The CLC decline message changed with SMC-Rv2 and supports up to
4 additional diagnosis codes.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the server side of the SMC-Rv2 processing. Process incoming
CLC messages, find eligible devices and check for a valid route to the
remote peer.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send a CLC proposal message, and the remote side process this type of
message and determine the target GID. Check for a valid route to this
GID, and complete the connection establishment.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare the connection establishment with SMC-Rv2. Detect eligible
RoCE cards and indicate all supported SMC modes for the connection.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct smc_init_info grew over time, its time to save space on stack
and allocate this struct dynamically.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_stream_kill_queues() can be called on close when there are
still outstanding skbs to transmit. Those skbs may try to queue
notifications to the error queue (e.g. timestamps).
If sk_stream_kill_queues() purges the queue without taking
its lock the queue may get corrupted, and skbs leaked.
This shows up as a warning about an rmem leak:
WARNING: CPU: 24 PID: 0 at net/ipv4/af_inet.c:154 inet_sock_destruct+0x...
The leak is always a multiple of 0x300 bytes (the value is in
%rax on my builds, so RAX: 0000000000000300). 0x300 is truesize of
an empty sk_buff. Indeed if we dump the socket state at the time
of the warning the sk_error_queue is often (but not always)
corrupted. The ->next pointer points back at the list head,
but not the ->prev pointer. Indeed we can find the leaked skb
by scanning the kernel memory for something that looks like
an skb with ->sk = socket in question, and ->truesize = 0x300.
The contents of ->cb[] of the skb confirms the suspicion that
it is indeed a timestamp notification (as generated in
__skb_complete_tx_timestamp()).
Removing purging of sk_error_queue should be okay, since
inet_sock_destruct() does it again once all socket refs
are gone. Eric suggests this may cause sockets that go
thru disconnect() to maintain notifications from the
previous incarnations of the socket, but that should be
okay since the race was there anyway, and disconnect()
is not exactly dependable.
Thanks to Jonathan Lemon and Omar Sandoval for help at various
stages of tracing the issue.
Fixes: cb9eff0978 ("net: new user space API for time stamping of incoming and outgoing packets")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is only used within pm_netlink.c now.
Fixes: 067065422f ("mptcp: add the outgoing MP_PRIO support")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current default does not allowing additional subflows, mostly
as a safety restriction to avoid uncontrolled resource consumption
on busy servers.
Still the system admin and/or the application have to opt-in to
MPTCP explicitly. After that, they need to change (increase) the
default maximum number of additional subflows.
Let set that to reasonable default, and make end-users life easier.
Additionally we need to update some self-tests accordingly.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coverity complains of a possible NULL dereference in
mptcp_getsockopt_subflow_addrs():
861 } else if (sk->sk_family == AF_INET6) {
3. returned_null: inet6_sk returns NULL. [show details]
4. var_assigned: Assigning: np = NULL return value from inet6_sk.
862 const struct ipv6_pinfo *np = inet6_sk(sk);
Fix this by checking for NULL.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/231
Fixes: c11c5906bc ("mptcp: add MPTCP_SUBFLOW_ADDRS getsockopt support")
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
[mjm: Added WARN_ON_ONCE() to the unexpected case]
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bdb7cc643f ("ipv6: Count interface receive statistics on the
ingress netdev") does not work when ip6_forward() executes on the skbs
with vrf-enslaved netdev. Use IP6CB(skb)->iif to get to the right one.
Add a selftest script to verify.
Fixes: bdb7cc643f ("ipv6: Count interface receive statistics on the ingress netdev")
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211014130845.410602-1-ssuryaextr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Multiple VRFs are generally meant to be "separate" but right now md5
keys for the default VRF also affect connections inside VRFs if the IP
addresses happen to overlap.
So far the combination of TCP_MD5SIG_FLAG_IFINDEX with tcpm_ifindex == 0
was an error, accept this to mean "key only applies to default VRF".
This is what applications using VRFs for traffic separation want.
Signed-off-by: Leonard Crestez <cdleonard@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With net.ipv4.tcp_l3mdev_accept=1 it is possible for a listen socket to
accept connection from the same client address in different VRFs. It is
also possible to set different MD5 keys for these clients which differ
only in the tcpm_l3index field.
