rproc_alloc_firmware() (called by rproc_alloc()) can allocate
rproc->firmware using kstrdup_const() and therefore should be freed
using kfree_const(); however, rproc_set_firmware() frees it using the
simple kfree(). This causes a kernel oops if a constant string is passed
to rproc_alloc() and rproc_set_firmware() is subsequently called.
Fix the above issue by using kfree_const() to free rproc->firmware in
rproc_set_firmware().
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Link: https://lore.kernel.org/r/20210118165904.719999-1-daniele.alessandrelli@linux.intel.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
L1TCM is a high performance memory region in MT8192 SCP.
Reads L1TCM memory region from DTS to determine if the machine supports.
Loads L1TCM memory region to SCP sys if the firmware provides.
Starts from MT8192 SCP, the firmware contains physical addresses for
each memory region, for instance:
Program Headers:
Type Offset VirtAddr PhysAddr FileSiz MemSiz Flg Align
LOAD 0xXXXXXX 0xXXXXXXXX 0x10500000 0xXXXXX 0xXXXXX XXX 0xXXXX
LOAD 0xXXXXXX 0xXXXXXXXX 0x10700000 0xXXXXX 0xXXXXX XXX 0xXXXX
LOAD 0xXXXXXX 0xXXXXXXXX 0x50000000 0xXXXXX 0xXXXXX XXX 0xXXXX
Kernel driver can use the "PhysAddr" (i.e. da in the da_to_va callbacks)
to know the ELF segment belongs to which region.
To backward compatible to MT8183 SCP, separates the da_to_va callbacks
for new and legacy version.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20210127083136.3745652-5-tzungbi@google.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The register MT8192_CORE0_MEM_ATT_PREDEF contains attributes for each
memory region. It defines whether a memory region can be managed by MPU
or not.
In the past, due to the default settings in the register, MT8192 SCP
works luckily. After enabling L1TCM, SCP starts to access memory region
that is not included in the default settings. As a result, SCP hangs.
Enables MPU for all memory regions in MT8192 SCP.
Note that the register is read only once when SCP resets. Thus, it must
be set from kernel side.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20210127083136.3745652-3-tzungbi@google.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Replaces platform_get_resource_byname() and devm_ioremap_resource()
pairs to devm_platform_ioremap_resource_byname().
Note that, not every pairs are applicable to replace. Especially when
it needs to access the resource struct from
platform_get_resource_byname().
For example:
scp->sram_size = resource_size(res);
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20210127083136.3745652-2-tzungbi@google.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add a 'auto_boot' module parameter that instructs the remoteproc driver
whether or not it should auto-boot the remote processor, which will
default to "false", since the VPU in Ingenic SoCs does not really have
any predetermined function.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210123142956.17865-1-paul@crapouillou.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Building the remoteproc drivers into the kernel while the qcom_glink
code is in a loadable module results in a link error:
ld.lld: error: undefined symbol: qcom_glink_ssr_notify
>>> referenced by vmlinux.o:(glink_subdev_unprepare)
Add a Kconfig dependency to avoid this.
Reviewed-by: Alex Elder <elder@linaro.org>
Fixes: 8527efc59d ("rpmsg: glink: Guard qcom_glink_ssr_notify() with correct config")
Fixes: 5d1f2e3c80 ("soc: qcom: glink_ssr: Internalize ssr_notifiers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210204154010.1585457-1-arnd@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error.
The benefit is that DEFER issue will be logged in the devices_deferred
debugfs file.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss-st.com>
Link: https://lore.kernel.org/r/20201217144125.12903-1-arnaud.pouliquen@foss.st.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
With these more help text added, hopefully it's easier to understand the
distinctions of these qcom remoteproc drivers.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20201217030400.6235-1-shawn.guo@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
WCN3660B is a variant of WCN3660, but with the same regulator
requirements as WCN3620/WCN3680. As far as qcom_wcnss_iris is
concerned we can just use qcom,wcn3680 (wcn3680_data).
