[ Upstream commit f86f58e359 ]
According to the SGTL5000 datasheet [1], the DAP_AVC_CTRL register has
the following bit field definitions:
| BITS | FIELD | RW | RESET | DEFINITION |
| 15 | RSVD | RO | 0x0 | Reserved |
| 14 | RSVD | RW | 0x1 | Reserved |
| 13:12 | MAX_GAIN | RW | 0x1 | Max Gain of AVC in expander mode |
| 11:10 | RSVD | RO | 0x0 | Reserved |
| 9:8 | LBI_RESP | RW | 0x1 | Integrator Response |
| 7:6 | RSVD | RO | 0x0 | Reserved |
| 5 | HARD_LMT_EN | RW | 0x0 | Enable hard limiter mode |
| 4:1 | RSVD | RO | 0x0 | Reserved |
| 0 | EN | RW | 0x0 | Enable/Disable AVC |
The original default value written to the DAP_AVC_CTRL register during
sgtl5000_i2c_probe() was 0x0510. This would incorrectly write values to
bits 4 and 10, which are defined as RESERVED. It would also not set
bits 12 and 14 to their correct RESET values of 0x1, and instead set
them to 0x0. While the DAP_AVC module is effectively disabled because
the EN bit is 0, this default value is still writing invalid values to
registers that are marked as read-only and RESERVED as well as not
setting bits 12 and 14 to their correct default values as defined by the
datasheet.
The correct value that should be written to the DAP_AVC_CTRL register is
0x5100, which configures the register bits to the default values defined
by the datasheet, and prevents any writes to bits defined as
'read-only'. Generally speaking, it is best practice to NOT attempt to
write values to registers/bits defined as RESERVED, as it generally
produces unwanted/undefined behavior, or errors.
Also, all credit for this patch should go to my colleague Dan MacDonald
<dmacdonald@curbellmedical.com> for finding this error in the first
place.
[1] https://www.nxp.com/docs/en/data-sheet/SGTL5000.pdf
Signed-off-by: Benjamin Rood <benjaminjrood@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210219183308.GA2117@ubuntu-dev
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eee51df776 ]
The adc_vol_tlv volume-control has a range from -17.625 dB to +30 dB,
not -176.25 dB to + 300 dB. This wrong scale is esp. a problem in userspace
apps which translate the dB scale to a linear scale. With the logarithmic
dB scale being of by a factor of 10 we loose all precision in the lower
area of the range when apps translate things to a linear scale.
E.g. the 0 dB default, which corresponds with a value of 47 of the
0 - 127 range for the control, would be shown as 0/100 in alsa-mixer.
Since the centi-dB values used in the TLV struct cannot represent the
0.375 dB step size used by these controls, change the TLV definition
for them to specify a min and max value instead of min + stepsize.
Note this mirrors commit 3f31f7d9b5 ("ASoC: rt5670: Fix dac- and adc-
vol-tlv values being off by a factor of 10") which made the exact same
change to the rt5670 codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210226143817.84287-3-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfa26ed1f9 ]
The adc_vol_tlv volume-control has a range from -17.625 dB to +30 dB,
not -176.25 dB to + 300 dB. This wrong scale is esp. a problem in userspace
apps which translate the dB scale to a linear scale. With the logarithmic
dB scale being of by a factor of 10 we loose all precision in the lower
area of the range when apps translate things to a linear scale.
E.g. the 0 dB default, which corresponds with a value of 47 of the
0 - 127 range for the control, would be shown as 0/100 in alsa-mixer.
Since the centi-dB values used in the TLV struct cannot represent the
0.375 dB step size used by these controls, change the TLV definition
for them to specify a min and max value instead of min + stepsize.
Note this mirrors commit 3f31f7d9b5 ("ASoC: rt5670: Fix dac- and adc-
vol-tlv values being off by a factor of 10") which made the exact same
change to the rt5670 codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210226143817.84287-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a14a621999 ]
On some Lenovo systems if the microphone is disabled in the BIOS
only the NHLT table header is created, with no data. This means
the endpoints field is not correctly set to zero - leading to an
unintialised variable and hence invalid descriptors are parsed
leading to page faults.