This appears to work when distinguishing between different VRFs but not
between non-VRF and VRF connections. In particular:
* tcp_md5_do_lookup_exact will match a non-vrf key against a vrf key.
This means that adding a key with l3index != 0 after a key with l3index
== 0 will cause the earlier key to be deleted. Both keys can be present
if the non-vrf key is added later.
* _tcp_md5_do_lookup can match a non-vrf key before a vrf key. This
casues failures if the passwords differ.
Fix this by making tcp_md5_do_lookup_exact perform an actual exact
comparison on l3index and by making __tcp_md5_do_lookup perfer
vrf-bound keys above other considerations like prefixlen.
Fixes: dea53bb80e ("tcp: Add l3index to tcp_md5sig_key and md5 functions")
Signed-off-by: Leonard Crestez <cdleonard@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TCA_FQ_CODEL_CE_THRESHOLD_ECT1 boolean option to select Low Latency,
Low Loss, Scalable Throughput (L4S) style marking, along with ce_threshold.
If enabled, only packets with ECT(1) can be transformed to CE
if their sojourn time is above the ce_threshold.
Note that this new option does not change rules for codel law.
In particular, if TCA_FQ_CODEL_ECN is left enabled (this is
the default when fq_codel qdisc is created), ECT(0) packets can
still get CE if codel law (as governed by limit/target) decides so.
Section 4.3.b of current draft [1] states:
b. A scheduler with per-flow queues such as FQ-CoDel or FQ-PIE can
be used for L4S. For instance within each queue of an FQ-CoDel
system, as well as a CoDel AQM, there is typically also ECN
marking at an immediate (unsmoothed) shallow threshold to support
use in data centres (see Sec.5.2.7 of [RFC8290]). This can be
modified so that the shallow threshold is solely applied to
ECT(1) packets. Then if there is a flow of non-ECN or ECT(0)
packets in the per-flow-queue, the Classic AQM (e.g. CoDel) is
applied; while if there is a flow of ECT(1) packets in the queue,
the shallower (typically sub-millisecond) threshold is applied.
Tested:
tc qd replace dev eth1 root fq_codel ce_threshold_ect1 50usec
netperf ... -t TCP_STREAM -- K dctcp
tc -s -d qd sh dev eth1
qdisc fq_codel 8022: root refcnt 32 limit 10240p flows 1024 quantum 9212 target 5ms ce_threshold_ect1 49us interval 100ms memory_limit 32Mb ecn drop_batch 64
Sent 14388596616 bytes 9543449 pkt (dropped 0, overlimits 0 requeues 152013)
backlog 0b 0p requeues 152013
maxpacket 68130 drop_overlimit 0 new_flow_count 95678 ecn_mark 0 ce_mark 7639
new_flows_len 0 old_flows_len 0
[1] L4S current draft:
https://datatracker.ietf.org/doc/html/draft-ietf-tsvwg-l4s-arch
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Ingemar Johansson S <ingemar.s.johansson@ericsson.com>
Cc: Tom Henderson <tomh@tomh.org>
Cc: Bob Briscoe <in@bobbriscoe.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of percpu_counter structure to track count of orphaned
sockets is causing problems on modern hosts with 256 cpus
or more.
Stefan Bach reported a serious spinlock contention in real workloads,
that I was able to reproduce with a netfilter rule dropping
incoming FIN packets.
53.56% server [kernel.kallsyms] [k] queued_spin_lock_slowpath
|
---queued_spin_lock_slowpath
|
--53.51%--_raw_spin_lock_irqsave
|
--53.51%--__percpu_counter_sum
tcp_check_oom
|
|--39.03%--__tcp_close
| tcp_close
| inet_release
| inet6_release
| sock_close
| __fput
| ____fput
| task_work_run
| exit_to_usermode_loop
| do_syscall_64
| entry_SYSCALL_64_after_hwframe
| __GI___libc_close
|
--14.48%--tcp_out_of_resources
tcp_write_timeout
tcp_retransmit_timer
tcp_write_timer_handler
tcp_write_timer
call_timer_fn
expire_timers
__run_timers
run_timer_softirq
__softirqentry_text_start
As explained in commit cf86a086a1 ("net/dst: use a smaller percpu_counter
batch for dst entries accounting"), default batch size is too big
for the default value of tcp_max_orphans (262144).