However, a separate compatible is needed for WCN3660B because
the wcn36xx driver uses it to enable chip-specific functionality.
In particular, it enables 802.11ac for qcom,wcn3680 which is not
supported by WCN3660B.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210106102134.59801-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
There are a couple of subsystems maintained by other people that
merge their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control
and SoC identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660
and SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs.
There is a trivial conflict in the cedrus driver, with two branches
adding the same CEDRUS_CAPABILITY_H265_DEC flag, and another trivial
remove/remove conflict in linux/dma-mapping.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=BjJf
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are a couple of subsystems maintained by other people that merge
their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power
domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control and SoC
identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660 and
SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs"
* tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (222 commits)
soc: mediatek: mmsys: Specify HAS_IOMEM dependency for MTK_MMSYS
firmware: xilinx: Properly align function parameter
firmware: xilinx: Add a blank line after function declaration
firmware: xilinx: Remove additional newline
firmware: xilinx: Fix kernel-doc warnings
firmware: xlnx-zynqmp: fix compilation warning
soc: xilinx: vcu: add missing register NUM_CORE
soc: xilinx: vcu: use vcu-settings syscon registers
dt-bindings: soc: xlnx: extract xlnx, vcu-settings to separate binding
soc: xilinx: vcu: drop useless success message
clk: samsung: mark PM functions as __maybe_unused
soc: samsung: exynos-chipid: initialize later - with arch_initcall
soc: samsung: exynos-chipid: order list of SoCs by name
memory: jz4780_nemc: Fix potential NULL dereference in jz4780_nemc_probe()
memory: ti-emif-sram: only build for ARMv7
memory: tegra30: Support interconnect framework
memory: tegra20: Support hardware versioning and clean up OPP table initialization
dt-bindings: memory: tegra20-emc: Document opp-supported-hw property
soc: rockchip: io-domain: Fix error return code in rockchip_iodomain_probe()
reset-controller: ti: force the write operation when assert or deassert
...
Reads the IPI buffer offset from the FW binary. The information resides
in addr of .ipi_buffer section.
Moves scp_ipi_init() to rproc_ops::parse_fw() phase. The IPI buffer can
be initialized only if the offset is clear.
To backward compatible to MT8183 SCP, specify the offset in the board
specific mtk_scp_of_data. Reads the default offset if the firmware
doesn't have it.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201202044609.2501913-1-tzungbi@google.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
platform_get_resource() may fail and in this case a NULL dereference
will occur.
Fix it to use devm_platform_ioremap_resource() instead of calling
platform_get_resource() and devm_ioremap().
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = \(platform_get_resource\|platform_get_resource_byname\)(pdev, t,
n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Fixes: dc160e4491 ("remoteproc: qcom: Introduce Non-PAS ADSP PIL driver")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1607392460-20516-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In case of error, the function devm_ioremap_wc() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Fixes: 6edbe024ba ("remoteproc: k3-dsp: Add a remoteproc driver of K3 C66x DSPs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20200905122503.17352-1-yuehaibing@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
If the pm_runtime_get_sync failed in adsp_pds_enable when
loop (i), The unroll_pd_votes will start from (i - 1), and
it will resulted in following problems:
1) pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak.
2) Have not reset pds[i] performance state.
Then we fix it.
Fixes: 17ee2fb4e8 ("remoteproc: qcom: pas: Vote for active/proxy power domains")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201102143554.144707-1-zhangqilong3@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak in adsp_start, so we should fix it.
Fixes: dc160e4491 ("remoteproc: qcom: Introduce Non-PAS ADSP PIL driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201102143534.144484-1-zhangqilong3@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
If the pm_runtime_get_sync failed in q6v5_pds_enable when
loop (i), The unroll_pd_votes will start from (i - 1), and
it will resulted in following problems:
1) pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak.
2) Have not reset pds[i] performance state.
