[ Upstream commit 5918036cfa ]
Adding a MODULE_ALIAS() to drivetemp will make the driver easier
for modprobe to autoprobe.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220712214624.1845158-1-linus.walleij@linaro.org
Fixes: 5b46903d8b ("hwmon: Driver for disk and solid state drives with temperature sensors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d4edccc9b ]
Taking a lock at the beginning of .remove() doesn't prevent new readers.
With the existing approach it can happen, that a read occurs just when
the lock was taken blocking the reader until the lock is released at the
end of the remove callback which then accessed *data that is already
freed then.
To actually fix this problem the hwmon core needs some adaption. Until
this is implemented take the optimistic approach of assuming that all
readers are gone after hwmon_device_unregister() and
sysfs_remove_group() as most other drivers do. (And once the core
implements that, taking the lock would deadlock.)
So drop the lock, move the reset to after device unregistration to keep
the device in a workable state until it's deregistered. Also add a error
message in case the reset fails and return 0 anyhow. (Returning an error
code, doesn't stop the platform device unregistration and only results
in a little helpful error message before the devm cleanup handlers are
called.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220725194344.150098-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 385e5f5705 ]
A user reported that the program dell-bios-fan-control
worked on his Dell XPS 13 7390 to switch off automatic
fan control.
Since it uses the same mechanism as the dell_smm_hwmon
module, add this model to the fan control whitelist.
Compile-tested only.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220612041806.11367-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0e51022a0 ]
If platform_device_add() fails, it no need to call platform_device_del(), split
platform_device_unregister() into platform_device_del/put(), so platform_device_put()
can be called separately.
Fixes: 8808a793f0 ("ibmaem: new driver for power/energy/temp meters in IBM System X hardware")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220701074153.4021556-1-yangyingliang@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1bbb280904 ]
Currently, the response to the power cap command overwrites the
first eight bytes of the poll response, since the commands use
the same buffer. This means that user's get the wrong data between
the time of sending the power cap and the next poll response update.
Fix this by specifying a different buffer for the power cap command
response.
Fixes: 5b5513b880 ("hwmon: Add On-Chip Controller (OCC) hwmon driver")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20220628203029.51747-1-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 908dbf0242 ]
Checksumming of the request and sequence numbering is now done in the
OCC interface driver in order to keep unique sequence numbers. So
remove those in the hwmon driver. Also, add the command length to the
send_cmd function pointer, since the checksum must be placed in the
last two bytes of the command. The submit interface must receive the
exact size of the command - previously it could be rounded to the
nearest 8 bytes with no consequence.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210721190231.117185-3-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1baf7a3a3 ]
Make sure that the support of PEC is determined before the read of other
registers. Otherwise the validation of PEC can trigger an error on the read
of STATUS_BYTE or STATUS_WORD registers.
The problematic scenario is the following. A device with enabled PEC
support is up and running and a kernel driver is loaded.
Then the driver is unloaded (or device unbound), the HW device
is reconfigured externally (e.g. by i2cset) to advertise itself as not
supporting PEC. Without the move of the code, at the second load of
the driver (or bind) the STATUS_BYTE or STATUS_WORD register is always
read with PEC enabled, which is likely to cause a read error resulting
with fail of a driver load (or bind).
Signed-off-by: Adam Wujek <dev_public@wujek.eu>
Link: https://lore.kernel.org/r/20220519233334.438621-1-dev_public@wujek.eu
Fixes: 75d2b2b06b ("hwmon: (pmbus) disable PEC if not enabled")
Fixes: 4e5418f787 ("hwmon: (pmbus_core) Check adapter PEC support")
[groeck: Added Fixes: tags, dropped continuation line]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4aaaaf0f27 ]
All temperature of Fintek superio hwmonitor that using 1-byte reg will use
2's complement.
In show_temp()
temp = data->temp[nr] * 1000;
When data->temp[nr] read as 255, it indicate -1C, but this code will report
255C to userspace. It'll be ok when change to:
temp = ((s8)data->temp[nr]) * 1000;
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Link: https://lore.kernel.org/r/20220418090706.6339-1-hpeter+linux_kernel@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 151d6dcbed ]
Building with SENSORS_LTQ_CPUTEMP=y with SOC_FALCON=y causes build
errors since FALCON does not support the same features as XWAY.