The Lenovo firmware team is addressing this, but adding a check
preventing invalid tables being parsed is worthwhile.
Tested on a Lenovo T14.
Tested-by: Philipp Leskovitz <philipp.leskovitz@secunet.com>
Reported-by: Philipp Leskovitz <philipp.leskovitz@secunet.com>
Signed-off-by: Mark Pearson <markpearson@lenovo.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302141003.7342-1-markpearson@lenovo.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 50b1affc89 upstream.
The shifting of the u8 integer device by 24 bits to the left will
be promoted to a 32 bit signed int and then sign-extended to a
64 bit unsigned long. In the event that the top bit of device is
set then all then all the upper 32 bits of the unsigned long will
end up as also being set because of the sign-extension. Fix this
by casting device to an unsigned long before the shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes: a07df82c79 ("ALSA: usb-audio: Add DJM750 to Pioneer mixer quirk")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210318132008.15266-1-colin.king@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ca88d5335 upstream.
This reverts commit 1e30f642cf ("ASoC: simple-card-utils: Fix device
module clock"). The original patch ended up breaking following platform,
which depends on set_sysclk() to configure internal PLL on wm8904 codec
and expects simple-card-utils to not update the MCLK rate.
- "arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var3-ads2.dts"
It would be best if codec takes care of setting MCLK clock via DAI
set_sysclk() callback.
Reported-by: Michael Walle <michael@walle.cc>
Suggested-by: Mark Brown <broonie@kernel.org>
Suggested-by: Michael Walle <michael@walle.cc>
Fixes: 1e30f642cf ("ASoC: simple-card-utils: Fix device module clock")
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Tested-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/1615829492-8972-2-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9922f50f71 upstream.
The max boundary check while parsing dai ids makes
sound card registration fail after common up dai ids.
Fixes: cd3484f7f1 ("ASoC: qcom: Fix broken support to MI2S TERTIARY and QUATERNARY")
Signed-off-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Link: https://lore.kernel.org/r/20210311154557.24978-1-srivasam@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3bb4852d59 upstream.
set channel map can be passed with a channel maps, however if
the number of channels that are passed are more than the actual
supported channels then we would be accessing array out of bounds.
So add a sanity check to validate these numbers!
Fixes: a61f3b4f47 ("ASoC: wcd934x: add support to wcd9340/wcd9341 codec")
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210309142129.14182-4-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4800fe6ea1 upstream.
WCD934x has only 13 RX SLIM ports however we are setting it as 16
in set_channel_map, this will lead to array out of bounds error!
Orignally caught by enabling USBAN array out of bounds check:
Fixes: 5caf64c633 ("ASoC: qcom: sdm845: add support to DB845c and Lenovo Yoga")
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210309142129.14182-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c668e1c0a upstream.
Static analysis Coverity had detected a potential array out-of-bounds
write issue due to the fact that MAX AFE port Id was set to 16 instead
of using AFE_PORT_MAX macro.
Fix this by properly using AFE_PORT_MAX macro.
Fixes: 1b93a88431 ("ASoC: qcom: sdm845: handle soundwire stream")
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210309142129.14182-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd82991819 upstream.
The ADSPCS_SPA is Set Power Active bit. To check if DSP is powered
down, we need to check ADSPCS_CPA, the Current Power Active bit.
Fixes: 747503b181 ("ASoC: SOF: Intel: Add Intel specific HDA DSP HW operations")
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pan Xiuli <xiuli.pan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210309004127.4940-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5bb0ecddb2 upstream.
We only unregister the platform device during the .remove operation,
but if the probe fails we will never reach this sequence.
Suggested-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Fixes: dd96daca6c ("ASoC: SOF: Intel: Add APL/CNL HW DSP support")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210302003410.1178535-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca08ddfd96 upstream.
When I added the quirk for the "HP Pavilion x2 10-p0XX" I copied the
byt_rt5640_quirk_table[] entry for the HP Pavilion x2 10-k0XX / 10-n0XX
models since these use almost the same settings.
While doing this I accidentally also copied and kept the non-standard
OVCD_TH_1500UA setting used on those models. This too low threshold is
causing headsets to often be seen as headphones (without a headset-mic)
and when correctly identified it is causing ghost play/pause
button-presses to get detected.