But even if we reduce batch sizes, there would still be cases
where the estimated count of orphans is beyond the limit,
and where tcp_too_many_orphans() has to call the expensive
percpu_counter_sum_positive().
One solution is to use plain per-cpu counters, and have
a timer to periodically refresh this cache.
Updating this cache every 100ms seems about right, tcp pressure
state is not radically changing over shorter periods.
percpu_counter was nice 15 years ago while hosts had less
than 16 cpus, not anymore by current standards.
v2: Fix the build issue for CONFIG_CRYPTO_DEV_CHELSIO_TLS=m,
reported by kernel test robot <lkp@intel.com>
Remove unused socket argument from tcp_too_many_orphans()
Fixes: dd24c00191 ("net: Use a percpu_counter for orphan_count")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Stefan Bach <sfb@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mctp_key_alloc() returns a key already referenced.
The mctp_route_input() path receives a packet for a bind socket and
allocates a key. It passes the key to mctp_key_add() which takes a
refcount and adds the key to lists. mctp_route_input() should then
release its own refcount when setting the key pointer to NULL.
In the mctp_alloc_local_tag() path (for mctp_local_output()) we
similarly need to unref the key before returning (mctp_reserve_tag()
takes a refcount and adds the key to lists).
Fixes: 73c618456d ("mctp: locking, lifetime and validity changes for sk_keys")
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the 32-bit arch with 64-bit DMA seems to rare those days,
and page pool might carry a lot of code and complexity for
systems that possibly.
So disable dma mapping support for such systems, if drivers
really want to work on such systems, they have to implement
their own DMA-mapping fallback tracking outside page_pool.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The combination of NUD_PERMANENT + NTF_MANAGED is not supported and does
not make sense either given the former indicates a static/fixed neighbor
entry whereas the latter a dynamically resolved one. While it is possible
to transition from one over to the other, we should however reject such
creation attempts.
Fixes: 7482e3841d ("net, neigh: Add NTF_MANAGED flag for managed neighbor entries")
Suggested-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of open-coding a check for invalid bits in NTF_EXT_MASK, we can just
use the NLA_POLICY_MASK() helper instead, and simplify NDA_FLAGS_EXT sanity
check this way.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, NDA_FLAGS_EXT flags allow a maximum of 24 bits to be used for
extended neighbor flags. These are eventually fed into neigh->flags by
shifting with NTF_EXT_SHIFT as per commit 2c611ad97a ("net, neigh:
Extend neigh->flags to 32 bit to allow for extensions").
If really ever needed in future, the full 32 bits from NDA_FLAGS_EXT can
be used, it would only require to move neigh->flags from u32 to u64 inside
the kernel.
Add a build-time assertion such that when extending the NTF_EXT_MASK with
new bits, we'll trigger an error once we surpass the 24th bit. This assumes
that no bit holes in new NTF_EXT_* flags will slip in from UAPI, but I
think this is reasonable to assume.
Suggested-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tools/testing/selftests/net/ioam6.sh
7b1700e009 ("selftests: net: modify IOAM tests for undef bits")
bf77b1400a ("selftests: net: Test for the IOAM encapsulation with IPv6")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Because the data pointer of net/ipv4/vs/debug_level is not updated per
netns, it must be marked as read-only in non-init netns.
Fixes: c6d2d445d8 ("IPVS: netns, final patch enabling network name space.")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In rt_mt6(), when it's a nonlinear skb, the 1st skb_header_pointer()
only copies sizeof(struct ipv6_rt_hdr) to _route that rh points to.
The access by ((const struct rt0_hdr *)rh)->reserved will overflow
the buffer. So this access should be moved below the 2nd call to
skb_header_pointer().
Besides, after the 2nd skb_header_pointer(), its return value should
also be checked, othersize, *rp may cause null-pointer-ref.
v1->v2:
- clean up some old debugging log.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Similar to earlier patches: allow ipv4 and ipv6 to use the
same handler. ipv4 and ipv6 specific actions can be done by
checking state->pf.
v2: split the pf == NFPROTO_IPV4 check (Julian Anastasov)
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
After earlier patch ip_vs_hook_in can be used directly.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
After earlier patch we can use ip_vs_out_hook directly.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ipvs has multiple one-line wrappers for hooks, compact them.