Change this symbol to depend on SOC_XWAY since that provides the
necessary interfaces.
Repairs these build errors:
../drivers/hwmon/ltq-cputemp.c: In function 'ltq_cputemp_enable':
../drivers/hwmon/ltq-cputemp.c:23:9: error: implicit declaration of function 'ltq_cgu_w32'; did you mean 'ltq_ebu_w32'? [-Werror=implicit-function-declaration]
23 | ltq_cgu_w32(ltq_cgu_r32(CGU_GPHY1_CR) | CGU_TEMP_PD, CGU_GPHY1_CR);
../drivers/hwmon/ltq-cputemp.c:23:21: error: implicit declaration of function 'ltq_cgu_r32'; did you mean 'ltq_ebu_r32'? [-Werror=implicit-function-declaration]
23 | ltq_cgu_w32(ltq_cgu_r32(CGU_GPHY1_CR) | CGU_TEMP_PD, CGU_GPHY1_CR);
../drivers/hwmon/ltq-cputemp.c: In function 'ltq_cputemp_probe':
../drivers/hwmon/ltq-cputemp.c:92:31: error: 'SOC_TYPE_VR9_2' undeclared (first use in this function)
92 | if (ltq_soc_type() != SOC_TYPE_VR9_2)
Fixes: 7074d0a927 ("hwmon: (ltq-cputemp) add cpu temp sensor driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Florian Eckert <fe@dev.tdt.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: linux-hwmon@vger.kernel.org
Link: https://lore.kernel.org/r/20220509234740.26841-1-rdunlap@infradead.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3481551f03 ]
This driver doesn't have of_match_table. This makes the kernel module
tmp401.ko lack alias patterns (e.g: of:N*T*Cti,tmp411) to match DT node
of the supported devices hence this kernel module will not be
automatically loaded.
After adding of_match_table to this driver, the folllowing alias will be
added into tmp401.ko.
$ modinfo drivers/hwmon/tmp401.ko
filename: drivers/hwmon/tmp401.ko
......
author: Hans de Goede <hdegoede@redhat.com>
alias: of:N*T*Cti,tmp435C*
alias: of:N*T*Cti,tmp435
alias: of:N*T*Cti,tmp432C*
alias: of:N*T*Cti,tmp432
alias: of:N*T*Cti,tmp431C*
alias: of:N*T*Cti,tmp431
alias: of:N*T*Cti,tmp411C*
alias: of:N*T*Cti,tmp411
alias: of:N*T*Cti,tmp401C*
alias: of:N*T*Cti,tmp401
......
Fixes: af503716ac ("i2c: core: report OF style module alias for devices registered via OF")
Signed-off-by: Camel Guo <camel.guo@axis.com>
Link: https://lore.kernel.org/r/20220503114333.456476-1-camel.guo@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 75d2b2b06b upstream.
Explicitly disable PEC when the client does not support it.
The problematic scenario is the following. A device with enabled PEC
support is up and running and a kernel driver is loaded.
Then the driver is unloaded (or device unbound), the HW device
is reconfigured externally (e.g. by i2cset) to advertise itself as not
supporting PEC. Without a new code, at the second load of the driver
(or bind) the "flags" variable is not updated to avoid PEC usage. As a
consequence the further communication with the device is done with
the PEC enabled, which is wrong and may fail.
The implementation first disable the I2C_CLIENT_PEC flag, then the old
code enable it if needed.
Fixes: 4e5418f787 ("hwmon: (pmbus_core) Check adapter PEC support")
Signed-off-by: Adam Wujek <dev_public@wujek.eu>
Link: https://lore.kernel.org/r/20220420145059.431061-1-dev_public@wujek.eu
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b2666ce44 upstream.
When removing the adt7470 module, a warning might be printed:
do not call blocking ops when !TASK_RUNNING; state=1
set at [<ffffffffa006052b>] adt7470_update_thread+0x7b/0x130 [adt7470]
This happens because adt7470_update_thread() can leave the kthread in
TASK_INTERRUPTIBLE state when the kthread is being stopped before
the call of set_current_state(). Since kthread_exit() might sleep in
exit_signals(), the warning is printed.
