This patch move the credit map setting to right place to avoid
brcmf_fws_return_credits() return without setting the credit map.
It fix the thoughput zero stalls issue in softAP mode when STA
using PM 1 mode.
Signed-off-by: Double Lo <double.lo@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-6-chi-hsien.lin@cypress.com
There is a mismatch of tx status flag values between host and firmware.
It makes the host mistake the flags and have incorrect behavior of credit
returns. So update the flags to sync with the firmware ones.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-5-chi-hsien.lin@cypress.com
It is observed that sometimes when sdiod is low in tx credits in low
rssi scenarios, the data path consumes all sdiod rx all credits and
there is no sdiod rx credit available for control path causing host
and card to go out of sync resulting in link loss between host and
card. So in order to prevent it some credits are reserved for control
path.
Note that TXCTL_CREDITS can't be larger than the firmware default
credit update threshold 2; otherwise there will be a deadlock for both
side waiting for each other.
Signed-off-by: Amar Shankar <amsr@cypress.com>
Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-4-chi-hsien.lin@cypress.com
In wifi firmware, max length of IOCTL/IOVAR buffer size is 8192.
Increase the message buffer max size same as wifi firmware for control
packets so return buffers can come back.
Signed-off-by: Soontak Lee <soontak.lee@cypress.com>
Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-3-chi-hsien.lin@cypress.com
Current credit borrowing allows only the access category BE to
borrow the credits. This change is to fix the credit borrowing
logic, to make borrowing available for all access categories
and also to borrow only from the lower categories. This fixes WFA
802.11n certs 5.2.27 failures.
Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200610152106.175257-2-chi-hsien.lin@cypress.com
Bss info flag definition need to be fixed from 0x2 to 0x4
This flag is for rssi info received on channel.
All Firmware branches defined as 0x4 and this is bug in brcmfmac.
Signed-off-by: Prasanna Kerekoppa <prasanna.kerekoppa@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-6-wright.feng@cypress.com
The firmware state machines are not fully suitable for concurrent
station interface support, it may hit unexpected error if we have 2
different SSIDs and the roaming scenarios concurrently.
To avoid the bad user-experience if this is not fully validated, we
dis-allow user to create two concurrent station interfaces.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-5-wright.feng@cypress.com
brcmfmac host driver makes SDIO bus sleep and stops SDIO watchdog if no
pending event or data. As a result, host driver does not poll firmware
console buffer before buffer overflow, which leads to missing firmware
logs. We should not stop SDIO watchdog if console_interval is non-zero
in debug build.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-4-wright.feng@cypress.com
When host driver retrieves mac addresses from dongle, driver copies memory
from drvr->mac to perm_addr. But at the moment, drvr->mac is all zero
array which causes permanent MAC address in wiphy is all zero as well.
To fix this, we set drvr->mac before setting perm_addr.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-3-wright.feng@cypress.com
To truncate the additional bytes, if extra bytes have been received.
Current code only have a warning and proceed without handling it.
But in one of the crash reported by DVT, these causes the
crash intermittently. So the processing is limit to the skb->len.
Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200604071835.3842-2-wright.feng@cypress.com
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
Set MES watermark size to 0x50 for 43012. It fixes SDIO bus hang issue
when running at high throughput.
Signed-off-by: Double Lo <double.lo@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529034938.124533-6-chi-hsien.lin@cypress.com
Set F2 blocksize to 256 bytes and watermark to 0x40 for 4354/4356 SDIO.
Also enable and configure F1 MesBusyCtrl. It would resolve random driver
crash issue.
Signed-off-by: Frank Kao <frank.kao@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529034938.124533-4-chi-hsien.lin@cypress.com
Set F2 blocksize to 256 bytes for 4373. It fixes DMA error while having
UDP bi-directional traffic. Also use a defined F1 MesBusyCtrl value.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529034938.124533-2-chi-hsien.lin@cypress.com
All macro names for SDIO device IDs are prefixed by vendor name to which
device ID belongs. So for consistency add Broadcom string vendor prefix to
all Cypress macro names as they belong to SDIO Broadcom vendor ID.
Change also Cypress 43012 value from decimal do hexadecimal notation to be
consistent with all other values.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-11-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
-----BEGIN PGP SIGNATURE-----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=MVBJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
One batch of changes, containing:
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
An incorrect value of use_fwsup is set for 4-way handshake offload for
WPA//WPA2-PSK, caused by commit 3b1e0a7bdf ("brcmfmac: add support for
SAE authentication offload"). It results in missing bit
BRCMF_VIF_STATUS_EAP_SUCCESS set in brcmf_is_linkup() and causes the
failure. This patch correct the value for the case.
Also setting bit BRCMF_VIF_STATUS_EAP_SUCCESS for SAE offload case in
brcmf_is_linkup() to fix SAE offload failure.
Fixes: 3b1e0a7bdf ("brcmfmac: add support for SAE authentication offload")
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1589277788-119966-1-git-send-email-chi-hsien.lin@cypress.com
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:1785:5-8:
WARNING: Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200508074351.19193-1-yanaijie@huawei.com
Fix sparse warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c:2206:5:
warning: symbol 'brcmf_p2p_get_conn_idx' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Reviewed-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200508013249.95196-1-chenzhou10@huawei.com
When plumbing rxiv for (GTK) keys, current code does not use seq/seq_len
when present nor set iv_initialized for iovar wsec_key. This could
result in missing broadcast traffic after GTK rekey. The fix is setting
iv_initialized and using seq/seq_len for iovar wsec_key.
Signed-off-by: Soontak Lee <soontak.lee@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588770201-54361-4-git-send-email-wright.feng@cypress.com
The driver sends an action frame down and waits for dwell time to be
completed or aborted before sending out the next action frame.
Driver issues "scan abort" to cancel the current time slot, but this
doesn't have any effect because, we are not using scan engine for
sending action frame.
Fix is to use "actframe_abort" to cancels the current action frame.
Signed-off-by: Ryohei Kondo <ryohei.kondo@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588770201-54361-3-git-send-email-wright.feng@cypress.com
Host driver parses and sets security params into FW passed by
supplicant. This has to be done after reiniting interface in the
firmware.
Signed-off-by: Jia-Shyr Chuang <joseph.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588770201-54361-2-git-send-email-wright.feng@cypress.com
802.1d defines 0,3 for BE and 1,2 for BK. In pcie dongles, 0 & 3 are
mapped to 0 and 1,2 are mapped to 1. This change corrects this mapping,
so that BE & BK are given access precedence accordingly by pcie dongles.
Signed-off-by: Pramod Prakash <pramod.prakash@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588661487-21884-3-git-send-email-chi-hsien.lin@cypress.com
In WLAN, priority among various access categories of traffic is
always set by the AP using WMM parameters and this may not always
follow the standard 802.1d priority.
In this change, priority is adjusted based on the AP WMM params
received as part of the Assoc Response and the same is later used
to map the priority of all incoming traffic.
In a specific scenario where EDCA parameters are configured to be same
for all ACs, use the default FW priority definition to avoid queuing
packets of all ACs to the same priority queue.
This change fixes the following 802.11 certification tests:
* 11n - 5.2.31 ACM Bit Conformance test
* 11n - 5.2.32 AC Parameter Modification test
* 11ac - 5.2.33 TXOP Limit test
Signed-off-by: Saravanan Shanmugham <saravanan.shanmugham@cypress.com>
Signed-off-by: Justin Li <justin.li@cypress.com>
Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588661487-21884-2-git-send-email-chi-hsien.lin@cypress.com
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJetAhAAAoJEG4XJFUm622bADEH/A1OjAD3H1iZyTmXHP4T7yZe
TKJ+9I6B3BDR1czUTm+kUhrgBDNpdLLtu+b+5QXfpPLrtZ0FF/zjuazgueyqQpZ1
zudj+rG72njHpU0RKtO7wIBrCtckLPV0be+3026hztatJmJ7XQ9FvsanFPPsrrNv
0lh8E8kDUSynOW2me8FW1GBgDkGaBaicAs4FSjwNJC31Wo/VN5m9gEFkGpT1VJWP
l0xeEQ/N2mknQVuTR4CuMT9VJ0SNlJrLZpBVAqkmc170c3pKChl3LTNCnP925ye9
Nfqw2sQKgUPJKRbZR5wZTphGuu4krFv0ldWCvb0oFtZlCLIkiOz6+AA7b33oV2A=
=7ewK
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-05-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.8
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:1060:6-12:
WARNING: Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504113357.41422-1-yanaijie@huawei.com
It was observed that P2P Cert. 5.1.19: DEVUT responds to Service
Discovery request failed due to DUT did not send GAS Comeback Response
after receiving request from test bed P2P peer. To fix this issue,
we need to add P2P Action Frame retry delay to enhance P2P connection
under VSDB and noisy environment, since the peer can be in other
channels under VSDB.
Signed-off-by: Justin Li <Justin.Li@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588572453-194663-4-git-send-email-wright.feng@cypress.com
P2P group formation fails since either peer is not able to send go-neg
confirm or dut is not able to send go-neg response. To fix this, retry
limit should be increased and dwell time check should be added.
Signed-off-by: Joseph Chuang <joseph.chuang@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588572453-194663-3-git-send-email-wright.feng@cypress.com
With RSDB feature, firmware is able to support two P2P-AGO or two
P2P-GC at the same time. So we add the second p2p connection type
to map to the second P2P connection bsscfg.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588572453-194663-2-git-send-email-wright.feng@cypress.com
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
In doing this, make brcmf_debugfs_add_entry() return void as no one was
even paying attention to the return value.
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafał Miłecki" <rafal@milecki.pl>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200429101526.GA2094124@kroah.com
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:2359:6-40:
WARNING: Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426094053.23132-1-yanaijie@huawei.com
Miracast Certification clause 6.1.2 may fail if there is no WFD IE in
p2p assoc response. This change allows WFD IE to be added to p2p assoc
response.
Related WFA certification:
6.1.2 P-SnUT operating as a Group Owner accepts a WFD Session with a
Reference Source
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Ryohei Kondo <ryohei.kondo@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-6-git-send-email-chi-hsien.lin@cypress.com
P2p spec mentioned that the p2p device address should be the globally
administered address with locally administered bit set. Therefore,
follow this guideline by default.
When the primary interface is set to a locally administered address, the
locally administered bit cannot be set again. Generate a random locally
administered address for this case.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-5-git-send-email-chi-hsien.lin@cypress.com
Send p2p presence response from the p2p interface address instead
of the p2p device address. This is needed for p2p cert 6.1.9 to pass.
Signed-off-by: Madhan Mohan R <MadhanMohan.R@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-4-git-send-email-chi-hsien.lin@cypress.com
The firmware does not respond ARP request and causes ping failure with
following steps:
1. Bring up interface
ifconfig wlan0 up or start wpa_supplicant
2. Set the IP address
ifconfig wlan0 192.168.100.10
3. Bring down interface or
ifconfig wlan0 down or kill wpa_supplicant
4. Bring up interface again and set the same IP address
5. Connect to AP(192.168.100.1) and ping to AP will be failed.
FMAC clears arp_hostip when bringing down the interface, but not set it
back if setting the same IP address. We are able to see the IP address
in interface info(inconfig wlan0) but the ping still cannot work because
the firmware ARP offload does not respond the ARP request.
Because of that, we remove "arp_hostip_clear" from function
"brcmf_netdev_stop"
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-3-git-send-email-chi-hsien.lin@cypress.com
When starting station mode on wlan0 and AP mode on wlan1, the apsta will
be disabled and cause data stall on wlan0(station). The apsta feature
with MCHAN(Multi-Channel Concurrent) or RSDB(Real Simultaneous
Dual-Band) can make STA+AP work on two bands concurrently.
Because of that, we keep apsta enabled if firmware supports MCHAN or
RSDB features
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-2-git-send-email-chi-hsien.lin@cypress.com
Almost all drivers below cfg80211 get the API wrong (except for
cfg80211) and are unable to cope with multiple registrations for
the same frame type, which is valid due to the match filter.
This seems to indicate the API is wrong, and we should maintain
the full information in cfg80211 instead of the drivers.