To avoid a large patch make the two most common helpers use the same
function signature as hooks.
Next patches can then remove the oneline wrappers.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is possible now that the xt_table structure is passed via *priv.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is possible now that the xt_table structure is passed via *priv.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is possible now that the xt_table structure is passed in via *priv.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is possible now that the xt_table structure is passed in via *priv.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add egress hook for AF_PACKET sockets that have the PACKET_QDISC_BYPASS
socket option set to on, which allows packets to escape without being
filtered in the egress path.
This patch only updates the AF_PACKET path, it does not update
dev_direct_xmit() so the XDP infrastructure has a chance to bypass
Netfilter.
[lukas: acquire rcu_read_lock, fix typos, rebase]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Support classifying packets with netfilter on egress to satisfy user
requirements such as:
* outbound security policies for containers (Laura)
* filtering and mangling intra-node Direct Server Return (DSR) traffic
on a load balancer (Laura)
* filtering locally generated traffic coming in through AF_PACKET,
such as local ARP traffic generated for clustering purposes or DHCP
(Laura; the AF_PACKET plumbing is contained in a follow-up commit)
* L2 filtering from ingress and egress for AVB (Audio Video Bridging)
and gPTP with nftables (Pablo)
* in the future: in-kernel NAT64/NAT46 (Pablo)
The egress hook introduced herein complements the ingress hook added by
commit e687ad60af ("netfilter: add netfilter ingress hook after
handle_ing() under unique static key"). A patch for nftables to hook up
egress rules from user space has been submitted separately, so users may
immediately take advantage of the feature.
Alternatively or in addition to netfilter, packets can be classified
with traffic control (tc). On ingress, packets are classified first by
tc, then by netfilter. On egress, the order is reversed for symmetry.
Conceptually, tc and netfilter can be thought of as layers, with
netfilter layered above tc.
Traffic control is capable of redirecting packets to another interface
(man 8 tc-mirred). E.g., an ingress packet may be redirected from the
host namespace to a container via a veth connection:
tc ingress (host) -> tc egress (veth host) -> tc ingress (veth container)
In this case, netfilter egress classifying is not performed when leaving
the host namespace! That's because the packet is still on the tc layer.
If tc redirects the packet to a physical interface in the host namespace
such that it leaves the system, the packet is never subjected to
netfilter egress classifying. That is only logical since it hasn't
passed through netfilter ingress classifying either.
Packets can alternatively be redirected at the netfilter layer using
nft fwd. Such a packet *is* subjected to netfilter egress classifying
since it has reached the netfilter layer.
Internally, the skb->nf_skip_egress flag controls whether netfilter is
invoked on egress by __dev_queue_xmit(). Because __dev_queue_xmit() may
be called recursively by tunnel drivers such as vxlan, the flag is
reverted to false after sch_handle_egress(). This ensures that
netfilter is applied both on the overlay and underlying network.
Interaction between tc and netfilter is possible by setting and querying
skb->mark.
If netfilter egress classifying is not enabled on any interface, it is
patched out of the data path by way of a static_key and doesn't make a
performance difference that is discernible from noise:
Before: 1537 1538 1538 1537 1538 1537 Mb/sec
After: 1536 1534 1539 1539 1539 1540 Mb/sec
Before + tc accept: 1418 1418 1418 1419 1419 1418 Mb/sec
After + tc accept: 1419 1424 1418 1419 1422 1420 Mb/sec
Before + tc drop: 1620 1619 1619 1619 1620 1620 Mb/sec
After + tc drop: 1616 1624 1625 1624 1622 1619 Mb/sec
When netfilter egress classifying is enabled on at least one interface,
a minimal performance penalty is incurred for every egress packet, even
if the interface it's transmitted over doesn't have any netfilter egress
rules configured. That is caused by checking dev->nf_hooks_egress
against NULL.
