commit f5c8cf2a49 upstream.
Commit 46573fd636 ("cpufreq: intel_pstate: hybrid: Rework HWP
calibration") attempted to use the information from CPPC (the nominal
performance in particular) to obtain the scaling factor allowing the
frequency to be computed if the HWP performance level of the given CPU
is known or vice versa.
However, it turns out that on some platforms this doesn't work, because
the CPPC information on them does not align with the contents of the
MSR_HWP_CAPABILITIES registers.
This basically means that the only way to make intel_pstate work on all
of the hybrid platforms to date is to use the observation that on all
of them the scaling factor between the HWP performance levels and
frequency for P-cores is 78741 (approximately 100000/1.27). For
E-cores it is 100000, which is the same as for all of the non-hybrid
"core" platforms and does not require any changes.
Accordingly, make intel_pstate use 78741 as the scaling factor between
HWP performance levels and frequency for P-cores on all hybrid platforms
and drop the dependency of the HWP calibration code on CPPC.
Fixes: 46573fd636 ("cpufreq: intel_pstate: hybrid: Rework HWP calibration")
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 5.15+ <stable@vger.kernel.org> # 5.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dbab94d45 upstream.
Some of the MSR accesses in intel_pstate are carried out on the CPU
that is running the code, but the values coming from them are used
for the performance scaling of the other CPUs.
This is problematic, for example, on hybrid platforms where
MSR_TURBO_RATIO_LIMIT for P-cores and E-cores is different, so the
values read from it on a P-core are generally not applicable to E-cores
and the other way around.
For this reason, make the driver access all MSRs on the target CPU on
platforms using the "core" pstate_funcs callbacks which is the case for
all of the hybrid platforms released to date. For this purpose, pass
a CPU argument to the ->get_max(), ->get_max_physical(), ->get_min()
and ->get_turbo() pstate_funcs callbacks and from there pass it to
rdmsrl_on_cpu() or rdmsrl_safe_on_cpu() to access the MSR on the target
CPU.
Fixes: 46573fd636 ("cpufreq: intel_pstate: hybrid: Rework HWP calibration")
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 5.15+ <stable@vger.kernel.org> # 5.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f42cf5440 upstream.
If for some reason the speedbin length is incorrect, then there is a
memory leak in the error path because we never free the speedbin buffer.
This commit fixes the error path to always free the speedbin buffer.
Cc: v5.7+ <stable@vger.kernel.org> # v5.7+
Fixes: a8811ec764 ("cpufreq: qcom: Add support for krait based socs")
Signed-off-by: Fabien Parent <fabien.parent@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1dcaf30725 upstream.
When the Tegra194 CPUFREQ driver is built as a module it is not
automatically loaded as expected on Tegra194 devices. Populate the
MODULE_DEVICE_TABLE to fix this.
Cc: v5.9+ <stable@vger.kernel.org> # v5.9+
Fixes: df320f8935 ("cpufreq: Add Tegra194 cpufreq driver")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01039fb8e9 upstream.
This commit fixes a kernel oops because of a write in some read-only memory:
[ 9.068287] Unable to handle kernel write to read-only memory at virtual address ffff800009240ad8
..snip..
[ 9.138790] Internal error: Oops: 9600004f [#1] PREEMPT SMP
..snip..
[ 9.269161] Call trace:
[ 9.276271] __memcpy+0x5c/0x230
[ 9.278531] snprintf+0x58/0x80
[ 9.282002] qcom_cpufreq_msm8939_name_version+0xb4/0x190
[ 9.284869] qcom_cpufreq_probe+0xc8/0x39c
..snip..
The following line defines a pointer that point to a char buffer stored
in read-only memory:
char *pvs_name = "speedXX-pvsXX-vXX";
This pointer is meant to hold a template "speedXX-pvsXX-vXX" where the
XX values get overridden by the qcom_cpufreq_krait_name_version function. Since
the template is actually stored in read-only memory, when the function
executes the following call we get an oops:
snprintf(*pvs_name, sizeof("speedXX-pvsXX-vXX"), "speed%d-pvs%d-v%d",
speed, pvs, pvs_ver);
To fix this issue, we instead store the template name onto the stack by
using the following syntax:
char pvs_name_buffer[] = "speedXX-pvsXX-vXX";
Because the `pvs_name` needs to be able to be assigned to NULL, the
template buffer is stored in the pvs_name_buffer and not under the
pvs_name variable.