Change the API to no longer inform the driver about individual
registrations and unregistrations, but rather every time about
the entire state of the entire wiphy and single wdev, whenever
it may have changed. This also simplifies the code in cfg80211
as it no longer has to track exactly what was unregistered and
can free things immediately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200417124300.f47f3828afc8.I7f81ef59c2c5a340d7075fb3c6d0e08e8aeffe07@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/stf.c:309:5-13:
Unneeded variable: "ret_code". Return "0" on line 328
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200413082126.22572-1-yanaijie@huawei.com
Sparse reports a warning at brcms_down()
warning: context imbalance in brcms_down()
- unexpected unlock
The root cause is the missing annotation at brcms_down()
Add the missing __must_hold(&wl->lock) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200411001933.10072-6-jbi.octave@gmail.com
Sparse reports a warning at brcms_rfkill_set_hw_state()
warning: context imbalance in brcms_rfkill_set_hw_state()
- unexpected unlock
The root cause is the missing annotation at brcms_rfkill_set_hw_state()
Add the missing __must_hold(&wl->lock) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200411001933.10072-5-jbi.octave@gmail.com
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:3773:5-8:
Unneeded variable: "err". Return "0" on line 3781
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200410090817.26883-1-yanaijie@huawei.com
Pointer 'address' is being assigned and updated in a few places
by it is never read. Hence the assignments are redundant and can
be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200405133906.381358-1-colin.king@canonical.com
sup_wpa feature is getting after setting feature_disable flag.
If firmware is supported sup_wpa feature, it's always enabled
regardless of feature_disable flag.
Fixes: b8a64f0e96 ("brcmfmac: support 4-way handshake offloading for WPA/WPA2-PSK")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200330052528.10503-1-jh80.chung@samsung.com
We add enable dynamic suspend (autosuspend) support in host driver, and
it can let platform cut down idle power consumption.
To support autosuspend feature in host driver, kernel need to be built
with CONFIG_USB_SUSPEND and autosuspend need to be turn on.
And we also replace wowl feature with adding "needs_remote_wakeup", so
that host still can be waken by wireless device.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585124429-97371-6-git-send-email-chi-hsien.lin@cypress.com
Will enable FMAC to push more packets to bus tx queue and help
improve throughput when fws queuing is enabled. This change is
required to tune the throughput for passing WMM CERT tests.
Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585124429-97371-5-git-send-email-chi-hsien.lin@cypress.com
The function brcmf_inform_single_bss returns the value as success,
even when the length exceeds the maximum value.
The fix is to send appropriate code on this error.
This issue is observed when Cypress test group reported random fmac
crashes when running their tests and the path was identified from the
crash logs. With this fix the random failure issue in Cypress test group
was resolved.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585124429-97371-4-git-send-email-chi-hsien.lin@cypress.com
When the brcmf_fws_process_skb() fails to get hanger slot for
queuing the skb, it tries to free the skb.
But the caller brcmf_netdev_start_xmit() of that funciton frees
the packet on error return value.
This causes the double freeing and which caused the kernel crash.
Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585124429-97371-3-git-send-email-chi-hsien.lin@cypress.com
When the control transfer gets timed out, the error status
was returned without killing that urb, this leads to using
the same urb. This issue causes the kernel crash as the same
urb is sumbitted multiple times. The fix is to kill the
urb for timeout transfer before returning error
Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585124429-97371-2-git-send-email-chi-hsien.lin@cypress.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200225020804.GA9428@embeddedor
With commit 216b44000a ("brcmfmac: Fix use after free in
brcmf_sdio_readframes()") applied, we see locking timeouts in
brcmf_sdio_watchdog_thread().
brcmfmac: brcmf_escan_timeout: timer expired
INFO: task brcmf_wdog/mmc1:621 blocked for more than 120 seconds.
Not tainted 4.19.94-07984-g24ff99a0f713 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
brcmf_wdog/mmc1 D 0 621 2 0x00000000 last_sleep: 2440793077. last_runnable: 2440766827
[<c0aa1e60>] (__schedule) from [<c0aa2100>] (schedule+0x98/0xc4)
[<c0aa2100>] (schedule) from [<c0853830>] (__mmc_claim_host+0x154/0x274)
[<c0853830>] (__mmc_claim_host) from [<bf10c5b8>] (brcmf_sdio_watchdog_thread+0x1b0/0x1f8 [brcmfmac])
[<bf10c5b8>] (brcmf_sdio_watchdog_thread [brcmfmac]) from [<c02570b8>] (kthread+0x178/0x180)
In addition to restarting or exiting the loop, it is also necessary to
abort the command and to release the host.
Fixes: 216b44000a ("brcmfmac: Fix use after free in brcmf_sdio_readframes()")
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: franky.lin@broadcom.com
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 2018 13" MacBook Pro (MacBookPro15,2) has a Broadcom chip, the 4364.
This chip appears to be specific to Apple and is not found in other
hardware.
Add this chip to the brcmfmac driver so that it can be recognized
automatically. Note that the PCI device id is 4464 even though the chip
is referred to as the 4364.
Signed-off-by: brian m. carlson <sandals@crustytoothpaste.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking updates from David Miller:
1) Add WireGuard
2) Add HE and TWT support to ath11k driver, from John Crispin.
3) Add ESP in TCP encapsulation support, from Sabrina Dubroca.
4) Add variable window congestion control to TIPC, from Jon Maloy.
5) Add BCM84881 PHY driver, from Russell King.
6) Start adding netlink support for ethtool operations, from Michal
Kubecek.
7) Add XDP drop and TX action support to ena driver, from Sameeh
Jubran.
8) Add new ipv4 route notifications so that mlxsw driver does not have
to handle identical routes itself. From Ido Schimmel.
9) Add BPF dynamic program extensions, from Alexei Starovoitov.
10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes.
11) Add support for macsec HW offloading, from Antoine Tenart.
12) Add initial support for MPTCP protocol, from Christoph Paasch,
Matthieu Baerts, Florian Westphal, Peter Krystad, and many others.
13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu
Cherian, and others.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits)
net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC
udp: segment looped gso packets correctly
netem: change mailing list
qed: FW 8.42.2.0 debug features
qed: rt init valid initialization changed
qed: Debug feature: ilt and mdump
qed: FW 8.42.2.0 Add fw overlay feature
qed: FW 8.42.2.0 HSI changes
qed: FW 8.42.2.0 iscsi/fcoe changes
qed: Add abstraction for different hsi values per chip
qed: FW 8.42.2.0 Additional ll2 type
qed: Use dmae to write to widebus registers in fw_funcs
qed: FW 8.42.2.0 Parser offsets modified
qed: FW 8.42.2.0 Queue Manager changes
qed: FW 8.42.2.0 Expose new registers and change windows
qed: FW 8.42.2.0 Internal ram offsets modifications
MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver
Documentation: net: octeontx2: Add RVU HW and drivers overview
octeontx2-pf: ethtool RSS config support
octeontx2-pf: Add basic ethtool support
...
Report monitor interface availability using cfg80211 and support it in
the add_virtual_intf() and del_virtual_intf() callbacks. This new
feature is conditional and depends on firmware flagging monitor packets.
Receiving monitor frames is already handled by the brcmf_netif_mon_rx().
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move similar/duplicated code out of combination specific code blocks.
This simplifies code a bit and allows adding more combinations later.
A list of combinations remains unchanged.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 262f2b53f6 ("brcmfmac: call brcmf_attach() just before calling
brcmf_bus_started()") changed the initialization order of the brcmfmac
SDIO driver. Unfortunately since brcmf_sdiod_intr_register() is now
called before the sdiodev->bus_if initialization, it reads the wrong
chip ID and fails to initialize the GPIO on brcm43362. Thus the chip
cannot send interrupts and fails to probe:
[ 12.517023] brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout
[ 12.531214] ieee80211 phy0: brcmf_bus_started: failed: -110
[ 12.536976] ieee80211 phy0: brcmf_attach: dongle is not responding: err=-110
[ 12.566467] brcmfmac: brcmf_sdio_firmware_callback: brcmf_attach failed
Initialize the bus interface earlier to ensure that
brcmf_sdiod_intr_register() properly sets up the OOB interrupt.
BugLink: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=908438
Fixes: 262f2b53f6 ("brcmfmac: call brcmf_attach() just before calling brcmf_bus_started()")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:911:2-24: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
NVIDIA Tegra SoCs do not like when OOB wake is enabled and WiFi interface
is in DOWN state during suspend. This results in a CPU hang on programming
OOB wake-up state of the GPIO controller during of system's suspend.
The solution is trivial: don't enable wake for the OOB interrupt when it
should be disabled.
This fixes hang on Tegra20 (Acer A500) and Tegra30 (Nexus 7) devices which
are using BCM4329 and BCM4330 WiFi chips respectively.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the implementation of brcmf_usbdev_qinit() the allocated memory for
reqs is leaking if usb_alloc_urb() fails. Release reqs in the error
handling path.
Fixes: 71bb244ba2 ("brcm80211: fmac: add USB support for bcm43235/6/8 chipsets")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With RSDB mode, FMAC and firmware are able to create 2 or more AP,
so we should not set mbss in vif structure if firmware does not
support MBSS feature.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With firmware RSDB feature
1. The maximum support interface is four.
2. The maximum difference channel is two.
3. The maximum interfaces of {station/p2p client/AP} are two.
4. The maximum interface of p2p device is one.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
BCM4359 is a 2x2 802.11 abgn+ac Dual-Band HT80 combo chip and it
supports Real Simultaneous Dual Band feature.
Based on a similar patch by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
4359 dongles do not support setting roaming parameters (error -52).
Do not fail the 80211 configuration in this case.
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer 4359 chip revisions need a different rambase address.
This fixes firmware download on such devices which fails otherwise.
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set F2 blocksize to 256 bytes and watermark to 0x40 for 4359. Also
enable and configure F1 MesBusyCtrl. It fixes DMA error while having
UDP bi-directional traffic.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
[slightly adapted for rebase on mainline linux]
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are two D11 cores in RSDB chips like 4359. We have to reset two
D11 cores simutaneously before firmware download, or the firmware may
not be initialized correctly and cause "fw initialized failed" error.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 71bb244ba2 ("brcm80211: fmac: add USB support for bcm43235/6/8 chipsets")
Cc: stable <stable@vger.kernel.org> # 3.4
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's important as brcmfmac creates one main interface for each PHY and
doesn't allow deleting it. Not setting carrier could result in other
subsystems misbehaving (e.g. LEDs "netdev" trigger turning LED on).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The brcmu_pkt_buf_free_skb() function frees "pkt" so it leads to a
static checker warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:1974 brcmf_sdio_readframes()
error: dereferencing freed memory 'pkt'
It looks like there was supposed to be a continue after we free "pkt".
Fixes: 4754fceeb9 ("brcmfmac: streamline SDIO read frame routine")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As 'channel' is declared as u16, the following expression is always false.
channel < 0
So we can remove unnecessary 'always false' statement.
Signed-off-by: Austin Kim <austindh.kim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the implementation of brcmf_p2p_create_p2pdev() the allocated memory
for p2p_vif is leaked when the mac address is the same as primary
interface. To fix this, go to error path to release p2p_vif via
brcmf_free_vif().
Fixes: cb746e4783 ("brcmfmac: check p2pdev mac address uniqueness")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This fixes a minor WARNING in the cfg80211:
[ 130.658034] ------------[ cut here ]------------
[ 130.662805] WARNING: CPU: 1 PID: 610 at net/wireless/core.c:954 wiphy_unregister+0xb4/0x198 [cfg80211]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c: In function brcmf_chip_dmp_get_regaddr:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:790:5: warning: variable mpnum set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c: In function brcmf_chip_dmp_erom_scan:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:866:10: warning: variable nsp set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c: In function brcmf_chip_dmp_erom_scan:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:866:5: warning: variable nmp set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:841:7: warning: variable free_pdu set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:842:30: warning: variable tx_rts_count set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:842:6: warning: variable tx_rts set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:843:7: warning: variable totlen set but not used [-Wunused-but-set-variable]
They are never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdwYyqAAoJEG4XJFUm622b/jMH/0KUcGz8y4gkk2B2lMRyUOTu
t84LiSHxcsq6letlr/vak4S6NrxMLP8Z/ByyoKC8o3yeVsdyMNMSLZAztFFhxdXr
Haky2SM10q6vnn9s1skXS/qkHSd2WdUFT2DgYxyOPCtJUazVKjcboJ4YX/TUg99a
5eqPpZ4RXtW6uOmWHS7JXtLcCFPywKPBtMAjLEDMYOUSSBWExBNyNZNhznSS3ywY
4VKvc675gXE+WD3qXRhL8EJjyed94yuS3wYbKWp8iTaIRyluDmc5lVhjWH1A0HLE
Qb62QL8XLtbX5fcTnaupdAIXwxeIBylOBe8QtW7QUbAnGFf8bexLxfnQM+To4wI=
=24zD
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2019-11-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.5
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 518a2f1925
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware may have SAE authentication code built-in. This is
detected by the driver and indicated in the wiphy features flags.
User-space can use this flag to determine whether or not to provide
the password material for SAE authentication in the nl80211 CONNECT
command.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There really is no need to make drivers call the
ieee80211_start_tx_ba_cb_irqsafe() function and then
schedule the worker if all we want is to set a bit.
