At the moment the GIC IRQ domain translation routine happily converts
ACPI table GSI numbers below 16 to GIC SGIs (Software Generated
Interrupts aka IPIs). On the Devicetree side we explicitly forbid this
translation, actually the function will never return HWIRQs below 16 when
using a DT based domain translation.
We expect SGIs to be handled in the first part of the function, and any
further occurrence should be treated as a firmware bug, so add a check
and print to report this explicitly and avoid lengthy debug sessions.
Fixes: 64b499d8df ("irqchip/gic-v3: Configure SGIs as standard interrupts")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220404110842.2882446-1-andre.przywara@arm.com
It turns out that our polling of RWP is totally wrong when checking
for it in the redistributors, as we test the *distributor* bit index,
whereas it is a different bit number in the RDs... Oopsie boo.
This is embarassing. Not only because it is wrong, but also because
it took *8 years* to notice the blunder...
Just fix the damn thing.
Fixes: 021f653791 ("irqchip: gic-v3: Initial support for GICv3")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20220315165034.794482-2-maz@kernel.org
The way KVM drives GICv4.{0,1} is as follows:
- vcpu_load() makes the VPE resident, instructing the RD to start
scanning for interrupts
- just before entering the guest, we check that the RD has finished
scanning and that we can start running the vcpu
- on preemption, we deschedule the VPE by making it invalid on
the RD
However, we are preemptible between the first two steps. If it so
happens *and* that the RD was still scanning, we nonetheless write
to the GICR_VPENDBASER register while Dirty is set, and bad things
happen (we're in UNPRED land).
This affects both the 4.0 and 4.1 implementations.
Make sure Dirty is cleared before performing the deschedule,
meaning that its_clear_vpend_valid() becomes a sort of full VPE
residency barrier.
Reported-by: Jingyi Wang <wangjingyi11@huawei.com>
Tested-by: Nianyao Tang <tangnianyao@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Fixes: 57e3cebd02 ("KVM: arm64: Delay the polling of the GICR_VPENDBASER.Dirty bit")
Link: https://lore.kernel.org/r/4aae10ba-b39a-5f84-754b-69c2eb0a2c03@huawei.com
If MAILBOX is n, building fails:
drivers/irqchip/irq-qcom-mpm.o: In function `mpm_pd_power_off':
irq-qcom-mpm.c:(.text+0x174): undefined reference to `mbox_send_message'
irq-qcom-mpm.c:(.text+0x174): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `mbox_send_message'
Make QCOM_MPM depends on MAILBOX to fix this.
Fixes: a6199bb514 ("irqchip: Add Qualcomm MPM controller driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220317131956.30004-1-yuehaibing@huawei.com
There are three sets of updates for 5.18 in the asm-generic tree:
- The set_fs()/get_fs() infrastructure gets removed for good. This
was already gone from all major architectures, but now we can
finally remove it everywhere, which loses some particularly
tricky and error-prone code.
There is a small merge conflict against a parisc cleanup, the
solution is to use their new version.
- The nds32 architecture ends its tenure in the Linux kernel. The
hardware is still used and the code is in reasonable shape, but
the mainline port is not actively maintained any more, as all
remaining users are thought to run vendor kernels that would never
be updated to a future release.
There are some obvious conflicts against changes to the removed
files.
- A series from Masahiro Yamada cleans up some of the uapi header
files to pass the compile-time checks.
-----BEGIN PGP SIGNATURE-----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=vtCN
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are three sets of updates for 5.18 in the asm-generic tree:
- The set_fs()/get_fs() infrastructure gets removed for good.
This was already gone from all major architectures, but now we can
finally remove it everywhere, which loses some particularly tricky
and error-prone code. There is a small merge conflict against a
parisc cleanup, the solution is to use their new version.
- The nds32 architecture ends its tenure in the Linux kernel.
The hardware is still used and the code is in reasonable shape, but
the mainline port is not actively maintained any more, as all
remaining users are thought to run vendor kernels that would never
be updated to a future release.
