Commit 3e41a317ae ("PCI/AER: Remove unused aer_error_resume()")
removed the resume err_handler from AER. Since no other port service
implements the callback, support for it can be removed from portdrv.
It can be revived later if need be, preferably by re-using the
pcie_port_device_iter() iterator.
Link: https://lore.kernel.org/r/25334149b604e005058aeb0fdf51e01f991d5d74.1627638184.git.lukas@wunner.de
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Keith Busch <kbusch@kernel.org>
Stuart Hayes reports that an error handled by DPC at a Root Port results
in pciehp gratuitously bringing down a subordinate hotplug port:
RP -- UP -- DP -- UP -- DP (hotplug) -- EP
pciehp brings the slot down because the Link to the Endpoint goes down.
That is caused by a Hot Reset being propagated as a result of DPC.
Per PCIe Base Spec 5.0, section 6.6.1 "Conventional Reset":
For a Switch, the following must cause a hot reset to be sent on all
Downstream Ports: [...]
* The Data Link Layer of the Upstream Port reporting DL_Down status.
In Switches that support Link speeds greater than 5.0 GT/s, the
Upstream Port must direct the LTSSM of each Downstream Port to the
Hot Reset state, but not hold the LTSSMs in that state. This permits
each Downstream Port to begin Link training immediately after its
hot reset completes. This behavior is recommended for all Switches.
* Receiving a hot reset on the Upstream Port.
Once DPC recovers, pcie_do_recovery() walks down the hierarchy and
invokes pcie_portdrv_slot_reset() to restore each port's config space.
At that point, a hotplug interrupt is signaled per PCIe Base Spec r5.0,
section 6.7.3.4 "Software Notification of Hot-Plug Events":
If the Port is enabled for edge-triggered interrupt signaling using
MSI or MSI-X, an interrupt message must be sent every time the logical
AND of the following conditions transitions from FALSE to TRUE: [...]
* The Hot-Plug Interrupt Enable bit in the Slot Control register is
set to 1b.
* At least one hot-plug event status bit in the Slot Status register
and its associated enable bit in the Slot Control register are both
set to 1b.
Prevent pciehp from gratuitously bringing down the slot by clearing the
error-induced Data Link Layer State Changed event before restoring
config space. Afterwards, check whether the link has unexpectedly
failed to retrain and synthesize a DLLSC event if so.
Allow each pcie_port_service_driver (one of them being pciehp) to define
a slot_reset callback and re-use the existing pm_iter() function to
iterate over the callbacks.
Thereby, the Endpoint driver remains bound throughout error recovery and
may restore the device to working state.
Surprise removal during error recovery is detected through a Presence
Detect Changed event. The hotplug port is expected to not signal that
event as a result of a Hot Reset.
The issue isn't DPC-specific, it also occurs when an error is handled by
AER through aer_root_reset(). So while the issue was noticed only now,
it's been around since 2006 when AER support was first introduced.
[bhelgaas: drop PCI_ERROR_RECOVERY Kconfig, split pm_iter() rename to
preparatory patch]
Link: https://lore.kernel.org/linux-pci/08c046b0-c9f2-3489-eeef-7e7aca435bb9@gmail.com/
Fixes: 6c2b374d74 ("PCI-Express AER implemetation: AER core and aerdriver")
Link: https://lore.kernel.org/r/251f4edcc04c14f873ff1c967bc686169cd07d2d.1627638184.git.lukas@wunner.de
Reported-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.6.19+: ba952824e6: PCI/portdrv: Report reset for frozen channel
Cc: Keith Busch <kbusch@kernel.org>
The PCI error recovery always resets the link for a frozen state, so the
port driver should return that a reset is required for its result. This
will get the .slot_reset() callback invoked, which is necessary to
restore the port's config space. Without this, the driver had been
relying on downstream drivers to return this status.
Link: https://lore.kernel.org/r/20210104230300.1277180-6-kbusch@kernel.org
Tested-by: Hedi Berriche <hedi.berriche@hpe.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Hedi Berriche <hedi.berriche@hpe.com>
The PCIe Bandwidth Change Notification feature logs messages when the link
bandwidth changes. Some users have reported that these messages occur
often enough to significantly reduce NVMe performance. GPUs also seem to
generate these messages.
