Suspending the bus and host controller while a port is in a over-current
condition may halt the host.
Also keep the roothub running if over-current is active.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200421140822.28233-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Depending on the current link state the steps to resume the link to U0
varies. The normal case when a port is suspended (U3) we set the link
to U0 and wait for a port event when U3exit completed and port moved to
U0.
If the port is in U1/U2, then no event is issued, just set link to U0
If port is in Resume or Recovery state then the device has already
initiated resume, and this host initiated resume is racing against it.
Port event handler for device initiated resume will set link to U0,
just wait for the port to reach U0 before returning.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like U3 case, xHCI spec doesn't specify the upper bound of U0 transition
time. The 20ms is not enough for some devices.
Intead of polling PLS or PLC, we can facilitate the port change event to
know that the link transits to U0 is completed.
While at it, also separate U0 and U3 case to make the code cleaner.
[variable rename to u3exit, and skip completion for usb2 ports -Mathias ]
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI spec doesn't specify the upper bound of U3 transition time. For
some devices 20ms is not enough, so we need to make sure the link state
is in U3 before further actions.
I've tried to use U3 Entry Capability by setting U3 Entry Enable in
config register, however the port change event for U3 transition
interrupts the system suspend process.
For now let's use the less ideal method by polling PLS.
[use usleep_range(), and shorten the delay time while polling -Mathias]
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sparse reports a warning at xhci_enter_test_mode()
warning: context imbalance in xhci_enter_test_mode - unexpected unlock
The root cause is the missing annotation at xhci_enter_test_mode()
Add the missing __must_hold(&xhci->lock) annotattion
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Link: https://lore.kernel.org/r/20200214204741.94112-24-jbi.octave@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sparse reports a warning at xhci_set_port_power()
warning: context imbalance in xhci_set_port_power - unexpected unlock
The root cause is the missing annotation at xhci_set_port_power()
Add the missing __must_hold(&xhci->lock) annotattion
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Link: https://lore.kernel.org/r/20200214204741.94112-23-jbi.octave@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver assumed that xHC controllers have at most one custom
supported speed table (PSI) for all usb 3.x ports.
Memory was allocated for one PSI table under the xhci hub structure.
Turns out this is not the case, some controllers have a separate
"supported protocol capability" entry with a PSI table for each port.
This means each usb3 roothub port can in theory support different custom
speeds.
To solve this, cache all supported protocol capabilities with their PSI
tables in an array, and add pointers to the xhci port structure so that
every port points to its capability entry in the array.
When creating the SuperSpeedPlus USB Device Capability BOS descriptor
for the xhci USB 3.1 roothub we for now will use only data from the
first USB 3.1 capable protocol capability entry in the array.
This could be improved later, this patch focuses resolving
the memory leak.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reported-by: Sajja Venkateswara Rao <VenkateswaraRao.Sajja@amd.com>
Fixes: 47189098f8 ("xhci: parse xhci protocol speed ID list for usb 3.1 usage")
Cc: stable <stable@vger.kernel.org> # v4.4+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200211150158.14475-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit fc57313d10.
Marek reports that it breaks things:
This patch landed in today's linux-next (20200211) and causes
NULL pointer dereference during second suspend/resume cycle on
Samsung Exynos5422-based (arm 32bit) Odroid XU3lite board:
A more complete fix will be added soon.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: fc57313d10 ("xhci: Fix memory leak when caching protocol extended capability PSI tables")
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
Cc: Sajja Venkateswara Rao <VenkateswaraRao.Sajja@amd.com>
Cc: stable <stable@vger.kernel.org> # v4.4+
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver assumed that xHC controllers have at most one custom
supported speed table (PSI) for all usb 3.x ports.
Memory was allocated for one PSI table under the xhci hub structure.
Turns out this is not the case, some controllers have a separate
"supported protocol capability" entry with a PSI table for each port.
This means each usb3 roothub port can in theory support different custom
speeds.
To solve this, cache all supported protocol capabilities with their PSI
tables in an array, and add pointers to the xhci port structure so that
every port points to its capability entry in the array.
When creating the SuperSpeedPlus USB Device Capability BOS descriptor
for the xhci USB 3.1 roothub we for now will use only data from the
first USB 3.1 capable protocol capability entry in the array.
This could be improved later, this patch focuses resolving
the memory leak.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reported-by: Sajja Venkateswara Rao <VenkateswaraRao.Sajja@amd.com>
Fixes: 47189098f8 ("xhci: parse xhci protocol speed ID list for usb 3.1 usage")
Cc: stable <stable@vger.kernel.org> # v4.4+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200210134553.9144-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
spin_unlock_irqrestore() might be called with stale flags after
reading port status, possibly restoring interrupts to a incorrect
state.