- A series from Masahiro Yamada cleans up some of the uapi header
files to pass the compile-time checks"
* tag 'asm-generic-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (27 commits)
nds32: Remove the architecture
uaccess: remove CONFIG_SET_FS
ia64: remove CONFIG_SET_FS support
sh: remove CONFIG_SET_FS support
sparc64: remove CONFIG_SET_FS support
lib/test_lockup: fix kernel pointer check for separate address spaces
uaccess: generalize access_ok()
uaccess: fix type mismatch warnings from access_ok()
arm64: simplify access_ok()
m68k: fix access_ok for coldfire
MIPS: use simpler access_ok()
MIPS: Handle address errors for accesses above CPU max virtual user address
uaccess: add generic __{get,put}_kernel_nofault
nios2: drop access_ok() check from __put_user()
x86: use more conventional access_ok() definition
x86: remove __range_not_ok()
sparc64: add __{get,put}_kernel_nofault()
nds32: fix access_ok() checks in get/put_user
uaccess: fix nios2 and microblaze get_user_8()
sparc64: fix building assembly files
...
Updates for IRQ stacks and virtually mapped stack support for ARM from
the following pull requests, etc:
1) ARM: support for IRQ and vmap'ed stacks
This PR covers all the work related to implementing IRQ stacks and
vmap'ed stacks for all 32-bit ARM systems that are currently supported
by the Linux kernel, including RiscPC and Footbridge. It has been
submitted for review in three different waves:
- IRQ stacks support for v7 SMP systems [0],
- vmap'ed stacks support for v7 SMP systems[1],
- extending support for both IRQ stacks and vmap'ed stacks for all
remaining configurations, including v6/v7 SMP multiplatform kernels
and uniprocessor configurations including v7-M [2]
[0] https://lore.kernel.org/linux-arm-kernel/20211115084732.3704393-1-ardb@kernel.org/
[1] https://lore.kernel.org/linux-arm-kernel/20211122092816.2865873-1-ardb@kernel.org/
[2] https://lore.kernel.org/linux-arm-kernel/20211206164659.1495084-1-ardb@kernel.org/
2) ARM: support for IRQ and vmap'ed stacks [v6]
This tag covers the changes between the version of vmap'ed + IRQ stacks
support pulled into rmk/devel-stable [0] (which was dropped from v5.17
due to issues discovered too late in the cycle), and my v5 proposed for
the v5.18 cycle [1].
[0] git://git.kernel.org/pub/scm/linux/kernel/git/ardb/linux.git arm-irq-and-vmap-stacks-for-rmk
[1] https://lore.kernel.org/linux-arm-kernel/20220124174744.1054712-1-ardb@kernel.org/
3) ARM: ftrace fixes and cleanups
Make all flavors of ftrace available on all builds, regardless of ISA
choice, unwinder choice or compiler:
- use ADD not POP where possible
- fix a couple of Thumb2 related issues
- enable HAVE_FUNCTION_GRAPH_FP_TEST for robustness
- enable the graph tracer with the EABI unwinder
- avoid clobbering frame pointer registers to make Clang happy
Link: https://lore.kernel.org/linux-arm-kernel/20220203082204.1176734-1-ardb@kernel.org/
4) Fixes for the above.
-----BEGIN PGP SIGNATURE-----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=AVCL
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
"Updates for IRQ stacks and virtually mapped stack support, and ftrace:
- Support for IRQ and vmap'ed stacks
This covers all the work related to implementing IRQ stacks and
vmap'ed stacks for all 32-bit ARM systems that are currently
supported by the Linux kernel, including RiscPC and Footbridge. It
has been submitted for review in four different waves:
- IRQ stacks support for v7 SMP systems [0]
- vmap'ed stacks support for v7 SMP systems[1]
- extending support for both IRQ stacks and vmap'ed stacks for all
remaining configurations, including v6/v7 SMP multiplatform
kernels and uniprocessor configurations including v7-M [2]
- fixes and updates in [3]
- ftrace fixes and cleanups
Make all flavors of ftrace available on all builds, regardless of
ISA choice, unwinder choice or compiler [4]:
- use ADD not POP where possible
- fix a couple of Thumb2 related issues
- enable HAVE_FUNCTION_GRAPH_FP_TEST for robustness
- enable the graph tracer with the EABI unwinder
- avoid clobbering frame pointer registers to make Clang happy
- Fixes for the above"
[0] https://lore.kernel.org/linux-arm-kernel/20211115084732.3704393-1-ardb@kernel.org/
[1] https://lore.kernel.org/linux-arm-kernel/20211122092816.2865873-1-ardb@kernel.org/
