (primary and secondary)
and drop the IRQF_ONESHOT flag which is not needed.
Fixes: e359b4411c ("serial: stm32: fix threaded interrupt handling")
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Valentin Caron <valentin.caron@foss.st.com> # V3
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230112180417.25595-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In RS485 mode the transmission of a high priority character fails since it
is written to the data register before the transmitter is enabled. Fix this
in pl011_tx_chars() by enabling RS485 transmission before writing the
character.
Fixes: 8d47923772 ("serial: amba-pl011: add RS485 support")
Cc: stable@vger.kernel.org
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20230108181735.10937-1-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A local variable sg is used to store scatterlist pointer in
pch_dma_tx_complete(). The for loop doing Tx byte accounting before
dma_unmap_sg() alters sg in its increment statement. Therefore, the
pointer passed into dma_unmap_sg() won't match to the one given to
dma_map_sg().
To fix the problem, use priv->sg_tx_p directly in dma_unmap_sg()
instead of the local variable.
Fixes: da3564ee02 ("pch_uart: add multi-scatter processing")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230103093435.4396-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver's probe allocates memory for RX FIFO (port->rx_fifo) based on
default RX FIFO depth, e.g. 16. Later during serial startup the
qcom_geni_serial_port_setup() updates the RX FIFO depth
(port->rx_fifo_depth) to match real device capabilities, e.g. to 32.
The RX UART handle code will read "port->rx_fifo_depth" number of words
into "port->rx_fifo" buffer, thus exceeding the bounds. This can be
observed in certain configurations with Qualcomm Bluetooth HCI UART
device and KASAN:
Bluetooth: hci0: QCA Product ID :0x00000010
Bluetooth: hci0: QCA SOC Version :0x400a0200
Bluetooth: hci0: QCA ROM Version :0x00000200
Bluetooth: hci0: QCA Patch Version:0x00000d2b
Bluetooth: hci0: QCA controller version 0x02000200
Bluetooth: hci0: QCA Downloading qca/htbtfw20.tlv
bluetooth hci0: Direct firmware load for qca/htbtfw20.tlv failed with error -2
Bluetooth: hci0: QCA Failed to request file: qca/htbtfw20.tlv (-2)
Bluetooth: hci0: QCA Failed to download patch (-2)
==================================================================
BUG: KASAN: slab-out-of-bounds in handle_rx_uart+0xa8/0x18c
Write of size 4 at addr ffff279347d578c0 by task swapper/0/0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.1.0-rt5-00350-gb2450b7e00be-dirty #26
Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
Call trace:
dump_backtrace.part.0+0xe0/0xf0
show_stack+0x18/0x40
dump_stack_lvl+0x8c/0xb8
print_report+0x188/0x488
kasan_report+0xb4/0x100
__asan_store4+0x80/0xa4
handle_rx_uart+0xa8/0x18c
qcom_geni_serial_handle_rx+0x84/0x9c
qcom_geni_serial_isr+0x24c/0x760
__handle_irq_event_percpu+0x108/0x500
handle_irq_event+0x6c/0x110
handle_fasteoi_irq+0x138/0x2cc
generic_handle_domain_irq+0x48/0x64
If the RX FIFO depth changes after probe, be sure to resize the buffer.
Fixes: f9d690b6ec ("tty: serial: qcom_geni_serial: Allocate port->rx_fifo buffer in probe")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221221164022.1087814-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A remove callback just returning 0 is equivalent to no remove callback
at all. So drop the useless function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221212212037.3773636-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several mutexes are taken while setting up console serial ports. In
particular, the tty_port->mutex and @console_mutex are taken:
serial_pnp_probe
serial8250_register_8250_port
uart_add_one_port (locks tty_port->mutex)
uart_configure_port
register_console (locks @console_mutex)
In order to synchronize kgdb's tty_find_polling_driver() with
register_console(), commit 6193bc9084 ("tty: serial: kgdboc:
synchronize tty_find_polling_driver() and register_console()") takes
the @console_mutex. However, this leads to the following call chain
(with locking):
platform_probe
kgdboc_probe
configure_kgdboc (locks @console_mutex)
tty_find_polling_driver
uart_poll_init (locks tty_port->mutex)
uart_set_options
This is clearly deadlock potential due to the reverse lock ordering.
