This patch adds support for uprobe on ARM64 architecture.
Unit tests for following have been done so far and they have been found
working
1. Step-able instructions, like sub, ldr, add etc.
2. Simulation-able like ret, cbnz, cbz etc.
3. uretprobe
4. Reject-able instructions like sev, wfe etc.
5. trapped and abort xol path
6. probe at unaligned user address.
7. longjump test cases
Currently it does not support aarch32 instruction probing.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We need to decide in some cases like uprobe instruction analysis that
whether the current mm context belongs to a 32 bit task or 64 bit.
This patch has introduced an unsigned flag variable in mm_context_t.
Currently, we set and clear TIF_32BIT depending on the condition that
whether an elf binary load sets personality for 32 bit or 64 bit
respectively.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
uprobe is registered at break_hook with a unique ESR code. So, when a
TRAP_BRKPT occurs, call_break_hook checks if it was for uprobe. If not,
then send a SIGTRAP to user.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
uprobe registers a handler at step_hook. So, single_step_handler now
checks for user mode as well if there is a valid hook.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ARM64 step exception does not have any syndrome information. So, it is
responsibility of exception handler to take care that they handle it
only if exception was raised for them.
Since kgdb_step_brk_fn() always returns 0, therefore we might have problem
when we will have other step handler registered as well.
This patch fixes kgdb_step_brk_fn() to return error in case of step handler
was not meant for kgdb.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
decode-insn code has to be reused by arm64 uprobe implementation as well.
Therefore, this patch protects some portion of kprobe code and renames few
other, so that decode-insn functionality can be reused by uprobe even when
CONFIG_KPROBES is not defined.
kprobe_opcode_t and struct arch_specific_insn are also defined by
linux/kprobes.h, when CONFIG_KPROBES is not defined. So, protect these
definitions in asm/probes.h.
linux/kprobes.h already includes asm/kprobes.h. Therefore, remove inclusion
of asm/kprobes.h from decode-insn.c.
There are some definitions like kprobe_insn and kprobes_handler_t etc can
be re-used by uprobe. So, it would be better to remove 'k' from their
names.
struct arch_specific_insn is specific to kprobe. Therefore, introduce a new
struct arch_probe_insn which will be common for both kprobe and uprobe, so
that decode-insn code can be shared. Modify kprobe code accordingly.
Function arm_probe_decode_insn() will be needed by uprobe as well. So make
it global.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Page mappings with full RWX permissions are a security risk. x86
has an option to walk the page tables and dump any bad pages.
(See e1a58320a3 ("x86/mm: Warn on W^X mappings")). Add a similar
implementation for arm64.
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[catalin.marinas@arm.com: folded fix for KASan out of bounds from Mark Rutland]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
max_addr was added as part of struct ptdump_info but has never actually
been used. Remove it.
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The page table dumping code always assumes it will be dumping to a
seq_file to userspace. Future code will be taking advantage of
the page table dumping code but will not need the seq_file. Make
the seq_file optional for these cases.
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ptdump_register currently initializes a set of page table information and
registers debugfs. There are uses for the ptdump option without wanting the
debugfs options. Split this out to make it a separate option.
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that we no longer allow live kernel PMDs to be split, it is safe to
start using the contiguous bit for kernel mappings. So set the contiguous
bit in the kernel page mappings for regions whose size and alignment are
suitable for this.
This enables the following contiguous range sizes for the virtual mapping
of the kernel image, and for the linear mapping:
granule size | cont PTE | cont PMD |
-------------+------------+------------+
4 KB | 64 KB | 32 MB |
16 KB | 2 MB | 1 GB* |
64 KB | 2 MB | 16 GB* |
* Only when built for 3 or more levels of translation. This is due to the
fact that a 2 level configuration only consists of PGDs and PTEs, and the
added complexity of dealing with folded PMDs is not justified considering
that 16 GB contiguous ranges are likely to be ignored by the hardware (and
16k/2 levels is a niche configuration)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In preparation of adding support for contiguous PTE and PMD mappings,
let's replace 'block_mappings_allowed' with 'page_mappings_only', which
will be a more accurate description of the nature of the setting once we
add such contiguous mappings into the mix.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that we take care not manipulate the live kernel page tables in a
way that may lead to TLB conflicts, the case where a table mapping is
replaced by a block mapping can no longer occur. So remove the handling
of this at the PUD and PMD levels, and instead, BUG() on any occurrence
of live kernel page table manipulations that modify anything other than
the permission bits.
Since mark_rodata_ro() is the only caller where the kernel mappings that
are being manipulated are actually live, drop the various conditional
flush_tlb_all() invocations, and add a single call to mark_rodata_ro()
instead.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We expect arch_teardown_dma_ops() to be called very late in a device's
life, after it has been removed from its bus, and thus after the IOMMU
bus notifier has run. As such, even if this funny little check did make
sense, it's unlikely to achieve what it thinks it's trying to do anyway.
It's a residual trace of an earlier implementation which didn't belong
here from the start; belatedly snuff it out.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Kprobes does not need its own homebrewed (and frankly inscrutable) sign
extension macro; just use the standard kernel functions instead. Since
the compiler actually recognises the sign-extension idiom of the latter,
we also get the small bonus of some nicer codegen, as each displacement
calculation helper then compiles to a single optimal SBFX instruction.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add a sysfs cpu_capacity attribute with which it is possible to read and
write (thus over-writing default values) CPUs capacity. This might be
useful in situations where values needs changing after boot.
The new attribute shows up as:
/sys/devices/system/cpu/cpu*/cpu_capacity
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
With the introduction of cpu capacity-dmips-mhz bindings, CPU capacities
can now be calculated from values extracted from DT and information
coming from cpufreq. Add parsing of DT information at boot time, and
complement it with cpufreq information. Also, store such information
using per CPU variables, as we do for arm.
Caveat: the information provided by this patch will start to be used in
the future. We need to #define arch_scale_cpu_capacity to something
provided in arch, so that scheduler's default implementation (which gets
used if arch_scale_cpu_capacity is not defined) is overwritten.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add support for the AMAC ethernet to the Broadcom Northstar2 SoC device
tree
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers using pinctrl-single,pins have #pinctrl-cells = <1>, while
pinctrl-single,bits need #pinctrl-cells = <2>.
Note that this patch can be optionally applied separately from the
driver changes as the driver supports also the legacy binding without
#pinctrl-cells.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit efd9e03fac ("arm64: Use static keys for CPU features")
introduced support for static keys in asm/cpufeature.h, including
linux/jump_label.h. When CC_HAVE_ASM_GOTO is not defined, this causes a
circular dependency via linux/atomic.h, asm/lse.h and asm/cpufeature.h.
This patch moves the capability macros out out of asm/cpufeature.h into
a separate asm/cpucaps.h and modifies some of the #includes accordingly.
Fixes: efd9e03fac ("arm64: Use static keys for CPU features")
Reported-by: Artem Savkov <asavkov@redhat.com>
Tested-by: Artem Savkov <asavkov@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
These hardware blocks are SoC-specific, so their compatible strings
should be SoC-specific as well. This change has no impact on the
actual behavior since it is controlled by the generic "simple-mfd",
"syscon" compatible strings.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add a CPU clock to every CPU node and CPU OPP tables to use the
generic cpufreq driver. All the CPUs in each cluster share the
same OPP table.
Note:
clock-latency-ns (300ns) was calculated based on the CPU-gear switch
sequencer spec; it takes 12 clock cycles on the sequencer running
at 50 MHz, plus a bit additional latency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Add a CPU clock to every CPU node and a CPU OPP table to use the
generic cpufreq driver.
Note:
clock-latency-ns (300ns) was calculated based on the CPU-gear switch
sequencer spec; it takes 12 clock cycles on the sequencer running
at 50 MHz, plus a bit additional latency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The System Control node has 0x10000 byte of registers. The current
reg size must be expanded to use the cpufreq driver because the
registers controlling CPU frequency are located at offset 0x8000.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
At the first system bring-up, I chose to use spin-table because ARM
Trusted Firmware was not ready for this platform at that moment.
Actually, these SoCs are equipped with EL3 and able to provide PSCI.
Now I finished porting the ATF BL31 for the UniPhier platform, so it
is ready to migrate to PSCI enable method.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Architecturally, TLBs are private to the (physical) CPU they're
associated with. But when multiple vcpus from the same VM are
being multiplexed on the same CPU, the TLBs are not private
to the vcpus (and are actually shared across the VMID).
Let's consider the following scenario:
- vcpu-0 maps PA to VA
- vcpu-1 maps PA' to VA
If run on the same physical CPU, vcpu-1 can hit TLB entries generated
by vcpu-0 accesses, and access the wrong physical page.
The solution to this is to keep a per-VM map of which vcpu ran last
on each given physical CPU, and invalidate local TLBs when switching
to a different vcpu from the same VM.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Since this board doesn't mount pull-up/down registers for
USB1_{OVC,PWEN} pins, we should enable bias setting to pull these
pins up/down.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Based on work for the r8a7796 by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Enable the exposed SD card slots in the DT of the r8a7796/salvator-x.
Based on work for the r8a7795/salvator-x by Ai Kyuse.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Replace hard-coded values of type of GIC interrupt and its flags with
respective macros from header to increase code readability
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Interrupt of type IRQ_TYPE_NONE is not allowed for GIC interrupts and
generates an error:
genirq: Setting trigger mode 0 for irq 16 failed (gic_set_type+0x0/0x68)
The GIC requires shared interrupts to be edge rising or level high.
Platform declares support for both. Arbitrarily choose level high
everywhere hoping it will work on each platform.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Alban Browaeys <alban.browaeys@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
This patch adds the Device Tree source for Exynos5433-based Samsung TM2E
board. TM2E board is very similar to the TM2 board so the
exynos5433-tm2e.dts includes the TM2 DTS and overrides the differences.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Ingi kim <ingi2.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds the Device Tree source for Exynos5433-based Samsung TM2
board.
This patch adds support for following devices:
1. basic SoC
- Initial booting for Samsung Exynos5433 SoC
- DRAM LPDDR3 (3GB)
- eMMC (32GB)
- ARM architecture timer
2. power management devices
- Sasmung S2MPS13 PMIC for the power supply
- CPUFREQ for big.LITTLE cores
- TMU for big.LITTLE cores and GPU
- ADC with thermistor to measure the temperature of AP/Battery/Charger
- Maxim MAX77843 Interface PMIC (MUIC/Haptic/Regulator)
3. sound devices
- I2S for sound bus
- LPASS for sound power control
- Wolfson WM5110 for sound codec
- Maxim MAX98504 for speaker amplifier
- TM2 ASoC Machine device driver node
3. display devices
- DECON, DSI and MIC for the panel output
4. USB devices
- USB 3.0 DRD (Dual Role Device)
- USB 3.0 Host controller
5. storage devices
- MSHC (Mobile Storage Host Controller) for eMMC device
6. misc devices
- gpio-keys (power, volume up/down, home key)
- PWM (Pulse Width Modulation Timer)
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Ingi kim <ingi2.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable support for on board SPI EEPROM by setting
CONFIG_EEPROM_AT25=m
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The Pine64 is a cost-efficient development board based on the
Allwinner A64 SoC.
There are three models: the basic version with Fast Ethernet and
512 MB of DRAM (Pine64) and two Pine64+ versions, which both
feature Gigabit Ethernet and additional connectors for touchscreens
and a camera. Or as my son put it: "Those are smaller and these are
missing." ;-)
The two Pine64+ models just differ in the amount of DRAM
(1GB vs. 2GB). Since U-Boot will figure out the right size for us and
patches the DT accordingly we just need to provide one DT for the
Pine64+.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Maxime: Removed the common DTSI and include directly the pine64 DTS]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A64 SoC is a low-cost chip with 4 ARM Cortex-A53 cores
and the typical tablet / TV box peripherals.
The SoC is based on the (32-bit) Allwinner H3 chip, sharing most of
the peripherals and the memory map.
Although the cores are proper 64-bit ones, the whole SoC is actually
limited to 4GB (including all the supported DRAM), so we use 32-bit
address and size cells. This has the nice feature of us being able to
reuse the DT for 32-bit kernels as well.
This .dtsi lists the hardware that we support so far.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
[Maxime: Convert to CCU binding, drop the MMC support for now]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a device node for the RST module, which provides a.o. reset control
and mode pin monitoring.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Add a device node for the RST module, which provides a.o. reset control
and mode pin monitoring.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
There is a 'cpu-id' field in efuse, export it for other drivers
reference.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
No need for it - we only use struct bio_vec in prototypes and already have
forward declarations for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The devicetree node for mt8173-auxadc lacks the clock and
io-channel-cells property. This leads to a non-working driver.
mt6577-auxadc 11001000.auxadc: failed to get auxadc clock
mt6577-auxadc: probe of 11001000.auxadc failed with error -2
Fix these fields to get the device up and running.
Fixes: 748c7d4de4 ("ARM64: dts: mt8173: Add thermal/auxadc device
nodes")
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
We haven't seen a whole lot of fixes for the first two weeks since the merge
window, but here is the batch that we have at the moment.
Nothing sticks out as particularly bad or scary, it's mostly a handful of
smaller fixes to several platforms. The Uniphier reset controller changes
could probably have been delayed to 4.10, but they're not scary and just
plumbing up driver changes that went in during the merge window.
We're also adding another maintainer to Marvell Berlin platforms, to help
out when Sebastian is too busy. Yay teamwork!
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OGbj
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We haven't seen a whole lot of fixes for the first two weeks since the
merge window, but here is the batch that we have at the moment.
Nothing sticks out as particularly bad or scary, it's mostly a handful
of smaller fixes to several platforms. The Uniphier reset controller
changes could probably have been delayed to 4.10, but they're not
scary and just plumbing up driver changes that went in during the
merge window.
We're also adding another maintainer to Marvell Berlin platforms, to
help out when Sebastian is too busy. Yay teamwork!"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
ARM: dts: vf610: fix IRQ flag of global timer
ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
ARM: imx: gpc: Initialize all power domains
arm64: dts: Updated NAND DT properties for NS2 SVK
arm64: dts: uniphier: change MIO node to SD control node
ARM: dts: uniphier: change MIO node to SD control node
reset: uniphier: rename MIO reset to SD reset for Pro5, PXs2, LD20 SoCs
arm64: uniphier: select ARCH_HAS_RESET_CONTROLLER
ARM: uniphier: select ARCH_HAS_RESET_CONTROLLER
arm64: dts: Add timer erratum property for LS2080A and LS1043A
arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
ARM: multi_v7_defconfig: Enable Intel e1000e driver
MAINTAINERS: add myself as Marvell berlin SoC maintainer
bus: qcom-ebi2: depend on ARCH_QCOM or COMPILE_TEST
ARM: dts: fix the SD card on the Snowball
arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
arm64: dts: marvell: fix clocksource for CP110 master SPI0
ARM: mvebu: Select corediv clk for all mvebu v7 SoC
1. Addition of SMMU(MMU-401) device nodes mainly to assist other
developments and testing
2. Addition of CPU dmips/capacity information on all the Juno boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PFTb
-----END PGP SIGNATURE-----
Merge tag 'juno-dt-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt64
ARMv8 Vexpress/Juno DT updates for v4.10
1. Addition of SMMU(MMU-401) device nodes mainly to assist other
developments and testing
2. Addition of CPU dmips/capacity information on all the Juno boards
* tag 'juno-dt-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: add cpu capacity-dmips-mhz information to R2 boards
arm64: dts: juno: add cpu capacity-dmips-mhz information to R1 boards
arm64: dts: juno: add cpu capacity-dmips-mhz information to R0 boards
arm64: dts: juno: Add SMMUs device nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
bind/unbind calls work correctly and remove a sdio-only
property from non-sdio mmc hosts, that accidentially was
added there.
-----BEGIN PGP SIGNATURE-----
iQEtBAABCAAXBQJYExViEBxoZWlrb0BzbnRlY2guZGUACgkQ86Z5yZzRHYGwZggA
tK2vjkNsdbFGHscpOxzzMX3ck1tcTgHdFZY/0kgBW6yRm1/FnqP1JW20P2QIthI3
ax1U4m7xDzoS089UndkyHQnHd0ZaUV2htCrocih91QST6Og24atCiyvPSIR58Qbs
EpMNJhbXFVctJarUxdrsCMF0jl2AxxD9euPDhjkYiXLZ0tmdIWZXQUmafmGKviWs
EytssiPPs4fUOOymqKv3kMw2OoTmrTlSNMXpWWDguTPn5p2mDlHOwbJKlgyz8c4x
HAYM56Ad4S0bJyOtraVcPrwfB6gQ321Qs+JfPBR3YJgt1EIjzgeG+W5TYLezXYDu
h1/FnJqU6yrlos+NSIptxQ==
=KA/s
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rockchip-dts64-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Correct regulator handling on Rockchip arm64 boards to make
bind/unbind calls work correctly and remove a sdio-only
property from non-sdio mmc hosts, that accidentially was
added there.
* tag 'v4.9-rockchip-dts64-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
Signed-off-by: Olof Johansson <olof@lixom.net>
- Ray adds the required bus width and OOB sector size properties to the
Northstar 2 SVK reference board in order for the NAND controller to work
properly
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Hfed
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.9/devicetree-arm64-fixes' of http://github.com/Broadcom/stblinux into fixes
This pull request contains a single fix for Broadcom ARM64-based SoCs:
- Ray adds the required bus width and OOB sector size properties to the
Northstar 2 SVK reference board in order for the NAND controller to work
properly
* tag 'arm-soc/for-4.9/devicetree-arm64-fixes' of http://github.com/Broadcom/stblinux:
arm64: dts: Updated NAND DT properties for NS2 SVK
Signed-off-by: Olof Johansson <olof@lixom.net>
- A couple of patches from Fabio to fix the GPC power domain regression
which is caused by PM Domain core change 0159ec6707
("PM / Domains: Verify the PM domain is present when adding a
provider"), and a related kernel crash seen with multi_v7_defconfig
build.
- Correct the PHY ID mask for AR8031 to match phy driver code.
- Apply new added timer erratum A008585 for LS1043A and LS2080A SoC.
- Correct vf610 global timer IRQ flag to avoid warning from gic driver
after commit 992345a58e ("irqchip/gic: WARN if setting the
interrupt type for a PPI fails").
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYDhQ/AAoJEFBXWFqHsHzOjK8H/0BpUb5J1q+ULcJr5boRoErh
LIILJA3q0voOXjONRhOcUx8d3yVccR4AFDsMxP3fzfzDvHrNJcK0ldqMg2I/TvL9
0hUt/IDxSoQ4dCtuuMpWMATeAiUGzCebxKfg12stB+wXUALD7upBrLNP509/Vifw
O8xhPW5w5nWJ5g72QHpDQIqG0Le0Lf4lhuvPsS/hYOeL6mkGVfDTRMOduM3n3KLd
YSMj9NuG1IH9f4xKxGVcs/2ZPdNk+t0PfP/NuPIY3S0qtWwkJRQSPV314WEsxDff
pSCD/KhtkWf8VsHbOgiZUKXPQEsUuKLpqnjjkuF2Sm9KmYCgvaXfLfyX2eyyMN8=
=Xh9e
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 4.9:
- A couple of patches from Fabio to fix the GPC power domain regression
which is caused by PM Domain core change 0159ec6707
("PM / Domains: Verify the PM domain is present when adding a
provider"), and a related kernel crash seen with multi_v7_defconfig
build.
- Correct the PHY ID mask for AR8031 to match phy driver code.
- Apply new added timer erratum A008585 for LS1043A and LS2080A SoC.
- Correct vf610 global timer IRQ flag to avoid warning from gic driver
after commit 992345a58e ("irqchip/gic: WARN if setting the
interrupt type for a PPI fails").
* tag 'imx-fixes-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
ARM: dts: vf610: fix IRQ flag of global timer
ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
ARM: imx: gpc: Initialize all power domains
arm64: dts: Add timer erratum property for LS2080A and LS1043A
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds CONFIG_HIBERNATION to the arm64 defconfig.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add SDHI nodes to the DT of the r8a7796 SoC.
Based on the DT of the r8a7795 SoC.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The SoC-specific compatible strings have been removed from the FCP DT
bindings, removed them from the device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Extend the ARM64 defconfig to enable the DU DRM device as module
together with required dependencies of V4L2 FCP and VSP modules.
This enables VGA output on the r8a7795 Salvator-X board.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fix parameter name for __page_to_voff, to match its definition.
At present, we don't see any issue, as page_to_virt's caller
declares 'page'.
Fixes: 9f2875912d ("arm64: mm: restrict virt_to_page() to the linear mapping")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When booting on NUMA system with memory-less node (no
memory dimm on this memory controller), the print
for setup_node_data() is incorrect:
NUMA: Initmem setup node 2 [mem 0x00000000-0xffffffffffffffff]
It can be fixed by printing [mem 0x00000000-0x00000000] when
end_pfn is 0, but print <memory-less node> will be more useful.
Fixes: 1a2db30034 ("arm64, numa: Add NUMA support for arm64 platforms.")
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ganapatrao Kulkarni <gkulkarni@caviumnetworks.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Its all generic atomic_long_t stuff now.