Measurements were performed on a Core i7-3615QM. Commands to reproduce:
ip link add dev foo type dummy
ip link set dev foo up
modprobe pktgen
echo "add_device foo" > /proc/net/pktgen/kpktgend_3
samples/pktgen/pktgen_bench_xmit_mode_queue_xmit.sh -i foo -n 400000000 -m "11:11:11:11:11:11" -d 1.1.1.1
Accept all traffic with tc:
tc qdisc add dev foo clsact
tc filter add dev foo egress bpf da bytecode '1,6 0 0 0,'
Drop all traffic with tc:
tc qdisc add dev foo clsact
tc filter add dev foo egress bpf da bytecode '1,6 0 0 2,'
Apply this patch when measuring packet drops to avoid errors in dmesg:
https://lore.kernel.org/netdev/a73dda33-57f4-95d8-ea51-ed483abd6a7a@iogearbox.net/
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Laura García Liébana <nevola@gmail.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Prepare for addition of a netfilter egress hook by generalizing the
ingress hook include file.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Prepare for addition of a netfilter egress hook by renaming
<linux/netfilter_ingress.h> to <linux/netfilter_netdev.h>.
The egress hook also necessitates a refactoring of the include file,
but that is done in a separate commit to ease reviewing.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A handful of drivers contains loops assigning the mac
addr byte by byte. Convert those to eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In icmp_build_probe(), the icmp_ext_echo_iio parsing should be done
step by step and skb_header_pointer() return value should always be
checked, this patch fixes 3 places in there:
- On case ICMP_EXT_ECHO_CTYPE_NAME, it should only copy ident.name
from skb by skb_header_pointer(), its len is ident_len. Besides,
the return value of skb_header_pointer() should always be checked.
- On case ICMP_EXT_ECHO_CTYPE_INDEX, move ident_len check ahead of
skb_header_pointer(), and also do the return value check for
skb_header_pointer().
- On case ICMP_EXT_ECHO_CTYPE_ADDR, before accessing iio->ident.addr.
ctype3_hdr.addrlen, skb_header_pointer() should be called first,
then check its return value and ident_len.
On subcases ICMP_AFI_IP and ICMP_AFI_IP6, also do check for ident.
addr.ctype3_hdr.addrlen and skb_header_pointer()'s return value.
On subcase ICMP_AFI_IP, the len for skb_header_pointer() should be
"sizeof(iio->extobj_hdr) + sizeof(iio->ident.addr.ctype3_hdr) +
sizeof(struct in_addr)" or "ident_len".
v1->v2:
- To make it more clear, call skb_header_pointer() once only for
iio->indent's parsing as Jakub Suggested.
v2->v3:
- The extobj_hdr.length check against sizeof(_iio) should be done
before calling skb_header_pointer(), as Eric noticed.
Fixes: d329ea5bd8 ("icmp: add response to RFC 8335 PROBE messages")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/31628dd76657ea62f5cf78bb55da6b35240831f1.1634205050.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sctp_make_strreset_req() makes repeated calls to sctp_addto_chunk()
which will automatically account for padding on each call. inreq and
outreq are already 4 bytes aligned, but the payload is not and doing
SCTP_PAD4(a + b) (which _sctp_make_chunk() did implicitly here) is
different from SCTP_PAD4(a) + SCTP_PAD4(b) and not enough. It led to
possible attempt to use more buffer than it was allocated and triggered
a BUG_ON.
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Fixes: cc16f00f65 ("sctp: add support for generating stream reconf ssn reset request chunk")
Reported-by: Eiichi Tsukata <eiichi.tsukata@nutanix.com>
Signed-off-by: Eiichi Tsukata <eiichi.tsukata@nutanix.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/b97c1f8b0c7ff79ac4ed206fc2c49d3612e0850c.1634156849.git.mleitner@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'skb' is allocated in digital_in_send_sdd_req(), but not free when
digital_in_send_cmd() failed, which will cause memory leak. Fix it
by freeing 'skb' if digital_in_send_cmd() return failed.
Fixes: 2c66daecc4 ("NFC Digital: Add NFC-A technology support")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'params' is allocated in digital_tg_listen_mdaa(), but not free when
digital_send_cmd() failed, which will cause memory leak. Fix it by
freeing 'params' if digital_send_cmd() return failed.
Fixes: 1c7a4c24fb ("NFC Digital: Add target NFC-DEP support")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When nfc proto id is using, nfc_proto_register() return -EBUSY error
code, but forgot to unregister proto. Fix it by adding proto_unregister()
in the error handling case.
Fixes: c7fe3b52c1 ("NFC: add NFC socket family")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211013034932.2833737-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To be symmetric with the error unwind path of dsa_switch_setup(), call
dsa_switch_unregister_notifier() after ds->ops->teardown.
The implication is that ds->ops->teardown cannot emit cross-chip
notifiers. For example, currently the dsa_tag_8021q_unregister() call
from sja1105_teardown() does not propagate to the entire tree due to
this reason. However I cannot find an actual issue caused by this,
observed using code inspection.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211012123735.2545742-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for netdev->dev_addr being constant
make all relevant arguments in LLC and SNAP constant.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for netdev->dev_addr being constant
make all relevant arguments in AX25 constant.
Modify callers as well (netrom, rose).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When setting up a bridge with stp_state 1, topology changes are not
detected and loops are not blocked. This is because the standard way of
transmitting a packet, based on VLAN IDs redirected by VCAP IS2 to the
right egress port, does not override the port STP state (in the case of
Ocelot switches, that's really the PGID_SRC masks).
To force a packet to be injected into a port that's BLOCKING, we must
send it as a control packet, which means in the case of this tagger to
send it using the manual register injection method. We already do this
for PTP frames, extend the logic to apply to any link-local MAC DA.
Fixes: 7c83a7c539 ("net: dsa: add a second tagger for Ocelot switches based on tag_8021q")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael reported that when using the "ocelot-8021q" tagging protocol,
the switch driver module must be manually loaded before the tagging
protocol can be loaded/is available.
This appears to be the same problem described here:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
where due to the fact that DSA tagging protocols make use of symbols
exported by the switch drivers, circular dependencies appear and this
breaks module autoloading.
The ocelot_8021q driver needs the ocelot_can_inject() and
ocelot_port_inject_frame() functions from the switch library. Previously
the wrong approach was taken to solve that dependency: shims were
provided for the case where the ocelot switch library was compiled out,
but that turns out to be insufficient, because the dependency when the
switch lib _is_ compiled is problematic too.
We cannot declare ocelot_can_inject() and ocelot_port_inject_frame() as
static inline functions, because these access I/O functions like
__ocelot_write_ix() which is called by ocelot_write_rix(). Making those
static inline basically means exposing the whole guts of the ocelot
switch library, not ideal...
We already have one tagging protocol driver which calls into the switch
driver during xmit but not using any exported symbol: sja1105_defer_xmit.
We can do the same thing here: create a kthread worker and one work item
per skb, and let the switch driver itself do the register accesses to
send the skb, and then consume it.
Fixes: 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained here:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
DSA tagging protocol drivers cannot depend on symbols exported by switch
drivers, because this creates a circular dependency that breaks module
autoloading.
The tag_ocelot.c file depends on the ocelot_ptp_rew_op() function
exported by the common ocelot switch lib. This function looks at
OCELOT_SKB_CB(skb) and computes how to populate the REW_OP field of the
DSA tag, for PTP timestamping (the command: one-step/two-step, and the
TX timestamp identifier).
None of that requires deep insight into the driver, it is quite
stateless, as it only depends upon the skb->cb. So let's make it a
static inline function and put it in include/linux/dsa/ocelot.h, a
file that despite its name is used by the ocelot switch driver for
populating the injection header too - since commit 40d3f295b5 ("net:
mscc: ocelot: use common tag parsing code with DSA").
With that function declared as static inline, its body is expanded
inside each call site, so the dependency is broken and the DSA tagger
can be built without the switch library, upon which the felix driver
depends.
Fixes: 39e5308b32 ("net: mscc: ocelot: support PTP Sync one-step timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It's nice to be able to test a tagging protocol with dsa_loop, but not
at the cost of losing the ability of building the tagging protocol and
switch driver as modules, because as things stand, there is a circular
dependency between the two. Tagging protocol drivers cannot depend on
switch drivers, that is a hard fact.
The reasoning behind the blamed patch was that accessing dp->priv should
first make sure that the structure behind that pointer is what we really
think it is.
Currently the "sja1105" and "sja1110" tagging protocols only operate
with the sja1105 switch driver, just like any other tagging protocol and
switch combination. The only way to mix and match them is by modifying
the code, and this applies to dsa_loop as well (by default that uses
DSA_TAG_PROTO_NONE). So while in principle there is an issue, in
practice there isn't one.
Until we extend dsa_loop to allow user space configuration, treat the
problem as a non-issue and just say that DSA ports found by tag_sja1105
are always sja1105 ports, which is in fact true. But keep the
dsa_port_is_sja1105 function so that it's easy to patch it during
testing, and rely on dead code elimination.
Fixes: 994d2cbb08 ("net: dsa: tag_sja1105: be dsa_loop-safe")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The problem is that DSA tagging protocols really must not depend on the
switch driver, because this creates a circular dependency at insmod
time, and the switch driver will effectively not load when the tagging
protocol driver is missing.
The code was structured in the way it was for a reason, though. The DSA
driver-facing API for PTP timestamping relies on the assumption that
two-step TX timestamps are provided by the hardware in an out-of-band
manner, typically by raising an interrupt and making that timestamp
available inside some sort of FIFO which is to be accessed over
SPI/MDIO/etc.
So the API puts .port_txtstamp into dsa_switch_ops, because it is
expected that the switch driver needs to save some state (like put the
skb into a queue until its TX timestamp arrives).
On SJA1110, TX timestamps are provided by the switch as Ethernet
packets, so this makes them be received and processed by the tagging
protocol driver. This in itself is great, because the timestamps are
full 64-bit and do not require reconstruction, and since Ethernet is the
fastest I/O method available to/from the switch, PTP timestamps arrive
very quickly, no matter how bottlenecked the SPI connection is, because
SPI interaction is not needed at all.
DSA's code structure and strict isolation between the tagging protocol
driver and the switch driver break the natural code organization.
When the tagging protocol driver receives a packet which is classified
as a metadata packet containing timestamps, it passes those timestamps
one by one to the switch driver, which then proceeds to compare them
based on the recorded timestamp ID that was generated in .port_txtstamp.
The communication between the tagging protocol and the switch driver is
done through a method exported by the switch driver, sja1110_process_meta_tstamp.
To satisfy build requirements, we force a dependency to build the
tagging protocol driver as a module when the switch driver is a module.
However, as explained in the first paragraph, that causes the circular
dependency.
To solve this, move the skb queue from struct sja1105_private :: struct
sja1105_ptp_data to struct sja1105_private :: struct sja1105_tagger_data.
The latter is a data structure for which hacks have already been put
into place to be able to create persistent storage per switch that is
accessible from the tagging protocol driver (see sja1105_setup_ports).
With the skb queue directly accessible from the tagging protocol driver,
we can now move sja1110_process_meta_tstamp into the tagging driver
itself, and avoid exporting a symbol.
Fixes: 566b18c8b7 ("net: dsa: sja1105: implement TX timestamping for SJA1110")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit a0c76345e3 ("devlink: disallow reload operation during device
cleanup") added devlink_reload_{enable,disable}() APIs to prevent reload
operation from racing with device probe/dismantle.
After recent changes to move devlink_register() to the end of device
probe and devlink_unregister() to the beginning of device dismantle,
these races can no longer happen. Reload operations will be denied if
the devlink instance is unregistered and devlink_unregister() will block
until all in-flight operations are done.
Therefore, remove these devlink_reload_{enable,disable}() APIs.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce new devlink call to set feature mask to control devlink
behavior during device initialization phase after devlink_alloc()
is already called.
This allows us to set reload ops based on device property which
is not known at the beginning of driver initialization.
For the sake of simplicity, this API lacks any type of locking and
needs to be called before devlink_register() to make sure that no
parallel access to the ops is possible at this stage.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Initial annotation patch to separate calls that needs to be executed
before or after devlink_register().
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Both netdev_to_devlink and netdev_to_devlink_port are used in devlink.c
only, so move them in order to reduce their scope.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The declaration of struct devlink in general header provokes the
situation where internal fields can be accidentally used by the driver
authors. In order to reduce such possible situations, let's reduce the
namespace exposure of struct devlink.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Flip the sign of a return value check, thereby suppressing the following
spurious error:
port 2 failed to notify DSA_NOTIFIER_BRIDGE_LEAVE: -EOPNOTSUPP
... which is emitted when removing an unoffloaded DSA switch port from a
bridge.
Fixes: d371b7c92d ("net: dsa: Unset vlan_filtering when ports leave the bridge")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211012112730.3429157-1-alvin@pqrs.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The check for undefined bits in the trace type is moved from the input side to
the output side, while the input side is relaxed and now inserts default empty
values when an undefined bit is set.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow a user space control plane to insert entries with a new NTF_EXT_MANAGED
flag. The flag then indicates to the kernel that the neighbor entry should be
periodically probed for keeping the entry in NUD_REACHABLE state iff possible.