If a usb2 port just finished resuming while the port status is read
the spin lock will be temporary released and re-acquired in a separate
function. The flags parameter is passed as value instead of a pointer,
not updating flags properly before the final spin_unlock_irqrestore()
is called.
Cc: <stable@vger.kernel.org> # v3.12+
Fixes: 8b3d45705e ("usb: Fix xHCI host issues on remote wakeup.")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A race in xhci USB3 remote wake handling may force device back to suspend
after it initiated resume siganaling, causing a missed resume event or warm
reset of device.
When a USB3 link completes resume signaling and goes to enabled (UO)
state a interrupt is issued and the interrupt handler will clear the
bus_state->port_remote_wakeup resume flag, allowing bus suspend.
If the USB3 roothub thread just finished reading port status before
the interrupt, finding ports still in suspended (U3) state, but hasn't
yet started suspending the hub, then the xhci interrupt handler will clear
the flag that prevented roothub suspend and allow bus to suspend, forcing
all port links back to suspended (U3) state.
Example case:
usb_runtime_suspend() # because all ports still show suspended U3
usb_suspend_both()
hub_suspend(); # successful as hub->wakeup_bits not set yet
==> INTERRUPT
xhci_irq()
handle_port_status()
clear bus_state->port_remote_wakeup
usb_wakeup_notification()
sets hub->wakeup_bits;
kick_hub_wq()
<== END INTERRUPT
hcd_bus_suspend()
xhci_bus_suspend() # success as port_remote_wakeup bits cleared
Fix this by increasing roothub usage count during port resume to prevent
roothub autosuspend, and by making sure bus_state->port_remote_wakeup
flag is only cleared after resume completion is visible, i.e.
after xhci roothub returned U0 or other non-U3 link state link on a
get port status request.
Issue rootcaused by Chiasheng Lee
Cc: <stable@vger.kernel.org>
Cc: Lee, Hou-hsun <hou-hsun.lee@intel.com>
Reported-by: Lee, Chiasheng <chiasheng.lee@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't do extra cpu_to_le32 conversion for
put_unaligned_le32 because it is already implemented
in this function.
Fixes sparse error:
xhci-hub.c:1152:44: warning: incorrect type in argument 1 (different base types)
xhci-hub.c:1152:44: expected unsigned int [usertype] val
xhci-hub.c:1152:44: got restricted __le32 [usertype]
Fixes: 395f540 "xhci: support new USB 3.1 hub request to get extended port status"
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/1562501839-26522-1-git-send-email-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve port related dynamic debugging by printing out the bus number,
port number and port status register content each time there is a port
related debug messages.
Use the same port numbering method as usbcore to simplify debugging.
i.e. starting with port number 1.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect
change or polling state is detected") was intended to prevent ports that
were still link training from being forced to U3 suspend state mid
enumeration.
This solved enumeration issues for devices with slow link training.
Turns out some devices are stuck in the link training/polling state,
and thus that patch will prevent suspend completely for these devices.
This is seen with USB3 card readers in some MacBooks.
Instead of preventing suspend, give some time to complete the link
training. On successful training the port will end up as connected
and enabled.
If port instead is stuck in link training the bus suspend will continue
suspending after 360ms (10 * 36ms) timeout (tPollingLFPSTimeout).
Original patch was sent to stable, this one should go there as well
Fixes: 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code to prevent a bus suspend if a USB3 port was still in link training
also reacted to USB2 port polling state.
This caused bus suspend to busyloop in some cases.
USB2 polling state is different from USB3, and should not prevent bus
suspend.
Limit the USB3 link training state check to USB3 root hub ports only.
The origial commit went to stable so this need to be applied there as well
Fixes: 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactoring, no functional changes.
But worth mentioning that checking for port link resume state is now behind
a additional port power check.
This is fine as ports can't be in resume state if port power bit is not
set.
xhci spec section 4.19.1.1.6 figure 34 shows that port power bit must be
set for all 'Enable' substates, including U0,U1,U2,U3 (suspended), Resume,
and RExit states.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move U0 link state handing to USB3 and USB2 specific functions
Note that
bus_state->resuming_ports:
bus_state->resume_done[]:
are only used for USB2, and don't need to cleared for USB3 ports
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Group the code where the wPortstatus and wPortChange bits
are set into one place.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mostly refactoring, with the exception that USB_PORT_STAT_L1 link state
is reported if xhci port link is in U2 AND port is powered.