Then we fix it.
Fixes: 4760a896be ("remoteproc: q6v5-mss: Vote for rpmh power domains")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201102143433.143996-1-zhangqilong3@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Now that this driver can be compiled with COMPILE_TEST, we have no
guarantee that CONFIG_OF will also be defined. When that happens, a
warning about mtk_scp_of_match being defined but unused will be reported
so make sure this variable is only defined if of_match_ptr() actually
uses it.
Fixes: cbd2dca749 remoteproc: scp: add COMPILE_TEST dependency
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Link: https://lore.kernel.org/r/20201102074007.299222-1-acourbot@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add minidump id for modem in sm8150 chipset so that the regions to be
included in the coredump generated upon a crash is based on the minidump
tables in SMEM instead of those in the ELF header.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by, Reviewed-by or Tested-by that you received previously.:
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1605819935-10726-5-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch adds support for collecting minidump in the event of remoteproc
crash. Parse the minidump table based on remoteproc's unique minidump-id,
read all memory regions from the remoteproc's minidump table entry and
expose the memory to userspace. The remoteproc platform driver can choose
to collect a full/mini dump by specifying the coredump op.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Co-developed-by: Gurbir Arora <gurbaror@codeaurora.org>
Signed-off-by: Gurbir Arora <gurbaror@codeaurora.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1605819935-10726-4-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This change adds a new kind of core dump mechanism which instead of dumping
entire program segments of the firmware, dumps sections of the remoteproc
memory which are sufficient to allow debugging the firmware. This function
thus uses section headers instead of program headers during creation of the
core dump elf.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1605819935-10726-3-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Each remoteproc might have different requirements for coredumps and might
want to choose the type of dumps it wants to collect. This change allows
remoteproc drivers to specify their own custom dump function to be executed
in place of rproc_coredump. If the coredump op is not specified by the
remoteproc driver it will be set to rproc_coredump by default.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Link: https://lore.kernel.org/r/1605819935-10726-2-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The K3 J721E family of SoCs have a revised version of the AM65x ICSSG IP
and contains two instances of this newer ICSSG IP. Each ICSSG processor
subsystem contains 2 primary PRU cores, 2 auxiliary PRU cores called RTUs,
and 2 new auxiliary cores called Transmit PRUs (Tx_PRUs).
Enhance the existing PRU remoteproc driver to support these new PRU
and RTU cores by using specific compatibles. The cores have the same
memory copying limitations as on AM65x, so reuses the custom memcpy
function within the driver's ELF loader implementation. The initial
names for the firmware images for each PRU core are retrieved from
DT nodes, and can be adjusted through sysfs if required.
Signed-off-by: Suman Anna <s-anna@ti.com>
Co-developed-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201208141002.17777-7-grzegorz.jaszczyk@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The K3 AM65x family of SoCs have the next generation of the PRU-ICSS
processor subsystem, commonly referred to as ICSSG. Each ICSSG processor
subsystem on AM65x SR1.0 contains two primary PRU cores and two new
auxiliary PRU cores called RTUs. The AM65x SR2.0 SoCs have a revised
ICSSG IP that is based off the subsequent IP revision used on J721E
SoCs. This IP instance has two new custom auxiliary PRU cores called
Transmit PRUs (Tx_PRUs) in addition to the existing PRUs and RTUs.
Each RTU and Tx_PRU cores have their own dedicated IRAM (smaller than
a PRU), Control and debug feature sets, but is different in terms of
sub-modules integrated around it and does not have the full capabilities
associated with a PRU core. The RTU core is typically used to aid a
PRU core in accelerating data transfers, while the Tx_PRU cores is
normally used to control the TX L2 FIFO if enabled in Ethernet
applications. Both can also be used to run independent applications.
The RTU and Tx_PRU cores though share the same Data RAMs as the PRU
cores, so the memories have to be partitioned carefully between different
applications. The new cores also support a new sub-module called Task
Manager to support two different context thread executions.
