This breaks out the measurement code to its own function
so we can handle this without swirling it up with the
big switch() statement inside ak8974_read_raw().
Keep a local s16 helper variable for the signed value
coming out of the measurement before assigning it to the
integer *val. The local variable makes the code easier
to read and the compiler will optimize it if possible.
Cc: Nick Reitemeyer <nick.reitemeyer@web.de>
Cc: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The HSCDTD008A has 15 bits of actual ADC valie, and the
AMI305 and AMI306 has 12 bits.
Correct this by providing an extra parameter to the channel
macro and define a separate set of channels for each variant
of the chip. The resolution is the actual resolution of the
internal ADC of the chip.
The values are stored in a S16 in 2's complement so all 16
bits are used for storing (no shifting needed).
The AMI305, AMI306 and HSCDTD008A valid bits are picked from
respective datasheet.
My best educated guess is that AK8974 is also 12 bits. The
AK8973 is an 8 bit and earlier version, and the sibling
drivers AMI305 and AMI306 are 12 bits, so it makes sense
to assume that the AK8974 is also 12 bits.
Cc: Nick Reitemeyer <nick.reitemeyer@web.de>
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The hscdtd008a is similar to the AK8974:
Only the whoami value and some registers are different.
Signed-off-by: Nick Reitemeyer <nick.reitemeyer@web.de>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This makes the driver code slightly easier to read.
Cc: Song Qiang <songqiang1304521@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Usual mix of new drivers, new support in old drivers and lots of minor
cleanup. Yaml conversions also continue to trickle in (plenty more to go!)
New device support
* ad7476
- Add ad7091 support (ID only)
* ad9467
- New driver for this 200/250 MSPS adi-axi-adc and SPI attached ADC.
* adi-axi-adc
- New driver to support ADIs generic AXI ADC IP core, used to provide
high speed interfaces to ADCs (JESD204B/C or parallel interfaces). Usually
paired with a device using a slow configuration interface (spi etc)
Includes DT bindings and some fixes for fpga headers.
* bmg160
- Add support for BMI088 (ID only)
* max1241
- New driver for this ADC.
* st_sensors
- Add support for LIS2HH12 accelerometer
* sx9310
- New driver supporting sx9310 and sx9311 proximity sensors.
Yaml DT binding conversions
* rockchip-saradc (including adding some missing parts)
* stm32-dac
* tsl2563
* vcnl4000
Features
* st_lsm6dsx
- Add LIS3MDL as a possible sensor hub device.
* vcnl4000
- Add new concept of near level (from DT) to provide to userspace which
often needs to have some calibrated concept of 'near'.
Cleanups, minor fixes etc.
* core
- Use snprintf for functions where strings are built and there is
potential for overflow.
- Correct docs to indicate mlock should not be used directly by drivers.
- Fix up accidental dropping of a patch to use bitmap_zalloc.
- Stop allowing enabling of buffers with no channels enabled.
- Drop unused 'stufftoread' from iio_buffer.
- Drop scan_el_attrs form iio_buffer as unused.
- Reorder sanity checks in __iio_device_register to fail earlier.
- Drop all the devm_ runregister / free functions from IIO as they
were never used and encourage poor design.
* dma-buffer
- Tidy up includes.
* dma-engine-buffer
- Provide dev-managed allocator.
- Fix an issue with printing a size_t
* cross subsystem (kxsd9, bmg160, mpu3050, bmi160, mpu6050, bmc150)
- Replace some unnecessary casts of error ptrs and whilst there.
use the %pe printf parameter to print them in a more useful fashion.
* cross subsystem
- Drop casts in calls to regmap_bulk_read as they make no sense.
- Use devm_platform_ioremap_resource to reduce boilerplate.
- Fix typos in Analog Devices.
* counters/104-quad
- Add Syed Nayyar Waris as an additional maintainer.
* ad7476
- Generate CONVST signal internally rather than requiring external
trigger. Add sysfs read back as can now do so.
- use devm_add_action_or_reset to tidy up error and remove handling.
* ad7793
- Switch to read_avail from explicit attribute. Mostly done to avoid
confusing people with a - sign (without surounding spaces) that
was correct but checkpatch didn't like.
* adis library
- Add missing newlines at end of error messages.
* adis16400
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* adis16460
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* ad_sigma_delta
- Move some channel definitions into individual drivers to avoid
having to deal with complex options.
* ak8974
- Silence an error on deffered probe.
* bmp280
- Harden against IRQ before registration.
- Convert to read_avail instead of opencoding the equivalent.
- Explicitly mark GPIO as optional.
- Cleanup casts.
- Remove line breaks from strings.
* htts221
- Replace direct access to platform_data with dev_get_platdata().
- Use device properties rather than device tree ones to allow ACPI
probing.
- Casting cleanups.
* intel_mrfld_adc
- Don't use unaligned accessor for aligned data.
* isl29125
- Reorder buer pre and post hooks to allow for coming core rework.
* ltc2983
- Remove comp to bool.
* max1363
- Stop using mlock from the iio_dev directly in favour of a local lock
with clearly defined scope.
* max30100
- Use generic device properties to allow ACPI probe.
* mpu6050
- Convert to i2c_new_client_device.
- Add debugfs register access.
* st_lsm6dsx
- Provide means of configuring full scale on slave device if supported.
- Drop include of st_sensors header to get one value. Its not otherwise
used by this driver.
* st-sensors
- Replace direct access to platform_data with dev_get_platdata().
- Casting cleanups.
- Avoid splitting strings.
* st_uvis25
- Casting cleanups.
* tsl2563
- Typo fix.
* tsl2772
- scnprintf in a non obvious string building usecase. Note also 'fixes'
a wrong calculation of remaining space that couldn't actually cause
any trouble as there was lots of room.
* xilinx-xadc
- Fix Lars-Peter spelling his own name wrong :) + additional typos.
-----BEGIN PGP SIGNATURE-----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=DyTF
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.8a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new IIO device support, features and cleanup for the 5.8 cycle
Usual mix of new drivers, new support in old drivers and lots of minor
cleanup. Yaml conversions also continue to trickle in (plenty more to go!)
New device support
* ad7476
- Add ad7091 support (ID only)
* ad9467
- New driver for this 200/250 MSPS adi-axi-adc and SPI attached ADC.
* adi-axi-adc
- New driver to support ADIs generic AXI ADC IP core, used to provide
high speed interfaces to ADCs (JESD204B/C or parallel interfaces). Usually
paired with a device using a slow configuration interface (spi etc)
Includes DT bindings and some fixes for fpga headers.
* bmg160
- Add support for BMI088 (ID only)
* max1241
- New driver for this ADC.
* st_sensors
- Add support for LIS2HH12 accelerometer
* sx9310
- New driver supporting sx9310 and sx9311 proximity sensors.
Yaml DT binding conversions
* rockchip-saradc (including adding some missing parts)
* stm32-dac
* tsl2563
* vcnl4000
Features
* st_lsm6dsx
- Add LIS3MDL as a possible sensor hub device.
* vcnl4000
- Add new concept of near level (from DT) to provide to userspace which
often needs to have some calibrated concept of 'near'.
Cleanups, minor fixes etc.