[2] https://lore.kernel.org/linux-arm-kernel/20211206164659.1495084-1-ardb@kernel.org/
[3] https://lore.kernel.org/linux-arm-kernel/20220124174744.1054712-1-ardb@kernel.org/
[4] https://lore.kernel.org/linux-arm-kernel/20220203082204.1176734-1-ardb@kernel.org/
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (62 commits)
ARM: fix building NOMMU ARMv4/v5 kernels
ARM: unwind: only permit stack switch when unwinding call_with_stack()
ARM: Revert "unwind: dump exception stack from calling frame"
ARM: entry: fix unwinder problems caused by IRQ stacks
ARM: unwind: set frame.pc correctly for current-thread unwinding
ARM: 9184/1: return_address: disable again for CONFIG_ARM_UNWIND=y
ARM: 9183/1: unwind: avoid spurious warnings on bogus code addresses
Revert "ARM: 9144/1: forbid ftrace with clang and thumb2_kernel"
ARM: mach-bcm: disable ftrace in SMC invocation routines
ARM: cacheflush: avoid clobbering the frame pointer
ARM: kprobes: treat R7 as the frame pointer register in Thumb2 builds
ARM: ftrace: enable the graph tracer with the EABI unwinder
ARM: unwind: track location of LR value in stack frame
ARM: ftrace: enable HAVE_FUNCTION_GRAPH_FP_TEST
ARM: ftrace: avoid unnecessary literal loads
ARM: ftrace: avoid redundant loads or clobbering IP
ARM: ftrace: use trampolines to keep .init.text in branching range
ARM: ftrace: use ADD not POP to counter PUSH at entry
ARM: ftrace: ensure that ADR takes the Thumb bit into account
ARM: make get_current() and __my_cpu_offset() __always_inline
...
- Add support for the STM32MP13 variant
- Move parent device away from struct irq_chip
- Remove all instances of non-const strings assigned to
struct irq_chip::name, enabling a nice cleanup for VIC and GIC)
- Simplify the Qualcomm PDC driver
- A bunch of SiFive PLIC cleanups
- Add support for a new variant of the Meson GPIO block
- Add support for the irqchip side of the Apple M1 PMU
- Add support for the Apple M1 Pro/Max AICv2 irqchip
- Add support for the Qualcomm MPM wakeup gadget
- Move the Xilinx driver over to the generic irqdomain handling
- Tiny speedup for IPIs on GICv3 systems
- The usual odd cleanups
-----BEGIN PGP SIGNATURE-----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=cf1B
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- Add support for the STM32MP13 variant
- Move parent device away from struct irq_chip
- Remove all instances of non-const strings assigned to
struct irq_chip::name, enabling a nice cleanup for VIC and GIC)
- Simplify the Qualcomm PDC driver
- A bunch of SiFive PLIC cleanups
- Add support for a new variant of the Meson GPIO block
- Add support for the irqchip side of the Apple M1 PMU
- Add support for the Apple M1 Pro/Max AICv2 irqchip
- Add support for the Qualcomm MPM wakeup gadget
- Move the Xilinx driver over to the generic irqdomain handling
- Tiny speedup for IPIs on GICv3 systems
- The usual odd cleanups
Link: https://lore.kernel.org/all/20220313105142.704579-1-maz@kernel.org
The removal of the old-style irq entry broke obscure NOMMU
configurations on machines that have an MMU:
ld.lld: error: undefined symbol: generic_handle_arch_irq
referenced by kernel/entry-armv.o:(__irq_svc) in archive arch/arm/built-in.a
A follow-up patch to convert nvic to the generic_handle_arch_irq()
could have fixed this by removing the Kconfig conditional, but did
it differently.
Change the Kconfig logic so ARM machines now unconditionally
enable the feature.
I have also submitted a patch to remove support for the configurations
that broke, but fixing the regression first is a trivial and correct
change.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 54f481a230 ("ARM: remove old-style irq entry")
Fixes: 52d2408717 ("irqchip: nvic: Use GENERIC_IRQ_MULTI_HANDLER")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Qualcomm SoCs based on the RPM architecture have a MSM Power Manager (MPM)
in always-on domain. In addition to managing resources during sleep, the
hardware also has an interrupt controller that monitors the interrupts
when the system is asleep, wakes up the APSS when one of these interrupts
occur and replays it to GIC after it becomes operational.
It adds an irqchip driver for this interrupt controller, and here are
some notes about it.
