The SMPS feature is defined in the specification only to be
used by non-AP stations and not by APs, so remove the support
for changing the AP's SMPS mode dynamically.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-20-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
According to IEEE802.11 specifications the SM power save field
in the HT capability IE and the HE extended capability IE is valid
only in (re)association frames and should be ignored otherwise.
Remove code paths that handled this also for non AP modes.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-17-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An AP that operates on 6GHz may respond with a broadcast probe response.
Don't ignore such frames.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-14-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of HE, the RX NSS is taken from the HE capabilities.
If the supported NSS capabilities that are reported by AP for
HE mode in the HE Capabilities element are different from the NSS
capabilities that are reported by AP for the VHT mode in the VHT
Capabilities element, use the lowest supported NSS to not get all
the values confused.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-9-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set the station bandwidth in HE capability parsing and from
HE capability as the HT/VHT information will not be present
on the 6 GHz band.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-5-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should not include the supported channels element if we have
(advertise) support for extended channel switching. To avoid any
interop issues because we always added it in the past, obey this
restriction only in the (new) 6 GHz band.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131113111.893106-1-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Disable HE if the beacon does not contain an HE operation IE.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-16-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function always returns 0, so there's no point in returning int.
Make it void and remove the impossible error-path when calling it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-11-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set ndev->hw_features as well as ndev->features to allow
changing the TX-related features with ethtool.
We cannot (yet) change RX-related features since that
requires telling the driver about it and we have no API
for that yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-10-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The wireless device might be capable to connect HE
as well as the AP. However, the regulatory domain might
forbid it. Check whether the regulatory domain allows HE connection
when considering if HE IE should be added.
Also, add it when setting our peer capability.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-8-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code was really ugly, refactor it a bit to make it more
readable.
While at it, use sizeof() and fix the UORA element length
check bug.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-4-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check early on that a device has support for QoS (at least 4
queues) when it supports HT/VHT/HE, so we don't have to check
this while connecting.
This lets us clean up the code there: move some of it into
channel preparation to clean up a bit more, and then change
the logic to only check the "wmm_used" flag.
Additionally, disable HE consistently when VHT is disabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-3-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit ab4dfa2053 ("cfg80211: Allow drivers to advertise supported AKM
suites") introduces the support to advertize supported AKMs to userspace.
This needs an enhancement to advertize the AKM support per interface type,
specifically for the cfg80211-based drivers that implement SME and use
different mechanisms to support the AKM's for each interface type (e.g.,
the support for SAE, OWE AKM's take different paths for such drivers on
STA/AP mode).
This commit aims the same and enhances the earlier mechanism of advertizing
the AKMs per wiphy. Add new nl80211 attributes and data structure to
provide supported AKMs per interface type to userspace.
the AKMs advertized in akm_suites are default capabilities if not
advertized for a specific interface type in iftype_akm_suites.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Link: https://lore.kernel.org/r/20200126203032.21934-1-vjakkam@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The regulatory domain might forbid HE operation. Certain regulatory
domains may restrict it for specific channels whereas others may do it
for the whole regulatory domain.
Add an option to indicate it in the channel flag.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200121081213.733757-1-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The 802.11 encapsulation returned early when setting up the keys in case
offloading was enabled. This causes ieee802.11w to not work anymore. Fix
this by moving the check for offloading into the switch/case construct and
allowing CCMP/GCMP keys. With this patch applied ieee80211w works again
when enabling offloading.
Fixes: 50ff477a86 ("mac80211: add 802.11 encapsulation offloading support")
Reported-by: Maharaja Kennadyrajan <mkenna@qti.qualcomm.com>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20200203122812.18993-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
commit 08a5bdde38 ("mac80211: consider QoS Null frames for STA_NULLFUNC_ACKED")
Fixed a bug where we failed to take into account a
nullfunc frame can be either non-QoS or QoS. It turns out
there is at least one more bug in
ieee80211_sta_tx_notify(), introduced in
commit 7b6ddeaf27 ("mac80211: use QoS NDP for AP probing"),
where we forgot to check for the QoS variant and so
assumed the QoS nullfunc frame never went out
Fix this by adding a helper ieee80211_is_any_nullfunc()
which consolidates the check for non-QoS and QoS nullfunc
frames. Replace existing compound conditionals and add a
couple more missing checks for QoS variant.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200114055940.18502-3-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Advertise the correct flags to mac80211 to indicate PS
trigger frames and frame buffering should be handled by
mac80211. This means mac80211_hwsim will now also have to
release buffered multicast frames after a (DTIM) beacon.
Leave STA power save disabled by default since it causes
several p2p, scanning, and rrm hostap tests to fail.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200114055940.18502-2-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Before this patch, frames which where successfully transmitted without
requiring acks where accounted as lost frames.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20191218142736.15843-1-markus.theil@tu-ilmenau.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is now possible to propagate BSS color settings into the subsystem. Lets
make mac80211 also handle them so that we can send them further down the
stack into the drivers. We drop the old bss_color field and change iwlwifi
to use the new he_bss_color struct.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20191217141921.8114-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds the attributes, policy and parsing code to allow userland
to send the info about the BSS coloring settings to the kernel.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20191217141921.8114-1-john@phrozen.org
[johannes: remove the strict policy parsing, that was a misunderstanding]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is too low, at least ETSI regulatory domain would
allow 36 dBm on 5 GHz in (some? most?) cases. But there's
no reason hwsim should have a limit at all, so remove it.
See also
https://lore.kernel.org/r/20191108152013.13418-1-ramonreisfontes@gmail.com
Change-Id: I6edf81d2e82bc8ce7baa40bfc0f210b7b56ef275
Reported-by: Ramon Fontes <ramonreisfontes@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Improve airtime_flags debugfs handler readability reporting configured
airtime flags in both numeric and human readable manner
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/9df7e40b45e95bb0b320317831455beaed1ee3ee.1574872357.git.lorenzo@kernel.org
[remove AQL since it's no longer there]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2019-12-31
This series contains updates to e1000e, igb and igc only.
Robert Beckett provide an igb change to assist in keeping packets from
being dropped due to receive descriptor ring being full when receive
flow control is enabled. Create a separate function to setup SRRCTL to
ease in reuse and ensure that setting of the drop enable bit only if
receive flow control is not enabled.
Sasha adds support for scatter gather support in igc. Improve the
direct memory address mapping flow by optimizing/simplifying and more
clear. Update igc to use pci_release_mem_regions() instead of
pci_release_selected_regions(). Clean up function header comments to
align with the actual code. Adds support for 64 bit DMA access, to help
handle socket buffer fragments in high memory. Adds legacy power
management support in igc by implementing suspend, resume,
runtime_suspend/resume, and runtime_idle callbacks. Clean up references
to Serdes interface in igc since that interface is not supported for
i225 devices.
Alex replaces the pr_info calls with netdev_info in all cases related to
netdev link state, as suggested by Joe Perches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Serdes interface is not applicable for i225 devices.
Remove this from comments and make comments more clearly.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace the pr_info calls with netdev_info in all cases related to the
netdevice link state.
As a result of this patch the link messages will change as shown below.
Before:
e1000e: ens3 NIC Link is Down
e1000e: ens3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
After:
e1000e 0000:00:03.0 ens3: NIC Link is Down
e1000e 0000:00:03.0 ens3: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On relevant platforms ndo_start_xmit can handle socket buffer
fragments in high memory
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function description for igc_alloc_rx_buffers has not reflected
the function meaning. Add meaningful description.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function description for igc_is_non_eop includes an extra @skb
parameter description. This parameter doesn't exist on the function, so
remove it.
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the pci_release_mem_regions method instead of the
pci_release_selected_regions method
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Improve the probe flow and set both the DMA mask and the coherent
to the same thing. Make the flow optimized and cleared.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Scatter gather is used to do DMA data transfers of data that is written to
noncontiguous areas of memory.
This patch enables scatter gather support.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If Rx flow control has been enabled (via autoneg or forced), packets
should not be dropped due to Rx descriptor ring exhaustion. Instead
pause frames should be used to apply back pressure. This only applies
if VFs are not in use.
Move SRRCTL setup to its own function for easy reuse and only set drop
enable bit if Rx flow control is not enabled.
Since v1: always enable dropping of packets if VFs in use.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking fixes from David Miller:
1) Fix big endian overflow in nf_flow_table, from Arnd Bergmann.
2) Fix port selection on big endian in nft_tproxy, from Phil Sutter.
3) Fix precision tracking for unbound scalars in bpf verifier, from
Daniel Borkmann.
4) Fix integer overflow in socket rcvbuf check in UDP, from Antonio
Messina.
5) Do not perform a neigh confirmation during a pmtu update over a
tunnel, from Hangbin Liu.
6) Fix DMA mapping leak in dpaa_eth driver, from Madalin Bucur.
7) Various PTP fixes for sja1105 dsa driver, from Vladimir Oltean.
8) Add missing to dummy definition of of_mdiobus_child_is_phy(), from
Geert Uytterhoeven
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (54 commits)
hsr: fix slab-out-of-bounds Read in hsr_debugfs_rename()
net/sched: add delete_empty() to filters and use it in cls_flower
tcp: Fix highest_sack and highest_sack_seq
ptp: fix the race between the release of ptp_clock and cdev
net: dsa: sja1105: Reconcile the meaning of TPID and TPID2 for E/T and P/Q/R/S
Documentation: net: dsa: sja1105: Remove text about taprio base-time limitation
net: dsa: sja1105: Remove restriction of zero base-time for taprio offload
net: dsa: sja1105: Really make the PTP command read-write
net: dsa: sja1105: Take PTP egress timestamp by port, not mgmt slot
cxgb4/cxgb4vf: fix flow control display for auto negotiation
mlxsw: spectrum: Use dedicated policer for VRRP packets
mlxsw: spectrum_router: Skip loopback RIFs during MAC validation
net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs
net/sched: act_mirred: Pull mac prior redir to non mac_header_xmit device
net_sched: sch_fq: properly set sk->sk_pacing_status
bnx2x: Fix accounting of vlan resources among the PFs
bnx2x: Use appropriate define for vlan credit
of: mdio: Add missing inline to of_mdiobus_child_is_phy() dummy
net: phy: aquantia: add suspend / resume ops for AQR105
dpaa_eth: fix DMA mapping leak
...
Revert "net/sched: cls_u32: fix refcount leak in the error path of
u32_change()", and fix the u32 refcount leak in a more generic way that
preserves the semantic of rule dumping.
On tc filters that don't support lockless insertion/removal, there is no
need to guard against concurrent insertion when a removal is in progress.
Therefore, for most of them we can avoid a full walk() when deleting, and
just decrease the refcount, like it was done on older Linux kernels.
This fixes situations where walk() was wrongly detecting a non-empty
filter, like it happened with cls_u32 in the error path of change(), thus
leading to failures in the following tdc selftests:
6aa7: (filter, u32) Add/Replace u32 with source match and invalid indev
6658: (filter, u32) Add/Replace u32 with custom hash table and invalid handle
74c2: (filter, u32) Add/Replace u32 filter with invalid hash table id
On cls_flower, and on (future) lockless filters, this check is necessary:
move all the check_empty() logic in a callback so that each filter
can have its own implementation. For cls_flower, it's sufficient to check
if no IDRs have been allocated.
This reverts commit 275c44aa19.
Changes since v1:
- document the need for delete_empty() when TCF_PROTO_OPS_DOIT_UNLOCKED
is used, thanks to Vlad Buslov
- implement delete_empty() without doing fl_walk(), thanks to Vlad Buslov
- squash revert and new fix in a single patch, to be nice with bisect
tests that run tdc on u32 filter, thanks to Dave Miller
Fixes: 275c44aa19 ("net/sched: cls_u32: fix refcount leak in the error path of u32_change()")
Fixes: 6676d5e416 ("net: sched: set dedicated tcf_walker flag when tp is empty")
Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Suggested-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Tested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gma_flag was set at the time of GMA command request but it should
only be set after getting successful response. Movinng this flag
setting in GMA response handler.
This flag is used mainly for not repeating GMA command once
received MAC address.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_outq_sack is the main function handles SACK, it is called very
frequently. As the commit "move trace_sctp_probe_path into sctp_outq_sack"
added below code to this function, sctp tracepoint is disabled most of time,
but the loop of transport list will be always called even though the
tracepoint is disabled, this is unnecessary.
+ /* SCTP path tracepoint for congestion control debugging. */
+ list_for_each_entry(transport, transport_list, transports) {
+ trace_sctp_probe_path(transport, asoc);
+ }
This patch is to add tracepoint enabled check at outside of the loop of
transport list, and avoid traversing the loop when trace is disabled,
it is a small optimization.
Signed-off-by: Kevin Kou <qdkevin.kou@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Improvements to SJA1105 DSA RX timestamping
This series makes the sja1105 DSA driver use a dedicated kernel thread
for RX timestamping, a process which is time-sensitive and otherwise a
bit fragile. This allows users to customize their system (probabil an
embedded PTP switch) fully and allocate the CPU bandwidth for the driver
to expedite the RX timestamps as quickly as possible.
While doing this conversion, add a function to the PTP core for
cancelling this kernel thread (function which I found rather strange to
be missing).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When disabling PTP timestamping, don't reset the switch with the new
static config until all existing PTP frames have been timestamped on the
RX path or dropped. There's nothing we can do with these afterwards.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And move the queue of skb's waiting for RX timestamps into the ptp_data
structure, since it isn't needed if PTP is not compiled.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to effectively use the PTP kernel thread for tasks such as
timestamping packets, allow the user control over stopping it, which is
needed e.g. when the timestamping queues must be drained.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From commit 50895b9de1 ("tcp: highest_sack fix"), the logic about
setting tp->highest_sack to the head of the send queue was removed.
Of course the logic is error prone, but it is logical. Before we
remove the pointer to the highest sack skb and use the seq instead,
we need to set tp->highest_sack to NULL when there is no skb after
the last sack, and then replace NULL with the real skb when new skb
inserted into the rtx queue, because the NULL means the highest sack
seq is tp->snd_nxt. If tp->highest_sack is NULL and new data sent,
the next ACK with sack option will increase tp->reordering unexpectedly.
This patch sets tp->highest_sack to the tail of the rtx queue if
it's NULL and new data is sent. The patch keeps the rule that the
highest_sack can only be maintained by sack processing, except for
this only case.
Fixes: 50895b9de1 ("tcp: highest_sack fix")
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a case when a ptp chardev (like /dev/ptp0) is open but an underlying
device is removed, closing this file leads to a race. This reproduces
easily in a kvm virtual machine:
ts# cat openptp0.c
int main() { ... fp = fopen("/dev/ptp0", "r"); ... sleep(10); }
ts# uname -r
5.5.0-rc3-46cf053e
ts# cat /proc/cmdline
... slub_debug=FZP
ts# modprobe ptp_kvm
ts# ./openptp0 &
[1] 670
opened /dev/ptp0, sleeping 10s...
ts# rmmod ptp_kvm
ts# ls /dev/ptp*
ls: cannot access '/dev/ptp*': No such file or directory
ts# ...woken up
[ 48.010809] general protection fault: 0000 [#1] SMP
[ 48.012502] CPU: 6 PID: 658 Comm: openptp0 Not tainted 5.5.0-rc3-46cf053e #25
[ 48.014624] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), ...
[ 48.016270] RIP: 0010:module_put.part.0+0x7/0x80
[ 48.017939] RSP: 0018:ffffb3850073be00 EFLAGS: 00010202
[ 48.018339] RAX: 000000006b6b6b6b RBX: 6b6b6b6b6b6b6b6b RCX: ffff89a476c00ad0
[ 48.018936] RDX: fffff65a08d3ea08 RSI: 0000000000000247 RDI: 6b6b6b6b6b6b6b6b
[ 48.019470] ... ^^^ a slub poison
[ 48.023854] Call Trace:
[ 48.024050] __fput+0x21f/0x240
[ 48.024288] task_work_run+0x79/0x90
[ 48.024555] do_exit+0x2af/0xab0
[ 48.024799] ? vfs_write+0x16a/0x190
[ 48.025082] do_group_exit+0x35/0x90
[ 48.025387] __x64_sys_exit_group+0xf/0x10
[ 48.025737] do_syscall_64+0x3d/0x130
[ 48.026056] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 48.026479] RIP: 0033:0x7f53b12082f6
[ 48.026792] ...
[ 48.030945] Modules linked in: ptp i6300esb watchdog [last unloaded: ptp_kvm]
[ 48.045001] Fixing recursive fault but reboot is needed!
This happens in:
static void __fput(struct file *file)
{ ...
if (file->f_op->release)
file->f_op->release(inode, file); <<< cdev is kfree'd here
if (unlikely(S_ISCHR(inode->i_mode) && inode->i_cdev != NULL &&
!(mode & FMODE_PATH))) {
cdev_put(inode->i_cdev); <<< cdev fields are accessed here
Namely:
__fput()
posix_clock_release()
kref_put(&clk->kref, delete_clock) <<< the last reference
delete_clock()
delete_ptp_clock()
kfree(ptp) <<< cdev is embedded in ptp
cdev_put
module_put(p->owner) <<< *p is kfree'd, bang!
Here cdev is embedded in posix_clock which is embedded in ptp_clock.
The race happens because ptp_clock's lifetime is controlled by two
refcounts: kref and cdev.kobj in posix_clock. This is wrong.
Make ptp_clock's sysfs device a parent of cdev with cdev_device_add()
created especially for such cases. This way the parent device with its
ptp_clock is not released until all references to the cdev are released.
This adds a requirement that an initialized but not exposed struct
device should be provided to posix_clock_register() by a caller instead
of a simple dev_t.
This approach was adopted from the commit 72139dfa24 ("watchdog: Fix
the race between the release of watchdog_core_data and cdev"). See
details of the implementation in the commit 233ed09d7f ("chardev: add
helper function to register char devs with a struct device").
Link: https://lore.kernel.org/linux-fsdevel/20191125125342.6189-1-vdronov@redhat.com/T/#u
Analyzed-by: Stephen Johnston <sjohnsto@redhat.com>
Analyzed-by: Vern Lovejoy <vlovejoy@redhat.com>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For first-generation switches (SJA1105E and SJA1105T):
- TPID means C-Tag (typically 0x8100)
- TPID2 means S-Tag (typically 0x88A8)
While for the second generation switches (SJA1105P, SJA1105Q, SJA1105R,
SJA1105S) it is the other way around:
- TPID means S-Tag (typically 0x88A8)
- TPID2 means C-Tag (typically 0x8100)
In other words, E/T tags untagged traffic with TPID, and P/Q/R/S with
TPID2.
So the patch mentioned below fixed VLAN filtering for P/Q/R/S, but broke
it for E/T.
We strive for a common code path for all switches in the family, so just
lie in the static config packing functions that TPID and TPID2 are at
swapped bit offsets than they actually are, for P/Q/R/S. This will make
both switches understand TPID to be ETH_P_8021Q and TPID2 to be
ETH_P_8021AD. The meaning from the original E/T was chosen over P/Q/R/S
because E/T is actually the one with public documentation available
(UM10944.pdf).
Fixes: f9a1a7646c ("net: dsa: sja1105: Reverse TPID and TPID2")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zvika Yehudai