Fix that by using schedule_timeout_interruptible() and removing
the call of set_current_state().
This causes TASK_INTERRUPTIBLE to be set after kthread_should_stop()
which might cause the kthread to exit.
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Fixes: 93cacfd41f (hwmon: (adt7470) Allow faster removal)
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Tested-by: Zheyu Ma <zheyuma97@gmail.com>
Link: https://lore.kernel.org/r/20220407101312.13331-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a5436af598 ]
If there is an input undervoltage fault, reported in STATUS_INPUT
command response, there is quite likely a "Unit Off For Insufficient
Input Voltage" condition as well.
Add a constant for bit 3 of STATUS_INPUT. Update the Vin limit
attributes to include both bits in the mask for clearing faults.
If an input undervoltage fault occurs, causing a unit off for
insufficient input voltage, but the unit is off bit is not cleared, the
STATUS_WORD will not be updated to clear the input fault condition.
Including the unit is off bit (bit 3) allows for the input fault
condition to completely clear.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Link: https://lore.kernel.org/r/20220317232123.2103592-1-bjwyman@gmail.com
Fixes: b4ce237b7f ("hwmon: (pmbus) Introduce infrastructure to detect sensors and limit registers")
[groeck: Dropped unnecessary ()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 647d6f09be ]
If the watchdog was already enabled by the BIOS after booting, the
watchdog infrastructure needs to regularly send keepalives to
prevent a unexpected reset.
WDOG_ACTIVE only serves as an status indicator for userspace,
we want to use WDOG_HW_RUNNING instead.
Since my Fujitsu Esprimo P720 does not support the watchdog,
this change is compile-tested only.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Fixes: fb551405c0 (watchdog: sch56xx: Use watchdog core)
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220131211935.3656-5-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 686d303ee6 ]
On PMBUS devices with multiple pages, the regulator ops need to be
protected with the update mutex. This prevents accidentally changing
the page in a separate thread while operating on the PMBUS_OPERATION
register.
Tested on Infineon xdpe11280 while a separate thread polls for sensor
data.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Link: https://lore.kernel.org/r/b991506bcbf665f7af185945f70bf9d5cf04637c.1645804976.git.sylv@sylv.io
Fixes: ddbb4db4ce ("hwmon: (pmbus) Add regulator support")
Cc: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35f165f089 ]
Almost all fault/warning bits in pmbus status registers remain set even
after fault/warning condition are removed. As per pmbus specification
these faults must be cleared by user.
Modify hwmon behavior to clear fault/warning bit after fetching data if
fault/warning bit was set. This allows to get fresh data in next read.
Signed-off-by: Vikash Chandola <vikash.chandola@linux.intel.com>
Link: https://lore.kernel.org/r/20220222131253.2426834-1-vikash.chandola@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1b5f517cca upstream.
If an attempt is made to a sensor with a thermal zone and it fails,
the call to devm_thermal_zone_of_sensor_register() may return -ENODEV.
This may result in crashes similar to the following.
Unable to handle kernel NULL pointer dereference at virtual address 00000000000003cd
...
Internal error: Oops: 96000021 [#1] PREEMPT SMP
...
pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : mutex_lock+0x18/0x60
lr : thermal_zone_device_update+0x40/0x2e0
sp : ffff800014c4fc60
x29: ffff800014c4fc60 x28: ffff365ee3f6e000 x27: ffffdde218426790
x26: ffff365ee3f6e000 x25: 0000000000000000 x24: ffff365ee3f6e000
x23: ffffdde218426870 x22: ffff365ee3f6e000 x21: 00000000000003cd
x20: ffff365ee8bf3308 x19: ffffffffffffffed x18: 0000000000000000
x17: ffffdde21842689c x16: ffffdde1cb7a0b7c x15: 0000000000000040
x14: ffffdde21a4889a0 x13: 0000000000000228 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000
x8 : 0000000001120000 x7 : 0000000000000001 x6 : 0000000000000000
x5 : 0068000878e20f07 x4 : 0000000000000000 x3 : 00000000000003cd
x2 : ffff365ee3f6e000 x1 : 0000000000000000 x0 : 00000000000003cd
Call trace:
mutex_lock+0x18/0x60
hwmon_notify_event+0xfc/0x110
0xffffdde1cb7a0a90
0xffffdde1cb7a0b7c
irq_thread_fn+0x2c/0xa0
irq_thread+0x134/0x240
kthread+0x178/0x190
ret_from_fork+0x10/0x20
Code: d503201f d503201f d2800001 aa0103e4 (c8e47c02)
Jon Hunter reports that the exact call sequence is:
hwmon_notify_event()
--> hwmon_thermal_notify()
--> thermal_zone_device_update()
--> update_temperature()
--> mutex_lock()
The hwmon core needs to handle all errors returned from calls
to devm_thermal_zone_of_sensor_register(). If the call fails
with -ENODEV, report that the sensor was not attached to a
thermal zone but continue to register the hwmon device.
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Cc: Dmitry Osipenko <digetx@gmail.com>
Fixes: 1597b374af ("hwmon: Add notification support")
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0d79987a0 upstream.
When setting the fan speed, i8k_set_fan() calls i8k_get_fan_status(),
causing an unnecessary SMM call since from the two users of this
function, only i8k_ioctl_unlocked() needs to know the new fan status
while dell_smm_write() ignores the new fan status.
Since SMM calls can be very slow while also making error reporting
difficult for dell_smm_write(), remove the function call from
i8k_set_fan() and call it separately in i8k_ioctl_unlocked().
Tested on a Dell Inspiron 3505.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20211021190531.17379-6-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c1ec0cabc3 ]
The "val" variable is controlled by the user and comes from
hwmon_attr_store(). The FAN_RPM_TO_PERIOD() macro divides by "val"
so a zero will crash the system. Check for that and return -EINVAL.
Negatives are also invalid so return -EINVAL for those too.
Fixes: fc958a61ff ("hwmon: (adt7470) Convert to devm_hwmon_device_register_with_info API")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d379880d9a ]
sysfs and udev notifications need to be sent to the _alarm
attributes, not to the value attributes.
Fixes: 94dbd23ed8 ("hwmon: (lm90) Use hwmon_notify_event()")
Cc: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a53fff96f3 ]
Experiments with MAX6654 show that its alert function is broken,
similar to other chips supported by the lm90 driver. Mark it accordingly.
Fixes: 229d495d81 ("hwmon: (lm90) Add max6654 support to lm90 driver")
Cc: Josh Lehan <krellan@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc341a1a98 ]
If alert handling is broken, interrupts are disabled after an alert and
re-enabled after the alert clears. However, if there is an interrupt
handler, this does not apply if alerts were originally disabled and enabled
when the driver was loaded. In that case, interrupts will stay disabled
after an alert was handled though the alert handler even after the alert
condition clears. Address the situation by always re-enabling interrupts
after the alert condition clears if there is an interrupt handler.
Fixes: 2abdc357c5 ("hwmon: (lm90) Unmask hardware interrupt")
Cc: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a66c5ed539 ]
According to its datasheet, G781 supports a maximum conversion rate value
of 8 (62.5 ms). However, chips labeled G781 and G780 were found to only
support a maximum conversion rate value of 7 (125 ms). On the other side,
chips labeled G781-1 and G784 were found to support a conversion rate value
of 8. There is no known means to distinguish G780 from G781 or G784; all
chips report the same manufacturer ID and chip revision.
Setting the conversion rate register value to 8 on chips not supporting
it causes unexpected behavior since the real conversion rate is set to 0
(16 seconds) if a value of 8 is written into the conversion rate register.
Limit the conversion rate register value to 7 for all G78x chips to avoid
the problem.
Fixes: ae544f64cc ("hwmon: (lm90) Add support for GMT G781")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 94746b0ba4 upstream.
Experiments with MAX6680 and MAX6681 show that the alert function of those
chips is broken, similar to other chips supported by the lm90 driver.
Mark it accordingly.
Fixes: 4667bcb8d8 ("hwmon: (lm90) Introduce chip parameter structure")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f614629f9c upstream.