Correct the HP Pavilion x2 10-p0XX quirk to use the default OVCD_TH_2000UA
setting, fixing these problems.
Fixes: fbdae7d6d0 ("ASoC: Intel: bytcr_rt5640: Fix HP Pavilion x2 Detachable quirks")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210224105052.42116-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8726396851 upstream.
When using the driver in I2S TDM mode, the _fsl_ssi_set_dai_fmt()
function rewrites the number of slots previously set by the
fsl_ssi_set_dai_tdm_slot() function to 2 by default.
To fix this, let's use the saved slot count value or, if TDM
is not used and the slot count is not set, proceed as before.
Fixes: 4f14f5c11d ("ASoC: fsl_ssi: Fix number of words per frame for I2S-slave mode")
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20210216114221.26635-1-shc_work@mail.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53b861bec7 upstream.
The HP EliteBook 850 G8 Notebook PC is using ALC285 codec which is
using 0x04 to control mute LED and 0x01 to control micmute LED.
Therefore, add a quirk to make it works.
Signed-off-by: Jeremy Szu <jeremy.szu@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210316094236.89028-1-jeremy.szu@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7d66cf799 upstream.
The HP EliteBook 840 G8 Notebook PC is using ALC236 codec which is
using 0x02 to control mute LED and 0x01 to control micmute LED.
Therefore, add a quirk to make it works.
Signed-off-by: Jeremy Szu <jeremy.szu@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210316074626.79895-1-jeremy.szu@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca6883393f upstream.
The HP EliteBook 840 G8 Notebook PC is using ALC285 codec which is
using 0x04 to control mute LED and 0x01 to control micmute LED.
Therefore, add a quirk to make it works.
Signed-off-by: Jeremy Szu <jeremy.szu@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210316065452.75659-1-jeremy.szu@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1c86210fe upstream.
There is another fix for headset-mic problem on Redmibook (1d72:1602),
it also works on Redmibook Air (1d72:1947), which has the same issue.
Signed-off-by: Xiaoliang Yu <yxl_22@outlook.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/TYBP286MB02856DC016849DEA0F9B6A37EE6F9@TYBP286MB0285.JPNP286.PROD.OUTLOOK.COM
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2bf44e0ee9 upstream.
Recently we found the micmute led init state is not correct after
freshly installing the ubuntu linux on a Lenovo AIO machine. The
internal mic is not muted, but the micmute led is on and led mode is
'follow mute'. If we mute internal mic, the led is keeping on, then
unmute the internal mic, the led is off. And from then on, the
micmute led will work correctly.
So the micmute led init state is not correct. The led is controlled
by codec gpio (ALC233_FIXUP_LENOVO_LINE2_MIC_HOTKEY), in the
patch_realtek, the gpio data is set to 0x4 initially and the led is
on with this data. In the hda_generic, the led_value is set to
0 initially, suppose users set the 'capture switch' to on from
user space and the micmute led should change to be off with this
operation, but the check "if (val == spec->micmute_led.led_value)" in
the call_micmute_led_update() will skip the led setting.
To guarantee the led state will be set by the 1st time of changing
"Capture Switch", set -1 to the init led_value.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20210312041408.3776-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b95bc12e04 upstream.
Built-in microphone and combojack on Xiaomi Notebook Pro (1d72:1701) needs
to be fixed, the existing quirk for Dell works well on that machine.
Signed-off-by: Xiaoliang Yu <yxl_22@outlook.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/OS0P286MB02749B9E13920E6899902CD8EE6C9@OS0P286MB0274.JPNP286.PROD.OUTLOOK.COM
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd7b836d6b upstream.
When node is removed from IEEE 1394 bus, any transaction fails to the node.
In the case, ALSA dice driver doesn't stop isochronous contexts even if
they are running. As a result, null pointer dereference occurs in callback
from the running context.
This commit fixes the bug to release isochronous contexts always.
Cc: <stable@vger.kernel.org> # v5.4 or later
Fixes: e9f21129b8 ("ALSA: dice: support AMDTP domain")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210312093407.23437-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80cffd2468 upstream.
