We're saving some extra memory now by being a lot
more conservative when allocating our event buffers.
Our default HIRD threshold value was mistakenly set
as one of the unsupported which would cause undefined
behavior. Turns out that it broke OMAP5 ES2.0, so we're
fixing it now by setting the maximum allowed HIRD
threshold (12).
Quite a few fixes to Isochronous transfers and scatter/gather
support from Pratyush.
We're also starting to support devicetree-based probe with
the latest changes from Kishon.
The usual set of cleanups also available: converting debugfs
regdump utility to regsets, better "compatible" strings for
Exynos platforms and the removal of the dependency for
Host and Gadget; now dwc3 can be compiled host-only, device-only,
and/or Dual-Role.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JJ6/
-----END PGP SIGNATURE-----
Merge tag 'dwc3-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: dwc3: patches for v3.9 merge window
We're saving some extra memory now by being a lot
more conservative when allocating our event buffers.
Our default HIRD threshold value was mistakenly set
as one of the unsupported which would cause undefined
behavior. Turns out that it broke OMAP5 ES2.0, so we're
fixing it now by setting the maximum allowed HIRD
threshold (12).
Quite a few fixes to Isochronous transfers and scatter/gather
support from Pratyush.
We're also starting to support devicetree-based probe with
the latest changes from Kishon.
The usual set of cleanups also available: converting debugfs
regdump utility to regsets, better "compatible" strings for
Exynos platforms and the removal of the dependency for
Host and Gadget; now dwc3 can be compiled host-only, device-only,
and/or Dual-Role.
Mostly fixes all over which weren't urgent enough for
the late -rc cycle.
There is a Double Buffering fix for Host Mode TX,
a dependency fix for the transceiver driver, some
fixes to the error path and a fix for the use of
omap_musb_maibox.
Other than these fixes, there a removal duplicate
headers from the dsps glue layer and removal of
redundant assignments in omap2430_probe().
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=dDY3
-----END PGP SIGNATURE-----
Merge tag 'musb-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: musb: patches for v3.9 merge window
Mostly fixes all over which weren't urgent enough for
the late -rc cycle.
There is a Double Buffering fix for Host Mode TX,
a dependency fix for the transceiver driver, some
fixes to the error path and a fix for the use of
omap_musb_maibox.
Other than these fixes, there a removal duplicate
headers from the dsps glue layer and removal of
redundant assignments in omap2430_probe().
Multiple dwc3 controllers will try to allocate multiple xhci-hcd
interfaces.
Changing platform device IDs from NONE to AUTO to support
such cases.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Multiple dwc3 probe calls try to allocate no_op_xceive platform
device. Having static IDs for these will throw sysfs error -EEXIST.
Changing these static platform device IDs to AUTO to enable
multiple dwc3 controller support on a SoC.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added dt support for dwc3 core and update the documentation with
device tree binding information. Getting a PHY is now done using
devm_usb_get_phy_by_phandle() for dt boot.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
"usb_otg_ss_refclk960m" is needed for usb2 phy present in omap5. For
omap4, the clk_get of this clock will fail since it does not have this
clock.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The OMAP glue has been modified to get PHY by phandle
for dt boot.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
New PHY lib APIs like usb_add_phy_dev() and devm_usb_get_phy_dev() are
used in MUSB (OMAP), in order to make use of the binding information
provided in the board file (of OMAP platforms).
All the platforms should be modified similar to this to add and get the
PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added a driver for usb3 phy that handles the interaction between usb phy
device and dwc3 controller.
This also includes device tree support for usb3 phy driver and
the documentation with device tree binding information is updated.
Currently writing to control module register is taken care in this
driver which will be removed once the control module driver is in place.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Start using the control module driver for powering on the PHY and for
writing to the mailbox instead of writing to the control module
registers on their own.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added a new driver for the usb part of control module. This has an API
to power on the USB2 phy and an API to write to the mailbox depending on
whether MUSB has to act in host mode or in device mode.
Writing to control module registers for doing the above task which was
previously done in omap glue and in omap-usb2 phy will be removed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added an API devm_usb_get_phy_by_phandle(), to get usb phy by passing a
device node phandle value. This function will return a pointer to
the phy on success, -EPROBE_DEFER if there is a device_node for the phandle,
but the phy has not been added, or a ERR_PTR() otherwise.
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In order to add support for multipe PHY's of the same type, new API's
for adding PHY and getting PHY has been added. Now the binding
information for the PHY and controller should be done in platform file
using usb_bind_phy API. And for getting a PHY, the device pointer of the
USB controller and an index should be passed. Based on the binding
information that is added in the platform file, usb_get_phy_dev will return the
appropriate PHY.
Already existing API's to add and get phy by type is not removed. These
API's are deprecated and will be removed once all the platforms start to
use the new API.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In order to support platforms which has multiple PHY's (of same type) and
which has multiple USB controllers, a new design is adopted wherin the binding
information (between the PHY and the USB controller) should be passed to the
PHY library from platform specific file (board file).
So added a new API to pass the binding information.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
No functional change. Stray statements where removed from dwc3 core.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Enabled the USB2 and USB3 PHY in probe by calling usb_phy_set_suspend
and disabled the PHYs on driver removal. When PM is implemented this
will be optimized to enable the PHYs only when needed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add an API in the omap glue layer to write to the mailbox register which
can be used by comparator driver(twl). To pass the detection of the attached
device (signified by VBUS, ID) to the dwc3 core, dwc3 core has to write
to the mailbox regiter.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The runtime API's takes care of setting the SYSCONFIG register with
appropriate values. Hence explicit writes to SYSCONFIG register is
removed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Before accessing any register, runtime API's should be invoked to enable
the clocks. runtime API's are added here to prevent abort during register
access.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Used of_platform_populate() to create dwc3 core platform_device
from device tree data.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Used device_for_each_child() to handle child device (dwc3 core) removal
during devexit of dwc3 omap. This is in preparation for creating the child
devices from subnode of dwc3 omap glue using of_platform_populate.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using specific chip in compatible strings. Newer SOCs can claim
device by using older string in the compatible list.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using specific chip in compatible strings. Newer SOCs can claim
device by using older string in the compatible list.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1646) fixes a long-standing bug in the USB hub driver.
Upon conversion from char to unsigned long, the bytes in the status
buffer are subject to unwanted sign extension. The bytes should be
declared as u8 rather than char, to prevent this.
This effects of this bug are minimal. The hub driver may end up doing
a little unnecessary extra work because it thinks events have occurred
on some ports when they really haven't.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get rid of the line breaks in string constants.
let comments within 80 with limitation.
delete ' \' at the end of a statement.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding three currently unsupported modems based on information
from .inf driver files:
Diag VID_1BBB&PID_0052&MI_00
AGPS VID_1BBB&PID_0052&MI_01
VOICE VID_1BBB&PID_0052&MI_02
AT VID_1BBB&PID_0052&MI_03
Modem VID_1BBB&PID_0052&MI_05
wwan VID_1BBB&PID_0052&MI_06
Diag VID_1BBB&PID_00B6&MI_00
AT VID_1BBB&PID_00B6&MI_01
Modem VID_1BBB&PID_00B6&MI_02
wwan VID_1BBB&PID_00B6&MI_03
Diag VID_1BBB&PID_00B7&MI_00
AGPS VID_1BBB&PID_00B7&MI_01
VOICE VID_1BBB&PID_00B7&MI_02
AT VID_1BBB&PID_00B7&MI_03
Modem VID_1BBB&PID_00B7&MI_04
wwan VID_1BBB&PID_00B7&MI_05
Updating the blacklist info for the X060S_X200 and X220_X500D,
reserving interfaces for a wwan driver, based on
wwan VID_1BBB&PID_0000&MI_04
wwan VID_1BBB&PID_0017&MI_06
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added device tree support for usb3503 driver and add new document with device tree binding information.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
for function uhci_sprint_schedule:
the buffer len is MAX_OUTPUT: 64 * 1024, which may not be enough:
may loop UHCI_NUMFRAMES times (UHCI_NUMFRAMES is 1024)
each time of loop may get more than 64 bytes
so need check the buffer length to avoid memory overflow
this patch fix it like this:
at first, make enough room for buffering the exceeding contents
judge the contents which written whether bigger than buffer length
if bigger (the exceeding contents will be in the exceeding buffer)
break current work flow, and return.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usally we will use udc->tranceiver == NULL or
udc->tranceiver != NULL.
So when failed to get the udc->tranceiver by usb_get_phy(), we
directly set udc->tranceiver to be NULL.
Then the source code will not need macro IS_ERR_OR_NULL() for
udc->tranceiver judgement. It can reduce the line size and make
the judgement simple.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
use devm_xxx for otg driver probe. So we do need care about
the resources release in driver remove or failure handling
in driver probe.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The __exit_p() will be NULL if MODULE is no defined.
It will cause the warning. Removing __exit_p to remove
the warning.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
use devm_xxx for udc driver probe. So we do need care about
the resources release in driver remove or failure handling
in driver probe.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Those have been deprecated for a long time and
previous patches just converted all remaining
users of those.
Since there are no in-tree users and we don't
want any new users for them, let's obliterate
every piece of code related to those calls.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Usb3.0 device defines function remote wakeup which is only for interface
recipient rather than device recipient. This is different with usb2.0 device's
remote wakeup feature which is defined for device recipient. According usb3.0
spec 9.4.5, the function remote wakeup can be modified by the SetFeature()
requests using the FUNCTION_SUSPEND feature selector. This patch is to use
correct way to disable usb3.0 device's function remote wakeup after suspend
error and resuming.
This should be backported to kernels as old as 3.4, that contain the
commit 623bef9e03 "USB/xhci: Enable remote
wakeup for USB3 devices."
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
When the xHCI driver is not available, actively switch the ports to EHCI
mode since some BIOSes leave them in xHCI mode where they would
otherwise appear dead. This was discovered on a Dell Optiplex 7010,
but it's possible other systems could be affected.
This should be backported to kernels as old as 3.0, that contain the
commit 69e848c209 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: David Moore <david.moore@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
This patch (as1640) fixes a memory leak in xhci-hcd. The urb_priv
data structure isn't always deallocated in the handle_tx_event()
routine for non-control transfers. The patch adds a kfree() call so
that all paths end up freeing the memory properly.
This patch should be backported to kernels as old as 2.6.36, that
contain the commit 8e51adccd4 "USB: xHCI:
Introduce urb_priv structure"
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-and-tested-by: Martin Mokrejs <mmokrejs@fold.natur.cuni.cz>
CC: <stable@vger.kernel.org>
Fix incorrect bit test that originally showed up in
4ee823b83b "USB/xHCI: Support
device-initiated USB 3.0 resume."
Use '&' instead of '&&'.
This should be backported to kernels as old as 3.4.
Signed-off-by: Nickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
To calculate the TD size for a particular TRB in an isoc TD, we need
know the endpoint's max packet size. Isochronous endpoints also encode
the number of additional service opportunities in their wMaxPacketSize
field. The TD size calculation did not mask off those bits before using
the field. This resulted in incorrect TD size information for
isochronous TRBs when an URB frame buffer crossed a 64KB boundary.
For example:
- an isoc endpoint has 2 additional service opportunites and
a max packet size of 1020 bytes
- a frame transfer buffer contains 3060 bytes
- one frame buffer crosses a 64KB boundary, and must be split into
one 1276 byte TRB, and one 1784 byte TRB.
The TD size is is the number of packets that remain to be transferred
for a TD after processing all the max packet sized packets in the
current TRB and all previous TRBs.
For this TD, the number of packets to be transferred is (3060 / 1020),
or 3. The first TRB contains 1276 bytes, which means it contains one
full packet, and a 256 byte remainder. After processing all the max
packet-sized packets in the first TRB, the host will have 2 packets left
to transfer.
The old code would calculate the TD size for the first TRB as:
total packet count = DIV_ROUND_UP (TD length / endpoint wMaxPacketSize)
total packet count - (first TRB length / endpoint wMaxPacketSize)
The math should have been:
total packet count = DIV_ROUND_UP (3060 / 1020) = 3
3 - (1276 / 1020) = 2
Since the old code didn't mask off the additional service interval bits
from the wMaxPacketSize field, the math ended up as
total packet count = DIV_ROUND_UP (3060 / 5116) = 1
1 - (1276 / 5116) = 1
Fix this by masking off the number of additional service opportunities
in the wMaxPacketSize field.
This patch should be backported to stable kernels as old as 3.0, that
contain the commit 4da6e6f247 "xhci 1.0:
Update TD size field format." It may not apply well to kernels older
than 3.2 because of commit 29cc88979a
"USB: use usb_endpoint_maxp() instead of le16_to_cpu()".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
An isochronous TD is comprised of one isochronous TRB chained to zero or
more normal TRBs. Only the isoc TRB has the TBC and TLBPC fields. The
normal TRBs must set those fields to zeroes. The code was setting the
TBC and TLBPC fields for both isoc and normal TRBs. Fix this.
This should be backported to stable kernels as old as 3.0, that contain
the commit b61d378f2d " xhci 1.0: Set
transfer burst last packet count field."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
First of all, that 28 value makes no sense as
HIRD threshold is a 4-bit value, second of all
it's causing issues for OMAP5.
Using 12 because commit cbc725b3 (usb: dwc3:
keep default hird threshold value as 4b1100)
had the intention of setting the maximum allowed
value of 0xc.
Also, original code has been wrong forever, so
this should be backported as far back as
possible.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patches converts the driver into the new style start/stop
interface. As a result the driver no longer uses the static
global the_conroller variable.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch (as1643b) fixes a build error in ehci-hcd when compiling for
ARM with allmodconfig:
drivers/usb/host/ehci-hcd.c:1285:0: warning: "PLATFORM_DRIVER" redefined [enabled by default]
drivers/usb/host/ehci-hcd.c:1255:0: note: this is the location of the previous definition
drivers/usb/host/ehci-mxc.c:280:31: warning: 'ehci_mxc_driver' defined but not used [-Wunused-variable]
drivers/usb/host/ehci-hcd.c:1285:0: warning: "PLATFORM_DRIVER" redefined [enabled by default]
drivers/usb/host/ehci-hcd.c:1255:0: note: this is the location of the previous definition
The fix is to convert ehci-mxc over to the new "ehci-hcd is a library"
scheme so that it can coexist peacefully with the ehci-platform
driver. As part of the conversion the ehci_mxc_priv data structure,
which was allocated dynamically, is now placed where it belongs: in
the private area at the end of struct ehci_hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dropping __devinit, __devexit_p, __exit annotations since they are
nop and no longer supported.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adding the phy-driver to ohci-exynos. Keeping the platform data
for continuing the smooth operation for boards which still uses it
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adding the phy driver to ehci-s5p. Keeping the platform data
for continuing the smooth operation for boards which still uses it
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds host phy support to samsung-usbphy driver and
further adds support for samsung's exynos5250 usb-phy.
Signed-off-by: Praveen Paneri <p.paneri@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Updating the names of usb-phy types to more generic names:
USB_PHY_TYPE_DEIVCE & USB_PHY_TYPE_HOST; and further update
its dependencies.
Signed-off-by: Praveen Paneri <p.paneri@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1642) adds an ehci->priv field for private use by EHCI
platform drivers. The space was provided some time ago, but it didn't
have a name.
Until now none of the platform drivers has used this private space,
but that's about to change in the next patch of this series.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1641) fixes a minor bug in ehci-hcd left over from when
the Chipidea driver was converted to the "ehci-hcd is a library"
scheme. The test for whether the Chipidea platform driver is active
should be IS_ENABLED(), not defined().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this, platform drivers e.g. ehci-omap.c will see a
different version of struct ehci_hcd than ehci-hcd.c and
break reference to 'debug_dir' and 'priv' members when
CONFIG_USB_DEBUG is enabled.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1644) fixes a race that occurs during startup in
uhci-hcd. If the IRQ line is shared with other devices, it's possible
for the handler routine to be called before the data structures are
fully initialized.
The problem is fixed by adding a check to the IRQ handler routine. If
the initialization hasn't finished yet, the routine will return
immediately.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Don Zickus <dzickus@redhat.com>
Tested-by: "Huang, Adrian (ISS Linux TW)" <adrian.huang@hp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI provide "_PLD" and "_UPC" aml methods to describe usb port
visibility and connectability. This patch is to add usb_hub_adjust_DeviceRemovable()
to adjust usb hub port's DeviceRemovable according ACPI information and invoke it in
the rh_call_control(). When hub descriptor request is issued at first time,
usb port device isn't created and usb port is not bound with acpi. So first
hub descriptor request is not changed based on ACPI information. After usb
port devices being created, call usb_hub_adjust_DeviceRemovable in the hub_configure()
and then set hub port's DeviceRemovable according ACPI information and this also works
for non-root hub.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Delete successive tests to the same location. In this case res has already
been tested for being NULL, and calling devm_request_and_ioremap will not
make it NULL. On the other hand, devm_request_and_ioremap can return NULL
on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@s exists@
local idexpression y;
expression x,e;
@@
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\)
when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\)
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Finally we have a build fix for fsl-mxc-udc UDC driver.
We also have a fix for ep0 maxburst setting on DWC3
which could confuse the HW if we tell it we had way
too many streams on that endpoint when it _has_ to be
only one.
cppi_dma support for MUSB got a fix when running as a
module. By dropping the wrong __init annotation, the
function will be available even when we're modules and
we're done with .init.text section.