Experiments with MAX6646 and MAX6648 show that the alert function of those
chips is broken, similar to other chips supported by the lm90 driver.
Mark it accordingly.
Fixes: 4667bcb8d8 ("hwmon: (lm90) Introduce chip parameter structure")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a8d6d4992a ]
In the file mr75203.c we have a macro named POWER_DELAY_CYCLE_256,
the correct value should be 0x100. The register ip_tmr is expressed
in units of IP clk cycles, in accordance with the datasheet.
Typical power-up delays for Temperature Sensor are 256 cycles i.e. 0x100.
Fixes: 9d823351a3 ("hwmon: Add hardware monitoring driver for Moortec MR75203 PVT controller")
Signed-off-by: Arseny Demidov <a.demidov@yadro.com>
Link: https://lore.kernel.org/r/20211219102239.1112-1-a.demidov@yadro.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cdc5287aca upstream.
Bit 7 of the status register indicates that the chip is busy
doing a conversion. It does not indicate an alarm status.
Stop reporting it as alarm status bit.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da7dc05684 upstream.
Tests with a real chip and a closer look into the datasheet reveals
that the local and remote critical alarm status bits are swapped for
MAX6680/MAX6681.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 16ba51b5dc ]
Tests with a real chip and a closer look into the datasheet show that
MAX6654 does not support CRIT/THERM/OVERTEMP limits, so drop support
of the respective attributes for this chip.
Introduce LM90_HAVE_CRIT flag and use it to instantiate critical limit
attributes to solve the problem.
Cc: Josh Lehan <krellan@google.com>
Fixes: 229d495d81 ("hwmon: (lm90) Add max6654 support to lm90 driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8344f7693 ]
TMP461 is almost identical to TMP451 and was actually detected as TMP451
with the existing lm90 driver if its I2C address is 0x4c. Add support
for it to the lm90 driver. At the same time, improve the chip detection
function to at least try to distinguish between TMP451 and TMP461.
As a side effect, this fixes commit 24333ac26d ("hwmon: (tmp401) use
smb word operations instead of 2 smb byte operations"). TMP461 does not
support word operations on temperature registers, which causes bad
temperature readings with the tmp401 driver. The lm90 driver does not
perform word operations on temperature registers and thus does not have
this problem.
Support is listed as basic because TMP461 supports a sensor resolution
of 0.0625 degrees C, while the lm90 driver assumes a resolution of 0.125
degrees C. Also, the TMP461 supports negative temperatures with its
default temperature range, which is not the case for similar chips
supported by the lm90 and the tmp401 drivers. Those limitations will be
addressed with follow-up patches.
Fixes: 24333ac26d ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations")
Reported-by: David T. Wilson <david.wilson@nasa.gov>
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f347e249fc ]
A flag indicating extended temperature support makes it easier
to add support for additional chips with this functionality.
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55840b9eae ]
Commit b50aa49638 ("hwmon: (lm90) Prevent integer underflows of
temperature calculations") addressed a number of underflow situations
when writing temperature limits. However, it missed one situation, seen
when an attempt is made to set the hysteresis value to MAX_LONG and the
critical temperature limit is negative.
Use clamp_val() when setting the hysteresis temperature to ensure that
the provided value can never overflow or underflow.
Fixes: b50aa49638 ("hwmon: (lm90) Prevent integer underflows of temperature calculations")
Cc: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fce15c45d3 ]
The detect function had a comment "Make compiler happy" when id did not
read the second configuration register. As it turns out, the code was
checking the contents of this register for manufacturer ID 0xA1 (NXP
Semiconductor/Philips), but never actually read the register. So it
wasn't surprising that the compiler complained, and it indeed had a point.
Fix the code to read the register contents for manufacturer ID 0xa1.
At the same time, the code was reading the register for manufacturer ID
0x41 (Analog Devices), but it was not using the results. In effect it was
just checking if reading the register returned an error. That doesn't
really add much if any value, so stop doing that.
Fixes: f90be42fb3 ("hwmon: (lm90) Refactor reading of config2 register")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit dbd3e6eaf3 upstream.