We don't know why the link bandwidth changes, but in the reported cases
there's no indication that it's caused by hardware failures.
Remove the bandwidth change notifications for now. Hopefully we can add
this back when we have a better understanding of why this happens and how
we can make the messages useful instead of overwhelming.
Link: https://lore.kernel.org/r/20200115221008.GA191037@google.com/
Link: https://lore.kernel.org/r/155605909349.3575.13433421148215616375.stgit@gimli.home/
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206197
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
A Root Complex Event Collector terminates error and PME messages from
associated RCiEPs.
Use the RCEC Endpoint Association Extended Capability to identify
associated RCiEPs. Link the associated RCiEPs as the RCECs are enumerated.
Co-developed-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Link: https://lore.kernel.org/r/20201121001036.8560-12-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of calling pci_pcie_type(dev) twice, call it once and save the
result. No functional change intended.
Link: https://lore.kernel.org/r/20201121001036.8560-7-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If a Root Complex Integrated Endpoint (RCiEP) is implemented, it may signal
errors through a Root Complex Event Collector (RCEC). Each RCiEP must be
associated with no more than one RCEC.
For an RCEC (which is technically not a Bridge), error messages "received"
from associated RCiEPs must be enabled for "transmission" in order to cause
a System Error via the Root Control register or (when the Advanced Error
Reporting Capability is present) reporting via the Root Error Command
register and logging in the Root Error Status register and Error Source
Identification register.
Given the commonality with Root Ports and the need to also support AER and
PME services for RCECs, extend the Root Port driver to support RCEC devices
by adding the RCEC Class ID to the driver structure.
Co-developed-by: Sean V Kelley <sean.v.kelley@intel.com>
Link: https://lore.kernel.org/r/20201121001036.8560-3-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
The method struct pci_error_handlers.error_detected() is defined and
documented as taking an 'enum pci_channel_state' for the second argument,
but most drivers use 'pci_channel_state_t' instead.
This 'pci_channel_state_t' is not a typedef for the enum but a typedef for
a bitwise type in order to have better/stricter typechecking.
Consolidate everything by using 'pci_channel_state_t' in the method's
definition, in the related helpers and in the drivers.
Enforce use of 'pci_channel_state_t' by replacing 'enum pci_channel_state'
with an anonymous 'enum'.
Note: Currently, from a typechecking point of view this patch changes
nothing because only the constants defined by the enum are bitwise, not the
enum itself (sparse doesn't have the notion of 'bitwise enum'). This may
change in some not too far future, hence the patch.
[bhelgaas: squash in
https://lore.kernel.org/r/20200702162651.49526-3-luc.vanoostenryck@gmail.comhttps://lore.kernel.org/r/20200702162651.49526-4-luc.vanoostenryck@gmail.com]
Link: https://lore.kernel.org/r/20200702162651.49526-2-luc.vanoostenryck@gmail.com
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename DPM_FLAG_NEVER_SKIP to DPM_FLAG_NO_DIRECT_COMPLETE which
matches its purpose more closely.
No functional impact.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # for PCI parts
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Prior to eed85ff4c0 ("PCI/DPC: Enable DPC only if AER is available"),
Linux handled DPC events regardless of whether firmware had granted it
ownership of AER or DPC, e.g., via _OSC.
PCIe r5.0, sec 6.2.10, recommends that the OS link control of DPC to
control of AER, so after eed85ff4c0, Linux handles DPC events only if it
has control of AER.
On platforms that do not grant OS control of AER via _OSC, Linux DPC
handling worked before eed85ff4c0 but not after.
To make Linux DPC handling work on those platforms the same way they did
before, add a "pcie_ports=dpc-native" kernel parameter that makes Linux
handle DPC events regardless of whether it has control of AER.
[bhelgaas: commit log, move pcie_ports_dpc_native to drivers/pci/]
Link: https://lore.kernel.org/r/20191023192205.97024-1-olof@lixom.net
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
A warning is generated when a PCIe device is probed with a degraded link,
but there was no similar mechanism to warn when the link becomes degraded
after probing. The Link Bandwidth Notification provides this mechanism.