Last, but not least, we have a fix on FunctionFS which
was causing a bug on our option parsing algorithm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=4n68
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.8-rc5
Finally we have a build fix for fsl-mxc-udc UDC driver.
We also have a fix for ep0 maxburst setting on DWC3
which could confuse the HW if we tell it we had way
too many streams on that endpoint when it _has_ to be
only one.
cppi_dma support for MUSB got a fix when running as a
module. By dropping the wrong __init annotation, the
function will be available even when we're modules and
we're done with .init.text section.
Last, but not least, we have a fix on FunctionFS which
was causing a bug on our option parsing algorithm.
drivers/usb/gadget/u_serial.c:1291:5: sparse: symbol \
'userial_init' was not declared. Should it be static?
drivers/usb/gadget/zero.c:66:25: sparse: symbol \
'gzero_options' was not declared. Should it be static?
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use usb_gstrings_attach() to assign strings in f_acm to assign strings
ids.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The USB strings don't (yet) fully work in multiple configs/gadget
environment. The string id is assigned to the descriptor and the struct
usb_strings. We create a copy of the individual descriptor so we don't
clash if we use a function more than once. However, we have only one
struct usb_string for each string.
Currently each function which is used multiple times checks for
"id != 0" and only assigns string ids if it did not happen yet. This
works well if we use the same function multiple times as long as we do
it within the "one" gadget we have. Trouble starts once we use the same
function in a second gadget.
In order to solve this I introduce usb_gstrings_attach(). This function will
crate a copy all structs except for the strings which are not copied.
After the copy it will assign USB ids and attach it to cdev.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The configfs can't use all of composite's hooks because ->bind() and
->unbind() has to be done a little differently. ->disconnect() and
->setup() on the hand can be recycled.
This patch exports them both so configfs can use them.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch factors out two helper functions from composite_bind()
that is composite_dev_prepare() and its counterpart
composite_dev_cleanup().
This will be used by the configfs which requries a slightly different
bind/setup code because part of its configurations (i.e. config
descripts, cdev, …) are setup in advance and VID/PID and so one should
not be overwritten. Also the setup of ep0 endpoint can be delayed until
the UDC is assigned.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds udc_attach_driver() which allows to bind an UDC which is
specified by name to a driver. The name of available UDCs can be
obtained from /sys/class/udc. This interface is intended for configfs
interface.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We can have multiple usb_functions which origin is the same "instance".
Within one USB configuration there should be only one function of an
instance. This back pointer helps configfs to recoginze to which
instance a given usb_function belongs.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch converts the acm_ms gadget to make use of the function
framework to request the ACM function.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch converts the acm_ms gadget to make use of the function
framework to request the ACM function.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch converts the acm_ms gadget to make use of the function
framework to request the ACM function.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch converts f_acm into a module which uses the new function
interface. It also converts one of its users that is g_serial to make
use of it. The other users of it (g_nokia for instance) are still using
the old include file system and should not notice the change at all. So
they can be converter later independently.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes gserial_setup() and gserial_cleanup() and adds
gserial_alloc_line() and gserial_free_line() to replace them.
The initial setup of u_serial happens now on module load time. A
maximum of four TTY ports can be requested which is the current limit.
In theory we could extend this limit, the hard limit is the number of
available endpoints.
alloc_tty_driver() is now called at module init time with the max
available ports. The per-line footprint here is on 32bit is 3 * size of
pointer + 60 bytes (for cdevs).
The remaining memory (struct gs_port) is allocated once a port is
requested.
With this change it is possible to load g_multi and g_serial at the same
time. GS0 receives the module that is loaded first, GS1 is received by
the next module and so on. With the configfs interface the port number
can be exported and the device node is more predictable. Nothing changes
for g_serial and friends as long as one module is used.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This will be used to remove a single function from a given config. Right
now "ignore" that an error at ->bind() time and cleanup later during
composite_unbind() / remove_config().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Every user of u_serial has now to select the U_SERIAL symbol instead of
including the file.
There is one limition with this: ports and and gs_tty_driver are global
variables in u_serial. Since all users share them, there can be only one
user loaded at a time i.e. either g_serial or g_nokia.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch factors out the three possible functions into three possible
bind functions which are passed as an argument to usb_add_config(). This
will ease the step by step converting of the individual functions to the
new function registration method.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The significant part of this function was removed in 90f7976 ("USB:
Remove unsupported usb gadget drivers"). I would move this to function
bind time but I don't see the point in moving an empty function.
Therefore bye bye.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch converts the f_sourcesink and f_loopback file to the USB-function
module. Both functions shares a few common utility functions which are
currently implemented in g_zero.c itself. This patch moves the common
code into the sourcesink file and creates one module out of the the two
functions (source sink and loop back).
The g_zero gadget is function specific to source sink and loop back to
set a few options. This Symbol dependency enforces a modul load right
now.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch provides an infrastructure to register & unregister a USB
function. This allows to turn a function into a module and avoid the
'#include "f_.*.c"' magic and we get a clear API / cut between the bare
gadget and its functions.
The concept is simple:
Each function defines the DECLARE_USB_FUNCTION_INIT macro whith an unique
name of the function and two allocation functions.
- one to create an "instance". The instance holds the current configuration
set. In case there are two usb_configudations with one function there will
be one instance and two usb_functions
- one to create an "function" from the instance.
The name of the instance is used to automaticaly load the module if it the
instance is not yet available.
The usb_function callbacks are slightly modified and extended:
- usb_get_function()
creates a struct usb_function inclunding all pointers (bind,
unbind,…). It uses the "instance" to map its configuration. So we can
have _two_ struct usb_function, one for each usb_configuration.
- ->unbind()
Since the struct usb_function was not allocated in ->bind() it should
not kfree()d here. This function should only reverse what happens in
->bind() that is request cleanup and the cleanup of allocated
descriptors.
- ->free_func()
a simple kfree() of the struct usb_function
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
f_loopback should only include the bare function but it also includes
the config descriptor. This patch moves the config descriptor into
zero.c, the only user of this function.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
f_sourcesink should only include the bare function but it also includes
the config descriptor. This patch moves the config descriptor into
zero.c, the only user of this function.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The setup request can be sent to an interface/endpoint or to the device
itself. If it is sent to an interface / endpoint then we forward it to
the function that is mapped to that interface / endpoint.
If the device is the target of the setup request then we forward it to the
->setup() callback of the currently active configuration.
In case of the sourcesink function the requests are function specific
but are sent to the device.
This patch introduces a setup wrapper at configuration level which
forwards the request to the function. By using this wrapper we can keep
the function specific code within the function file and we need just a
hint at config level to forward the request.
The here introduced global variable will be moved into the gadget (which
combines the two functions) in a later patch.
SourceSink is currently the only function using ->setup() at config level.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Removes a couple of:
|drivers/usb/gadget/s3c-hsudc.c: In function 's3c_hsudc_epin_intr':
|drivers/usb/gadget/s3c-hsudc.c:438:2: warning: passing argument 1 of '__raw_readl' makes pointer from integer without a cast
|arch/arm/include/asm/io.h:104:19: note: expected 'const volatile void *' but argument is of type 'unsigned int'
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Lets assume nokia_bind() starts with "return -EINVAL". After loading the
gadget we end up with:
|udc dummy_udc.0: registering UDC driver [g_nokia]
|BUG: unable to handle kernel NULL pointer dereference at 00000040
|IP: [<c11f9555>] __list_add+0x25/0xf0
|Call Trace:
| [<c12d4e21>] rollback_registered+0x21/0x40
| [<c12d513f>] unregister_netdevice_queue+0x4f/0xa0
| [<c12d5259>] unregister_netdev+0x19/0x30
| [<f81335b2>] gphonet_cleanup+0x32/0x50 [g_nokia]
| [<f8133f1c>] nokia_unbind+0x1c/0x2a [g_nokia]
| [<f802509f>] __composite_unbind.constprop.10+0x4f/0xb0 [libcomposite]
| [<f80255be>] composite_bind+0x1ae/0x230 [libcomposite]
| [<c129e576>] usb_gadget_probe_driver+0xc6/0x1b0
| [<f8024aba>] usb_composite_probe+0x7a/0xa0 [libcomposite]
That is crash from nokia_unbind() invoked via nokia_bind(). This crash
will look different we if make it until usb_string_ids_tab() before we
enter an error condition in the probe function.
nokia_bind_config() tries to clean up which is IMHO the right thing to
do. Leaving things as-is and hoping that its unbind() will clean it up
is kinda backwards. Especially since the bind function never succeeded so
it can't know how much it needs to clean up.
This fixes the behaviour by not calling the driver's unbind function if
its bind function failed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch sets scsi_host->max_id as 1 if the device's quirk
flag of US_FL_SCM_MULT_TARG isn't set, because there are only 6
mass storage devices marked as mutiple targets from unusual_devs.h.
This patch is a small optimization about scanning targets, and
avoid scanning other 7 non-existed targets for single target
device.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To show the relationship between usb port and child device,
add link file "port" under usb device's sysfs directoy and
"device" under usb port device's sysfs directory. They are linked
to each other.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some platforms provide usb port connect types through ACPI. This
patch is to add this new attribute to expose these information
to user space.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to fix compilation error and warning on the arm and blackfin.
Add linux/slab.h head file to driver/usb/core/port.c. These are reported
from 0-DAY kernel build testing backend.
head: 6e30d7cba9
commit: 6e30d7cba9 [26/26] usb: Add driver/usb/core/(port.c,hub.h) files
config: make ARCH=arm at91_dt_defconfig
All error/warnings:
drivers/usb/core/port.c: In function 'usb_port_device_release':
>> drivers/usb/core/port.c:25:2: error: implicit declaration of function 'kfree' [-Werror=implicit-function-declaration]
drivers/usb/core/port.c: In function 'usb_hub_create_port_device':
>> drivers/usb/core/port.c:38:2: error: implicit declaration of function 'kzalloc' [-Werror=implicit-function-declaration]
>> drivers/usb/core/port.c:38:40: error: 'GFP_KERNEL' undeclared (first use in this function)
drivers/usb/core/port.c:38:40: note: each undeclared identifier is reported only once for each function it appears in
cc1: some warnings being treated as errors
head: 6e30d7cba9
commit: 6e30d7cba9 [26/26] usb: Add driver/usb/core/(port.c,hub.h) files
config: make ARCH=blackfin BF526-EZBRD_defconfig
All warnings:
drivers/usb/core/port.c: In function 'usb_port_device_release':
drivers/usb/core/port.c:25:2: error: implicit declaration of function 'kfree' [-Werror=implicit-function-declaration]
drivers/usb/core/port.c: In function 'usb_hub_create_port_device':
drivers/usb/core/port.c:38:2: error: implicit declaration of function 'kzalloc' [-Werror=implicit-function-declaration]
>> drivers/usb/core/port.c:38:11: warning: assignment makes pointer from integer without a cast [enabled by default]
cc1: some warnings being treated as errors
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.
The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer. Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.
bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY. The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.
add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function old new delta
chr_dev_init 166 170 +4
allow_signal 80 82 +2
static.__warned 143 142 -1
disallow_signal 63 62 -1
__set_special_pids 95 94 -1
unregister_console 126 121 -5
start_kernel 546 541 -5
register_console 593 588 -5
copy_from_user 45 40 -5
sys_setsid 128 120 -8
sys_vhangup 32 19 -13
do_exit 1543 1526 -17
bitmap_zero 60 40 -20
arch_local_irq_save 137 117 -20
release_task 674 652 -22
static.spin_unlock_irqrestore 308 260 -48
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to create driver/usb/core/(port.c,hub.h) files and move usb
port related code into port.c.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The callers expect this function to return zero on success or -EIO if it
times out. The type should be int instead of unsigned short.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kill custom closing_wait implementation and let the tty layer handle it
instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Query hardware-buffer status in chars_in_buffer should the write fifo be
empty.
This is needed to make the tty layer wait for hardware buffers to drain
on close.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Grab disconnect mutex in chars_in_buffer before checking disconnected
flag or calling driver specific function.
This allows subdrivers to query any hardware buffer status without
having to handle the locking themselves.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use tty-port drain delay rather than custom implementation in
chase_port.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move write-fifo flushing from chase_port to close where it belongs.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are 3 USB patches for 3.8-rc4. Two of them are new device id
patches, and the third fixes a reported oops in the io_ti USB serial
driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlD5o/cACgkQMUfUDdst+ym9xQCfcQOzPUnnU1EfJkHVeuSIdR8e
3hsAn26GuvNTIzqt392ML95dOLxAqe8Z
=iOum
-----END PGP SIGNATURE-----
Merge tag 'usb-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are 3 USB patches for 3.8-rc4. Two of them are new device id
patches, and the third fixes a reported oops in the io_ti USB serial
driver"
* tag 'usb-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: io_ti: Fix NULL dereference in chase_port()
USB: option: add TP-LINK HSUPA Modem MA180
USB: option: blacklist network interface on ONDA MT8205 4G LTE
Adding support to parse device node data in order to get
required properties to set pmu isolation for usb-phy.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Directly casting a work_struct pointer to a delayed_work is risky if the
work member of struct delayed_work is ever moved from being the first
member.
Instead, use the inline function to_delayed_work(), which does the same
cast in a safer way (using container_of).
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adding the transceiver to hsotg driver. Keeping the platform data
for continuing the smooth operation for boards which still uses it
Signed-off-by: Praveen Paneri <p.paneri@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This driver uses usb_phy interface to interact with s3c-hsotg. Supports
phy_init and phy_shutdown functions to enable/disable usb phy. Support
will be extended to host controllers and more Samsung SoCs.
Signed-off-by: Praveen Paneri <p.paneri@samsung.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 controller curretly depends on USB && USB_GADGET.
Some hardware may like to use only host feature on dwc3,
or only gadget feature.
So, removing this dependency of USB_DWC3 on USB and USB_GADGET.
Adding the mode of operaiton of DWC3 also here
HOST/GADGET/DUAL_ROLE based on which features are enabled.
[ balbi@ti.com :
. make sure we have default modes for all possible Kernel
configurations.
. Remove the config -> menuconfig change as it's unnecessary
. switch over to IS_ENABLED() ]
CC: Doug Anderson <dianders@chromium.org>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
I am not sure, why I found it during SG debugging. But, I noticed that
even when req_queued list was empty, there were some request in
request_list having queued flag true. If I run test second time, it
first removes all request from request_list and hence busy_slot was
wrongly incremented.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To work with scatter gather properly, fixes have been done in number of
functions. I will explain requirement of each fixes one by one.
start_slot: used to retrieve all request of SG during cleanup
dwc3_gadget_giveback: We need to skip link TRB if it was one of the
intermediate TRB of SG.
dwc3_prepare_one_trb: We need to track all submitted TRBs during
cleanup. Since, all TRBs would be serially allocated, so we can just
keep starting slot info and we can always find rest of them. We need to
pass sg node number, so that we cab appropriately program ISOC_FIRST/ISOC,
Chain etc.
dwc3_prepare_trbs: last_one should be set when it is last node
of SG as well as last node of request_list.
__dwc3_cleanup_done_trbs: It has been prepared after re-factorization of
dwc3_cleanup_done_reqs. It is called for each TRB of SG.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
UPDATE_TRANSFER does not need any parameters. So, no need to prepare it.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we reach to link trb, we just need to increase free_slot and then
calculate TRB. Return is not correct, as it will cause wrong TRB DMA
address to fetch in case of update transfer.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There were still some corner cases where isoc transfer was not able to
restart, specially when missed isoc does not happen , and in fact gadget does
not queue any new request during giveback.
Cleanup function calls giveback first, which provides a way to queue
another request to gadget. But gadget did not had any data. So , it did
not call ep_queue. To twist it further, gadget did not queue till
cleanup for last queued TRB is called. If we ever reach this scenario,
we must call END TRANSFER, so that we receive a new xfernotready with
information about current microframe number.
Also insure that there is no request submitted to core when issuing END
TRANSFER.
Cc: <stable@vger.kernel.org> # v3.8
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Its better to return from each if condition as they are mutually
exclusive.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are two reasons to generate missed isoc.
1. when the host does not poll for all the data.
2. because of application-side delays that prevent all the data from
being transferred in programmed microframe.
Current code was able to handle first case only. This patch handles
scenario 2 as well.Scenario 2 sometime may occur with complex gadget
application, however it can be easily reproduced for testing purpose as
follows:
a. use isoc binterval as 1 in f_sourcesink.
b. use pattern=0
c. introduce a delay of 150us deliberately in source_sink_complete, so
that after few frames it lands into scenario 2.
d. now run testusb 16 (isoc in test). You will notice that if this
patch is not applied then isoc transfer is not able to recover after
first missed.
Current patch's approach is as under:
If missed isoc occurs and there is no request queued then issue END
TRANSFER, so that core generates next xfernotready and we will issue a
fresh START TRANSFER.
If there are still queued request then wait, do not issue either END or
UPDATE TRANSFER, just attach next request in request_list during giveback.
If any future queued request is successfully transferred then we will issue
UPDATE TRANSFER for all request in the request_list.
Cc: <stable@vger.kernel.org> # v3.6 v3.7 v3.8
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Synopsys says:
The HIRD Threshold field must be set to ‘0’ when the device core is
operating in super speed mode.
This patch implements above statement.
Cc: <stable@vger.kernel.org> # v3.6 v3.7 v3.8
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add missing braces around an if block in ffs_fs_parse_opts. This broke
parsing the uid/gid mount options and causes mount to fail when using
uid/gid. This has been introduced by commit b9b73f7c (userns: Convert usb
functionfs to use kuid/kgid where appropriate) in 3.7.
Cc: <stable@vger.kernel.org>
Signed-off-by: Benoit Goby <benoit@android.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc3_gadget_set_ep_config expects maxburst as incremented by 1. So, by
default initialize ep->maxburst to 1 for ep0.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As mach/hardware.h is deleted, we can't visit platform code at driver.
It has no phy driver to combine with this controller, so it has to use
ioremap to map phy address as a workaround.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As mach/hardware.h is deleted, we need to use platform_device_id to
differentiate SoCs. Besides, one cpu_is_mx35 is useless as it has
already used pdata to differentiate runtime
Meanwhile we update the platform code accordingly.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the following:
WARNING: vmlinux.o(.text+0x1e709c): Section mismatch in reference from the funct
ion dma_controller_create() to the function .init.text:cppi_controller_start()
The function dma_controller_create() references
the function __init cppi_controller_start().
This is often because dma_controller_create lacks a __init
annotation or the annotation of cppi_controller_start is wrong.
This warning is there due to the deficiency in the commit 07a67bbb (usb: musb:
Make dma_controller_create __devinit).
Since the start() method is only called from musb_init_controller() which is
not annotated, drop '__init' annotation from cppi_controller_start() and also
cppi_pool_init() since it gets called from that function, to avoid another
section mismatch warning...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@vger.kernel.org # 3.7+
Signed-off-by: Felipe Balbi <balbi@ti.com>
The devm_ functions allocate memory that is released when a driver
detaches. This makes the code smaller and a bit simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently we're allocating an entire page to
serve as our event buffer. Provided our events
are 4 bytes long, it's very unlikely we will
even trigger 1k events at once.
Even in the worst case scenario where every
endpoint triggers one event and we still have
a couple of error events, that would still
be less than 40 events.
In order to cope with future versions of the
IP which could (or could not) increase the
amount of possible events to trigger
simultaneously, we're using an arbitrary size
of 64 events for our event buffer.
We're saving 3840 bytes by doing so.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is to fix up a build problem with a wireless driver due to the
dynamic-debug patches in this branch.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch converts the drivers in drivers/usb/* to use the
module_platform_driver_probe() macro which makes the code smaller and
a bit simpler.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver description files gives these names to the vendor specific
functions on this modem:
Diagnostics VID_2357&PID_0201&MI_00
NMEA VID_2357&PID_0201&MI_01
Modem VID_2357&PID_0201&MI_03
Networkcard VID_2357&PID_0201&MI_04
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver description files gives these names to the vendor specific
functions on this modem:
Diag VID_19D2&PID_0265&MI_00
NMEA VID_19D2&PID_0265&MI_01
AT cmd VID_19D2&PID_0265&MI_02
Modem VID_19D2&PID_0265&MI_03
Net VID_19D2&PID_0265&MI_04
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the warning,
6a099c6365 [4/10] USB: misc: Add USB3503 High-Speed Hub Controller
drivers/usb/misc/usb3503.c:238 usb3503_probe() error: we previously assumed 'pdata' could be null (see line 196)
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 00a0b1d58a (usb: musb: omap: Add device
tree support for omap musb glue) assigns result of devm_kzalloc() call to
the 'config' variable but then checks for NULL the 'data' variable (already
checked after previous call). Thus we risk a kernel oops further when data
pointed by 'config' is written to by subsequent of_property_read_u32() calls
iff the allocation happens to fail...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch let glue driver return -EPROBE_DEFER if the transceiver
is not readly, so we can support defer probe on musb to fix the
below error on 3.7-rc5 if transceiver drivers are built as module:
[ 19.052490] unable to find transceiver of type USB2 PHY
[ 19.072052] HS USB OTG: no transceiver configured
[ 19.076995] musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -19
[ 19.089355] musb-hdrc: probe of musb-hdrc.0.auto rejects match -19
[ 19.096771] driver: 'musb-omap2430': driver_bound: bound to device 'musb-omap2430'
[ 19.105194] bus: 'platform': really_probe: bound device musb-omap2430 to driver musb-omap2430
[ 19.174407] bus: 'platform': add driver twl4030_usb
[ 19.179656] bus: 'platform': driver_probe_device: matched device twl4030_usb with driver twl4030_usb
[ 19.202270] bus: 'platform': really_probe: probing driver twl4030_usb with device twl4030_usb
[ 19.214172] twl4030_usb twl4030_usb: HW_CONDITIONS 0xc0/192; link 3
[ 19.239624] musb-omap2430 musb-omap2430: musb core is not yet ready
[ 19.246765] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[ 19.254516] driver: 'twl4030_usb': driver_bound: bound to device 'twl4030_usb'
[ 19.263580] bus: 'platform': really_probe: bound device twl4030_usb to driver twl4030_usb
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: <stable@vger.kernel.org> v3.8
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In the fail1~fail5 failure path, pm_runtime_disable() should
be called to avoid 'Unbalanced pm_runtime_enable' error in
next probe() which may be triggered by defer probe or next
'modprobe musb_hdrc'.
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: <stable@vger.kernel.org> v3.8
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Whenever an URB is programmed for transfer, the TXFIFO
is flushed. This results in valid packets of the
previous transfer to get flushed when double buffering
is enabled (The MUSB_TXCSR_FIFONOTEMPTY bit in TXCSR
is set indicating that a packet in the FIFO is yet to be sent)
For ex:- In Host mode Audio, noise is heard in the headset
when double buffering is enabled on the ISO endpoint.
The fifo flush is removed for double buffering case.
The fifo is now flushed only in cases of error or when
aborting a transfer.
Also, In Host MSC case, data toggle errors are seen when double
buffering is enabled on the bulk endpoint. Whenever an URB is
programmed for transfer, the data toggle is set manually
resulting in data toggle errors on the bus. Leave the data
toggle handling upto the hardware in the double buffering case.
Signed-off-by: supriya karanth <supriya.karanth@stericsson.com>
Signed-off-by: Praveena NADAHALLY <praveen.nadahally@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 00a0b1d58a (usb: musb: omap: Add device
tree support for omap musb glue) added assignments of the 'ret' variable to
-ENOMEM on *some* error paths of the calls to devm_kzalloc(), while that
variable was already pre-initialized for to that value, so these assignments
were completely redundant. Kill them, fixing overindented string, while at it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch converts the module to use clk_prepare_enable and
clk_disable_unprepare variants as required by common clock framework.
Without this the system crash during probe function.
Cc: <stable@vger.kernel.org> # v3.7 v3.8
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_string this time.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_char is the next one to proceed. This one is used all
over the code, so the patch is huge.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty pointer in
many call sites. Only tty_port will be needed and hence no more
tty_port_tty_get calls in those paths.
Now 4 string flipping ones are on turn:
* tty_insert_flip_string_flags
* tty_insert_flip_string_fixed_flag
* tty_prepare_flip_string
* tty_prepare_flip_string_flags
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty pointer in
many call sites. Only tty_port will be needed and hence no more
tty_port_tty_get calls in those paths.
Here we start with tty_buffer_request_room.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conflicts:
Documentation/networking/ip-sysctl.txt
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
Both conflicts were simply overlapping context.
A build fix for qlcnic is in here too, simply removing the added
devinit annotations which no longer exist.
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are a bunch of USB fixes for your 3.8-rc3 tree. They all either fix
problems that have been reported (like the xhci/hub changes) or add new device
ids to existing drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDzjz0ACgkQMUfUDdst+yn5YwCeOyqqCgQvyuP2JsacN/2a4wRN
Wn4AoM/Pg+b+B8M7Z/SBO10DRzj24xYj
=Kkq8
-----END PGP SIGNATURE-----
Merge tag 'usb-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a bunch of USB fixes for your 3.8-rc3 tree. They all either
fix problems that have been reported (like the xhci/hub changes) or
add new device ids to existing drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (39 commits)
usb: ftdi_sio: Crucible Technologies COMET Caller ID - pid added
usb: host: ohci-tmio: fix compile warning
USB: Add device quirk for Microsoft VX700 webcam
USB: ehci-fsl: fix regression on mpc5121e
usb: chipidea: Allow disabling streaming not only in udc mode
USB: fsl-mph-dr-of: fix regression on mpc5121e
USB: select USB_ARCH_HAS_EHCI for MXS
USB: hub: handle claim of enabled remote wakeup after reset
USB: cdc-acm: Add support for "PSC Scanning, Magellan 800i"
USB: option: add Nexpring NP10T terminal id
USB: option: add Telekom Speedstick LTE II
USB: option: blacklist network interface on ZTE MF880
usb: imx21-hcd: Include missing linux/module.h
USB: option: Add new MEDIATEK PID support
USB: ehci: make debug port in-use detection functional again
USB: usbtest: fix test number in log message
xhci: Avoid "dead ports", add roothub port polling.
USB: Handle warm reset failure on empty port.
USB: Ignore port state until reset completes.
USB: Increase reset timeout.
...
Simple fix to add support for Crucible Technologies COMET Caller ID
USB decoder - a device containing FTDI USB/Serial converter chip,
handling 1200bps CallerID messages decoded from the phone line -
adding correct USB PID is sufficient.
Tested to apply cleanly and work flawlessly against 3.6.9, 3.7.0-rc8
and 3.8.0-rc3 on both amd64 and x86 arches.
Signed-off-by: Tomasz Mloduchowski <q@qdot.me>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following compile warning:
In file included from drivers/usb/host/ohci-hcd.c:1170:0:
drivers/usb/host/ohci-tmio.c: In function 'tmio_start_hc':
drivers/usb/host/ohci-tmio.c:130:2: warning: format '%llx' expects argument of type 'long long unsigned int', but argument 4 has type 'resource_size_t' [-Wformat]
seen on ARM 32-bit builds.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since Efika MX platform support (pre-devicetree) was removed from the tree
this code no longer has any possibility of running and clutters up the
driver which is being replaced by the chipidea host in the future anyway.
Signed-off-by: Matt Sealey <matt@genesi-usa.com>
Tested-by: Steev Klimazewski <steev@genesi-usa.com>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sarah pointed out that the USB3.0 spec also updates the amount of power
that may be consumed by the device and quoted 9.2.5.1:
|"The amount of current draw for SuperSpeed devices are increased to 150
|mA for low-power devices and 900 mA for high-power"
This patch tries to update all users to use the larger values for
SuperSpeed devices and use the "old" ones for everything else.
While here, two other changes suggested by Alan:
- the comment referering to 7.2.1.1 has been updated to 7.2.1 which is
the correct source of the action.
- the check for hubs with zero ports has been removed.
- compute bus power by full_load * num_ports on root hubs
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB 2.0 specification says that bMaxPower is the maximum power
consumption expressed in 2 mA units and the USB 3.0 specification says
that it is expressed in 8 mA units.
This patch adds a helper function usb_get_max_power() which computes the
value based on config & usb_device's speed value. The the device descriptor
dump computes the value on its own.
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
although we can not say it is surely a bug.
it is better to set urb->hcpriv = NULL, after finish calling
urb_free_priv.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running a scp transfer using a USB/Ethernet adapter the following crash
happens:
$ scp test.tar.gz fabio@192.168.1.100:/home/fabio
fabio@192.168.1.100's password:
test.tar.gz 0% 0 0.0KB/s --:-- ETA
------------[ cut here ]------------
WARNING: at net/sched/sch_generic.c:255 dev_watchdog+0x2cc/0x2f0()
NETDEV WATCHDOG: eth0 (asix): transmit queue 0 timed out
Modules linked in:
Backtrace:
[<80011c94>] (dump_backtrace+0x0/0x10c) from [<804d3a5c>] (dump_stack+0x18/0x1c)
r6:000000ff r5:80412388 r4:80685dc0 r3:80696cc0
[<804d3a44>] (dump_stack+0x0/0x1c) from [<80021868>]
(warn_slowpath_common+0x54/0x6c)
[<80021814>] (warn_slowpath_common+0x0/0x6c) from [<80021924>]
(warn_slowpath_fmt+0x38/0x40)
...
Setting SDIS (Stream Disable Mode- bit 4 of USBMODE register) fixes the problem.
However, in current code CI13XXX_DISABLE_STREAMING flag is only set in udc mode,
so allow disabling streaming also in host mode.
Tested on a mx6qsabrelite board.
Suggested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fsl-ehci probing fails on mpc5121e:
...
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: Could not get controller version
fsl-ehci fsl-ehci.0: can't setup
fsl-ehci fsl-ehci.0: USB bus 1 deregistered
fsl-ehci fsl-ehci.0: init fsl-ehci.0 fail, -22
fsl-ehci: probe of fsl-ehci.0 failed with error -22
Fix it by returning appropriate version info for mpc5121, too.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 09f6ffde (USB: EHCI: fix build error by making ChipIdea host a
normal EHCI driver) introduced a dependency on USB_EHCI_HCD for the
chipidea USB host driver, that in turns depends on USB_ARCH_HAS_EHCI.
If this symbol is not set for MXS, the MXS boards are not able to use
the chipidea driver anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some touchscreens have buggy firmware which claims
remote wakeup to be enabled after a reset. They nevertheless
crash if the feature is cleared by the host.
Add a check for reset resume before checking for
an enabled remote wakeup feature. On compliant
devices the feature must be cleared after a reset anyway.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new function to unlink and abort requests from the work
list, call it on bus reset and disconnect where we kill all
in-flight urbs. Also reorder calls in disconnect to first
cancel transfers, then remove the scsi hba.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two changes. First we check whenever the request is linked in the work
list and if so take it out. Second check whenever the command is
actually in flight before asking the device to cancel it via task
management, and in case it isn't just zap the data urbs and finish it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keep track whenever the request is linked into the work list or not.
Needed for request abort.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uas_unlink_data_urbs uses this to make sure the the scsi command is
not released while looking at it. This will be needed when we start
calling uas_unlink_data_urbs in the request cancel code paths.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add uas_unlink_data_urbs function to cancel in-flight data urbs.
Moves existing code into a separate function.
[ v2: also drop the locking, just call usb_unlink_urb no matter what,
which is safe because the usb core guarantees the completion
callback is called only once ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds new driver of SMSC USB3503 USB 2.0 hub controller with HSIC
upstream connectivity and three USB 2.0 downstream ports. The specification
can be found from 'http://www.smsc.com/index.php?tid=295&pid=325'.
The current version have been tested very basic features switching the modes,
HUB-MODE and STANDBY-MODE.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding support "PSC Scanning, Magellan 800i" in cdc-acm
Very simple, but very necessary.
Suitable for all versions of the kernel > 2.6
Signed-off-by: Denis N Ladin <denladin@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
also known as Alcatel One Touch L100V LTE
The driver description files gives these names to the vendor specific
functions on this modem:
Application1: VID_1BBB&PID_011E&MI_00
Application2: VID_1BBB&PID_011E&MI_01
Modem: VID_1BBB&PID_011E&MI_03
Ethernet: VID_1BBB&PID_011E&MI_04
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Include <linux/module.h>, so that the following errors are fixed:
drivers/usb/host/imx21-hcd.c:1929:20: error: expected declaration specifiers or '...' before string constant
drivers/usb/host/imx21-hcd.c:1930:15: error: expected declaration specifiers or '...' before string constant
drivers/usb/host/imx21-hcd.c:1931:16: error: expected declaration specifiers or '...' before string constant
drivers/usb/host/imx21-hcd.c:1932:14: error: expected declaration specifiers or '...' before string constant
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In option.c, add some new MEDIATEK PIDs support for MEDIATEK new products. This
is a MEDIATEK inc. release patch.
Signed-off-by: Quentin.Li <snowmanli88@163.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "mult" factor is not updated properly for the can_bulk_split()
case.
The AUTOSET bit in the TXCSR is not being set if the "mult"
factor is greater than 1 for the High Bandwidth ISO case.
But the "mult" factor is also greater than 1 in case of Full speed
bulk transfers with the packet splitting in TXMAXP register
enabled with can_bulk_split().
Without the AUTOSET the DMA transfers will not progress in mode1
[ balbi@ti.com : fix braces placement ]
Signed-off-by: supriya karanth <supriya.karanth@stericsson.com>
Signed-off-by: Praveena NADAHALLY <praveen.nadahally@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The TXMAXP register is not set correctly for full speed bulk case
when the can_bulk_split() is used. Without this PIO transfers will
not take place correctly
The "mult" factor needs to be updated correctly for the
can_bulk_split() case
The AUTOSET bit in the TXCSR is not being set if the "mult"
factor is greater than 0 for the High Bandwidth ISO case.
But the "mult" factor is also greater than 0 in case of Full speed
bulk transfers with the packet splitting in TXMAXP register
Without the AUTOSET the DMA transfers will not progress in mode1
[ balbi@ti.com : add braces to both branches ]
Signed-off-by: supriya karanth <supriya.karanth@stericsson.com>
Signed-off-by: Praveena NADAHALLY <praveen.nadahally@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
kstrtoul() checks for overflow which simple_strtoul() does not pluss
it has “*end == 0” check in it as well. As a side effect, a new
line character is now accepted, but this should not be an issue.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
devm_regulator_bulk_get is device managed and saves some cleanup
and exit code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
devm_regulator_bulk_get is device managed and makes exit code
simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There's no need to test whether a (delayed) work item in pending
before queueing, flushing or cancelling it. Most uses are unnecessary
and quite a few of them are buggy.