Enhance the existing PRU remoteproc driver to support these new PRU, RTU
and Tx PRU cores by using specific compatibles. The initial names for the
firmware images for each PRU core are retrieved from DT nodes, and can
be adjusted through sysfs if required.
The PRU remoteproc driver has to be specifically modified to use a
custom memcpy function within its ELF loader implementation for these
new cores in order to overcome a limitation with copying data into each
of the core's IRAM memories. These memory ports support only 4-byte
writes, and any sub-word order byte writes clear out the remaining
bytes other than the bytes being written within the containing word.
The default ARM64 memcpy also cannot be used as it throws an exception
when the preferred 8-byte copy operation is attempted. This choice is
made by using a state flag that is set only on K3 SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Co-developed-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201208141002.17777-6-grzegorz.jaszczyk@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The remoteproc core creates certain standard debugfs entries,
that does not give a whole lot of useful information for the
PRUs. The PRU remoteproc driver is enhanced to add additional
debugfs entries for PRU. These will be auto-cleaned up when
the parent rproc debug directory is removed.
The enhanced debugfs support adds two new entries: 'regs' and
'single_step'. The 'regs' dumps out the useful CTRL sub-module
registers as well as each of the 32 GPREGs and CT_REGs registers.
The GPREGs and CT_REGs though are printed only when the PRU is
halted and accessible as per the IP design.
The 'single_step' utilizes the single-step execution of the PRU
cores. Writing a non-zero value performs a single step, and a
zero value restores the PRU to execute in the same mode as the
mode before the first single step. (note: if the PRU is halted
because of a halt instruction, then no change occurs).
Logic for setting the PC and jumping over a halt instruction shall
be added in the future.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201208141002.17777-5-grzegorz.jaszczyk@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The firmware blob can contain optional ELF sections: .resource_table
section and .pru_irq_map one. The second one contains the PRUSS
interrupt mapping description, which needs to be setup before powering
on the PRU core. To avoid RAM wastage this ELF section is not mapped to
any ELF segment (by the firmware linker) and therefore is not loaded to
PRU memory.
The PRU interrupt configuration is handled within the PRUSS INTC irqchip
driver and leverages the system events to interrupt channels and host
interrupts mapping configuration. Relevant irq routing information is
passed through a special .pru_irq_map ELF section (for interrupts routed
to and used by PRU cores) or via the PRU application's device tree node
(for interrupts routed to and used by the main CPU). The mappings are
currently programmed during the booting/shutdown of the PRU.
The interrupt configuration passed through .pru_irq_map ELF section is
optional. It varies on specific firmware functionality and therefore
have to be unwinded during PRU stop and performed again during
PRU start.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Co-developed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Link: https://lore.kernel.org/r/20201208141002.17777-4-grzegorz.jaszczyk@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Programmable Real-Time Unit Subsystem (PRUSS) consists of
dual 32-bit RISC cores (Programmable Real-Time Units, or PRUs)
for program execution. This patch adds a remoteproc platform
driver for managing the individual PRU RISC cores life cycle.
The PRUs do not have a unified address space (have an Instruction
RAM and a primary Data RAM at both 0x0). The PRU remoteproc driver
therefore uses a custom remoteproc core ELF loader ops. The added
.da_to_va ops is only used to provide translations for the PRU
Data RAMs. This remoteproc driver does not have support for error
recovery and system suspend/resume features. Different compatibles
are used to allow providing scalability for instance-specific device
data if needed. The driver uses a default firmware-name retrieved
from device-tree for each PRU core, and the firmwares are expected
to be present in the standard Linux firmware search paths. They can
also be adjusted by userspace if required through the sysfs interface
provided by the remoteproc core.
The PRU remoteproc driver uses a client-driven boot methodology: it
does _not_ support auto-boot so that the PRU load and boot is dictated
by the corresponding client drivers for achieving various usecases.