Add a new return value (that was previously considered
invalid) to indicate that the driver is immediately
ready for the session, and make drivers use it. The
only drivers that remain different are the Intel ones
as they need to negotiate more with the firmware.
Link: https://lore.kernel.org/r/1570007543-I152912660131cbab2e5d80b4218238c20f8a06e5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The nested 'li_mimo == &locale_bn' check is excessive and always
true. Thus it can be safely removed.
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmfmac assumed the wifi device always remains powered on and thus
hardcoded the MMC_PM_KEEP_POWER flag expecting the wifi device to
remain on even during suspend/resume cycles.
This is not always the case, some appliances cut power to everything
connected via SDIO for efficiency reasons and this leads to wifi not
being usable after coming out of suspend because the device was not
correctly reinitialized.
So we check for the keep_power capability and if it's not present then
we remove the device and probe it again during resume to mirror what's
happening in hardware and ensure correct reinitialization in the case
when MMC_PM_KEEP_POWER is not supported.
Suggested-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When n_reqs == 0 there is nothing to do so it doesn't make sense to
search for requests and issue a warning because none is found.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'pih' is known to be non-NULL at this point, so the test can be removed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With FT-802.1X, driver should send a port authorized event right after
sending a roamed event. It is used to indicate that a new AP is already
authorized so 802.1X is not required.
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Providing a new wiphy on every PCIe reset was confusing and was causing
configuration problems for some users (supplicant and authenticators).
Sticking to the existing wiphy should make error recovery much simpler
and more reliable.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move code allocating/freeing wiphy out of above functions. This will
allow reinitializing the driver (e.g. on some error) without allocating
a new wiphy.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This moves "ops" pointer from "struct brcmf_cfg80211_info" to the
"struct brcmf_pub". This movement makes it possible to allocate wiphy
without attaching cfg80211 (brcmf_cfg80211_attach()). It's required for
later separation of wiphy allocation and driver initialization.
While at it fix also an unlikely memory leak in the brcmf_attach().
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use %*ph format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a trivial debugfs entry for triggering reset just like in case
of firmware crash. It works by writing 1 to it:
echo 1 > reset
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case of compiling driver without DEBUG expose a stub function to make
writing debug code much simpler (no extra conditions). This will allow
e.g. using debugfs_create_file() without any magic if or #ifdef.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Getting RAM info just once per driver's lifetime (during chip
recognition) is not enough as it may get adjusted later (depending on
the used firmware). Subsequent inits may load different firmwares so a
full RAM recognition is required on every PCIe setup. This is especially
important since implementing hardware reset on a firmware crash.
Moreover calling brcmf_chip_get_raminfo() makes sure that RAM core is
up. It's important as having BCMA_CORE_SYS_MEM down on BCM4366 was
resulting in firmware failing to initialize and following error:
[ 65.657546] brcmfmac 0000:01:00.0: brcmf_pcie_download_fw_nvram: Invalid shared RAM address 0x04000001
This change makes brcmf_chip_get_raminfo() call during chip recognition
redundant for PCIe devices but SDIO and USB still need it and it's a
very small overhead anyway.
Fixes: 4684997d9e ("brcmfmac: reset PCIe bus on a firmware crash")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The strncpy() may truncate the copied string,
replace it by the safer strscpy().
To avoid below compile warning with gcc 8.2:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:In function 'brcmf_vndr_ie':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:4227:2:
warning: 'strncpy' output truncated before terminating nul copying 3 bytes from a string of the same length [-Wstringop-truncation]
strncpy(iebuf, add_del_cmd, VNDR_IE_CMD_LEN - 1);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Xulin Sun <xulin.sun@windriver.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The pointer hash is being initialized with a value that is never read
and is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In wlc_phy_radio_init_2056(), regs_SYN_2056_ptr, regs_TX_2056_ptr and
regs_RX_2056_ptr may be not assigned, and thus they are still NULL.
Then, they are used on lines 20042-20050:
wlc_phy_init_radio_regs(pi, regs_SYN_2056_ptr, (u16) RADIO_2056_SYN);
wlc_phy_init_radio_regs(pi, regs_TX_2056_ptr, (u16) RADIO_2056_TX0);
wlc_phy_init_radio_regs(pi, regs_TX_2056_ptr, (u16) RADIO_2056_TX1);
wlc_phy_init_radio_regs(pi, regs_RX_2056_ptr, (u16) RADIO_2056_RX0);
wlc_phy_init_radio_regs(pi, regs_RX_2056_ptr, (u16) RADIO_2056_RX1);
Thus, possible null-pointer dereferences may occur.
To avoid these bugs, when these variables are not assigned,
wlc_phy_radio_init_2056() directly returns.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c: In function 'brcms_c_set_gmode':
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:5257:7: warning: variable 'preamble_restrict' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:5256:6: warning: variable 'preamble' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:5251:7: warning: variable 'shortslot_restrict' set but not used [-Wunused-but-set-variable]
They are never used so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c: In function brcmf_update_bss_info:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:2962:5: warning: variable dtim_period set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c: In function brcmf_update_bss_info:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:2961:6: warning: variable beacon_interval set but not used [-Wunused-but-set-variable]
They are never used so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware crash is a pretty rare event and can't happen too frequently as
it has to be followed by a hardware reinitialization and config reload.
It should be safe to don't use net_ratelimit() when it happens.
For reporting & debugging purposes it's important to provide a complete
log as the last lines are actually the most important. This change
modifies brcmfmac to print all messages in an unlimited way in that
specific case. With this change there should be finally a backtrace of
firmware finally visible after a crash.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Recently a strcpy() was replaced by strlcpy(). However, the strcpy()
was not needed in the first place. So removing that line of code.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the bus is down, eg. due to rmmod, there is no need to
attempt to inform firmware about it.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Upon rmmod a few attempts are made to inform firmware, but there is
no point as the bus is down and these will fail. Avoid them to keep
the logs clean.
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clearing firmware events in brcmf_fweh_detach() is always failing
because it is called only upon driver remove and communication
with firmware is no longer possible.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
No point in sending a firmware command when bus is down so make it
conditional checking the state.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When brcmf_detach() from the bus layer upon rmmod we can no longer
communicate. Hence we will set the bus state to DOWN and cleanup
the event and protocol layer. The network interfaces need to be
deleted before brcmf_cfg80211_detach() because the latter does the
wiphy_unregister() which issues a warning if there are still network
devices linked to the wiphy instance.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit 5cdb0ef614. Subsequent
changes make rework the driver code fixing the issue differently.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver has custom regulatory rules which had maximum bandwidth
for 5GHz channels set to 80MHz. As a consequence the driver can
not use 160MHz in AP mode even when the device supports it. So
relax the rules allowing 160MHz. After wiphy_register() the channel
flags are updated according what the device actually supports.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the firmware supports 802.11h and the device can operate in 5GHz
band we can enable DFS_OFFLOAD extended feature.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function chandef_to_chanspec() was not handling 160MHz bandwidth
resulting in wrong encoding of the channel. That resulting in firmware
rejecting the provided channel specification.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In my previous commit to validate a policy I neglected to
actually add one to the few drivers using vendor commands,
fix that now.
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Fixes: 901bb98918 ("nl80211: require and validate vendor command policy")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
First set of patches for 5.3, but not that many patches this time.
This pull request fails to compile with the tip tree due to
ktime_get_boot_ns() API changes there. It should be easy for Linus to
fix it in p54 driver once he pulls this, an example resolution here:
https://lkml.kernel.org/r/20190625160432.533aa140@canb.auug.org.au
Major changes:
airo
* switch to use skcipher interface
p54
* support boottime in scan results
rtw88
* add fast xmit support
* add random mac address on scan support
rt2x00
* add software watchdog to detect hangs, it's disabled by default
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdE5OGAAoJEG4XJFUm622bWCoH/1bLdkTYOkSatXxpHn2cVRvA
SrQ+ZSfOWJe5d0B+9HWhO5r+Savuu+IrgcC6vSIBBVglF5Tf6F0DAxHVrIwc9MSY
QUv4f1suqeH0ipUEBWJXoDXM2OEShvw5WCuY0ZnYw2hZRI7Sb5nqwJEUH57BtBCX
tFW22Ax3ZFTmCfexFgiwEjmtEx6HHz/nleYLMt9gg7X1Twug+QmhEsNw/27PfvMx
RyVyCJ1UvW2x4GHqDRlGxQoh7FlMvuVe/v/VcjGp2Fp8s7GS0xUyA11svGBFpdnT
K94Y3LOcTSdBQwScbn6O2v6EybB9PZYhg6rckwbMgIN2pkkWqXnh5avru4U0T9k=
=yq6Q
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-06-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valu says:
====================
wireless-drivers-next patches for 5.3
First set of patches for 5.3, but not that many patches this time.
This pull request fails to compile with the tip tree due to
ktime_get_boot_ns() API changes there. It should be easy for Linus to
fix it in p54 driver once he pulls this, an example resolution here:
https://lkml.kernel.org/r/20190625160432.533aa140@canb.auug.org.au
Major changes:
airo
* switch to use skcipher interface
p54
* support boottime in scan results
rtw88
* add fast xmit support
* add random mac address on scan support
rt2x00
* add software watchdog to detect hangs, it's disabled by default
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When Broadcom SDIO cards are idled they go to sleep and a whole
separate subsystem takes over their SDIO communication. This is the
Always-On-Subsystem (AOS) and it can't handle tuning requests.
Specifically, as tested on rk3288-veyron-minnie (which reports having
BCM4354/1 in dmesg), if I force a retune in brcmf_sdio_kso_control()
when "on = 1" (aka we're transition from sleep to wake) by whacking:
bus->sdiodev->func1->card->host->need_retune = 1
...then I can often see tuning fail. In this case dw_mmc reports "All
phases bad!"). Note that I don't get 100% failure, presumably because
sometimes the card itself has already transitioned away from the AOS
itself by the time we try to wake it up. If I force retuning when "on
= 0" (AKA force retuning right before sending the command to go to
sleep) then retuning is always OK.
NOTE: we need _both_ this patch and the patch to avoid triggering
tuning due to CRC errors in the sleep/wake transition, AKA ("brcmfmac:
sdio: Disable auto-tuning around commands expected to fail"). Though
both patches handle issues with Broadcom's AOS, the problems are
distinct:
1. We want to defer (but not ignore) asynchronous (like
timer-requested) tuning requests till the card is awake. However,
we want to ignore CRC errors during the transition, we don't want
to queue deferred tuning request.
2. You could imagine that the AOS could implement retuning but we
could still get errors while transitioning in and out of the AOS.
Similarly you could imagine a seamless transition into and out of
the AOS (with no CRC errors) even if the AOS couldn't handle
tuning.
ALSO NOTE: presumably there is never a desperate need to retune in
order to wake up the card, since doing so is impossible. Luckily the
only way the card can get into sleep state is if we had a good enough
tuning to send it the command to put it into sleep, so presumably that
"good enough" tuning is enough to wake us up, at least with a few
retries.
Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are certain cases, notably when transitioning between sleep and
active state, when Broadcom SDIO WiFi cards will produce errors on the
SDIO bus. This is evident from the source code where you can see that
we try commands in a loop until we either get success or we've tried
too many times. The comment in the code reinforces this by saying
"just one write attempt may fail"
Unfortunately these failures sometimes end up causing an "-EILSEQ"
back to the core which triggers a retuning of the SDIO card and that
blocks all traffic to the card until it's done.
Let's disable retuning around the commands we expect might fail.
Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 29f6589140.
After that patch landed I find that my kernel log on
rk3288-veyron-minnie and rk3288-veyron-speedy is filled with:
brcmfmac: brcmf_sdio_bus_sleep: error while changing bus sleep state -110
This seems to happen every time the Broadcom WiFi transitions out of
sleep mode. Reverting the commit fixes the problem for me, so that's
what this patch does.
Note that, in general, the justification in the original commit seemed
a little weak. It looked like someone was testing on a SD card
controller that would sometimes die if there were CRC errors on the
bus. This used to happen back in early days of dw_mmc (the controller
on my boards), but we fixed it. Disabling a feature on all boards
just because one SD card controller is broken seems bad.
Fixes: 29f6589140 ("brcmfmac: disable command decode in sdio_aos")
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Double Lo <double.lo@cypress.com>
Cc: Madhan Mohan R <madhanmohan.r@cypress.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The function strcpy() is inherently not safe. Though the function
works without problems here, it would be better to use other safer
function, e.g. strlcpy(), to replace strcpy() still.