Since uart_set_options() requires holding @console_mutex in order to
serialize early initialization of the serial-console lock, take the
@console_mutex in uart_poll_init() instead of configure_kgdboc().
Since configure_kgdboc() was using @console_mutex for safe traversal
of the console list, change it to use the SRCU iterator instead.
Add comments to uart_set_options() kerneldoc mentioning that it
requires holding @console_mutex (aka the console_list_lock).
Fixes: 6193bc9084 ("tty: serial: kgdboc: synchronize tty_find_polling_driver() and register_console()")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
[pmladek@suse.com: Export console_srcu_read_lock_is_held() to fix build kgdboc as a module.]
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20230112161213.1434854-1-john.ogness@linutronix.de
A number of device drivers reference CONFIG_ARM_S3C24XX_CPUFREQ or
similar symbols that are no longer available with the platform gone,
though the drivers themselves are still used on newer platforms,
so remove these hacks.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCY76ohgAKCRCAXGG7T9hj
vo8fAP0XJ94B7asqcN4W3EyeyfqxUf1eZvmWRhrbKqpLnmHLaQEA/uJBkXL49Zj7
TTcbxR1coJ/hPwhtmONU4TNtCZ+RXw0=
=2Ib5
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.2-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- two cleanup patches
- a fix of a memory leak in the Xen pvfront driver
- a fix of a locking issue in the Xen hypervisor console driver
* tag 'for-linus-6.2-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pvcalls: free active map buffer on pvcalls_front_free_map
hvc/xen: lock console list traversal
x86/xen: Remove the unused function p2m_index()
xen: make remove callback of xen driver void returned
The currently lockless access to the xen console list in
vtermno_to_xencons() is incorrect, as additions and removals from the
list can happen anytime, and as such the traversal of the list to get
the private console data for a given termno needs to happen with the
lock held. Note users that modify the list already do so with the
lock taken.
Adjust current lock takers to use the _irq{save,restore} helpers,
since the context in which vtermno_to_xencons() is called can have
interrupts disabled. Use the _irq{save,restore} set of helpers to
switch the current callers to disable interrupts in the locked region.
I haven't checked if existing users could instead use the _irq
variant, as I think it's safer to use _irq{save,restore} upfront.
While there switch from using list_for_each_entry_safe to
list_for_each_entry: the current entry cursor won't be removed as
part of the code in the loop body, so using the _safe variant is
pointless.
Fixes: 02e19f9c7c ('hvc_xen: implement multiconsole support')
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/20221130163611.14686-1-roger.pau@citrix.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown". After a timer is set to this state, then it can no
longer be re-armed.
The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed. It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.
This was created by using a coccinelle script and the following
commands:
$ cat timer.cocci
@@
expression ptr, slab;
identifier timer, rfield;
@@
(
- del_timer(&ptr->timer);
+ timer_shutdown(&ptr->timer);
|
- del_timer_sync(&ptr->timer);
+ timer_shutdown_sync(&ptr->timer);
)
... when strict
when != ptr->timer
(
kfree_rcu(ptr, rfield);
|
kmem_cache_free(slab, ptr);
|
kfree(ptr);
)
$ spatch timer.cocci . > /tmp/t.patch
$ patch -p1 < /tmp/t.patch
Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the set of driver core and kernfs changes for 6.2-rc1.
The "big" change in here is the addition of a new macro,
container_of_const() that will preserve the "const-ness" of a pointer
passed into it.
The "problem" of the current container_of() macro is that if you pass in
a "const *", out of it can comes a non-const pointer unless you
specifically ask for it. For many usages, we want to preserve the
"const" attribute by using the same call. For a specific example, this
series changes the kobj_to_dev() macro to use it, allowing it to be used
no matter what the const value is. This prevents every subsystem from
having to declare 2 different individual macros (i.e.
kobj_const_to_dev() and kobj_to_dev()) and having the compiler enforce
the const value at build time, which having 2 macros would not do
either.
The driver for all of this have been discussions with the Rust kernel
developers as to how to properly mark driver core, and kobject, objects
as being "non-mutable". The changes to the kobject and driver core in
this pull request are the result of that, as there are lots of paths
where kobjects and device pointers are not modified at all, so marking
them as "const" allows the compiler to enforce this.
So, a nice side affect of the Rust development effort has been already
to clean up the driver core code to be more obvious about object rules.
All of this has been bike-shedded in quite a lot of detail on lkml with
different names and implementations resulting in the tiny version we
have in here, much better than my original proposal. Lots of subsystem
maintainers have acked the changes as well.
Other than this change, included in here are smaller stuff like:
- kernfs fixes and updates to handle lock contention better
- vmlinux.lds.h fixes and updates
- sysfs and debugfs documentation updates
- device property updates
All of these have been in the linux-next tree for quite a while with no
problems, OTHER than some merge issues with other trees that should be
obvious when you hit them (block tree deletes a driver that this tree
modifies, iommufd tree modifies code that this tree also touches). If
there are merge problems with these trees, please let me know.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY5wz3A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yks0ACeKYUlVgCsER8eYW+x18szFa2QTXgAn2h/VhZe
1Fp53boFaQkGBjl8mGF8
=v+FB
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core and kernfs changes for 6.2-rc1.
The "big" change in here is the addition of a new macro,
container_of_const() that will preserve the "const-ness" of a pointer
passed into it.
The "problem" of the current container_of() macro is that if you pass
in a "const *", out of it can comes a non-const pointer unless you
specifically ask for it. For many usages, we want to preserve the
"const" attribute by using the same call. For a specific example, this
series changes the kobj_to_dev() macro to use it, allowing it to be
used no matter what the const value is. This prevents every subsystem
from having to declare 2 different individual macros (i.e.
kobj_const_to_dev() and kobj_to_dev()) and having the compiler enforce
the const value at build time, which having 2 macros would not do
either.
The driver for all of this have been discussions with the Rust kernel
developers as to how to properly mark driver core, and kobject,
objects as being "non-mutable". The changes to the kobject and driver
core in this pull request are the result of that, as there are lots of
paths where kobjects and device pointers are not modified at all, so
marking them as "const" allows the compiler to enforce this.
So, a nice side affect of the Rust development effort has been already
to clean up the driver core code to be more obvious about object
rules.
All of this has been bike-shedded in quite a lot of detail on lkml
with different names and implementations resulting in the tiny version
we have in here, much better than my original proposal. Lots of
subsystem maintainers have acked the changes as well.
Other than this change, included in here are smaller stuff like:
- kernfs fixes and updates to handle lock contention better
- vmlinux.lds.h fixes and updates
- sysfs and debugfs documentation updates
- device property updates
All of these have been in the linux-next tree for quite a while with
no problems"
* tag 'driver-core-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (58 commits)
device property: Fix documentation for fwnode_get_next_parent()
firmware_loader: fix up to_fw_sysfs() to preserve const
usb.h: take advantage of container_of_const()
device.h: move kobj_to_dev() to use container_of_const()
container_of: add container_of_const() that preserves const-ness of the pointer
driver core: fix up missed drivers/s390/char/hmcdrv_dev.c class.devnode() conversion.
driver core: fix up missed scsi/cxlflash class.devnode() conversion.
driver core: fix up some missing class.devnode() conversions.
driver core: make struct class.devnode() take a const *
driver core: make struct class.dev_uevent() take a const *
cacheinfo: Remove of_node_put() for fw_token
device property: Add a blank line in Kconfig of tests
device property: Rename goto label to be more precise
device property: Move PROPERTY_ENTRY_BOOL() a bit down
device property: Get rid of __PROPERTY_ENTRY_ARRAY_EL*SIZE*()
kernfs: fix all kernel-doc warnings and multiple typos
driver core: pass a const * into of_device_uevent()
kobject: kset_uevent_ops: make name() callback take a const *
kobject: kset_uevent_ops: make filter() callback take a const *
kobject: make kobject_namespace take a const *
...
Here is the "big" set of tty/serial driver changes for 6.2-rc1.