* core
- Use snprintf for functions where strings are built and there is
potential for overflow.
- Correct docs to indicate mlock should not be used directly by drivers.
- Fix up accidental dropping of a patch to use bitmap_zalloc.
- Stop allowing enabling of buffers with no channels enabled.
- Drop unused 'stufftoread' from iio_buffer.
- Drop scan_el_attrs form iio_buffer as unused.
- Reorder sanity checks in __iio_device_register to fail earlier.
- Drop all the devm_ runregister / free functions from IIO as they
were never used and encourage poor design.
* dma-buffer
- Tidy up includes.
* dma-engine-buffer
- Provide dev-managed allocator.
- Fix an issue with printing a size_t
* cross subsystem (kxsd9, bmg160, mpu3050, bmi160, mpu6050, bmc150)
- Replace some unnecessary casts of error ptrs and whilst there.
use the %pe printf parameter to print them in a more useful fashion.
* cross subsystem
- Drop casts in calls to regmap_bulk_read as they make no sense.
- Use devm_platform_ioremap_resource to reduce boilerplate.
- Fix typos in Analog Devices.
* counters/104-quad
- Add Syed Nayyar Waris as an additional maintainer.
* ad7476
- Generate CONVST signal internally rather than requiring external
trigger. Add sysfs read back as can now do so.
- use devm_add_action_or_reset to tidy up error and remove handling.
* ad7793
- Switch to read_avail from explicit attribute. Mostly done to avoid
confusing people with a - sign (without surounding spaces) that
was correct but checkpatch didn't like.
* adis library
- Add missing newlines at end of error messages.
* adis16400
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* adis16460
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* ad_sigma_delta
- Move some channel definitions into individual drivers to avoid
having to deal with complex options.
* ak8974
- Silence an error on deffered probe.
* bmp280
- Harden against IRQ before registration.
- Convert to read_avail instead of opencoding the equivalent.
- Explicitly mark GPIO as optional.
- Cleanup casts.
- Remove line breaks from strings.
* htts221
- Replace direct access to platform_data with dev_get_platdata().
- Use device properties rather than device tree ones to allow ACPI
probing.
- Casting cleanups.
* intel_mrfld_adc
- Don't use unaligned accessor for aligned data.
* isl29125
- Reorder buer pre and post hooks to allow for coming core rework.
* ltc2983
- Remove comp to bool.
* max1363
- Stop using mlock from the iio_dev directly in favour of a local lock
with clearly defined scope.
* max30100
- Use generic device properties to allow ACPI probe.
* mpu6050
- Convert to i2c_new_client_device.
- Add debugfs register access.
* st_lsm6dsx
- Provide means of configuring full scale on slave device if supported.
- Drop include of st_sensors header to get one value. Its not otherwise
used by this driver.
* st-sensors
- Replace direct access to platform_data with dev_get_platdata().
- Casting cleanups.
- Avoid splitting strings.
* st_uvis25
- Casting cleanups.
* tsl2563
- Typo fix.
* tsl2772
- scnprintf in a non obvious string building usecase. Note also 'fixes'
a wrong calculation of remaining space that couldn't actually cause
any trouble as there was lots of room.
* xilinx-xadc
- Fix Lars-Peter spelling his own name wrong :) + additional typos.
* tag 'iio-for-5.8a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (101 commits)
iio: magnetometer: ak8974: Silence deferred-probe error
Documentation: ABI: document IIO in_proximity_nearlevel file
iio: vcnl4000: Export near level property for proximity sensor
dt-bindings: iio: light: vcnl4000: Add proximity-near-level
dt-bindings: iio: Introduce common properties for iio sensors
dt-bindings: iio: vcnl4000: convert bindings to YAML format
iio: Fix misspellings of "Analog Devices"
iio: light: isl29125: fix iio_triggered_buffer_{predisable,postenable} positions
iio: adc: fsl-imx25-gcq: Use devm_platform_ioremap_resource
iio: adc: at91-adc: Use devm_platform_ioremap_resource
iio: adc: sun4i-gpadc-iio: Use devm_platform_ioremap_resource
iio:light:ltr501: Drop unnecessary cast of parameter in regmap_bulk_read
iio:magn:mmc35240: Drop unnecessary casts of val parameter in regmap_bulk*
iio:imu:mpu6050: Tidy up parameters to regmap_bulk functions.
iio:chemical:bme680: Tidy up parameters to regmap_bulk_read
iio:chemical:atlas-sensor: Drop unnecessary explicit casts in regmap_bulk_read calls
iio:accel:mxc4005: Drop unnecessary explicit casts in regmap_bulk_read calls
iio: imu: st_lsm6dsx: drop huge include in sensor-hub driver
iio: buffer: drop devm_iio_kfifo_free() API call
iio: buffer: drop devm_iio_hw_consumer_free() API call
...
It's not uncommon that voltage regulator becomes available later during
kernel's boot process. This patch adds info message about unavailable
regulators in a case of the deferred-probe error and also amends the
error message with a error code.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Given the parameter is void *, casting to u8 * is unnecessary.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Utilize %pe format specifier from vsprintf while printing error logs
with dev_err(). Discards the use of unnecessary explicit casting and
prints symbolic error name which might prove to be convenient during
debugging.
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In few places the unnecessary explicit castings are being used.
Drop them for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
At the moment, reading from in_magn_*_raw in sysfs tends to return
large values around 65000, even though the output of ak8974 is actually
limited to ±32768. This happens because the value is never converted
to the signed 16-bit integer variant.
Add an explicit cast to s16 to fix this.
Fixes: 7c94a8b2ee ("iio: magn: add a driver for AK8974")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Waleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert to use device_get_match_data() instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since IIO framework supports device property API and driver has been moved
already to the use of GPIO descriptors the logical continuation is to
get rid of platform data completely. We are on the safe side here since
there are no users of it in the kernel.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Device property API allows to gather device resources from different sources,
such as ACPI. Convert the drivers to unleash the power of device property API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since we have access to the struct device_driver and thus to the ID table,
there is no need to supply special parameters to st_sensors_of_name_probe().
Besides that we have a common API to get driver match data, there is
no need to do matching separately for OF and ACPI.
Taking into consideration above, simplify the ST sensors code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The end-of-conversion (EOC) GPIO line is better to grab using
a GPIO descriptor. We drop the pdata for this: clients using board
files can use machine descriptor tables to pass this GPIO from
static data.
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
None of the ST sensor drivers use any symbols from
<linux/gpio.h>, just drop the include from all of them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch is removing the buffer allocation at each buffer enable.
We just allocate enough memory in the main structure during probe
to cover maximum size needed (that anyway is pretty small) [16bytes].
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Not even sure why it was there since the beginning. Just use IRQ
number in the sensor_data struct.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch is trying to cleanup for good the buffers operation functions.
Let's rename the goto label using operation to perform and not
where it fails.
Not stable material as not fixing a 'bug' but rather bringing the
driver in line with general 'patterns' to allow a subsystem wide
cleanup.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Everything is about mmc35240_ except MMC53240_WAIT_SET_RESET (3 and 5
switched).