Signed-off-by: Neo Jou <neojou@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CONFIG_BRCMDBG selects WANT_DEV_COREDUMP but is only used by
brcmfmac so reflect that in the Kconfig.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The number of Kconfig items related to brcmfmac is considerable and
upcoming changes will add some more so it seems good idea to have
a separate Kconfig file for brcmfmac.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With ISC license text in place under the LICENSES folder switch
to using the SPDX license identifier to refer to the ISC license.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With ISC license text in place under the LICENSES folder switch
to using the SPDX license identifier to refer to the ISC license.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With ISC license text in place under the LICENSES folder switch
to using the SPDX license identifier to refer to the ISC license.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With ISC license text in place under the LICENSES folder switch
to using the SPDX license identifier to refer to the ISC license.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Normally firmware messages are printed with debugging enabled only. It's
a good idea as firmware may print a lot of messages that normal users
don't need to care about.
However, on firmware crash, it may be very helpful to log all recent
messages. There is almost always a backtrace available as well as rought
info on the latest actions/state.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some PCIE firmwares drop txstatus if pktid is 0 and make packet held in
host side and never be released. If that packet type is 802.1x, the
pend_8021x_cnt value will be always greater than 0 and show "Timed out
waiting for no pending 802.1x packets" error message when sending key to
dongle every time.
To be compatible with all firmwares, host should set txflow request id
from 1 instead of from 0.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If "ret_len" is negative then it could lead to a NULL dereference.
The "ret_len" value comes from nl80211_vendor_cmd(), if it's negative
then we don't allocate the "dcmd_buf" buffer. Then we pass "ret_len" to
brcmf_fil_cmd_data_set() where it is cast to a very high u32 value.
Most of the functions in that call tree check whether the buffer we pass
is NULL but there are at least a couple places which don't such as
brcmf_dbg_hex_dump() and brcmf_msgbuf_query_dcmd(). We memcpy() to and
from the buffer so it would result in a NULL dereference.
The fix is to change the types so that "ret_len" can't be negative. (If
we memcpy() zero bytes to NULL, that's a no-op and doesn't cause an
issue).
Fixes: 1bacb0487d ("brcmfmac: replace cfg80211 testmode with vendor command")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For PCIE wireless device with core revision less than 14, device may miss
PCIE to System Backplane Interrupt via PCIEtoSBMailbox. So add sending
mail box interrupt twice as a hardware workaround.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit 99d94ef367. I accidentally
applied this broken (failed to compile) patch due to a bug in my patchwork
script.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For PCIE wireless device with core revision less than 14, device may miss
PCIE to System Backplane Interrupt via PCIEtoSBMailbox. So add sending
mail box interrupt twice as a hardware workaround.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ACEPC T8 and T11 mini PCs contain quite generic names in the sys_vendor
and product_name DMI strings, without this patch brcmfmac will try to load:
"brcmfmac43455-sdio.Default string-Default string.txt" as nvram file which
is way too generic.
The DMI strings on which we are matching are somewhat generic too, but
"To be filled by O.E.M." is less common then "Default string" and the
system-sku and bios-version strings are pretty unique. Beside the DMI
strings we also check the wifi-module chip-id and revision. I'm confident
that the combination of all this is unique.
Both the T8 and T11 use the same wifi-module, this commit adds DMI
quirks for both mini PCs pointing to brcmfmac43455-sdio.acepc-t8.txt .
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1690852
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently if the call to brcmf_sdiod_set_backplane_window fails then
error return path leaks mypkt. Fix this by returning by a new
error path labelled 'out' that calls brcmu_pkt_buf_free_skb to free
mypkt. Also remove redundant check on err before calling
brcmf_sdiod_skbuff_write.
Addresses-Coverity: ("Resource Leak")
Fixes: a7c3aa1509 ("brcmfmac: Remove brcmf_sdiod_addrprep()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SDIO based brcm43456 is currently misdetected as brcm43455 and the wrong
firmware name is used. Correct the detection and load the correct
firmware file. Chiprev for brcm43456 is "9".
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)
Notice that, in this case, variable reqsz is not necessary,
hence it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case kmemdup fails, the fix sets conn_info->req_ie_len and
conn_info->resp_ie_len to zero to avoid buffer overflows.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmf_usb_free_q is no longer called with pending=true thus this boolean
parameter is no longer needed.
Signed-off-by: Piotr Figiel <p.figiel@camlintechnologies.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It was observed that rarely during USB disconnect happening shortly after
connect (before full initialization completes) usb_hub_wq would wait
forever for the dev_init_lock to be unlocked. dev_init_lock would remain
locked though because of infinite wait during usb_kill_urb:
[ 2730.656472] kworker/0:2 D 0 260 2 0x00000000
[ 2730.660700] Workqueue: events request_firmware_work_func
[ 2730.664807] [<809dca20>] (__schedule) from [<809dd164>] (schedule+0x4c/0xac)
[ 2730.670587] [<809dd164>] (schedule) from [<8069af44>] (usb_kill_urb+0xdc/0x114)
[ 2730.676815] [<8069af44>] (usb_kill_urb) from [<7f258b50>] (brcmf_usb_free_q+0x34/0xa8 [brcmfmac])
[ 2730.684833] [<7f258b50>] (brcmf_usb_free_q [brcmfmac]) from [<7f2517d4>] (brcmf_detach+0xa0/0xb8 [brcmfmac])
[ 2730.693557] [<7f2517d4>] (brcmf_detach [brcmfmac]) from [<7f251a34>] (brcmf_attach+0xac/0x3d8 [brcmfmac])
[ 2730.702094] [<7f251a34>] (brcmf_attach [brcmfmac]) from [<7f2587ac>] (brcmf_usb_probe_phase2+0x468/0x4a0 [brcmfmac])
[ 2730.711601] [<7f2587ac>] (brcmf_usb_probe_phase2 [brcmfmac]) from [<7f252888>] (brcmf_fw_request_done+0x194/0x220 [brcmfmac])
[ 2730.721795] [<7f252888>] (brcmf_fw_request_done [brcmfmac]) from [<805748e4>] (request_firmware_work_func+0x4c/0x88)
[ 2730.731125] [<805748e4>] (request_firmware_work_func) from [<80141474>] (process_one_work+0x228/0x808)
[ 2730.739223] [<80141474>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564)
[ 2730.746105] [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c)
[ 2730.752227] [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20)
[ 2733.099695] kworker/0:3 D 0 1065 2 0x00000000
[ 2733.103926] Workqueue: usb_hub_wq hub_event
[ 2733.106914] [<809dca20>] (__schedule) from [<809dd164>] (schedule+0x4c/0xac)
[ 2733.112693] [<809dd164>] (schedule) from [<809e2a8c>] (schedule_timeout+0x214/0x3e4)
[ 2733.119621] [<809e2a8c>] (schedule_timeout) from [<809dde2c>] (wait_for_common+0xc4/0x1c0)
[ 2733.126810] [<809dde2c>] (wait_for_common) from [<7f258d00>] (brcmf_usb_disconnect+0x1c/0x4c [brcmfmac])
[ 2733.135206] [<7f258d00>] (brcmf_usb_disconnect [brcmfmac]) from [<8069e0c8>] (usb_unbind_interface+0x5c/0x1e4)
[ 2733.143943] [<8069e0c8>] (usb_unbind_interface) from [<8056d3e8>] (device_release_driver_internal+0x164/0x1fc)
[ 2733.152769] [<8056d3e8>] (device_release_driver_internal) from [<8056c078>] (bus_remove_device+0xd0/0xfc)
[ 2733.161138] [<8056c078>] (bus_remove_device) from [<8056977c>] (device_del+0x11c/0x310)
[ 2733.167939] [<8056977c>] (device_del) from [<8069cba8>] (usb_disable_device+0xa0/0x1cc)
[ 2733.174743] [<8069cba8>] (usb_disable_device) from [<8069507c>] (usb_disconnect+0x74/0x1dc)
[ 2733.181823] [<8069507c>] (usb_disconnect) from [<80695e88>] (hub_event+0x478/0xf88)
[ 2733.188278] [<80695e88>] (hub_event) from [<80141474>] (process_one_work+0x228/0x808)
[ 2733.194905] [<80141474>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564)
[ 2733.201724] [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c)
[ 2733.207913] [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20)
It was traced down to a case where usb_kill_urb would be called on an URB
structure containing more or less random data, including large number in
its use_count. During the debugging it appeared that in brcmf_usb_free_q()
the traversal over URBs' lists is not synchronized with operations on those
lists in brcmf_usb_rx_complete() leading to handling
brcmf_usbdev_info structure (holding lists' head) as lists' element and in
result causing above problem.
Fix it by walking through all URBs during brcmf_cancel_all_urbs using the
arrays of requests instead of linked lists.
Signed-off-by: Piotr Figiel <p.figiel@camlintechnologies.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmu_pkt_buf_free_skb emits WARNING when attempting to free a sk_buff
which is part of any queue. After USB disconnect this may have happened
when brcmf_fws_hanger_cleanup() is called as per-interface psq was never
cleaned when removing the interface.
Change brcmf_fws_macdesc_cleanup() in a way that it removes the
corresponding packets from hanger table (to avoid double-free when
brcmf_fws_hanger_cleanup() is called) and add a call to clean-up the
interface specific packet queue.
Below is a WARNING during USB disconnect with Raspberry Pi WiFi dongle
running in AP mode. This was reproducible when the interface was
transmitting during the disconnect and is fixed with this commit.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1171 at drivers/net/wireless/broadcom/brcm80211/brcmutil/utils.c:49 brcmu_pkt_buf_free_skb+0x3c/0x40
Modules linked in: nf_log_ipv4 nf_log_common xt_LOG xt_limit iptable_mangle xt_connmark xt_tcpudp xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 iptable_filter ip_tables x_tables usb_f_mass_storage usb_f_rndis u_ether cdc_acm smsc95xx usbnet ci_hdrc_imx ci_hdrc ulpi usbmisc_imx 8250_exar 8250_pci 8250 8250_base libcomposite configfs udc_core
CPU: 0 PID: 1171 Comm: kworker/0:0 Not tainted 4.19.23-00075-gde33ed8 #99
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Workqueue: usb_hub_wq hub_event
[<8010ff84>] (unwind_backtrace) from [<8010bb64>] (show_stack+0x10/0x14)
[<8010bb64>] (show_stack) from [<80840278>] (dump_stack+0x88/0x9c)
[<80840278>] (dump_stack) from [<8011f5ec>] (__warn+0xfc/0x114)
[<8011f5ec>] (__warn) from [<8011f71c>] (warn_slowpath_null+0x40/0x48)
[<8011f71c>] (warn_slowpath_null) from [<805a476c>] (brcmu_pkt_buf_free_skb+0x3c/0x40)
[<805a476c>] (brcmu_pkt_buf_free_skb) from [<805bb6c4>] (brcmf_fws_cleanup+0x1e4/0x22c)
[<805bb6c4>] (brcmf_fws_cleanup) from [<805bc854>] (brcmf_fws_del_interface+0x58/0x68)
[<805bc854>] (brcmf_fws_del_interface) from [<805b66ac>] (brcmf_remove_interface+0x40/0x150)
[<805b66ac>] (brcmf_remove_interface) from [<805b6870>] (brcmf_detach+0x6c/0xb0)
[<805b6870>] (brcmf_detach) from [<805bdbb8>] (brcmf_usb_disconnect+0x30/0x4c)
[<805bdbb8>] (brcmf_usb_disconnect) from [<805e5d64>] (usb_unbind_interface+0x5c/0x1e0)
[<805e5d64>] (usb_unbind_interface) from [<804aab10>] (device_release_driver_internal+0x154/0x1ec)
[<804aab10>] (device_release_driver_internal) from [<804a97f4>] (bus_remove_device+0xcc/0xf8)
[<804a97f4>] (bus_remove_device) from [<804a6fc0>] (device_del+0x118/0x308)
[<804a6fc0>] (device_del) from [<805e488c>] (usb_disable_device+0xa0/0x1c8)
[<805e488c>] (usb_disable_device) from [<805dcf98>] (usb_disconnect+0x70/0x1d8)
[<805dcf98>] (usb_disconnect) from [<805ddd84>] (hub_event+0x464/0xf50)
[<805ddd84>] (hub_event) from [<80135a70>] (process_one_work+0x138/0x3f8)
[<80135a70>] (process_one_work) from [<80135d5c>] (worker_thread+0x2c/0x554)
[<80135d5c>] (worker_thread) from [<8013b1a0>] (kthread+0x124/0x154)
[<8013b1a0>] (kthread) from [<801010e8>] (ret_from_fork+0x14/0x2c)
Exception stack(0xecf8dfb0 to 0xecf8dff8)
dfa0: 00000000 00000000 00000000 00000000
dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
dfe0: 00000000 00000000 00000000 00000000 00000013 00000000
---[ end trace 38d234018e9e2a90 ]---
------------[ cut here ]------------
Signed-off-by: Piotr Figiel <p.figiel@camlintechnologies.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This includes bus reset & reloading a firmware. It should be sufficient
for a user space to (setup and) use a wireless device again.