Previously we did not check if the port was powered, but according to
xhci spec 4.19.1.1.6 All the 'Enabled' states, including
USB_PORT_STAT_L1 (U2), U1, U0 and U3 must have Port power bit set.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the bus_state structure under struct usb_hub.
We need a bus_state strucure for each roothub to keep track of suspend
related info for each port.
Instead of keeping an array of two bus_state structures right under
struct xhci, it makes more sense move them to the xhci_hub structure.
No functional changes.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB3 roothub might autosuspend before a plugged USB3 device is detected,
causing USB3 device enumeration failure.
USB3 devices don't show up as connected and enabled until USB3 link trainig
completes. On a fast booting platform with a slow USB3 link training the
link might reach the connected enabled state just as the bus is suspending.
If this device is discovered first time by the xhci_bus_suspend() routine
it will be put to U3 suspended state like the other ports which failed to
suspend earlier.
The hub thread will notice the connect change and resume the bus,
moving the port back to U0
This U0 -> U3 -> U0 transition right after being connected seems to be
too much for some devices, causing them to first go to SS.Inactive state,
and finally end up stuck in a polling state with reset asserted
Fix this by failing the bus suspend if a port has a connect change or is
in a polling state in xhci_bus_suspend().
Don't do any port changes until all ports are checked, buffer all port
changes and only write them in the end if suspend can proceed
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This definition is used by msecs_to_jiffies in milliseconds.
According to the comments, max rexit timeout should be 20ms.
Align with the comments to properly calculate the delay.
Verified on Sunrise Point-LP and Cannon Lake.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek USB3.0 Card Reader [0bda:0328] reports wrong port status on
Cannon lake PCH USB3.1 xHCI [8086:a36d] after resume from S3,
after clear port reset it works fine.
Since this device is registered on USB3 roothub at boot,
when port status reports not superspeed, xhci_get_port_status will call
an uninitialized completion in bus_state[0].
Kernel will hang because of NULL pointer.
Restrict the USB2 resume status check in USB2 roothub to fix hang issue.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When USB bus host controller root hub resumes from autosuspend,
it immediately tries to enter auto-suspend, but there can be a
scenario when root hub is resuming its usb2 ports, in that particular
case USB host controller auto suspend fails since it is busy
to resuming its usb2 ports.
This makes multiple failed cycles of auto-suspend until all usb2
ports of host controller root hub do not resume.
This patch uses USB core framework usb_hcd_start_port_resume,
usb_hcd_end_port_resume API's in order to autoresume/autosuspend
root hub properly.
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the new get_resuming_ports HCD method to
the xhci-hcd driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_get_ports() is one of the last functions using port_arrays in
xhci-hub.c. We get the same data directly from hub and port structures
instead, so convert and remove both xhci_get_ports() and port_arrays from
all function that no longer need it.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use pointers to port array and port index as function parameters
in xhci_test_and_clear_bit(), just use a pointer to the right port
structure.
xhci_test_and_clear_bit() was the last port_array user in
xhci_get_port_status() and handle_port_status(), so remove the
port_array from them as well.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove old iomem port array and index as parameters, just
send a ponter to a port strucure instread
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use port structures instead of mmio port arrays for
xhci_port_missing_cas_quirk() and xhci_set_remote_wake_mask() in
xhci-hub.c
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new port structures for functions in xhci-hub.c to get
port mmio address of portsc register instead of the port array
xhci_get_port_io_addr() is no longer needeed and is removed.
Plan is to get rid of the mmio port array completely.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
quick way to get the xhci roothub and thus all the ports
belonging to a certain hcd
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hub driver will try to disable a USB3 device twice at logical disconnect,
racing with xhci_free_dev() callback from the first port disable.
This can be triggered with "udisksctl power-off --block-device <disk>"
or by writing "1" to the "remove" sysfs file for a USB3 device
in 4.17-rc4.
USB3 devices don't have a similar disabled link state as USB2 devices,
and use a U3 suspended link state instead. In this state the port
is still enabled and connected.
hub_port_connect() first disconnects the device, then later it notices
that device is still enabled (due to U3 states) it will try to disable
the port again (set to U3).
The xhci_free_dev() called during device disable is async, so checking
for existing xhci->devs[i] when setting link state to U3 the second time
was successful, even if device was being freed.