As in previous kernel releases, nothing big here at all, just some small
incremental serial/tty layer cleanups and some individual driver
additions and fixes. Highlights are:
- serial helper macros from Jiri Slaby to reduce the amount of
duplicated code in serial drivers
- api cleanups and consolidations from Ilpo Järvinen in lots of serial
drivers
- the usual set of n_gsm fixes from Daniel Starke as that code gets
exercised more
- TIOCSTI is finally able to be disabled if requested (security
hardening feature from Kees Cook)
- fsl_lpuart driver fixes and features added
- other small serial driver additions and fixes
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY5wt5A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynSiACffLCC9SFnP1ClJJh73OpCN11alDAAoIfMct2A
/zrJ4on7o0YQU1Ilg2+k
=eD/I
-----END PGP SIGNATURE-----
Merge tag 'tty-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the "big" set of tty/serial driver changes for 6.2-rc1.
As in previous kernel releases, nothing big here at all, just some
small incremental serial/tty layer cleanups and some individual driver
additions and fixes. Highlights are:
- serial helper macros from Jiri Slaby to reduce the amount of
duplicated code in serial drivers
- api cleanups and consolidations from Ilpo Järvinen in lots of
serial drivers
- the usual set of n_gsm fixes from Daniel Starke as that code gets
exercised more
- TIOCSTI is finally able to be disabled if requested (security
hardening feature from Kees Cook)
- fsl_lpuart driver fixes and features added
- other small serial driver additions and fixes
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (97 commits)
serial: atmel: don't stop the transmitter when doing PIO
serial: atmel: cleanup atmel_start+stop_tx()
tty: serial: fsl_lpuart: switch to new dmaengine_terminate_* API
serial: sunsab: Fix error handling in sunsab_init()
serial: altera_uart: fix locking in polling mode
serial: pch: Fix PCI device refcount leak in pch_request_dma()
tty: serial: fsl_lpuart: Use pm_ptr() to avoid need to make pm __maybe_unused
tty: serial: fsl_lpuart: Add runtime pm support
tty: serial: fsl_lpuart: enable wakeup source for lpuart
serdev: Replace poll loop by readx_poll_timeout() macro
tty: synclink_gt: unwind actions in error path of net device open
serial: stm32: move dma_request_chan() before clk_prepare_enable()
dt-bindings: serial: xlnx,opb-uartlite: Drop 'contains' from 'xlnx,use-parity'
serial: pl011: Do not clear RX FIFO & RX interrupt in unthrottle.
serial: amba-pl011: avoid SBSA UART accessing DMACR register
tty: serial: altera_jtaguart: remove struct altera_jtaguart
tty: serial: altera_jtaguart: use uart_port::read_status_mask
tty: serial: altera_jtaguart: remove unused altera_jtaguart::sigs
tty: serial: altera_jtaguart: remove flag from altera_jtaguart_rx_chars()
n_tty: Rename tail to old_tail in n_tty_read()
...
Since commit fc7a6209d5 ("bus: Make remove callback return void")
forces bus_type::remove be void-returned, it doesn't make much sense for
any bus based driver implementing remove callbalk to return non-void to
its caller.
This change is for xen bus based drivers.
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Dawei Li <set_pte_at@outlook.com>
Link: https://lore.kernel.org/r/TYCP286MB23238119AB4DF190997075C9CAE39@TYCP286MB2323.JPNP286.PROD.OUTLOOK.COM
Signed-off-by: Juergen Gross <jgross@suse.com>
-----BEGIN PGP SIGNATURE-----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=1PTZ
-----END PGP SIGNATURE-----
Merge tag 'printk-for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Add NMI-safe SRCU reader API. It uses atomic_inc() instead of
this_cpu_inc() on strong load-store architectures.
- Introduce new console_list_lock to synchronize a manipulation of the
list of registered consoles and their flags.
This is a first step in removing the big-kernel-lock-like behavior of
console_lock(). This semaphore still serializes console->write()
calbacks against:
- each other. It primary prevents potential races between early
and proper console drivers using the same device.
- suspend()/resume() callbacks and init() operations in some
drivers.