Add missed MODULE_DEVICE_TABLE for the driver can be loaded
automatically at boot.
Fixes: 9208847774 ("ASoC: ak5558: Add support for AK5558 ADC driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1614149872-25510-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ec5b96775 upstream.
Add missed MODULE_DEVICE_TABLE for the driver can be loaded
automatically at boot.
Fixes: 08660086ef ("ASoC: ak4458: Add support for AK4458 DAC driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1614149872-25510-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 257d2d7e9e upstream
In the later patch, we're going to issue the PCM sync_stop calls at
disconnection. But currently the USB-audio driver can't handle it
because it has a check of shutdown flag for stopping the URBs. This
is basically superfluous (the stopping URBs are safe at disconnection
state), so let's drop the check.
Fixes: dc5eafe778 ("ALSA: usb-audio: Support PCM sync_stop")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210206203052.15606-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5aa956eae upstream.
The problem was in wrong "if" placement. chip->quirk_type is freed
in snd_card_free_when_closed(), but inside if statement it's accesed.
Fixes: 9799110825 ("ALSA: usb-audio: Disable USB autosuspend properly in setup_disable_autosuspend()")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/16da19126ff461e5e64a9aec648cce28fb8ed73e.1615242183.git.paskripkin@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9799110825 upstream.
Rear audio on Lenovo ThinkStation P620 stops working after commit
1965c4364b ("ALSA: usb-audio: Disable autosuspend for Lenovo
ThinkStation P620"):
[ 6.013526] usbcore: registered new interface driver snd-usb-audio
[ 6.023064] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.023083] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.023090] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.023098] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.023103] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.023110] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.045846] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.045866] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.045877] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.045886] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
[ 6.045894] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x100, wIndex = 0x0, type = 1
[ 6.045908] usb 3-6: cannot get ctl value: req = 0x81, wValue = 0x202, wIndex = 0x0, type = 4
I overlooked the issue because when I was working on the said commit,
only the front audio is tested. Apology for that.
Changing supports_autosuspend in driver is too late for disabling
autosuspend, because it was already used by USB probe routine, so it can
break the balance on the following code that depends on
supports_autosuspend.
Fix it by using usb_disable_autosuspend() helper, and balance the
suspend count in disconnect callback.
Fixes: 1965c4364b ("ALSA: usb-audio: Disable autosuspend for Lenovo ThinkStation P620")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210304043419.287191-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06abcb18b3 upstream.
Other Plantronics headset models seem requiring the same workaround as
C320-M to add the 20ms delay for the control messages, too. Apply the
workaround generically for devices with the vendor ID 0x047f.
Note that the problem didn't surface before 5.11 just with luck.
Since 5.11 got a big code rewrite about the stream handling, the
parameter setup procedure has changed, and this seemed triggering the
problem more often.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1182552
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210304085009.4770-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ff9dde42e upstream.
When HD-audio bus receives unsolicited events during its system
suspend/resume (S3 and S4) phase, the controller driver may still try
to process events although the codec chips are already (or yet)
powered down. This might screw up the codec communication, resulting
in CORB/RIRB errors. Such events should be rather skipped, as the
codec chip status such as the jack status will be fully refreshed at
the system resume time.
Since we're tracking the system suspend/resume state in codec
power.power_state field, let's add the check in the common unsol event
handler entry point to filter out such events.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1182377
Tested-by: Abhishek Sahu <abhsahu@nvidia.com>
Cc: <stable@vger.kernel.org> # 183ab39eb0: ALSA: hda: Initialize power_state
Link: https://lore.kernel.org/r/20210310112809.9215-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13661fc484 upstream.
The HD-audio controller driver processes the unsolicited events via
its work asynchronously, and this might be pending when the system
goes to suspend. When a lengthy event handling like ELD byte reads is
running, this might trigger unexpected accesses among suspend/resume
procedure, typically seen with Nvidia driver that still requires the
handling via unsolicited event verbs for ELD updates.
This patch adds the flush of unsol_work to assure that pending events
are processed before going into suspend.