Cc: v5.7+ <stable@vger.kernel.org> # v5.7+
Fixes: a8811ec764 ("cpufreq: qcom: Add support for krait based socs")
Signed-off-by: Fabien Parent <fabien.parent@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 71bb5c82aa ]
Users may disable HWP in firmware, in which case intel_pstate wouldn't load
unless the CPU model is explicitly supported.
Add TIGERLAKE to the list of CPUs that can register intel_pstate while not
advertising the HWP capability. Without this change, an TIGERLAKE in no-HWP
mode could only use the acpi_cpufreq frequency scaling driver.
See also commits:
d8de7a44e1: cpufreq: intel_pstate: Add Skylake servers support
fbdc21e9b0: cpufreq: intel_pstate: Add Icelake servers support in no-HWP mode
706c532885: cpufreq: intel_pstate: Add Cometlake support in no-HWP mode
Reported by: M. Cargi Ari <cagriari@pm.me>
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b185c5053c ]
Fix the wrong lowest perf value reading which is used for new
des_perf calculation by governor requested, the incorrect min_perf will
get incorrect des_perf to be set , that will cause the system frequency
changing unexpectedly.
Reviewed-by: Huang Rui <ray.huang@amd.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Perry Yuan <Perry.Yuan@amd.com>
Signed-off-by: Su Jinzhou <jinzhou.su@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bedadcfb01 ]
To avoid some new AMD processors use wrong highest perf when amd pstate
driver loaded, this fix will query the highest perf from MSR register
MSR_AMD_CPPC_CAP1 and cppc_acpi interface firstly, then compare with the
highest perf value got by calling amd_get_highest_perf() function.
The lower value will be the correct highest perf we need to use.
Otherwise the CPU max MHz will be incorrect if the
amd_get_highest_perf() did not cover the new process family and model ID.
Like this lscpu info, the max frequency is incorrect.
Vendor ID: AuthenticAMD
Socket(s): 1
Stepping: 2
CPU max MHz: 5410.0000
CPU min MHz: 400.0000
BogoMIPS: 5600.54
Fixes: 3743d55b28 (x86, sched: Fix the AMD CPPC maximum performance value on certain AMD Ryzen generations)
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Perry Yuan <Perry.Yuan@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 91dc90fdb8 upstream.
Commit 6240aaad75 was supposed to drop the reference count to the OPP,
instead it avoided more stuff if the OPP isn't found. This isn't
entirely correct. We already have a frequency value available, we just
couldn't align it with an OPP in case of IS_ERR(opp).
Lets continue with updating thermal pressure, etc, even if we aren't
able to find an OPP here.
This fixes warning generated by the 'smatch' tool.
Fixes: 6240aaad75 ("cpufreq: qcom-hw: fix the opp entries refcounting")
Cc: v5.18+ <stable@vger.kernel.org> # v5.18+
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to check if the cpufreq driver implements callback
cpufreq_driver::target_index. The logic in the __resolve_freq uses
the frequency table available in the policy. It doesn't matter if the
driver provides 'target_index' or 'target' callback. It just has to
populate the 'policy->freq_table'.
Thus, check only frequency table during the frequency resolving call.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Fix return error code in mtk_cpu_dvfs_info_init (Yang Yingliang).
- Minor cleanups and support for new boards for Qcom cpufreq drivers
(Bryan O'Donoghue, Konrad Dybcio, Pierre Gondois, and Yicong Yang).
- Fix sparse warnings for Tegra cpufreq driver (Viresh Kumar).
- Make dev_pm_opp_set_regulators() accept NULL terminated list (Viresh
Kumar).
- Add dev_pm_opp_set_config() and friends and migrate other users and
helpers to using them (Viresh Kumar).
- Add support for multiple clocks for a device (Viresh Kumar and
Krzysztof Kozlowski).
- Configure resources before adding OPP table for Venus (Stanimir
Varbanov).
- Keep reference count up for opp->np and opp_table->np while they are
still in use (Liang He).
- Minor OPP cleanups (Viresh Kumar and Yang Li).
- Add a trace event for cpuidle to track missed (too deep or too
shallow) wakeups (Kajetan Puchalski).
-----BEGIN PGP SIGNATURE-----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=LBb0
-----END PGP SIGNATURE-----
Merge tag 'pm-5.20-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These are ARM cpufreq updates and operating performance points (OPP)
updates plus one cpuidle update adding a new trace point.
Specifics:
- Fix return error code in mtk_cpu_dvfs_info_init (Yang Yingliang).