This is likely a typo. Define and use MMC35240_WAIT_SET_RESET instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch is meant to replace the i2c/spi transfer functions with
regmap. SPI framework requires DMA safe buffers so let's add GFP_DMA
flag for memory allocation used by bulk_read functions.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some devices need to be configured with special bit in order to
use spi 3-wire. This was done during device identification phase.
Instead, let's move this part as spi specific.
Doing this the check_device_support function becomes a simple
device id check, so let's rename it.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch set magn settings right after probe start. This is
done in preparation of regmap that needs different configuration
based on multiread bit value.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The function is introduced to retrieve magn device settings. It will be
used by probe in order to configure regmap.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 111 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.567572064@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this file is subject to the terms and conditions of version 2 of the
gnu general public license see the file copying in the main
directory of this archive for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 55 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.108941081@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
licensed under the gpl 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 135 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170026.071193225@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
51 franklin street fifth floor boston ma 02110 1301 usa
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option [no]_[pad]_[ctrl] any later version this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin street fifth floor boston ma
02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 176 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.652910950@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_regmap_init_i2c may fail and return NULL. The fix returns
the error when it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
- use temporary variable in get_mount_matrix()
- remove , after { }
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch allows to read a mount-matrix device tree
property and report to user-space or in-kernel iio
clients.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch allows to read a mount-matrix device tree
property and report to user-space or in-kernel iio
clients.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently mount matrix is allowed in Device Tree, though there is
no technical issue to extend it to support ACPI.
Convert the function to use device_property_read_string_array() and
thus allow to read mount matrix from ACPI if available.
Example of use in _DSD method:
Name (_DSD, Package ()
{
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package () { "mount-matrix", Package() {
"1", "0", "0",
"0", "0.866", "0.5",
"0", "-0.5", "0.866",
} },
}
})
At the same time drop the "of" prefix from its name and
convert current users.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The magnetometer's power supplies could be controllable on some platforms,
such as i.MX6Q-SABRESD board, the mag3110's power supplies are controlled
by a GPIO fixed regulator, need to make sure the regulators are enabled
before any communication with mag3110, this patch adds vdd/vddio regulator
operation support.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Staging graduation
* ad2s90
- Driver for this resolver to digital chip.
New drivers and device support.
* ad5686
- Add support for ad5310r DAC and associated fix in value read back.
* exynos-adc
- Support for S5PV210 which is slightly different from other parts.
* mcp41010
- Driver supporting MCP41010, MCP41050, MCP41100, MCP42010, MCP42050 and
MCP42100 microchip potentiometers.
New ACPI ids.
* ak8975
- AKM9911 ACPI HID.
* kxcjk-1013
- KXJ2109 ACPI HID.
- KIOX010A ACPI HID.
New features
* ad5933
- Explicit DT binding.
* ad2s90
- Explicit DT binding including dropping spi setup that is done via dt
in favour of verifying the settings form DT.
* adt7316
- Explicit DT binding and support for gpio, irq_flags etc.
* stm32-adc
- Runtime power management.
Minor fixes and cleanups
* core
- Protect against missing info structure.
* ad2s90
- SPDX
- Add documentation fo the mutex.
* ad7280a
- Check allocation failure.
- Fix an accidental replacement of an error return.
* adt7316
- Switch some variables to be local and rename for consistency with other
drivers.
- Revert a false handling of 0 as an error introduced earlier this cycle.
* bmi160
- Use devm functions throughout probe() to avoid need for remove().
* hid-sensor-hub
- White space cleanup.
* hts221
- MAINTAINERS entry.
* lis302
- Use generic name in the DT binding doc.
* Messon-saradc
- Check for allocation error.
- Fix some presented clock names that break clk debugfs.
* qcom-spmi-adc
- A fix for initialization of the prescale property. Came late in the
cycle, so merge window is probably the best route for this.
* st_lsm6dsx
- Allow for variable read length to support wider range of slave devices.
-----BEGIN PGP SIGNATURE-----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=+vyl
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.21b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanups for the 4.21 cycle.
Staging graduation
* ad2s90
- Driver for this resolver to digital chip.
New drivers and device support.
* ad5686
- Add support for ad5310r DAC and associated fix in value read back.
* exynos-adc
- Support for S5PV210 which is slightly different from other parts.
* mcp41010
- Driver supporting MCP41010, MCP41050, MCP41100, MCP42010, MCP42050 and
MCP42100 microchip potentiometers.
New ACPI ids.
* ak8975
- AKM9911 ACPI HID.
* kxcjk-1013
- KXJ2109 ACPI HID.
- KIOX010A ACPI HID.
New features
* ad5933
- Explicit DT binding.
* ad2s90
- Explicit DT binding including dropping spi setup that is done via dt
in favour of verifying the settings form DT.
* adt7316
- Explicit DT binding and support for gpio, irq_flags etc.
* stm32-adc
- Runtime power management.
Minor fixes and cleanups
* core
- Protect against missing info structure.
* ad2s90
- SPDX
- Add documentation fo the mutex.
* ad7280a
- Check allocation failure.
- Fix an accidental replacement of an error return.
* adt7316
- Switch some variables to be local and rename for consistency with other
drivers.
- Revert a false handling of 0 as an error introduced earlier this cycle.
* bmi160
- Use devm functions throughout probe() to avoid need for remove().
* hid-sensor-hub
- White space cleanup.
* hts221
- MAINTAINERS entry.
* lis302
- Use generic name in the DT binding doc.
* Messon-saradc
- Check for allocation error.
- Fix some presented clock names that break clk debugfs.
* qcom-spmi-adc
- A fix for initialization of the prescale property. Came late in the
cycle, so merge window is probably the best route for this.
* st_lsm6dsx
- Allow for variable read length to support wider range of slave devices.
* tag 'iio-for-4.21b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (37 commits)
iio: adc: qcom-spmi-adc5: Initialize prescale properly
dt-bindings: iio: adc: exynos-adc: Add S5PV210 variant
iio: adc: Allow selection of Exynos ADC on S5PV210
iio: adc: exynos-adc: Add S5PV210 variant
iio: bmi160: use all devm functions in probe
iio: dac: ad5686: fix bit shift read register
iio:dac:ad5686: Add AD5310R support
Revert "Staging: iio: adt7316: Add an extra check for 'ret' equals to 0"
dt-bindings: iio: accel: use a generic node name for lis302
iio: core: check 'info' value before registering the device
staging: iio: adc: ad7280a: fix overwrite of the returned value
staging: iio: adc: ad7280a: check for devm_kasprint() failure
iio: humidity: hts221: add entry in MAINTAINERS file
iio: magnetometer: ak8975: Add the "AKM9911" ACPI HID
staging:iio:ad2s90: Move out of staging
staging:iio:ad2s90: Add comment to device state mutex
staging:iio:ad2s90: Replace license text w/ SPDX identifier
dt-bindings:iio:resolver: Add docs for ad2s90
staging:iio:ad2s90: Add max frequency check at probe
staging:iio:ad2s90: Remove spi setup that should be done via dt
...
This HID is used on the ASUS MeMO Pad 7 (ME176C) tablet.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
PNI RM3100 is a high resolution, large signal immunity magnetometer,
composed of 3 single sensors and a processing chip with a MagI2C
interface.