This allows flexibility for the client drivers or applications to set
a firmware name (if needed) based on their desired functionality and
boot the PRU. The sysfs bind and unbind attributes have also been
suppressed so that the PRU devices cannot be unbound and thereby
shutdown a PRU from underneath a PRU client driver.
The driver currently supports the AM335x, AM437x, AM57xx and 66AK2G
SoCs, and support for other TI SoCs will be added in subsequent
patches.
Co-developed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Co-developed-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20201208141002.17777-3-grzegorz.jaszczyk@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The latest version of sysmon_stop() starts by initializing
the sysmon->shutdown_acked variable, but then overwrites it
with an uninitialized variable later:
drivers/remoteproc/qcom_sysmon.c:551:11: error: variable 'acked' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized]
else if (sysmon->ept)
^~~~~~~~~~~
drivers/remoteproc/qcom_sysmon.c:554:27: note: uninitialized use occurs here
sysmon->shutdown_acked = acked;
^~~~~
Remove the local 'acked' variable again and set the state directly.
Fixes: 5c212aaf54 ("remoteproc: sysmon: Expose the shutdown result")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201204193740.3162065-1-arnd@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The J7200 SoCs have a revised R5FSS IP that adds a unique feature w.r.t
TCM sizing. Each R5F core in a cluster typically has 32 KB each of ATCM
and BTCM, with only the Core0 TCMs usable in LockStep mode. This revised
IP however doubles the total available TCM in LockStep mode by making the
Core1 TCM visible immediately after the corresponding Core0 TCM.
The R5F DT nodes on the J7200 SoCs define double (64 KB) the normal TCM
size (32 KB) for R5F Core0 for each of ATCM and BTCM to represent the
above. This increased TCM memory is only usable in LockStep-mode, and
has to be adjusted to the normal 32 KB size in Split mode. Enhance the
TI K3 R5F remoteproc for this logic through a new function. The adjustment
is a no-op on prior SoCs and relies on the correct DTS node sizes in
LockStep-mode on applicable SoCs.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20201119010531.21083-4-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The K3 J7200 SoC family has a revised R5F sub-system and contains a
subset of the R5F clusters present on J721E SoCs. The K3 J7200 SoCs
only have two dual-core Arm R5F clusters/subsystems with 2 R5F cores
each. One cluster is present within the MCU voltage domain (MCU_R5FSS0),
while the other is present in the MAIN voltage domain (MAIN_R5FSS0).
The revised IP has the following two new features:
1. TCMs are auto-initialized during module power-up, and the behavior
is programmable through a MMR bit.
2. The LockStep-mode allows the Core1 TCMs to be combined with the
Core0 TCMs effectively doubling the amount of TCMs available.
The LockStep-mode on previous SoCs could only use the Core0 TCMs.
This combined TCMs appear contiguous at the respective Core0 TCM
addresses.
Extend the support to these clusters in the K3 R5F remoteproc driver
using J7200 specific compatibles. Logic for the second feature is
added in the next patch. The integration of these clusters is very
much similar to J721E SoCs otherwise.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20201119010531.21083-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A new API, rproc_set_firmware() is added to allow the remoteproc platform
drivers and remoteproc client drivers to be able to configure a custom
firmware name that is different from the default name used during
remoteproc registration. This function is being introduced to provide
a kernel-level equivalent of the current sysfs interface to remoteproc
client drivers, and can only change firmwares when the remoteproc is
offline. This allows some remoteproc drivers to choose different firmwares
at runtime based on the functionality the remote processor is providing.
The TI PRU Ethernet driver will be an example of such usage as it
requires to use different firmwares for different supported protocols.
Also, update the firmware_store() function used by the sysfs interface
to reuse this function to avoid code duplication.
Reviewed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20201121032042.6195-1-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Improve the style of a few of the error messages printed by the sysmon
implementation and fix the copy-pasted shutdown error in the send-event
function.