Remove unnecessary pending tests from at91_udc. Only compile tested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: linux-usb@vger.kernel.org
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In the IN case, since the USB request is allocated only when
the source/sink function is started and never freed, the USB ept
buffer needs to be initialized only at the beginning. This change
results into a more performant g_zero module, especially when
'pattern=1' is selected.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The USB 2.0 specification says that bMaxPower is the maximum power
consumption expressed in 2 mA units and the USB 3.0 specification says
that it is expressed in 8 mA units.
This patch renames bMaxPower to MaxPower and the various /2 and *2 are
removed. Before reporting the config descriptor, the proper value is
computer based on the speed, all in-tree users are updated. MaxPower is
also increased to u16 so we can store the nokia gadget value which is
larger than the max value allowed for u8.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
| In file included from drivers/usb/gadget/acm_ms.c:43:
| f_mass_storage.c:2199:18: warning: comparison of unsigned expression >= 0 is always true [-Wtautological-compare]
| if (common->lun >= 0 && common->lun < common->nluns)
| ~~~~~~~~~~~ ^ ~
common->lun is defined as "unsigned int" so its value is always >= 0.
It is assigned via cbw->Lun which is defined as u8 so it is also not
abused as -1.
[ mina86@mina86.com : make lun unsigned int and use %u in DBG() macro for it ]
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The variable ep is initialized but never used
otherwise, so remove the unused variable.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
pre_eject and post_eject are not used by anyone. Removing them.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is ndp16_opts and ndp32_opts which are both global and only one
member is ever written. This patch makes the variable read-only and
moves the one member that is ever written into the private struct f_ncm.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes the last pieces of the file_storage gadget hidden in
storage_common behind __maybe_unused bars.
The CBI bits have no user on the gadget side. Only file_storage
implemented the obsolete protocol.
The additional USB3.0 descriptors were served by file_storage, the other
gadgets are using composite for this.
Acked-by: Michal Nazarewicz <mpn@google.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Debug port in-use determination must be done before the controller gets
reset the first time, i.e. before the call to ehci_setup() as of commit
1a49e2ac96. That commit effectively
rendered commit 9fa5780bee useless.
While moving that code around, also fix the BAR determination - the
respective capability field is a 3- rather than a 2-bit one -, and use
PCI_CAP_ID_DBG instead of the literal 0x0a.
It's unclear to me whether the debug port functionality is important
enough to warrant fixing this in stable kernels too.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1639) fixes a minor bug in the usbtest driver. Due to
concurrent changes, a test originally written as number 17 got changed
to number 24, but the corresponding change was not made in the log
message. This updates the log message.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
Here's some patches for 3.9. They further improve the warm reset
error handling, but they're too big to go into stable. There's also a
patch to remove an unused variable in the xHCI driver.
As I mentioned, you'll need to merge usb-linus into usb-next before
applying these patches.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=VBlC
-----END PGP SIGNATURE-----
Merge tag 'for-usb-next-2013-01-03' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
usb-next: Further warm reset improvements
Hi Greg,
Here's some patches for 3.9. They further improve the warm reset
error handling, but they're too big to go into stable. There's also a
patch to remove an unused variable in the xHCI driver.
As I mentioned, you'll need to merge usb-linus into usb-next before
applying these patches.
Sarah Sharp
Hi Greg,
Happy New Year! Here's some bug fixes for 3.8. I have usb-next
patches that are based on this set, so please merge your usb-linus
branch into usb-next after this set is applied.
The bulk of the patchset (patches 2-7) improve the USB core's warm
reset error handling.
There's also one patch that fixes an arithmetic error in the xHCI
driver, and another to avoid the "dead ports" issue caused by
unhandled port status change events.
These are all marked for stable.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9YSo
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2013-01-03' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
Sarah says:
usb-linus: USB core fixes for warm reset
Hi Greg,
Happy New Year! Here's some bug fixes for 3.8. I have usb-next
patches that are based on this set, so please merge your usb-linus
branch into usb-next after this set is applied.
The bulk of the patchset (patches 2-7) improve the USB core's warm
reset error handling.
There's also one patch that fixes an arithmetic error in the xHCI
driver, and another to avoid the "dead ports" issue caused by
unhandled port status change events.
These are all marked for stable.
Sarah Sharp
Here is the first set of fixes for v3.8-rc cycle.
There is a build fix for musb's dsps glue layer caused
by some header cleanup on the OMAP tree.
Marvel's USB drivers got a fix up for clk API usage
switching over to clk_prepare() calls.
u_serial has a bug fix for a missing wake_up() which
would make gs_cleanup() wait forever for gs_close()
to finish.
A minor bug fix on dwc3's debugfs interface which
would make us read wrong addresses when dumping
all registers.
dummy_hcd learned how to enumerate g_multi.
s3c-hsotg now understands that we shouldn't kfree()
memory allocated with devm_*.
Other than that, there are a bunch of other minor fixes
on renesas_usbhs, tcm_usb_gadget and amd5536udc.
All patches have been pending on mailing for many weeks
and shouldn't cause any problems.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=UsKi
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe says:
usb: fixes for v3.8-rc2
Here is the first set of fixes for v3.8-rc cycle.
There is a build fix for musb's dsps glue layer caused
by some header cleanup on the OMAP tree.
Marvel's USB drivers got a fix up for clk API usage
switching over to clk_prepare() calls.
u_serial has a bug fix for a missing wake_up() which
would make gs_cleanup() wait forever for gs_close()
to finish.
A minor bug fix on dwc3's debugfs interface which
would make us read wrong addresses when dumping
all registers.
dummy_hcd learned how to enumerate g_multi.
s3c-hsotg now understands that we shouldn't kfree()
memory allocated with devm_*.
Other than that, there are a bunch of other minor fixes
on renesas_usbhs, tcm_usb_gadget and amd5536udc.
All patches have been pending on mailing for many weeks
and shouldn't cause any problems.
Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This snuck in from a different tree during the merge and needs to be
removed.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The union xhci_trb *trb variable is defined and assigned
inside the xHCI IRQ handler function but is never used.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Refactor hub_port_wait_reset into a small loop to wait for the port
reset to be complete, and then a larger block to deal with the final
port status. This patch should not change any current behavior.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Change the code that manually issues a Set Port Feature(Link State) to
use the new helper function hub_set_port_link_state().
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
A USB 3.0 device can transition to the Inactive state if a U1 or U2 exit
transition fails. The current code in hub_events simply issues a warm
reset, but does not call any pre-reset or post-reset driver methods (or
unbind/rebind drivers without them). Therefore the drivers won't know
their device has just been reset.
hub_events should instead call usb_reset_device. This means
hub_port_reset now needs to figure out whether it should issue a warm
reset or a hot reset.
Remove the FIXME note about needing disconnect() for a NOTATTACHED
device. This patch fixes that.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
When a hot reset fails on a USB 3.0 port, the current port reset code
recursively calls hub_port_reset inside hub_port_wait_reset. This isn't
ideal, since we should avoid recursive calls in the kernel, and it also
doesn't allow us to issue multiple warm resets on reset failures.
Rip out the recursive call. Instead, add code to hub_port_reset to
issue a warm reset if the hot reset fails, and try multiple warm resets
before giving up on the port.
In hub_port_wait_reset, remove the recursive call and re-indent. The
code is basically the same, except:
1. It bails out early if the port has transitioned to Inactive or
Compliance Mode after the reset completed.
2. It doesn't consider a connect status change to be a failed reset. If
multiple warm resets needed to be issued, the connect status may have
changed, so we need to ignore that and look at the port link state
instead. hub_port_reset will now do that.
3. It unconditionally sets udev->speed on all types of successful
resets. The old recursive code would set the port speed when the second
hub_port_reset returned.
The old code did not handle connected devices needing a warm reset well.
There were only two situations that the old code handled correctly: an
empty port needing a warm reset, and a hot reset that migrated to a warm
reset.
When an empty port needed a warm reset, hub_port_reset was called with
the warm variable set. The code in hub_port_finish_reset would skip
telling the USB core and the xHC host that the device was reset, because
otherwise that would result in a NULL pointer dereference.
When a USB 3.0 device reset migrated to a warm reset, the recursive call
made the call stack look like this:
hub_port_reset(warm = false)
hub_wait_port_reset(warm = false)
hub_port_reset(warm = true)
hub_wait_port_reset(warm = true)
hub_port_finish_reset(warm = true)
(return up the call stack to the first wait)
hub_port_finish_reset(warm = false)
The old code didn't want to notify the USB core or the xHC host of device reset
twice, so it only did it in the second call to hub_port_finish_reset,
when warm was set to false. This was necessary because
before patch two ("USB: Ignore xHCI Reset Device status."), the USB core
would pay attention to the xHC Reset Device command error status, and
the second call would always fail.
Now that we no longer have the recursive call, and warm can change from
false to true in hub_port_reset, we need to have hub_port_finish_reset
unconditionally notify the USB core and the xHC of the device reset.
In hub_port_finish_reset, unconditionally clear the connect status
change (CSC) bit for USB 3.0 hubs when the port reset is done. If we
had to issue multiple warm resets for a device, that bit may have been
set if the device went into SS.Inactive and then was successfully warm
reset.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
The next patch will refactor the hub port code to rip out the recursive
call to hub_port_reset on a failed hot reset. In preparation for that,
make sure all code paths can deal with being called with a NULL udev.
The usb_device will not be valid if warm reset was issued because a port
transitioned to the Inactive or Compliance Mode on a device connect.
This patch should have no effect on current behavior.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
The EHCI host controller needs to prevent EHCI initialization when the
UHCI or OHCI companion controller is in the middle of a port reset. It
uses ehci_cf_port_reset_rwsem to do this. USB 3.0 hubs can't be under
an EHCI host controller, so it makes no sense to down the semaphore for
USB 3.0 hubs. It also makes the warm port reset code more complex.
Don't down ehci_cf_port_reset_rwsem for USB 3.0 hubs.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
The USB core hub thread (khubd) is designed with external USB hubs in
mind. It expects that if a port status change bit is set, the hub will
continue to send a notification through the hub status data transfer.
Basically, it expects hub notifications to be level-triggered.
The xHCI host controller is designed to be edge-triggered on the logical
'OR' of all the port status change bits. When all port status change
bits are clear, and a new change bit is set, the xHC will generate a
Port Status Change Event. If another change bit is set in the same port
status register before the first bit is cleared, it will not send
another event.
This means that the hub code may lose port status changes because of
race conditions between clearing change bits. The user sees this as a
"dead port" that doesn't react to device connects.
The fix is to turn on port polling whenever a new change bit is set.
Once the USB core issues a hub status request that shows that no change
bits are set in any USB ports, turn off port polling.
We can't allow the USB core to poll the roothub for port events during
host suspend because if the PCI host is in D3cold, the port registers
will be all f's. Instead, stop the port polling timer, and
unconditionally restart it when the host resumes. If there are no port
change bits set after the resume, the first call to hub_status_data will
disable polling.
This patch should be backported to stable kernels with the first xHCI
support, 2.6.31 and newer, that include the commit
0f2a79300a "USB: xhci: Root hub support."
There will be merge conflicts because the check for HC_STATE_SUSPENDED
was moved into xhci_suspend in 3.8.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
An empty port can transition to either Inactive or Compliance Mode if a
newly connected USB 3.0 device fails to link train. In that case, we
issue a warm reset. Some devices, such as John's Roseweil eusb3
enclosure, slip back into Compliance Mode after the warm reset.
The current warm reset code does not check for device connect status on
warm reset completion, and it incorrectly reports the warm reset
succeeded. This causes the USB core to attempt to send a Set Address
control transfer to a port in Compliance Mode, which will always fail.
Make hub_port_wait_reset check the current connect status and link state
after the warm reset completes. Return a failure status if the device
is disconnected or the link state is Compliance Mode or SS.Inactive.
Make hub_events disable the port if warm reset fails. This will disable
the port, and then bring it back into the RxDetect state. Make the USB
core ignore the connect change until the device reconnects.
Note that this patch does NOT handle connected devices slipping into the
Inactive state very well. This is a concern, because devices can go
into the Inactive state on U1/U2 exit failure. However, the fix for
that case is too large for stable, so it will be submitted in a separate
patch.
This patch should be backported to kernels as old as 3.2, contain the
commit ID 75d7cf72ab "usbcore: refine warm
reset logic"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: John Covici <covici@ccs.covici.com>
Cc: stable@vger.kernel.org
The port reset code bails out early if the current connect status is
cleared (device disconnected). If we're issuing a hot reset, it may
also look at the link state before the reset is finished.
Section 10.14.2.6 of the USB 3.0 spec says that when a port enters the
Error state or Resetting state, the port connection bit retains the
value from the previous state. Therefore we can't trust it until the
reset finishes. Also, the xHCI spec section 4.19.1.2.5 says software
shall ignore the link state while the port is resetting, as it can be in
an unknown state.
The port state during reset is also unknown for USB 2.0 hubs. The hub
sends a reset signal by driving the bus into an SE0 state. This
overwhelms the "connect" signal from the device, so the port can't tell
whether anything is connected or not.
Fix the port reset code to ignore the port link state and current
connect bit until the reset finishes, and USB_PORT_STAT_RESET is
cleared.
Remove the check for USB_PORT_STAT_C_BH_RESET in the warm reset case,
because it's redundant. When the warm reset finishes, the port reset
bit will be cleared at the same time USB_PORT_STAT_C_BH_RESET is set.
Remove the now-redundant check for a cleared USB_PORT_STAT_RESET bit
in the code to deal with the finished reset.
This patch should be backported to all stable kernels.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
John's NEC 0.96 xHCI host controller needs a longer timeout for a warm
reset to complete. The logs show it takes 650ms to complete the warm
reset, so extend the hub reset timeout to 800ms to be on the safe side.
This commit should be backported to kernels as old as 3.2, that contain
the commit 75d7cf72ab "usbcore: refine
warm reset logic".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: John Covici <covici@ccs.covici.com>
Cc: stable@vger.kernel.org
If hot and warm reset fails, or a port remains in the Compliance Mode,
the USB core needs to be able to disable a USB 3.0 port. Unlike USB 2.0
ports, once the port is placed into the Disabled link state, it will not
report any new device connects. To get device connect notifications, we
need to put the link into the Disabled state, and then the RxDetect
state.
The xHCI driver needs to atomically clear all change bits on USB 3.0
port disable, so that we get Port Status Change Events for future port
changes. We could technically do this in the USB core instead of in the
xHCI roothub code, since the port state machine can't advance out of the
disabled state until we set the link state to RxDetect. However,
external USB 3.0 hubs don't need this code. They are level-triggered,
not edge-triggered like xHCI, so they will continue to send interrupt
events when any change bit is set. Therefore it doesn't make sense to
put this code in the USB core.
This patch is part of a series to fix several reports of infinite loops
on device enumeration failure. This includes John, when he boots with
a USB 3.0 device (Roseweil eusb3 enclosure) attached to his NEC 0.96
host controller. The fix requires warm reset support, so it does not
make sense to backport this patch to stable kernels without warm reset
support.
This patch should be backported to kernels as old as 3.2, contain the
commit ID 75d7cf72ab "usbcore: refine warm
reset logic"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: John Covici <covici@ccs.covici.com>
Cc: stable@vger.kernel.org
When the USB core finishes reseting a USB device, the xHCI driver sends
a Reset Device command to the host. The xHC then updates its internal
representation of the USB device to the 'Default' device state. If the
device was already in the Default state, the xHC will complete the
command with an error status.
If a device needs to be reset several times during enumeration, the
second reset will always fail because of the xHCI Reset Device command.
This can cause issues during enumeration.
For example, usb_reset_and_verify_device calls into hub_port_init in a
loop. Say that on the first call into hub_port_init, the device is
successfully reset, but doesn't respond to several set address control
transfers. Then the port will be disabled, but the udev will remain in
tact. usb_reset_and_verify_device will call into hub_port_init again.
On the second call into hub_port_init, the device will be reset, and the
xHCI driver will issue a Reset Device command. This command will fail
(because the device is already in the Default state), and
usb_reset_and_verify_device will fail. The port will be disabled, and
the device won't be able to enumerate.
Fix this by ignoring the return value of the HCD reset_device callback.
This commit should be backported to kernels as old as 3.2, that contain
the commit 75d7cf72ab "usbcore: refine
warm reset logic".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
USB 3.0 hubs and roothubs will automatically transition a failed hot
reset to a warm (BH) reset. In that case, the warm reset change bit
will be set, and the link state change bit may also be set. Change
hub_port_finish_reset to unconditionally clear those change bits for USB
3.0 hubs. If these bits are not cleared, we may lose port change events
from the roothub.
This commit should be backported to kernels as old as 3.2, that contain
the commit 75d7cf72ab "usbcore: refine
warm reset logic".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
A high speed control or bulk endpoint may have bInterval set to zero,
which means it does not NAK. If bInterval is non-zero, it means the
endpoint NAKs at a rate of 2^(bInterval - 1).