Use the Link Bandwidth Management Interrupt to detect bandwidth changes,
and rescan the bandwidth, looking for the weakest point. This is the same
logic used in probe().
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
The Class Code for subtractive decode PCI-to-PCI bridge is 060401h; add an
entry to make portdrv support this type of bridge. This allows use of PCIe
services on subtractive decode ports.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[bhelgaas: add braces surrounding entry]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pci_device_id table was technically correct, but unusually formatted,
which made adding entries error-prone. Change the format so it's obvious
how to add entries.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When PCIe port is runtime suspended/resumed some extra steps might be
needed to be executed from the port service driver side. For instance we
may need to disable PCIe hotplug interrupt to prevent it from triggering
immediately when PCIe link to the downstream component goes down.
To make the above possible add optional ->runtime_suspend() and
->runtime_resume() callbacks to struct pcie_port_service_driver and call
them for each port service in runtime suspend/resume callbacks of portdrv.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: adjust "slot->state" for 5790a9c78e ("PCI: pciehp: Unify
controller and slot structs")]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently we try to keep PCIe ports runtime suspended over system suspend
if possible. This mostly happens when entering suspend-to-idle because
there is no need to re-configure wake settings.
This causes problems if the parent port goes into D3cold and it gets
resumed upon exit from system suspend. This may happen for example if the
port is part of PCIe switch and the same switch is connected to a PCIe
endpoint that needs to be resumed. The way exit from D3cold works according
PCIe 4.0 spec 5.3.1.4.2 is that power is restored and cold reset is
signaled. After this the device is in D0unitialized state keeping PME
context if it supports wake from D3cold.
The problem occurs when a PCIe hotplug port is left suspended and the
parent port goes into D3cold and back to D0: the port keeps its PME context
but since everything else is reset back to defaults (D0unitialized) it is
not set to detect hotplug events anymore.
For this reason change the PCIe portdrv power management logic so that it
is fine to keep the port runtime suspended over system suspend but it needs
to be resumed upon exit to make sure it gets properly re-initialized.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The port's config space may be cleared after a link reset, which wipes out
the bridge's bus and memory windows. Restore the config space that was
saved during probe so we can access downstream devices.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
The PCI port driver saves the PCI state after initializing the device with
the applicable service devices. This was, however, before the service
drivers were even registered because PCI probe happens before the
device_initcall initialized those service drivers. The config space state
that the services set up were not being saved. The end result would cause
PCI devices to not react to events that the drivers think they did if the
PCI state ever needed to be restored.
Fix this by changing the service drivers from using the init calls to
having the portdrv driver calling the services directly. This will get the
state saved as desired, while making the relationship between the port
driver and the services under it more explicit in the code.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Thunderbolt hotplug ports that were occupied before system sleep resume
with their downstream link in "off" state. Only after the Thunderbolt
controller has reestablished the PCIe tunnels does the link go up.
As a result, a spurious Presence Detect Changed and/or Data Link Layer
State Changed event occurs.
The events are not immediately acted upon because tunnel reestablishment
happens in the ->resume_noirq phase, when interrupts are still disabled.
Also, notification of events may initially be disabled in the Slot
Control register when coming out of system sleep and is reenabled in the
->resume_noirq phase through:
pci_pm_resume_noirq()
pci_pm_default_resume_early()
pci_restore_state()
pci_restore_pcie_state()
It is not guaranteed that the events are acted upon at all: PCIe r4.0,
sec 6.7.3.4 says that "a port may optionally send an MSI when there are
hot-plug events that occur while interrupt generation is disabled, and
interrupt generation is subsequently enabled." Note the "optionally".
If an MSI is sent, pciehp will gratuitously turn the slot off and back
on once the ->resume_early phase has commenced.
If an MSI is not sent, the extant, unacknowledged events in the Slot
Status register will prevent future notification of presence or link
changes.
Commit 13c65840fe ("PCI: pciehp: Clear Presence Detect and Data Link
Layer Status Changed on resume") fixed the latter by clearing the events
in the ->resume phase. Move this to the ->resume_noirq phase to also
fix the gratuitous disable/enablement of the slot.