Following functions are available:
- Single-shot measurement from
/sys/bus/iio/devices/iio:deviceX/in_magn_{axis}_raw
- Triggerd buffer measurement.
- DRDY pin for data ready trigger.
- Both i2c and spi interface are supported.
- Both interrupt and polling measurement is supported, depends on if
the 'interrupts' in DT is declared.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Before this commit sensor_hub_input_attr_get_raw_value() failed to take
the signedness of 16 and 8 bit values into account, returning e.g.
65436 instead of -100 for the z-axis reading of an accelerometer.
This commit adds a new is_signed parameter to the function and makes all
callers pass the appropriate value for this.
While at it, this commit also fixes up some neighboring lines where
statements were needlessly split over 2 lines to improve readability.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
LIS3MDL and LSM9DS1 are missing BDU settings in their register maps, so add
them. I don't have a LIS3MDL sensor to test, but this works correctly on
the LSM9DS1, which has the same register map.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Update the sensor settings to support the LSM9DS1 sensor. Although the
LSM9DS1 accelerometer and gyroscope are coupled together to use the same
FIFO, the magnetometer is separate and can be cleanly supported without
refactoring the existing driver.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add a comment clarifying better when to use <device_name> vs
<device_name>-magn in compatibility strings.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, we enable the device before we enable the device trigger. At
high frequencies, this can cause interrupts that don't yet have a poll
function associated with them and are thus treated as spurious. At high
frequencies with level interrupts, this can even cause an interrupt storm
of repeated spurious interrupts (~100,000 on my Beagleboard with the
LSM9DS1 magnetometer). If these repeat too much, the interrupt will get
disabled and the device will stop functioning.
To prevent these problems, enable the device prior to enabling the device
trigger, and disable the divec prior to disabling the trigger. This means
there's no window of time during which the device creates interrupts but we
have no trigger to answer them.
Fixes: 90efe05562 ("iio: st_sensors: harden interrupt handling")
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Tested-by: Denis Ciocca <denis.ciocca@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Miscellaneous cleanup to fix minor consistency, grammar, and spelling
issues.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Adds the ability to run the Mag3110 in continuous mode to speed up the
sampling rate.
Depending on the sampling rate requested the device can be put in or out
of continuous mode automatically.
Shifting out of continuous mode requires a potential 1 / ODR wait which
is also implemented.
Modified the sleep method when data is not ready to allow for
sampling > 50sps to work.
Signed-off-by: Richard Tresidder <rtresidd@electromag.com.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The function magn_3d_read_raw has a switch statement handling multiple
cases per channel. The first case statement uses the magic number 0,
which means IIO_CHAN_INFO_RAW. Additionally, the iio_chan_spec for
magn_3d_channels is configured to be IIO_CHAN_INFO_RAW. Therefore, this
patch replaces the magic number 0 for the appropriate IIO_CHAN_INFO_RAW.
Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add new ACPI ID for ak9911 as had been found on prototype board.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd atomisp
cleanups (take the media tree's version).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnFrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymxbwCgtNlBkqD2JJYpLRKvI/C4w1vzZsEAnA2THRkt
g3ioPBqmqC/2DSbldr2o
=/ebw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd
atomisp cleanups (take the media tree's version)"
* tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits)
staging: lustre: add SPDX identifiers to all lustre files
staging: greybus: Remove redundant license text
staging: greybus: add SPDX identifiers to all greybus driver files
staging: ccree: simplify ioread/iowrite
staging: ccree: simplify registers access
staging: ccree: simplify error handling logic
staging: ccree: remove dead code
staging: ccree: handle limiting of DMA masks
staging: ccree: copy IV to DMAable memory
staging: fbtft: remove redundant initialization of buf
staging: sm750fb: Fix parameter mistake in poke32
staging: wilc1000: Fix bssid buffer offset in Txq
staging: fbtft: fb_ssd1331: fix mirrored display
staging: android: Fix checkpatch.pl error
staging: greybus: loopback: convert loopback to use generic async operations
staging: greybus: operation: add private data with get/set accessors
staging: greybus: loopback: Fix iteration count on async path
staging: greybus: loopback: Hold per-connection mutex across operations
staging: greybus/loopback: use ktime_get() for time intervals
staging: fsl-dpaa2/eth: Extra headroom in RX buffers
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPI Serial Interface Mode (SIM) register information to
LIS3MDL magn sensor
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Separate data-ready configuration parameters for INT1 and INT2 pins in
st_sensor_data_ready_irq data structure. That change will be use to
properly support LIS2DW12 accel sensor.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce register mask for data-ready status register since
pressure sensors (e.g. LPS22HB) export just two channels
(BIT(0) and BIT(1)) and BIT(2) is marked reserved while in
st_sensors_new_samples_available() value read from status register
is masked using 0x7.
Moreover do not mask status register using active_scan_mask since
now status value is properly masked and if the result is not zero the
interrupt has to be consumed by the driver. This fix an issue on LPS25H
and LPS331AP where channel definition is swapped respect to status
register.
Furthermore that change allows to properly support new devices
(e.g LIS2DW12) that report just ZYXDA (data-ready) field in status register
to figure out if the interrupt has been generated by the device.
Fixes: 97865fe413 (iio: st_sensors: verify interrupt event to status)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.
A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.
New device support
* ad5446
- add ids to support compatible parts DAC081S101, DAC101S101,
DAC121S101.
- add the dac7512 id and drop the misc driver as feeling is no
one is using it (was introduced for a board that is long obsolete)
* mt6577
- add bindings for mt2712 which is fully compatible with other
supported parts.
* st_pressure
- add support for LPS33HW and LPS35HW with bindings (ids mostly).
New features
* ccs811
- Add support for the data ready trigger.
* mma8452
- remove artifical restriction on supporting multiple event types
at the same time.
* tcs3472
- support out of threshold events
Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
struct iio_info or struct iio_trigger_ops. This is similar to
work done in a number of other subsystems (e.g. i2c, spi).
All drivers are fixed and then the fields in these structures are
removed.
This will cause build failures for out of tree drivers and any
new drivers that cross with this work going into the kernel.
Note mostly done with a coccinelle patch, included in the series
on the mailing list but not merged as the fields no longer exist
in the structures so the any hold outs will cause a build failure.
Cleanups
* ads1015
- avoid writing config register when it doesn't change.
- add 10% to conversion wait time as it seems it is sometimes
a little small.
* ade7753
- replace use of core mlock with a local lock. This is part of a
long term effort to make the use of mlock opaque and single
purpose.
* ade7759
- expand the use of buf_lock to cover previous mlock cases. This
is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
- drop an unused variable
* inv_mpu6050
- add a missing break in a switch for consistency - not actual
bug,
- make some local arrays static to save on object code size.
* max5481
- drop manual setting of the spi module owner as handled by the
spi core.
* max5487
- drop manual setting of the spi module owner as handled by the
spi core.
* max9611
- drop explicit setting of the i2c module owner as handled by
the i2c core.
* mcp320x
- speed up reads on single channel devices,
- drop unused of_device_id data elements,
- document the struct mcp320x,
- improve binding docs to reflect restrictions on spi setup and
to make it explicit that the reference regulator is needed.
* mma8452
- symbolic to octal permissions,
- unsigned to unsigned int.
* st_lsm6dsx
- avoid setting odr values multiple times,
- drop config of LIR as it is only ever set to the existing
defaults,
- drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
- drop manual setting of the spi module owner as handled by the
spi core.
* tsl2x7x
- constify the i2c_device_id,
- cleanup limit checks to avoid static checker warnings (and generally
have nicer code).
-----BEGIN PGP SIGNATURE-----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=ik5C
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.15a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Round one of new device support, features and cleanup for IIO in the 4.15 cycle.
Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.
A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.
New device support
* ad5446
- add ids to support compatible parts DAC081S101, DAC101S101,
DAC121S101.
- add the dac7512 id and drop the misc driver as feeling is no
one is using it (was introduced for a board that is long obsolete)
* mt6577
- add bindings for mt2712 which is fully compatible with other
supported parts.
* st_pressure
- add support for LPS33HW and LPS35HW with bindings (ids mostly).
New features
* ccs811
- Add support for the data ready trigger.
* mma8452
- remove artifical restriction on supporting multiple event types
at the same time.
* tcs3472
- support out of threshold events
Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
struct iio_info or struct iio_trigger_ops. This is similar to
work done in a number of other subsystems (e.g. i2c, spi).
All drivers are fixed and then the fields in these structures are
removed.
This will cause build failures for out of tree drivers and any
new drivers that cross with this work going into the kernel.
Note mostly done with a coccinelle patch, included in the series
on the mailing list but not merged as the fields no longer exist
in the structures so the any hold outs will cause a build failure.
Cleanups
* ads1015
- avoid writing config register when it doesn't change.
- add 10% to conversion wait time as it seems it is sometimes
a little small.
* ade7753
- replace use of core mlock with a local lock. This is part of a
long term effort to make the use of mlock opaque and single
purpose.
* ade7759
- expand the use of buf_lock to cover previous mlock cases. This
is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
- drop an unused variable
* inv_mpu6050
- add a missing break in a switch for consistency - not actual
bug,
- make some local arrays static to save on object code size.
* max5481
- drop manual setting of the spi module owner as handled by the
spi core.
* max5487
- drop manual setting of the spi module owner as handled by the
spi core.
* max9611
- drop explicit setting of the i2c module owner as handled by
the i2c core.
* mcp320x
- speed up reads on single channel devices,
- drop unused of_device_id data elements,
- document the struct mcp320x,
- improve binding docs to reflect restrictions on spi setup and
to make it explicit that the reference regulator is needed.
* mma8452
- symbolic to octal permissions,
- unsigned to unsigned int.
* st_lsm6dsx
- avoid setting odr values multiple times,
- drop config of LIR as it is only ever set to the existing
defaults,
- drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
- drop manual setting of the spi module owner as handled by the
spi core.
* tsl2x7x
- constify the i2c_device_id,
- cleanup limit checks to avoid static checker warnings (and generally
have nicer code).
Note this includes fixes from recent merge window. As such the tree
is based on top of a prior staging/staging-next tree.
* iio core
- return and error for a failed read_reg debugfs call rather than
eating the error.
* ad7192
- Use the dedicated reset function in the ad_sigma_delta library
instead of an spi transfer with the data on the stack which
could cause problems with DMA.
* ad7793
- Implement a dedicate reset function in the ad_sigma_delta library
and use it to correctly reset this part.
* bme280
- ctrl_reg write must occur after any register writes
for updates to take effect.
* mcp320x
- negative voltage readout was broken.
- Fix an oops on module unload due to spi_set_drvdata not being called
in probe.
* st_magn
- Fix the data ready line configuration for the lis3mdl. It is not
configurable so the st_magn core was assuming it didn't exist
and so wasn't consuming interrupts resulting in an unhandled
interrupt.
* stm32-adc
- off by one error on max channels checking.
* stm32-timer
- preset should not be buffered - reorganising register writes avoids
this.
- fix a corner case in which write preset goes wrong when a timer is
used first as a trigger then as a counter with preset. Odd case but
you never know.
* ti-ads1015
- Fix setting of comparator polarity by fixing bitfield definition.
* twl4030
- Error path handling fix to cleanup in event of regulator
registration failure.
- Disable the vusb3v1 regulator correctly in error handling
- Don't paper over a regulator enable failure.
-----BEGIN PGP SIGNATURE-----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=CcjQ
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.14a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of IIO fixes for the 4.14 cycle
Note this includes fixes from recent merge window. As such the tree
is based on top of a prior staging/staging-next tree.
* iio core
- return and error for a failed read_reg debugfs call rather than
eating the error.
* ad7192
- Use the dedicated reset function in the ad_sigma_delta library
instead of an spi transfer with the data on the stack which
could cause problems with DMA.
* ad7793
- Implement a dedicate reset function in the ad_sigma_delta library
and use it to correctly reset this part.
* bme280
- ctrl_reg write must occur after any register writes
for updates to take effect.
* mcp320x
- negative voltage readout was broken.
- Fix an oops on module unload due to spi_set_drvdata not being called
in probe.
* st_magn
- Fix the data ready line configuration for the lis3mdl. It is not
configurable so the st_magn core was assuming it didn't exist
and so wasn't consuming interrupts resulting in an unhandled
interrupt.
* stm32-adc
- off by one error on max channels checking.
* stm32-timer
- preset should not be buffered - reorganising register writes avoids
this.
- fix a corner case in which write preset goes wrong when a timer is
used first as a trigger then as a counter with preset. Odd case but
you never know.
* ti-ads1015
- Fix setting of comparator polarity by fixing bitfield definition.
* twl4030
- Error path handling fix to cleanup in event of regulator
registration failure.
- Disable the vusb3v1 regulator correctly in error handling
- Don't paper over a regulator enable failure.
Data-ready line in LIS3MDL is routed to drdy pin and it is not possible
to select a different INT pin. st_sensors_set_dataready_irq() assumes
that if drdy int address is not exported in register map, irq trigger
is not supported by the sensor and hw_irq_trigger is always false.
Based on this configuration st_sensors_irq_thread does not consume
generated interrupt causing an unhandled irq.
Fix this taking into account status register address in
st_sensors_set_dataready_irq()
Fixes: 90efe05562 (iio: st_sensors: harden interrupt handling)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Use AMI306 calibration data for randomness and debugging.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove IRQ active low support for LSM303AGR since the sensor does not
support that capability for data-ready line
Fixes: a9fd053b56 (iio: st_sensors: support active-low interrupts)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reading INT_CLEAR has side effects - disallow reading it via debugfs.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Mix device-specific data into randomness pool.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for AMI306 magnetometer - very similar to AMI305.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
add support to STMicroelectronics LIS2MDL magnetometer in
st_magn framework
http://www.st.com/resource/en/datasheet/lis2mdl.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add device tree support for LIS3MDL and LSM303AGR magnetometer sensors
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Don't inflate the kernel size with data that isn't used. The conditional
declaration also fixes the following warning when building with clang:
drivers/iio/magnetometer/ak8975.c:704:36: error: variable 'ak_acpi_match'
is not needed and will not be emitted
[-Werror,-Wunneeded-internal-declaration]
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Move st_sensors_of_i2c_probe() in st_sensors_core and rename it in
st_sensors_of_name_probe(). That change is necessary to add device-tree
support in spi code otherwise the rest of the autodetection will fail
since spi->modalias (and indio_dev->name) will be set using compatible
string value that differs from standard sensor name
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Enable multiread by default for LIS3MDL since using I2C interface
the subaddr Msb is used to automatically increase the slave address
during multiple data read/write. In the same way, using SPI interface,
bit 1 in register address is used to enable auto-increment of the slave
address in multiple read/write.
Fixes: 872e79add7 (iio:magn: Add STMicroelectronics magn driver)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Remove LSM303DLHC, LSM303DLM from st_magn_id_table since LSM303DL series
does not support spi interface
Fixes: 872e79add7 (iio: magn: Add STMicroelectronics magn driver)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Even if bus is not hot-pluggable, devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Driver was checking for direct mode but not locking it. Use
claim/release helper functions to guarantee the device stays
in direct mode during raw writes.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
At the end of the delay loop timeout will always be zero
and hence the check for !timeout will always be true. Remove
the redundant check and the redundant return 0 at the end of
the function.
Fixes CoverityScan CID#1357168 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There are 2 usage types (Magnetic Flux and Heading data field) for HID
compass sensor, thus the values of offset, scale, and sensitivity should
be separated according to their respective usage type. The changes made
are as below:
1. Hysteresis: A struct hid_sensor_common rot_attributes is created in
struct magn_3d_state to contain the sensitivity for IIO_ROT.
2. Scale: scale_pre_decml and scale_post_decml are separated for IIO_MAGN
and IIO_ROT.
3. Offset: Same as scale, value_offset is separated for IIO_MAGN and
IIO_ROT.
For sensitivity, HID_USAGE_SENSOR_ORIENT_MAGN_FLUX and
HID_USAGE_SENSOR_ORIENT_MAGN_HEADING are used for sensivitity fields based
on the HID Sensor Usages specifications. Hence, these changes are added on
the sensitivity field.
Signed-off-by: Ooi, Joyce <joyce.ooi@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We have #defines for all the individual sensor registers and
value/mask pairs #defined at the top of the file and used at
exactly one spot.
This is usually good if the #defines give a meaning to the
opaque magic numbers.
However in this case, the semantic meaning is inherent in the
name of the C99-addressable fields, and that means duplication
of information, and only makes the code hard to maintain since
you every time have to add a new #define AND update the site
where it is to be used.
Get rid of the #defines and just open code the values into the
appropriate struct elements. Make sure to explicitly address
the .hz and .value fields in the st_sensor_odr_avl struct
so that the meaning of all values is clear.
This patch is purely syntactic should have no semantic effect.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fixes two cases of 'cast to restricted __le16' as reported by sparse.
Signed-off-by: Ico Doornekamp <ico@pruts.nl>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ak8974_configure() function is used only from the PM code,
but that can be hidden when CONFIG_PM is disabled:
drivers/iio/magnetometer/ak8974.c:201:12: error: 'ak8974_configure' defined but not used [-Werror=unused-function]
This replaces the #ifdef with a __maybe_unused annotation, which
will work correctly in all configurations and avoid the warning,
as the compiler can now see where ak8974_configure is called from.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 7c94a8b2ee ("iio: magn: add a driver for AK8974")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Driver was checking for direct mode but not locking it. Use
claim/release helper functions to guarantee the device stays
in direct mode during raw reads.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds a driver for the Asahi Kasei AK8974 and its sibling
AMI305 magnetometers. It was deployed on scale in 2009 on a
multitude of devices. It is distincly different from AK8973
and AK8975 and needs its own driver.
This patch is based on the long lost work of Samu Onkalo at Nokia,
who made a misc character device driver for the Maemo/MeeGo Nokia
devices, before the time of the IIO subsystem. It was mounted in e.g.
the Nokia N950, N8, N86, N97 etc. It is also mounted on the
ST-Ericsson HREF reference designs.
It works nicely in sysfs:
$ cat in_magn_x_raw && cat in_magn_y_raw && cat in_magn_z_raw
-55
-101
161
And with buffered reads using a simple HRTimer trigger:
$ generic_buffer -c10 -a -n ak8974 -t foo
iio device number being used is 3
iio trigger number being used is 2
No channels are enabled, enabling all channels
Enabling: in_magn_x_en
Enabling: in_magn_y_en
Enabling: in_magn_z_en
Enabling: in_timestamp_en
/sys/bus/iio/devices/iio:device3 foo
-58.000000 -102.000000 157.000000 946684970985321044
-60.000000 -98.000000 159.000000 946684971012237548
-60.000000 -106.000000 163.000000 946684971032257080
-62.000000 -94.000000 169.000000 946684971052185058
-58.000000 -98.000000 163.000000 946684971072204589
-54.000000 -100.000000 163.000000 946684971092224121
-53.000000 -103.000000 164.000000 946684971112731933
-50.000000 -102.000000 165.000000 946684971132232666
-61.000000 -101.000000 164.000000 946684971152191162
-57.000000 -99.000000 168.000000 946684971172210693
Disabling: in_magn_x_en
Disabling: in_magn_y_en
Disabling: in_magn_z_en
Disabling: in_timestamp_en
I cannot currently scale these raw values to gauss. This is
because of lack of documentation. I have sent a request for
a datasheet to Asahi Kasei.
The driver can optionally use a DRDY line IRQ to capture data,
else it will sleep and poll.
Cc: Samu Onkalo <samu.onkalo@intel.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds runtime PM support to the AK8975 driver. It solves two
problems:
- After reading the first value the chip was left in MODE_ONCE,
meaning (presumably) it may be consuming more power. Now the
runtime PM hooks kick in and set it to POWER_DOWN.
- Regulators were simply enabled and left on, making it
impossible to turn the power consuming regulators off because
of the increased refcount. We now disable the regulators at
autosuspend.
- We also handle system suspend: by using pm_runtime_force_suspend()
and pm_runtime_force_resume() from the system PM sleep hooks,
the runtime PM code is managing the power also for this case.
It is currently not completely optimal: when the system resumes
the AK8975 goes into active mode even if noone is going to use
it: currently the force calls need to be paired, but the runtime
PM people are working on making it possible to leave devices
runtime suspended when coming back from sleep.
Inspired by my work on the BH1780 light sensor driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The code was not powering the magnetometer down properly at
remove(): just cutting the regulators without first setting the
device in power off mode. Fix this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The datasheet actually specifies that we need to wait atleast
500us after powering on the device before trying to set mode.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Move the regulator_get() calls directly into the probe() function,
keep only the power_on()/power_off() functions to flick the
regulators on/off.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The AK8975 has two power sources: Vdd (analog voltage supply)
and Vid (digital voltage supply). Optionally also obtain the Vid
supply regulator and enable it.
If an error occurs when enabling one of the regulators: bail out.
Cc: Gregor Boirie <gregor.boirie@parrot.com>
Cc: Richard Leitner <dev@g0hl1n.net>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
IS_ERR_OR_NULL() should never be used with regulators because
a NULL pointer may be a perfectly valid dummy regulator
We should always succeed to fetch and enable a regulator, but
it may be a dummy. That is fine, so bail out for any real
errors or probe deferrals
Include the error code in the warning print so we know what
kind of problem we're dealing with (for example it is nice to
see if it is a probe deferral).
As we will bail out of probe if the regulator is erroneous,
just issue regulator_disable() on the poweroff path: it will
succeed.
Cc: Mark Brown <broonie@kernel.org>
Cc: Lars-Peter Clausen Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Adds a new per-device sysfs attribute "current_timestamp_clock" to allow
userspace to select a particular POSIX clock for buffered samples and
events timestamping.
Following clocks, as listed in clock_gettime(2), are supported:
CLOCK_REALTIME, CLOCK_MONOTONIC, CLOCK_MONOTONIC_RAW,
CLOCK_REALTIME_COARSE, CLOCK_MONOTONIC_COARSE, CLOCK_BOOTTIME and
CLOCK_TAI.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We want the fixes in here, and we can resolve a merge issue in
drivers/iio/industrialio-trigger.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New device support
* ads1015
- add ads1115 support
* bma220 accelerometer
- new driver
- triggered buffer support.
* bmc150
- add bmm150 support.
* bmp280
- bme280 support with addition of humidity channel.
* max5487 potentiometer
- new driver
* MMA7660FC accelerometer.
- New driver
* st-pressure
- support for the lps22hb
* loop trigger.
- This one is *nasty* but we have real applications (parrot drones) where
it is useful. The trigger basically spins as hard as it can firing off
a new trigger each time all triggered devices come back to say they are
done. It doesn't hang a machine even when doing it on a dummy driver.
A lot nicer than having this implemented within lots of device drivers
anyway.
Core stuff
* Add support to create IIO devices via configfs (similar to we did for
triggers a while back) + docs.
* New channel types
- IIO_ELECTRICAL_CONDUCTIVITY
* Couple of MAINTAINERS patches to list the device tree bindings.
* Make trigger ops structure non optional (comment fix). It hasn't been for
an awful long time, but that's not what the description said.
New features
* ak8975
- support adapters that are limited to byte data only by allowing the
emulated block read i2c function that was recently introduced.
* atlas-ph
- support atlas-ec (electrical conductivity sensor)
* bmi160
- add available frequency and scale attributes to make the driver
more user friendly (and avoid having to read the datasheet to know
what will work).
* dummy
- move creation to configfs interface. It's not real hardware so we
are not that worried about the ABI breakage ;)
* mma8452
- oversampling ration support
* nau7802
- expose available gains to make life easier for userspace.
* st-sensors
- allow use of emulation for SMBus block reads as all the st parts support
it.
* ti-ads1015
- list datasheet names to allow their use by inkernel consumers.
* Various module alias additions to help auto probing. Drop one redundant one
as well.
Cleanups
* ad7266, ad7476, ad7887, ad7923, ad799x
- use direct mode claim function rather than open coding it during sensor
read (prevents switching on buffers mid read).
* ad7793, ad7791
- use direct mode claim to prevent frequency changes when buffers running.
* afe440x - These are ABI breaking but the driver requires custom userspace
code to do anything useful anyway and that is still being written and under
control of TI. Ultimately we may have other libraries to do pulse
oximetry with these devices but we aren't aware of any yet.
- kernel-doc format fixes
- drop ifdef fun around of_match_ptr - it's not worth the mess to save
a tiny amount of space.
- drop some unnecessary register initializations.
- drop the weird locked gain modes as they gain us nothing (can just set
all gains separately).
- remove handling of offset attributes seeing as no channels actually have
them (oops)
- Drop the LED3 input channel as it's an alias for ALED2.
- *big one* remove channel names - an experiment that turned out to not
make sense - see patch for details.
- use regmap fields to clean up code.
- tie the tia gain stages to appropriate channels in the ABI as that is
what they really effect. Same with the LED currents.
- cleanout some unused defines and fix a missnamed one.
* atlas-ph
- reorganise to allow support of other similar parts.
* bmc150
- document supported chips in kconfig help.
* jsa1212
- drop an unneeded i2c functionality check for functionality the driver
doesn't use.
* mxs-lradc
- simply touch screen registration code.
- remove the touch screen unregister as all devm based now.
- disable only those channels that are masked in hardware stop (others
are already dealt with elsewhere)
* st-sensors
- unexport st_sensors_get_buffer_element as nothing outside the st-sensors
core driver uses it.
- fix handling of failure to start up regulators.
* tpl0102
- drop an i2c functionality test for features that aren't needed.
* ti-am335x
- use variable name rather than type in sizeof for clarity.
- use SIMPLE_DEV_PM_OPS helper macro to tidy up a bit.
Tools
* Add install / uninstall to makefile. Someone cares, so presumably
some people will find it useful!
* generic_buffer
- rename to iio_generic_buffer to line up with other tools.
- handle cleanup when receiving signals
- Add a --device-num option and a --trigger-num option rather than
relying on naming which doesn't work if you have two of the same part.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Hq1a
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.8a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.8 cycle.
New device support
* ads1015
- add ads1115 support
* bma220 accelerometer
- new driver
- triggered buffer support.
* bmc150
- add bmm150 support.
* bmp280
- bme280 support with addition of humidity channel.
* max5487 potentiometer
- new driver
* MMA7660FC accelerometer.
- New driver
* st-pressure
- support for the lps22hb
* loop trigger.
- This one is *nasty* but we have real applications (parrot drones) where
it is useful. The trigger basically spins as hard as it can firing off
a new trigger each time all triggered devices come back to say they are
done. It doesn't hang a machine even when doing it on a dummy driver.
A lot nicer than having this implemented within lots of device drivers
anyway.
Core stuff
* Add support to create IIO devices via configfs (similar to we did for
triggers a while back) + docs.
* New channel types
- IIO_ELECTRICAL_CONDUCTIVITY
* Couple of MAINTAINERS patches to list the device tree bindings.
* Make trigger ops structure non optional (comment fix). It hasn't been for
an awful long time, but that's not what the description said.
New features
* ak8975
- support adapters that are limited to byte data only by allowing the
emulated block read i2c function that was recently introduced.
* atlas-ph
- support atlas-ec (electrical conductivity sensor)
* bmi160
- add available frequency and scale attributes to make the driver
more user friendly (and avoid having to read the datasheet to know
what will work).
* dummy
- move creation to configfs interface. It's not real hardware so we
are not that worried about the ABI breakage ;)
* mma8452
- oversampling ration support
* nau7802
- expose available gains to make life easier for userspace.
* st-sensors
- allow use of emulation for SMBus block reads as all the st parts support
it.
* ti-ads1015
- list datasheet names to allow their use by inkernel consumers.
* Various module alias additions to help auto probing. Drop one redundant one
as well.
Cleanups
* ad7266, ad7476, ad7887, ad7923, ad799x
- use direct mode claim function rather than open coding it during sensor
read (prevents switching on buffers mid read).
* ad7793, ad7791
- use direct mode claim to prevent frequency changes when buffers running.
* afe440x - These are ABI breaking but the driver requires custom userspace
code to do anything useful anyway and that is still being written and under
control of TI. Ultimately we may have other libraries to do pulse
oximetry with these devices but we aren't aware of any yet.
- kernel-doc format fixes
- drop ifdef fun around of_match_ptr - it's not worth the mess to save
a tiny amount of space.
- drop some unnecessary register initializations.
- drop the weird locked gain modes as they gain us nothing (can just set
all gains separately).
- remove handling of offset attributes seeing as no channels actually have
them (oops)
- Drop the LED3 input channel as it's an alias for ALED2.
- *big one* remove channel names - an experiment that turned out to not
make sense - see patch for details.
- use regmap fields to clean up code.
- tie the tia gain stages to appropriate channels in the ABI as that is
what they really effect. Same with the LED currents.
- cleanout some unused defines and fix a missnamed one.
* atlas-ph
- reorganise to allow support of other similar parts.
* bmc150
- document supported chips in kconfig help.
* jsa1212
- drop an unneeded i2c functionality check for functionality the driver
doesn't use.
* mxs-lradc
- simply touch screen registration code.
- remove the touch screen unregister as all devm based now.
- disable only those channels that are masked in hardware stop (others
are already dealt with elsewhere)
* st-sensors
- unexport st_sensors_get_buffer_element as nothing outside the st-sensors
core driver uses it.
- fix handling of failure to start up regulators.
* tpl0102
- drop an i2c functionality test for features that aren't needed.
* ti-am335x
- use variable name rather than type in sizeof for clarity.
- use SIMPLE_DEV_PM_OPS helper macro to tidy up a bit.
Tools
* Add install / uninstall to makefile. Someone cares, so presumably
some people will find it useful!
* generic_buffer
- rename to iio_generic_buffer to line up with other tools.
- handle cleanup when receiving signals
- Add a --device-num option and a --trigger-num option rather than
relying on naming which doesn't work if you have two of the same part.
A slightly bumper set due to travel delaying the pull request and a fair few
issues with the recent merge window patches. Patches all over the place.
The st-sensors one is probably the most involved, but definitly solves the
issues seen. Note there are some other issues around that handler
(and the fact that a lot of boards tie a level interrupt chip to an
edge interrupt only irq chip). These are not regressions however, so
will turn up the slow route.
* core
- iio_trigger_attach_pollfunc had some really badly wrong error handling.
Another nasty triggered whilst chasing down issues with the st sensors
rework below.
* ad5592r
- fix an off by one error when allocating channels.
* am2315
- a stray mutex unlock before we ever take the lock.
* apds9960
- missing a parent in the driver model (which should be the i2c device).
Result is it doesn't turn up under /sys/bus/i2c/devices which some
userspace code uses for repeatable device identification.
* as3935
- ABI usage bug which meant a processed value was reported as raw. Now
reporting scale as well to ensure userspace has the info it needs.
- Don't return processed value via the buffer - it doesn't conform to
the ABI and will overflow in some cases.
- Fix a wrongly sized buffer which would overflow trashing part of the
stack. Also move it onto the heap as part of the fix.
* bh1780
- a missing return after write in debugfs lead to an incorrect read and
a null pointer dereference.
- dereferencing the wrong pointer in suspend and resume leading to
unpredictable results.
- assign a static name to avoid accidentally ending up with no name if
loaded via device tree.
* bmi160
- output data rate for the accelerometer was incorrectly reported. Fix it.
- writing the output data rate was also wrong due to reverse parameters.
* bmp280
- error message for wrong chip ID gave the wrong expected value.
* hdc100x
- mask for writing the integration time was wrong allowin g us to get
'stuck' in a particular value with no way back.
- temperature reported in celsius rather than millicelsius as per the
ABI.
- Get rid of some incorrect data shifting which lead to readings being
rather incorrect.
* max44000
- drop scale attribute for proximity as it is an unscaled value (depends
on what is in range rather than anything knowable at the detector).
* st-pressure
- ABI compliance fixes - units were wrong.
* st-sensors
- We introduced some nasty issues with the recent switch over to a
a somewhat threaded handler in that we broke using a software trigger
with these devices. Now do it properly. It's a larger patch than ideal
for a fix, but the logic is straight forward.
- Make sure the trigger is initialized before requesting the interrupt.
This matters now the interrupt can be shared. Before it was ugly and wrong
but short of flakey hardware could not be triggered.
- Hammer down the dataready pin at boot - otherwise with really
unlucky timing things could get interestingly wedged requiring a hard power
down of the chip.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=EEPO
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of iio fixes for the 4.7 cycle.
A slightly bumper set due to travel delaying the pull request and a fair few
issues with the recent merge window patches. Patches all over the place.
The st-sensors one is probably the most involved, but definitly solves the
issues seen. Note there are some other issues around that handler
(and the fact that a lot of boards tie a level interrupt chip to an
edge interrupt only irq chip). These are not regressions however, so
will turn up the slow route.
* core
- iio_trigger_attach_pollfunc had some really badly wrong error handling.
Another nasty triggered whilst chasing down issues with the st sensors
rework below.
* ad5592r
- fix an off by one error when allocating channels.
* am2315
- a stray mutex unlock before we ever take the lock.
* apds9960
- missing a parent in the driver model (which should be the i2c device).
Result is it doesn't turn up under /sys/bus/i2c/devices which some
userspace code uses for repeatable device identification.
* as3935
- ABI usage bug which meant a processed value was reported as raw. Now
reporting scale as well to ensure userspace has the info it needs.
- Don't return processed value via the buffer - it doesn't conform to
the ABI and will overflow in some cases.
- Fix a wrongly sized buffer which would overflow trashing part of the
stack. Also move it onto the heap as part of the fix.
* bh1780
- a missing return after write in debugfs lead to an incorrect read and
a null pointer dereference.
- dereferencing the wrong pointer in suspend and resume leading to
unpredictable results.
- assign a static name to avoid accidentally ending up with no name if
loaded via device tree.
* bmi160
- output data rate for the accelerometer was incorrectly reported. Fix it.
- writing the output data rate was also wrong due to reverse parameters.
* bmp280
- error message for wrong chip ID gave the wrong expected value.
* hdc100x
- mask for writing the integration time was wrong allowin g us to get
'stuck' in a particular value with no way back.
- temperature reported in celsius rather than millicelsius as per the
ABI.
- Get rid of some incorrect data shifting which lead to readings being
rather incorrect.
* max44000
- drop scale attribute for proximity as it is an unscaled value (depends
on what is in range rather than anything knowable at the detector).
* st-pressure
- ABI compliance fixes - units were wrong.
* st-sensors
- We introduced some nasty issues with the recent switch over to a
a somewhat threaded handler in that we broke using a software trigger
with these devices. Now do it properly. It's a larger patch than ideal
for a fix, but the logic is straight forward.
- Make sure the trigger is initialized before requesting the interrupt.
This matters now the interrupt can be shared. Before it was ugly and wrong
but short of flakey hardware could not be triggered.
- Hammer down the dataready pin at boot - otherwise with really
unlucky timing things could get interestingly wedged requiring a hard power
down of the chip.