The xHCI code to compute the NAK interval does not handle the special
case of zero properly. The current code unconditionally subtracts one
from bInterval and uses it as an exponent. This causes a very large
bInterval to be used, and warning messages like these will be printed:
usb 1-1: ep 0x1 - rounding interval to 32768 microframes, ep desc says 0 microframes
This may cause the xHCI host hardware to reject the Configure Endpoint
command, which means the HS device will be unusable under xHCI ports.
This patch should be backported to kernels as old as 2.6.31, that contain
commit dfa49c4ad1 "USB: xhci - fix math in
xhci_get_endpoint_interval()".
Reported-by: Vincent Pelletier <plr.vincent@gmail.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The {read,write}s{b,w,l} operations are not defined by all architectures
and are being removed from the asm-generic/io.h interface.
This patch replaces the usage of these string functions in the musb
accessors with io{read,write}{8,16,32}_rep calls instead.
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The {read,write}s{b,w,l} operations are not defined by all architectures
and are being removed from the asm-generic/io.h interface.
This patch replaces the usage of these string functions in the tusb6010
accessors with io{read,write}{8,16,32}_rep calls instead.
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These devices are not available on other architectures, so
let's limit them to omap.
If the driver subsystem maintainers want to build test
system wide changes without building for each target,
it's easy to carry a test patch that just strips out the
depends entries from Kconfig files.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
This branch contains a largeish set of updates of power management and
clock setup. The bulk of it is for OMAP/AM33xx platforms, but also a
few around hotplug/suspend/resume on Exynos.
It includes a split-up of some of the OMAP clock data into separate
files which adds to the diffstat, but gross delta is fairly reasonable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=h2Qo
-----END PGP SIGNATURE-----
Merge tag 'pm-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC power management and clock changes from Olof Johansson:
"This branch contains a largeish set of updates of power management and
clock setup. The bulk of it is for OMAP/AM33xx platforms, but also a
few around hotplug/suspend/resume on Exynos.
It includes a split-up of some of the OMAP clock data into separate
files which adds to the diffstat, but gross delta is fairly reasonable."
* tag 'pm-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
watchdog: OMAP: fixup for ARM multiplatform support
ARM: EXYNOS: Add flush_cache_all in suspend finisher
ARM: EXYNOS: Remove scu_enable from cpuidle
ARM: EXYNOS: Fix soft reboot hang after suspend/resume
ARM: EXYNOS: Add support for rtc wakeup
ARM: EXYNOS: fix the hotplug for Cortex-A15
ARM: OMAP2+: omap_device: Correct resource handling for DT boot
ARM: OMAP2+: hwmod: Add possibility to count hwmod resources based on type
ARM: OMAP2+: hwmod: Add support for per hwmod/module context lost count
ARM: OMAP2+: PRM: initialize some PRM functions early
ARM: OMAP2+: voltage: fixup oscillator handling when CONFIG_PM=n
ARM: OMAP4: USB: power down MUSB PHY during boot
ARM: OMAP2+: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP2xxx: clock: drop obsolete clock data
ARM: OMAP2: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP3+: DPLL: drop !CONFIG_COMMON_CLK sections
ARM: AM33xx: clock: drop obsolete clock data
ARM: OMAP3xxx: clk: drop obsolete clock data
...
Continued device tree conversion and enablement across a number of
platforms; Kirkwood, tegra, i.MX, Exynos, zynq and a couple of other
smaller series as well.
ux500 has seen continued conversion for platforms. Several platforms have
seen pinctrl-via-devicetree conversions for simpler multiplatform. Tegra
is adding data for new devices/drivers, and Exynos has a bunch of new
bindings and devices added as well.
So, pretty much the same progression in the right direction as the last
few releases.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQySW7AAoJEIwa5zzehBx39xcP/jzEQOTOJdK4zJd1OjgrQoX/
WnhbGJT941RNjRjvDG6HmZzhpsRoE4q/zkjFEKoKELdikRW0hYoR+zPCGuB7XtN5
aF1ZQrTx4gHf4KE7doIB8slaWeOq8aG2TLFhylyy+cuaIpRK0NG0pAR0ZqWaoga9
tZFciqzplLeo50vZ+y+lVVsR40j/w29EjwPXhCV30//gGOYLyp/VDu5PRtrBdgh8
EgpcT2EWJwMCN/Upcao/q2JbQktPHPpSwnpaUAALYB20uD7k5jo7wtYE/+L9nn6B
bxcCDTMVmqzNTF+y0P16hDcs5jMLVjpI0xBiyZ1G6gShpggsSZCHY5ynjAtQ19se
r+2WrNfOR23k6arJuOUAQSEnLdx0T5SlW6CJeFEofKv4uoebxAbKUiNO4ShWskhd
nNptX1+L3hj3zpjGcEHmL6bd+nGtyMeoG9Yekcv1oZxdVcpKhFxh0s5PEJBEeXcN
M7aAWlWJkplV22Olqhpc/3INCweq6E+zBrBxZaUBW/JCzGrqBUGC0BULDPAkmC4J
CKL6IqIB73jGQ4OY14IaMU20GJrIGxZ7wzXOp4aw3OUpRlxsgurfyFQeIjUvVoZL
PJ8DRoAVwreVHvKfgZZVKpSAY7dwcWbxpWsYlrH3zWIC5vRJ0UFwsD0TpLJWd6Vi
XA8gQcJRWKGS8E5mRY39
=Rk9v
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree conversions and enablement from Olof Johansson:
"Continued device tree conversion and enablement across a number of
platforms; Kirkwood, tegra, i.MX, Exynos, zynq and a couple of other
smaller series as well.
ux500 has seen continued conversion for platforms. Several platforms
have seen pinctrl-via-devicetree conversions for simpler
multiplatform. Tegra is adding data for new devices/drivers, and
Exynos has a bunch of new bindings and devices added as well.
So, pretty much the same progression in the right direction as the
last few releases."
Fix up conflicts as per Olof.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (185 commits)
ARM: ux500: Rename dbx500 cpufreq code to be more generic
ARM: dts: add missing ux500 device trees
ARM: ux500: Stop registering the PCM driver from platform code
ARM: ux500: Move board specific GPIO info out to subordinate DTS files
ARM: ux500: Disable the MMCI gpio-regulator by default
ARM: Kirkwood: remove kirkwood_ehci_init() from new boards
ARM: Kirkwood: Add support LED of OpenBlocks A6
ARM: Kirkwood: Convert to EHCI via DT for OpenBlocks A6
ARM: kirkwood: Add NAND partiton map for OpenBlocks A6
ARM: kirkwood: Add support second I2C bus and RTC on OpenBlocks A6
ARM: kirkwood: Add support DT of second I2C bus
ARM: kirkwood: Convert mplcec4 board to pinctrl
ARM: Kirkwood: Convert km_kirkwood to pinctrl
ARM: Kirkwood: support 98DX412x kirkwoods with pinctrl
ARM: Kirkwood: Convert IX2-200 to pinctrl.
ARM: Kirkwood: Convert lsxl boards to pinctrl.
ARM: Kirkwood: Convert ib62x0 to pinctrl.
ARM: Kirkwood: Convert GoFlex Net to pinctrl.
ARM: Kirkwood: Convert dreamplug to pinctrl.
ARM: Kirkwood: Convert dockstar to pinctrl.
...
Commit 5c8a86e10a (usb: musb: drop unneeded
musb_debug trickery) erroneously removed '\n' from the driver's banner.
Concatenate all the banner substrings while adding it back...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Felipe Balbi <balbi@ti.com>
When a device is switched off by software, gserial_cleanup will
be called, and switch off will be blocked in this function
because wake_up_interruptible() in gs_close() can not wake_up
the wait_event() in gserial_cleanup(), it should be changed to
wake_up() to match the wait_event().
Signed-off-by: Haipeng YU <haipeng.yu@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In the error handling case of tcm_usbg_drop_nexus(), the error code
is assigned to 'ret', but it is ignored. We'd better return 'ret'
instead of always return 0.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
"54db6ee ARM: OMAP2+: Introduce local usb.h" moved control module bit
definitions from plat/usb.h (which dsps glue was using) to a local
header in mach-omap2. And in parallel,
"c68bb4c usb: musb: dsps: control module handling (quirk)" added
control module handling capability to dsps glue driver that used
those control module bit definitions.
Integration of above two changes would cause build error in musb dsps
glue driver (they go through different trees upstream) as is seen now
in linux-next. Fix it by adding necessary definitions in dsps glue
driver.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we do have endpoints named like "ep-a" then bEndpointAddress is
counted internally by the gadget framework.
If we do have endpoints named like "ep-1" then bEndpointAddress is
assigned from the digit after "ep-".
If we do have both, then it is likely that after we used up the
"generic" endpoints we will use the digits and thus assign one
bEndpointAddress to multiple endpoints.
This theory can be proofed by using the completely enabled g_multi.
Without this patch, the mass storage won't enumerate and times out
because it shares endpoints with RNDIS.
This patch also adds fills up the endpoints list so we have in total
endpoints 1 to 15 in + out available while some of them are restricted
to certain types like BULK or ISO. Without this change the nokia gadget
won't load because the system does not provide enough (BULK) endpoints
but it did before ep-a - ep-f were removed.
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
the clock common driver changes, and arch-mmp will make use of
the common clock driver instead of its own.
So for enable clock.
first prepare the clock
then enable the clock.
for disable clock
first disable the clock
then unprepare the clock
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
usbhsh_ureq_free() free ureq which includes ubshs_pkt.
But current driver used usbhs_pkt after freed ureq.
This patch fixup this bug.
Special thanks to Chen
Reported-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Current usbhsg_ep_disable() didn't care
uep->pipe and pipe->mod_private variable which is used on usbhsg_ep_enable().
It breaks renesas_usbhs gadget when resume.
This patch fixes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since hsotg object is allocated using devm_kzalloc() API, there is no
need to free this explicitly. But we need to keep the release API to
prevent warnings.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
the clock common driver changes, and arch-mmp will make use of
the common clock driver instead of its own.
So for enable clock.
first prepare the clock
then enable the clock.
for disable clock
first disable the clock
then unprepare the clock
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
the clock common driver changes, and arch-mmp will make use of
the common clock driver instead of its own.
So for enable clock.
first prepare the clock
then enable the clock.
for disable clock
first disable the clock
then unprepare the clock
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB_GADGET_FSL_USB2 has been changed to USB_FSL_USB2 by commit
193ab2a607 (usb: gadget: allow
multiple gadgets to be built). But old USB_GADGET_FSL_USB2 is
still listed as dependency for fsl_otg driver, so the driver
cannot be selected in the configuration currently. Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Current driver always initialized uep->pipe to NULL on usbhsg_try_start().
But it breaks relationship with
usb_ep_ops :: enable/disable functions when suspend/resume.
This patch solved this issue by initializing uep->pipe on probe()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As with dwc_readl/writel, the global registers are specified as
offsets starting from the beginning of the xHCI address space,
but the memory region pointed to by dwc->regs already maps to
the start of the global addresses. Fix by offsetting each of the
regs relative to DWC3_GLOBALS_REGS_START.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Cleanup patches for various ARM platforms and some of their associated
drivers. There's also a branch in here that enables Freescale i.MX to be
part of the multiplatform support -- the first "big" SoC that is moved
over (more multiplatform work comes in a separate branch later during
the merge window).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=zfPd
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups on various subarchitectures from Olof Johansson:
"Cleanup patches for various ARM platforms and some of their associated
drivers. There's also a branch in here that enables Freescale i.MX to
be part of the multiplatform support -- the first "big" SoC that is
moved over (more multiplatform work comes in a separate branch later
during the merge window)."
Conflicts fixed as per Olof, including a silent semantic one in
arch/arm/mach-omap2/board-generic.c (omap_prcm_restart() was renamed to
omap3xxx_restart(), and a new user of the old name was added).
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (189 commits)
ARM: omap: fix typo on timer cleanup
ARM: EXYNOS: Remove unused regs-mem.h file
ARM: EXYNOS: Remove unused non-dt support for dwmci controller
ARM: Kirkwood: Use hw_pci.ops instead of hw_pci.scan
ARM: OMAP3: cm-t3517: use GPTIMER for system clock
ARM: OMAP2+: timer: remove CONFIG_OMAP_32K_TIMER
ARM: SAMSUNG: use devm_ functions for ADC driver
ARM: EXYNOS: no duplicate mask/unmask in eint0_15
ARM: S3C24XX: SPI clock channel setup is fixed for S3C2443
ARM: EXYNOS: Remove i2c0 resource information and setting of device names
ARM: Kirkwood: checkpatch cleanups
ARM: Kirkwood: Fix sparse warnings.
ARM: Kirkwood: Remove unused includes
ARM: kirkwood: cleanup lsxl board includes
ARM: integrator: use BUG_ON where possible
ARM: integrator: push down SC dependencies
ARM: integrator: delete static UART1 mapping
ARM: integrator: delete SC mapping on the CP
ARM: integrator: remove static CP syscon mapping
ARM: integrator: remove static AP syscon mapping
...
This is a collection of header file cleanups, mostly for OMAP and AT91,
that keeps moving the platforms in the direction of multiplatform by
removing the need for mach-dependent header files used in drivers and
other places.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=aggA
-----END PGP SIGNATURE-----
Merge tag 'headers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC Header cleanups from Olof Johansson:
"This is a collection of header file cleanups, mostly for OMAP and
AT91, that keeps moving the platforms in the direction of
multiplatform by removing the need for mach-dependent header files
used in drivers and other places."
Fix up mostly trivial conflicts as per Olof.
* tag 'headers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (106 commits)
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
atmel: move ATMEL_MAX_UART to platform_data/atmel.h
ARM: OMAP: Remove omap_init_consistent_dma_size()
arm: at91: move at91rm9200 rtc header in drivers/rtc
arm: at91: move reset controller header to arm/arm/mach-at91
arm: at91: move pit define to the driver
arm: at91: move at91_shdwc.h to arch/arm/mach-at91
arm: at91: move board header to arch/arm/mach-at91
arn: at91: move at91_tc.h to arch/arm/mach-at91
arm: at91 move at91_aic.h to arch/arm/mach-at91
arm: at91 move board.h to arch/arm/mach-at91
arm: at91: move platfarm_data to include/linux/platform_data/atmel.h
arm: at91: drop machine defconfig
ARM: OMAP: Remove NEED_MACH_GPIO_H
ARM: OMAP: Remove unnecessary mach and plat includes
...
Pull ARM updates from Russell King:
"Here's the updates for ARM for this merge window, which cover quite a
variety of areas.
There's a bunch of patch series from Will tackling various bugs like
the PROT_NONE handling, ASID allocation, cluster boot protocol and
ASID TLB tagging updates.
We move to a build-time sorted exception table rather than doing the
sorting at run-time, add support for the secure computing filter, and
some updates to the perf code. We also have sorted out the placement
of some headers, fixed some build warnings, fixed some hotplug
problems with the per-cpu TWD code."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (73 commits)
ARM: 7594/1: Add .smp entry for REALVIEW_EB
ARM: 7599/1: head: Remove boot-time HYP mode check for v5 and below
ARM: 7598/1: net: bpf_jit_32: fix sp-relative load/stores offsets.
ARM: 7595/1: syscall: rework ordering in syscall_trace_exit
ARM: 7596/1: mmci: replace readsl/writesl with ioread32_rep/iowrite32_rep
ARM: 7597/1: net: bpf_jit_32: fix kzalloc gfp/size mismatch.
ARM: 7593/1: nommu: do not enable DCACHE_WORD_ACCESS when !CONFIG_MMU
ARM: 7592/1: nommu: prevent generation of kernel unaligned memory accesses
ARM: 7591/1: nommu: Enable the strict alignment (CR_A) bit only if ARCH < v6
ARM: 7590/1: /proc/interrupts: limit the display of IPIs to online CPUs only
ARM: 7587/1: implement optimized percpu variable access
ARM: 7589/1: integrator: pass the lm resource to amba
ARM: 7588/1: amba: create a resource parent registrator
ARM: 7582/2: rename kvm_seq to vmalloc_seq so to avoid confusion with KVM
ARM: 7585/1: kernel: fix nr_cpu_ids check in DT logical map init
ARM: 7584/1: perf: fix link error when CONFIG_HW_PERF_EVENTS is not selected
ARM: gic: use a private mapping for CPU target interfaces
ARM: kernel: add logical mappings look-up
ARM: kernel: add cpu logical map DT init in setup_arch
ARM: kernel: add device tree init map function
...
Here's the big set of USB patches for 3.8-rc1.
Lots of USB host driver cleanups in here, and a bit of a reorg of the
EHCI driver to make it easier for the different EHCI platform drivers to
all work together nicer, which was a reduction in overall code. We also
deleted some unused firmware files, and got rid of the very old
file_storage usb gadget driver that had been broken for a long time.
This means we ended up removing way more code than added, always a nice
thing to see:
310 files changed, 3028 insertions(+), 10754 deletions(-)
Other than that, the usual set of new device ids, driver fixes, gadget
driver and controller updates and the like.
All of these have been in the linux-next tree for a number of weeks.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHhIYACgkQMUfUDdst+yk9gACgsZYgMtbrqdbhbjbYkfO7nYkB
iegAoIvj3qwe33TbZ8OJnIkaWcMiT8CW
=u6Bf
-----END PGP SIGNATURE-----
Merge tag 'usb-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big set of USB patches for 3.8-rc1.
Lots of USB host driver cleanups in here, and a bit of a reorg of the
EHCI driver to make it easier for the different EHCI platform drivers
to all work together nicer, which was a reduction in overall code. We
also deleted some unused firmware files, and got rid of the very old
file_storage usb gadget driver that had been broken for a long time.
This means we ended up removing way more code than added, always a
nice thing to see:
310 files changed, 3028 insertions(+), 10754 deletions(-)
Other than that, the usual set of new device ids, driver fixes, gadget
driver and controller updates and the like.
All of these have been in the linux-next tree for a number of weeks.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (228 commits)
USB: mark uas driver as BROKEN
xhci: Add Lynx Point LP to list of Intel switchable hosts
uwb: fix uwb_dev_unlock() missed at an error path in uwb_rc_cmd_async()
USB: ftdi_sio: Add support for Newport AGILIS motor drivers
MAINTAINERS: remove drivers/block/ub.c
USB: chipidea: fix use after free bug
ezusb: add dependency to USB
usb: ftdi_sio: fixup BeagleBone A5+ quirk
USB: cp210x: add Virtenio Preon32 device id
usb: storage: remove redundant memset() in usb_probe_stor1()
USB: option: blacklist network interface on Huawei E173
USB: OHCI: workaround for hardware bug: retired TDs not added to the Done Queue
USB: add new zte 3g-dongle's pid to option.c
USB: opticon: switch to generic read implementation
USB: opticon: refactor reab-urb processing
USB: opticon: use usb-serial bulk-in urb
USB: opticon: increase bulk-in size
USB: opticon: use port as urb context
USB: opticon: pass port to get_serial_info
USB: opticon: make private data port specific
...
Here's the big tty/serial tree set of changes for 3.8-rc1.
Contained in here is a bunch more reworks of the tty port layer from Jiri and
bugfixes from Alan, along with a number of other tty and serial driver updates
by the various driver authors.
Also, Jiri has been coerced^Wconvinced to be the co-maintainer of the TTY
layer, which is much appreciated by me.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHhgwACgkQMUfUDdst+ynI6wCcC+YeBwncnoWHvwLAJOwAZpUL
bysAn28o780/lOsTzp3P1Qcjvo69nldo
=hN/g
-----END PGP SIGNATURE-----
Merge tag 'tty-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY/Serial merge from Greg Kroah-Hartman:
"Here's the big tty/serial tree set of changes for 3.8-rc1.
Contained in here is a bunch more reworks of the tty port layer from
Jiri and bugfixes from Alan, along with a number of other tty and
serial driver updates by the various driver authors.
Also, Jiri has been coerced^Wconvinced to be the co-maintainer of the
TTY layer, which is much appreciated by me.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up some trivial conflicts in the staging tree, due to the fwserial
driver having come in both ways (but fixed up a bit in the serial tree),
and the ioctl handling in the dgrp driver having been done slightly
differently (staging tree got that one right, and removed both
TIOCGSOFTCAR and TIOCSSOFTCAR).
* tag 'tty-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (146 commits)
staging: sb105x: fix potential NULL pointer dereference in mp_chars_in_buffer()
staging/fwserial: Remove superfluous free
staging/fwserial: Use WARN_ONCE when port table is corrupted
staging/fwserial: Destruct embedded tty_port on teardown
staging/fwserial: Fix build breakage when !CONFIG_BUG
staging: fwserial: Add TTY-over-Firewire serial driver
drivers/tty/serial/serial_core.c: clean up HIGH_BITS_OFFSET usage
staging: dgrp: dgrp_tty.c: Audit the return values of get/put_user()
staging: dgrp: dgrp_tty.c: Remove the TIOCSSOFTCAR ioctl handler from dgrp driver
serial: ifx6x60: Add modem power off function in the platform reboot process
serial: mxs-auart: unmap the scatter list before we copy the data
serial: mxs-auart: disable the Receive Timeout Interrupt when DMA is enabled
serial: max310x: Setup missing "can_sleep" field for GPIO
tty/serial: fix ifx6x60.c declaration warning
serial: samsung: add devicetree properties for non-Exynos SoCs
serial: samsung: fix potential soft lockup during uart write
tty: vt: Remove redundant null check before kfree.
tty/8250 Add check for pci_ioremap_bar failure
tty/8250 Add support for Commtech's Fastcom Async-335 and Fastcom Async-PCIe cards
tty/8250 Add XR17D15x devices to the exar_handle_irq override
...
enabled. Unfortunately the DMA header patch had to be redone
to avoid adding new multiplatform specific include paths, the
other patches are just trivial compile fixes.
Note that this does not yet contain the necessary Kconfig
changes as we are still waiting for some drivers to get
fixed up first.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=w+UN
-----END PGP SIGNATURE-----
Merge tag 'tags/omap-for-v3.8/cleanup-multiplatform-no-clock-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/pm2
From Tony Lindgren:
Remaining patches to allow omap2+ to build with multiplatform
enabled. Unfortunately the DMA header patch had to be redone
to avoid adding new multiplatform specific include paths, the
other patches are just trivial compile fixes.
Note that this does not yet contain the necessary Kconfig
changes as we are still waiting for some drivers to get
fixed up first.
* tag 'tags/omap-for-v3.8/cleanup-multiplatform-no-clock-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
watchdog: OMAP: fixup for ARM multiplatform support
Conflicts due to surrounding changes in:
arch/arm/mach-omap2/omap_hwmod_2420_data.c
arch/arm/mach-omap2/omap_hwmod_2430_data.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Based on earlier discussions[1] we attempted to find a suitable
location for the omap DMA header in commit 2b6c4e73 (ARM: OMAP:
DMA: Move plat/dma.h to plat-omap/dma-omap.h) until the conversion
to dmaengine is complete.
Unfortunately that was before I was able to try to test compile
of the ARM multiplatform builds for omap2+, and the end result
was not very good.
So I'm creating yet another all over the place patch to cut the
last dependency for building omap2+ for ARM multiplatform. After
this, we have finally removed the driver dependencies to the
arch/arm code, except for few drivers that are being worked on.
The other option was to make the <plat-omap/dma-omap.h> path
to work, but we'd have to add some new header directory to for
multiplatform builds.
Or we would have to manually include arch/arm/plat-omap/include
again from arch/arm/Makefile for omap2+.
Neither of these alternatives sound appealing as they will
likely lead addition of various other headers exposed to the
drivers, which we want to avoid for the multiplatform kernels.
Since we already have a minimal include/linux/omap-dma.h,
let's just use that instead and add a note to it to not
use the custom omap DMA functions any longer where possible.
Note that converting omap DMA to dmaengine depends on
dmaengine supporting automatically incrementing the FIFO
address at the device end, and converting all the remaining
legacy drivers. So it's going to be few more merge windows.
[1] https://patchwork.kernel.org/patch/1519591/#
cc: Russell King <linux@arm.linux.org.uk>
cc: Kevin Hilman <khilman@ti.com>
cc: "Benoît Cousson" <b-cousson@ti.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Vinod Koul <vinod.koul@intel.com>
cc: Dan Williams <djbw@fb.com>
cc: Mauro Carvalho Chehab <mchehab@infradead.org>
cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
cc: David Woodhouse <dwmw2@infradead.org>
cc: Kyungmin Park <kyungmin.park@samsung.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
cc: Hans Verkuil <hans.verkuil@cisco.com>
cc: Vaibhav Hiremath <hvaibhav@ti.com>
cc: Lokesh Vutla <lokeshvutla@ti.com>
cc: Rusty Russell <rusty@rustcorp.com.au>
cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
cc: Afzal Mohammed <afzal@ti.com>
cc: linux-crypto@vger.kernel.org
cc: linux-media@vger.kernel.org
cc: linux-mtd@lists.infradead.org
cc: linux-usb@vger.kernel.org
cc: linux-fbdev@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
By Lee Jones (42) and others
via Olof Johansson (13) and others
* next/dt: (249 commits)
ARM: ux500: Rename dbx500 cpufreq code to be more generic
ARM: dts: add missing ux500 device trees
ARM: ux500: Stop registering the PCM driver from platform code
ARM: ux500: Move board specific GPIO info out to subordinate DTS files
ARM: ux500: Disable the MMCI gpio-regulator by default
ARM: Kirkwood: remove kirkwood_ehci_init() from new boards
ARM: Kirkwood: Add support LED of OpenBlocks A6
ARM: Kirkwood: Convert to EHCI via DT for OpenBlocks A6
ARM: kirkwood: Add NAND partiton map for OpenBlocks A6
ARM: kirkwood: Add support second I2C bus and RTC on OpenBlocks A6
ARM: kirkwood: Add support DT of second I2C bus
ARM: kirkwood: Convert mplcec4 board to pinctrl
ARM: Kirkwood: Convert km_kirkwood to pinctrl
ARM: Kirkwood: support 98DX412x kirkwoods with pinctrl
ARM: Kirkwood: Convert IX2-200 to pinctrl.
ARM: Kirkwood: Convert lsxl boards to pinctrl.
ARM: Kirkwood: Convert ib62x0 to pinctrl.
ARM: Kirkwood: Convert GoFlex Net to pinctrl.
ARM: Kirkwood: Convert dreamplug to pinctrl.
ARM: Kirkwood: Convert dockstar to pinctrl.
...
As reported https://bugzilla.kernel.org/show_bug.cgi?id=51031, the UAS
driver causes problems and has been asked to be not built into any of
the major distributions. To prevent users from running into problems
with it, and for distros that were not notified, just mark the whole
thing as broken.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Like Lynx Point, Lynx Point LP is also switchable. See
1c12443ab8 for more details.
This patch should be backported to stable kernels as old as 3.0,
that contain commit 69e848c209
"Intel xhci: Support EHCI/xHCI port switching."
Signed-off-by: Russell Webb <russell.webb@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The Newport AGILIS model AG-UC8 compact piezo motor controller
(http://search.newport.com/?q=*&x2=sku&q2=AG-UC8)
is yet another device using an FTDI USB-to-serial chip. It works
fine with the ftdi_sio driver when adding
options ftdi-sio product=0x3000 vendor=0x104d
to modprobe.d. udevadm reports "Newport" as the manufacturer,
and "Agilis" as the product name.
Signed-off-by: Martin Teichmann <lkb.teichmann@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointer to a platform_device struct must not be dereferenced after
the device has been unregistered.
This bug produces a crash when unloading the ci13xxx kernel module
compiled with CONFIG_PAGE_POISONING enabled.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Cc: stable <stable@vger.kernel.org> # 3.6
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes an error during modpost, when ezusb is built into the kernel
while USB is built as module.
Signed-off-by: René Bürgel <rene.buergel@sohard.de>
Cc: stable <stable@vger.kernel.org>
--
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BeagleBone A5+ devices ended up getting shipped with the
'BeagleBone/XDS100V2' product string, and not XDS100 like it
was agreed, so adjust the quirk to match.
For details, see the thread on the beagle list:
https://groups.google.com/forum/#!msg/beagleboard/zrFPew9_Wvo/ibWr1-eE8JwJ
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
scsi_host_alloc() will zero our private data, no need to memset it.
Signed-off-by: Yan Hong <clouds.yan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Huawei E173 will normally appear as 12d1:1436 in Linux. But
the modem has another mode with different device ID and a slightly
different set of descriptors. This is the mode used by Windows like
this:
3Modem: USB\VID_12D1&PID_140C&MI_00\6&3A1D2012&0&0000
Networkcard: USB\VID_12D1&PID_140C&MI_01\6&3A1D2012&0&0001
Appli.Inter: USB\VID_12D1&PID_140C&MI_02\6&3A1D2012&0&0002
PC UI Inter: USB\VID_12D1&PID_140C&MI_03\6&3A1D2012&0&0003
All interfaces have the same ff/ff/ff class codes in this mode.
Blacklisting the network interface to allow it to be picked up by
the network driver.
Cc: stable <stable@vger.kernel.org>
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1636) is a partial workaround for a hardware bug
affecting OHCI controllers by NVIDIA at least, maybe others too. When
the controller retires a Transfer Descriptor, it is supposed to add
the TD onto the Done Queue. But sometimes this doesn't happen, with
the result that ohci-hcd never realizes the corresponding transfer has
finished. Symptoms can vary; a typical result is that USB audio stops
working after a while.
The patch works around the problem by recognizing that TDs are always
processed in order. Therefore, if a later TD is found on the Done
Queue than all the earlier TDs for the same endpoint must be finished
as well.
Unfortunately this won't solve the problem in cases where the missing
TD is the last one in the endpoint's queue. A complete fix would
require a signficant amount of change to the driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Oliver Neukum <oneukum@suse.de>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- ehci-orion dt binding
- gpio-poweroff
- use dt regulators
- move mpp to DT/pinctrl
Depends on:
- orion/boards
- merge conflicts
- keep all 'select's in Kconfig
- remove all #includes in board-*.c
- pinctrl/devel up to:
- 06763c7 pinctrl: mvebu: move to its own directory
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQsEfdAAoJEAi3KVZQDZAeBd8IAIAkBGIJyUJSmQJEWkZ/9ezq
UOLec1t/TnLhAQ1Sk8g4C41wmHKYNqmZSVaAXC+QP6Yw+Gdhlw+V6YBjOYDzA7Y4
k8ljw3SFbvS+AIx0qK26j6Tf6En2H5lMXsdlKoarCV+G+MxAHsQO7jL6y7BFwTlX
QnwJFz+NRzMFxaPiCS+43oZuxIIzkHe8wKMb0y7nSiNQYUUv8TdKvyK+ekFuszOp
v6uo/MI1p1/xdUxDbEKxOwmUjAy7x+t0LUFi1dsWuiDHdrG+BVT4NkJuFaD8Ui13
VoUD1ogyWHQZV2hq0dfj+9Hed5NEgl6toAzGN9LPLmsuVUXCnB2CdBprhuDv5F8=
=yaX1
-----END PGP SIGNATURE-----
Merge tag 'orion_dt_for_3.8' of git://git.infradead.org/users/jcooper/linux into next/dt
From Jason Cooper:
orion dt for v3.8
- ehci-orion dt binding
- gpio-poweroff
- use dt regulators
- move mpp to DT/pinctrl
Depends on:
- orion/boards
- merge conflicts
- keep all 'select's in Kconfig
- remove all #includes in board-*.c
- pinctrl/devel up to:
- 06763c7 pinctrl: mvebu: move to its own directory
* tag 'orion_dt_for_3.8' of git://git.infradead.org/users/jcooper/linux: (211 commits)
ARM: Kirkwood: remove kirkwood_ehci_init() from new boards
ARM: Kirkwood: Add support LED of OpenBlocks A6
ARM: Kirkwood: Convert to EHCI via DT for OpenBlocks A6
ARM: kirkwood: Add NAND partiton map for OpenBlocks A6
ARM: kirkwood: Add support second I2C bus and RTC on OpenBlocks A6
ARM: kirkwood: Add support DT of second I2C bus
ARM: kirkwood: Convert mplcec4 board to pinctrl
ARM: Kirkwood: Convert km_kirkwood to pinctrl
ARM: Kirkwood: support 98DX412x kirkwoods with pinctrl
ARM: Kirkwood: Convert IX2-200 to pinctrl.
ARM: Kirkwood: Convert lsxl boards to pinctrl.
ARM: Kirkwood: Convert ib62x0 to pinctrl.
ARM: Kirkwood: Convert GoFlex Net to pinctrl.
ARM: Kirkwood: Convert dreamplug to pinctrl.
ARM: Kirkwood: Convert dockstar to pinctrl.
ARM: Kirkwood: Convert dnskw to pinctrl
ARM: Kirkwood: Convert iConnect to pinctrl.
ARM: Kirkwood: Convert TS219 to pinctrl.
ARM: Kirkwood: Add DTSI files for pinctrl
ARM: Kirkwood: Make use of mvebu pincltl and gpio drivers
...
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQss0FAAoJEHm+PkMAQRiG6cEH/An3PYsWBBy27tzoLyVfJKF1
3m3vR8HS2tnHg6erxms+738jos59vrWXV0Ygnvw0DHbGR0HNb4rkwce/KXu/jgOD
MRYNYhlhMFJTEUFrSrcwKITrAV3kVPWXxPXgAR6Gzpr6NPKKM9TBzEv0ze56TFYz
asOxqeBcPSS7aFZlkoNsy1wG4l0Quo5ke8VZIxo9Me5qlqubAoZ6pING4wAGXqeE
tf81CevSdpe0nqr8/dlYyCvLjrurgpJQczxRCBI3mP6kLWGfUCVzZmcu86PfT9b+
35zNJwDneIoN+D9bVDHy6mrq9uQdmhWnQuhv1joTPn6RDn1nyBRBd+A5qLxSov4=
=CPoy
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc7' into next/cleanup
Merging in mainline back to next/cleanup since it has collected a few
conflicts between fixes going upstream and some of the cleanup patches.
Git doesn't auto-resolve some of them, and they're mostly noise so let's
take care of it locally.
Conflicts are in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
arch/arm/plat-omap/i2c.c
drivers/video/omap2/dss/dss.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Based on previous work by Michael Walle and Jason Cooper.
Made their work actually work, which required added interrupt from DT
and auxdata, along with setting the dma_mask, which DT does not
currently do.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This is a set of four bug fixes. The isci one is an obvious thinko (using
request buffer instead of response buffer) which causes a command to fail.
The three others are DIF/DIX updates which are required because they're part
of a series of ten patches, the other seven of which went into the block layer
during the merge window meaning our current DIF/DIX implementation is broken
without these three.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQre/4AAoJEDeqqVYsXL0MrxwH/A+b3aYvany+ZPg+elAFBCFm
3qHJ2Bys+M/kTkb0Fqb/l1KQfGFjooqcozm6eTgIeZ67bK947pxzu4Txy4JmeXvC
cHQ2lzEzcIFjiyVqV0tQ/wxMCnHTeqDx1WX02aw3T6e5JxObe+gC1pAEoMz2unSk
kpsSvFKBfCBMY6bmbVY5c2vpFTgD4UKtBiKn/GKtLtIDvynRx0P5e7/TNawxUB64
QZ/tu3Z2Ov5g9VWod+LpQwjVI+bIBlBEV4Of+91zou64aocrqXtSoky+ae9mwfPy
7KLLZzz5Fzc5KwT8ynEECtU2iFQXJ/zXNDRh7gBffc0ReljpuouOvIgqdZEW8d0=
=kQyb
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of four bug fixes.
The isci one is an obvious thinko (using request buffer instead of
response buffer) which causes a command to fail.
The three others are DIF/DIX updates which are required because
they're part of a series of ten patches, the other seven of which went
into the block layer during the merge window meaning our current
DIF/DIX implementation is broken without these three.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] sd: Implement support for WRITE SAME
[SCSI] sd: Permit merged discard requests
[SCSI] Add a report opcode helper
[SCSI] isci: copy fis 0x34 response into proper buffer
Switch to the more efficient generic read implementation.
Note that the generic implementation is not required to hold the tty
port mutex during resume due to the read-urb free mask and write start
flag.
Note also that the generic resume implementation will call generic
write start if there is a bulk-out end-point, but that nothing will be
submitted as the write fifo is not used and is empty.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor and clean up read-urb processing.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the bulk-in urb provided by usb-serial core rather than allocating a
private one.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use 256 byte bulk-in buffers rather than double end-point sized ones.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use port rather than private data as urb context, as the latter may be
accessed as port data, and remove the port field from the private data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass port rather then private data to get_serial_info, which only used
the private data to access the port.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make private data port specific and move allocation and deallocation to
port_probe and port_remove.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove disconnect and its redundant read-urb kill which is already taken
care of in close.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move read-urb deallocation from disconnect to release.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove custom end-point iteration which has already been taken care of
by usb-serial core.
The first bulk-in endpoint found will be associated with the first port.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant usb-serial field from private data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant zero-initialisation of outstanding-urbs field in
kzalloced struct.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove usb-serial-device field from private data as it can be accessed
from the usb-serial-port structure.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use port rather than interface device to report port related errors and
debug information.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There no need to reinitialise the private urb at every open.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The private bulk in urb is set up at open and does not need to be
reinitialised at every resubmit.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'new_interfaces' should be freed to avoid memory leak.
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If param->length is zero, then this could lead to a divide by zero bug
later in the function when we do: size %= max;
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinitconst is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Li Yang <leoli@freescale.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinitdata is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A wide variety of device tree additions are made across many Tegra
boards:
* WiFi is supported on Seaboard, Ventana, and Cardhu.
* An I2C mux is added for Ventana, and Tamonten.
* SPI flash is added to Cardhu, and TrimSlice.
* Temperature sensors are added to Harmony, Tamonten, and Ventana.
* host1x (graphics/display controller) is added to the SoC include files.
* HDMI displays are enabled on Harmony, TrimSlice, Tamonten, Plutux, Tec,
and Whistler.
This pull request is based on tegra-for-3.8-soc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ytxh
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.8-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/dt
From Stephen Warren:
ARM: tegra: device tree changes
A wide variety of device tree additions are made across many Tegra
boards:
* WiFi is supported on Seaboard, Ventana, and Cardhu.
* An I2C mux is added for Ventana, and Tamonten.
* SPI flash is added to Cardhu, and TrimSlice.
* Temperature sensors are added to Harmony, Tamonten, and Ventana.
* host1x (graphics/display controller) is added to the SoC include files.
* HDMI displays are enabled on Harmony, TrimSlice, Tamonten, Plutux, Tec,
and Whistler.
This pull request is based on tegra-for-3.8-soc.
* tag 'tegra-for-3.8-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (47 commits)
ARM: tegra: whistler: enable HDMI port
ARM: tegra: tec: Enable HDMI output
ARM: tegra: plutux: Enable HDMI output
ARM: tegra: tamonten: Add host1x support
ARM: tegra: trimslice: enable HDMI port
ARM: tegra: harmony: enable HDMI port
ARM: tegra: Add Tegra30 host1x support
ARM: tegra: Add Tegra20 host1x support
ARM: tegra: trimslice: enable SPI flash
ARM: tegra: dts: add sflash controller dt entry
ARM: tegra: ventana: Add NCT1008 temperature sensor
ARM: tegra: tamonten: Add NCT1008 temperature sensor
ARM: tegra: harmony: Add ADT7641 temperature sensor
ARM: tegra: tec: Remove redundant DT properties
ARM: tegra: tamonten: Add DDC/PTA pinmux
ARM: tegra: dts: cardhu: enable SLINK4
ARM: tegra: dts: add slink controller dt entry
ARM: dt: tegra: ventana: define pinmux for ddc
ARM: dt: t30 cardhu: set pinmux and power for wlan
ARM: dt: t20 ventana: set pinmux and power for wlan
...
Various trivial cleanup changes of the Tegra code for 3.8.
Many of the changes simply remove useless #include statements, which
enable those headers to be removed or moved later, as work towards
multi-platform zImage support.
<mach/{iram,io}map.h> are moved up to arch/arm/mach-tegra to prevent
any new code outside mach-tegra from using them.
Finally, the regulator definitions in all board device tree files are
updated to use the new simpler syntax that was agreed upon.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=aH3p
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.8-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
From Stephen Warren:
ARM: tegra: cleanup for 3.8
Various trivial cleanup changes of the Tegra code for 3.8.
Many of the changes simply remove useless #include statements, which
enable those headers to be removed or moved later, as work towards
multi-platform zImage support.
<mach/{iram,io}map.h> are moved up to arch/arm/mach-tegra to prevent
any new code outside mach-tegra from using them.
Finally, the regulator definitions in all board device tree files are
updated to use the new simpler syntax that was agreed upon.
* tag 'tegra-for-3.8-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: move irammap.h to mach-tegra
ARM: tegra: move iomap.h to mach-tegra
ARM: tegra: remove <mach/dma.h>
ARM: tegra: move tegra-ahb.h out of arch/arm/mach-tegra/
ARM: tegra: remove unnecessary includes of <mach/*.h>
iommu: tegra: remove include of <mach/iomap.h>
staging: nvec: remove include of <mach/iomap.h>
crypto: tegra: remove include of <mach/clk.h>
ARM: tegra: update *.dts for regulator-compatible deprecation
usb: phy: tegra remove include of <mach/iomap.h>
usb: host: tegra remove include of <mach/iomap.h>
"Whether" is misspelled in various comments across the tree; this
fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This resolves a conflict with these files:
drivers/usb/early/ehci-dbgp.c
drivers/usb/host/ehci-ls1x.c
drivers/usb/host/ohci-xls.c
drivers/usb/musb/ux500.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=CFfP
-----END PGP SIGNATURE-----
Merge tag 'imx-dt' of git://git.pengutronix.de/git/imx/linux-2.6 into next/dt
From Sascha Hauer <s.hauer@pengutronix.de>:
ARM i.MX dt updates for 3.8
* tag 'imx-dt' of git://git.pengutronix.de/git/imx/linux-2.6:
Add device tree file for the armadeus apf27
ARM i.MX: Add Ka-Ro TX25 devicetree
ARM i.MX25: Add devicetree
ARM i.MX25: Add devicetree support
ARM i.MX25: Add missing clock gates
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here are some USB fixes for the 3.7 tree.
Nothing huge here, just a number of tiny bugfixes resolving issues that
have been found, and two reverts of patches that were found to have
caused problems.
All of these have been in linux-next already.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlCmRoUACgkQMUfUDdst+ynwAACg2if9XANSq4+GqdR7lSF5jCRO
hwMAoNh7XAM4GEXPB9m3rB395p9rHsN0
=31VS
-----END PGP SIGNATURE-----
Merge tag 'usb-3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are some USB fixes for the 3.7 tree.
Nothing huge here, just a number of tiny bugfixes resolving issues
that have been found, and two reverts of patches that were found to
have caused problems.
All of these have been in linux-next already.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
Revert "USB/host: Cleanup unneccessary irq disable code"
USB: option: add Alcatel X220/X500D USB IDs
USB: option: add Novatel E362 and Dell Wireless 5800 USB IDs
USB: keyspan: fix typo causing GPF on open
USB: fix build with XEN and EARLY_PRINTK_DBGP enabled but USB_SUPPORT disabled
USB: usb_wwan: fix bulk-urb allocation
usb: otg: Fix build errors if USB_MUSB_OMAP2PLUS is selected as module
usb: musb: ux500: fix 'musbid' undeclared error in ux500_remove()
Revert "usb: musb: use DMA mode 1 whenever possible"
commit 392142 moved event buffer allocation out of dwc3_core_init() but
event buffer allocation uses the cached copy of hwparams to determine
the number of event buffers and the caching is done in dwc3_core_init.
So moved dwc3_cache_hwparams function before dwc3_alloc_event_buffers so
that dwc3_alloc_event_buffers sees the correct number of event buffers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the PXA2xx/IXP4xx UDC header file into linux/platform_data as it
only contains a driver platform data structure.
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The old parameter "port" is useless for phy notify, as one usb
phy is only for one usb port. New parameter "speed" stands for
the device's speed which is on the port, this "speed" parameter
is needed at some platforms which will do some phy operations
according to device's speed.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Mike Thompson <mpthompson@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At commit 925aa46ba9, Richard Zhao
<richard.zhao@freescale.com> adds the phy notification callback
when port change occurs. In fact, this phy notification should
be added according to below rules:
1. Only set HW_USBPHY_CTRL.ENHOSTDISCONDETECT
during high speed host mode.
2. Do not set HW_USBPHY_CTRL.ENHOSTDISCONDETECT
during the reset and speed negotiation period.
3. Do not set HW_USBPHY_CTRL.ENHOSTDISCONDETECT
during host suspend/resume sequence.
Please refer: i.mx23RM(page: 413) for below rules.
http://www.freescale.com/files/dsp/doc/ref_manual/IMX23RM.pdf
Freescale i.MX SoC, i.mx23, i.mx28 and i.mx6(i.mx6SL does not
need to follow the 3rd rule) need to follow above rules.
Current code set connect notification (HW_USBPHY_CTRL.ENHOSTDISCONDETECT)
at hub_port_connect_change, it conflicts with above the 2th rule.
The correct notification setting method should be:
1. Set connect notify after the second bus reset.
2. Set disconnect notify after disconnection.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Mike Thompson <mpthompson@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As phy is working, re-init phy may cause unexpected results
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The real reason causes mx23 fail are:
- Calling mxs_phy_hw_init(mxs_phy) again at connection
- Error connect/disconnect nodity at hub.c
The coming patch will fix above two problems, Mike Thompson
tested his hardware works OK after commented out this delay
setting.
This reverts commit 363366cf61.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices (ex Nokia C7) simply don't respond at all when data is sent
to some of their USB interfaces. The data gets stuck in the TTYs queue
and sits there until close(2), which them blocks because closing_wait
defaults to 30 seconds (even though the fd is O_NONBLOCK). This is
rarely desired. Implement the standard mechanism to adjust closing_wait
and let applications handle it how they want to.
See also 02303f7337 for usb_wwan.c.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Aleksander Morgado <aleksander@gnu.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit "TTY: move tty buffers to tty_port", the tty buffers are
not freed in some drivers. This is because tty_port_destructor is not
called whenever a tty_port is freed. This was an assumption I counted
with but was unfortunately untrue. So fix the drivers to fulfil this
assumption.
To be sure, the TTY buffers (and later some stuff) are gone along with
the tty_port, we have to call tty_port_destroy at tear-down places.
This is mostly where the structure containing a tty_port is freed.
This patch does exactly that -- put tty_port_destroy at those places.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It looks like I've run into some inconsistency in the USB stack behavior.
The USB stack maintains, among others, two states for the attach
USB device: authorized and owned. Authorization state is accessible to
the user space code through correspondent sysfs files, the ownership
can be set by claiming the hub's port with ioctl call. Both state may
be set before the device is attached, by access the hub settings. When
the new device is attached, both authorization and ownership prevent
the kernel USB stack from setting the newly attached device
configuration, but when the device is authorized, the ownership state
is ignored. It looks like ignoring the ownership state on
authorization make the stack behavior inconsistent; it also prevents
the user space code from completely overriding configuration
selection, important for implementing workarounds for bugs in the
device configuration selection.
The following patch makes the stack behavior more consistent, by
moving ownership test into usb_choose_configuration - the later
function is used both by generic_probe and usb_authorize_device
Signed-off-by: Joseph Hindin <hindin@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To facilitate upcoming cleanup in twl stack.
No functional changes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
since commit b4036cc (usb: gadget: add
isochronous support to gadget zero), g_zero
has learned about isochronous transfers, which
allows us to use usbtest.ko to exercise
isochronous pipes.
All we need to do to enable that functionality
on usbtest.ko, is set the "iso" to 1 on
struct usbtest_info
Signed-off-by: Boyan Nedeltchev <boyan@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch frees SPEAr ehci/ohci drivers from tension of freeing resources :)
devm_* derivatives of multiple routines are used while allocating resources,
which would be freed automatically by kernel.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We used to get clk using con-id, but now we have device struct available for
these devices as they are probed using DT. And so must get clk using dev-id.
Signed-off-by: Amardeep Rai <amardeep.rai-ext@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit c73cee7 (USB: EHCI: remove ehci_port_power() routine), the
'ehci' variable is no longer used, so remove it and fix the following
build warning:
drivers/usb/host/ehci-mxc.c:41:19: warning: unused variable 'ehci' [-Wunused-variable]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Test for tegra and hcd in tegra_ehci_remove() look like potential
NULL pointer dereference, but in fact those tests are not needed,
so remove these pointless tests entirely.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement support for WRITE SAME(10) and WRITE SAME(16) in the SCSI disk
driver.
- We set the default maximum to 0xFFFF because there are several
devices out there that only support two-byte block counts even with
WRITE SAME(16). We only enable transfers bigger than 0xFFFF if the
device explicitly reports MAXIMUM WRITE SAME LENGTH in the BLOCK
LIMITS VPD.
- max_write_same_blocks can be overriden per-device basis in sysfs.
- The UNMAP discovery heuristics remain unchanged but the discard
limits are tweaked to match the "real" WRITE SAME commands.
- In the error handling logic we now distinguish between WRITE SAME
with and without UNMAP set.
The discovery process heuristics are:
- If the device reports a SCSI level of SPC-3 or greater we'll issue
READ SUPPORTED OPERATION CODES to find out whether WRITE SAME(16) is
supported. If that's the case we will use it.
- If the device supports the block limits VPD and reports a MAXIMUM
WRITE SAME LENGTH bigger than 0xFFFF we will use WRITE SAME(16).
- Otherwise we will use WRITE SAME(10) unless the target LBA is beyond
0xFFFFFFFF or the block count exceeds 0xFFFF.
- no_write_same is set for ATA, FireWire and USB.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The REPORT SUPPORTED OPERATION CODES command can be used to query
whether a given opcode is supported by a device. Add a helper function
that allows us to look up commands.
We only issue RSOC if the device reports compliance with SPC-3 or
later. But to err on the side of caution we disable the command for ATA,
FireWire and USB.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This reverts commit 73d4066055.
Martin Steigerwald reported that this change caused a hard lockup when
using USB if threadirqs are enabled. Thomas pointed out that this patch
is incorrect, and can cause problems. So revert it to get the
previously working functionality back.
Reported-by: Martin Steigerwald <Martin@lichtvoll.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Chuansheng Liu <chuansheng.liu@intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Dell 5800 appears to be a simple rebrand of the Novatel E362.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f79b2d0f (USB: keyspan: fix NULL-pointer dereferences and
memory leaks) had a small typo which made the driver use wrong
offsets when mapping serial port private data. This results in
in a GPF when the port is opened.
Reported-by: Richard <richjunk@pacbell.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This first patch serie start the cleanup of the header in mach
by moving all the platform data to include/linux/platform_data
and move the board header and drivers header next to them
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c5hx
-----END PGP SIGNATURE-----
Merge tag 'for-3.8-at91_header_clean' of git://github.com/at91linux/linux-at91 into next/headers
From Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
arm: at91: mach header cleanup
This first patch serie start the cleanup of the header in mach
by moving all the platform data to include/linux/platform_data
and move the board header and drivers header next to them
* tag 'for-3.8-at91_header_clean' of git://github.com/at91linux/linux-at91:
arm: at91: move at91rm9200 rtc header in drivers/rtc
arm: at91: move reset controller header to arm/arm/mach-at91
arm: at91: move pit define to the driver
arm: at91: move at91_shdwc.h to arch/arm/mach-at91
arm: at91: move board header to arch/arm/mach-at91
arn: at91: move at91_tc.h to arch/arm/mach-at91
arm: at91 move at91_aic.h to arch/arm/mach-at91
arm: at91 move board.h to arch/arm/mach-at91
arm: at91: move platfarm_data to include/linux/platform_data/atmel.h
arm: at91: drop machine defconfig
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
that check will have to be done by all users
of xhci_suspend() so it sounds a lot better to
move the check to xhci_suspend() in order to
avoid code duplication.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This minor patch creates a more stricter conditional for the Z1 sytems for applying
the Compliance Mode Patch, this to avoid the quirk to be applied to models that
contain a "Z1" in their dmi product string but are different from Z1 systems.