Buglink: https://bugzilla.suse.com/show_bug.cgi?id=1182377
Reported-and-tested-by: Abhishek Sahu <abhsahu@nvidia.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210310112809.9215-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28e96c1693 upstream.
The commit c02f77d32d ("ALSA: hda - Workaround for crackled sound on
AMD controller (1022:1457)") introduced a few workarounds for the
recent AMD HD-audio controller, and one of them is the forced BATCH
PCM mode so that PulseAudio avoids the timer-based scheduling. This
was thought to cover for some badly working applications, but this
actually worsens for more others. In total, this wasn't a good idea
to enforce it.
This is a partial revert of the commit above for dropping the PCM
BATCH enforcement part to recover from the regression again.
Fixes: c02f77d32d ("ALSA: hda - Workaround for crackled sound on AMD controller (1022:1457)")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=195303
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210308160726.22930-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f15c5c11ab upstream.
The new AE-5 Plus model has a different Subsystem ID compared to the
non-plus model. Adding the new id to the list of quirks.
Signed-off-by: Simeon Simeonoff <sim.simeonoff@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/998cafbe10b648f724ee33570553f2d780a38963.camel@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56b26497bb upstream.
The mute and mic-mute LEDs on HP ZBook Studio G5 are controlled via
GPIO bits 0x10 and 0x20, respectively, and we need the extra setup for
those.
As the similar code is already present for other HP models but with
different GPIO pins, this patch factors out the common helper code and
applies those GPIO values for each model.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211893
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210306095018.11746-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eea46a0879 upstream.
The per_pin->work might be still floating at the suspend, and this may
hit the access to the hardware at an unexpected timing. Cancel the
work properly at the suspend callback for avoiding the buggy access.
Note that the bug doesn't trigger easily in the recent kernels since
the work is queued only when the repoll count is set, and usually it's
only at the resume callback, but it's still possible to hit in
theory.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1182377
Reported-and-tested-by: Abhishek Sahu <abhsahu@nvidia.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210310112809.9215-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc7c5c208e upstream.
The microphone in the Plantronics C320-M headset will randomly
fail to initialize properly, at least when using Microsoft Teams.
Introducing a 20ms delay on the control messages appears to
resolve the issue.
Link: https://gitlab.freedesktop.org/pulseaudio/pulseaudio/-/issues/1065
Tested-by: Andreas Kempe <kempe@lysator.liu.se>
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210303181405.39835-1-john.ernberg@actia.se
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d92e279dee ]
This set of devices has SoundWire support along with DMICs.
The DMI information was provided by users for 3 separate skus.
BugLink: https://github.com/thesofproject/linux/issues/2700
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210208233336.59449-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d09cf8d0d ]
The quirk table is a mess, let's reorganize it by generation before
making sure that the quirks are consistent for each generation.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210208233336.59449-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fee03efc69 ]
This commit adds mixer quirks for the Pioneer DJM-900NXS2 mixer. This
device has 6 capture channels, 5 of them allow setting the signal
source. This adds controls for these, similar to the DJM-250Mk2.
However, playpack channels are not controllable via software like on the
250Mk2, as they can only be set manually on the mixing console.
Read-only controls showing the currently selected playback channels are
omitted.
Signed-off-by: Fabian Lesniak <fabian@lesniak-it.de>
Link: https://lore.kernel.org/r/20210205215116.258724-2-fabian@lesniak-it.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a07df82c79 ]
This allows for N different devices to use the pioneer mixer quirk for
setting capture/record type and recording level. The impementation has
not changed much with the exception of an additional mask on
private_value to allow storing of a device index:
DEVICE MASK 0xff000000
GROUP_MASK 0x00ff0000
VALUE_MASK 0x0000ffff
This could be improved by changing the arrays of wValues for each
channel to contain named definitions (e.g. SND_DJM_CAP_LINE). It would
improve readability and perhaps would allow using the same array for
multiple channels. The channel number can be specified on the control
next to the wIndex.
Feedback is very much appreciated as I'm not the most proficient C
programmer but am learning as I go.
Signed-off-by: Olivia Mackintosh <livvy@base.nu>
Link: https://lore.kernel.org/r/20210205184256.10201-2-livvy@base.nu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45c92ec32b ]
We missed adding the TGL_HDMI quirk which is very much needed to
expose the 4 display pipelines and will be required on TGL topologies.