- various other operations in the tty/vt and framebufer
susbsystems. It is likely that console_lock() serializes even
operations that are not directly conflicting with the
console->write() callbacks here. This is the most complicated
big-kernel-lock aspect of the console_lock() that will be hard
to untangle.
- Introduce new console_srcu lock that is used to safely iterate and
access the registered console drivers under SRCU read lock.
This is a prerequisite for introducing atomic console drivers and
console kthreads. It will reduce the complexity of serialization
against normal consoles and console_lock(). Also it should remove the
risk of deadlock during critical situations, like Oops or panic, when
only atomic consoles are registered.
- Check whether the console is registered instead of enabled on many
locations. It was a historical leftover.
- Cleanly force a preferred console in xenfb code instead of a dirty
hack.
- A lot of code and comment clean ups and improvements.
* tag 'printk-for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux: (47 commits)
printk: htmldocs: add missing description
tty: serial: sh-sci: use setup() callback for early console
printk: relieve console_lock of list synchronization duties
tty: serial: kgdboc: use console_list_lock to trap exit
tty: serial: kgdboc: synchronize tty_find_polling_driver() and register_console()
tty: serial: kgdboc: use console_list_lock for list traversal
tty: serial: kgdboc: use srcu console list iterator
proc: consoles: use console_list_lock for list iteration
tty: tty_io: use console_list_lock for list synchronization
printk, xen: fbfront: create/use safe function for forcing preferred
netconsole: avoid CON_ENABLED misuse to track registration
usb: early: xhci-dbc: use console_is_registered()
tty: serial: xilinx_uartps: use console_is_registered()
tty: serial: samsung_tty: use console_is_registered()
tty: serial: pic32_uart: use console_is_registered()
tty: serial: earlycon: use console_is_registered()
tty: hvc: use console_is_registered()
efi: earlycon: use console_is_registered()
tty: nfcon: use console_is_registered()
serial_core: replace uart_console_enabled() with uart_console_registered()
...
When setting up the early console, the setup() callback of the
regular console is used. It is called manually before registering
the early console instead of providing a setup() callback for the
early console. This is probably because the early setup needs a
different @options during the early stage.
The issue here is that the setup() callback is called without the
console_list_lock held and functions such as uart_set_options()
expect that.
Rather than manually calling the setup() function before registering,
provide an early console setup() callback that will use the different
early options. This ensures that the error checking, ordering, and
locking context when setting up the early console are correct.
Since this early console can only be registered via the earlyprintk=
parameter, the @options argument of the setup() callback will always
be NULL. Rather than simply ignoring the argument, add a WARN_ON()
to get our attention in case the setup() callback semantics should
change in the future.
Note that technically the current implementation works because it is
only used in early boot. And since the early console setup is
performed before registering, it cannot race with anything and thus
does not need any locking. However, longterm maintenance is easier
when drivers rely on the subsystem API rather than manually
implementing steps that could cause breakage in the future.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-41-john.ogness@linutronix.de
kgdboc_earlycon_init() uses the console_lock to ensure that no consoles
are unregistered until the kgdboc_earlycon is setup. The console_list_lock
should be used instead because list synchronization responsibility will
be removed from the console_lock in a later change.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-39-john.ogness@linutronix.de
Calling tty_find_polling_driver() can lead to uart_set_options() being
called (via the poll_init() callback of tty_operations) to configure the
uart. But uart_set_options() can also be called by register_console()
(via the setup() callback of console).
Take the console_list_lock to synchronize against register_console() and
also use it for console list traversal. This also ensures the console list
cannot change until the polling console has been chosen.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-38-john.ogness@linutronix.de
configure_kgdboc() uses the console_lock for console list iteration. Use
the console_list_lock instead because list synchronization responsibility
will be removed from the console_lock in a later change.
The SRCU iterator could have been used here, but a later change will
relocate the locking of the console_list_lock to also provide
synchronization against register_console().
Note, the console_lock is still needed to serialize the device()
callback with other console operations.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-37-john.ogness@linutronix.de
Use srcu console list iteration for safe console list traversal.
Note that this is a preparatory change for when console_lock no
longer provides synchronization for the console list.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-36-john.ogness@linutronix.de