The commit further restored the Slot Control register in the ->resume
phase, but that's dispensable because as shown above it's already been
done in the ->resume_noirq phase.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
The pci_error_handlers.slot_reset() callback is only used for non-bridge
devices (see broadcast_error_message()). Since portdrv only binds to
bridges, we don't need pcie_portdrv_slot_reset(), so remove it.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, remove pcie_portdrv_slot_reset() completely]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- move pcieport_if.h to drivers/pci/pcie/ to encapsulate it (Frederick
Lawler)
- merge pcieport_if.h into portdrv.h (Bjorn Helgaas)
- move workaround for BIOS PME issue from portdrv to PCI core (Bjorn
Helgaas)
- completely disable portdrv with "pcie_ports=compat" (Bjorn Helgaas)
- remove portdrv link order dependency (Bjorn Helgaas)
- remove support for unused VC portdrv service (Bjorn Helgaas)
- simplify portdrv feature permission checking (Bjorn Helgaas)
- remove "pcie_hp=nomsi" parameter (use "pci=nomsi" instead) (Bjorn
Helgaas)
- remove unnecessary "pcie_ports=auto" parameter (Bjorn Helgaas)
- use cached AER capability offset (Frederick Lawler)
- don't enable DPC if BIOS hasn't granted AER control (Mika Westerberg)
- rename pcie-dpc.c to dpc.c (Bjorn Helgaas)
* pci/portdrv:
PCI/DPC: Rename from pcie-dpc.c to dpc.c
PCI/DPC: Do not enable DPC if AER control is not allowed by the BIOS
PCI/AER: Use cached AER Capability offset
PCI/portdrv: Rename and reverse sense of pcie_ports_auto
PCI/portdrv: Encapsulate pcie_ports_auto inside the port driver
PCI/portdrv: Remove unnecessary "pcie_ports=auto" parameter
PCI/portdrv: Remove "pcie_hp=nomsi" kernel parameter
PCI/portdrv: Remove unnecessary include of <linux/pci-aspm.h>
PCI/portdrv: Simplify PCIe feature permission checking
PCI/portdrv: Remove unused PCIE_PORT_SERVICE_VC
PCI/portdrv: Remove pcie_port_bus_type link order dependency
PCI/portdrv: Disable port driver in compat mode
PCI/PM: Clear PCIe PME Status bit for Root Complex Event Collectors
PCI/PM: Clear PCIe PME Status bit in core, not PCIe port driver
PCI/PM: Move pcie_clear_root_pme_status() to core
PCI/portdrv: Merge pcieport_if.h into portdrv.h
PCI/portdrv: Move pcieport_if.h to drivers/pci/pcie/
Conflicts:
drivers/pci/pcie/Makefile
drivers/pci/pcie/portdrv.h
The platform may restrict the OS's use of PCIe services, e.g., via the ACPI
_OSC method. The user may use "pcie_ports=native" to force the port driver
to use PCIe services even if the platform asked us not to.
The "pcie_ports=native" parameter determines the setting of
pcie_ports_auto. Rename this to pcie_ports_native and reverse the
sense to simplify the code.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "pcie_ports=auto" parameter set pcie_ports_disabled and pcie_ports_auto
to their compiled-in defaults, so specifying the parameter is the same as
not using it at all.
Remove the "pcie_ports=auto" parameter and update the documentation.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
portdrv_pci.c doesn't use anything from <linux/pci-aspm.h>. Remove the
include of it. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The pcie_port_bus_type must be registered before drivers that depend on it
can be registered. Those drivers include:
pcied_init() # PCIe native hotplug driver
aer_service_init() # AER driver
dpc_service_init() # DPC driver
pcie_pme_service_init() # PME driver
Previously we registered pcie_port_bus_type from pcie_portdrv_init(), a
device_initcall. The callers of pcie_port_service_register() (above) are
also device_initcalls. This is fragile because the device_initcall
ordering depends on link order, which is not explicit.
Register pcie_port_bus_type from pci_driver_init() along with pci_bus_type.
This removes the link order dependency between portdrv and the pciehp, AER,
DPC, and PCIe PME drivers.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The "pcie_ports=compat" kernel parameter sets pcie_ports_disabled, which is
intended to disable the PCIe port driver. But even when it was disabled,
we registered pcie_portdriver so we could work around a BIOS PME issue (see
fe31e69740 ("PCI/PCIe: Clear Root PME Status bits early during system
resume")).