- For given SoC, a fixed number of MPM pins are supported, e.g. 96 pins
on QCM2290. Each of these MPM pins can be either a MPM_GIC pin or
a MPM_GPIO pin. The mapping between MPM_GIC pin and GIC interrupt
is defined by SoC, as well as the mapping between MPM_GPIO pin and
GPIO number. The former mapping is retrieved from device tree, while
the latter is defined in TLMM pinctrl driver.
- The power domain (PD) .power_off hook is used to notify RPM that APSS
is about to power collapse. This requires MPM PD be the parent PD of
CPU cluster.
- When SoC gets awake from sleep mode, the driver will receive an
interrupt from RPM, so that it can replay interrupt for particular
polarity.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220308080534.3384532-3-shawn.guo@linaro.org
* irq/aic-v2:
: .
: Add support for the interrupt controller found is the latest
: incarnation of Apple M1 systems, courtesy of Hector Martin.
: .
irqchip/apple-aic: Add support for AICv2
irqchip/apple-aic: Support multiple dies
irqchip/apple-aic: Dynamically compute register offsets
irqchip/apple-aic: Switch to irq_domain_create_tree and sparse hwirqs
irqchip/apple-aic: Add Fast IPI support
dt-bindings: interrupt-controller: apple,aic2: New binding for AICv2
PCI: apple: Change MSI handling to handle 4-cell AIC fwspec form
Signed-off-by: Marc Zyngier <maz@kernel.org>
Introduce support for the new AICv2 hardware block in t6000/t6001 SoCs.
It seems these blocks are missing the information required to compute
the event register offset in the capability registers, so we specify
that in the DT as a second reg entry.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220309192123.152028-8-marcan@marcan.st
Multi-die support in AICv2 uses several sets of IRQ registers. Introduce
a die count and compute the register group offset based on the die ID
field of the hwirq number, as reported by the hardware.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220309192123.152028-7-marcan@marcan.st
This allows us to support AIC variants with different numbers of IRQs
based on capability registers.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220309192123.152028-6-marcan@marcan.st
This allows us to directly use the hardware event number as the hwirq
number. Since IRQ events have bit 16 set (type=1), FIQs now move to
starting at hwirq number 0.
This will become more important once multi-die support is introduced in
a later commit.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220309192123.152028-5-marcan@marcan.st
The newer AICv2 present in t600x SoCs does not have legacy IPI support
at all. Since t8103 also supports Fast IPIs, implement support for this
first. The legacy IPI code is left as a fallback, so it can be
potentially used by older SoCs in the future.
The vIPI code is shared; only the IPI firing/acking bits change for Fast
IPIs.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220309192123.152028-4-marcan@marcan.st
An emparassing typo: allocating a pointer instead of the object
pointed to. No harm done, as the pointer is large enough for
what we are using the object for, but still...
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220310050238.4478-1-guozhengkui@vivo.com
* irq/meson-gpio:
: .
: Expand meson-gpio support to deal with the new Meson-S4 SoC
: .
irqchip/meson-gpio: Add support for meson s4 SoCs
irqchip/meson-gpio: add select trigger type callback
irqchip/meson-gpio: support more than 8 channels gpio irq
dt-bindings: interrupt-controller: New binding for Meson-S4 SoCs
Signed-off-by: Marc Zyngier <maz@kernel.org>
The meson s4 SoCs support 12 gpio irq lines compared with previous
serial chips and have something different, details are as below.
IRQ Number:
- 80:68 13 pins on bank Z
- 67:48 20 pins on bank X
- 47:36 12 pins on bank H
- 35:24 12 pins on bank D
- 23:22 2 pins on bank E
- 21:14 8 pins on bank C
- 13:0 13 pins on bank B
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
[maz: fixed some W=1 build warnings]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220225055207.1048-5-qianggui.song@amlogic.com
The nds32 architecture, also known as AndeStar V3, is a custom 32-bit
RISC target designed by Andes Technologies. Support was added to the
kernel in 2016 as the replacement RISC-V based V5 processors were
already announced, and maintained by (current or former) Andes
employees.
As explained by Alan Kao, new customers are now all using RISC-V,
and all known nds32 users are already on longterm stable kernels
provided by Andes, with no development work going into mainline
support any more.
While the port is still in a reasonably good shape, it only gets
worse over time without active maintainers, so it seems best
to remove it before it becomes unusable. As always, if it turns
out that there are mainline users after all, and they volunteer
to maintain the port in the future, the removal can be reverted.
Link: https://lore.kernel.org/linux-mm/YhdWNLUhk+x9RAzU@yamatobi.andestech.com/
Link: https://lore.kernel.org/lkml/20220302065213.82702-1-alankao@andestech.com/
Link: https://www.andestech.com/en/products-solutions/andestar-architecture/
Signed-off-by: Alan Kao <alankao@andestech.com>
[arnd: rewrite changelog to provide more background]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Due to some chips may use different registers and offset, provide
a set trigger type call back and add one for old controller.
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220225055207.1048-4-qianggui.song@amlogic.com
Current meson gpio irqchip driver only support 8 channels for gpio irq
line, later chips may have more then 8 channels, so need to modify code
to support more.
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220225055207.1048-3-qianggui.song@amlogic.com
* irq/misc-5.18:
: .
: Misc irq chip changes for 5.18
:
: - GICv3: Relax ordering of previous stores to only include the ISH domain
:
: - nvic: Unmap MMIo region on probe failure
:
: - xilinx: Switch to GENERIC_IRQ_MULTI_HANDLER when used on microblaze
: .
irqchip/xilinx: Switch to GENERIC_IRQ_MULTI_HANDLER
irqchip/nvic: Release nvic_base upon failure
irqchip/gic-v3: Use dsb(ishst) to order writes with ICC_SGI1R_EL1 accesses
Signed-off-by: Marc Zyngier <maz@kernel.org>
* irq/plic-cleanups:
: .
: SiFive PLIC cleanups from Niklas Cassel:
:
: - Clarify some of the namings in the driver
:
: - Make sure S-mode interrupts are disabled when running in M-mode
: .
irqchip/sifive-plic: Disable S-mode IRQs if running in M-mode
irqchip/sifive-plic: Improve naming scheme for per context offsets
Signed-off-by: Marc Zyngier <maz@kernel.org>
Register the Xilinx driver as the root interrupt controller using
the GENERIC_IRQ_MULTI_HANDLER API, instead of the arch-specific hack.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stefan Asserhall <stefan.asserhall@xilinx.com>
[maz: repainted commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/e6c6595a81f662bf839cee3109d0fa58a596ea47.1646380284.git.michal.simek@xilinx.com
When detecting a context for a privilege mode different from the current
running privilege mode, we simply skip to the next context register.
This means that we never clear the S-mode enable bits when running in
M-mode.
On canaan k210, a bunch of S-mode interrupts are enabled by the bootrom.
These S-mode specific interrupts should never trigger, since we never set
the mie.SEIE bit in the parent interrupt controller (riscv-intc).
However, we will be able to see the mip.SEIE bit set as pending.
This isn't a good default when CONFIG_RISCV_M_MODE is set, since in that
case we will never enter a lower privilege mode (e.g. S-mode).
Let's clear the S-mode enable bits when running the kernel in M-mode, such
that we won't have a interrupt pending bit set, which we will never clear.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220302131544.3166154-3-Niklas.Cassel@wdc.com
The PLIC supports a fixed number of contexts (15872).
Each context has fixed register offsets in PLIC.
The number of contexts that we need to initialize depends on the privilege
modes supported by each hart. Therefore, this mapping between PLIC context
registers to hart privilege modes is platform specific, and is currently
supplied via device tree.
For example, canaan,k210 has the following mapping:
Context0: hart0 M-mode
Context1: hart0 S-mode
Context2: hart1 M-mode
Context3: hart1 S-mode
While sifive,fu540 has the following mapping:
Context0: hart0 M-mode
Context1: hart1 M-mode
Context2: hart1 S-mode
Because the number of contexts per hart is not fixed, the names
ENABLE_PER_HART and CONTEXT_PER_HART for the register offsets are quite
confusing and might mislead the reader to think that these are fixed
register offsets per hart.
Rename the offsets to more clearly highlight that these are per PLIC
context and not per hart.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220302131544.3166154-2-Niklas.Cassel@wdc.com
* irq/qcom-pdc-cleanup:
: .
: Spring cleanup for the Qualcomm PDC driver, simplifying its
: use of irq domains, replacing open-coded functionnalities with
: the core code equivalent, and fixing the dodgy locking.
: .
irqchip/qcom-pdc: Drop open coded version of __assign_bit()
irqchip/qcom-pdc: Fix broken locking
irqchip/qcom-pdc: Kill qcom_pdc_translate helper
irqchip/qcom-pdc: Kill non-wakeup irqdomain
irqchip/qcom-pdc: Kill PDC_NO_PARENT_IRQ
Signed-off-by: Marc Zyngier <maz@kernel.org>
smatch warning was reported as below ->
smatch warnings:
drivers/irqchip/irq-nvic.c:131 nvic_of_init()
warn: 'nvic_base' not released on lines: 97.
Release nvic_base upon failure.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Souptick Joarder (HPE) <jrdr.linux@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220218163303.33344-1-jrdr.linux@gmail.com
The driver uses what looks like an open-coded version of __assign_bit().
Replace it with the real thing.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Maulik Shah <quic_mkshah@quicinc.com>
Link: https://lore.kernel.org/r/20220224101226.88373-6-maz@kernel.org
pdc_enable_intr() serves as a primitive to qcom_pdc_gic_{en,dis}able,
and has a raw spinlock for mutual exclusion, which is uses with
interruptible primitives.
This means that this critical section can itself be interrupted.
Should the interrupt also be a PDC interrupt, and the endpoint driver
perform an irq_disable() on that interrupt, we end-up in a deadlock.
Fix this by using the irqsave/irqrestore variants of the locking
primitives.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Maulik Shah <quic_mkshah@quicinc.com>
Link: https://lore.kernel.org/r/20220224101226.88373-5-maz@kernel.org
qcom_pdc_translate() really is nothing but an open coded version
of irq_domain_translate_twocell(). Get rid of it and use the common
version instead.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Maulik Shah <quic_mkshah@quicinc.com>
Link: https://lore.kernel.org/r/20220224101226.88373-4-maz@kernel.org
A careful look at the way the PDC driver works shows that:
- all interrupts are in the same space
- all interrupts are treated the same
And yet the driver creates two domains based on whether
the interrupt gets mapped directly or from the pinctrl code,
which is obviously a waste of resources.
Kill the non-wakeup domain and unify all the interrupt handling.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220224101226.88373-3-maz@kernel.org
PDC_NO_PARENT_IRQ is pretty pointless, as all it indicates is
that the PDC terminates the interrupt hierarchy. Which is
exactly the same as not having a mapping in the GIC space.
This is also bad practice to treat the absence of a hwirq
as a hwirq itself.
Just explicitly use the region mapping pointer, and drop
the definition.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Maulik Shah <quic_mkshah@quicinc.com>
Link: https://lore.kernel.org/r/20220224101226.88373-2-maz@kernel.org
A dsb(ishst) barrier should be enough to order previous writes with
the system register generating the SGI, as we only need to guarantee
the visibility of data to other CPUs in the inner shareable domain
before we send the SGI.
A micro-benchmark is written to verify the performance impact on
kunpeng920 machine with 2 sockets, each socket has 2 dies, and
each die has 24 CPUs, so totally the system has 2 * 2 * 24 = 96
CPUs. ~2% performance improvement can be seen by this benchmark.
The code of benchmark module:
#include <linux/module.h>
#include <linux/timekeeping.h>
volatile int data0 ____cacheline_aligned;
volatile int data1 ____cacheline_aligned;
volatile int data2 ____cacheline_aligned;
volatile int data3 ____cacheline_aligned;
volatile int data4 ____cacheline_aligned;
volatile int data5 ____cacheline_aligned;
volatile int data6 ____cacheline_aligned;
static void ipi_latency_func(void *val)
{
}
static int __init ipi_latency_init(void)
{
ktime_t stime, etime, delta;
int cpu, i;
int start = smp_processor_id();
stime = ktime_get();
for ( i = 0; i < 1000; i++)
for (cpu = 0; cpu < 96; cpu++) {
data0 = data1 = data2 = data3 = data4 = data5 = data6 = cpu;
smp_call_function_single(cpu, ipi_latency_func, NULL, 1);
}
etime = ktime_get();
delta = ktime_sub(etime, stime);
printk("%s ipi from cpu%d to cpu0-95 delta of 1000times:%lld\n",
__func__, start, delta);
return 0;
}
module_init(ipi_latency_init);
static void ipi_latency_exit(void)
{
}
module_exit(ipi_latency_exit);
MODULE_DESCRIPTION("IPI benchmark");
MODULE_LICENSE("GPL");
run the below commands 10 times on both Vanilla and the kernel with this
patch:
# taskset -c 0 insmod test.ko
# rmmod test
The result on vanilla:
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:126757449
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:126784249
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:126177703
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:127022281
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:126184883
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:127374585
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:125778089
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:126974441
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:127357625
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:126228184
The result on the kernel with this patch:
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:124467401
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:123474209
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:123558497
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:122993951
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:122984223
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:123323609
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:124507583
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:123386963
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:123340664
ipi_latency_init ipi from cpu0 to cpu0-95 delta of 1000times:123285324
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
[maz: tidied up commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220220061910.6155-1-21cnbao@gmail.com
* irq/print_chip:
: .
: Convert irqchip drivers that use the .name field as a topology
: description to the .irq_print_chip callback, which allows the
: name to be made dymanic. The irq_chip structures are then made
: 'const' in order to prevent further abuse.
: .
irqchip/versatile-fpga: Switch to dynamic chip name output
irqchip/ts4800: Switch to dynamic chip name output
irqchip/mvebu-pic: Switch to dynamic chip name output
irqchip/lpc32xx: Switch to dynamic chip name output
irqchip/gic: Switch to dynamic chip name output
genirq/debugfs: Use irq_print_chip() when provided by irqchip
genirq: Allow irq_chip registration functions to take a const irq_chip
irqdomain: Let irq_domain_set_{info,hwirq_and_chip} take a const irq_chip
Signed-off-by: Marc Zyngier <maz@kernel.org>
Move the name output to the relevant callback, which allows us
some nice cleanups (mostly owing to the fact that the driver is
now DT only.
We also drop a random include directive from the ftintc010 driver.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220209162607.1118325-8-maz@kernel.org
Instead of overriding the name field, track the corresponding device
and use the relevant callback to output its name.
This allows us to make the irq_chip structure const.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220209162607.1118325-6-maz@kernel.org
Instead of overriding the name field with the device name, use
the relevant callback. This allows us to make the irq_chip structure
const.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220209162607.1118325-5-maz@kernel.org
The last dynamic aspect of the GIC's irq_chip structure is the
name that is associated to it.
Move the output of that name to the relevant callback, which
allows us to do a bit of cleanup and mark the structures const.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220209162607.1118325-4-maz@kernel.org
* irq/parent_device:
: .
: Move irq_chip::parent_device to irq_domain::dev to track the
: PM state of the device implementing the irqchip.
: .
genirq: Kill irq_chip::parent_device
pinctrl: starfive: Move PM device over to irq domain
pinctrl: npcm: Fix broken references to chip->parent_device
gpio: tpmx86: Move PM device over to irq domain
gpio: rcar: Move PM device over to irq domain
gpio: omap: Move PM device over to irq domain
gpio: mt7621: Kill parent_device usage
irqchip/imx-intmux: Move PM device over to irq domain
irqchip/renesas-irqc: Move PM device over to irq domain
irqchip/renesas-intc-irqpin: Move PM device over to irq domain
irqchip/gic: Move PM device over to irq domain
genirq: Allow the PM device to originate from irq domain
Signed-off-by: Marc Zyngier <maz@kernel.org>
Enhance stm32-exti driver to support STM32MP13 SoC. This SoC uses the same
hardware version than STM32MP15. Only EXTI line mapping is changed and
following EXTI lines are supported: GPIO, RTC, I2C[1-5], UxART[1-8],
USBH_EHCI, USBH_OHCI, USB_OTG, LPTIM[1-5], ETH[1-2].
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220202140005.860-3-alexandre.torgue@foss.st.com
Move the reference to the device over to the irq domain.
This allows the irq_chip structure to be directly used instead
of taking a copy for each instance.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bartosz Golaszewski <brgl@bgdev.pl>
Link: https://lore.kernel.org/r/20220201120310.878267-6-maz@kernel.org
Move the reference to the device over to the irq domain.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Bartosz Golaszewski <brgl@bgdev.pl>
Link: https://lore.kernel.org/r/20220201120310.878267-5-maz@kernel.org
Move the reference to the device over to the irq domain.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Bartosz Golaszewski <brgl@bgdev.pl>
Link: https://lore.kernel.org/r/20220201120310.878267-4-maz@kernel.org
Move the reference to the GIC device over to the irq domain.
This allows for some localised cleanup.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Bartosz Golaszewski <brgl@bgdev.pl>
Link: https://lore.kernel.org/r/20220201120310.878267-3-maz@kernel.org
As we are about to have a PMU driver, move the PMU bits from the AIC
driver into a common include file.
Reviewed-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Marc Zyngier <maz@kernel.org>