The removal function is called regardless of whether
/proc/i8k was created successfully or not, the later
causing a WARN() on module removal.
Fix that by only registering the removal function
if /proc/i8k was created successfully.
Tested on a Inspiron 3505.
Fixes: 039ae58503 ("hwmon: Allow to compile dell-smm-hwmon driver without /proc/i8k")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20211112171440.59006-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2ca752055 upstream.
Before commit 86585c6197 ("hwmon: (pwm-fan) stop using legacy
PWM functions and some cleanups") pwm_apply_state() was called
unconditionally in pwm_fan_probe(). In this commit this direct
call was replaced by a call to __set_pwm(ct, MAX_PWM) which
however is a noop if ctx->pwm_value already matches the value to
set.
After probe the fan is supposed to run at full speed, and the
internal driver state suggests it does, but this isn't asserted
and depending on bootloader and pwm low-level driver, the fan
might just be off.
So drop setting pwm_value to MAX_PWM to ensure the check in
__set_pwm doesn't make it exit early and the fan goes on as
intended.
Cc: stable@vger.kernel.org
Fixes: 86585c6197 ("hwmon: (pwm-fan) stop using legacy PWM functions and some cleanups")
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211130092212.17783-1-billy_tsai@aspeedtech.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b7931a7b0e ]
Maintaining this manually is error prone (there are currently only
five chips supported, not six); gcc can do it for us automatically.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 666c14906b ("hwmon: (pmbus/lm25066) Drop support for LM25063")
Link: https://lore.kernel.org/r/20210928092242.30036-5-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ada61aa0b1 ]
I got memory leak as follows when doing fault injection test:
unreferenced object 0xffff888102740438 (size 8):
comm "27", pid 859, jiffies 4295031351 (age 143.992s)
hex dump (first 8 bytes):
68 77 6d 6f 6e 30 00 00 hwmon0..
backtrace:
[<00000000544b5996>] __kmalloc_track_caller+0x1a6/0x300
[<00000000df0d62b9>] kvasprintf+0xad/0x140
[<00000000d3d2a3da>] kvasprintf_const+0x62/0x190
[<000000005f8f0f29>] kobject_set_name_vargs+0x56/0x140
[<00000000b739e4b9>] dev_set_name+0xb0/0xe0
[<0000000095b69c25>] __hwmon_device_register+0xf19/0x1e50 [hwmon]
[<00000000a7e65b52>] hwmon_device_register_with_info+0xcb/0x110 [hwmon]
[<000000006f181e86>] devm_hwmon_device_register_with_info+0x85/0x100 [hwmon]
[<0000000081bdc567>] tmp421_probe+0x2d2/0x465 [tmp421]
[<00000000502cc3f8>] i2c_device_probe+0x4e1/0xbb0
[<00000000f90bda3b>] really_probe+0x285/0xc30
[<000000007eac7b77>] __driver_probe_device+0x35f/0x4f0
[<000000004953d43d>] driver_probe_device+0x4f/0x140
[<000000002ada2d41>] __device_attach_driver+0x24c/0x330
[<00000000b3977977>] bus_for_each_drv+0x15d/0x1e0
[<000000005bf2a8e3>] __device_attach+0x267/0x410
When device_register() returns an error, the name allocated in
dev_set_name() will be leaked, the put_device() should be used
instead of calling hwmon_dev_release() to give up the device
reference, then the name will be freed in kobject_cleanup().
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: bab2243ce1 ("hwmon: Introduce hwmon_device_register_with_groups")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211012112758.2681084-1-yangyingliang@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ae59dc455a upstream.
With the exception of the lm5066i, all the devices handled by this
driver had been missing their offset ('b') coefficients for direct
format readings.
Cc: stable@vger.kernel.org
Fixes: 58615a94f6 ("hwmon: (pmbus/lm25066) Add support for LM25056")
Fixes: e53e6497fc ("hwmon: (pmbus/lm25066) Refactor device specific coefficients")
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20210928092242.30036-2-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If driver read tmp value sufficient for
(tmp & 0x08) && (!(tmp & 0x80)) && ((tmp & 0x7) == ((tmp >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().
The patch fixes possible NULL pointer dereference by removing lm75[].