Tested-by: Jason Low <jason.low2@hpe.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
bcm2837-rpi-3-b.dts, its only in-tree user, was overriding it as
"brcm,bcm2837" already.
Fixes: 9d56c22a78 ("ARM: bcm2835: Add devicetree for the Raspberry Pi 3.")
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch adds pmic specific dts which are configured specially
for db820c. One of such pin is GPIO_F on the Low Speed expansion
which has default output voltage of 2.7v. This patch fixes setup
for that pin to have an output voltage of 1.8v to comply with
96boards LS expansion specs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The Hexagon core on the msm8916 provides services for audio control,
audio output, sensors and the Hexagon SDK. The Hexagon remoteproc node
allows us to boot this core.
Although its part of the core platform its left disabled as it will
crash without the rmtfs QMI service and we do not yet handle crashes
gracefully.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the Hexagon SMD edge, so that QRTR is probed when the Hexagon is
booted.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add clock controller nodes, including one top controller
two low speed controllers and one audio controller.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds NAND DT properties for NS2 SVK to configure the bus
width width and OOB sector size
Signed-off-by: Prafulla Kota <prafulla.kota@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The UniPhier reset driver (drivers/reset/reset-uniphier.c) has been
merged. Select ARCH_HAS_RESET_CONTROLLER from the SoC Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The WnR bit in the HSR/ESR_EL2 indicates whether a data abort was
generated by a read or a write instruction. For stage 2 data aborts
generated by a stage 1 translation table walk (i.e. the actual page
table access faults at EL2), the WnR bit therefore reports whether the
instruction generating the walk was a load or a store, *not* whether the
page table walker was reading or writing the entry.
For page tables marked as read-only at stage 2 (e.g. due to KSM merging
them with the tables from another guest), this could result in livelock,
where a page table walk generated by a load instruction attempts to
set the access flag in the stage 1 descriptor, but fails to trigger
CoW in the host since only a read fault is reported.
This patch modifies the arm64 kvm_vcpu_dabt_iswrite function to
take into account stage 2 faults in stage 1 walks. Since DBM cannot be
disabled at EL2 for CPUs that implement it, we assume that these faults
are always causes by writes, avoiding the livelock situation at the
expense of occasional, spurious CoWs.
We could, in theory, do a bit better by checking the guest TCR
configuration and inspecting the page table to see why the PTE faulted.
However, I doubt this is measurable in practice, and the threat of
livelock is real.
Cc: <stable@vger.kernel.org>
Cc: Julien Grall <julien.grall@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add video decoder node for MT8173
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The LS1046A QorIQ development system (QDS) board is a high-performance
computing, evaluation, development, and test platform supporting the
LS1046A SoC.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LS1046A reference design board (RDB) is a high-performance computing,
evaluation, and development platform that supports the LS1046A SoC.
Signed-off-by: Mingkai Hu <Mingkai.Hu@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
LS1046A is an SoC with 4 ARMv8 A72 cores and most other IP blocks
are similar to LS1043A which also complies to Freescale Chassis 2.1
spec.
Created LS1046A SoC DTSI file to be included by board level DTS
files.
Signed-off-by: Horia Geant? <horia.geanta@nxp.com>
Signed-off-by: Mihai Bantea <mihai.bantea@nxp.com>
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Both the LS1043A and LS2080A platforms are affected by the Freescale
A008585 erratum. Advertise it in their respective device trees.
Signed-off-by: Scott Wood <oss@buserror.net>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Emit the XTS tweak literal constants in the appropriate order for a
single 128-bit scalar literal load.
Fixes: 49788fe2a1 ("arm64/crypto: AES-ECB/CBC/CTR/XTS using ARMv8 NEON and Crypto Extensions")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The AES implementation using pure NEON instructions relies on the generic
AES key schedule generation routines, which store the round keys as arrays
of 32-bit quantities stored in memory using native endianness. This means
we should refer to these round keys using 4x4 loads rather than 16x1 loads.
In addition, the ShiftRows tables are loading using a single scalar load,
which is also affected by endianness, so emit these tables in the correct
order depending on whether we are building for big endian or not.
Fixes: 49788fe2a1 ("arm64/crypto: AES-ECB/CBC/CTR/XTS using ARMv8 NEON and Crypto Extensions")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The AES-CCM implementation that uses ARMv8 Crypto Extensions instructions
refers to the AES round keys as pairs of 64-bit quantities, which causes
failures when building the code for big endian. In addition, it byte swaps
the input counter unconditionally, while this is only required for little
endian builds. So fix both issues.
Fixes: 12ac3efe74 ("arm64/crypto: use crypto instructions to generate AES key schedule")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The SHA256 digest is an array of 8 32-bit quantities, so we should refer
to them as such in order for this code to work correctly when built for
big endian. So replace 16 byte scalar loads and stores with 4x32 vector
ones where appropriate.
Fixes: 6ba6c74dfc ("arm64/crypto: SHA-224/SHA-256 using ARMv8 Crypto Extensions")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The SHA1 digest is an array of 5 32-bit quantities, so we should refer
to them as such in order for this code to work correctly when built for
big endian. So replace 16 byte scalar loads and stores with 4x4 vector
ones where appropriate.
Fixes: 2c98833a42 ("arm64/crypto: SHA-1 using ARMv8 Crypto Extensions")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The GHASH key and digest are both pairs of 64-bit quantities, but the
GHASH code does not always refer to them as such, causing failures when
built for big endian. So replace the 16x1 loads and stores with 2x8 ones.
Fixes: b913a6404c ("arm64/crypto: improve performance of GHASH algorithm")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The core AES cipher implementation that uses ARMv8 Crypto Extensions
instructions erroneously loads the round keys as 64-bit quantities,
which causes the algorithm to fail when built for big endian. In
addition, the key schedule generation routine fails to take endianness
into account as well, when loading the combining the input key with
the round constants. So fix both issues.
Fixes: 12ac3efe74 ("arm64/crypto: use crypto instructions to generate AES key schedule")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This commits adds the devicetree description of the SafeXcel IP-76 TRNG
found in the two Armada CP110.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for eMMC/SD/SDIO on the Nexbox A95x.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add Wifi module support on the Amlogic P20x boards on the SDIO port.
The Wifi module also needs a 32768Hz clock provided by the PWM E port
through a pwm-clock node in it's power sequence.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add a 32768Hz clock generated by the PWM E port used by the WiFi module.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
- Fix ACPI boot due to recent broken NUMA changes
- Fix remote enabling of CPU features requiring PSTATE bit manipulation
- Add address range check when emulating user cache maintenance
- Fix LL/SC loops that allow compiler to introduce memory accesses
- Fix recently added write_sysreg_s macro
- Ensure MDCR_EL2 is initialised on qemu targets without a PMU
- Avoid kaslr breakage due to MODVERSIONs and DYNAMIC_FTRACE
- Correctly drive recent ld when building relocatable Image
- Remove junk IS_ERR check from xgene PMU driver added during merge window
- pr_cont fixes after core changes in the merge window
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJYCNgDAAoJELescNyEwWM0BV8IAKZLVlfKk2YTo3T/tx/2FGIW
5VKjSY13VLLC5cKQLB7Yvm7G1kzvLiN4Zb5fqvL0CK1ut8scPVbR1AAhSDngB4vU
UNzUqwp1R0Tl+GhLT+IfOElWjEcB9kwic3CZV5v4FxvZg4HvwstL3zLvMkjTaDYK
GjaS9iQ2zQsgsYHtluzia7q1k2fXfqdLOd5V0XF05CykJKO3j7zpqTv8PKF7PUFU
utsjRdyyGmBYaamG/cO5phDbAD5VMvdWcfDeJ25JdSwHaoxjZ8tpM721R4b5GRN7
5rPn52v5Hycp++FmhuO45laVQc60LYMz17mQwSTnIX2pGuFRqjRWJztJpyQqzWo=
=MXN1
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Most of these are CC'd for stable, but there are a few fixing issues
introduced during the recent merge window too.
There's also a fix for the xgene PMU driver, but it seemed daft to
send as a separate pull request, so I've included it here with the
rest of the fixes.
- Fix ACPI boot due to recent broken NUMA changes
- Fix remote enabling of CPU features requiring PSTATE bit manipulation
- Add address range check when emulating user cache maintenance
- Fix LL/SC loops that allow compiler to introduce memory accesses
- Fix recently added write_sysreg_s macro
- Ensure MDCR_EL2 is initialised on qemu targets without a PMU
- Avoid kaslr breakage due to MODVERSIONs and DYNAMIC_FTRACE
- Correctly drive recent ld when building relocatable Image
- Remove junk IS_ERR check from xgene PMU driver added during merge window
- pr_cont fixes after core changes in the merge window"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: remove pr_cont abuse from mem_init
arm64: fix show_regs fallout from KERN_CONT changes
arm64: kernel: force ET_DYN ELF type for CONFIG_RELOCATABLE=y
arm64: suspend: Reconfigure PSTATE after resume from idle
arm64: mm: Set PSTATE.PAN from the cpu_enable_pan() call
arm64: cpufeature: Schedule enable() calls instead of calling them via IPI
arm64: Cortex-A53 errata workaround: check for kernel addresses
arm64: percpu: rewrite ll/sc loops in assembly
arm64: swp emulation: bound LL/SC retries before rescheduling
arm64: sysreg: Fix use of XZR in write_sysreg_s
arm64: kaslr: keep modules close to the kernel when DYNAMIC_FTRACE=y
arm64: kernel: Init MDCR_EL2 even in the absence of a PMU
perf: xgene: Remove bogus IS_ERR() check
arm64: kernel: numa: fix ACPI boot cpu numa node mapping
arm64: kaslr: fix breakage with CONFIG_MODVERSIONS=y
Add binding and basic support for the SD/eMMC controller on Amlogic
S905/GXBB devices.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: added nodes for GX, enabled SDIO on P20x]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable MMC related defaults configs for MMC, PWM and PWM clock.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
All the lines printed by mem_init are independent, with each ending with
a newline. While they logically form a large block, none are actually
continuations of previous lines.
The kernel-side printk code and the userspace demsg tool differ in their
handling of KERN_CONT following a newline, and while this isn't always a
problem kernel-side, it does cause difficulty for userspace. Using
pr_cont causes the userspace tool to not print line prefix (e.g.
timestamps) even when following a newline, mis-aligning the output and
making it harder to read, e.g.
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] modules : 0xffff000000000000 - 0xffff000008000000 ( 128 MB)
vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000 (129022 GB)
.text : 0xffff000008080000 - 0xffff0000088b0000 ( 8384 KB)
.rodata : 0xffff0000088b0000 - 0xffff000008c50000 ( 3712 KB)
.init : 0xffff000008c50000 - 0xffff000008d50000 ( 1024 KB)
.data : 0xffff000008d50000 - 0xffff000008e25200 ( 853 KB)
.bss : 0xffff000008e25200 - 0xffff000008e6bec0 ( 284 KB)
fixed : 0xffff7dfffe7fd000 - 0xffff7dfffec00000 ( 4108 KB)
PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000 ( 16 MB)
vmemmap : 0xffff7e0000000000 - 0xffff800000000000 ( 2048 GB maximum)
0xffff7e0000000000 - 0xffff7e0026000000 ( 608 MB actual)
memory : 0xffff800000000000 - 0xffff800980000000 ( 38912 MB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
Fix this by using pr_notice consistently for all lines, which both the
kernel and userspace are happy with.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Recently in commit 4bcc595ccd ("printk: reinstate KERN_CONT for
printing continuation lines"), the behaviour of printk changed w.r.t.
KERN_CONT. Now, KERN_CONT is mandatory to continue existing lines.
Without this, prefixes are inserted, making output illegible, e.g.
[ 1007.069010] pc : [<ffff00000871898c>] lr : [<ffff000008718948>] pstate: 40000145
[ 1007.076329] sp : ffff000008d53ec0
[ 1007.079606] x29: ffff000008d53ec0 [ 1007.082797] x28: 0000000080c50018
[ 1007.086160]
[ 1007.087630] x27: ffff000008e0c7f8 [ 1007.090820] x26: ffff80097631ca00
[ 1007.094183]
[ 1007.095653] x25: 0000000000000001 [ 1007.098843] x24: 000000ea68b61cac
[ 1007.102206]
... or when dumped with the userpace dmesg tool, which has slightly
different implicit newline behaviour. e.g.
[ 1007.069010] pc : [<ffff00000871898c>] lr : [<ffff000008718948>] pstate: 40000145
[ 1007.076329] sp : ffff000008d53ec0
[ 1007.079606] x29: ffff000008d53ec0
[ 1007.082797] x28: 0000000080c50018
[ 1007.086160]
[ 1007.087630] x27: ffff000008e0c7f8
[ 1007.090820] x26: ffff80097631ca00
[ 1007.094183]
[ 1007.095653] x25: 0000000000000001
[ 1007.098843] x24: 000000ea68b61cac
[ 1007.102206]
We can't simply always use KERN_CONT for lines which may or may not be
continuations. That causes line prefixes (e.g. timestamps) to be
supressed, and the alignment of all but the first line will be broken.
For even more fun, we can't simply insert some dummy empty-string printk
calls, as GCC warns for an empty printk string, and even if we pass
KERN_DEFAULT explcitly to silence the warning, the prefix gets swallowed
unless there is an additional part to the string.
Instead, we must manually iterate over pairs of registers, which gives
us the legible output we want in either case, e.g.
[ 169.771790] pc : [<ffff00000871898c>] lr : [<ffff000008718948>] pstate: 40000145
[ 169.779109] sp : ffff000008d53ec0
[ 169.782386] x29: ffff000008d53ec0 x28: 0000000080c50018
[ 169.787650] x27: ffff000008e0c7f8 x26: ffff80097631de00
[ 169.792913] x25: 0000000000000001 x24: 00000027827b2cf4
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
GNU ld used to set the ELF file type to ET_DYN for PIE executables, which
is the same file type used for shared libraries. However, this was changed
recently, and now PIE executables are emitted as ET_EXEC instead.
The distinction is only relevant for ELF loaders, and so there is little
reason to care about the difference when building the kernel, which is
why the change has gone unnoticed until now.
However, debuggers do use the ELF binary, and expect ET_EXEC type files
to appear in memory at the exact offset described in the ELF metadata.
This means source level debugging is no longer possible when KASLR is in
effect or when executing the stub.
So add the -shared LD option when building with CONFIG_RELOCATABLE=y. This
forces the ELF file type to be set to ET_DYN (which is what you get when
building with binutils 2.24 and earlier anyway), and has no other ill
effects.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The suspend/resume path in kernel/sleep.S, as used by cpu-idle, does not
save/restore PSTATE. As a result of this cpufeatures that were detected
and have bits in PSTATE get lost when we resume from idle.
UAO gets set appropriately on the next context switch. PAN will be
re-enabled next time we return from user-space, but on a preemptible
kernel we may run work accessing user space before this point.
Add code to re-enable theses two features in __cpu_suspend_exit().
We re-use uao_thread_switch() passing current.
Signed-off-by: James Morse <james.morse@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 338d4f49d6 ("arm64: kernel: Add support for Privileged Access
Never") enabled PAN by enabling the 'SPAN' feature-bit in SCTLR_EL1.
This means the PSTATE.PAN bit won't be set until the next return to the
kernel from userspace. On a preemptible kernel we may schedule work that
accesses userspace on a CPU before it has done this.
Now that cpufeature enable() calls are scheduled via stop_machine(), we
can set PSTATE.PAN from the cpu_enable_pan() call.
Add WARN_ON_ONCE(in_interrupt()) to check the PSTATE value we updated
is not immediately discarded.
Reported-by: Tony Thompson <anthony.thompson@arm.com>
Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
[will: fixed typo in comment]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The enable() call for a cpufeature/errata is called using on_each_cpu().
This issues a cross-call IPI to get the work done. Implicitly, this
stashes the running PSTATE in SPSR when the CPU receives the IPI, and
restores it when we return. This means an enable() call can never modify
PSTATE.
To allow PAN to do this, change the on_each_cpu() call to use
stop_machine(). This schedules the work on each CPU which allows
us to modify PSTATE.
This involves changing the protype of all the enable() functions.
enable_cpu_capabilities() is called during boot and enables the feature
on all online CPUs. This path now uses stop_machine(). CPU features for
hotplug'd CPUs are enabled by verify_local_cpu_features() which only
acts on the local CPU, and can already modify the running PSTATE as it
is called from secondary_start_kernel().
Reported-by: Tony Thompson <anthony.thompson@arm.com>
Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 7dd01aef05 ("arm64: trap userspace "dc cvau" cache operation on
errata-affected core") adds code to execute cache maintenance instructions
in the kernel on behalf of userland on CPUs with certain ARM CPU errata.
It turns out that the address hasn't been checked to be a valid user
space address, allowing userland to clean cache lines in kernel space.
Fix this by introducing an address check before executing the
instructions on behalf of userland.
Since the address doesn't come via a syscall parameter, we can't just
reject tagged pointers and instead have to remove the tag when checking
against the user address limit.
Cc: <stable@vger.kernel.org>
Fixes: 7dd01aef05 ("arm64: trap userspace "dc cvau" cache operation on errata-affected core")
Reported-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[will: rework commit message + replace access_ok with max_user_addr()]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Writing the outer loop of an LL/SC sequence using do {...} while
constructs potentially allows the compiler to hoist memory accesses
between the STXR and the branch back to the LDXR. On CPUs that do not
guarantee forward progress of LL/SC loops when faced with memory
accesses to the same ERG (up to 2k) between the failed STXR and the
branch back, we may end up livelocking.
This patch avoids this issue in our percpu atomics by rewriting the
outer loop as part of the LL/SC inline assembly block.
Cc: <stable@vger.kernel.org>
Fixes: f97fc81079 ("arm64: percpu: Implement this_cpu operations")
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
If a CPU does not implement a global monitor for certain memory types,
then userspace can attempt a kernel DoS by issuing SWP instructions
targetting the problematic memory (for example, a framebuffer mapped
with non-cacheable attributes).
The SWP emulation code protects against these sorts of attacks by
checking for pending signals and potentially rescheduling when the STXR
instruction fails during the emulation. Whilst this is good for avoiding
livelock, it harms emulation of legitimate SWP instructions on CPUs
where forward progress is not guaranteed if there are memory accesses to
the same reservation granule (up to 2k) between the failing STXR and
the retry of the LDXR.
This patch solves the problem by retrying the STXR a bounded number of
times (4) before breaking out of the LL/SC loop and looking for
something else to do.
Cc: <stable@vger.kernel.org>
Fixes: bd35a4adc4 ("arm64: Port SWP/SWPB emulation support from arm")
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Most of the drivers are included as modules, except for serial (needed
for early console), WDT (required for reboot), and the dependency
chain of RASPBERRYPI_POWER (which is currently not buildable as a
module, but should be changed).
Signed-off-by: Eric Anholt <eric@anholt.net>
With the "mmu-masters" property now deprecated and optional, the
generic binding offers a more efficient way to specify no masters.
CC: Ray Jui <rjui@broadcom.com>
CC: Scott Branden <sbranden@broadcom.com>
CC: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch adds NAND DT properties for NS2 SVK to configure the bus
width width and OOB sector size
Signed-off-by: Prafulla Kota <prafulla.kota@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Adding QSPI node compatible with the new spi-bcm-qspi driver for the Broadcom's
Northstar2 SoC.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It was invented for sdio only, and should not be used for sdmmc
or emmc. Remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable both gxbb USB controller and add a 5V regulator for the OTG port
VBUS
Signed-off-by: Brian Kim <brian.kim@hardkernel.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
For boards only supporting 10/100 ethernet over a RMII PHY link, add
a separate pinctrl node. By the way, rename the existing node to rgmii
specific naming in all boards dts.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
In order to remove the boot warning :
[ 2.290933] Unable to detect cache hierarchy from DT for CPU 0
And add missing L2 cache hierarchy information, add a simple l2 cache node
and reference it from the A53 cpu nodes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add support for the S905 (GXBB) version of the Nexbox A95X.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch introduces the basic support for the Amlogic S905D (MesonGXL)
and for the Amlogic evaluation boards P230 and P231.
No documentation has been released yet for this SoC, so for now only the
bare minimum has been added in the DT.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch introduces the basic support for the Amlogic S905X (Meson
GXL) and for the Amlogic evaluation board P212.
No documentation has been released yet for this SoC, so for now only the
bare minimum has been added in the DT.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Move all non-gxbb specific nodes to a common GX dtsi.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
- Select corediv clk for all mvebu v7 SoC
- Fix clocksource for CP110 master SPI0 for Armada 7K/8K
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlfhYDEACgkQCwYYjhRyO9XaBwCdGJp7xh21bQtg8wX1ROmX/430
EGIAoKzEXjU3SNJL1fEghsMJLarsvVaq
=D3Mt
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.8-3' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 4.8 (part 3)
- Select corediv clk for all mvebu v7 SoC
- Fix clocksource for CP110 master SPI0 for Armada 7K/8K
* tag 'mvebu-fixes-4.8-3' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: fix clocksource for CP110 master SPI0
ARM: mvebu: Select corediv clk for all mvebu v7 SoC
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 8a71f0c656 ("arm64: sysreg: replace open-coded mrs_s/msr_s with
{read,write}_sysreg_s") introduced a write_sysreg_s macro for writing
to system registers that are not supported by binutils.