Registering the driver meant that the pcie_portdrv_probe() path called
pci_enable_device(), pci_save_state(), pm_runtime_set_autosuspend_delay(),
pm_runtime_use_autosuspend(), etc., even when the driver was disabled.
We've since moved the BIOS PME workaround from the port driver to the core,
so stop registering the PCIe port driver in compat mode.
This means "pcie_ports=compat" will now be basically the same as turning
off CONFIG_PCIEPORTBUS completely.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove pointless comments that tell us the file name, remove blank line
comments, follow multi-line comment conventions. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
fe31e69740 ("PCI/PCIe: Clear Root PME Status bits early during system
resume") added a .resume_noirq() callback to the PCIe port driver to clear
the PME Status bit during resume to work around a BIOS issue.
The BIOS evidently enabled PME interrupts for ACPI-based runtime wakeups
but did not clear the PME Status bit during resume, which meant PMEs after
resume did not trigger interrupts because PME Status did not transition
from cleared to set.
The fix was in the PCIe port driver, so it worked when CONFIG_PCIEPORTBUS
was set. But I think we *always* want the fix because the platform may use
PME interrupts even if Linux is built without the PCIe port driver.
Move the fix from the port driver to the PCI core so we can work around
this "PME doesn't work after waking from a sleep state" issue regardless of
CONFIG_PCIEPORTBUS.
[bhelgaas: folded in warning fix from Arnd Bergmann <arnd@arndb.de>:
https://lkml.kernel.org/r/20180328134747.2062348-1-arnd@arndb.de]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move pcie_clear_root_pme_status() from the port driver to the PCI core so
it will be available even when the port driver isn't present. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
pcieport_if.h contained the interfaces to register port service driver,
e.g., pcie_port_service_register(). portdrv.h contained internal data
structures of the port driver.
I don't think it's worth keeping those files separate, since both headers
and their users are all inside the PCI core.
Merge pcieport_if.h directly in drivers/pci/pcie/portdrv.h and update the
users to include that instead.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Move pcieport_if.h from include/linux to drivers/pci/pcie/pcieport_if.h
because the interfaces there are only used by the PCI core.
Replace all uses of #include<linux/pcieport_if.h> with relative paths to
the new file location, e.g., #include "../pcieport_if.h"
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Make the PCIe port driver set DPM_FLAG_SMART_SUSPEND and
DPM_FLAG_LEAVE_SUSPENDED for the devices handled by it to benefit
from the opportunistic optimizations in the PCI layer enabled by
these flags.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Some of the PCIe services such as AER are being left enabled during
shutdown. This might cause spurious AER errors while SOC is being powered
down.
Clean up the PCIe services gracefully during shutdown to clear these false
positives.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Move the error handler methods to struct pcie_port_service_driver and avoid
the detour through the mostly unused pci_error_handlers structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The conditions to allow runtime PM on PCIe ports are currently spread
across two different files: The condition relating to hotplug ports is
located in portdrv_pci.c whereas all other conditions are located in pci.c.
Consolidate all conditions in a single place in pci.c, thus making it
easier to follow the logic and amend conditions down the road.
Note that the condition relating to hotplug ports is inserted *before* the
condition relating to the "pcie_port_pm=force" command line option, so
runtime PM is not afforded to hotplug ports even if this option is given.
That's exactly how the code behaved up until now. If this is not desired,
the ordering of the conditions can simply be reversed.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently pcie_portdrv_probe() activates runtime PM on a PCIe port even
if it will never actually suspend because the BIOS is too old or the
"pcie_port_pm=off" option was specified on the kernel command line.
A few CPU cycles can be saved by not activating runtime PM at all in these
cases, because rpm_idle() and rpm_suspend() will bail out right at the
beginning when calling rpm_check_suspend_allowed(), instead of carrying out
various locking and assignments, invoking rpm_callback(), getting back
-EBUSY and rolling everything back.