- Minor cleanups and support for new boards for Qcom cpufreq drivers
(Bryan O'Donoghue, Konrad Dybcio, Pierre Gondois, and Yicong Yang).
- Fix sparse warnings for Tegra cpufreq driver (Viresh Kumar).
- Make dev_pm_opp_set_regulators() accept NULL terminated list
(Viresh Kumar).
- Add dev_pm_opp_set_config() and friends and migrate other users and
helpers to using them (Viresh Kumar).
- Add support for multiple clocks for a device (Viresh Kumar and
Krzysztof Kozlowski).
- Configure resources before adding OPP table for Venus (Stanimir
Varbanov).
- Keep reference count up for opp->np and opp_table->np while they
are still in use (Liang He).
- Minor OPP cleanups (Viresh Kumar and Yang Li).
- Add a trace event for cpuidle to track missed (too deep or too
shallow) wakeups (Kajetan Puchalski)"
* tag 'pm-5.20-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (55 commits)
cpuidle: Add cpu_idle_miss trace event
venus: pm_helpers: Fix warning in OPP during probe
OPP: Don't drop opp->np reference while it is still in use
OPP: Don't drop opp_table->np reference while it is still in use
cpufreq: tegra194: Staticize struct tegra_cpufreq_soc instances
dt-bindings: cpufreq: cpufreq-qcom-hw: Add SM6375 compatible
dt-bindings: opp: Add msm8939 to the compatible list
dt-bindings: opp: Add missing compat devices
dt-bindings: opp: opp-v2-kryo-cpu: Fix example binding checks
cpufreq: Change order of online() CB and policy->cpus modification
cpufreq: qcom-hw: Remove deprecated irq_set_affinity_hint() call
cpufreq: qcom-hw: Disable LMH irq when disabling policy
cpufreq: qcom-hw: Reset cancel_throttle when policy is re-enabled
cpufreq: qcom-cpufreq-hw: use HZ_PER_KHZ macro in units.h
cpufreq: mediatek: fix error return code in mtk_cpu_dvfs_info_init()
OPP: Remove dev{m}_pm_opp_of_add_table_noclk()
PM / devfreq: tegra30: Register config_clks helper
OPP: Allow config_clks helper for single clk case
OPP: Provide a simple implementation to configure multiple clocks
OPP: Assert clk_count == 1 for single clk helpers
...
Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text. Also included in here are a few other minor updates,
2 USB files, and one Documentation file update to get the SPDX lines
correct.
All of these have been in the linux-next tree for a very long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYupz3g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynPUgCgslaf2ssCgW5IeuXbhla+ZBRAzisAnjVgOvLN
4AKdqbiBNlFbCroQwmeQ
=v1sg
-----END PGP SIGNATURE-----
Merge tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
- Make dev_pm_opp_set_regulators() accept NULL terminated list (Viresh
Kumar).
- Add dev_pm_opp_set_config() and friends and migrate other
users/helpers to using them (Viresh Kumar).
- Add support for multiple clocks for a device (Viresh Kumar and
Krzysztof Kozlowski).
- Configure resources before adding OPP table for Venus (Stanimir
Varbanov).
- Keep reference count up for opp->np and opp_table->np while they are
still in use (Liang He).
- Minor cleanups (Viresh Kumar and Yang Li).
-----BEGIN PGP SIGNATURE-----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=NHBQ
-----END PGP SIGNATURE-----
Merge tag 'opp-updates-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Pull operating performance points (OPP) updates for 5.20-rc1 from Viresh
Kumar:
"- Make dev_pm_opp_set_regulators() accept NULL terminated list (Viresh
Kumar).
- Add dev_pm_opp_set_config() and friends and migrate other
users/helpers to using them (Viresh Kumar).
- Add support for multiple clocks for a device (Viresh Kumar and
Krzysztof Kozlowski).
- Configure resources before adding OPP table for Venus (Stanimir
Varbanov).
- Keep reference count up for opp->np and opp_table->np while they are
still in use (Liang He).
- Minor cleanups (Viresh Kumar and Yang Li)."