Found by Linux Driver Verification project (linuxtesting.org).
Cc: stable@vger.kernel.org
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210921155153.28098-3-lutovinova@ispras.ru
[groeck: Dropped unnecessary continuation lines, fixed multi-line alignments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If driver read val value sufficient for
(val & 0x08) && (!(val & 0x80)) && ((val & 0x7) == ((val >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().
The patch fixes possible NULL pointer dereference by removing lm75[].
Found by Linux Driver Verification project (linuxtesting.org).
Cc: stable@vger.kernel.org
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210921155153.28098-2-lutovinova@ispras.ru
[groeck: Dropped unnecessary continuation lines, fixed multipline alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If driver read val value sufficient for
(val & 0x08) && (!(val & 0x80)) && ((val & 0x7) == ((val >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().
The patch fixes possible NULL pointer dereference by removing lm75[].
Found by Linux Driver Verification project (linuxtesting.org).
Cc: stable@vger.kernel.org
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210921155153.28098-1-lutovinova@ispras.ru
[groeck: Dropped unnecessary continuation lines, fixed multi-line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add missed attribute for reading POUT from page 1.
It is supported by device, but has been missed in initial commit.
Fixes: 2c6fcbb211 ("hwmon: (pmbus) Add support for MPS Multi-phase mp2975 controller")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210927070740.2149290-1-vadimp@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The bytes for max_power_out from the ibm-cffps devices differ in byte
order for some power supplies.
The Witherspoon power supply returns the bytes in MSB/LSB order.
The Rainier power supply returns the bytes in LSB/MSB order.
The Witherspoon power supply uses version cffps1. The Rainier power
supply should use version cffps2. If version is cffps1, swap the bytes
before output to max_power_out.
Tested:
Witherspoon before: 3148. Witherspoon after: 3148.
Rainier before: 53255. Rainier after: 2000.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210928205051.1222815-1-bjwyman@gmail.com
[groeck: Replaced yoda programming]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The P10 (temp sensor version 0x10) doesn't do the same VRM status
reporting that was used on P9. It just reports the temperature, so
drop the check for VRM fru type in the sysfs show function, and don't
set the name to "alarm".
Fixes: db4919ec86 ("hwmon: (occ) Add new temperature sensor type")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210929153604.14968-1-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The return value of devm_clk_get should in general be propagated to
upper layer. In this case the clk is optional, use the appropriate
wrapper instead of interpreting all errors as "The optional clk is not
available".
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210923201113.398932-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Old code produces -24999 for 0b1110011100000000 input in standard format due to
always rounding up rather than "away from zero".
Use the common macro for division, unify and simplify the conversion code along
the way.
Fixes: 9410700b88 ("hwmon: Add driver for Texas Instruments TMP421/422/423 sensor chips")
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Link: https://lore.kernel.org/r/20210924093011.26083-3-fercerpav@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For both local and remote sensors all the supported ICs can report an
"undervoltage lockout" condition which means the conversion wasn't
properly performed due to insufficient power supply voltage and so the
measurement results can't be trusted.
Fixes: 9410700b88 ("hwmon: Add driver for Texas Instruments TMP421/422/423 sensor chips")
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Link: https://lore.kernel.org/r/20210924093011.26083-2-fercerpav@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Function i2c_smbus_read_byte_data() can return a negative error number
instead of the data read if I2C transaction failed for whatever reason.
Lack of error checking can lead to serious issues on production
hardware, e.g. errors treated as temperatures produce spurious critical
temperature-crossed-threshold errors in BMC logs for OCP server
hardware. The patch was tested with Mellanox OCP Mezzanine card
emulating TMP421 protocol for temperature sensing which sometimes leads
to I2C protocol error during early boot up stage.
Fixes: 9410700b88 ("hwmon: Add driver for Texas Instruments TMP421/422/423 sensor chips")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Link: https://lore.kernel.org/r/20210924093011.26083-1-fercerpav@gmail.com
[groeck: dropped unnecessary line breaks]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fan speed minimum can be enforced from sysfs. For example, setting
current fan speed to 20 is used to enforce fan speed to be at 100%
speed, 19 - to be not below 90% speed, etcetera. This feature provides
ability to limit fan speed according to some system wise
considerations, like absence of some replaceable units or high system
ambient temperature.