Support for reset on USB & SDIO can be added later.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This improves handling PCIe firmware halts by printing a clear error
message and replaces a similar code in the SDIO bus support.
It will also allow further improvements like trying to recover from a
firmware crash.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During a normal brcmfmac lifetime brcmf_fw_alloc_request() is called
once only during the probe. It's safe to assume provided array is clear.
Further brcmfmac improvements may require calling it multiple times
though. This patch allows it by fixing invalid firmware paths like:
brcm/brcmfmac4366c-pcie.binbrcm/brcmfmac4366c-pcie.bin
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware may report general errors using a special message type. Add
basic support for it by simply decoding & printing an error number.
A sample situation in which firmware reports a buf error:
CONSOLE: 027084.733 no host response IOCTL buffer available..so fail the request
will now produce a "Firmware reported general error: 9" on the host.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This updates host struct to match the in-firmawre definition. It's a
cosmetic change as it only applies to the reserved struct space.
Fixes: c988b78244 ("brcmfmac: print firmware reported ring status errors")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
While experimenting with firmware loading I ended up in a state of
firmware reporting shared RAM address 0x04000001. It was causing:
[ 94.448015] Unable to handle kernel paging request at virtual address cd680001
due to reading out of the mapped memory.
This patch adds some basic validation to avoid kernel crashes due to the
unexpected firmware behavior.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This recently added macro provides more meaningful error messages thanks
to identifying a specific wiphy. It's especially important on systems
with few cards supported by the same (brcmfmac) driver.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c: In function 'brcmf_usb_state_change':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c:578:6: warning:
variable 'old_state' set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This macro will be used in more places not just the cfg80211.c. It makes
sense to pass some common struct to it as "struct wiphy" is mostly
referenced in cfg80211 code only.
A very common one (used above the bus abstraction layer) is struct
brcmf_pub. Many functions already keep reference to it which will make
using bphy_err() simpler. It should also allow extending that macro's
logic if it's ever needed.
This improves code recently added in the commit 3ef005b82e ("brcmfmac:
add bphy_err() and use it in the cfg80211.c").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far 160 MHz channels were treated as 20 MHz ones which was breaking
support for 40/80 MHz due to the brcmf_construct_chaninfo() logic and
its assumptions.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
1) Use switch to simplify/improve the code & avoid some duplication
2) Add warning for unsupported values
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware is capable of reporting ring status. It's used e.g. to signal
some problem with a specific ring setup. This patch adds support for
printing ring & error number which may be useful for debugging setup
issues.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The local variable chipname is string representation of chip id and revision
which is printed in the good flow of brcmf_fw_alloc_request(). Also use it
for the error path, ie. for unknown/unsupported devices.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the firmware crashes during the probe sequence we provide little
information on what really failed. This patch checks the sdpcm shared
location and show the trap information if a firmware trap has happened.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The MBSS feature was already disabled for bcm43362 as it resulted in a
beacon with BRCM_TEST_SSID regardless user configuration in hostapd. Now
the same has been reported for bcm4330 so disable the feature for this
device as well.
Reported-by: Russell King <linux@armlinux.org.uk>
Tested-by: Christopher Martin <chrsmrtn@gmail.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since we moved the drivers debugfs directory under ieee80211 debugfs the
debugfs entries need to be added after wiphy_register() has been called.
For most part that has been done accordingly, but for the debugfs entries
added by SDIO it was not and failed silently. This patch fixes that by
adding a bus-layer callback for it.
Fixes: 856d5a011c ("brcmfmac: allocate struct brcmf_pub instance using wiphy_new()")
Reported-by: Russel King <linux@armlinux.org.uk>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For USB there is no separate channel being used to pass events
from firmware to the host driver and as such are passed over the
data path. In order to detect mock event messages an additional
check is needed on event subtype. This check is added conditionally
using unlikely() keyword.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SSID length as received from firmware should not exceed
IEEE80211_MAX_SSID_LEN as that would result in heap overflow.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far there were two monitor frame formats:
1) 802.11 frames (with frame (sub)type & all addresses)
2) 802.11 frames with the radiotap header
Testing the latest FullMAC firmwares for 4366b1/4366c0 resulted in
discovering a new format being used. It seems (almost?) identical to the
one known from ucode used in SoftMAC devices which is most likely the
same codebase anyway.
While new firmwares will /announce/ radiotap header support using the
"rtap" fw capability string it seems no string was added for the new
ucode header format.
All above means that:
1) We need new format support when dealing with a received frame
2) A new feature bit & mapping quirks have to be added manually
As for now only an empty radiotap is being created. Adding support for
extracting some info (band, channel, signal, etc.) is planned for the
future.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix spelling mistakes in brcmfmac: "lenght" -> "length".
The typos are also in the special comment blocks which
translates to documentation.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This new macro uses wiphy_err() which:
1) Should be the best choice with wiphy already created
2) Uses dev_err() which allows identifying error-affected device
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This enables dev_err() usage (instead of pr_err()) in the __brcmf_err().
It makes error messages more meaningful and is important for debugging
errors/bugs on systems with multiple brcmfmac supported devices.
All bus files should follow & get updated similarly (soon).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far __brcmf_err() was using pr_err() which didn't allow identifying
device that was affected by an error. It's crucial for systems with more
than 1 device supported by brcmfmac (a common case for home routers).
This change allows passing struct brcmf_bus to the __brcmf_err(). That
struct has been agreed to be the most common one. It allows accessing
struct device easily & using dev_err() printing helper.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.1. Lots of new features in various drivers
but nothing really special standing out.
Major changes:
brcmfmac
* DMI nvram filename quirk for PoV TAB-P1006W-232 tablet
rsi
* support for hardware scan offload
iwlwifi
* support for Target Wakeup Time (TWT) -- a feature that allows the AP
to specify when individual stations can access the medium
* support for mac80211 AMSDU handling
* some new PCI IDs
* relicense the pcie submodule to dual GPL/BSD
* reworked the TOF/CSI (channel estimation matrix) implementation
* Some product name updates in the human-readable strings
mt76
* energy detect regulatory compliance fixes
* preparation for MT7603 support
* channel switch announcement support
mwifiex
* support for sd8977 chipset
qtnfmac
* support for 4addr mode
* convert to SPDX license identifiers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcWoRZAAoJEG4XJFUm622bOm4H/j2Tt6qS5yz3ioH2I7R+f7e/
8C2JJia+uQs8iChdyCjCFcDymmjB2l5u72JvupwCdERzp3okv/xmJiLW5wFW2z4x
B3Nrd4FV2EMIdsRXg1RWbwZHC4wIY6lFhL1OcUcuNwpb5ab1ppvQFHmH5logd7DC
euFSe02g8xmXdUMciRDKGUdiSiDIApmx9dUfguaqYtepqeW3hmDEEkeDicaf2fjq
cM5qAvssIAgUTqwIImEQQEU7j7A2TgMYkRBNzwv2QG47jy6OlgXkZVByvtq59irg
v4BFNtG6uRWTugxQ/FwYWeqsrnjegFNKm5MFbS6BDxbe05M7QzeK8zm55fE9ZGk=
=cHbd
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-02-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.1
First set of patches for 5.1. Lots of new features in various drivers
but nothing really special standing out.
Major changes:
brcmfmac
* DMI nvram filename quirk for PoV TAB-P1006W-232 tablet
rsi
* support for hardware scan offload
iwlwifi
* support for Target Wakeup Time (TWT) -- a feature that allows the AP
to specify when individual stations can access the medium
* support for mac80211 AMSDU handling
* some new PCI IDs
* relicense the pcie submodule to dual GPL/BSD
* reworked the TOF/CSI (channel estimation matrix) implementation
* Some product name updates in the human-readable strings
mt76
* energy detect regulatory compliance fixes
* preparation for MT7603 support
* channel switch announcement support
mwifiex
* support for sd8977 chipset
qtnfmac
* support for 4addr mode
* convert to SPDX license identifiers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the Kbuild core manipulates header search paths in a crazy
way [1].
To fix this mess, I want all Makefiles to add explicit $(srctree)/ to
the search paths in the srctree. Some Makefiles are already written in
that way, but not all. The goal of this work is to make the notation
consistent, and finally get rid of the gross hacks.
Having whitespaces after -I does not matter since commit 48f6e3cf5b
("kbuild: do not drop -I without parameter").
I also removed one header search path in:
drivers/net/wireless/broadcom/brcm80211/brcmutil/Makefile
I was able to compile without it.
[1]: https://patchwork.kernel.org/patch/9632347/
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: brcm80211-dev-list@cypress.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arend van Spriel
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The linux-firmware brcmfmac firmware files contain an embedded table with
per country allowed channels and strength info.
For recent hardware these versions of the firmware are specially build for
linux-firmware, the firmware files directly available from Cypress rely on
a separate clm_blob file for this info.
For some unknown reason Cypress refuses to provide the standard firmware
files + clm_blob files it uses elsewhere for inclusion into linux-firmware,
instead relying on these special builds with the clm_blob info embedded.
This means that the linux-firmware firmware versions often lag behind,
but I digress.
The brcmfmac driver does support the separate clm_blob file and always
tries to load this. Currently we use request_firmware for this. This means
that on any standard install, using the standard combo of linux-kernel +
linux-firmware, we will get a warning:
"Direct firmware load for ... failed with error -2"
On top of this, brcmfmac itself prints: "no clm_blob available (err=-2),
device may have limited channels available".
This commit switches to firmware_request_nowarn, fixing almost any brcmfmac
device logging the warning (it leaves the brcmfmac info message in place).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a system warning message, warn_slowpath-fmt, during suspend
while using supplicant join AP and enable wowl feature by IW command.
It's caused by brcmf_pno_remove_request path can't find the reqid.
This fix will not go to remove pno request function if there is no
pno scan.
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Lo-Hsiang Lo <double.lo@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_register() may fail, so let's check its status and issue an error
message if it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The Point of View TAB-P1006W-232 tablet contains quite generic names in
the sys_vendor and product_name DMI strings, without this patch brcmfmac
will try to load: brcmfmac43340-sdio.Insyde-BayTrail.txt as nvram file
which is a bit too generic.
Add a DMI quirk so that a unique and clearly identifiable nvram file
name is used on the PoV TAB-P1006W-232 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1202:5: warning: variable 'phybw40' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4625:5: warning: variable 'phybw40' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4834:5: warning: variable 'phybw40' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3085:17: warning: variable 'maxtargetpwr' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4215:17: warning: variable 'maxtargetpwr' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Since commit 1204aa17f3 ("brcmfmac: set WIPHY_FLAG_HAVE_AP_SME flag")
the Raspberry Pi 3 A+ (BCM43455) isn't able to operate in AP mode with
hostapd (device_ap_sme=1 use_monitor=0):
brcmfmac: brcmf_cfg80211_stop_ap: setting AP mode failed -52
So add the missing mgmt_stypes for AP mode to fix this.
Fixes: 1204aa17f3 ("brcmfmac: set WIPHY_FLAG_HAVE_AP_SME flag")
Suggested-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the update_connect_param callback is set, nl80211 expects the flag
WIPHY_FLAG_SUPPORTS_FW_ROAM to be set as well. However, this flag is
only set when modparam roamoff=0, while the callback is set
unconditionally. Since commit 7f9a3e150e this causes a warning in
wiphy_register, which breaks brcmfmac.
Disable the update_connect_param callback when roamoff=0 to fix this.
Fixes: 7f9a3e150e ("nl80211: Update ERP info using NL80211_CMD_UPDATE_CONNECT_PARAMS")
Cc: Stable <stable@vger.kernel.org> # 4.19+
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When CONFIG_NO_AUTO_INLINE is set, we get a false-postive warning
for the brcmf_fw_request_nvram_done() function, after gcc figures
out that brcmf_fw_nvram_from_efi() might not set the 'data_len'
variable, but fails to notice that it always returns NULL:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c: In function 'brcmf_fw_request_nvram_done':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c:560:11: error: 'data_len' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Mark it 'inline' to force gcc to understand this.
Fixes: ce2e6db554 ("brcmfmac: Add support for getting nvram contents from EFI variables")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AOS is a part of the SDIOD core that becomes active when the rest of
SDIOD is sleeping to keep SDIO bus alive responding to reduced set of
commands.
Transaction between AOS and SDIOD is not protected, and if cmd 52 is
received in AOS and in the middle of response state changed from AOS to
SDIOD, response is corrupted and it causes to SDIO Host controller to
hang.