Fixes: 488cdbd893 ('ASoC: Intel: sof_sdw: add quirk for new TigerLake-SDCA device')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210204203312.27112-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1bea2256aa ]
Tha ARCHOS Cesium 140 tablet has problem with the jack-sensing,
thus the heaset functions are not working.
Add quirk for this model to select the correct input map, jack-detect
options and channel map to enable jack sensing and headset microphone.
This device uses IN1 for its internal MIC and JD2 for jack-detect.
Signed-off-by: Chris Chiu <chiu@endlessos.org>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201208060414.27646-1-chiu@endlessos.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 488cdbd893 ]
Add quirks for jack detection, rt715 DAI and number of speakers.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Link: https://lore.kernel.org/r/20201111214318.150529-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
In v5.10, the "haswell" driver was replaced by the "catpt" driver, but
the mutual exclusion with the SOF driver was not updated. This leads
to errors with card names and UCM profiles not being loaded by
PulseAudio.
This fix should only be applied on v5.10-stable, the mutual exclusion
was removed in 5.11.
Reported-by: David Ward <david.ward@ll.mit.edu>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=211985
Fixes: 6cbfa11d26 ("ASoC: Intel: Select catpt and deprecate haswell")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a864e8f159 ]
Multiple bug reports report issues with the SOF and SST drivers when
dealing with single microphone cases.
We currently read the DMIC array information unconditionally but we
don't check that the configuration type is actually a mic array.
When the DMIC link does not rely on a mic array configuration, the
recommendation is to check the format information to infer the maximum
number of channels, and map this to the number of microphones.
This leaves a potential for a mismatch between actual microphones
available in hardware and what the ACPI table contains, but we have no
other source of information.
Note that single microphone configurations can alternatively be
handled with a 'mic array' configuration along with a 'vendor-defined'
geometry.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201251
BugLink: https://github.com/thesofproject/linux/issues/2725
Fixes: 7a33ea70e1 ('ALSA: hda: intel-nhlt: handle NHLT VENDOR_DEFINED DMIC geometry')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210302000146.1177770-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26a9630c72 ]
Currently the mask operation on variable conf is just 3 bits so
the switch statement case value of 8 is unreachable dead code.
The function daio_mgr_dao_init can be passed a 4 bit value,
function dao_rsc_init calls it with conf set to:
conf = (desc->msr & 0x7) | (desc->passthru << 3);
so clearly when desc->passthru is set to 1 then conf can be
at least 8.
Fix this by changing the mask to 0xf.
Fixes: 8cc7236148 ("ALSA: SB X-Fi driver merge")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210227001527.1077484-1-colin.king@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 21cba9c535 upstream.
Some USB audio firmware seem to report broken dB values for the volume
controls, and this screws up applications like PulseAudio who blindly
trusts the given data. For example, Edifier G2000 reports a PCM
volume from -128dB to -127dB, and this results in barely inaudible
sound.
This patch adds a sort of sanity check at parsing the dB values in
USB-audio driver and disables the dB reporting if the range looks
bogus. Here, we assume -96dB as the bottom line of the max dB.
Note that, if one can figure out that proper dB range later, it can be
patched in the mixer maps.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211929
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210227105737.3656-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11302bb69e upstream.
The Corsair Virtuoso SE RGB Wireless is a USB headset with a mic and a
sidetone feature. Assign the Corsair Virtuoso name map to the SE product
ids as well, in order to label its mixer appropriately and allow
userspace to pick the correct volume controls.
Signed-off-by: Andrea Fagiani <andfagiani@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/40bbdf55-f854-e2ee-87b4-183e6451352c@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0e185616a upstream.
The Acer SWIFT Swift SF314-54/55 laptops with ALC256 cannot detect
both the headset mic and the internal mic. Introduce new fixup
to enable the jack sense and the headset mic. However, the internal
mic actually connects to Intel SST audio. It still needs Intel SST
support to make internal mic capture work.
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Jian-Hong Pan <jhp@endlessos.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210226010440.8474-1-chris.chiu@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