Request for changing fan minimum speed is configuration request and can
be set only through 'sysfs' write procedure. In this situation value of
argument 'state' is above nominal fan speed maximum.
Return non-zero code in this case to avoid
thermal_cooling_device_stats_update() call, because in this case
statistics update violates thermal statistics table range.
The issues is observed in case kernel is configured with option
CONFIG_THERMAL_STATISTICS.
Here is the trace from KASAN:
[ 159.506659] BUG: KASAN: slab-out-of-bounds in thermal_cooling_device_stats_update+0x7d/0xb0
[ 159.516016] Read of size 4 at addr ffff888116163840 by task hw-management.s/7444
[ 159.545625] Call Trace:
[ 159.548366] dump_stack+0x92/0xc1
[ 159.552084] ? thermal_cooling_device_stats_update+0x7d/0xb0
[ 159.635869] thermal_zone_device_update+0x345/0x780
[ 159.688711] thermal_zone_device_set_mode+0x7d/0xc0
[ 159.694174] mlxsw_thermal_modules_init+0x48f/0x590 [mlxsw_core]
[ 159.700972] ? mlxsw_thermal_set_cur_state+0x5a0/0x5a0 [mlxsw_core]
[ 159.731827] mlxsw_thermal_init+0x763/0x880 [mlxsw_core]
[ 160.070233] RIP: 0033:0x7fd995909970
[ 160.074239] Code: 73 01 c3 48 8b 0d 28 d5 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 99 2d 2c 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d 01 f0 ff ..
[ 160.095242] RSP: 002b:00007fff54f5d938 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 160.103722] RAX: ffffffffffffffda RBX: 0000000000000013 RCX: 00007fd995909970
[ 160.111710] RDX: 0000000000000013 RSI: 0000000001906008 RDI: 0000000000000001
[ 160.119699] RBP: 0000000001906008 R08: 00007fd995bc9760 R09: 00007fd996210700
[ 160.127687] R10: 0000000000000073 R11: 0000000000000246 R12: 0000000000000013
[ 160.135673] R13: 0000000000000001 R14: 00007fd995bc8600 R15: 0000000000000013
[ 160.143671]
[ 160.145338] Allocated by task 2924:
[ 160.149242] kasan_save_stack+0x19/0x40
[ 160.153541] __kasan_kmalloc+0x7f/0xa0
[ 160.157743] __kmalloc+0x1a2/0x2b0
[ 160.161552] thermal_cooling_device_setup_sysfs+0xf9/0x1a0
[ 160.167687] __thermal_cooling_device_register+0x1b5/0x500
[ 160.173833] devm_thermal_of_cooling_device_register+0x60/0xa0
[ 160.180356] mlxreg_fan_probe+0x474/0x5e0 [mlxreg_fan]
[ 160.248140]
[ 160.249807] The buggy address belongs to the object at ffff888116163400
[ 160.249807] which belongs to the cache kmalloc-1k of size 1024
[ 160.263814] The buggy address is located 64 bytes to the right of
[ 160.263814] 1024-byte region [ffff888116163400, ffff888116163800)
[ 160.277536] The buggy address belongs to the page:
[ 160.282898] page:0000000012275840 refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff888116167000 pfn:0x116160
[ 160.294872] head:0000000012275840 order:3 compound_mapcount:0 compound_pincount:0
[ 160.303251] flags: 0x200000000010200(slab|head|node=0|zone=2)
[ 160.309694] raw: 0200000000010200 ffffea00046f7208 ffffea0004928208 ffff88810004dbc0
[ 160.318367] raw: ffff888116167000 00000000000a0006 00000001ffffffff 0000000000000000
[ 160.327033] page dumped because: kasan: bad access detected
[ 160.333270]
[ 160.334937] Memory state around the buggy address:
[ 160.356469] >ffff888116163800: fc ..
Fixes: 65afb4c8e7 ("hwmon: (mlxreg-fan) Add support for Mellanox FAN driver")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210916183151.869427-1-vadimp@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