Command decode for below chips are disabled in this commit:
- 4339
- 4345
- 4354
- 4373
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Double Lo <double.lo@cypress.com>
Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use chipcommon sr_control0 register to check 4373 sr support.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The number of words that the read FIFO has to contain except
the end of frame before sends data back to the host.
Max watermark = (512B - 2* (BurstLength))/4 =
(512 - 128)/4 = 384/4 = 0x60
so if burst length (i.e. BurstLength = 64) is increased,
watermark has to be reduced. This is the optimal setting for this chip.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Naveen Gupta <naveen.gupta@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
GCI core is needed for ULP operation. Allow GCI core enumuration with
below changes:
- Allow GCI to be added to core list even when it doesn't have a wrapper.
- Allow 8K address space size.
- Don't overwrite the address value when an additional size descriptor
is in place.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CYW43012 is a 1x1 802.11a/b/g/n Dual-Band HT20, 256-QAM/Turbo QAM. It
is an Ultra Low Power WLAN+BT combo chip.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Praveen Babu C <praveen.chandran@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Along with F2 watermark (existing) configuration, F1 MesBusyCtrl
should be enabled & sdio device RX FIFO watermark should be
configured to avoid overflow errors.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We got SDIO_CRC_ERROR with 4373 on SDR104 when doing bi-directional
throughput test. Enable watermark to 256 to guarantee the operation
stability.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the raw 4354 PCIe device ID for unprogrammed Cypress boards.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Winnie Chang <winnie.chang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware inform the driver about tx status by normal tx status signal
or compressed tx status signal. This patch adds support to handle the
compressed tx status signal.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The frameburst feature can enable per-packet framebursting in firmware
side and get higher TX throughput in High Throughput(HT) mode. To enhance
TX throughput, we enable frameburst mode in default firmware setting.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The credit numbers are static and tunable per chip in firmware side.
However the credit number may be changed that is based on packet pool
length and will send BRCMF_E_FIFO_CREDIT_MAP event to notify host driver
updates the credit numbers during interface up.
The purpose of this patch is making host driver has ability of updating
the credit numbers when receiving the BRCMF_E_FIFO_CREDIT_MAP event.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcATmGAAoJEG4XJFUm622bk9kH/1RWa2z7Gmjr2wBSLHryvRAH
3FAUSJ4GJPH6MJ5X824srkcVsx2Y1RVt2i+bLXRXLq35aZkrFswohTXVM2h5dU7T
Uy2SL+q9pBUcS7fyv9bE7XV7KsFBJly/5p/wciVRZMnEK6X/w6KkBx/vGvlm5I/C
q196KazbVAYcl6s7KMrfFOYt0Wsto/gdEeesSVBkmcCTEkiKUjjJ4WEDVvAKK+qB
AiwgSdioqYmmEiUuredm6bhVqZG3K2mScoCy95N3jXkiDaKkaYgVtBuAU4Cdju/t
WgLIc9EnUYxXZtwnt889X62P1OkDOtKlj/mjdsGyF0Vrs1W+kErDO0NocOvu2Tk=
=9bL7
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-11-30' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
I ended up tracking down some rather nasty issues with f2fs (and other
filesystem modules) constantly crashing on my kernel down to a
combination of out of bounds memory accesses, one of which was coming
from brcmfmac during module load:
[ 30.891382] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[ 30.894437] ==================================================================
[ 30.901581] BUG: KASAN: global-out-of-bounds in brcmf_fw_alloc_request+0x42c/0x480 [brcmfmac]
[ 30.909935] Read of size 1 at addr ffff2000024865df by task kworker/6:2/387
[ 30.916805]
[ 30.918261] CPU: 6 PID: 387 Comm: kworker/6:2 Tainted: G O 4.20.0-rc3Lyude-Test+ #19
[ 30.927251] Hardware name: amlogic khadas-vim2/khadas-vim2, BIOS 2018.07-rc2-armbian 09/11/2018
[ 30.935964] Workqueue: events brcmf_driver_register [brcmfmac]
[ 30.941641] Call trace:
[ 30.944058] dump_backtrace+0x0/0x3e8
[ 30.947676] show_stack+0x14/0x20
[ 30.950968] dump_stack+0x130/0x1c4
[ 30.954406] print_address_description+0x60/0x25c
[ 30.959066] kasan_report+0x1b4/0x368
[ 30.962683] __asan_report_load1_noabort+0x18/0x20
[ 30.967547] brcmf_fw_alloc_request+0x42c/0x480 [brcmfmac]
[ 30.967639] brcmf_sdio_probe+0x163c/0x2050 [brcmfmac]
[ 30.978035] brcmf_ops_sdio_probe+0x598/0xa08 [brcmfmac]
[ 30.983254] sdio_bus_probe+0x190/0x398
[ 30.983270] really_probe+0x2a0/0xa70
[ 30.983296] driver_probe_device+0x1b4/0x2d8
[ 30.994901] __driver_attach+0x200/0x280
[ 30.994914] bus_for_each_dev+0x10c/0x1a8
[ 30.994925] driver_attach+0x38/0x50
[ 30.994935] bus_add_driver+0x330/0x608
[ 30.994953] driver_register+0x140/0x388
[ 31.013965] sdio_register_driver+0x74/0xa0
[ 31.014076] brcmf_sdio_register+0x14/0x60 [brcmfmac]
[ 31.023177] brcmf_driver_register+0xc/0x18 [brcmfmac]
[ 31.023209] process_one_work+0x654/0x1080
[ 31.032266] worker_thread+0x4f0/0x1308
[ 31.032286] kthread+0x2a8/0x320
[ 31.039254] ret_from_fork+0x10/0x1c
[ 31.039269]
[ 31.044226] The buggy address belongs to the variable:
[ 31.044351] brcmf_firmware_path+0x11f/0xfffffffffffd3b40 [brcmfmac]
[ 31.055601]
[ 31.057031] Memory state around the buggy address:
[ 31.061800] ffff200002486480: 04 fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00
[ 31.068983] ffff200002486500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 31.068993] >ffff200002486580: 00 00 00 00 00 00 00 00 fa fa fa fa 00 00 00 00
[ 31.068999] ^
[ 31.069017] ffff200002486600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 31.096521] ffff200002486680: 00 00 00 00 00 00 00 00 00 00 00 00 fa fa fa fa
[ 31.096528] ==================================================================
[ 31.096533] Disabling lock debugging due to kernel taint
It appears that when trying to determine the length of the string in the
alternate firmware path, we make the mistake of not handling the case
where the firmware path is empty correctly. Since strlen(mp_path) can
return 0, we'll end up accessing mp_path[-1] when the firmware_path
isn't provided through the module arguments.
So, fix this by just setting the end char to '\0' by default, and only
changing it if we have a non-zero length. Additionally, use strnlen()
with BRCMF_FW_ALTPATH_LEN instead of strlen() just to be extra safe.
Fixes: 2baa3aaee2 ("brcmfmac: introduce brcmf_fw_alloc_request() function")
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Arend Van Spriel <arend.vanspriel@broadcom.com>
Cc: Himanshu Jha <himanshujha199640@gmail.com>
Cc: Dan Haab <dhaab@luxul.com>
Cc: Jia-Shyr Chuang <saint.chuang@cypress.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ARM systems with UEFI may have both devicetree (of) and DMI data in this
case we end up setting brcmf_mp_device.board_type twice.
In this case we should prefer the devicetree data, because:
1) The devicerree data is more reliable
2) Some ARM systems (e.g. the Raspberry Pi 3 models) support both UEFI and
classic uboot booting, the devicetree data is always there, so using it
makes sure we ask for the same nvram file independent of how we booted.
This commit moves the brcmf_dmi_probe call to before the brcmf_of_probe
call, so that the latter can override the value of the first if both are
set.
Fixes: bd1e82bb42 ("brcmfmac: Set board_type from DMI on x86 based ...")
Cc: Peter Robinson <pbrobinson@gmail.com>
Tested-and-reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The newest firmwares provide STA info using v7 of the struct. As v7
isn't backward compatible, a union is needed.
Even though brcmfmac does not use any of the new info it's important to
provide the proper struct buffer. Without this change new firmwares will
fallback to the very limited v3 instead of something in between such as
v4.
Signed-off-by: Dan Haab <dan.haab@luxul.com>
Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current driver includes macro that is available from general cordic
library. Use that and drop unused duplicate and unneeded internal
definitions.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver can report IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ so it's
important to provide valid & complete info about supported bands for
each channel. By default no support for 160 MHz should be assumed unless
firmware reports it for a given channel later.
This fixes info passed to the userspace. Without that change userspace
could try to use invalid channel and fail to start an interface.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of direct SKB list pointer accesses.
The loops in this function had to be rewritten to accommodate this
more easily.
The first loop iterates now over the target list in the outer loop,
and triggers an mmc data operation when the per-operation limits are
hit.
Then after the loops, if we have any residue, we trigger the last
and final operation.
For the page aligned workaround, where we have to copy the read data
back into the original list of SKBs, we use a two-tiered loop. The
outer loop stays the same and iterates over pktlist, and then we have
an inner loop which uses skb_peek_next(). The break logic has been
simplified because we know that the aggregate length of the SKBs in
the source and destination lists are the same.
This change also ends up fixing a bug, having to do with the
maintainance of the seg_sz variable and how it drove the outermost
loop. It begins as:
seg_sz = target_list->qlen;
ie. the number of packets in the target_list queue. The loop
structure was then:
while (seq_sz) {
...
while (not at end of target_list) {
...
sg_cnt++
...
}
...
seg_sz -= sg_cnt;
The assumption built into that last statement is that sg_cnt counts
how many packets from target_list have been fully processed by the
inner loop. But this not true.
If we hit one of the limits, such as the max segment size or the max
request size, we will break and copy a partial packet then contine
back up to the top of the outermost loop.
With the new loops we don't have this problem as we don't guard the
loop exit with a packet count, but instead use the progression of the
pkt_next SKB through the list to the end. The general structure is:
sg_cnt = 0;
skb_queue_walk(target_list, pkt_next) {
pkt_offset = 0;
...
sg_cnt++;
...
while (pkt_offset < pkt_next->len) {
pkt_offset += sg_data_size;
if (queued up max per request)
mmc_submit_one();
}
}
if (sg_cnt)
mmc_submit_one();
The variables that maintain where we are in the MMC command state such
as req_sz, sg_cnt, and sgl are reset when we emit one of these full
sized requests.
Signed-off-by: David S. Miller <davem@davemloft.net>
On one of my devices I got WARNINGs when brcmfmac tried to decode
chanspec. I couldn't tell if it was some unsupported format or just a
malformed value passed by a firmware.
Print chanspec value so it's possible to debug a possible problem.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This message greatly spams the log under heavy Tx of frames with BK access
class which is especially true when operating as AP. It is also not informative
as the "agg'ablity" of TIDs are set once and never change.
Fix this by logging only in debug mode.
Signed-off-by: Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in brcmf_err error message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In some cases the EFI-var stored nvram contains "ccode=ALL" or "ccode=XV"
to specify "worldwide" compatible settings, but these 2 ccode-s do not work
properly.
I've tested the different known "worldwide" ccode-s used in various nvram
sources with the latest firmwares from linux-firmware for various brcmfmac
models, here is a simplified (*) table with what each setting results in:
ALL: 12-14 disab, U-NII-1, U-NII-2 no-IR/radar, U-NII-3
XV: 12-14 no-IR, disables all 5G channels
XY: 12-13 enab, 14 disab, U-NII-1 enab, U-NII-2 no-IR/radar, U-NII-3 disab
X2: 12-13 no-IR, 14 dis, U-NII-1 no-IR, U-NII-2 no-IR/radar, U-NII-3 no-IR
Where 12,13,14 are 2.4G channels 12-14 and U-NII-1/2/3 are the 3 different
5G channel groups. no-IR is no-Initiate-Radiation, we will never send on
these channels without first having received valid wifi traffic there.
This immediately shows that both ALL and XV are not as worldwide as we want
them to be. ALL causes channels 12 and 13 to not be available and XV causes
all 5GHz channels to not be available. Also ALL unconditionally enables the
U-NII-1 and U-NII-3 5G groups, while we really should be using no-IR for
these.
This commit replace XV and ALL with X2, which allows usage of chan 12-13
and 5G channels, but only after receiving valid wifi traffic there first.
Note that this configure the firmware's channel limits, the kernels own
regulatory restrictions based on e.g. regulatory info received from the
access-point, will be applied on top of this.
This fixes channels 12+13 not working on the Asus T200TA and the Lenovo
Mixx 2 8 and 5G channels not working on the Asus T100HA.