* tag 'opp-updates-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm: (43 commits)
venus: pm_helpers: Fix warning in OPP during probe
OPP: Don't drop opp->np reference while it is still in use
OPP: Don't drop opp_table->np reference while it is still in use
OPP: Remove dev{m}_pm_opp_of_add_table_noclk()
PM / devfreq: tegra30: Register config_clks helper
OPP: Allow config_clks helper for single clk case
OPP: Provide a simple implementation to configure multiple clocks
OPP: Assert clk_count == 1 for single clk helpers
OPP: Add key specific assert() method to key finding helpers
OPP: Compare bandwidths for all paths in _opp_compare_key()
OPP: Allow multiple clocks for a device
dt-bindings: opp: accept array of frequencies
OPP: Make dev_pm_opp_set_opp() independent of frequency
OPP: Reuse _opp_compare_key() in _opp_add_static_v2()
OPP: Remove rate_not_available parameter to _opp_add()
OPP: Use consistent names for OPP table instances
OPP: Use generic key finding helpers for bandwidth key
OPP: Use generic key finding helpers for level key
OPP: Add generic key finding helpers and use them for freq APIs
OPP: Remove dev_pm_opp_find_freq_ceil_by_volt()
...
- Fix return error code in mtk_cpu_dvfs_info_init (Yang Yingliang).
- Minor cleanups and support for new boards for Qcom cpufreq drivers
(Bryan O'Donoghue, Konrad Dybcio, Pierre Gondois, and Yicong Yang).
- Fix sparse warnings for Tegra driver (Viresh Kumar).
-----BEGIN PGP SIGNATURE-----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=fX64
-----END PGP SIGNATURE-----
Merge tag 'cpufreq-arm-updates-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Pull cpufreq/ARM updates for 5.20-rc1 from Viresh Kumar:
"- Fix return error code in mtk_cpu_dvfs_info_init (Yang Yingliang).
- Minor cleanups and support for new boards for Qcom cpufreq drivers
(Bryan O'Donoghue, Konrad Dybcio, Pierre Gondois, and Yicong Yang).
- Fix sparse warnings for Tegra driver (Viresh Kumar)."
* tag 'cpufreq-arm-updates-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: tegra194: Staticize struct tegra_cpufreq_soc instances
dt-bindings: cpufreq: cpufreq-qcom-hw: Add SM6375 compatible
dt-bindings: opp: Add msm8939 to the compatible list
dt-bindings: opp: Add missing compat devices
dt-bindings: opp: opp-v2-kryo-cpu: Fix example binding checks
cpufreq: Change order of online() CB and policy->cpus modification
cpufreq: qcom-hw: Remove deprecated irq_set_affinity_hint() call
cpufreq: qcom-hw: Disable LMH irq when disabling policy
cpufreq: qcom-hw: Reset cancel_throttle when policy is re-enabled
cpufreq: qcom-cpufreq-hw: use HZ_PER_KHZ macro in units.h
cpufreq: mediatek: fix error return code in mtk_cpu_dvfs_info_init()
Merge core device power management changes for v5.20-rc1:
- Extend support for wakeirq to callback wrappers used during system
suspend and resume (Ulf Hansson).
- Defer waiting for device probe before loading a hibernation image
till the first actual device access to avoid possible deadlocks
reported by syzbot (Tetsuo Handa).
- Unify device_init_wakeup() for PM_SLEEP and !PM_SLEEP (Bjorn
Helgaas).
- Add Raptor Lake-P to the list of processors supported by the Intel
RAPL driver (George D Sworo).
- Add Alder Lake-N and Raptor Lake-P to the list of processors for
which Power Limit4 is supported in the Intel RAPL driver (Sumeet
Pawnikar).
- Make pm_genpd_remove() check genpd_debugfs_dir against NULL before
attempting to remove it (Hsin-Yi Wang).
- Change the Energy Model code to represent power in micro-Watts and
adjust its users accordingly (Lukasz Luba).
* pm-core:
PM: runtime: Extend support for wakeirq for force_suspend|resume
* pm-sleep:
PM: hibernate: defer device probing when resuming from hibernation
PM: wakeup: Unify device_init_wakeup() for PM_SLEEP and !PM_SLEEP
* powercap:
powercap: RAPL: Add Power Limit4 support for Alder Lake-N and Raptor Lake-P
powercap: intel_rapl: Add support for RAPTORLAKE_P
* pm-domains:
PM: domains: Ensure genpd_debugfs_dir exists before remove
* pm-em:
cpufreq: scmi: Support the power scale in micro-Watts in SCMI v3.1
firmware: arm_scmi: Get detailed power scale from perf
Documentation: EM: Switch to micro-Watts scale
PM: EM: convert power field to micro-Watts precision and align drivers
A cpumask structure on the stack can cause a warning with
CONFIG_NR_CPUS=8192 (e.g. Ubuntu 22.04 uses this):
drivers/cpufreq/cpufreq_ondemand.c: In function 'od_set_powersave_bias':
drivers/cpufreq/cpufreq_ondemand.c:449:1: warning: the frame size of
1032 bytes is larger than 1024 bytes [-Wframe-larger-than=]
449 | }
| ^
CONFIG_CPUMASK_OFFSTACK=y is enabled by default for most distros, and
hence we can work around the warning by using cpumask_var_t.