Unfortunately, this was implemented with the wrong template (%0 vs %x0),
so in the case that we are writing a constant 0, we will generate
invalid instruction syntax and bail with a cryptic assembler error:
| Error: constant expression required
This patch fixes the template.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In case dr_mode isn't passed via DT, the dwc2 driver defaults
to OTG mode. But the Raspberry Pi 3 is designed only for host mode.
So fix this issue by linking to the dtsi file which set the dr_mode
to host.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Juno has separate MMU-401 instances in front of the DMA-330, both HDLCD
controllers, the USB host controller, the PCIe root complex, and the
CoreSight ETR. Since there is still work to do to make all the relevant
subsystems interact nicely with the presence of an IOMMU, add the nodes
to aid development and testing but leave them disabled by default to
avoid nasty surprises.
CC: Liviu Dudau <liviu.dudau@arm.com>
CC: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
[sudeep.holla@arm.com: reformated subject]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The RANDOMIZE_MODULE_REGION_FULL Kconfig option allows KASLR to be
configured in such a way that kernel modules and the core kernel are
allocated completely independently, which implies that modules are likely
to require branches via PLT entries to reach the core kernel. The dynamic
ftrace code does not expect that, and assumes that it can patch module
code to perform a relative branch to anywhere in the core kernel. This
may result in errors such as
branch_imm_common: offset out of range
------------[ cut here ]------------
WARNING: CPU: 3 PID: 196 at kernel/trace/ftrace.c:1995 ftrace_bug+0x220/0x2e8
Modules linked in:
CPU: 3 PID: 196 Comm: systemd-udevd Not tainted 4.8.0-22-generic #24
Hardware name: AMD Seattle/Seattle, BIOS 10:34:40 Oct 6 2016
task: ffff8d1bef7dde80 task.stack: ffff8d1bef6b0000
PC is at ftrace_bug+0x220/0x2e8
LR is at ftrace_process_locs+0x330/0x430
So make RANDOMIZE_MODULE_REGION_FULL mutually exclusive with DYNAMIC_FTRACE
at the Kconfig level.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This is a high performance 64 bit dual core low power consuming
networking computing platform based on the ARMv8 architecture.
It contains an Armada 3720 running up to 1.2Ghz.
This commit adds a basic definition for this board.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Commit f436b2ac90 ("arm64: kernel: fix architected PMU registers
unconditional access") made sure we wouldn't access unimplemented
PMU registers, but also left MDCR_EL2 uninitialized in that case,
leading to trap bits being potentially left set.
Make sure we always write something in that register.
Fixes: f436b2ac90 ("arm64: kernel: fix architected PMU registers unconditional access")
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 7ba5f605f3 ("arm64/numa: remove the limitation that cpu0 must
bind to node0") removed the numa cpu<->node mapping restriction whereby
logical cpu 0 always corresponds to numa node 0; removing the
restriction was correct, in that it does not really exist in practice
but the commit only updated the early mapping of logical cpu 0 to its
real numa node for the DT boot path, missing the ACPI one, leading to
boot failures on ACPI systems owing to missing node<->cpu map for
logical cpu 0.
Fix the issue by updating the ACPI boot path with code that carries out
the early cpu<->node mapping also for the boot cpu (ie cpu 0), mirroring
what is currently done in the DT boot path.
Fixes: 7ba5f605f3 ("arm64/numa: remove the limitation that cpu0 must bind to node0")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Reported-by: Laszlo Ersek <lersek@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Andrew Jones <drjones@redhat.com>
Cc: Zhen Lei <thunder.leizhen@huawei.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
As it turns out, the KASLR code breaks CONFIG_MODVERSIONS, since the
kcrctab has an absolute address field that is relocated at runtime
when the kernel offset is randomized.
This has been fixed already for PowerPC in the past, so simply wire up
the existing code dealing with this issue.
Cc: <stable@vger.kernel.org>
Fixes: f80fb3a3d5 ("arm64: add support for kernel ASLR")
Tested-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Declaring the endpoint makes LVDS enablement easier by just including
the corresponding panel's dtsi file.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
It can be used for the watchdog.
Based on similar work for r8a7795/salvator-x by Wolfram Sang.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
px5-evb has one sdmmc slot, so we could support sdmmc.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The emmc on px5-evb can support hs200, so let's add mmc-hs200-1_8v.
And in order to speed up the boot time, we could add no-sdio and
no-sd to simplify the initialization.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
PX5 EVB is designed by Rockchip for automotive field
with integrated CVBS (TP2825) / MIPI DSI / CSI / LVDS
HDMI video input/output interface, audio codec ES8396,
WIFI/BT (on RTL8723BS), Gsensor BMA250E and light&proximity
sensor STK3410.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The tcpc power domain will try to power up/down the power of Type-C PHY.
Hence, we need control it in Type-C PHY driver with the pm_runtime helper.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
According to the TRM and downstream code from rockchip, the register
address of i2c1 on rk3368 is 0xff660000 and i2c2 is 0xff140000.
This patch fix the i2c1 & i2c2 register address definition error, also
fix the clk and pinctrl reference error.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Please don't add these for vcc_sd, and mmc-core/driver will control
it. Otherwise, it will waste energy even without sdmmc in slot.
Moreover, it will causes a bug:
If we insert/remove sd card, we could see
[9.337271] mmc0: new ultra high speed SDR25 SDHC card at address 0007
[9.345144] mmcblk0: mmc0:0007 SD32G 29.3 GiB
This is okay for normal sd insert/remove test, but when I debug some
issues for sdmmc, I did unbind/bind test. And there is a interesting
phenomenon when we bind the driver again:
[58.314069] mmc0: new high speed SDHC card at address 0007
[58.320282] mmcblk0: mmc0:0007 SD32G 29.3 GiB
So the sd card could just support high speed without power cycle
since the vcc_sd is always on, which makes the sd card fail to
reinit its internal ocr mask.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull more misc uaccess and vfs updates from Al Viro:
"The rest of the stuff from -next (more uaccess work) + assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
score: traps: Add missing include file to fix build error
fs/super.c: don't fool lockdep in freeze_super() and thaw_super() paths
fs/super.c: fix race between freeze_super() and thaw_super()
overlayfs: Fix setting IOP_XATTR flag
iov_iter: kernel-doc import_iovec() and rw_copy_check_uvector()
blackfin: no access_ok() for __copy_{to,from}_user()
arm64: don't zero in __copy_from_user{,_inatomic}
arm: don't zero in __copy_from_user_inatomic()/__copy_from_user()
arc: don't leak bits of kernel stack into coredump
alpha: get rid of tail-zeroing in __copy_user()
Pull libata updates from Tejun Heo:
- Write same support added
- Minor ahci MSIX irq handling updates
- Non-critical SCSI command translation fixes
- Controller specific changes
* 'for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: qoriq: Revert "ahci: qoriq: Disable NCQ on ls2080a SoC"
libata: remove <asm-generic/libata-portmap.h>
libata: remove unused definitions from <asm/libata-portmap.h>
pata_at91: Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
ata: Replace BUG() with BUG_ON().
ata: sata_mv: Replacing dma_pool_alloc and memset with a single call dma_pool_zalloc.
libata: Some drives failing on SCT Write Same
ahci: use pci_alloc_irq_vectors
libata: SCT Write Same handle ATA_DFLAG_PIO
libata: SCT Write Same / DSM Trim
libata: Add support for SCT Write Same
libata: Safely overwrite attached page in WRITE SAME xlat
ahci: also use a per-port lock for the multi-MSIX case
ARM: dts: STiH407-family: Add ports-implemented property in sata nodes
ahci: st: Add ports-implemented property in support
ahci: qoriq: enable snoopable sata read and write
ahci: qoriq: adjust sata parameter
libata-scsi: fix MODE SELECT translation for Control mode page
libata-scsi: use u8 array to store mode page copy
Pull thermal managament updates from Zhang Rui:
- Enhance thermal "userspace" governor to export the reason when a
thermal event is triggered and delivered to user space. From Srinivas
Pandruvada
- Introduce a single TSENS thermal driver for the different versions of
the TSENS IP that exist, on different qcom msm/apq SoCs'. Support for
msm8916, msm8960, msm8974 and msm8996 families is also added. From
Rajendra Nayak
- Introduce hardware-tracked trip points support to the device tree
thermal sensor framework. The framework supports an arbitrary number
of trip points. Whenever the current temperature is changed, the trip
points immediately below and above the current temperature are found,
driver callback is invoked to program the hardware to get notified
when either of the two trip points are triggered. Hardware-tracked
trip points support for rockchip thermal driver is also added at the
same time. From Sascha Hauer, Caesar Wang
- Introduce a new thermal driver, which enables TMU (Thermal Monitor
Unit) on QorIQ platform. From Jia Hongtao
- Introduce a new thermal driver for Maxim MAX77620. From Laxman
Dewangan
- Introduce a new thermal driver for Intel platforms using WhiskeyCove
PMIC. From Bin Gao
- Add mt2701 chip support to MTK thermal driver. From Dawei Chien
- Enhance Tegra thermal driver to enable soctherm node and set
"critical", "hot" trips, for Tegra124, Tegra132, Tegra210. From Wei
Ni
- Add resume support for tango thermal driver. From Marc Gonzalez
- several small fixes and improvements for rockchip, qcom, imx, rcar,
mtk thermal drivers and thermal core code. From Caesar Wang, Keerthy,
Rocky Hao, Wei Yongjun, Peter Robinson, Bui Duc Phuc, Axel Lin, Hugh
Kang
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (48 commits)
thermal: int3403: Process trip change notification
thermal: int340x: New Interface to read trip and notify
thermal: user_space gov: Add additional information in uevent
thermal: Enhance thermal_zone_device_update for events
arm64: tegra: set hot trips for Tegra210
arm64: tegra: set critical trips for Tegra210
arm64: tegra: add soctherm node for Tegra210
arm64: tegra: set hot trips for Tegra132
arm64: tegra: set critical trips for Tegra132
arm64: tegra: use tegra132-soctherm for Tegra132
arm: tegra: set hot trips for Tegra124
arm: tegra: set critical trips for Tegra124
thermal: tegra: add hw-throttle for Tegra132
thermal: tegra: add hw-throttle function
of: Add bindings of hw throttle for Tegra soctherm
thermal: mtk_thermal: Check return value of devm_thermal_zone_of_sensor_register
thermal: Add Mediatek thermal driver for mt2701.
dt-bindings: thermal: Add binding document for Mediatek thermal controller
thermal: max77620: Add thermal driver for reporting junction temp
thermal: max77620: Add DT binding doc for thermal driver
...
Enable CONFIG_GPIO_XGENE_SB.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge more updates from Andrew Morton:
- a few block updates that fell in my lap
- lib/ updates
- checkpatch
- autofs
- ipc
- a ton of misc other things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (100 commits)
mm: split gfp_mask and mapping flags into separate fields
fs: use mapping_set_error instead of opencoded set_bit
treewide: remove redundant #include <linux/kconfig.h>
hung_task: allow hung_task_panic when hung_task_warnings is 0
kthread: add kerneldoc for kthread_create()
kthread: better support freezable kthread workers
kthread: allow to modify delayed kthread work
kthread: allow to cancel kthread work
kthread: initial support for delayed kthread work
kthread: detect when a kthread work is used by more workers
kthread: add kthread_destroy_worker()
kthread: add kthread_create_worker*()
kthread: allow to call __kthread_create_on_node() with va_list args
kthread/smpboot: do not park in kthread_create_on_cpu()
kthread: kthread worker API cleanup
kthread: rename probe_kthread_data() to kthread_probe_data()
scripts/tags.sh: enable code completion in VIM
mm: kmemleak: avoid using __va() on addresses that don't have a lowmem mapping
kdump, vmcoreinfo: report memory sections virtual addresses
ipc/sem.c: add cond_resched in exit_sme
...
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, all callers to randomize_range() set the length to 0 and
calculate end by adding a constant to the start address. We can simplify
the API to remove a bunch of needless checks and variables.
Use the new randomize_addr(start, range) call to set the requested
address.
Link: http://lkml.kernel.org/r/20160803233913.32511-5-jason@lakedaemon.net
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: "Russell King - ARM Linux" <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Including:
* Support for interrupt virtualization in the AMD IOMMU driver.
These patches were shared with the KVM tree and are already
merged through that tree.
* Generic DT-binding support for the ARM-SMMU driver. With this
the driver now makes use of the generic DMA-API code. This
also required some changes outside of the IOMMU code, but
these are acked by the respective maintainers.
* More cleanups and fixes all over the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=1hFE
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- support for interrupt virtualization in the AMD IOMMU driver. These
patches were shared with the KVM tree and are already merged through
that tree.
- generic DT-binding support for the ARM-SMMU driver. With this the
driver now makes use of the generic DMA-API code. This also required
some changes outside of the IOMMU code, but these are acked by the
respective maintainers.
- more cleanups and fixes all over the place.
* tag 'iommu-updates-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (40 commits)
iommu/amd: No need to wait iommu completion if no dte irq entry change
iommu/amd: Free domain id when free a domain of struct dma_ops_domain
iommu/amd: Use standard bitmap operation to set bitmap
iommu/amd: Clean up the cmpxchg64 invocation
iommu/io-pgtable-arm: Check for v7s-incapable systems
iommu/dma: Avoid PCI host bridge windows
iommu/dma: Add support for mapping MSIs
iommu/arm-smmu: Set domain geometry
iommu/arm-smmu: Wire up generic configuration support
Docs: dt: document ARM SMMU generic binding usage
iommu/arm-smmu: Convert to iommu_fwspec
iommu/arm-smmu: Intelligent SMR allocation
iommu/arm-smmu: Add a stream map entry iterator
iommu/arm-smmu: Streamline SMMU data lookups
iommu/arm-smmu: Refactor mmu-masters handling
iommu/arm-smmu: Keep track of S2CR state
iommu/arm-smmu: Consolidate stream map entry state
iommu/arm-smmu: Handle stream IDs more dynamically
iommu/arm-smmu: Set PRIVCFG in stage 1 STEs
iommu/arm-smmu: Support non-PCI devices with SMMUv3
...
Merge updates from Andrew Morton:
- fsnotify updates
- ocfs2 updates
- all of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (127 commits)
console: don't prefer first registered if DT specifies stdout-path
cred: simpler, 1D supplementary groups
CREDITS: update Pavel's information, add GPG key, remove snail mail address
mailmap: add Johan Hovold
.gitattributes: set git diff driver for C source code files
uprobes: remove function declarations from arch/{mips,s390}
spelling.txt: "modeled" is spelt correctly
nmi_backtrace: generate one-line reports for idle cpus
arch/tile: adopt the new nmi_backtrace framework
nmi_backtrace: do a local dump_stack() instead of a self-NMI
nmi_backtrace: add more trigger_*_cpu_backtrace() methods
min/max: remove sparse warnings when they're nested
Documentation/filesystems/proc.txt: add more description for maps/smaps
mm, proc: fix region lost in /proc/self/smaps
proc: fix timerslack_ns CAP_SYS_NICE check when adjusting self
proc: add LSM hook checks to /proc/<tid>/timerslack_ns
proc: relax /proc/<tid>/timerslack_ns capability requirements
meminfo: break apart a very long seq_printf with #ifdefs
seq/proc: modify seq_put_decimal_[u]ll to take a const char *, not char
proc: faster /proc/*/status
...
These updates have been kept in a separate branch mostly because
they rely on updates to the respective clk drivers to keep the
shared header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been
merged for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and
usb driver changes are required and included here, and also
the clk tree changes.
- The Allwinner platforms have seen a large-scale change to their
clk drivers and the dts file updates must come after that.
This includes the newly added Nextthing GR8 platform, which is
derived from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't
added until just before the merge window
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OmAu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been merged
for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and usb
driver changes are required and included here, and also the clk
tree changes.
- The Allwinner platforms have seen a large-scale change to their clk
drivers and the dts file updates must come after that. This
includes the newly added Nextthing GR8 platform, which is derived
from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't added
until just before the merge window"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
ARM: dts: lpc32xx: add device node for IRAM on-chip memory
ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
ARM: dts: sun8i: add pinmux for UART1 at PG
dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
dts: sun8i-h3: add pinmux definitions for I2C0-2
dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
dts: sun8i-h3: add pinmux definitions for UART2-3
ARM: dts: sun9i: a80-optimus: Disable EHCI1
ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
...
The 64-bit DT changes are surprisingly small this time, we only add two
SoC platforms: the ZTE ZX296718 Set-top-box SoC and the SocioNext
UniPhier LD11 TV SoC, each with their reference boards.
There are three new machines added for existing SoC platforms:
- The Marvell Armada 8040 development board is an impressive quad-core
Cortex-A72 machine with three 10gbit ethernet interfaces
- Qualcomms DragonBoard 820c single-board computer is their current
high-end phone platform in the 96boards form factor
- Rockchip: Tronsmart Orion r86 set-top-box is a popular mid-range
Android box based on the 8-core rk3368 SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PxJN
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"The 64-bit DT changes are surprisingly small this time, we only add
two SoC platforms: the ZTE ZX296718 Set-top-box SoC and the SocioNext
UniPhier LD11 TV SoC, each with their reference boards.
There are three new machines added for existing SoC platforms:
- The Marvell Armada 8040 development board is an impressive
quad-core Cortex-A72 machine with three 10gbit ethernet interfaces
- Qualcomms DragonBoard 820c single-board computer is their current
high-end phone platform in the 96boards form factor
- Rockchip: Tronsmart Orion r86 set-top-box is a popular mid-range
Android box based on the 8-core rk3368 SoC"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (91 commits)
arm64: dts: berlin4ct: Add L2 cache topology
arm64: dts: berlin4ct: enable all wdt nodes unconditionally
arm64: dts: berlin4ct: switch to Cortex-A53 specific pmu nodes
arm64: dts: Add ZTE ZX296718 SoC dts and Makefile
arm64: dts: apm: Add DT node for APM X-Gene 2 CPU clocks
arm64: dts: apm: Add X-Gene SoC hwmon to device tree
arm64: dts: apm: Fix interrupt polarity for X-Gene PCIe legacy interrupts
arm64: dts: apm: Add APM X-Gene v2 SoC PMU DTS entries
arm64: dts: apm: Add APM X-Gene SoC PMU DTS entries
arm64: dts: marvell: enable MSI for PCIe on Armada 7K/8K
arm64: dts: ls2080a: Add 'dma-coherent' for ls2080a PCI nodes
arm64: dts: rockchip: add Type-C phy for RK3399
arm64: dts: rockchip: enable the gmac for rk3399 evb board
arm64: dts: rockchip: add the gmac needed node for rk3399
arm64: dts: rockchip: support the pmu node for rk3399
arm64: dts: rockchip: change all interrupts cells to 4 on rk3399 SoCs
arm64: dts: rockchip: add the tcpc for rk3399 power domain
arm64: dts: rockchip: add efuse0 device node for rk3399
arm64: dts: rockchip: configure PCIe support for rk3399-evb
arm64: dts: rockchip: add the PCIe controller support for RK3399
...
Changes to platform code for 64-bit ARM platforms.
Nearly all of these are defconfig updates to enable new drivers or old
drivers still used on these 64-bit platforms.
Aside from that, we gain initial support for two set-top-box platforms,
both of which already have 32-bit support in arch/arm:
- Broadcom adds abstract support for the bcm7xxx/brcmstb platform,
presumably the respective dts files and more information will
follow at a later point.
- The ZTE ZX296718 SoC for set-top-boxes, a relative of the 32-bit
ZX296702 SoC that we already support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5Whi
-----END PGP SIGNATURE-----
Merge tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC 64-bit updates from Arnd Bergmann:
"Changes to platform code for 64-bit ARM platforms.
Nearly all of these are defconfig updates to enable new drivers or old
drivers still used on these 64-bit platforms.
Aside from that, we gain initial support for two set-top-box
platforms, both of which already have 32-bit support in arch/arm:
- Broadcom adds abstract support for the bcm7xxx/brcmstb platform,
presumably the respective dts files and more information will
follow at a later point.
- The ZTE ZX296718 SoC for set-top-boxes, a relative of the 32-bit
ZX296702 SoC that we already support"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: add ZTE ZX SoC family
arm64: defconfig: enable ZTE ZX related config
arm64: defconfig: enable common modules for power management
arm64: defconfig: enable meson I2C
arm64: defconfig: enable meson SPI as module
arm64: defconfig: enable meson WDT as modules
arm64: defconfig: enable HW random as module
arm64: defconfig: Enable SDHI and GPIO_REGULATOR
arm64: configs: enable PCIe driver for Aardvark
Kconfig: ARCH_HISI: Add PINCTRL to HISI platform
arm64: defconfig: enable bluetooth supports as modules
arm64: defconfig: enable CONFIG_INPUT_HISI_POWERKEY for HiKey
arm64: defconfig: Enable HiSilicon kirin drm, adv7533 for HiKey
arm64: defconfig: Enable Hisi SAS and HNS
arm64: defconfig: Enable QDF2432 config options
arm64: sunxi: Kconfig: add essential pinctrl driver
arm64: defconfig: Add Renesas R-Car HSUSB driver support as module
arm64: Add Broadcom Set Top Box Kconfig entry point
arm64: defconfig: enable xhci-platform
When doing an nmi backtrace of many cores, most of which are idle, the
output is a little overwhelming and very uninformative. Suppress
messages for cpus that are idling when they are interrupted and just
emit one line, "NMI backtrace for N skipped: idling at pc 0xNNN".
We do this by grouping all the cpuidle code together into a new
.cpuidle.text section, and then checking the address of the interrupted
PC to see if it lies within that section.
This commit suitably tags x86 and tile idle routines, and only adds in
the minimal framework for other architectures.
Link: http://lkml.kernel.org/r/1472487169-14923-5-git-send-email-cmetcalf@mellanox.com
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org> [arm]
Tested-by: Petr Mladek <pmladek@suse.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This came to light when implementing native 64-bit atomics for ARCv2.
The atomic64 self-test code uses CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE
to check whether atomic64_dec_if_positive() is available. It seems it
was needed when not every arch defined it. However as of current code
the Kconfig option seems needless
- for CONFIG_GENERIC_ATOMIC64 it is auto-enabled in lib/Kconfig and a
generic definition of API is present lib/atomic64.c
- arches with native 64-bit atomics select it in arch/*/Kconfig and
define the API in their headers
So I see no point in keeping the Kconfig option
Compile tested for:
- blackfin (CONFIG_GENERIC_ATOMIC64)
- x86 (!CONFIG_GENERIC_ATOMIC64)
- ia64
Link: http://lkml.kernel.org/r/1473703083-8625-3-git-send-email-vgupta@synopsys.com
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Zhaoxiu Zeng <zhaoxiu.zeng@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Ming Lin <ming.l@ssi.samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arm64 supports gigantic pages after commit 084bd29810 ("ARM64: mm:
HugeTLB support.") however, it can only be allocated at boottime and
can't be freed.
This patch selects ARCH_HAS_GIGANTIC_PAGE to make gigantic pages can be
allocated and freed at runtime for arch arm64.
Link: http://lkml.kernel.org/r/1475227569-63446-3-git-send-email-xieyisheng1@huawei.com
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All architectures:
Move `make kvmconfig` stubs from x86; use 64 bits for debugfs stats.
ARM:
Important fixes for not using an in-kernel irqchip; handle SError
exceptions and present them to guests if appropriate; proxying of GICV
access at EL2 if guest mappings are unsafe; GICv3 on AArch32 on ARMv8;
preparations for GICv3 save/restore, including ABI docs; cleanups and
a bit of optimizations.
MIPS:
A couple of fixes in preparation for supporting MIPS EVA host kernels;
MIPS SMP host & TLB invalidation fixes.
PPC:
Fix the bug which caused guests to falsely report lockups; other minor
fixes; a small optimization.
s390:
Lazy enablement of runtime instrumentation; up to 255 CPUs for nested
guests; rework of machine check deliver; cleanups and fixes.
x86:
IOMMU part of AMD's AVIC for vmexit-less interrupt delivery; Hyper-V
TSC page; per-vcpu tsc_offset in debugfs; accelerated INS/OUTS in
nVMX; cleanups and fixes.
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJX9iDrAAoJEED/6hsPKofoOPoIAIUlgojkb9l2l1XVDgsXdgQL
sRVhYSVv7/c8sk9vFImrD5ElOPZd+CEAIqFOu45+NM3cNi7gxip9yftUVs7wI5aC
eDZRWm1E4trDZLe54ZM9ThcqZzZZiELVGMfR1+ZndUycybwyWzafpXYsYyaXp3BW
hyHM3qVkoWO3dxBWFwHIoO/AUJrWYkRHEByKyvlC6KPxSdBPSa5c1AQwMCoE0Mo4
K/xUj4gBn9eMelNhg4Oqu/uh49/q+dtdoP2C+sVM8bSdquD+PmIeOhPFIcuGbGFI
B+oRpUhIuntN39gz8wInJ4/GRSeTuR2faNPxMn4E1i1u4LiuJvipcsOjPfe0a18=
=fZRB
-----END PGP SIGNATURE-----
Merge tag 'kvm-4.9-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"All architectures:
- move `make kvmconfig` stubs from x86
- use 64 bits for debugfs stats
ARM:
- Important fixes for not using an in-kernel irqchip
- handle SError exceptions and present them to guests if appropriate
- proxying of GICV access at EL2 if guest mappings are unsafe
- GICv3 on AArch32 on ARMv8
- preparations for GICv3 save/restore, including ABI docs
- cleanups and a bit of optimizations
MIPS:
- A couple of fixes in preparation for supporting MIPS EVA host
kernels
- MIPS SMP host & TLB invalidation fixes
PPC:
- Fix the bug which caused guests to falsely report lockups
- other minor fixes
- a small optimization
s390:
- Lazy enablement of runtime instrumentation
- up to 255 CPUs for nested guests
- rework of machine check deliver
- cleanups and fixes
x86:
- IOMMU part of AMD's AVIC for vmexit-less interrupt delivery
- Hyper-V TSC page
- per-vcpu tsc_offset in debugfs
- accelerated INS/OUTS in nVMX
- cleanups and fixes"
* tag 'kvm-4.9-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (140 commits)
KVM: MIPS: Drop dubious EntryHi optimisation
KVM: MIPS: Invalidate TLB by regenerating ASIDs
KVM: MIPS: Split kernel/user ASID regeneration
KVM: MIPS: Drop other CPU ASIDs on guest MMU changes
KVM: arm/arm64: vgic: Don't flush/sync without a working vgic
KVM: arm64: Require in-kernel irqchip for PMU support
KVM: PPC: Book3s PR: Allow access to unprivileged MMCR2 register
KVM: PPC: Book3S PR: Support 64kB page size on POWER8E and POWER8NVL
KVM: PPC: Book3S: Remove duplicate setting of the B field in tlbie
KVM: PPC: BookE: Fix a sanity check
KVM: PPC: Book3S HV: Take out virtual core piggybacking code
KVM: PPC: Book3S: Treat VTB as a per-subcore register, not per-thread
ARM: gic-v3: Work around definition of gic_write_bpr1
KVM: nVMX: Fix the NMI IDT-vectoring handling
KVM: VMX: Enable MSR-BASED TPR shadow even if APICv is inactive
KVM: nVMX: Fix reload apic access page warning
kvmconfig: add virtio-gpu to config fragment
config: move x86 kvm_guest.config to a common location
arm64: KVM: Remove duplicating init code for setting VMID
ARM: KVM: Support vgic-v3
...
Subsystem improvements:
- Do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to
me). We can now select GPIOLIB and be done with it, for all
archs. After some struggle it even work on UM. Not that it has
GPIO, but if it wants to, it can select the library.
- Continued efforts to make drivers properly either tristate or
bool.
- Introduce a warning for drivers assigning default triggers to
their irqchip lines when probed from device tree, so we find and
fix these ambigous drivers. It is agreed that in the OF config
path, the device tree defines trigger characteristics.
- The same warning, mutatis mutandis, for ACPI-probed GPIO
irqchips.
- We introduce the ability to mark certain IRQ lines as "unusable"
as they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is
put to good use in the STMPE driver and also in the Cherryview
pin control driver.
- A new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- Make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM
with allyesconfig or allmodconfig it exploded in their face.
- Move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so
now eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- New driver for the Aspeed GPIO front-end companion to the
pin controller merged through the pin control tree.
- New driver for the LP873x PMIC GPIO portions.
- New driver for Technologic Systems' I2C FPGA GPIO such as
TS4900, TS-7970, TS-7990 and TS-4100.
- New driver for the Broadcom BCM63xx series including BCM6338
and BCM6345.
- New driver for the Intel WhiskeyCove PMIC GPIO.
- New driver for the Allwinner AXP209 PMIC GPIO portions.
- New driver for Diamond Systems 48 line GPIO-MM, another of
these port-mapped I/O expansion cards.
- Support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- The STMPE driver now supports rising/falling edge detection
properly for IRQs.
- The PCA954x will now fetch and enable its VCC regulator properly.
- Major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- Switch the IOP driver to use the generic MMIO GPIO library.
- Move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns.
-----BEGIN PGP SIGNATURE-----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=ABbi
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.9 series:
Subsystem improvements:
- do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to me). We
can now select GPIOLIB and be done with it, for all archs. After
some struggle it even work on UM. Not that it has GPIO, but if it
wants to, it can select the library.
- continued efforts to make drivers properly either tristate or bool.
- introduce a warning for drivers assigning default triggers to their
irqchip lines when probed from device tree, so we find and fix
these ambigous drivers. It is agreed that in the OF config path,
the device tree defines trigger characteristics.
- the same warning, mutatis mutandis, for ACPI-probed GPIO irqchips.
- we introduce the ability to mark certain IRQ lines as "unusable" as
they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is put to
good use in the STMPE driver and also in the Cherryview pin control
driver.
- a new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM with
allyesconfig or allmodconfig it exploded in their face.
- move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so now
eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- new driver for the Aspeed GPIO front-end companion to the pin
controller merged through the pin control tree.
- new driver for the LP873x PMIC GPIO portions.
- new driver for Technologic Systems' I2C FPGA GPIO such as TS4900,
TS-7970, TS-7990 and TS-4100.
- new driver for the Broadcom BCM63xx series including BCM6338 and
BCM6345.
- new driver for the Intel WhiskeyCove PMIC GPIO.
- new driver for the Allwinner AXP209 PMIC GPIO portions.
- new driver for Diamond Systems 48 line GPIO-MM, another of these
port-mapped I/O expansion cards.
- support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- the STMPE driver now supports rising/falling edge detection
properly for IRQs.
- the PCA954x will now fetch and enable its VCC regulator properly.
- major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- switch the IOP driver to use the generic MMIO GPIO library.
- move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns"
* tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (81 commits)
gpio: add missing static inline
gpio: OF: localize some gpiochip init functions
gpio: acpi: separation of concerns
gpio: OF: separation of concerns
gpio: make memory-mapped drivers depend on HAS_IOMEM
gpio: stmpe: use BIT() macro
gpio: stmpe: forbid unused lines to be mapped as IRQs
mfd/gpio: Move HTC GPIO driver to GPIO subsystem
gpio: MAINTAINERS: Add an entry for GPIO mockup driver
gpio/mockup: add virtual gpio device
gpio: Added zynq specific check for special pins on bank zero
gpio: axp209: Implement get_direction
gpio: aspeed: remove redundant return value check
gpio: loongson1: remove redundant return value check
ARM: omap2: fix missing include
gpio: tc3589x: fix up complaints on unsigned
gpio: tc3589x: add .get_direction() and small cleanup
gpio: f7188x: use gpiochip_get_data instead of container_of
gpio: tps65218: use devm_gpiochip_add_data() for gpio registration
gpio: aspeed: fix return value check in aspeed_gpio_probe()
...
Pull networking updates from David Miller:
1) BBR TCP congestion control, from Neal Cardwell, Yuchung Cheng and
co. at Google. https://lwn.net/Articles/701165/
2) Do TCP Small Queues for retransmits, from Eric Dumazet.
3) Support collect_md mode for all IPV4 and IPV6 tunnels, from Alexei
Starovoitov.
4) Allow cls_flower to classify packets in ip tunnels, from Amir Vadai.
5) Support DSA tagging in older mv88e6xxx switches, from Andrew Lunn.
6) Support GMAC protocol in iwlwifi mwm, from Ayala Beker.
7) Support ndo_poll_controller in mlx5, from Calvin Owens.
8) Move VRF processing to an output hook and allow l3mdev to be
loopback, from David Ahern.
9) Support SOCK_DESTROY for UDP sockets. Also from David Ahern.
10) Congestion control in RXRPC, from David Howells.
11) Support geneve RX offload in ixgbe, from Emil Tantilov.
12) When hitting pressure for new incoming TCP data SKBs, perform a
partial rathern than a full purge of the OFO queue (which could be
huge). From Eric Dumazet.
13) Convert XFRM state and policy lookups to RCU, from Florian Westphal.
14) Support RX network flow classification to igb, from Gangfeng Huang.
15) Hardware offloading of eBPF in nfp driver, from Jakub Kicinski.
16) New skbmod packet action, from Jamal Hadi Salim.
17) Remove some inefficiencies in snmp proc output, from Jia He.
18) Add FIB notifications to properly propagate route changes to
hardware which is doing forwarding offloading. From Jiri Pirko.
19) New dsa driver for qca8xxx chips, from John Crispin.
20) Implement RFC7559 ipv6 router solicitation backoff, from Maciej
Żenczykowski.
21) Add L3 mode to ipvlan, from Mahesh Bandewar.
22) Support 802.1ad in mlx4, from Moshe Shemesh.
23) Support hardware LRO in mediatek driver, from Nelson Chang.
24) Add TC offloading to mlx5, from Or Gerlitz.
25) Convert various drivers to ethtool ksettings interfaces, from
Philippe Reynes.
26) TX max rate limiting for cxgb4, from Rahul Lakkireddy.
27) NAPI support for ath10k, from Rajkumar Manoharan.
28) Support XDP in mlx5, from Rana Shahout and Saeed Mahameed.
29) UDP replicast support in TIPC, from Richard Alpe.
30) Per-queue statistics for qed driver, from Sudarsana Reddy Kalluru.
31) Support BQL in thunderx driver, from Sunil Goutham.
32) TSO support in alx driver, from Tobias Regnery.
33) Add stream parser engine and use it in kcm.
34) Support async DHCP replies in ipconfig module, from Uwe
Kleine-König.
35) DSA port fast aging for mv88e6xxx driver, from Vivien Didelot.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1715 commits)
mlxsw: switchx2: Fix misuse of hard_header_len
mlxsw: spectrum: Fix misuse of hard_header_len
net/faraday: Stop NCSI device on shutdown
net/ncsi: Introduce ncsi_stop_dev()
net/ncsi: Rework the channel monitoring
net/ncsi: Allow to extend NCSI request properties
net/ncsi: Rework request index allocation
net/ncsi: Don't probe on the reserved channel ID (0x1f)
net/ncsi: Introduce NCSI_RESERVED_CHANNEL
net/ncsi: Avoid unused-value build warning from ia64-linux-gcc
net: Add netdev all_adj_list refcnt propagation to fix panic
net: phy: Add Edge-rate driver for Microsemi PHYs.
vmxnet3: Wake queue from reset work
i40e: avoid NULL pointer dereference and recursive errors on early PCI error
qed: Add RoCE ll2 & GSI support
qed: Add support for memory registeration verbs
qed: Add support for QP verbs
qed: PD,PKEY and CQ verb support
qed: Add support for RoCE hw init
qede: Add qedr framework
...
buffers (Thor Thayer)
* Split the memory controller part out of mpc85xx and share it with a
* new Freescale ARM Layerscape driver (York Sun)
* amd64_edac fixes (Yazen Ghannam)
* Misc cleanups, refactoring and fixes all over the place
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pcI8
-----END PGP SIGNATURE-----
Merge tag 'edac_for_4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"A lot of movement in the EDAC tree this time around, coarse summary
below:
- Altera Arria10 enablement of NAND, DMA, USB, QSPI and SD-MMC FIFO
buffers (Thor Thayer)
- split the memory controller part out of mpc85xx and share it with a
new Freescale ARM Layerscape driver (York Sun)
- amd64_edac fixes (Yazen Ghannam)
- misc cleanups, refactoring and fixes all over the place"
* tag 'edac_for_4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (37 commits)
EDAC, altera: Add IRQ Flags to disable IRQ while handling
EDAC, altera: Correct EDAC IRQ error message
EDAC, amd64: Autoload module using x86_cpu_id
EDAC, sb_edac: Remove NULL pointer check on array pci_tad
EDAC: Remove NO_IRQ from powerpc-only drivers
EDAC, fsl_ddr: Fix error return code in fsl_mc_err_probe()
EDAC, fsl_ddr: Add entry to MAINTAINERS
EDAC: Move Doug Thompson to CREDITS
EDAC, I3000: Orphan driver
EDAC, fsl_ddr: Replace simple_strtoul() with kstrtoul()
EDAC, layerscape: Add Layerscape EDAC support
EDAC, fsl_ddr: Fix IRQ dispose warning when module is removed
EDAC, fsl_ddr: Add support for little endian
EDAC, fsl_ddr: Add missing DDR DRAM types
EDAC, fsl_ddr: Rename macros and names
EDAC, fsl-ddr: Separate FSL DDR driver from MPC85xx
EDAC, mpc85xx: Replace printk() with pr_* format
EDAC, mpc85xx: Drop setting/clearing RFXE bit in HID1
EDAC, altera: Rename MC trigger to common name
EDAC, altera: Rename device trigger to common name
...
Here is the big TTY and Serial patch set for 4.9-rc1.
It also includes some drivers/dma/ changes, as those were needed by some
serial drivers, and they were all acked by the DMA maintainer. Also in
here is the long-suffering ACPI SPCR patchset, which was passed around
from maintainer to maintainer like a hot-potato. Seems I was the
sucker^Wlucky one. All of those patches have been acked by the various
subsystem maintainers as well.
All of this has been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlfyNjEPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspwIcAn2uN
qCD8xQJ0Cs61hD1nUzhNygG8AJ94I4zz/fPGpyh/CtJfLQwtUdLhNA==
=Rken
-----END PGP SIGNATURE-----
Merge tag 'tty-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial updates from Greg KH:
"Here is the big tty and serial patch set for 4.9-rc1.
It also includes some drivers/dma/ changes, as those were needed by
some serial drivers, and they were all acked by the DMA maintainer.
Also in here is the long-suffering ACPI SPCR patchset, which was
passed around from maintainer to maintainer like a hot-potato. Seems I
was the sucker^Wlucky one. All of those patches have been acked by the
various subsystem maintainers as well.
All of this has been in linux-next with no reported issues"
* tag 'tty-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (111 commits)
Revert "serial: pl011: add console matching function"
MAINTAINERS: update entry for atmel_serial driver
serial: pl011: add console matching function
ARM64: ACPI: enable ACPI_SPCR_TABLE
ACPI: parse SPCR and enable matching console
of/serial: move earlycon early_param handling to serial
Revert "drivers/tty: Explicitly pass current to show_stack"
tty: amba-pl011: Don't complain on -EPROBE_DEFER when no irq
nios2: dts: 10m50: Add tx-threshold parameter
serial: 8250: Set Altera 16550 TX FIFO Threshold
serial: 8250: of: Load TX FIFO Threshold from DT
Documentation: dt: serial: Add TX FIFO threshold parameter
drivers/tty: Explicitly pass current to show_stack
serial: imx: Fix DCD reading
serial: stm32: mark symbols static where possible
serial: xuartps: Add some register initialisation to cdns_early_console_setup()
serial: xuartps: Removed unwanted checks while reading the error conditions
serial: xuartps: Rewrite the interrupt handling logic
serial: stm32: use mapbase instead of membase for DMA
tty/serial: atmel: fix fractional baud rate computation
...
Pull CPU hotplug updates from Thomas Gleixner:
"Yet another batch of cpu hotplug core updates and conversions:
- Provide core infrastructure for multi instance drivers so the
drivers do not have to keep custom lists.
- Convert custom lists to the new infrastructure. The block-mq custom
list conversion comes through the block tree and makes the diffstat
tip over to more lines removed than added.
- Handle unbalanced hotplug enable/disable calls more gracefully.
- Remove the obsolete CPU_STARTING/DYING notifier support.
- Convert another batch of notifier users.
The relayfs changes which conflicted with the conversion have been
shipped to me by Andrew.
The remaining lot is targeted for 4.10 so that we finally can remove
the rest of the notifiers"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
cpufreq: Fix up conversion to hotplug state machine
blk/mq: Reserve hotplug states for block multiqueue
x86/apic/uv: Convert to hotplug state machine
s390/mm/pfault: Convert to hotplug state machine
mips/loongson/smp: Convert to hotplug state machine
mips/octeon/smp: Convert to hotplug state machine
fault-injection/cpu: Convert to hotplug state machine
padata: Convert to hotplug state machine
cpufreq: Convert to hotplug state machine
ACPI/processor: Convert to hotplug state machine
virtio scsi: Convert to hotplug state machine
oprofile/timer: Convert to hotplug state machine
block/softirq: Convert to hotplug state machine
lib/irq_poll: Convert to hotplug state machine
x86/microcode: Convert to hotplug state machine
sh/SH-X3 SMP: Convert to hotplug state machine
ia64/mca: Convert to hotplug state machine
ARM/OMAP/wakeupgen: Convert to hotplug state machine
ARM/shmobile: Convert to hotplug state machine
arm64/FP/SIMD: Convert to hotplug state machine
...
Pull irq updates from Thomas Gleixner:
"The irq departement proudly presents:
- A rework of the core infrastructure to optimally spread interrupt
for multiqueue devices. The first version was a bit naive and
failed to take thread siblings and other details into account.
Developed in cooperation with Christoph and Keith.
- Proper delegation of softirqs to ksoftirqd, so if ksoftirqd is
active then no further softirq processsing on interrupt return
happens. Otherwise we try to delegate and still run another batch
of network packets in the irq return path, which then tries to
delegate to ksoftirqd .....
- A proper machine parseable sysfs based alternative for
/proc/interrupts.
- ACPI support for the GICV3-ITS and ARM interrupt remapping
- Two new irq chips from the ARM SoC zoo: STM32-EXTI and MVEBU-PIC
- A new irq chip for the JCore (SuperH)
- The usual pile of small fixlets in core and irqchip drivers"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (42 commits)
softirq: Let ksoftirqd do its job
genirq: Make function __irq_do_set_handler() static
ARM/dts: Add EXTI controller node to stm32f429
ARM/STM32: Select external interrupts controller
drivers/irqchip: Add STM32 external interrupts support
Documentation/dt-bindings: Document STM32 EXTI controller bindings
irqchip/mips-gic: Use for_each_set_bit to iterate over local IRQs
pci/msi: Retrieve affinity for a vector
genirq/affinity: Remove old irq spread infrastructure
genirq/msi: Switch to new irq spreading infrastructure
genirq/affinity: Provide smarter irq spreading infrastructure
genirq/msi: Add cpumask allocation to alloc_msi_entry
genirq: Expose interrupt information through sysfs
irqchip/gicv3-its: Use MADT ITS subtable to do PCI/MSI domain initialization
irqchip/gicv3-its: Factor out PCI-MSI part that might be reused for ACPI
irqchip/gicv3-its: Probe ITS in the ACPI way
irqchip/gicv3-its: Refactor ITS DT init code to prepare for ACPI
irqchip/gicv3-its: Cleanup for ITS domain initialization
PCI/MSI: Setup MSI domain on a per-device basis using IORT ACPI table
ACPI: Add new IORT functions to support MSI domain handling
...
Pull low-level x86 updates from Ingo Molnar:
"In this cycle this topic tree has become one of those 'super topics'
that accumulated a lot of changes:
- Add CONFIG_VMAP_STACK=y support to the core kernel and enable it on
x86 - preceded by an array of changes. v4.8 saw preparatory changes
in this area already - this is the rest of the work. Includes the
thread stack caching performance optimization. (Andy Lutomirski)
- switch_to() cleanups and all around enhancements. (Brian Gerst)
- A large number of dumpstack infrastructure enhancements and an
unwinder abstraction. The secret long term plan is safe(r) live
patching plus maybe another attempt at debuginfo based unwinding -
but all these current bits are standalone enhancements in a frame
pointer based debug environment as well. (Josh Poimboeuf)
- More __ro_after_init and const annotations. (Kees Cook)
- Enable KASLR for the vmemmap memory region. (Thomas Garnier)"
[ The virtually mapped stack changes are pretty fundamental, and not
x86-specific per se, even if they are only used on x86 right now. ]
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
x86/asm: Get rid of __read_cr4_safe()
thread_info: Use unsigned long for flags
x86/alternatives: Add stack frame dependency to alternative_call_2()
x86/dumpstack: Fix show_stack() task pointer regression
x86/dumpstack: Remove dump_trace() and related callbacks
x86/dumpstack: Convert show_trace_log_lvl() to use the new unwinder
oprofile/x86: Convert x86_backtrace() to use the new unwinder
x86/stacktrace: Convert save_stack_trace_*() to use the new unwinder
perf/x86: Convert perf_callchain_kernel() to use the new unwinder
x86/unwind: Add new unwind interface and implementations
x86/dumpstack: Remove NULL task pointer convention
fork: Optimize task creation by caching two thread stacks per CPU if CONFIG_VMAP_STACK=y
sched/core: Free the stack early if CONFIG_THREAD_INFO_IN_TASK
lib/syscall: Pin the task stack in collect_syscall()
x86/process: Pin the target stack in get_wchan()
x86/dumpstack: Pin the target stack when dumping it
kthread: Pin the stack via try_get_task_stack()/put_task_stack() in to_live_kthread() function
sched/core: Add try_get_task_stack() and put_task_stack()
x86/entry/64: Fix a minor comment rebase error
iommu/amd: Don't put completion-wait semaphore on stack
...
- Support for execute-only page permissions
- Support for hibernate and DEBUG_PAGEALLOC
- Support for heterogeneous systems with mismatches cache line sizes
- Errata workarounds (A53 843419 update and QorIQ A-008585 timer bug)
- arm64 PMU perf updates, including cpumasks for heterogeneous systems
- Set UTS_MACHINE for building rpm packages
- Yet another head.S tidy-up
- Some cleanups and refactoring, particularly in the NUMA code
- Lots of random, non-critical fixes across the board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJX7k31AAoJELescNyEwWM0XX0H/iOaWCfKlWOhvBsStGUCsLrK
XryTzQT2KjdnLKf3jwP+1ateCuBR5ROurYxoDCX5/7mD63c5KiI338Vbv61a1lE1
AAwjt1stmQVUg/j+kqnuQwB/0DYg+2C8se3D3q5Iyn7zc19cDZJEGcBHNrvLMufc
XgHrgHgl/rzBDDlHJXleknDFge/MfhU5/Q1vJMRRb4JYrpAtmIokzCO75CYMRcCT
ND2QbmppKtsyuFPGUTVbAFzJlP6dGKb3eruYta7/ct5d0pJQxav3u98D2yWGfjdM
YaYq1EmX5Pol7rWumqLtk0+mA9yCFcKLLc+PrJu20Vx0UkvOq8G8Xt70sHNvZU8=
=gdPM
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"It's a bit all over the place this time with no "killer feature" to
speak of. Support for mismatched cache line sizes should help people
seeing whacky JIT failures on some SoCs, and the big.LITTLE perf
updates have been a long time coming, but a lot of the changes here
are cleanups.
We stray outside arch/arm64 in a few areas: the arch/arm/ arch_timer
workaround is acked by Russell, the DT/OF bits are acked by Rob, the
arch_timer clocksource changes acked by Marc, CPU hotplug by tglx and
jump_label by Peter (all CC'd).
Summary:
- Support for execute-only page permissions
- Support for hibernate and DEBUG_PAGEALLOC
- Support for heterogeneous systems with mismatches cache line sizes
- Errata workarounds (A53 843419 update and QorIQ A-008585 timer bug)
- arm64 PMU perf updates, including cpumasks for heterogeneous systems
- Set UTS_MACHINE for building rpm packages
- Yet another head.S tidy-up
- Some cleanups and refactoring, particularly in the NUMA code
- Lots of random, non-critical fixes across the board"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (100 commits)
arm64: tlbflush.h: add __tlbi() macro
arm64: Kconfig: remove SMP dependence for NUMA
arm64: Kconfig: select OF/ACPI_NUMA under NUMA config
arm64: fix dump_backtrace/unwind_frame with NULL tsk
arm/arm64: arch_timer: Use archdata to indicate vdso suitability
arm64: arch_timer: Work around QorIQ Erratum A-008585
arm64: arch_timer: Add device tree binding for A-008585 erratum
arm64: Correctly bounds check virt_addr_valid
arm64: migrate exception table users off module.h and onto extable.h
arm64: pmu: Hoist pmu platform device name
arm64: pmu: Probe default hw/cache counters
arm64: pmu: add fallback probe table
MAINTAINERS: Update ARM PMU PROFILING AND DEBUGGING entry
arm64: Improve kprobes test for atomic sequence
arm64/kvm: use alternative auto-nop
arm64: use alternative auto-nop
arm64: alternative: add auto-nop infrastructure
arm64: lse: convert lse alternatives NOP padding to use __nops
arm64: barriers: introduce nops and __nops macros for NOP sequences
arm64: sysreg: replace open-coded mrs_s/msr_s with {read,write}_sysreg_s
...
- Various cleanups and removal of redundant code
- Two important fixes for not using an in-kernel irqchip
- A bit of optimizations
- Handle SError exceptions and present them to guests if appropriate
- Proxying of GICV access at EL2 if guest mappings are unsafe
- GICv3 on AArch32 on ARMv8
- Preparations for GICv3 save/restore, including ABI docs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJX6rKQAAoJEEtpOizt6ddy8i4H/0bfB1EVukggoL/FfGeds/dg
p2FG0oOsggcSBwK7VXUUvVllO7ioUssRCqqkn1e0/bCLtQrN4ex4PqJ3618EHFz/
pLP72hf8Zl33rP3OVtPaDcxzjjKKdf+xGbBIv3AE7x7O5rFZg4lWHeWjy4yuhFv2
Jm+8ul7JCxCMse08Xc90riou4i/jWjyoLadHbAoeX3tR+dVcZyOUZSlgAPI1bS/P
rOQi/zkl3bT2R3kh28QuEFTrJ9BVTnmw25BRW8DNr6+CWmR9bpM6y7AGzOwrZ3FZ
F1MbsPpN3ogcjvPg2QTYuOoqrwz8NLLHw5pR5YNj84VppjSpSsAhKU7Ug5Uhsr0=
=1z/L
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into next
KVM/ARM Changes for v4.9
- Various cleanups and removal of redundant code
- Two important fixes for not using an in-kernel irqchip
- A bit of optimizations
- Handle SError exceptions and present them to guests if appropriate
- Proxying of GICV access at EL2 if guest mappings are unsafe
- GICv3 on AArch32 on ARMv8
- Preparations for GICv3 save/restore, including ABI docs
This patch adds the L2 cache topology for berlin4ct which has 1MB L2
cache.
[Sebastian: rename cache node from "l2-cache" to "cache"]
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
After commit f29a72c24a ("watchdog: dw_wdt: Convert to use watchdog
infrastructure"), the dw_wdt driver can support multiple variants, so
unconditionally enable all dw_wdt nodes now.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Commit ac82d12772 ("arm64: perf: add Cortex-A53 support") adds the
cortex A53 PMU support, thus instead of using the generic armv8-pmuv3
compatibility use the more specific Cortex A53 compatibility.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
SBBR mentions SPCR as a mandatory ACPI table. So enable it for ARM64
Earlycon should be set up as early as possible. ACPI boot tables are
mapped in arch/arm64/kernel/acpi.c:acpi_boot_table_init() that
is called from setup_arch() and that's where we parse SPCR.
So it has to be opted-in per-arch.
When ACPI_SPCR_TABLE is defined initialization of DT earlycon is
deferred until the DT/ACPI decision is done. Initialize DT earlycon
if ACPI is disabled.
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As with dsb() and isb(), add a __tlbi() helper so that we can avoid
distracting asm boilerplate every time we want a TLBI. As some TLBI
operations take an argument while others do not, some pre-processor is
used to handle these two cases with different assembly blocks.
The existing tlbflush.h code is moved over to use the helper.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
[ rename helper to __tlbi, update comment and commit log ]
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The arm64 forces CONFIG_SMP=y with commit 4b3dc9679c, no need to
add SMP dependence for NUMA.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Enable throttle function for SOC_THERM.
Set "hot" trips for cpu and gpu thermal zones, which
can trigger the SOC_THERM hardware throttle.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Set general "critical" trip temperatures for cpu, gpu, mem and pllx
thermal zones on Tegra210, these trips can trigger shut down or reset.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Adds soctherm node for Tegra210, and add cpu,
gpu, mem, pllx as thermal-zones. Set critical
trip temperatures for them.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Enable throttle function for SOC_THERM.
Set "hot" trips for cpu and gpu thermal zones, which
can trigger the SOC_THERM hardware throttle.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Set general "critical" trip temperatures for cpu, gpu, mem and pllx
thermal zones on Tegra132, these trips can trigger shut down or reset.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The Tegra132 has the specific settings for soctherm,
so change to use campatible "nvidia,tegra132-soctherm" for it.
And adds cpu, gpu, mem and pllx thermal zones.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Move OF_NUMA select under NUMA config, and select ACPI_NUMA
when ACPI enabled.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In some places, dump_backtrace() is called with a NULL tsk parameter,
e.g. in bug_handler() in arch/arm64, or indirectly via show_stack() in
core code. The expectation is that this is treated as if current were
passed instead of NULL. Similar is true of unwind_frame().
Commit a80a0eb70c ("arm64: make irq_stack_ptr more robust") didn't
take this into account. In dump_backtrace() it compares tsk against
current *before* we check if tsk is NULL, and in unwind_frame() we never
set tsk if it is NULL.
Due to this, we won't initialise irq_stack_ptr in either function. In
dump_backtrace() this results in calling dump_mem() for memory
immediately above the IRQ stack range, rather than for the relevant
range on the task stack. In unwind_frame we'll reject unwinding frames
on the IRQ stack.
In either case this results in incomplete or misleading backtrace
information, but is not otherwise problematic. The initial percpu areas
(including the IRQ stacks) are allocated in the linear map, and dump_mem
uses __get_user(), so we shouldn't access anything with side-effects,
and will handle holes safely.
This patch fixes the issue by having both functions handle the NULL tsk
case before doing anything else with tsk.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Fixes: a80a0eb70c ("arm64: make irq_stack_ptr more robust")
Acked-by: James Morse <james.morse@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yang Shi <yang.shi@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
- Fix kgdb breakpoint insertion in read-only text sections (when
CONFIG_DEBUG_RODATA or CONFIG_DEBUG_SET_MODULE_RONX are enabled)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NCBp
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"A couple of last-minute arm64 fixes for 4.8:
- Fix secondary CPU to NUMA node assignment
- Fix kgdb breakpoint insertion in read-only text sections (when
CONFIG_DEBUG_RODATA or CONFIG_DEBUG_SET_MODULE_RONX are enabled)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: kgdb: handle read-only text / modules
arm64: Call numa_store_cpu_info() earlier.
Instead of comparing the name to a magic string, use archdata to
explicitly communicate whether the arch timer is suitable for
direct vdso access.
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Erratum A-008585 says that the ARM generic timer counter "has the
potential to contain an erroneous value for a small number of core
clock cycles every time the timer value changes". Accesses to TVAL
(both read and write) are also affected due to the implicit counter
read. Accesses to CVAL are not affected.
The workaround is to reread TVAL and count registers until successive
reads return the same value. Writes to TVAL are replaced with an
equivalent write to CVAL.
The workaround is to reread TVAL and count registers until successive reads
return the same value, and when writing TVAL to retry until counter
reads before and after the write return the same value.
The workaround is enabled if the fsl,erratum-a008585 property is found in
the timer node in the device tree. This can be overridden with the
clocksource.arm_arch_timer.fsl-a008585 boot parameter, which allows KVM
users to enable the workaround until a mechanism is implemented to
automatically communicate this information.
This erratum can be found on LS1043A and LS2080A.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Scott Wood <oss@buserror.net>
[will: renamed read macro to reflect that it's not usually unstable]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Handle read-only cases when CONFIG_DEBUG_RODATA (4.0) or
CONFIG_DEBUG_SET_MODULE_RONX (3.18) are enabled by using
aarch64_insn_write() instead of probe_kernel_write() as introduced by
commit 2f896d5866 ("arm64: use fixmap for text patching") in 4.0.
Fixes: 11d91a770f ("arm64: Add CONFIG_DEBUG_SET_MODULE_RONX support")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The wq_numa_init() function makes a private CPU to node map by calling
cpu_to_node() early in the boot process, before the non-boot CPUs are
brought online. Since the default implementation of cpu_to_node()
returns zero for CPUs that have never been brought online, the
workqueue system's view is that *all* CPUs are on node zero.
When the unbound workqueue for a non-zero node is created, the
tsk_cpus_allowed() for the worker threads is the empty set because
there are, in the view of the workqueue system, no CPUs on non-zero
nodes. The code in try_to_wake_up() using this empty cpumask ends up
using the cpumask empty set value of NR_CPUS as an index into the
per-CPU area pointer array, and gets garbage as it is one past the end
of the array. This results in:
[ 0.881970] Unable to handle kernel paging request at virtual address fffffb1008b926a4
[ 1.970095] pgd = fffffc00094b0000
[ 1.973530] [fffffb1008b926a4] *pgd=0000000000000000, *pud=0000000000000000, *pmd=0000000000000000
[ 1.982610] Internal error: Oops: 96000004 [#1] SMP
[ 1.987541] Modules linked in:
[ 1.990631] CPU: 48 PID: 295 Comm: cpuhp/48 Tainted: G W 4.8.0-rc6-preempt-vol+ #9
[ 1.999435] Hardware name: Cavium ThunderX CN88XX board (DT)
[ 2.005159] task: fffffe0fe89cc300 task.stack: fffffe0fe8b8c000
[ 2.011158] PC is at try_to_wake_up+0x194/0x34c
[ 2.015737] LR is at try_to_wake_up+0x150/0x34c
[ 2.020318] pc : [<fffffc00080e7468>] lr : [<fffffc00080e7424>] pstate: 600000c5
[ 2.027803] sp : fffffe0fe8b8fb10
[ 2.031149] x29: fffffe0fe8b8fb10 x28: 0000000000000000
[ 2.036522] x27: fffffc0008c63bc8 x26: 0000000000001000
[ 2.041896] x25: fffffc0008c63c80 x24: fffffc0008bfb200
[ 2.047270] x23: 00000000000000c0 x22: 0000000000000004
[ 2.052642] x21: fffffe0fe89d25bc x20: 0000000000001000
[ 2.058014] x19: fffffe0fe89d1d00 x18: 0000000000000000
[ 2.063386] x17: 0000000000000000 x16: 0000000000000000
[ 2.068760] x15: 0000000000000018 x14: 0000000000000000
[ 2.074133] x13: 0000000000000000 x12: 0000000000000000
[ 2.079505] x11: 0000000000000000 x10: 0000000000000000
[ 2.084879] x9 : 0000000000000000 x8 : 0000000000000000
[ 2.090251] x7 : 0000000000000040 x6 : 0000000000000000
[ 2.095621] x5 : ffffffffffffffff x4 : 0000000000000000
[ 2.100991] x3 : 0000000000000000 x2 : 0000000000000000
[ 2.106364] x1 : fffffc0008be4c24 x0 : ffffff0ffffada80
[ 2.111737]
[ 2.113236] Process cpuhp/48 (pid: 295, stack limit = 0xfffffe0fe8b8c020)
[ 2.120102] Stack: (0xfffffe0fe8b8fb10 to 0xfffffe0fe8b90000)
[ 2.125914] fb00: fffffe0fe8b8fb80 fffffc00080e7648
.
.
.
[ 2.442859] Call trace:
[ 2.445327] Exception stack(0xfffffe0fe8b8f940 to 0xfffffe0fe8b8fa70)
[ 2.451843] f940: fffffe0fe89d1d00 0000040000000000 fffffe0fe8b8fb10 fffffc00080e7468
[ 2.459767] f960: fffffe0fe8b8f980 fffffc00080e4958 ffffff0ff91ab200 fffffc00080e4b64
[ 2.467690] f980: fffffe0fe8b8f9d0 fffffc00080e515c fffffe0fe8b8fa80 0000000000000000
[ 2.475614] f9a0: fffffe0fe8b8f9d0 fffffc00080e58e4 fffffe0fe8b8fa80 0000000000000000
[ 2.483540] f9c0: fffffe0fe8d10000 0000000000000040 fffffe0fe8b8fa50 fffffc00080e5ac4
[ 2.491465] f9e0: ffffff0ffffada80 fffffc0008be4c24 0000000000000000 0000000000000000
[ 2.499387] fa00: 0000000000000000 ffffffffffffffff 0000000000000000 0000000000000040
[ 2.507309] fa20: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
[ 2.515233] fa40: 0000000000000000 0000000000000000 0000000000000000 0000000000000018
[ 2.523156] fa60: 0000000000000000 0000000000000000
[ 2.528089] [<fffffc00080e7468>] try_to_wake_up+0x194/0x34c
[ 2.533723] [<fffffc00080e7648>] wake_up_process+0x28/0x34
[ 2.539275] [<fffffc00080d3764>] create_worker+0x110/0x19c
[ 2.544824] [<fffffc00080d69dc>] alloc_unbound_pwq+0x3cc/0x4b0
[ 2.550724] [<fffffc00080d6bcc>] wq_update_unbound_numa+0x10c/0x1e4
[ 2.557066] [<fffffc00080d7d78>] workqueue_online_cpu+0x220/0x28c
[ 2.563234] [<fffffc00080bd288>] cpuhp_invoke_callback+0x6c/0x168
[ 2.569398] [<fffffc00080bdf74>] cpuhp_up_callbacks+0x44/0xe4
[ 2.575210] [<fffffc00080be194>] cpuhp_thread_fun+0x13c/0x148
[ 2.581027] [<fffffc00080dfbac>] smpboot_thread_fn+0x19c/0x1a8
[ 2.586929] [<fffffc00080dbd64>] kthread+0xdc/0xf0
[ 2.591776] [<fffffc0008083380>] ret_from_fork+0x10/0x50
[ 2.597147] Code: b00057e1 91304021 91005021 b8626822 (b8606821)
[ 2.603464] ---[ end trace 58c0cd36b88802bc ]---
[ 2.608138] Kernel panic - not syncing: Fatal exception
Fix by moving call to numa_store_cpu_info() for all CPUs into
smp_prepare_cpus(), which happens before wq_numa_init(). Since
smp_store_cpu_info() now contains only a single function call,
simplify by removing the function and out-lining its contents.
Suggested-by: Robert Richter <rric@kernel.org>
Fixes: 1a2db30034 ("arm64, numa: Add NUMA support for arm64 platforms.")
Cc: <stable@vger.kernel.org> # 4.7.x-
Signed-off-by: David Daney <david.daney@cavium.com>
Reviewed-by: Robert Richter <rrichter@cavium.com>
Tested-by: Yisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch allows to build and use vgic-v3 in 32-bit mode.
Unfortunately, it can not be split in several steps without extra
stubs to keep patches independent and bisectable. For instance,
virt/kvm/arm/vgic/vgic-v3.c uses function from vgic-v3-sr.c, handling
access to GICv3 cpu interface from the guest requires vgic_v3.vgic_sre
to be already defined.
It is how support has been done:
* handle SGI requests from the guest
* report configured SRE on access to GICv3 cpu interface from the guest
* required vgic-v3 macros are provided via uapi.h
* static keys are used to select GIC backend
* to make vgic-v3 build KVM_ARM_VGIC_V3 guard is removed along with
the static inlines
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
By now ITS code guarded with KVM_ARM_VGIC_V3 config option which was
introduced to hide everything specific to vgic-v3 from 32-bit world.
We are going to support vgic-v3 in 32-bit world and KVM_ARM_VGIC_V3
will gone, but we don't have support for ITS there yet and we need to
continue keeping ITS away.
Introduce the new config option to prevent ITS code being build in
32-bit mode when support for vgic-v3 is done.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
So we can reuse the code under arch/arm
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Since we are going to share vgic-v3 save/restore code with ARM keep
arch specific accessors separately.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Currently GIC backend is selected via alternative framework and this
is fine. We are going to introduce vgic-v3 to 32-bit world and there
we don't have patching framework in hand, so we can either check
support for GICv3 every time we need to choose which backend to use or
try to optimise it by using static keys. The later looks quite
promising because we can share logic involved in selecting GIC backend
between architectures if both uses static keys.
This patch moves arm64 from alternative to static keys framework for
selecting GIC backend. For that we embed static key into vgic_global
and enable the key during vgic initialisation based on what has
already been exposed by the host GIC driver.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
virt_addr_valid is supposed to return true if and only if virt_to_page
returns a valid page structure. The current macro does math on whatever
address is given and passes that to pfn_valid to verify. vmalloc and
module addresses can happen to generate a pfn that 'happens' to be
valid. Fix this by only performing the pfn_valid check on addresses that
have the potential to be valid.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
I2C and SPI interfaces share common clock trees within the CP110 HW block.
It occurred that SPI0 interface has wrong clock assignment in the device
tree, which is fixed in this commit to a proper value.
Fixes: 728dacc7f4 ("arm64: dts: marvell: initial DT description of ...")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
CC: <stable@vger.kernel.org> v4.7+
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
These files were only including module.h for exception table
related functions. We've now separated that content out into its
own file "extable.h" so now move over to that and avoid all the
extra header content in module.h that we don't really need to compile
these files.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
- Enable ZTE ZX family support in arm64 defconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJX25FiAAoJEFBXWFqHsHzOzJ4IAKAxI7W3Ubnhdxdu8akLYm6a
VHtnqSyr43kKCUEbg05+oTmPzXVF7YdnYmZpyy2mhA9+wpGC6vSwtSDM6Tj8KN8H
ZGzR5Op94GPN3RnLRyGlplltMEbH4I8l6A7SsiJ5VB4Uab2x4bmBagW/vG0O+XuP
exzGQoqlrI5N2gmiSf6P+2Y1oEM+JvClvWPdb9zkMb0B4i8kNJgh+efyNaCv7m/R
v0s9f9AhhK3Saj2TSaJuGuZNHw9vZpDUiOuyTOvnc35bJLjy0AsWqw4BfK8NegQE
4tgXiyVdZxOHvUtAQgw7b2Wkcxo+407zDJE1q6HxR2uudpuTHm0hyWxN62MuXm8=
=zgWs
-----END PGP SIGNATURE-----
Merge tag 'zte-defconfig64-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/arm64
Pull "ZTE arm64 defconfig updates for 4.9" from Shawn Guo:
- Enable ZTE ZX family support in arm64 defconfig
* tag 'zte-defconfig64-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: defconfig: enable ZTE ZX related config
- Add a Kconfig option for ZTE ZX SoC family support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJX25GmAAoJEFBXWFqHsHzOIh4H/30QlDQQyiPzTeKIn0Tfriyj
aL13JVMxCIdGGLN3U1ruZReVwlBMnr14uWsjl7lFT3+VeOSEwyXbCzwn1SKGQ7uh
GQ91KColUy2iFpWnhRCQHPUSUlBUq4R1qR4apP8laaM/xfS7QpG6dghzYcbwnrYG
U51SLecjN234Oca5z7B1kIlOnxSxexEZfPIP2XfT1+ju+NyyU0yjSnLlAAgYVtbW
SNAqrHj4gaZBe7VZB5hfE1ABPVjaXP8f8lkO9ihMHjR5tqEgfgZmayWKdVpR6Ky6
7y0UzUBIuu9WDCvvTqIEXahG3Up+/eeN6lqi4XBlnBGJee+5LBGQ8iyamh5B7CY=
=RDGI
-----END PGP SIGNATURE-----
Merge tag 'zte-soc64-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/arm64
Pull "ZTE arm64 SoC changes for 4.9" from Shawn Guo:
- Add a Kconfig option for ZTE ZX SoC family support
* tag 'zte-soc64-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: add ZTE ZX SoC family
- Add initial DTS support for ZTE ZX296718 SoC and ZX296718 EVB board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJX22SoAAoJEFBXWFqHsHzOypkIAIj88TKFW6IWuiM+mFwu2Q3X
3sqKB11szxucCd8XYHUQ/wknZX33sDSj63mUbYN20Mb4AbA7u1KG/hR6mBIq3no7
xnIDixq6kIMmt3dY6OEgu3qlkEQnrbopcp7bt3N1QtXNtQazt5WWStSzBwAz1Qsq
QQMUjoOyp3sx3E48HiAmPo2R8oh231w44aKS87YU7IIa3Ld9SyNW6/t8sAAhqvWH
1DLFNgZ968jmbb46BylPSHslMSmjrv1HR+5nZ3zNOQeDcRvLqi7+z9xqhwJUVr08
DXh90RaZNSULHlMWL3lEBLR9KTlca2+08c4ax5YOVeAQjaf+ZUAQUPGod+IBW7M=
=KfUg
-----END PGP SIGNATURE-----
Merge tag 'zte-dt64-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt64
Pull "ZTE arm64 device tree changes for 4.9" from Shawn Guo:
- Add initial DTS support for ZTE ZX296718 SoC and ZX296718 EVB board.
* tag 'zte-dt64-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: Add ZTE ZX296718 SoC dts and Makefile
- enable MSI for PCIe on Armada 7K/8K
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlfZZyIACgkQCwYYjhRyO9WV9wCgplO/RTXtSazA02kkUsDSPezd
tVkAnREnwZSo9CzGdQnEztgOpihvgBMH
=2st8
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.9-2' of git://git.infradead.org/linux-mvebu into next/dt64
Pull "mvebu dt64 for 4.9 (part 2)" from Gregory CLEMENT:
- enable MSI for PCIe on Armada 7K/8K
* tag 'mvebu-dt64-4.9-2' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: enable MSI for PCIe on Armada 7K/8K
Pull crypto fixes from Herbert Xu:
"This fixes a potential weakness in IPsec CBC IV generation, as well as
a number of issues that arose out of an OOM crash on ARM with CTR-mode
AES"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: arm64/aes-ctr - fix NULL dereference in tail processing
crypto: arm/aes-ctr - fix NULL dereference in tail processing
crypto: skcipher - Fix blkcipher walk OOM crash
crypto: echainiv - Replace chaining with multiplication
Here are a couple of bugfixes for v4.8-rc. Most of them have
actually been around for a while this time but for some reason
didn't get applied early on. The shmobile regulator fix is the
only one that isn't completely obvious.
device tree changes:
- archtimer interrupts must be level triggered (multiple platforms)
- fix for USB and MMC clocks on STiH410
- fix split DT repository in case of raspberry-pi 3
- A new use of skeleton.dtsi on arm64 has crept in after that
was removed.
defconfig updates:
- xilinx vdma has a new Kconfig symbol name
- keystone requires CONFIG_NOP_USB_XCEIV since v4.8-rc1
code fixes:
- fix regulator quirk on shmobile
- suspend-to-ram regression on EXYNOS
maintainer updates:
- Javier Martinez Canillas is now a reviewer for Samsung EXYNOS
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tYAb
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are a couple of bugfixes for v4.8-rc.
Most of them have actually been around for a while this time but for
some reason didn't get applied early on. The shmobile regulator fix
is the only one that isn't completely obvious.
Device tree changes:
- archtimer interrupts must be level triggered (multiple platforms)
- fix for USB and MMC clocks on STiH410
- fix split DT repository in case of raspberry-pi 3
- a new use of skeleton.dtsi on arm64 has crept in after that was
removed.
defconfig updates:
- xilinx vdma has a new Kconfig symbol name
- keystone requires CONFIG_NOP_USB_XCEIV since v4.8-rc1
Code fixes:
- fix regulator quirk on shmobile
- suspend-to-ram regression on EXYNOS
Maintainer updates:
- Javier Martinez Canillas is now a reviewer for Samsung EXYNOS"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: keystone: defconfig: Fix USB configuration
arm64: dts: Fix broken architected timer interrupt trigger
ARM: multi_v7_defconfig: update XILINX_VDMA
ARM64: dts: bcm: Use a symlink to R-Pi dtsi files from arch=arm
ARM: dts: Remove use of skeleton.dtsi from bcm283x.dtsi
ARM: dts: STiH407-family: Provide interconnect clock for consumption in ST SDHCI
ARM: dts: STiH410: Handle interconnect clock required by EHCI/OHCI (USB)
ARM: shmobile: fix regulator quirk for Gen2
ARM: EXYNOS: Clear OF_POPULATED flag from PMU node in IRQ init callback
MAINTAINERS: Add myself as reviewer for Samsung Exynos support
Move the PMU name into a common header file so it may
be referenced by other users.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ARMv8 machines can identify the micro/arch defined counters
that are available on a machine. Add all these counters to the
default armv8 perf map. At run-time disable the counters which
are not available on the given PMU.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In preparation for ACPI support, add a pmu_probe_info table to
the arm_pmu_device_probe() call. This table gets used when
probing in the absence of a devicetree node for PMU.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
With our DMA ops enabled for PCI devices, we should avoid allocating
IOVAs which a host bridge might misinterpret as peer-to-peer DMA and
lead to faults, corruption or other badness. To be safe, punch out holes
for all of the relevant host bridge's windows when initialising a DMA
domain for a PCI device.
CC: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Inki Dae <inki.dae@samsung.com>
Reported-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch introduces ARCH_ZX to add the support of the ZTE ZX SoC
family for the arm64 architecture.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device tree support for ZX296718 SoC and evaluation board based
on it. Also document new values.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable both gxbb USB controller and add a 5V regulator for the OTG port
VBUS
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable both gxbb USB controller and add a 5V regulator for the OTG port
VBUS
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[khilman: rename vbus node to match P200 schematics]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Kprobes searches backwards a finite number of instructions to determine if
there is an attempt to probe a load/store exclusive sequence. It stops when
it hits the maximum number of instructions or a load or store exclusive.
However this means it can run up past the beginning of the function and
start looking at literal constants. This has been shown to cause a false
positive and blocks insertion of the probe. To fix this, further limit the
backwards search to stop if it hits a symbol address from kallsyms. The
presumption is that this is the entry point to this code (particularly for
the common case of placing probes at the beginning of functions).
This also improves efficiency by not searching code that is not part of the
function. There may be some possibility that the label might not denote the
entry path to the probed instruction but the likelihood seems low and this
is just another example of how the kprobes user really needs to be
careful about what they are doing.
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
the following:
- collective effort from Florian, Doug and Markus to add the ARCH_BRCMSTB Kconfig
symbol to the ARM64 kernel build, which is purposedly the same as the ARM/Linux
one in order not to update any driver dependencies
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AjHP
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.9/soc-arm64' of http://github.com/Broadcom/stblinux into next/arm64
Pull "Broadcom soc-arm64 changes for 4.9" from Florian Fainelli:
This pull request contains Broadcom ARM64-based SoC changes for 4.9, please pull
the following:
- collective effort from Florian, Doug and Markus to add the ARCH_BRCMSTB Kconfig
symbol to the ARM64 kernel build, which is purposedly the same as the ARM/Linux
one in order not to update any driver dependencies
* tag 'arm-soc/for-4.9/soc-arm64' of http://github.com/Broadcom/stblinux:
arm64: Add Broadcom Set Top Box Kconfig entry point
Enable common modules for power management; one is to enable
CPUFREQ_DT driver; the driver is used by many platforms by passing OPP
table from device tree.
Also enables thermal related drivers. Firstly we need enable
configuration CPU_THERMAL for CPU cooling device driver, this will bind
thermal zone with CPU cooling device; and enable 'power allocator'
thermal governor.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- add PCIe driver for Aardvark for Armada 3700
- enable xhci-platform for A7K/A8K
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlfMQewACgkQCwYYjhRyO9WrKgCeJWuHOFUlMYoZqEYKkdA5aJ9G
iPsAoIFQivT7yCn9p7rJKzKt2NI4skoy
=jIwM
-----END PGP SIGNATURE-----
Merge tag 'mvebu-defconfig64-4.9-1' of git://git.infradead.org/linux-mvebu into next/arm64
Pull "mvebu defconfig64 for 4.9 (part 1)" from Gregory CLEMENT:
- add PCIe driver for Aardvark for Armada 3700
- enable xhci-platform for A7K/A8K
* tag 'mvebu-defconfig64-4.9-1' of git://git.infradead.org/linux-mvebu:
arm64: configs: enable PCIe driver for Aardvark
arm64: defconfig: enable xhci-platform
drivers/char/hw_random/Kconfig has 'default m', so
simply removing this entry from the defconfig will
enable building HW random drivers as modules.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Enable hisilicon SAS and XGE for hip05 and hip06
- Enable drm, powerkey, bluetooth and adv7511/adv7533 for hikey
- Add PINCTRL to HISI platform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=y80h
-----END PGP SIGNATURE-----
Merge tag 'hisi-defconfig-for-4.9' of git://github.com/hisilicon/linux-hisi into next/arm64
Pull "ARM64: hisilicon: defconfig updates for 4.9" from Wei Xu:
- Enable hisilicon SAS and XGE for hip05 and hip06
- Enable drm, powerkey, bluetooth and adv7511/adv7533 for hikey
- Add PINCTRL to HISI platform
* tag 'hisi-defconfig-for-4.9' of git://github.com/hisilicon/linux-hisi:
Kconfig: ARCH_HISI: Add PINCTRL to HISI platform
arm64: defconfig: enable bluetooth supports as modules
arm64: defconfig: enable CONFIG_INPUT_HISI_POWERKEY for HiKey
arm64: defconfig: Enable HiSilicon kirin drm, adv7533 for HiKey
arm64: defconfig: Enable Hisi SAS and HNS
* dt/irq-fix:
arm64: dts: Fix broken architected timer interrupt trigger
This resolves a non-obvious conflict between a bugfix from
v4.8 and a cleanup for the exynos7 platform.
The ARM architected timer specification mandates that the interrupt
associated with each timer is level triggered (which corresponds to
the "counter >= comparator" condition).
A number of DTs are being remarkably creative, declaring the interrupt
to be edge triggered. A quick look at the TRM for the corresponding ARM
CPUs clearly shows that this is wrong, and I've corrected those.
For non-ARM designs (and in the absence of a publicly available TRM),
I've made them active low as well, which can't be completely wrong
as the GIC cannot disinguish between level low and level high.
The respective maintainers are of course welcome to prove me wrong.
While I was at it, I took the liberty to fix a couple of related issue,
such as some spurious affinity bits on ThunderX, and their complete
absence on ls1043a (both of which seem to be related to copy-pasting
from other DTs).
Acked-by: Duc Dang <dhdang@apm.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the nodes for the dwc2 USB controller and the related USB PHYs.
Currently we force usb0 to host mode because OTG is currently not
working in our PHY driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add nodes for i2c bus on gxbb based platforms.
On the OdroidC2 (I2C A) and P200 (I2C B), the pull-up resistor are
present directly on the board. This indicates that these pins are
dedicated to i2c.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This is used to configure the pins of the sd_emmc_a controller to
which an SDIO module is connected (when available).
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Amlogic reference driver uses the "mc_val" devicetree property to
configure the PRG_ETHERNET_ADDR0 register. Unfortunately it uses magic
values for this configuration.
According to the datasheet the PRG_ETHERNET_ADDR0 register is at address
0xc8834108. However, the reference driver uses 0xc8834540 instead.
According to my tests, the value from the reference driver is correct.
No changes are required to the board dts files because the only
required configuration option is the phy-mode, which had to be
configured correctly before as well.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
All of these have a Realtek Gbit RGMII PHY.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
- Add property dma-coherent for ls2080a PCI device to save software
cache maintenance.
- Update serial aliases and use stdout-path to sepecify console for
ls2080a and ls1043a boards.
- Add DDR memory controller device node for ls2080a and ls1043a SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJX1lq1AAoJEFBXWFqHsHzOxA0H/3kkDhBMthlIkFk9BIEytFta
O1U2f6pjjQg+YJIrhZLronqlp3o/cnkhEe16un/cBWk2mBSMbrt9/Mg5CJeUhz/I
AcNAbwwoY0qRgYSgbEoFpZu6AKe8rjrKapPoOGgAWSVBBmPhM448l56PfVz2+DMT
PgTqEkl+flH3ed7DhdL7NLhyYZQ5OanwjAk8K53tDIHSt8OP5ttxbXDNZxv0kUpI
WLyqJkKpLyJm46H4tSjar5XtRSPf12+lz9sLOMdodEodxdofjIFiXHlNDEIwG0Xo
NRYO4wAAWy+4D8VehAkCc64ZUOk5qBbpGZVWTNHjvanvQ1WLON7uroh3xAqZAsE=
=cOOP
-----END PGP SIGNATURE-----
Merge tag 'imx-dt64-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt64
Pull "i.MX arm64 device tree changes for 4.9" from Shawn Guo:
- Add property dma-coherent for ls2080a PCI device to save software
cache maintenance.
- Update serial aliases and use stdout-path to sepecify console for
ls2080a and ls1043a boards.
- Add DDR memory controller device node for ls2080a and ls1043a SoCs.
* tag 'imx-dt64-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: ls2080a: Add 'dma-coherent' for ls2080a PCI nodes
arm64: dts: add stdout-path to chosen node for ls2080a/ls1043a boards
arm64: dts: updates serial aliases for ls1043a rdb and qds boards
arm64: dts: Add DDR memory controller for Layerscape SoCs
Add a couple of devices (AGIC, ADMA) on Tegra210 and enable them on
Smaug. Also enable DPAUX on Smaug to allow the I2C bus that shares pads
with the DPAUX to be used to access various audio devices. Furthermore,
enable the XUSB controller on Smaug for USB 3.0 support.
Finally, select PM_GENERIC_DOMAINS for 64-bit Tegra devices to make sure
devices are probed only after their power partitions have been enabled.
-----BEGIN PGP SIGNATURE-----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=RrBi
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.9-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt64
Pull "arm64: tegra: Device tree changes for v4.9-rc1" from Thierry Reding:
Add a couple of devices (AGIC, ADMA) on Tegra210 and enable them on
Smaug. Also enable DPAUX on Smaug to allow the I2C bus that shares pads
with the DPAUX to be used to access various audio devices. Furthermore,
enable the XUSB controller on Smaug for USB 3.0 support.
Finally, select PM_GENERIC_DOMAINS for 64-bit Tegra devices to make sure
devices are probed only after their power partitions have been enabled.
* tag 'tegra-for-4.9-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Select PM_GENERIC_DOMAINS
arm64: tegra: Enable XUSB controller on Tegra210 Smaug
arm64: tegra: Add the various audio devices for Tegra210 Smaug
arm64: tegra: Enable DPAUX for Tegra210 Smaug
arm64: tegra: Add ACONNECT, ADMA and AGIC nodes Tegra210 Smaug
arm64: tegra: Add SOR power-domain for Tegra210
arm64: tegra: Add ADMA node for Tegra210
arm64: tegra: Add AGIC node for Tegra210
arm64: tegra: Drop clock and reset names for XUSB powergates
arm64: tegra: Simplify Tegra210 GPIO compatible value
Pull "Rockchip dts64 changes for 4.9" from Heiko Stübner:
64bit Rockchip devicetree changes containing support for the recently
added firmware reboot-flag support, one new board the Tronsmart Orion
based on the rk3368 and a large number of newly supported peripherals
for the rk3399 (type-c phy, usb2 phy, pcie controller and pcie phy,
gmac, arm-pmu using ppi partitioning, efuse, saradc) as well as some
smaller housekeeping and non-critical fixes.
* tag 'v4.9-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (22 commits)
arm64: dts: rockchip: add Type-C phy for RK3399
arm64: dts: rockchip: enable the gmac for rk3399 evb board
arm64: dts: rockchip: add the gmac needed node for rk3399
arm64: dts: rockchip: support the pmu node for rk3399
arm64: dts: rockchip: change all interrupts cells to 4 on rk3399 SoCs
arm64: dts: rockchip: add the tcpc for rk3399 power domain
arm64: dts: rockchip: add efuse0 device node for rk3399
arm64: dts: rockchip: configure PCIe support for rk3399-evb
arm64: dts: rockchip: add the PCIe controller support for RK3399
arm64: dts: rockchip: add the PCIe PHY for RK3399
arm64: dts: rockchip: add the gmac power domain on rk3399
arm64: dts: rockchip: Add pinctrl entry for 32k clock on rk3399
arm64: dts: rockchip: set to CCI clock of RK3399 to 600M
arm64: dts: rockchip: fix the address map for WDT0 and WDT1
arm64: dts: rockchip: add the saradc for rk3399
arm64: dts: rockchip: configure usb2-phy support for rk3399-evb
arm64: dts: rockchip: add usb2-phy support for rk3399
arm64: dts: rockchip: add syscon-reboot-mode DT node
soc: rockchip: add reboot-mode header
arm64: dts: rockchip: remove broken-cd from sdio0
...
v4.9, please pull the folllowing:
- Dhanajay adds the PWM Device Tree nodes to the Northstar 2 DTS files
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Gedm
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.9/devicetree-arm64' of http://github.com/Broadcom/stblinux into next/dt64
Pull "Broadcom devicetree-arm64 changes for 4.9" from Florian Fainelli:
This pull request contains Broadcom ARM64-based SoC Device Tree changes for
v4.9, please pull the folllowing:
- Dhanajay adds the PWM Device Tree nodes to the Northstar 2 DTS files
* tag 'arm-soc/for-4.9/devicetree-arm64' of http://github.com/Broadcom/stblinux:
arm64: dts: Add PWM DT node for NS2
- add description for the new Armada 8040 dev board
- add the PIC and PMU on Armada 7K/8K
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlfMQ9EACgkQCwYYjhRyO9UmVwCfZs5WQiOtUhnAc8xc1s1ac+AD
tcoAoKnlIFxvt1QIGqxjfzk3tPtEAj0a
=XbJ5
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.9-1' of git://git.infradead.org/linux-mvebu into next/dt64
Pull "mvebu dt64 for 4.9 (part 1)" from Gregory CLEMENT:
- add description for the new Armada 8040 dev board
- add the PIC and PMU on Armada 7K/8K
* tag 'mvebu-dt64-4.9-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: describe the PIC and PMU on Armada 7K/8K
arm64: dts: marvell: add description for the Armada 8040 dev board
arm64: dts: marvell: add description for the slave CP110 in Armada 8K
* Updates for MSM8916 including TSCR, SMSM/SMP2P, and MBA reserve
* Update SCM node to denote being a reset-controller
* Fix broken interrupt settings
* Add TSENS nodes for MSM8916/MSM8996
* Add DB820c support
* Add MSM8916/APQ8016 display support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O4O+
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt64
Pull "Qualcomm ARM64 Updates for v4.9" from Andy Gross:
* Updates for MSM8916 including TSCR, SMSM/SMP2P, and MBA reserve
* Update SCM node to denote being a reset-controller
* Fix broken interrupt settings
* Add TSENS nodes for MSM8916/MSM8996
* Add DB820c support
* Add MSM8916/APQ8016 display support
* tag 'qcom-arm64-for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: apq8016-sbc: Add HDMI display support
arm64: dts: msm8916: Add display support
arm64: dts: db820c: add support to external sd card.
arm64: dts: db820c: add support to SPI on HS
arm64: dts: db820c: add support to LS-SPI0
arm64: dts: db820c: add support to I2C on HS
arm64: dts: db820c: add support to LS-I2C1
arm64: dts: db820c: add support to LS-I2C0
arm64: dts: db820c: add support to LS-UART0
arm64: dts: db820c: add basic board support
arm64: dts: msm8996: Add thermal zones, tsens and qfprom nodes
arm64: dts: msm8916: Add thermal zones, tsens and qfprom nodes
arm64: dts: qcom: Fix broken interrupt trigger settings
arm64: dts: qcom: msm8916: Add tcsr syscon
arm64: dts: qcom: msm8916: Make scm a reset-controller
arm64: dts: qcom: msm8916: Add mba memory reserve
arm64: dts: qcom: msm8916: Add smsm and smp2p nodes
- Set UART1 clock frequency to 150MHz for higher baud rates on hikey
- Add display subsystem, HDMI and cma nodes on hikey to support display
- Add syscon-reboot-mode support on hikey
- Add pstore support on hikey
- Add resets and sd-uhs-sdr property dwmmc ndoe on hikey
- Remove hip05_hns.dtsi since it can not be built without mbigenv1
- Update system controller bingding document for hip05 and hip06
- Add xge and sas support on hip06
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yhRv
-----END PGP SIGNATURE-----
Merge tag 'hisi-soc-dt-for-4.9' of git://github.com/hisilicon/linux-hisi into next/dt64
Pull "ARM64: DT: Hisilicon SoC DT updates for 4.9" from Wei Xu:
- Set UART1 clock frequency to 150MHz for higher baud rates on hikey
- Add display subsystem, HDMI and cma nodes on hikey to support display
- Add syscon-reboot-mode support on hikey
- Add pstore support on hikey
- Add resets and sd-uhs-sdr property dwmmc ndoe on hikey
- Remove hip05_hns.dtsi since it can not be built without mbigenv1
- Update system controller bingding document for hip05 and hip06
- Add xge and sas support on hip06
* tag 'hisi-soc-dt-for-4.9' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hi6220: add sd-uhs- properties into dwmmc_1
arm64: dts: hi6220: add resets property into dwmmc nodes
arm64: dts: hikey: extend default cma size to 128MB
arm64: dts: hip06: Append sas node
arm64: dts: hip06: Append hns node
dt-bindings: hisilicon: Add Hip05 and Hip06 system controller support
arm64: dts: hip05: kill hip05_hns.dtsi
arm64: dts: hikey: Add pstore support for HiKey
arm64: dts: hikey: Add hikey support for syscon-reboot-mode
arm64: dts: Add HDMI node for hi6220-hikey
arm64: dts: Add display subsystem DT nodes for hi6220-hikey
arm64: dts: set UART1 clock frequency to 150MHz
1. Use human-friendly symbols for interrupt flags.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ILIK
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt64
Pull "Samsung DeviceTree ARM64 update for v4.9" from Krzysztof Kozlowski:
1. Use human-friendly symbols for interrupt flags.
* tag 'samsung-dt64-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Use human-friendly symbols for timer interrupt flags
* Match DT names other projects and documents
* Use clock/reset drivers
* Add new SoC/board support
* Misc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ctoy
-----END PGP SIGNATURE-----
Merge tag 'uniphier-dt64-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt64
Merge "UniPhier ARM64 SoC DT updates for v4.9" from Masahiro Yamada:
* Match DT names other projects and documents
* Use clock/reset drivers
* Add new SoC/board support
* Misc
* tag 'uniphier-dt64-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: add LD11 SoC/Board support
arm64: dts: uniphier: add specific compatible to SoC-Glue node
arm64: dts: uniphier: use clock/reset controllers
arm64: dts: uniphier: add pinctrl property to System Bus node
arm64: dts: uniphier: match DT names to other projects and documents
This commit adds a reference to the appropriate MSI controller in the
description of the PCIe controllers on Marvel Armada 7K and 8K
platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Paul Mackerras writes:
The highlights are:
* Reduced latency for interrupts from PCI pass-through devices, from
Suresh Warrier and me.
* Halt-polling implementation from Suraj Jitindar Singh.
* 64-bit VCPU statistics, also from Suraj.
* Various other minor fixes and improvements.
The AES-CTR glue code avoids calling into the blkcipher API for the
tail portion of the walk, by comparing the remainder of walk.nbytes
modulo AES_BLOCK_SIZE with the residual nbytes, and jumping straight
into the tail processing block if they are equal. This tail processing
block checks whether nbytes != 0, and does nothing otherwise.
However, in case of an allocation failure in the blkcipher layer, we
may enter this code with walk.nbytes == 0, while nbytes > 0. In this
case, we should not dereference the source and destination pointers,
since they may be NULL. So instead of checking for nbytes != 0, check
for (walk.nbytes % AES_BLOCK_SIZE) != 0, which implies the former in
non-error conditions.
Fixes: 49788fe2a1 ("arm64/crypto: AES-ECB/CBC/CTR/XTS using ARMv8 NEON and Crypto Extensions")
Cc: stable@vger.kernel.org
Reported-by: xiakaixu <xiakaixu@huawei.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when running on FVP, CPU 0 boots up with its BPR changed from
the reset value. This renders it impossible to (preemptively) prioritize
interrupts on CPU 0.
This is harmless on normal systems since Linux typically does not
support preemptive interrupts. It does however cause problems in
systems with additional changes (such as patches for NMI simulation).
Many thanks to Andrew Thoelke for suggesting the BPR as having the
potential to harm preemption.
Suggested-by: Andrew Thoelke <andrew.thoelke@arm.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Make use of the new alternative_if and alternative_else_nop_endif and
get rid of our open-coded NOP sleds, making the code simpler to read.
Note that for __kvm_call_hyp the branch to __vhe_hyp_call has been moved
out of the alternative sequence, and in the default case there will be
four additional NOPs executed.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: kvmarm@lists.cs.columbia.edu
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Make use of the new alternative_if and alternative_else_nop_endif and
get rid of our homebew NOP sleds, making the code simpler to read.
Note that for cpu_do_switch_mm the ret has been moved out of the
alternative sequence, and in the default case there will be three
additional NOPs executed.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In some cases, one side of an alternative sequence is simply a number of
NOPs used to balance the other side. Keeping track of this manually is
tedious, and the presence of large chains of NOPs makes the code more
painful to read than necessary.
To ameliorate matters, this patch adds a new alternative_else_nop_endif,
which automatically balances an alternative sequence with a trivial NOP
sled.
In many cases, we would like a NOP-sled in the default case, and
instructions patched in in the presence of a feature. To enable the NOPs
to be generated automatically for this case, this patch also adds a new
alternative_if, and updates alternative_else and alternative_endif to
work with either alternative_if or alternative_endif.
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Martin <dave.martin@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[will: use new nops macro to generate nop sequences]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The LSE atomics are implemented using alternative code sequences of
different lengths, and explicit NOP padding is used to ensure the
patching works correctly.
This patch converts the bulk of the LSE code over to using the __nops
macro, which makes it slightly clearer as to what is going on and also
consolidates all of the padding at the end of the various sequences.
Signed-off-by: Will Deacon <will.deacon@arm.com>
NOP sequences tend to get used for padding out alternative sections
and uarch-specific pipeline flushes in errata workarounds.
This patch adds macros for generating these sequences as both inline
asm blocks, but also as strings suitable for embedding in other asm
blocks directly.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Similar to our {read,write}_sysreg accessors for architected, named
system registers, this patch introduces {read,write}_sysreg_s variants
that can take arbitrary sys_reg output and therefore access IMPDEF
registers or registers that unsupported by binutils.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The ../../../arm... style cross-references added by commit 9d56c22a78
("ARM: bcm2835: Add devicetree for the Raspberry Pi 3.") do not work in the
context of the split device-tree repository[0] (where the directory
structure differs). As with commit 8ee57b8182 ("ARM64: dts: vexpress: Use
a symlink to vexpress-v2m-rs1.dtsi from arch=arm") use symlinks instead.
[0] https://git.kernel.org/cgit/linux/kernel/git/devicetree/devicetree-rebasing.git/
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Lee Jones <lee@kernel.org>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rpi-kernel@lists.infradead.org
Cc: arm@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We've grown our own versions of bug.h, ftrace.h, pci.h and topology.h,
so generating the generic ones as well is unnecessary and a potential
source of build hiccups. At the very least, having them present has
confused my source-indexing tool, and that simply will not do.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Systems with differing CPU i-cache/d-cache line sizes can cause
problems with the cache management by software when the execution
is migrated from one to another. Usually, the application reads
the cache size on a CPU and then uses that length to perform cache
operations. However, if it gets migrated to another CPU with a smaller
cache line size, things could go completely wrong. To prevent such
cases, always use the smallest cache line size among the CPUs. The
kernel CPU feature infrastructure already keeps track of the safe
value for all CPUID registers including CTR. This patch works around
the problem by :
For kernel, dynamically patch the kernel to read the cache size
from the system wide copy of CTR_EL0.
For applications, trap read accesses to CTR_EL0 (by clearing the SCTLR.UCT)
and emulate the mrs instruction to return the system wide safe value
of CTR_EL0.
For faster access (i.e, avoiding to lookup the system wide value of CTR_EL0
via read_system_reg), we keep track of the pointer to table entry for
CTR_EL0 in the CPU feature infrastructure.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Right now we trap some of the user space data cache operations
based on a few Errata (ARM 819472, 826319, 827319 and 824069).
We need to trap userspace access to CTR_EL0, if we detect mismatched
cache line size. Since both these traps share the EC, refactor
the handler a little bit to make it a bit more reader friendly.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
On systems with mismatched i/d cache min line sizes, we need to use
the smallest size possible across all CPUs. This will be done by fetching
the system wide safe value from CPU feature infrastructure.
However the some special users(e.g kexec, hibernate) would need the line
size on the CPU (rather than the system wide), when either the system
wide feature may not be accessible or it is guranteed that the caller
executes with a gurantee of no migration.
Provide another helper which will fetch cache line size on the current CPU.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: James Morse <james.morse@arm.com>
Reviewed-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
adrp uses PC-relative address offset to a page (of 4K size) of
a symbol. If it appears in an alternative code patched in, we
should adjust the offset to reflect the address where it will
be run from. This patch adds support for fixing the offset
for adrp instructions.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Adds helpers for decoding/encoding the PC relative addresses for adrp.
This will be used for handling dynamic patching of 'adrp' instructions
in alternative code patching.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The alternative code patching doesn't check if the replaced instruction
uses a pc relative literal. This could cause silent corruption in the
instruction stream as the instruction will be executed from a different
address than what it was compiled for. Catch all such cases.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Suggested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Right now we run through the work around checks on a CPU
from __cpuinfo_store_cpu. There are some problems with that:
1) We initialise the system wide CPU feature registers only after the
Boot CPU updates its cpuinfo. Now, if a work around depends on the
variance of a CPU ID feature (e.g, check for Cache Line size mismatch),
we have no way of performing it cleanly for the boot CPU.
2) It is out of place, invoked from __cpuinfo_store_cpu() in cpuinfo.c. It
is not an obvious place for that.
This patch rearranges the CPU specific capability(aka work around) checks.
1) At the moment we use verify_local_cpu_capabilities() to check if a new
CPU has all the system advertised features. Use this for the secondary CPUs
to perform the work around check. For that we rename
verify_local_cpu_capabilities() => check_local_cpu_capabilities()
which:
If the system wide capabilities haven't been initialised (i.e, the CPU
is activated at the boot), update the system wide detected work arounds.
Otherwise (i.e a CPU hotplugged in later) verify that this CPU conforms to the
system wide capabilities.
2) Boot CPU updates the work arounds from smp_prepare_boot_cpu() after we have
initialised the system wide CPU feature values.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This is a cosmetic change to rename the functions dealing with
the errata work arounds to be more consistent with their naming.
1) check_local_cpu_errata() => update_cpu_errata_workarounds()
check_local_cpu_errata() actually updates the system's errata work
arounds. So rename it to reflect the same.
2) verify_local_cpu_errata() => verify_local_cpu_errata_workarounds()
Use errata_workarounds instead of _errata.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Right now we use 0 as the safe value for CTR_EL0:L1Ip, which is
not defined at the moment. The safer value for the L1Ip should be
the weakest of the policies, which happens to be AIVIVT. While at it,
fix the comment about safe_val.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
1. Remove the old binding code.
2. Read the nid of cpu0 from dts.
3. Fallback the nid of cpu0 to 0 when numa=off is set in bootargs.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When the deleted code is executed, only the bit of cpu0 was set on
cpu_possible_mask. So that, only set_cpu_numa_node(0, NUMA_NO_NODE); will
be executed. And map_cpu_to_node(0, 0) will soon be called. So these code
can be safely removed.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
To make each percpu area allocated from its local numa node. Without this
patch, all percpu areas will be allocated from the node which cpu0 belongs
to.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Use pr_fmt to prefix kernel output, and remove duplicated msg
of NUMA turned off.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
numa_init may return error because of numa configuration error. So "No
NUMA configuration found" is inaccurate. In fact, specific configuration
error information should be immediately printed by the testing branch.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
By using a common attr_groups array, the common arm_pmu code can set up
common files (e.g. cpumask) for us in subsequent patches.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When debug preempt or preempt tracer is enabled, preempt_count_add/sub()
can be traced by function and function graph tracing, and
preempt_disable/enable() would call preempt_count_add/sub(), so in Ftrace
subsystem we should use preempt_disable/enable_notrace instead.
In the commit 345ddcc882 ("ftrace: Have set_ftrace_pid use the bitmap
like events do") the function this_cpu_read() was added to
trace_graph_entry(), and if this_cpu_read() calls preempt_disable(), graph
tracer will go into a recursive loop, even if the tracing_on is
disabled.
So this patch change to use preempt_enable/disable_notrace instead in
this_cpu_read().
Since Yonghui Yang helped a lot to find the root cause of this problem,
so also add his SOB.
Signed-off-by: Yonghui Yang <mark.yang@spreadtrum.com>
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
smp_mb__before_spinlock() is intended to upgrade a spin_lock() operation
to a full barrier, such that prior stores are ordered with respect to
loads and stores occuring inside the critical section.
Unfortunately, the core code defines the barrier as smp_wmb(), which
is insufficient to provide the required ordering guarantees when used in
conjunction with our load-acquire-based spinlock implementation.
This patch overrides the arm64 definition of smp_mb__before_spinlock()
to map to a full smp_mb().
Cc: <stable@vger.kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When CONFIG_PID_IN_CONTEXTIDR is not selected, we use an empty stub
definition of contextidr_thread_switch(). As everything we rely upon
exists regardless of CONFIG_PID_IN_CONTEXTIDR, we don't strictly require
an empty stub.
By using IS_ENABLED() rather than ifdeffery, we avoid duplication, and
get compiler coverage on all the code even when CONFIG_PID_IN_CONTEXTIDR
is not selected and the code is optimised away.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
A while back we added {read,write}_sysreg accessors to handle accesses
to system registers, without the usual boilerplate asm volatile,
temporary variable, etc.
This patch makes use of these across arm64 to make code shorter and
clearer. For sequences with a trailing ISB, the existing isb() macro is
also used so that asm blocks can be removed entirely.
A few uses of inline assembly for msr/mrs are left as-is. Those
manipulating sp_el0 for the current thread_info value have special
clobber requiremends.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
A while back we added {read,write}_sysreg accessors to handle accesses
to system registers, without the usual boilerplate asm volatile,
temporary variable, etc.
This patch makes use of these in the arm64 KVM code to make the code
shorter and clearer.
At the same time, a comment style violation next to a system register
access is fixed up in reset_pmcr, and comments describing whether
operations are reads or writes are removed as this is now painfully
obvious.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
A while back we added {read,write}_sysreg accessors to handle accesses
to system registers, without the usual boilerplate asm volatile,
temporary variable, etc.
This patch makes use of these in the arm64 DCC accessors to make the
code shorter and clearer.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
A while back we added {read,write}_sysreg accessors to handle accesses
to system registers, without the usual boilerplate asm volatile,
temporary variable, etc.
This patch makes use of these in the arm64 arch timer accessors to make
the code shorter and clearer.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently write_sysreg has to allocate a temporary register to write
zero to a system register, which is unfortunate given that the MSR
instruction accepts XZR as an operand.
Allow XZR to be used when appropriate by fiddling with the assembly
constraints.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The 'dma-coherent' indicates that the hardware IP block can ensure
the coherency of the data transferred from/to the IP block. This
can avoid the software cache flush/invalid actions, and improve
the performance significantly.
The PCI IP block of ls2080a has this capability, so adding this
feature to improve the PCI performance.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- lazy enablement of runtime instrumentation
- up to 255 CPUs for nested guests
- rework of machine check deliver
- cleanups/fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=99TB
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: features and fixes for 4.9
- lazy enablement of runtime instrumentation
- up to 255 CPUs for nested guests
- rework of machine check deliver
- cleanups/fixes
If, when proxying a GICV access at EL2, we detect that the guest is
doing something silly, report an EL1 SError instead ofgnoring the
access.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
If EL1 generates an asynchronous abort and then traps into EL2
before the abort has been delivered, we may end-up with the
abort firing at the worse possible place: on the host.
In order to avoid this, it is necessary to take the abort at EL2,
by clearing the PSTATE.A bit. In order to survive this abort,
we do it at a point where we're in a known state with respect
to the world switch, and handle the resulting exception,
overloading the exit code in the process.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
If we have caught an SError whilst exiting, we've tagged the
exit code with the pending information. In that case, let's
re-inject the error into the guest, after having adjusted
the PC if required.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Similarily to EL1, an asynchronous abort can be triggered whilst
running at EL2. But instead of making that a new error code,
we need to communicate it to the rest of KVM together with
the exit reason. So let's hijack a single bit that allows the
exception code to be tagged with a "pending SError" information.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
As we now have some basic handling to EL1-triggered aborts, we can
actually report them to KVM.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
If we've exited the guest because it has triggered an asynchronous
abort from EL1, a possible course of action is to let it know it
screwed up by giving it a Virtual Abort to chew on.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
So far, we don't have a code to indicate that we've taken an
asynchronous abort from EL1. Let's add one.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Now that we're able to context switch the HCR_EL2.VA bit, let's
introduce a helper that injects an Abort into a vcpu.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The HCR_EL2.VSE bit is used to signal an SError to a guest, and has
the peculiar feature of getting cleared when the guest has taken
the abort (this is the only bit that behaves as such in this register).
This means that if we signal such an abort, we must leave it
in the guest context until it disappears from HCR_EL2, and at which
point it must be cleared from the context. This is achieved by
reading back from HCR_EL2 until the guest takes the fault.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
HCR_VA is a leftover from ARMv7, On ARMv8, this is HCR_VSE
(which stands for Virtual System Error), and has better
defined semantics.
Let's rename the constant.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
In order to efficiently perform the GICV access on behalf of the
guest, we need to be able to avoid going back all the way to
the host kernel.
For this, we introduce a new hook in the world switch code,
conveniently placed just after populating the fault info.
At that point, we only have saved/restored the GP registers,
and we can quickly perform all the required checks (data abort,
translation fault, valid faulting syndrome, not an external
abort, not a PTW).
Coming back from the emulation code, we need to skip the emulated
instruction. This involves an additional bit of save/restore in
order to be able to access the guest's PC (and possibly CPSR if
this is a 32bit guest).
At this stage, no emulation code is provided.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
It would make some sense to share the conditional execution code
between 32 and 64bit. In order to achieve this, let's move that
code to virt/kvm/arm/aarch32.c. While we're at it, drop a
superfluous BUG_ON() that wasn't that useful.
Following patches will migrate the 32bit port to that code base.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
In order to make emulate.c more generic, move the arch-specific
manupulation bits out of emulate.c.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
SCTLR_EL2.SPAN bit controls what happens with the PSTATE.PAN bit on an
exception. However, this bit has no effect on the PSTATE.PAN when
HCR_EL2.E2H or HCR_EL2.TGE is unset. Thus when VHE is used and
exception taken from a guest PSTATE.PAN bit left unchanged and we
continue with a value guest has set.
To address that always reset PSTATE.PAN on entry from EL1.
Fixes: 1f364c8c48 ("arm64: VHE: Add support for running Linux in EL2 mode")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
When rewriting the assembly code to C code, it was useful to have
exported aliases or static functions so that we could keep the existing
common C code unmodified and at the same time rewrite arm64 from
assembly to C code, and later do the arm part.
Now when both are done, we really don't need this level of indirection
anymore, and it's time to save a few lines and brain cells.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Now that 32-bit KVM no longer performs cache maintenance for page table
updates, we no longer need empty stubs for arm64. Remove them.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: kvmarm@lists.cs.columbia.edu
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
We are doing an unnecessary stack push/pop operation when restoring
the guest registers x0-x18 in __guest_enter(). This patch saves the
two instructions by using x18 as a base register. No need to store
the vcpu context pointer in stack because it is redundant, the same
information is available in tpidr_el2. The function __guest_exit()
calling convention is slightly modified, caller only pushes the regs
x0-x1 to stack instead of regs x0-x3.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
When zeroing an I/O location, the current accessors are forced to
allocate a temporary register to store the zero for the write. By
tweaking the assembly constraints, we can allow the compiler to use
the zero register directly in such cases, and save some juggling.
Compiling a representative kernel configuration with GCC 6 shows
that 2.3KB worth of code can be wasted just on that!
text data bss dec hex filename
13316776 3248256 18176769 34741801 2121e29 vmlinux.o.new
13319140 3248256 18176769 34744165 2122765 vmlinux.o.old
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This supports GPIO leds on H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports SSI sound for H3ULCB board.
SSI DMA mode used. CS2000 used as AUDIO_CLK_B.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports GPIO keys on H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove cap-mmc-highspeed property from SDHI2 and SDHI3.
This property is unnecessary as the driver automatically sets
the highspeed capability. Furthermore its use is inconsistent with SDHI0
and SDHI1 which are also highspeed capable but do not have this property
present.
Found by inspection.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
vms and vcpus have statistics associated with them which can be viewed
within the debugfs. Currently it is assumed within the vcpu_stat_get() and
vm_stat_get() functions that all of these statistics are represented as
u32s, however the next patch adds some u64 vcpu statistics.
Change all vcpu statistics to u64 and modify vcpu_stat_get() accordingly.
Since vcpu statistics are per vcpu, they will only be updated by a single
vcpu at a time so this shouldn't present a problem on 32-bit machines
which can't atomically increment 64-bit numbers. However vm statistics
could potentially be updated by multiple vcpus from that vm at a time.
To avoid the overhead of atomics make all vm statistics ulong such that
they are 64-bit on 64-bit systems where they can be atomically incremented
and are 32-bit on 32-bit systems which may not be able to atomically
increment 64-bit numbers. Modify vm_stat_get() to expect ulongs.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: David Matlack <dmatlack@google.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
There are 2 Type-C phy on RK3399, they are almost same, except the
address of register. They support USB3.0 Type-C and DisplayPort1.3
Alt Mode on USB Type-C. Register a phy, supply it to USB3 controller
and DP controller.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We add the required and optional properties for evb board.
See the [0] to get the detail information.
[0]:
Documentation/devicetree/bindings/net/rockchip-dwmac.txt
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The RK3399 GMAC Ethernet Controller provides a complete Ethernet interface
from processor to a Reduced Media Independent Interface (RMII) and Reduced
Gigabit Media Independent Interface (RGMII) compliant Ethernet PHY.
This patch adds the related needed device information.
e.g.: interrupts, grf, clocks, pinctrl and so on.
The full details are in [0].
[0]:
Documentation/devicetree/bindings/net/rockchip-dwmac.txt
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds static keys transparently for all the cpu_hwcaps
features by implementing an array of default-false static keys and
enabling them when detected. The cpus_have_cap() check uses the static
keys if the feature being checked is a constant, otherwise the compiler
generates the bitmap test.
Because of the early call to static_branch_enable() via
check_local_cpu_errata() -> update_cpu_capabilities(), the jump labels
are initialised in cpuinfo_store_boot_cpu().
Cc: Will Deacon <will.deacon@arm.com>
Cc: Suzuki K. Poulose <Suzuki.Poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
There is only fixup_init() in mm.h , and it is only called
in free_initmem(), so move the codes from fixup_init() into
free_initmem(), then drop fixup_init() and mm.h.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This supports watchdog timer for H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This enables EXTALR clock that can be used for the watchdog.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports I2C2 bus on H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports Ethernet AVB on H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This enables the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A7795 SoC based H3ULCB low cost
board.
This commit supports the following peripherals:
- SCIF (console)
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The audio-dmac nodes used the generic compatible property only.
Add the SoC-specific one, to make it future proof.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Only the VGA output is supported for now.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the DU device to r8a7795.dtsi in a disabled state.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a7795 has 9 VSP instances.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The FCPs handle the interface between various IP cores and memory. Add
the instances related to the VSP2s.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We have to set SW15 to pin 2-3 side on the board before we use CN9
as USB host or peripheral.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch also adds a regulator node for USB2.0 to handle VBUS on/off
by the phy-rcar-gen3-usb2 driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the upper limit otherwise the driver cannot utilize max speeds.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Provide nodes for the FCP devices dedicated to the FDP device channels.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds to enable the ARM Performance Monitor Units for rk3399.
ARM cores often have a PMU for counting cpu and cache events like cache
misses and hits.
This uses the new interrupt-partition mechanism to allow the two pmu
instances to use the per-cpu interrupt.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the interrupts cells value for 4, and the 4th cell is zero.
Due to the doc[0] said:" the system requires describing PPI affinity,
then the value must be at least 4"
The 4th cell is a phandle to a node describing a set of CPUs this
interrupt is affine to. The interrupt must be a PPI, and the node
pointed must be a subnode of the "ppi-partitions" subnode. For
interrupt types other than PPI or PPIs that are not partitionned,
this cell must be zero. See the "ppi-partitions" node description
below.
[0]:
Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Currently, enabling stacktrace of a kprobe events generates warning:
echo stacktrace > /sys/kernel/debug/tracing/trace_options
echo "p xhci_irq" > /sys/kernel/debug/tracing/kprobe_events
echo 1 > /sys/kernel/debug/tracing/events/kprobes/enable
save_stack_trace_regs() not implemented yet.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 0 at ../kernel/stacktrace.c:74 save_stack_trace_regs+0x3c/0x48
Modules linked in:
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.8.0-rc4-dirty #5128
Hardware name: ARM Juno development board (r1) (DT)
task: ffff800975dd1900 task.stack: ffff800975ddc000
PC is at save_stack_trace_regs+0x3c/0x48
LR is at save_stack_trace_regs+0x3c/0x48
pc : [<ffff000008126c64>] lr : [<ffff000008126c64>] pstate: 600003c5
sp : ffff80097ef52c00
Call trace:
save_stack_trace_regs+0x3c/0x48
__ftrace_trace_stack+0x168/0x208
trace_buffer_unlock_commit_regs+0x5c/0x7c
kprobe_trace_func+0x308/0x3d8
kprobe_dispatcher+0x58/0x60
kprobe_breakpoint_handler+0xbc/0x18c
brk_handler+0x50/0x90
do_debug_exception+0x50/0xbc
This patch implements save_stack_trace_regs(), so that stacktrace of a
kprobe events can be obtained.
After this patch, there is no warning and we can see the stacktrace for
kprobe events in trace buffer.
more /sys/kernel/debug/tracing/trace
<idle>-0 [004] d.h. 1356.000496: p_xhci_irq_0:(xhci_irq+0x0/0x9ac)
<idle>-0 [004] d.h. 1356.000497: <stack trace>
=> xhci_irq
=> __handle_irq_event_percpu
=> handle_irq_event_percpu
=> handle_irq_event
=> handle_fasteoi_irq
=> generic_handle_irq
=> __handle_domain_irq
=> gic_handle_irq
=> el1_irq
=> arch_cpu_idle
=> default_idle_call
=> cpu_startup_entry
=> secondary_start_kernel
=>
Tested-by: David A. Long <dave.long@linaro.org>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit b5fe242972 ("arm64: kernel: fix style issues in sleep.S")
changed the linkage of _cpu_resume() to local, even though the symbol
is also referenced from hibernate.c. So revert this change.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The code that provides /dev/mem uses xlate_dev_mem_{k,}ptr() to
avoid making a cachable mapping of a non-cachable area on ia64.
On arm64 we do this via phys_mem_access_prot() instead, but provide
dummy versions of xlate_dev_mem_{k,}ptr().
These are the same as those in asm-generic/io.h, which we include from
asm/io.h
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The tcpc is the Type C Port Controller and Type C Port Delivery (tcpd)
is part of it, we haven't used them now, add it to save power consumption.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Here are a number of small fixes for staging and IIO drivers that
resolve reported problems.
Full details are in the shortlog. All of these have been in linux-next
with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlfK4HoPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspt0MAn0wC
dYhZOUHxOptLiEkVGXFCU9kzAJ4gETEbuGn9lgp2TFATOOAN7oqPUw==
=6MKk
-----END PGP SIGNATURE-----
Merge tag 'staging-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver fixes from Greg KH:
"Here are a number of small fixes for staging and IIO drivers that
resolve reported problems.
Full details are in the shortlog. All of these have been in
linux-next with no reported issues"
* tag 'staging-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (35 commits)
arm: dts: rockchip: add reset node for the exist saradc SoCs
arm64: dts: rockchip: add reset saradc node for rk3368 SoCs
iio: adc: rockchip_saradc: reset saradc controller before programming it
iio: accel: kxsd9: Fix raw read return
iio: adc: ti_am335x_adc: Increase timeout value waiting for ADC sample
iio: adc: ti_am335x_adc: Protect FIFO1 from concurrent access
include/linux: fix excess fence.h kernel-doc notation
staging: wilc1000: correctly check if associatedsta has not been found
staging: wilc1000: NULL dereference on error
staging: wilc1000: txq_event: Fix coding error
MAINTAINERS: Add file patterns for ion device tree bindings
MAINTAINERS: Update maintainer entry for wilc1000
iio: chemical: atlas-ph-sensor: fix typo in val assignment
iio: fix sched WARNING "do not call blocking ops when !TASK_RUNNING"
staging: comedi: ni_mio_common: fix AO inttrig backwards compatibility
staging: comedi: dt2811: fix a precedence bug
staging: comedi: adv_pci1760: Do not return EINVAL for CMDF_ROUND_DOWN.
staging: comedi: ni_mio_common: fix wrong insn_write handler
staging: comedi: comedi_test: fix timer race conditions
staging: comedi: daqboard2000: bug fix board type matching code
...
Changes to make the resume from cpu_suspend() code behave more like
secondary boot caused debug exceptions to be unmasked early by
__cpu_setup(). We then go on to restore mdscr_el1 in cpu_do_resume(),
potentially taking break or watch points based on uninitialised registers.
Mask debug exceptions in cpu_do_resume(), which is specific to resume
from cpu_suspend(). Debug exceptions will be restored to their original
state by local_dbg_restore() in cpu_suspend(), which runs after
hw_breakpoint_restore() has re-initialised the other registers.
Reported-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Fixes: cabe1c81ea ("arm64: Change cpu_resume() to enable mmu early then access sleep_sp by va")
Cc: <stable@vger.kernel.org> # 4.7+
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Single-step traps to userspace (e.g. via ptrace) are expected to use
the TRAP_TRACE for the si_code field of the siginfo, as opposed to
TRAP_HWBRPT that we report currently.
Fix the reported value, which has no effect on existing and legacy
builds of GDB.
Reported-by: Yao Qi <yao.qi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add a efuse0 node in the device tree for the ARM64 rk3399 SoC.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Let's assigne slot numbers, ep-gpios and clkreq used by PCIe
on evb board as well the PHY node here. Note that we still
disable them as the auto training of PCIe link will make the
kernel use more time to boot if there are no any devices there.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch introduces PCIe support found on RK3399 platform,
and specify phys phandle for it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds PCIe node for RK3399 to support
PCIe controller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds the gmac ppower-domain to save power consumption
by letting the driver core handle the power-domain so we can
save power on boards not needing Ethernet.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
On some rk3399 boards GPIO0_A0 is hooked up to a 32 kHz clock. This can
be used as the source for various clocks in the system.
Add a pinmux so boards can get this pin properly configured.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Now that the only remaining occurrences of the use of callee saved
registers are on the primary boot path, add a comment to the code
which register is used for what.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Instead of stashing the value of the link register in x28 before setting
up the stack and calling into C code, create an ordinary PCS compatible
stack frame so that we can push the return address onto the stack.
Since exception handlers require a stack as well, assign the stack pointer
register before installing the vector table.
Note that this accounts for the difference between THREAD_START_SP and
THREAD_SIZE, given that the stack pointer is always decremented before
calling into any C code.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Keeping __PHYS_OFFSET in x24 is actually less clear than simply taking
the value of __PHYS_OFFSET using an adrp instruction in the three places
that we need it. So change that.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Using x27 for passing to __enable_mmu what is essentially the return
address makes the code look more complicated than it needs to be. So
switch to x30/lr, and update the secondary and cpu_resume call sites to
simply call __enable_mmu as an ordinary function, with a bl instruction.
This requires the callers to be covered by .idmap.text.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The KASLR processing is only used by the primary boot path, and
complements the processing that takes place in __primary_switch().
Move the two parts together, to make the code easier to understand.
Also, fix up a minor whitespace issue.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: fixed conflict with -rc3 due to lack of fd363bd417]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The function el2_setup() passes its return value in register w20, and
in the two cases where the caller actually cares about this return value,
it is passed into set_cpu_boot_mode_flag() [almost] directly, which
expects its input in w20 as well.
So there is no reason to use a 'special' callee saved register here, but
we can simply follow the PCS for return value and first argument,
respectively.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This fixes a number of style issues in sleep.S. No functional changes are
intended:
- replace absolute literal references with relative references in
__cpu_suspend_enter(), which executes from its virtual address
- replace explicit lr assignment plus branch with bl in cpu_resume(), which
aligns it with stext() and secondary_startup()
- don't export _cpu_resume()
- use adr_l for mpidr_hash reference, and fix the incorrect accompanying
comment, which has been out of date since commit cabe1c81ea ("arm64:
Change cpu_resume() to enable mmu early then access sleep_sp by va")
- replace leading spaces with tabs, and add a bit of whitespace for
readability
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
With these properties added, sd cards inserted into hikey can work at UHS
mode if they have such capability.
Note, this depends on HiKey UHS-SD support patch [1] to work properly.
If you didn't add this patch, but added sd-uhs- properties into dwmmc_1,
then sd cards cannot work. As of this post, patch [1] has been integrated
into maintainer's next branch [2].
[1]: [V4] mmc: dw_mmc-k3: UHS-SD card for Hisilicon Hikey,
https://patchwork.kernel.org/patch/9262515/
[2]: https://git.linaro.org/people/ulf.hansson/mmc.git next
commit a8a5b2909cfc ("mmc: dw_mmc: k3: UHS-SD card for Hisilicon Hikey")
cc: Ulf Hansson <ulf.hansson@linaro.org>
cc: Jaehoon Chung <jh80.chung@samsung.com>
cc: Jinguojun <kid.jin@hisilicon.com>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Add the NVMEM device node in the DTSI.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
[khilman: dropped driver cleanup hunk]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the secure monitor node in the Amlogic Meson GXBB DTSI file to
enable it.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the Infrared Remote Controller on boards which have an Infrared
receiver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the Infrared Remote Controller node so boards with an IR
remote can simply enable it.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the AO clock controller node for the AmLogic GXBB SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Commit e19a6ee246 ("arm64: kernel: Save and restore UAO and
addr_limit on exception entry") states that exception handler inherits
the original PSTATE.UAO value, so UAO needes to be reset
explicitly. However, ARM 8.2 Extension documentation says:
PSTATE.UAO is copied to SPSR_ELx.UAO and is then set to 0 on an
exception taken from AArch64 to AArch64
so hardware already does the right thing.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This allows use of the SDHI SD/SDIO controller present on R-Car Gen3 SoCs
and already enabled in the DT of the r8a7795/salvator-x (H3).
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The arm64 debug monitor initialisation code uses a CPU hotplug notifier
to clear the OS lock when CPUs come online.
This patch converts the code to the new hotplug mechanism.
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The arm64 hw_breakpoint implementation uses a CPU hotplug notifier to
reset the {break,watch}point registers when CPUs come online.
This patch converts the code to the new hotplug mechanism, whilst moving
the invocation earlier to remove the need to disable IRQs explicitly in
the driver (which could cause havok if we trip a watchpoint in an IRQ
handler whilst restoring the debug register state).
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When TIF_SINGLESTEP is set for a task, the single-step state machine is
enabled and we must take care not to reset it to the active-not-pending
state if it is already in the active-pending state.
Unfortunately, that's exactly what user_enable_single_step does, by
unconditionally setting the SS bit in the SPSR for the current task.
This causes failures in the GDB testsuite, where GDB ends up missing
expected step traps if the instruction being stepped generates another
trap, e.g. PTRACE_EVENT_FORK from an SVC instruction.
This patch fixes the problem by preserving the current state of the
stepping state machine when TIF_SINGLESTEP is set on the current thread.
Cc: <stable@vger.kernel.org>
Reported-by: Yao Qi <yao.qi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Expose the arm64_ftr_reg struct covering CTR_EL0 outside of cpufeature.o
so that other code can refer to it directly (i.e., without performing the
binary search)
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Constify the arm64_ftr_regs array, by moving the mutable arm64_ftr_reg
fields out of the array itself. This also streamlines the bsearch, since
the entire array can be covered by fewer cachelines. Moving the payload
out of the array also allows us to have special explicitly defined
struct instance in case other code needs to refer to it directly.
Note that this replaces the runtime sorting of the array with a runtime
BUG() check whether the array is sorted correctly in the code.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The arm64_ftr_bits structures are never modified, so make them read-only.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The UDBG_UNDEFINED/SYSCALL/BADABORT/SEGV are only used to show
verbose user fault messages in arm, not arm64, drop them.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Any arm64 based parts that have cache aliasing issues can set it
manually. Apparently dragged in from ARM(32) defaults in commit
8c2c3df "arm64: Build infrastructure".
Signed-off-by: Kim Phillips <kim.phillips@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The make rpm target depends on proper UTS_MACHINE definition. Also, use
the variable in arch/arm64/kernel/setup.c, so that it's not accidentally
removed in the future.
Reported-and-tested-by: Fabian Vogt <fvogt@suse.com>
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