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/20201122054135.802935-5-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Requesting a graceful shutdown through the shared memory state signals
will not be acked in the event that sysmon has already successfully shut
down the remote firmware. So extend the stop request API to optionally
take the remoteproc's sysmon instance and query if there's already been
a successful shutdown attempt, before doing the signal dance.
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/20201122054135.802935-4-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A graceful shutdown of the Qualcomm remote processors where
traditionally performed by invoking a shared memory state signal and
waiting for the associated ack.
This was later superseded by the "sysmon" mechanism, where some form of
shared memory bus is used to send a "graceful shutdown request" message
and one of more signals comes back to indicate its success.
But when this newer mechanism is in effect the firmware is shut down by
the time the older mechanism, implemented in the remoteproc drivers,
attempts to perform a graceful shutdown - and as such it will never
receive an ack back.
This patch therefor track the success of the latest shutdown attempt in
sysmon and exposes a new function in the API that the remoteproc driver
can use to query the success and the necessity of invoking the older
mechanism.
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/20201122054135.802935-3-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The reliance on the remoteproc's state for determining when to send
sysmon notifications to a remote processor is racy with regard to
concurrent remoteproc operations.
Further more the advertisement of the state of other remote processor to
a newly started remote processor might not only send the wrong state,
but might result in a stream of state changes that are out of order.
Address this by introducing state tracking within the sysmon instances
themselves and extend the locking to ensure that the notifications are
consistent with this state.
Fixes: 1f36ab3f6e ("remoteproc: sysmon: Inform current rproc about all active rprocs")
Fixes: 1877f54f75 ("remoteproc: sysmon: Add notifications for events")
Fixes: 1fb82ee806 ("remoteproc: qcom: Introduce sysmon")
Cc: stable@vger.kernel.org
Reviewed-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Link: https://lore.kernel.org/r/20201122054135.802935-2-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The application processor accessing the MBA region after assigning it to
the remote Q6 would lead to an XPU violation. Fix this by un-mapping the
MBA region post firmware copy and MBA text log dumps.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/1604473422-29639-2-git-send-email-sibis@codeaurora.org
[bjorn: Renamed "ptr" to "mba_region"]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fix the sparse warnings reported by the kernel test bot by replacing
ioremap calls with memremap.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/1604473422-29639-1-git-send-email-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The only usage of qmi_indication_handler[] is to pass its address to
qmi_handle_init() which accepts a const pointer. Make it const to allow
the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20201122234540.34623-1-rikard.falkeborn@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The main purpose of the loop is to load the memory to the SCP SRAM.
If filesz is 0, can go to next program header directly.
We don't need to try to validate the FW binary for those filesz==0
segments.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201116084413.3312631-3-tzungbi@google.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
It is valid if offset+length == sram_size.
For example, sram_size=100, offset=99, length=1. Accessing offset 99
with length 1 is valid.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201116084413.3312631-2-tzungbi@google.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes the following sparse errors on dma_alloc_coherent() and
dma_free_coherent().
On drivers/remoteproc/mtk_scp.c:559:23:
warning: incorrect type in assignment (different address spaces)
expected void [noderef] __iomem *cpu_addr
got void *
On drivers/remoteproc/mtk_scp.c:572:56:
warning: incorrect type in argument 3 (different address spaces)
expected void *cpu_addr
got void [noderef] __iomem *cpu_addr
The cpu_addr is not a __iomem address. Removes the marker.
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201116082537.3287009-3-tzungbi@google.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The only usage of st_rproc_ops is to pass its address to rproc_alloc()
which accepts a const pointer. Make it const to allow the compiler to
put it in read-only memory.
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20201107233630.9728-3-rikard.falkeborn@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The only usage of ingenic_rproc_ops is to pass its address to
devm_rproc_alloc(), which accepts a const pointer. Make it const to
allow the compiler to put it in read-only memory.
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20201107233630.9728-2-rikard.falkeborn@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