The conditions checked in pci_bridge_d3_possible() are all static, they
never change during uptime of the system, hence it's safe to call this to
determine if runtime PM should be activated.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This code is not being built as a module by anyone:
pcieportdrv-y := portdrv_core.o portdrv_pci.o portdrv_bus.o
obj-$(CONFIG_PCIEPORTBUS) += pcieportdrv.o
drivers/pci/pcie/Kconfig:config PCIEPORTBUS
drivers/pci/pcie/Kconfig: bool "PCI Express Port Bus support"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Note that for non-modular code, MODULE_DEVICE_TABLE is a no-op and
module_init() translates to device_initcall().
[bhelgaas: changelog, remove unused DRIVER_* macros]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Tom Long Nguyen <tom.l.nguyen@intel.com>
Add back runtime PM support for PCIe ports that was removed by
fe9a743a26 ("PCI/PM: Drop unused runtime PM support code for PCIe
ports").
We cannot enable it automatically for all ports since there have been
problems previously [1]. In summary suspended PCIe ports were not able
to deal with ACPI-based hotplug reliably. One reason why this might happen
is the fact that when a PCIe port is powered down, config space access to
the devices behind the port is not possible. If the BIOS hotplug SMI
handler assumes the port is always in D0 it will not be able to find the
hotplugged devices. To be on the safe side only enable runtime PM if the
port does not claim to support hotplug.
For PCIe ports not using hotplug, we enable and allow runtime PM
automatically. Since 'bridge_d3' can be changed any time we check this in
driver ->runtime_idle() and ->runtime_suspend() and only allow runtime
suspend if the flag is still set. Use autosuspend with default of 100ms
idle time to prevent the port from repeatedly suspending and resuming on
continuous configuration space access of devices behind the port.
The actual power transition to D3 and back is handled in the PCI core.
Idea to automatically unblock (allow) runtime PM for PCIe ports came from
Dave Airlie.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=53811
This includes a fix for lockdep issue reported by Valdis Kletnieks.
Tested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PCI core skips bridges and ports when the system is suspended. The PCI
core checks return value of pci_has_subordinate() in pci_pm_suspend_noirq()
to skip all devices where it is non-zero (which means PCI bridges and PCIe
ports).
Since PCIe ports are never suspended in the first place, there is no need
to set d3cold_allowed for them.
Tested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since commit de7d5f729c ("PCI/PM: Disable runtime PM of PCIe ports") the
runtime PM support code for PCIe ports in portdrv_pci.c has never been
used, so drop it entirely.
If we are to support runtime PM of PCIe ports, it will have to be done in a
different way most likely anyway.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
For hot-added PCIe ports on x86 platforms, we always warned about an
invalid IRQ, e.g.,
pci 0000:00:00.0: device [8086:0e0b] has invalid IRQ; check vendor BIOS
This was because we check pci_dev->irq before actually allocating the IRQ
for the device, which happens in this path:
pcie_port_device_register
pci_enable_device
pci_enable_device_flags
do_pci_enable_device
pcibios_enable_device (on x86)
pcibios_enable_irq
This warning message isn't generated for PCIe ports present at boot time
because x86 arch code has called acpi_pci_irq_enable() in pci_acpi_init()
for each PCI device for safety.
[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Merge quoted strings that are broken across lines into a single entity.
The compiler merges them anyway, but checkpatch complains about it, and
merging them makes it easier to grep for strings.
No functional change.
[bhelgaas: changelog, do the same for everything under drivers/pci]
Signed-off-by: Ryan Desfosses <ryan@desfo.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pcie_portdrv .probe() method calls pci_enable_device() once, in
pcie_port_device_register(), but the .remove() method calls
pci_disable_device() twice, in pcie_port_device_remove() and in
pcie_portdrv_remove().
That causes a "disabling already-disabled device" warning when removing a
PCIe port device. This happens all the time when removing Thunderbolt
devices, but is also easy to reproduce with, e.g.,
"echo 0000:00:1c.3 > /sys/bus/pci/drivers/pcieport/unbind"
This patch removes the disable from pcie_portdrv_remove().
[bhelgaas: changelog, tag for stable]
Reported-by: David Bulkow <David.Bulkow@stratus.com>
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v2.6.32+
Fix whitespace, capitalization, and spelling errors. No functional change.
I know "busses" is not an error, but "buses" was more common, so I used it
consistently.
Signed-off-by: Marta Rybczynska <rybczynska@gmail.com> (pci_reset_bridge_secondary_bus())
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