The regression was caused by, and whole thing revealed by,
Commit 44a182b9d1 ("xhci: Fix use-after-free in xhci_free_virt_device")
which sets xhci->devs[i]->udev to NULL before xhci_virt_dev() returned.
and causes a NULL pointer dereference the second time we try to set U3.
Fix this by checking xhci->devs[i]->udev exists before setting link state.
The original patch went to stable so this fix needs to be applied there as
well.
Fixes: 44a182b9d1 ("xhci: Fix use-after-free in xhci_free_virt_device")
Cc: <stable@vger.kernel.org>
Reported-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Tested-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When disabling a USB3 port the hub driver will set the port link state to
U3 to prevent "ejected" or "safely removed" devices that are still
physically connected from immediately re-enumerating.
If the device was really unplugged, then error messages were printed
as the hub tries to set the U3 link state for a port that is no longer
enabled.
xhci-hcd ee000000.usb: Cannot set link state.
usb usb8-port1: cannot disable (err = -32)
Don't print error message in xhci-hub if hub tries to set port link state
for a disabled port. Return -ENODEV instead which also silences hub driver.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For AMD Promontory xHCI host, although you can disable USB ports in
BIOS settings, those ports will be enabled anyway after you remove a
device on that port and re-plug it in again. It's a known limitation of
the chip. As a workaround we can clear the PORT_WAKE_BITS.
[commit and code comment rephrasing -Mathias]
Signed-off-by: Joe Lee <asmt.swfae@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trace the port status of each port of a roothub when
the xhci roothub receives a Get Hub Status request.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add tracing showing the port status register content each time
the xhci roothub receives a Get Port Status request.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commands with input contexts are allocated with the
xhci_alloc_command_with_ctx helper.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_stop_device() calls xhci_queue_stop_endpoint() multiple times
without checking the return value. xhci_queue_stop_endpoint() can
return error if the HC is already halted or unable to queue commands.
This can cause a deadlock condition as xhci_stop_device() would
end up waiting indefinitely for a completion for the command that
didn't get queued. Fix this by checking the return value and bailing
out of xhci_stop_device() in case of error. This patch happens to fix
potential memory leaks of the allocated command structures as well.
Fixes: c311e391a7 ("xhci: rework command timeout and cancellation,")
Cc: <stable@vger.kernel.org>
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_disable_slot() allows the invoker to pass a command pointer
as paramenter. Otherwise, it will allocate one. This will cause
memory leak when a command structure was allocated inside of this
function while queuing command trb fails. Another problem comes up
when the invoker passed a command pointer, but xhci_disable_slot()
frees it when it detects a dead host.
This patch fixes these two problems by removing the command parameter
from xhci_disable_slot().
Fixes: f9e609b824 ("usb: xhci: Add helper function xhci_disable_slot().")
Cc: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_disable_slot() is a helper for disabling a slot when a device
goes away or recovers from error situations. Currently, it checks
the corespoding virt-dev pointer and returns directly (w/o issuing
disable slot command) if it's null.
This is unnecessary and will cause problems in case where virt-dev
allocation fails and xhci_disable_slot() is called to roll back the
hardware state. Refer to the implementation of xhci_alloc_dev().
This patch removes lines to check virt-dev in xhci_disable_slot().
Fixes: f9e609b824 ("usb: xhci: Add helper function xhci_disable_slot().")
Cc: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit dec08194ff.
Commit dec08194ff ("xhci: Limit USB2 port wake support for AMD Promontory
hosts") makes all high speed USB ports on ASUS PRIME B350M-A cease to
function after enabling runtime PM.
All boards with this chipsets will be affected, so revert the commit.
The original patch was added to stable 4.9, 4.11 and 4.12 and needs
to reverted from there as well
Cc: <stable@vger.kernel.org> # 4.9+
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A SuperSpeedPlus roothub needs to have the Link Protocol (LP) bit set in
the bmSublinkSpeedAttr[] entry of a SuperSpeedPlus descriptor.
If the xhci controller has an optional Protocol Speed ID (PSI) table then
that will be used as a base to create the roothub SuperSpeedPlus
descriptor.
The PSI table does not however necessary contain the LP bit so we need
to set it manually.
Check the psi speed and set LP bit if speed is 10Gbps or higher.
We're not setting it for 5 to 10Gbps as USB 3.1 specification always
mention SuperSpeedPlus for 10Gbps or higher, and some SSIC USB 3.0 speeds
can be over 5Gbps, such as SSIC-G3B-L1 at 5830 Mbps
Cc: <stable@vger.kernel.org> # 4.6+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman