Rely on page_pool_recycle_direct and not on xdp_return_buff in
mvneta_run_xdp. This is a preliminary patch to limit the dma sync len
to the one strictly necessary
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 8033 suggests an alternative approach to calculate the queue
delay in PIE by using a timestamp on every enqueued packet. This
patch adds an implementation of that approach and sets it as the
default method to calculate queue delay. The previous method (based
on Little's law) to calculate queue delay is set as optional.
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Acked-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rahul Lakkireddy says:
====================
cxgb4: add TC-MATCHALL classifier offload
This series of patches add support to offload TC-MATCHALL classifier
to hardware to classify all outgoing and incoming traffic on the
underlying port. Only 1 egress and 1 ingress rule each can be
offloaded on the underlying port.
Patch 1 adds support for TC-MATCHALL classifier offload on the egress
side. TC-POLICE is the only action that can be offloaded on the egress
side and is used to rate limit all outgoing traffic to specified max
rate.
Patch 2 adds logic to reject the current rule offload if its priority
conflicts with existing rules in the TCAM.
Patch 3 adds support for TC-MATCHALL classifier offload on the ingress
side. The same set of actions supported by existing TC-FLOWER
classifier offload can be applied on all the incoming traffic.
v5:
- Fixed commit message and comment to include comparison for equal
priority in patch 2.
v4:
- Removed check in patch 1 to reject police offload if prio is not 1.
- Moved TC_SETUP_BLOCK code to separate function in patch 1.
- Added logic to ensure the prio passed by TC doesn't conflict with
other rules in TCAM in patch 2.
- Higher index has lower priority than lower index in TCAM. So, rework
cxgb4_get_free_ftid() to search free index from end of TCAM in
descending order in patch 2.
- Added check to ensure the matchall rule's prio doesn't conflict with
other rules in TCAM in patch 3.
- Added logic to fill default mask for VIID, if none has been
provided, to prevent conflict with duplicate VIID rules in patch 3.
- Used existing variables in private structure to fill VIID info,
instead of extracting the info manually in patch 3.
v3:
- Added check in patch 1 to reject police offload if prio is not 1.
- Assign block_shared variable only for TC_SETUP_BLOCK in patch 1.
v2:
- Added check to reject flow block sharing for policers in patch 1.
- Removed logic to fetch free index from end of TCAM in patch 2.
Must maintain the same ordering as in kernel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TC-MATCHALL classifier ingress offload support. The same actions
supported by existing TC-FLOWER offload can be applied to all incoming
traffic on the underlying interface.
Ensure the rule priority doesn't conflict with existing rules in the
TCAM. Only 1 ingress matchall rule can be active at a time on the
underlying interface.
v5:
- No change.
v4:
- Added check to ensure the matchall rule's prio doesn't conflict with
other rules in TCAM.
- Added logic to fill default mask for VIID, if none has been
provided, to prevent conflict with duplicate VIID rules.
- Used existing variables in private structure to fill VIID info,
instead of extracting the info manually.
v3:
- No change.
v2:
- Removed logic to fetch free index from end of TCAM. Must maintain
same ordering as in kernel.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only offload rule if it satisfies both of the following conditions:
1. The immediate previous rule has priority <= current rule's priority.
2. The immediate next rule has priority >= current rule's priority.
Also rework free entry fetch logic to search from end of TCAM, instead
of beginning, because higher indices have lower priority than lower
indices. This is similar to how TC auto generates priority values.
v5:
- Fixed commit message and comment to include comparison for equal
priority.
v4:
- Patch added in this version.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TC-MATCHALL classifier offload with TC-POLICE action applied for
all outgoing traffic on the underlying interface. Split flow block
offload to support both egress and ingress classification.
For example, to rate limit all outgoing traffic to 1 Gbps:
$ tc qdisc add dev enp2s0f4 clsact
$ tc filter add dev enp2s0f4 egress matchall skip_sw \
action police rate 1Gbit burst 8Kbit
Note that skip_sw is important. Otherwise, both stack and hardware
will end up doing policing. Policing can't be shared across flow
blocks. Only 1 egress matchall rule can be active at a time on the
underlying interface.
v5:
- No change.
v4:
- Removed check to reject police offload if prio is not 1.
- Moved TC_SETUP_BLOCK code to separate function.
v3:
- Added check to reject police offload if prio is not 1.
- Assign block_shared variable only for TC_SETUP_BLOCK.
v2:
- Added check to reject flow block sharing for policers.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
page_pool: API for numa node change handling
This series extends page pool API to allow page pool consumers to update
page pool numa node on the fly. This is required since on some systems,
rx rings irqs can migrate between numa nodes, due to irq balancer or user
defined scripts, current page pool has no way to know of such migration
and will keep allocating and holding on to pages from a wrong numa node,
which is bad for the consumer performance.
1) Add API to update numa node id of the page pool
Consumers will call this API to update the page pool numa node id.
2) Don't recycle non-reusable pages:
Page pool will check upon page return whether a page is suitable for
recycling or not.
2.1) when it belongs to a different num node.
2.2) when it was allocated under memory pressure.
3) mlx5 will use the new API to update page pool numa id on demand.
The series is a joint work between me and Jonathan, we tested it and it
proved itself worthy to avoid page allocator bottlenecks and improve
packet rate and cpu utilization significantly for the described
scenarios above.
Performance testing:
XDP drop/tx rate and TCP single/multi stream, on mlx5 driver
while migrating rx ring irq from close to far numa:
mlx5 internal page cache was locally disabled to get pure page pool
results.
CPU: Intel(R) Xeon(R) CPU E5-2603 v4 @ 1.70GHz
NIC: Mellanox Technologies MT27700 Family [ConnectX-4] (100G)
XDP Drop/TX single core:
NUMA | XDP | Before | After
---------------------------------------
Close | Drop | 11 Mpps | 10.9 Mpps
Far | Drop | 4.4 Mpps | 5.8 Mpps
Close | TX | 6.5 Mpps | 6.5 Mpps
Far | TX | 3.5 Mpps | 4 Mpps
Improvement is about 30% drop packet rate, 15% tx packet rate for numa
far test.
No degradation for numa close tests.
TCP single/multi cpu/stream:
NUMA | #cpu | Before | After
--------------------------------------
Close | 1 | 18 Gbps | 18 Gbps
Far | 1 | 15 Gbps | 18 Gbps
Close | 12 | 80 Gbps | 80 Gbps
Far | 12 | 68 Gbps | 80 Gbps
In all test cases we see improvement for the far numa case, and no
impact on the close numa case.
==================
Performance analysis and conclusions by Jesper [1]:
Impact on XDP drop x86_64 is inconclusive and shows only 0.3459ns
slow-down, as this is below measurement accuracy of system.
v2->v3:
- Rebase on top of latest net-next and Jesper's page pool object
release patchset [2]
- No code changes
- Performance analysis by Jesper added to the cover letter.
v1->v2:
- Drop last patch, as requested by Ilias and Jesper.
- Fix documentation's performance numbers order.
[1] https://github.com/xdp-project/xdp-project/blob/master/areas/mem/page_pool04_inflight_changes.org#performance-notes
[2] https://patchwork.ozlabs.org/cover/1192098/
====================
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once every napi poll cycle, check if numa node is different than
the page pool's numa id, and update it using page_pool_update_nid().
Alternatively, we could have registered an irq affinity change handler,
but page_pool_update_nid() must be called from napi context anyways, so
the handler won't actually help.
Performance testing:
XDP drop/tx rate and TCP single/multi stream, on mlx5 driver
while migrating rx ring irq from close to far numa:
mlx5 internal page cache was locally disabled to get pure page pool
results.
CPU: Intel(R) Xeon(R) CPU E5-2603 v4 @ 1.70GHz
NIC: Mellanox Technologies MT27700 Family [ConnectX-4] (100G)
XDP Drop/TX single core:
NUMA | XDP | Before | After
---------------------------------------
Close | Drop | 11 Mpps | 10.9 Mpps
Far | Drop | 4.4 Mpps | 5.8 Mpps
Close | TX | 6.5 Mpps | 6.5 Mpps
Far | TX | 3.5 Mpps | 4 Mpps
Improvement is about 30% drop packet rate, 15% tx packet rate for numa
far test.
No degradation for numa close tests.
TCP single/multi cpu/stream:
NUMA | #cpu | Before | After
--------------------------------------
Close | 1 | 18 Gbps | 18 Gbps
Far | 1 | 15 Gbps | 18 Gbps
Close | 12 | 80 Gbps | 80 Gbps
Far | 12 | 68 Gbps | 80 Gbps
In all test cases we see improvement for the far numa case, and no
impact on the close numa case.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A page is NOT reusable when at least one of the following is true:
1) allocated when system was under some pressure. (page_is_pfmemalloc)
2) belongs to a different NUMA node than pool->p.nid.
To update pool->p.nid users should call page_pool_update_nid().
Holding on to such pages in the pool will hurt the consumer performance
when the pool migrates to a different numa node.
Performance testing:
XDP drop/tx rate and TCP single/multi stream, on mlx5 driver
while migrating rx ring irq from close to far numa:
mlx5 internal page cache was locally disabled to get pure page pool
results.
CPU: Intel(R) Xeon(R) CPU E5-2603 v4 @ 1.70GHz
NIC: Mellanox Technologies MT27700 Family [ConnectX-4] (100G)
XDP Drop/TX single core:
NUMA | XDP | Before | After
---------------------------------------
Close | Drop | 11 Mpps | 10.9 Mpps
Far | Drop | 4.4 Mpps | 5.8 Mpps
Close | TX | 6.5 Mpps | 6.5 Mpps
Far | TX | 3.5 Mpps | 4 Mpps
Improvement is about 30% drop packet rate, 15% tx packet rate for numa
far test.
No degradation for numa close tests.
TCP single/multi cpu/stream:
NUMA | #cpu | Before | After
--------------------------------------
Close | 1 | 18 Gbps | 18 Gbps
Far | 1 | 15 Gbps | 18 Gbps
Close | 12 | 80 Gbps | 80 Gbps
Far | 12 | 68 Gbps | 80 Gbps
In all test cases we see improvement for the far numa case, and no
impact on the close numa case.
The impact of adding a check per page is very negligible, and shows no
performance degradation whatsoever, also functionality wise it seems more
correct and more robust for page pool to verify when pages should be
recycled, since page pool can't guarantee where pages are coming from.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add page_pool_update_nid() to be called by page pool consumers when they
detect numa node changes.
It will update the page pool nid value to start allocating from the new
effective numa node.
This is to mitigate page pool allocating pages from a wrong numa node,
where the pool was originally allocated, and holding on to pages that
belong to a different numa node, which causes performance degradation.
For pages that are already being consumed and could be returned to the
pool by the consumer, in next patch we will add a check per page to avoid
recycling them back to the pool and return them to the page allocator.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grygorii Strashko says:
====================
net: ethernet: ti: introduce new cpsw switchdev based driver
Thank you All for review of v6.
There are no significant changes in this version, just fixed comments to v6.
--- v6
The major change in this version is DT bindings conversation to json-schema, and
fixed other comments to v5. Also added patch to clean up ALE on init and netif
restart.
--- v5
The major part of work done in this iteration is rebasing on top of net-next
with XDP series from Ivan Khoronzhuk [3], and enable XDP support in the new
CPSW switchdev driver (it was little bit painful ;(). There are mostly no
functional changes in new CPSW driver, just few fixes, sync with old driver
and cleanups/optimizations. So, I've kept rest of cover letter unchanged.
---
This series originally based on work [1][2] done by
Ilias Apalodimas <ilias.apalodimas@linaro.org>.
This the RFC v5 which introduces new CPSW switchdev based driver which is
operating in dual-emac mode by default, thus working as 2 individual
network interfaces. The Switch mode can be enabled by configuring devlink driver
parameter "switch_mode" to 1/true:
devlink dev param set platform/48484000.switch \
name switch_mode value 1 cmode runtime
This can be done regardless of the state of Port's netdev devices - UP/DOWN, but
Port's netdev devices have to be in UP before joining the bridge to avoid
overwriting of bridge configuration as CPSW switch driver completely reloads its
configuration when first Port changes its state to UP.
When the both interfaces joined the bridge - CPSW switch driver will start
marking packets with offload_fwd_mark flag unless "ale_bypass=0".
All configuration is implemented via switchdev API.
The previous solution of tracking both Ports joined the bridge
(from netdevice_notifier) proved to be not correct as changing CPSW switch
driver mode required cleanup of ALE table and CPSW settings which happens
while second Port is joined bridge and as result configuration loaded
by bridge for the first Port became corrupted.
The introduction of the new CPSW switchdev based driver (cpsw_new.c) is split
on two parts: Part 1 - basic dual-emac driver; Part 2 switchdev support.
Such approach has simplified code development and testing alot. And, I hope,
it will help with better review.
patches #1 - 5: preparation patches which also moves common code to cpsw_priv.c
patches #6 - 9: Introduce TI CPSW switch driver based on switchdev and new
DT bindings
patch #10: new CPSW switchdev driver documentation
patch #11: adds DT nodes for new CPSW switchdev driver added for DRA7 SoC
patch #12: adds DT nodes for new cpsw switchdev driver for am571x-idk board
patch #13: enables build of TI CPSW driver
Most of the contents of the previous cover-letter have been added in
new driver documentation, so please refer to that for configuration,
testing and future work.
These patches can be found at (branch contains some additional patches required
for testing on top of net-next):
https://github.com/grygoriyS/linux.git
branch: lkml-5.4-switch-tbd-v7
changes in v7:
- patch 2: added check for devm_kmalloc_array() return value
- patch 6: fixed comments
changes in v6: https://lkml.org/lkml/2019/11/9/108
- DT bindings converted to json-schema
- netdev initialization is split on creation and registration.
The netdevs registration happens now at the end of the pobe.
- reworked cpsw_set_pauseparam() to use PHYlib APIs.
- other comments for v5 fixed
v5: https://patchwork.kernel.org/cover/11208785/
- rebase on top of net-next with XDP series from Ivan Khoronzhuk [3],
and enable XDP support in the new CPSW switchdev driver
cpsw driver (tested XDP_DROP only)
- sync with old cpsw driver
- implement comments from Ivan Khoronzhuk and Rob Herring
- fixed "NETDEV WATCHDOG: .." warning after interface after interface UP/DOWN,
missed TX wake in cpsw_adjust_link()
v4: https://patchwork.kernel.org/cover/11010523/
- finished split of common CPSW code
- added devlink support
- changed CPSW mode configuration approach: from netdevice_notifier to devlink
parameter
- refactor and clean up ALE changes which allows to modify VLANs/MDBs entries
- added missed support for port QDISC_CBS and QDISC_MQPRIO
- the CPSW is split on two parts: basic dual_mac driver and switchdev support
- added missed callback .ndo_get_port_parent_id()
- reworked ingress frames marking in switch mode (offload_fwd_mark)
- applied comments from Andrew Lunn
v3: https://lwn.net/Articles/786677/
Changes in v3:
- alot of work done to split properly common code between legacy and switchdev
CPSW drivers and clean up code
- CPSW switchdev interface updated to the current LKML switchdev interface
- actually new CPSW switchdev based driver introduced
- optimized dual_mac mode in new driver. Main change is that in promiscuous
mode P0_UNI_FLOOD (both ports) is enabled in addition to ALLMULTI (current
port) instead of ALE_BYPASS. So, port in non promiscuous mode will keep
possibility of mcast and vlan filtering.
- changed bridge join sequnce: now switch mode will be enabled only when
both ports joined the bridge. CPSW will be switched to dual_mac mode if any
port leave bridge. ALE table is completly cleared and then refiled while
switching to switch mode - this simplidies code a lot, but introduces some
limitation to bridge setup sequence:
ip link add name br0 type bridge
ip link set dev br0 type bridge ageing_time 1000
ip link set dev br0 type bridge vlan_filtering 0 <- disable
echo 0 > /sys/class/net/br0/bridge/default_vlan
ip link set dev sw0p1 up <- add ports
ip link set dev sw0p2 up
ip link set dev sw0p1 master br0
ip link set dev sw0p2 master br0
echo 1 > /sys/class/net/br0/bridge/default_vlan <- enable
ip link set dev br0 type bridge vlan_filtering 1
bridge vlan add dev br0 vid 1 pvid untagged self
- STP tested with vlan_filtering 1/0. To make STP work I've had to set
NO_SA_UPDATE for all slave ports (see comment in code). It also required to
statically register STP mcast address {0x01, 0x80, 0xc2, 0x0, 0x0, 0x0};
- allowed build both TI_CPSW and TI_CPSW_SWITCHDEV drivers
- PTP can be enabled on both ports in dual_mac mode
[1] https://patchwork.ozlabs.org/cover/929367/
[2] https://patches.linaro.org/cover/136709/
[3] https://patchwork.kernel.org/cover/11035813/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add CONFIG_TI_CPSW_SWITCHDEV option to enable new cpsw switchdev driver
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DT nodes for new cpsw switchdev driver for am571x-idk board for now to
enable testing of the new solution.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DT nodes for new cpsw switch dev driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new cpsw dirver based on switchdev was added. Add documentation about
basic configuration and future features
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dependency from TI_CPSW_SWITCHDEV.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW switchdev based driver which is operating in dual-emac mode by
default, thus working as 2 individual network interfaces. The Switch mode
can be enabled by configuring devlink driver parameter "switch_mode" to 1:
devlink dev param set platform/48484000.switch \
name switch_mode value 1 cmode runtime
This can be done regardless of the state of Port's netdevs - UP/DOWN, but
Port's netdev devices have to be UP before joining the bridge to avoid
overwriting of bridge configuration as CPSW switch driver completely
reloads its configuration when first Port changes its state to UP.
When the both interfaces joined the bridge - CPSW switch driver will start
marking packets with offload_fwd_mark flag unless "ale_bypass=0".
All configuration is implemented via switchdev API and notifiers.
Supported:
- SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS
- SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS: BR_MCAST_FLOOD
- SWITCHDEV_ATTR_ID_PORT_STP_STATE
- SWITCHDEV_OBJ_ID_PORT_VLAN
- SWITCHDEV_OBJ_ID_PORT_MDB
- SWITCHDEV_OBJ_ID_HOST_MDB
Hence CPSW switchdev driver supports:
- FDB offloading
- MDB offloading
- VLAN filtering and offloading
- STP
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part 1:
Introduce basic CPSW dual_mac driver (cpsw_new.c) which is operating in
dual-emac mode by default, thus working as 2 individual network interfaces.
Main differences from legacy CPSW driver are:
- optimized promiscuous mode: The P0_UNI_FLOOD (both ports) is enabled in
addition to ALLMULTI (current port) instead of ALE_BYPASS. So, Ports in
promiscuous mode will keep possibility of mcast and vlan filtering, which
is provides significant benefits when ports are joined to the same bridge,
but without enabling "switch" mode, or to different bridges.
- learning disabled on ports as it make not too much sense for
segregated ports - no forwarding in HW.
- enabled basic support for devlink.
devlink dev show
platform/48484000.switch
devlink dev param show
platform/48484000.switch:
name ale_bypass type driver-specific
values:
cmode runtime value false
- "ale_bypass" devlink driver parameter allows to enable
ALE_CONTROL(4).BYPASS mode for debug purposes.
- updated DT bindings.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add bindings for the new TI CPSW switch driver. Comparing to the legacy
bindings (net/cpsw.txt):
- ports definition follows DSA bindings (net/dsa/dsa.txt) and ports can be
marked as "disabled" if not physically wired.
- all deprecated properties dropped;
- all legacy propertiies dropped which represent constant HW cpapbilities
(cpdma_channels, ale_entries, bd_ram_size, mac_control, slaves,
active_slave)
- TI CPTS DT properties are reused as is, but grouped in "cpts" sub-node
- TI Davinci MDIO DT bindings are reused as is, because Davinci MDIO is
reused.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to add support for a switchdev based cpsw driver,
move common functions to cpsw-priv.c so that they can be used across both
drivers.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A following patches introduce new CPSW switchdev driver which uses common
code with legacy CPSW driver. This will introduce build dependency between
CPSW switchdev and CPSW legacy drivers related to for_each_slave() and
cpsw_slave_index() - they can be compiled both, but only one of them will
be not functional depending in Kconfig settings due to duffrences in Slave
Ports indexes calculation.
To fix this make for_each_slave() local (it's used now only by legacy CPSW
driver) and convert cpsw_slave_index() to be a function pointer which is
assigned in probe. Driver to probe is defined by DT.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A following patch introduces switchdev functionality, so modify
ALE engine VLANs/MDBs API:
- cpsw_ale_del_mcast(): update so it will remove only selected ports from
mcast port_mask or delete whole mcast record if !port_mask
- cpsw_ale_del_vlan(): update so it will remove only selected ports from
all VLAN record's masks or delete whole VLAN record if !port_mask
- add cpsw_ale_vlan_add_modify() to add or modify existing VLAN record's
masks
- add cpsw_ale_set_unreg_mcast() for enabling unreg mcast on port VLANs
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now untagged vlan traffic is not support on Host P0 port. This patch adds
in ALE context bitmap of VLANs for which Host P0 port bit set in Force
Untagged Packet Egress bitmask in VLANs ALE entries, and adds corresponding
check in VLAN incapsulation header parsing function cpsw_rx_vlan_encap().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean CPSW ALE on init and intf restart (up/down) to avoid reading obsolete
or garbage entries from ALE table.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
nf_tables_offload: vlan matching support
The following patchset contains Netfilter support for vlan matching
offloads:
1) Constify nft_reg_load() as a preparation patch.
2) Restrict rule matching to ingress interface type ARPHRD_ETHER.
3) Add new vlan_tci field to flow_dissector_key_vlan structure,
to allow to set up vlan_id, vlan_dei and vlan_priority in one go.
4) C-VLAN matching support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Match on h_vlan_encapsulated_proto and set up protocol dependency. Check
for protocol dependency before accessing the tci field. Allow to match
on the encapsulated ethertype too.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Match on ethertype and set up protocol dependency. Check for protocol
dependency before accessing the tci field. Allow to match on the
encapsulated ethertype too.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware offload support at this stage assumes an ethernet device in
place. The flow dissector provides the intermediate representation to
express this selector, so extend it to allow to store the interface
type. Flower does not uses this, so skb_flow_dissect_meta() is not
extended to match on this new field.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch constifies the pointer to source register data that is passed
as an input parameter.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
geneve RFC (draft-ietf-nvo3-geneve-14) allows a geneve packet to carry
multiple geneve opts, so it's necessary for lwtunnel to support adding
multiple geneve opts in one lwtunnel route. But vxlan and erspan opts
are still only allowed to add one option.
With this patch, iproute2 could make it like:
# ip r a 1.1.1.0/24 encap ip id 1 geneve_opts 0:0:12121212,1:2:12121212 \
dst 10.1.0.2 dev geneve1
# ip r a 1.1.1.0/24 encap ip id 1 vxlan_opts 456 \
dst 10.1.0.2 dev erspan1
# ip r a 1.1.1.0/24 encap ip id 1 erspan_opts 1:123:0:0 \
dst 10.1.0.2 dev erspan1
Which are pretty much like cls_flower and act_tunnel_key.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Semicolon is not required at the end of switch block. So, remove it.
Addresses coccinelle warning:
drivers/net/ethernet/chelsio/cxgb4/sge.c:2260:2-3: Unneeded semicolon
Fixes: 4846d5330d ("cxgb4: add Tx and Rx path for ETHOFLD traffic")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the NXP LS1028A, there are 2 Ethernet links between the Felix switch
and the ENETC:
- eno2 <-> swp4, at 2.5G
- eno3 <-> swp5, at 1G
Only one of the above Ethernet port pairs can act as a DSA link for
tagging.
When adding initial support for the driver, it was tested only on the 1G
eno3 <-> swp5 interface, due to the necessity of using PHYLIB initially
(which treats fixed-link interfaces as emulated C22 PHYs, so it doesn't
support fixed-link speeds higher than 1G).
After making PHYLINK work, it appears that swp4 still can't act as CPU
port. So it looks like ocelot_set_cpu_port was being called for swp4,
but then it was called again for swp5, overwriting the CPU port assigned
in the DT.
It appears that when you call dsa_upstream_port for a port that is not
defined in the device tree (such as swp5 when using swp4 as CPU port),
its dp->cpu_dp pointer is not initialized by dsa_tree_setup_default_cpu,
and this trips up the following condition in dsa_upstream_port:
if (!cpu_dp)
return port;
So the moral of the story is: don't call dsa_upstream_port for a port
that is not defined in the device tree, and therefore its dsa_port
structure is not completely initialized (ds->num_ports is still 6).
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case where the call to phy_interface_is_rgmii returns zero
the variable ret is left uninitialized and this is returned at
the end of the function dp83869_configure_rgmii. Fix this by
returning 0 instead of the uninitialized value in ret.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 01db923e83 ("net: phy: dp83869: Add TI dp83869 phy")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
LWTUNNEL_IP_OPT_ERSPAN_VER is u8 type, and nla_put_u8 should have
been used instead of nla_put_u32(). This is a copy-paste error.
Fixes: b0a21810bd ("lwtunnel: add options setting and dumping for erspan")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Updates.
This series has the firmware interface update that changes the aRFS/ntuple
interface on 57500 chips. The 2nd patch adds a counter and improves
the hardware buffer error handling on the 57500 chips. The rest of the
series is mainly enhancements on error recovery and firmware reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is especially beneficial during the NVRAM related firmware
commands that have longer timeouts. If the BNXT_STATE_FW_FATAL_COND
flag gets set while waiting for firmware response, abort and return
error.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During loss of heartbeat, log this warning message.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For NVM params that are not supported in the current NVM
configuration, return the error as -EOPNOTSUPP.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report health status update to devlink health reporter, once
reset is completed.
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux driver is capable of being the master function to handle
resets, so we set the flag to let firmware know. Some other
drivers, such as DPDK, is not capable and will not set the flag.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If firmware supports hot reset, extend ETHTOOL_RESET to support
hot reset driver which does not require a driver reload after
ETHTOOL_RESET. The driver will go through the same coordinated
reset sequence as a firmware initiated fatal/non-fatal reset.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the larger HWRM_COREDUMP_TIMEOUT value for coredump related
data response from the firmware. These commands take longer than
normal commands.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hardware reports RX buffer errors, the latest 57500 chips do not
require reset. The packet is discarded by the hardware and the
ring will continue to operate.
Also, add an rx_buf_errors counter for this type of error. It can help
the user to identify if the aggregation ring is too small.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The aRFS ring table interface has changed for the 57500 chips. Updating
it accordingly so it will work with the latest production firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
selftests: Add ethtool and scale tests
This patch set adds generic ethtool tests and a mlxsw-specific router
scale test for Spectrum-2.
Patches #1-#2 from Danielle add the router scale test for Spectrum-2. It
re-uses the same test as Spectrum-1, but it is invoked with a different
scale, according to what it is queried from devlink-resource.
Patches #3-#5 from Amit are a re-work of the ethtool tests that were
posted in the past [1]. Patches #3-#4 add the necessary library
routines, whereas patch #5 adds the test itself. The test checks both
good and bad flows with autoneg on and off. The test plan it detailed in
the commit message.
Last time Andrew and Florian (copied) provided very useful feedback that
is incorporated in this set. Namely:
* Parse the value of the different link modes from
/usr/include/linux/ethtool.h
* Differentiate between supported and advertised speeds and use the
latter in autoneg tests
* Make the test generic and move it to net/forwarding/ instead of being
mlxsw-specific
[1] https://patchwork.ozlabs.org/cover/1112903/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Check configurations and packets transference with different variations
of autoneg and speed.
Test plan:
1. Test force of same speed with autoneg off
2. Test force of different speeds with autoneg off (should fail)
3. One side is autoneg on and other side sets force of common speeds
4. One side is autoneg on and other side only advertises a subset of the
common speeds (one speed of the subset)
5. One side is autoneg on and other side only advertises a subset of the
common speeds. Check that highest speed is negotiated
6. Test autoneg on, but each side advertises different speeds (should
fail)
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function that waits for device with maximum number of iterations.
It enables to limit the waiting and prevent infinite loop.
This will be used by the subsequent patch which will set two ports to
different speeds in order to make sure they cannot negotiate a link.
Waiting for all the setup is limited with 10 minutes for each device.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions:
1. speeds_arr_get
The function returns an array of speed values from
/usr/include/linux/ethtool.h The array looks as follows:
[10baseT/Half] = 0,
[10baseT/Full] = 1,
...
2. ethtool_set:
params: cmd
The function runs ethtool by cmd (ethtool -s cmd) and checks if
there was an error in configuration
3. dev_speeds_get:
params: dev, with_mode (0 or 1), adver (0 or 1)
return value: Array of supported/Advertised link modes
with/without mode
* Example 1:
speeds_get swp1 0 0
return: 1000 10000 40000
* Example 2:
speeds_get swp1 1 1
return: 1000baseKX/Full 10000baseKR/Full 40000baseCR4/Full
4. common_speeds_get:
params: dev1, dev2, with_mode (0 or 1), adver (0 or 1)
return value: Array of common speeds of dev1 and dev2
* Example:
common_speeds_get swp1 swp2 0 0
return: 1000 10000
Assuming that swp1 supports 1000 10000 40000 and swp2 supports
1000 10000
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