This patch should be backported to stable kernels as old as 3.2, that
contain the commit 71c731a296 "usb: host:
xhci: Fix Compliance Mode on SN65LVPE502CP Hardware"
Signed-off-by: Alexis R. Cortes <alexis.cortes@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
xhci_alloc_segments_for_ring() builds a list of xhci_segments and links
the tail to head at the end (forming a ring). When it bails out for OOM
reasons half-way through, it tries to destroy its half-built list with
xhci_free_segments_for_ring(), even though it is not a ring yet. This
causes a null-pointer dereference upon hitting the last element.
Furthermore, one of its callers (xhci_ring_alloc()) mistakenly believes
the output parameters to be valid upon this kind of OOM failure, and
calls xhci_ring_free() on them. Since the (incomplete) list/ring should
already be destroyed in that case, this would lead to a use after free.
This patch fixes those issues by having xhci_alloc_segments_for_ring()
destroy its half-built, non-circular list manually and destroying the
invalid struct xhci_ring in xhci_ring_alloc() with a plain kfree().
This patch should be backported to kernels as old as 2.6.31, that
contains the commit 0ebbab3742 "USB: xhci:
Ring allocation and initialization."
A separate patch will need to be developed for kernels older than 3.4,
since the ring allocation code was refactored in that kernel.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The xHCI 1.0 specification made a change to the TD Size field in TRBs.
The value is now the number of packets that remain to be sent in the TD,
not including this TRB. The TD Size value for the last TRB in a TD must
always be zero.
The xHCI function xhci_v1_0_td_remainder() attempts to calculate this,
but it gets it wrong. First, it erroneously reuses the old
xhci_td_remainder function, which will right shift the value by 10. The
xHCI 1.0 spec as of June 2011 says nothing about right shifting by 10.
Second, it does not set the TD size for the last TRB in a TD to zero.
Third, it uses roundup instead of DIV_ROUND_UP. The total packet count
is supposed to be the total number of bytes in this TD, divided by the
max packet size, rounded up. DIV_ROUND_UP is the right function to use
in that case.
With the old code, a TD on an endpoint with max packet size 1024 would
be set up like so:
TRB 1, TRB length = 600 bytes, TD size = 0
TRB 1, TRB length = 200 bytes, TD size = 0
TRB 1, TRB length = 100 bytes, TD size = 0
With the new code, the TD would be set up like this:
TRB 1, TRB length = 600 bytes, TD size = 1
TRB 1, TRB length = 200 bytes, TD size = 1
TRB 1, TRB length = 100 bytes, TD size = 0
This commit should be backported to kernels as old as 3.0, that contain
the commit 4da6e6f247 "xhci 1.0: Update TD
size field format."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Chintan Mehta <chintan.mehta@sibridgetech.com>
Reported-by: Shimmer Huang <shimmering.h@gmail.com>
Tested-by: Bhavik Kothari <bhavik.kothari@sibridgetech.com>
Tested-by: Shimmer Huang <shimmering.h@gmail.com>
Cc: stable@vger.kernel.org
David reports that at drivers/usb/host/xhci.c:2257:
static bool xhci_is_sync_in_ep(unsigned int ep_type)
{
return (ep_type == ISOC_IN_EP || ep_type != INT_IN_EP);
}
The static analyser cppcheck says
[linux-3.7-rc2/drivers/usb/host/xhci.c:2257]: (style) Redundant condition: If ep_type == 5, the comparison ep_type != 7 is always true.
Maybe the original programmer intention was something like
static bool xhci_is_sync_in_ep(unsigned int ep_type)
{
return (ep_type == ISOC_IN_EP || ep_type == INT_IN_EP);
}
Fix this.
This patch should be backported to stable kernels as old as 3.2, that
contain the commit 2b69899934 "xhci: USB
3.0 BW checking."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: stable@vger.kernel.org
Non-static xHCI driver symbols should start with the "xhci_" prefix, in
order to avoid namespace pollution. Rename the "handshake" function to
"xhci_handshake".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Ben Hutchings <ben@decadent.org.uk>
This patch (as1633) changes slightly the way usbcore handled
submissions of URBs that are already active. It will now return
-EBUSY rather than -EINVAL, and it will call WARN_ONCE to draw
people's attention to the bug.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1632b) fixes a bug in ehci-hcd. The USB core uses
urb->hcpriv to determine whether or not an URB is active; host
controller drivers are supposed to set this pointer to a non-NULL
value when an URB is queued. However ehci-hcd sets it to NULL for
isochronous URBs, which defeats the check in usbcore.
In itself this isn't a big deal. But people have recently found that
certain sequences of actions will cause the snd-usb-audio driver to
reuse URBs without waiting for them to complete. In the absence of
proper checking by usbcore, the URBs get added to their endpoint list
twice. This leads to list corruption and a system freeze.
The patch makes ehci-hcd assign a meaningful value to urb->hcpriv for
isochronous URBs. Improving robustness always helps.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Artem S. Tashkinov <t.artem@lycos.com>
Reported-by: Christof Meerwald <cmeerw@cmeerw.org>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1630) cleans up a few minor items resulting from the
split-up of the ehci-hcd driver:
Remove the product_desc string from the ehci_driver_overrides
structure. All drivers will use the generic "EHCI Host
Controller" string. (This was requested by Felipe Balbi.)
Allow drivers to pass a NULL pointer to ehci_init_driver()
if they don't have to override any settings.
Remove a #define symbol that is no longer used from the
ChipIdea host driver.
Rename overrides to pci_overrides in ehci-pci.c, for
consistency with ehci-platform.c.
Mark the *_overrides structures as __initdata.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1631) fixes a bug that shows up when a config change
fails for a device under an xHCI controller. The controller needs to
be told to disable the endpoints that have been enabled for the new
config. The existing code does this, but before storing the
information about which endpoints were enabled! As a result, any
second attempt to install the new config is doomed to fail because
xhci-hcd will refuse to enable an endpoint that is already enabled.
The patch optimistically initializes the new endpoints' device
structures before asking the device to switch to the new config. If
the request fails then the endpoint information is already stored, so
we can use usb_hcd_alloc_bandwidth() to disable the endpoints with no
trouble. The rest of the error path is slightly more complex now; we
have to disable the new interfaces and call put_device() rather than
simply deallocating them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Matthias Schniedermeyer <ms@citd.de>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
renesas_usbhs implements ->pullup() method, switches over
to devm_request_irq(), adds support for DMA Engine and
got a few miscelaneous cleanups.
The NCM gadget got an endianness fix and the Ethernet
gadget a frame size fix.
We're finally removing the g_file_storage gadget and
sticking to g_mass_storage and the new tcm_usb_gadget
gadgets since that was a huge duplicaton of effort anyway.
While removing g_file_storage, we also had to fix a bunch
of defconfigs which were still pointing to the old gadget.
There's a big series getting us closer to being able to
introduce our configfs interface. The series converts
functions into loadable modules which will, eventually,
be registered to the configfs interface.
Other than that there's the usual typo fixes and miscelaneous
cleanups all over the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=umtl
-----END PGP SIGNATURE-----
Merge tag 'gadget-for-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB gadget patches from Felipe:
"usb: gadget: patches for v3.8
renesas_usbhs implements ->pullup() method, switches over
to devm_request_irq(), adds support for DMA Engine and
got a few miscelaneous cleanups.
The NCM gadget got an endianness fix and the Ethernet
gadget a frame size fix.
We're finally removing the g_file_storage gadget and
sticking to g_mass_storage and the new tcm_usb_gadget
gadgets since that was a huge duplicaton of effort anyway.
While removing g_file_storage, we also had to fix a bunch
of defconfigs which were still pointing to the old gadget.
There's a big series getting us closer to being able to
introduce our configfs interface. The series converts
functions into loadable modules which will, eventually,
be registered to the configfs interface.
Other than that there's the usual typo fixes and miscelaneous
cleanups all over the place."
We can finaly drop HAVE_CLK dependency from exynos glue layer
now that clk API provides no-op stubs when it's not linked
into the kernel.
We're also switching over event buffer allocation to devm_kzalloc()
and moving the allocation out of dwc3_core_init() so that can be
re-used when implementing PM support for v3.9.
After the introduction of PLATFORM_DEVID_AUTO, we can also drop the
homebrew platform device ID handling we had on dwc3 core and let
driver core take care of that for us.
Exynos glue layer learns about DeviceTree and drops platform_data
support completely.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=wqLI
-----END PGP SIGNATURE-----
Merge tag 'dwc3-for-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB dwc3 patches from Felipe:
"usb: dwc3: patches for v3.8
We can finaly drop HAVE_CLK dependency from exynos glue layer
now that clk API provides no-op stubs when it's not linked
into the kernel.
We're also switching over event buffer allocation to devm_kzalloc()
and moving the allocation out of dwc3_core_init() so that can be
re-used when implementing PM support for v3.9.
After the introduction of PLATFORM_DEVID_AUTO, we can also drop the
homebrew platform device ID handling we had on dwc3 core and let
driver core take care of that for us.
Exynos glue layer learns about DeviceTree and drops platform_data
support completely."
We have here the usual set of cleanups for the MUSB driver; a
big set of patches converting platform_device_del() and
platform_device_put() into platform_device_unregister().
Another big set was applied converting to module_platform_driver()
macro in order to reduce some boilerplate code from all glue
layers.
Other than that, we had a series fixing one known silicon errata
where we couldn't read a few registers. In order to fix that
we're now using shadow variables for reads and only writing
to the registers which are known to break functionality when
read.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=tr2i
-----END PGP SIGNATURE-----
Merge tag 'musb-for-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB musb merge from Felipe:
"usb: musb: patches for v3.8 merge window
We have here the usual set of cleanups for the MUSB driver; a
big set of patches converting platform_device_del() and
platform_device_put() into platform_device_unregister().
Another big set was applied converting to module_platform_driver()
macro in order to reduce some boilerplate code from all glue
layers.
Other than that, we had a series fixing one known silicon errata
where we couldn't read a few registers. In order to fix that
we're now using shadow variables for reads and only writing
to the registers which are known to break functionality when
read."
Not too many patches this time. First two patches are only
cleanups where one of them switches over to module_platform_driver
macro and the second removes inclusion of <mach/iomap.h> and is
part of a bigger set of include cleanups from the Tegra folks.
The only substantial change here is the addition of a driver
for Renesas' R-Car USB Phy controller.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQnWcbAAoJEIaOsuA1yqREmSAQALGLSzrFrcmJcUBEckTlSLu3
H9Dc4GzJk1R8eyyippPgMeJKDwsXBZuZUC+KoEoeyTdm5lqBKLYwkqdHlYrlxlFX
J8FpIzXNYih4hEaOuhkCsojSsJXZODASDowqRunEcFaOOSv6J1zZQVe3mtw9H5Ap
59gXz9Fdcyc4D9JnPvkJpNxBiGBTQMNUjJ0yyUZNwHh1N+zdwQ+De3msxEaDHoJF
it9e92QdfCZrSPIXC+hjVLgPG3JeMsQsJabRq8hlRfJzdMP5rdE6WVadkaDFcaPl
pbNIKxSmz9QaD8IfVivmyRw6oG0/yiSbmKXgz+npj6bo/nzlYaTYbgWNaIeLA2US
E9QM8MSGYl1nefNjhfobVTxVUOmi5vYcBXo9OMXBS6NO3TczGGQLMQzOO6Xmnqf6
MzsvdmbMgWsz0OjT2MopxyUTVTh/ps5nUaySyrnSlXC95yUH65Ky5avBUC1jqWxj
YbZiqaLgSccKDIo4UOgQFaMR6jKxUQx+fgJy/s9uCdFh0EGAhfrVP+DpX12erHQ/
F+5uVja4H/nLeCff2ea0kIV9tyouaRe/89stWQ28RIE/yLrHN41KmrwppoJZwhxl
fzW3kWKASIVTy976Hk/N9d13TnpZIj2eJWR2LIzkt2BDb6dfN+IV0NPwreiTe92L
l7RScAepGbF5HK3aFAuu
=6i3J
-----END PGP SIGNATURE-----
Merge tag 'xceiv-for-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into USB-next
Pull USB phy patches from Felipe:
"usb: phy: patches for v3.8 merge window
Not too many patches this time. First two patches are only
cleanups where one of them switches over to module_platform_driver
macro and the second removes inclusion of <mach/iomap.h> and is
part of a bigger set of include cleanups from the Tegra folks.
The only substantial change here is the addition of a driver
for Renesas' R-Car USB Phy controller."
This reverts commit d8c3ef256f.
Above mentioned change was made along with multi usb phy change and
adding DT support for nop transceiver. But other two changes did not
make it to mainline. This in effect makes dsps musb wrapper unusable
even for single instance.
Hence revert it so that at least single instance can be supported.
Cc: stable@vger.kernel.org # v3.7
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert USB descriptor's fields to CPU byte order before using locally in USB
NCM gadget driver.
Tested on MIPS32 big-endian device.
Signed-off-by: Dmytro Milinevskyy <milinevskyy@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Checking skb->len against ETH_FRAME_LEN assumes a 1514
ethernet frame size. With an 802.1Q VLAN header, ethernet
frame length can now be 1518. Validate frame length against that.
Signed-off-by: Ian Coolidge <iancoolidge@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit removes the /sys/devices/platform/<UDC>/udc/<UDC>/is_dualspeed
file and is_dualspeeed line from /sys/devices/platform/ci13xxx_*/udc/device
file.
The is_dualspeed file is superseded by maximum_speed in the same directory
and is_dualspeed line in device file is superseded by max_speed line in
the same file.
The maximum_speed/max_speed specifies maximum speed supported by UDC.
To check if dualspeeed is supported, check if the value is >= 3.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since function-line macros are to be avoided, this commit replaces
the fsg_lun_is_open() macro with a static inline function.
While at it, this commit also adds “inline” modifier to the
fsg_lun_from_dev() function.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
storage_common.c has been used by both file_storage.c and f_mass_storage.c
which had some different requirements in a few places. To accomodate for
that, storage_common.c provided configuratian macros which were to be
defined (or not) prior to the file #inclusion. Because now
file_storage.c is no longer with us, we can remove support for those
macros and thus simplify the code slightly.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since g_file_storage has been removed, this commit removes code from
the storage_common.c file which has been used by file_storage.c only
(and not by f_mass_storage.c).
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The File-backed Storage Gadget (g_file_storage) gadget has been replaced
with Mass Storage Gadget (g_mass_storage) which uses the composite
framework. This commit removes g_file_storage (and most references to it).
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
received data will break if it was bulk pipe and large data size,
because pipe kept BUF PID even though it doesn't have enough buffer.
To avoid this issue, renesas_usbhs can use transfer counter.
Pipe PID will be NAK if it didn't have enough buffer by this patch.
renesas_usbhs has strange address mapping.
Thus, it is difficult to calculate transfer counter setting address.
This patch use fixed table for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 380f0d2 (usb: dwc3: core: switch event
buffer allocation to devm_kzalloc()) was incomplete
leaving a trailing kfree(evt) in an error exit
path.
Fix this problem by removing the trailing kfree(evt).
Cc: Julia Lawall <julia.lawall@lip6.fr>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Checking skb->len against ETH_FRAME_LEN assumes a 1514
ethernet frame size. With an 802.1Q VLAN header, ethernet
frame length can now be 1518. Validate frame length against that.
Signed-off-by: Ian Coolidge <iancoolidge@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From Michal Simek:
* 'arm-next' of git://git.xilinx.com/linux-xlnx:
zynq: move static peripheral mappings
zynq: remove use of CLKDEV_LOOKUP
zynq: use pl310 device tree bindings
zynq: use GIC device tree bindings
+ Linux 3.7-rc3
This patch is based on the discussion of a previous patch to fix an issue
where the omap2430 musb driver is not working for N9/N950.
Moving all the interrupt handling to the devices. Avoids inclusion of generic
interrupt and breakage due to sometimes misleading CONFIG options. This makes
sure usb always works if on of the subdrivers is chosen. Tested on Nokia N9/N950.
Partially clean up CONFIG_SOC_OMAP3430 which is not necessary in the cases
where I removed it. Also helps with the removal work of those options that
Tony Lindgren predicted would happen at some point.
Signed-off-by: Philippe De Swert <philippe.deswert@jollamobile.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now that DaVinci glue layer can be modular, we must export cppi_interrupt()
that it may call...
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
renesas_usbhs attaches pipe to endpoint when urb was queued, and it will be
detached when transfer was done. Multi device controlling was enabled by this
behavior.
Now renesas_usbhs driver tried to wait until detaching if urb was queued to
endpoint which already has been attached to pipe, and it created strange driver
behavior.
But it can re-use this attached pipe if multi urb was queued. This patch
implements it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Because usbhsh_hub_status_data() will be called many times,
there are too many obstructive/useless debug informations if driver has #define DEBUG.
Thus, other important dev_dbg() information will hide.
This patch removed obstructive/useless dev_dbg().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