This has been tested on the following models: Acer Iconia Tab8 w1-810,
Acer One 10, Asus T100CHI, Asus T100HA, Asus T100TA, Asus T200TA and a
Lenovo Mixx 2 8.
*) There are some exceptions to this table:
1) On really old firmware e.g. linux-firmware's 2011 brcmfmac4330-sdio.bin
ALL really means all, unconditionally enabling everything
2) The exact meaning might be influenced by setting the regrev nvram var.
Specifically using ccode=XV + regrev=1 on brcmfmac43241b4 leads to:
12-14 no-ir, U-NII-1 no-ir, U-NII-2 no-ir/radar, U-NII-3 no-ir
But only on the brcmfmac43241b4 and not on e.g. the brcmfmac43340
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Various X86 laptops with a SDIO attached brcmfmac wifi chip, store the
nvram contents in a special EFI variable. This commit adds support for
getting nvram directly from this EFI variable, without the user needing
to manually copy it.
This makes Wifi / Bluetooth work out of the box on these devices instead of
requiring manual setup.
This has been tested on the following models: Acer Iconia Tab8 w1-810,
Acer One 10, Asus T100CHI, Asus T100HA, Asus T100TA, Asus T200TA and a
Lenovo Mixx 2 8.
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The "cur" variable is now only used for a debug print and we already
print the same info from brcmf_fw_complete_request(), so the debug print
does not provide any extra info and we can remove it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For x86 based machines, set the board_type used for nvram file selection
based on the DMI sys-vendor and product-name strings.
Since on some models these strings are too generic, this commit also adds
a quirk table overriding the strings for models listed in that table.
The board_type setting is used to load the board-specific nvram file with
a board-specific name so that we can ship files for each supported board
in linux-firmware.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For of/devicetree using machines, set the board_type used for nvram file
selection to the first string listed in the top-level's node compatible
string, aka the machine-compatible as used by of_machine_is_compatible().
The board_type setting is used to load the board-specific nvram file with
a board-specific name so that we can ship files for each supported board
in linux-firmware.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The nvram files which some brcmfmac chips need are board-specific. To be
able to distribute these as part of linux-firmware, so that devices with
such a wifi chip will work OOTB, multiple (one per board) versions must
co-exist under /lib/firmware.
This commit adds support for callers of the brcmfmac/firmware.c code to
pass in a board_type parameter through the request structure.
If that parameter is set then the code will first try to load
chipmodel.board_type.txt before falling back to the old chipmodel.txt name.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Before this commit brcmf_fw_request_done would call
brcmf_fw_request_next_item to load the next item, which on an error would
call brcmf_fw_request_done, which if the error is recoverable (*) will
then continue calling brcmf_fw_request_next_item for the next item again
which on an error will call brcmf_fw_request_done again...
This does not blow up because we only have a limited number of items so
we never recurse too deep. But the recursion is still quite ugly and
frankly is giving me a headache, so lets fix this.
This commit fixes this by removing brcmf_fw_request_next_item and by
making brcmf_fw_get_firmwares and brcmf_fw_request_done directly call
firmware_request_nowait resp. firmware_request themselves.
*) brcmf_fw_request_nvram_done fallback path succeeds or
BRCMF_FW_REQF_OPTIONAL is set
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmf_fw_request_next_item and brcmf_fw_request_done both have identical
code to complete the fw-request depending on the item-type.
This commit adds a new brcmf_fw_complete_request helper removing this code
duplication.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Previous commit /adding/ support for 160 MHz chanspecs was incomplete.
It didn't set bandwidth info and didn't extract control channel info. As
the result it was also using uninitialized "sb" var.
This change has been tested for two chanspecs found to be reported by
some devices/firmwares:
1) 60/160 (0xee32)
Before: chnum:50 control_ch_num:36
After: chnum:50 control_ch_num:60
2) 120/160 (0xed72)
Before: chnum:114 control_ch_num:100
After: chnum:114 control_ch_num:120
Fixes: 330994e8e8 ("brcmfmac: fix for proper support of 160MHz bandwidth")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Beacons are not updated to reflect TIM changes. This is not compliant with
power-saving client stations as the beacons do not have valid TIM and can
cause the network to stall at random occasions and to have highly variable
latencies.
Fix it by updating beacon templates on mac80211 set_tim callback.
Addresses an issue described in:
https://marc.info/?i=20180911163534.21312d08%20()%20manjaro
Signed-off-by: Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver sends an action frame down and waits for a completion signal
triggered by the received BRCMF_E_ACTION_FRAME_OFF_CHAN_COMPLETE event
to continue the process. However, the action frame could be transmitted
either on the current channel or on an off channel. For the on-channel
case, only BRCMF_E_ACTION_FRAME_COMPLETE event will be received when
the frame is transmitted, which make the driver always wait a full
timeout duration. This patch has the completion signal be triggered by
receiving the BRCMF_E_ACTION_FRAME_COMPLETE event for the on-channel
case.
This change fixes WFA p2p certification 5.1.19 failure.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Finding a common channel to send an action frame out is required for
some action types. Since a loop with several scan retry is used to find
the channel, a short wait time could be considered for each attempt.
This patch reduces the wait time from 1500 to 450 msec for each action
frame scan.
This patch fixes the WFA p2p certification 5.1.20 failure caused by the
long action frame send time.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of new features for 4.20. mt76 driver is going through major
refactoring and that's why there are so many mt76 patches. iwlwifi is
also under heavy development and smaller changes to other drivers.
Also wireless-drivers was merged to fix a conflict between the two trees.
Major changes:
ath10k
* limit available channels via DT ieee80211-freq-limit
wil6210
* add 802.11r Fast Roaming support for AP and station modes
* add support for channel 4
iwlwifi
* new FW API handling
* some improvements in the PCI recovery mechanism
* enable a new scanning feature;
* continued work on HE (mostly radiotap)
* TKIP implementation in new devices
* work continues for new 22560 hardware
mt76
* add support for Alfa AWUS036ACM
* lots of refactoring to make it easier to add new hardware support
* prepare for adding mt76x0e (pci-e variant) support
* add CONFIG_MT76x0E kconfig symbol
brcmfmac
* add support CYW89342 mini-PCIe device
* add 4-way handshake offload detection for FT-802.1X
* enable NL80211_EXT_FEATURE_CQM_RSSI_LIST
* fix for proper support of 160MHz bandwidth
rtl8xxxu
* add rtl8188ctv support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbs6LVAAoJEG4XJFUm622b0sAH/1WLU433ZipgULs6PLULDz3/
cFS4CSu9+Hewx9MKvdr+vgMoru70CkiFIZMJeo/oNqAtFb6TQhXPFz2Ci3K4Y6jK
yZKATh9PvzQrOGQ1iy4p8QK6bQ9WRUNY5+elJuNQH62oB/SZ0XqCMU8ujUQRSaTC
xVqfIRnAtKcchAm/nqxx+EwlGCiUmlyt2pw2IUXXABLW7Fkj3Z3ISlOd8xVW6tca
XyWlx9pjZOrFrgOzyORB/B4TNI5q5CdcYPg2DEpqOs6LQeGXEq4BSxfxCe2de4ku
St6417K0OFTbUTZS7kJaxJnQFd1ZWhDtj5cJUzdNsSVzqeYeJoTnR4FBqDWLlec=
=7Nmq
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-10-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.20
First set of new features for 4.20. mt76 driver is going through major
refactoring and that's why there are so many mt76 patches. iwlwifi is
also under heavy development and smaller changes to other drivers.
Also wireless-drivers was merged to fix a conflict between the two trees.
Major changes:
ath10k
* limit available channels via DT ieee80211-freq-limit
wil6210
* add 802.11r Fast Roaming support for AP and station modes
* add support for channel 4
iwlwifi
* new FW API handling
* some improvements in the PCI recovery mechanism
* enable a new scanning feature;
* continued work on HE (mostly radiotap)
* TKIP implementation in new devices
* work continues for new 22560 hardware
mt76
* add support for Alfa AWUS036ACM
* lots of refactoring to make it easier to add new hardware support
* prepare for adding mt76x0e (pci-e variant) support
* add CONFIG_MT76x0E kconfig symbol
brcmfmac
* add support CYW89342 mini-PCIe device
* add 4-way handshake offload detection for FT-802.1X
* enable NL80211_EXT_FEATURE_CQM_RSSI_LIST
* fix for proper support of 160MHz bandwidth
rtl8xxxu
* add rtl8188ctv support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ucode chunk might be relatively large and the allocation with
kmalloc() may fail occasionally. Since the data isn't DMA-transferred
but by manual loops, we can use vmalloc instead of kmalloc.
For a better performance, though, kvmalloc() would be the best choice
in such a case, so let's replace with it.
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1103431
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c: In function 'brcmf_sdio_rxglom':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:1466:11: warning:
variable 'sfdoff' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c: In function 'brcmf_sdio_bus_preinit':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:3408:7: warning:
variable 'pad_size' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
debugfs_remove_recursive has taken IS_ERR_OR_NULL into account. So just
remove the condition check before debugfs_remove_recursive.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When obtaining the firmware capability a buffer is provided of 512
bytes. However, if all features in firmware are supported the buffer
needs to be 565 bytes as otherwise truncated information is retrieved
from firmware. Increasing the buffer to 768 bytes on stack.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of direct SKB list pointer accesses.
In these situations, we absolutely know that the SKB queue in question
is non-empty.
Signed-off-by: David S. Miller <davem@davemloft.net>
strnchr takes arguments in the order of its name: string, max bytes to
read, character to search for. Here we're passing '\n' aka 10 as the
buffer size, and searching for sizeof(buf) aka BRCMF_DCMD_SMLEN aka
256 (aka '\0', since it's implicitly converted to char) within those 10
bytes.
Just interchanging the last two arguments would still leave a bug,
because if we've been successful once, there are not sizeof(buf)
characters left after the new value of p.
Since clmver is immediately afterwards passed as a %s argument, I assume
that it is actually a properly nul-terminated string. For that case, we
have strreplace().
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add 4-way handshake offload detection for FT with EAP authentication.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add WLAN_AKM_SUITE_FT_8021X and WLAN_AKM_SUITE_FT_PSK in
brcmf_set_key_mgmt() for FT support.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CYW89342 is a 2x2 MIMO, 802.11a/b/g/n/ac for WLAN. It is a member of
4355/4359 family.
Signed-off-by: Jia-Shyr Chuang <saint.chuang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove the unnecessary parentheses to fix the clang warning of
extraneous parentheses.
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The kernel BUG happens when wowl is enabled from firmware. In
brcmf_wiphy_wowl_params(), cfg is a NULL pointer because it is
drvr->config returned from wiphy_to_cfg(), and drvr->config is not set
yet. To fix it, set drvr->config before brcmf_setup_wiphy() which
calls brcmf_wiphy_wowl_params().
Fixes: 856d5a011c ("brcmfmac: allocate struct brcmf_pub instance using wiphy_new()")
Signed-off-by: Winnie Chang <winnie.chang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This time a bigger pull request as we have two new Mediatek drivers
MT76x2u (CONFIG_MT76x2U) and MT76x0U (CONFIG_MT76x0U). Also iwlwifi got
support for the new IEEE 802.11ax standard, the successor for
802.11ac. And naturally smaller new features and bugfixes all over.
Major changes:
wcn36xx
* fix WEP in client mode
wil6210
* add support for Talyn-MB (Talyn ver 2.0) device
* add support for enhanced DMA firmware feature
iwlwifi
* implement 802.11ax D2.0
* support for the new 22560 device family
* new PCI IDs for 22000 and 22560
qtnfmac
* implement cfg80211 power management callback
* enable multiple SSIDs scan support
* qtnfmac: implement basic WoWLAN support
mt7601u
* fall back to software encryption for hw unsupported ciphers
* enable 802.11 Management Frame Protection (MFP)
mt76
* support setting RTS threshold
* add USB support
* add support for MT76x2u devices
* add support for MT76x0U devices
mwifiex
* allow user space to set all other IEs except WMM IE
rsi
* add firmware support for AP+BT dual mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbZyxDAAoJEG4XJFUm622bq2AH/2yJAeOKb7Z25ezsvldaEDd3
cYS4TjLevXacDU5NdINtm1IRMct1ZldwUjrjgR2I/eLaSHhxyIdV4hb05etSN8qZ
yo86aa1gs+8rSEn/GVO8UjX8Bh4NM/tff+yzMKWiWJGe9DtBvswSUPxBOU91vS8K
WcCpvWh9SpmAPyZEDWsZnTK7AUc+X2T+Soit+pJmLm9P3RxkvMqQxG82eMGVnooO
5aNe0T9zYLB4aB8unCJqPSYSLVDJ55vnC8tFIjcEhNCF/745gyMD/CrcQ4zCxdN/
KF6WEDc/XePF5qrHvkzWA7HiR0Xs9pDt3KugkU0enZV+cba0kKaBq230sZ++1KM=
=BwxN
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-08-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.19
This time a bigger pull request as we have two new Mediatek drivers
MT76x2u (CONFIG_MT76x2U) and MT76x0U (CONFIG_MT76x0U). Also iwlwifi got
support for the new IEEE 802.11ax standard, the successor for
802.11ac. And naturally smaller new features and bugfixes all over.