Signed-off-by: Zhao Liu <zhao1.liu@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use the possessive "its" instead of the contraction "it's"
where appropriate.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
From a state where all policy->related_cpus are offline, putting one
of the policy's CPU back online re-activates the policy by:
1. Calling cpufreq_driver->online()
2. Setting the CPU in policy->cpus
qcom_cpufreq_hw_cpu_online() makes use of policy->cpus. Thus 1. and 2.
should be inverted to avoid having a policy->cpus empty. The
qcom-cpufreq-hw is the only driver affected by this.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
With the new design in place, the show() and store() callbacks check if
the policy is active or not before proceeding any further to avoid
potential races. And in order to guarantee that cpufreq_policy_free()
must be called after clearing the policy->cpus mask, i.e. by marking the
policy inactive.
In order to avoid introducing a bug around this later, print a warning
message if we end up freeing an active policy.
Also update cpufreq_online() a bit to make sure we clear the cpus mask
for each error case before calling cpufreq_policy_free().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The SCMI v3.1 adds support for power values in micro-Watts. They are not
always in milli-Watts anymore (ignoring the bogo-Watts). Thus, the power
must be converted conditionally before sending to Energy Model. Add the
logic which handles the needed checks and conversions.
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The milli-Watts precision causes rounding errors while calculating
efficiency cost for each OPP. This is especially visible in the 'simple'
Energy Model (EM), where the power for each OPP is provided from OPP
framework. This can cause some OPPs to be marked inefficient, while
using micro-Watts precision that might not happen.
Update all EM users which access 'power' field and assume the value is
in milli-Watts.
Solve also an issue with potential overflow in calculation of energy
estimation on 32bit machine. It's needed now since the power value
(thus the 'cost' as well) are higher.
Example calculation which shows the rounding error and impact:
power = 'dyn-power-coeff' * volt_mV * volt_mV * freq_MHz
power_a_uW = (100 * 600mW * 600mW * 500MHz) / 10^6 = 18000
power_a_mW = (100 * 600mW * 600mW * 500MHz) / 10^9 = 18
power_b_uW = (100 * 605mW * 605mW * 600MHz) / 10^6 = 21961
power_b_mW = (100 * 605mW * 605mW * 600MHz) / 10^9 = 21
max_freq = 2000MHz
cost_a_mW = 18 * 2000MHz/500MHz = 72
cost_a_uW = 18000 * 2000MHz/500MHz = 72000
cost_b_mW = 21 * 2000MHz/600MHz = 70 // <- artificially better
cost_b_uW = 21961 * 2000MHz/600MHz = 73203
The 'cost_b_mW' (which is based on old milli-Watts) is misleadingly
better that the 'cost_b_uW' (this patch uses micro-Watts) and such
would have impact on the 'inefficient OPPs' information in the Cpufreq
framework. This patch set removes the rounding issue.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
commit 65c7cdedeb ("genirq: Provide new interfaces for affinity hints")
deprecates irq_set_affinity_hint(). Use the new
irq_set_affinity_and_hint() instead.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
If LMH (Limits Management Hardware) is available, when a policy is
disabled by unplugging the last online CPU of policy->cpus, the LMH
irq is left enabled.
When the policy is re-enabled with any of the CPU in policy->cpus
being plugged in, qcom_cpufreq_ready() re-enables the irq. This
triggers the following warning:
[ 379.160106] Unbalanced enable for IRQ 154
[ 379.160120] WARNING: CPU: 7 PID: 48 at kernel/irq/manage.c:774 __enable_irq+0x84/0xc0
Thus disable the irq.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
If LMH (Limits Management Hardware) is available, when a policy is
disabled by unplugging the last online CPU of policy->cpus,
qcom_cpufreq_hw_cpu_offline() sets cancel_throttle=true.
cancel_throttle is not reset when the policy is re-enabled with any
of the CPU in policy->cpus being plugged in. So reset it.
This patch also adds an early exit check.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
HZ macros has been centralized in units.h since [1]. Use it to avoid
duplicated definition.
[1] commit e2c77032fc ("units: add the HZ macros")
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
If regulator_get_voltage() fails, it should return the error code in
mtk_cpu_dvfs_info_init().
Fixes: 0daa47325b ("cpufreq: mediatek: Link CCI device to CPU")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
If the regulator_get_optional() call for the SRAM regulator returns
a probe deferral, we must bail out and retry probing later: failing
to do this will produce unstabilities on platforms requiring the
handling for this regulator.
Fixes: ffa7bdf7f3 ("cpufreq: mediatek: Make sram regulator optional")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Now that we have a central API to handle all OPP table configurations,
migrate the set-prop-name family of helpers to use the new
infrastructure.
The return type and parameter to the APIs change a bit due to this,
update the current users as well in the same commit in order to avoid
breaking builds.
Acked-by: Samuel Holland <samuel@sholland.org> # sun50i
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Now that we have a central API to handle all OPP table configurations,
migrate the set-supported-hw family of helpers to use the new
infrastructure.
The return type and parameter to the APIs change a bit due to this,
update the current users as well in the same commit in order to avoid
breaking builds.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Now that we have a central API to handle all OPP table configurations,
migrate the set-regulators family of helpers to use the new
infrastructure.
The return type and parameter to the APIs change a bit due to this,
update the current users as well in the same commit in order to avoid
breaking builds.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The OPP core now provides a unified API for setting all configuration
types, i.e. dev_pm_opp_set_config().
Lets start using it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The OPP core now provides a unified API for setting all configuration
types, i.e. dev_pm_opp_set_config().
Lets start using it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The OPP core now provides a unified API for setting all configuration
types, i.e. dev_pm_opp_set_config().
Lets start using it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Make dev_pm_opp_set_regulators() accept a NULL terminated list of names
instead of making the callers keep the two parameters in sync, which
creates an opportunity for bugs to get in.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Steven Price <steven.price@arm.com> # panfrost
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Recent Zhaoxin/Centaur CPUs support X86_FEATURE_IDA and the turbo boost
can be dynamically enabled or disabled through MSR 0x1a0[38] in the same
way as Intel. So add turbo boost control support for these CPUs too.
Signed-off-by: Tony W Wang-oc <TonyWWang-oc@zhaoxin.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This SoC shall use the mediatek-cpufreq driver, or the system will
crash upon any clock scaling request: add it to the cpufreq-dt-platdev
blocklist.
Fixes: 39b360102f ("cpufreq: mediatek: Add support for MT8186")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
In pmac_cpufreq_init_MacRISC3(), we need to add corresponding
of_node_put() for the three node pointers whose refcount have
been incremented by of_find_node_by_name().
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Offlining cpu6 and cpu7 and then onlining cpu6 hangs on
sc7180-trogdor-lazor because the throttle interrupt doesn't exist.
Similarly, things go sideways when suspend/resume runs. That's because
the qcom_cpufreq_hw_cpu_online() and qcom_cpufreq_hw_lmh_exit()
functions are calling genirq APIs with an interrupt value of '-6', i.e.
-ENXIO, and that isn't good.
Check the value of the throttle interrupt like we already do in other
functions in this file and bail out early from lmh code to fix the hang.
Reported-by: Rob Clark <robdclark@chromium.org>
Cc: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: a1eb080a04 ("cpufreq: qcom-hw: provide online/offline operations")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
In qoriq_cpufreq_probe(), of_find_matching_node() will return a
node pointer with refcount incremented. We should use of_node_put()
when it is not used anymore.
Fixes: 157f527639 ("cpufreq: qoriq: convert to a platform driver")
[ Viresh: Fixed Author's name in commit log ]
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
When system resumes from S3, the CPPC enable register will be
cleared and reset to 0.
So enable the CPPC interface by writing 1 to this register on
system resume and disable it during system suspend.
Signed-off-by: Jinzhou Su <Jinzhou.Su@amd.com>
Signed-off-by: Jinzhou Su <Jinzhou.Su@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
[ rjw: Subject and changelog edits ]
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This change was introduced long back by commit 4f750c9308 ("cpufreq:
Synchronize the cpufreq store_*() routines with CPU hotplug").
Since then, both cpufreq and hotplug core have been reworked and have
much better locking in place. The race mentioned in commit 4f750c9308
isn't possible anymore.
Drop the unnecessary locking.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Instead of specially adding a space for each CPU, except the first one,
lets add space for each of them and remove it at the end.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license version 2 as
published by the free software foundation this program is distributed
as is without any warranty of any kind whether express or implied
without even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the normalized pattern:
this file is licensed under the terms of the gnu general public
license version 2 this program is licensed as is without any warranty
of any kind whether express or implied
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