Major changes:
wcn36xx
* fix WEP in client mode
wil6210
* add support for Talyn-MB (Talyn ver 2.0) device
* add support for enhanced DMA firmware feature
iwlwifi
* implement 802.11ax D2.0
* support for the new 22560 device family
* new PCI IDs for 22000 and 22560
qtnfmac
* implement cfg80211 power management callback
* enable multiple SSIDs scan support
* qtnfmac: implement basic WoWLAN support
mt7601u
* fall back to software encryption for hw unsupported ciphers
* enable 802.11 Management Frame Protection (MFP)
mt76
* support setting RTS threshold
* add USB support
* add support for MT76x2u devices
* add support for MT76x0U devices
mwifiex
* allow user space to set all other IEs except WMM IE
rsi
* add firmware support for AP+BT dual mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some features supported by firmware aren't advertised and there is no
way for a driver to query them. This includes e.g. monitor mode details.
Most firmwares support monitor interface but only the latest ones
/announce/ it with a "monitor" flag in the "cap" iovar. There isn't any
reliable detection method for older firmwares (BRCMF_C_MONITOR was tried
but "it only indicates the core part of the stack supports").
Similarly support for tagging monitor frames and building radiotap
headers can't be reliably detected for all firmwares.
This commit adds table that allows mapping features to firmware version.
It adds mappings for 43602a1 and 4366b1 firmwares from
linux-firmware.git. Both were confirmed to be passing monitor frames.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
NVRAM is designed to work with Broadcom's SDK Linux kernel which fakes
PCI domain 0 for all internal MMIO devices. Since official Linux kernel
uses platform devices for that purpose there is a mismatch in numbering
PCI domains.
There used to be a fix for that problem but it was accidentally dropped
during the last firmware loading rework. That resulted in brcmfmac not
being able to extract device specific NVRAM content and all kind of
calibration problems.
Reported-by: Aditya Xavier <adityaxavier@gmail.com>
Fixes: 2baa3aaee2 ("brcmfmac: introduce brcmf_fw_alloc_request() function")
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The first set of patches for 4.19. Only smaller features and bug
fixes, not really anything major. Also included are changes to
include/linux/bitfield.h, we agreed with Johannes that it makes sense
to apply them via wireless-drivers-next.
Major changes:
ath10k
* support channel 173
* fix spectral scan for QCA9984 and QCA9888 chipsets
ath6kl
* add support for Dell Wireless 1537
ti wlcore
* add support for runtime PM
* enable runtime PM autosuspend support
qtnfmac
* support changing MAC address
* enable source MAC address randomization support
libertas
* fix suspend and resume for SDIO cards
mt76
* add software DFS radar pattern detector for mt76x2 based devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbVgnkAAoJEG4XJFUm622b/DAH/0wmjFQrt1qe/goZ4igZOC5z
TTqPUmv7HO4PbHV6mU5yOFGsRCaGDo1cTyEeoiaYNGH6bQLzzJZeQORkuPQB2q5S
BCwlaET7F2iSmk8hx7eboONyVDm5v2+g6NMHBoikVFz1wZ13kCVa4sHkokUJKYB9
XNw3B2OiarPv9i37DlY3woMlY+6VMQh8J6GiB9cJSa4Xs+7l1aQCdQRP03SabI71
gLBEsW+bEVZrUdJGB5cZ8c6LmukmRQMDKMTQYUna5ZXeW1IX3ejYcQGHzzCZoKJS
LPUmisz4014r5aBzXIu3ctVn4LnVhMS5ms0EH1A6IX3vx8G9QynqH5lm9VQ1OXI=
=kWW/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-07-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.19
The first set of patches for 4.19. Only smaller features and bug
fixes, not really anything major. Also included are changes to
include/linux/bitfield.h, we agreed with Johannes that it makes sense
to apply them via wireless-drivers-next.
Major changes:
ath10k
* support channel 173
* fix spectral scan for QCA9984 and QCA9888 chipsets
ath6kl
* add support for Dell Wireless 1537
ti wlcore
* add support for runtime PM
* enable runtime PM autosuspend support
qtnfmac
* support changing MAC address
* enable source MAC address randomization support
libertas
* fix suspend and resume for SDIO cards
mt76
* add software DFS radar pattern detector for mt76x2 based devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
That struct is used when querying firmware for the STA. It seem is has
been changing during the time. Luckily its format seems to be backward
compatible starting with v2 (the only breakage was v1 -> v2).
The version that was supported by brcmfmac so far was v4. It was what
43602a1 and 4366b1 firmwares (7.35.177.56 and 10.10.69.3309 accordingly)
were using. It also seems to be used by early 4366c0 firmwares
(10.10.69.6908 and 10.10.69.69017).
The problem appears when switching to the 10.10.122.20 firmware. It uses
v5 and instead of falling back to v4 when submitted buffer isn't big
enough it fallbacks to the v3.
To receive all v4 specific info with the newest firmware we have to
submit a struct (buffer) that matches v5.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
That struct is passed by a firmware when querying for STA info. Flags
are used to indicate what info could be obtained.
These new defines may allow passing more info to the cfg80211 in the
future. They had been obtained from Broadcom's SDK file wlioctl_defs.h
used by DD-WRT.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New Broadcom firmwares mark monitor mode packets using a newly defined
bit in the flags field. Use it to filter them out and pass to the
monitor interface. These defines were found in bcmmsgbuf.h from SDK.
As not every firmware generates radiotap header this commit introduces
BRCMF_FEAT_MONITOR_FMT_RADIOTAP flag. It has to be has based on firmware
capabilities. If not present brcmf_netif_mon_rx() will assume packet is
a raw 802.11 frame and will prepend it with an empty radiotap header.
This new code is limited to the msgbuf protocol at this point. Adding
support for SDIO/USB devices will require some extra work (possibly a
new firmware release).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Depending on used build-time options some firmwares may already include
radiotap header in passed monitor frames. Add a new feature flag to
store info about it. It's needed for proper handling of received frames
before passing them up.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Many/most of firmwares support creating monitor interface but only the
most recent ones explicitly /announce/ it using a "monitor" entry in the
list of capabilities.
Check for that entry and store internally info about monitor mode
support using a new feature flag. Once we sort out all details of
handling monitor interface it will be used when reporting available
interfaces to the cfg80211.
Later some fallback detecion method may be added for older firmwares.
For now just stick to the "monitor" capability which should be 100%
reliable.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of fixes for 4.18 and for numerous drivers. Something to mention
about is the wcn36xx fix which makes it possible to compile with gcc older than
4.4 (though I'm not sure if we even support those anymore).
qtnfmac
* coverity fix for a new commit in v4.18-rc1
rtlwifi
* fix kernel oops during driver removal
* fix firmware image corruption for rtl8821ae
brcmfmac
* fix crash if there's no firmware image
mwifiex
* a revert and a better fix for a new commit v4.18-rc1
mt7601u
* fix a recent regression about unnecessary warning about avg_rssi
wcn36xx
* convert testmode.c to plain ASCII
ath10k
* fix a firmware crash during bandwidth change
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbO1LKAAoJEG4XJFUm622bPEgH/jJ552p5KdOFkwtKWQ9sybKP
53yCEJw0sjaKVaXdPbOLZQP4ioJ0xYiOxKN1LBmBg2AVFKvnSp5LRWwmpzqdpOoE
oYo09wcSE5Q7AFHaWDmV5/6ze/S1Aem9B5iNdS/hScuXqsnqct17RVO1zVWpHnU5
W8+qVFrBcbqrvuTDdGo5GBaUQBeRHpIpGjABBk7D6qXVwOtzr2ibKGRHRITu3yYo
vA+IF+S+IwWEITt4AxaN728sk6Q3S9r5kBmRlyzlfeSmT8S/zS8Hid5P2eQz6Dv4
Ib22ZvBVFyKQd4qeXYG1lWxbTQrNZIY3JUDGkcdhkhdb3TKYL37x3mWP2LoTpK4=
=0sGc
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-07-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.18
First set of fixes for 4.18 and for numerous drivers. Something to mention
about is the wcn36xx fix which makes it possible to compile with gcc older than
4.4 (though I'm not sure if we even support those anymore).
qtnfmac
* coverity fix for a new commit in v4.18-rc1
rtlwifi
* fix kernel oops during driver removal
* fix firmware image corruption for rtl8821ae
brcmfmac
* fix crash if there's no firmware image
mwifiex
* a revert and a better fix for a new commit v4.18-rc1
mt7601u
* fix a recent regression about unnecessary warning about avg_rssi
wcn36xx
* convert testmode.c to plain ASCII
ath10k
* fix a firmware crash during bandwidth change
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The BIT macro uses unsigned long which some architectures handle as 32 bit
and therefore might cause macro's shift to overflow when used on a value
equals or larger than 32 (NL80211_STA_INFO_RX_DURATION and afterwards).
Since 'filled' member in station_info changed to u64, BIT_ULL macro
should be used with all NL80211_STA_INFO_* attribute types instead of BIT
to prevent future possible bugs when one will use BIT macro for higher
attributes by mistake.
This commit cleans up all usages of BIT macro with the above field
in wireless-drivers by changing it to BIT_ULL instead. In addition, there are
some places which don't use BIT nor BIT_ULL macros so align those as well.
Signed-off-by: Omer Efrat <omer.efrat@tandemg.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function wlc_phy_workarounds_nphy_rev1 is local to the source and
does not need to be in global scope, so make it static.
Cleans up sparse warning:
symbol 'wlc_phy_workarounds_nphy_rev1' was not declared. Should it
be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The last value in the log_table wraps around to a negative value
since s16 has a value range of -32768 to 32767. This is not what
the table intends to represent. Use the closest positive value
32767.
This fixes a warning seen with clang:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_qmath.c:216:2: warning:
implicit conversion from 'int' to 's16' (aka 'short') changes
value from 32768
to -32768 [-Wconstant-conversion]
32768
^~~~~
1 warning generated.
Fixes: 4c0bfeaae9 ("brcmsmac: fix array out-of-bounds access in qm_log10")
Cc: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes the clang warning of extraneous parentheses, with the
following coccinelle script.
@@
identifier i;
expression e;
statement s;
@@
if (
-(i == e)
+i == e
)
s
Suggested-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hopefully the last pull request to 4.18 before the merge window.
Nothing major here, we have smaller new features and of course a lots
of fixes.
Major changes:
ath10k
* add memory dump support for QCA9888 and QCA99X0
* add support to configure channel dwell time
* support new DFS host confirmation feature in the firmware
ath
* update various regulatory mappings
wcn36xx
* various fixes to improve reliability
* add Factory Test Mode support
brmfmac
* add debugfs file for reading firmware capabilities
mwifiex
* support sysfs initiated device coredump
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbD/3rAAoJEG4XJFUm622b1ZwH/1xe1IqcwJXzfoDsYPlXVnSh
TiLExjKkD0ty5M0//844FxpxE1sSYJKOJ11uz/COzyG2qi4+5lgpUdjnDoINuKfH
ycqrXGssW7ogPWkVvnxKtlEYvkHNRYLQtxvd26umT77C69jVJLD0x9uihhh2En/C
EKs+OK1Pp0SRvTfB4AblWzoAnpEe1wHJFFh4i3F5H0lMGxLQz/YjFl5aeAjjR406
0vSKLGy2wKIydp8Pe4cAqBEeUWDJurn8ufkk7bmAET5zaXTH1qgZzLH3OWtx/ksz
mcPQq9/ctv35G2917t3Sn69SIUCDGfYkP5DiZV+ti0Hz2gIV0zOg7mGYCU8uHaU=
=11X5
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.18
Hopefully the last pull request to 4.18 before the merge window.
Nothing major here, we have smaller new features and of course a lots
of fixes.
Major changes:
ath10k
* add memory dump support for QCA9888 and QCA99X0
* add support to configure channel dwell time
* support new DFS host confirmation feature in the firmware
ath
* update various regulatory mappings
wcn36xx
* various fixes to improve reliability
* add Factory Test Mode support
brmfmac
* add debugfs file for reading firmware capabilities
mwifiex
* support sysfs initiated device coredump
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Double Lo