The use case for this is targeting XDP or tc BPF load-balancers which use
the bpf_fib_lookup() BPF helper in order to piggyback on neighbor resolution
for their backends. Given they cannot be resolved in fast-path, a control
plane inserts the L3 (without L2) entries manually into the neighbor table
and lets the kernel do the neighbor resolution either on the gateway or on
the backend directly in case the latter resides in the same L2. This avoids
to deal with L2 in the control plane and to rebuild what the kernel already
does best anyway.
NTF_EXT_MANAGED can be combined with NTF_EXT_LEARNED in order to avoid GC
eviction. The kernel then adds NTF_MANAGED flagged entries to a per-neighbor
table which gets triggered by the system work queue to periodically call
neigh_event_send() for performing the resolution. The implementation allows
migration from/to NTF_MANAGED neighbor entries, so that already existing
entries can be converted by the control plane if needed. Potentially, we could
make the interval for periodically calling neigh_event_send() configurable;
right now it's set to DELAY_PROBE_TIME which is also in line with mlxsw which
has similar driver-internal infrastructure c723c735fa ("mlxsw: spectrum_router:
Periodically update the kernel's neigh table"). In future, the latter could
possibly reuse the NTF_MANAGED neighbors as well.
Example:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 managed extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a managed extern_learn REACHABLE
[...]
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Roopa Prabhu <roopa@nvidia.com>
Link: https://linuxplumbersconf.org/event/11/contributions/953/
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, all bits in struct ndmsg's ndm_flags are used up with the most
recent addition of 435f2e7cc0 ("net: bridge: add support for sticky fdb
entries"). This makes it impossible to extend the neighboring subsystem
with new NTF_* flags:
struct ndmsg {
__u8 ndm_family;
__u8 ndm_pad1;
__u16 ndm_pad2;
__s32 ndm_ifindex;
__u16 ndm_state;
__u8 ndm_flags;
__u8 ndm_type;
};
There are ndm_pad{1,2} attributes which are not used. However, due to
uncareful design, the kernel does not enforce them to be zero upon new
neighbor entry addition, and given they've been around forever, it is
not possible to reuse them today due to risk of breakage. One option to
overcome this limitation is to add a new NDA_FLAGS_EXT attribute for
extended flags.
In struct neighbour, there is a 3 byte hole between protocol and ha_lock,
which allows neigh->flags to be extended from 8 to 32 bits while still
being on the same cacheline as before. This also allows for all future
NTF_* flags being in neigh->flags rather than yet another flags field.
Unknown flags in NDA_FLAGS_EXT will be rejected by the kernel.
Co-developed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, it is not possible to migrate a neighbor entry between NUD_PERMANENT
state and NTF_USE flag with a dynamic NUD state from a user space control plane.
Similarly, it is not possible to add/remove NTF_EXT_LEARNED flag from an existing
neighbor entry in combination with NTF_USE flag.
This is due to the latter directly calling into neigh_event_send() without any
meta data updates as happening in __neigh_update(). Thus, to enable this use
case, extend the latter with a NEIGH_UPDATE_F_USE flag where we break the
NUD_PERMANENT state in particular so that a latter neigh_event_send() is able
to re-resolve a neighbor entry.
Before fix, NUD_PERMANENT -> NUD_* & NTF_USE:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a PERMANENT
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a PERMANENT
[...]
As can be seen, despite the admin-triggered replace, the entry remains in the
NUD_PERMANENT state.
After fix, NUD_PERMANENT -> NUD_* & NTF_USE:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a PERMANENT
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a extern_learn REACHABLE
[...]
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a extern_learn STALE
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a PERMANENT
[...]
After the fix, the admin-triggered replace switches to a dynamic state from
the NTF_USE flag which triggered a new neighbor resolution. Likewise, we can
transition back from there, if needed, into NUD_PERMANENT.
Similar before/after behavior can be observed for below transitions:
Before fix, NTF_USE -> NTF_USE | NTF_EXT_LEARNED -> NTF_USE:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a REACHABLE
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a REACHABLE
[...]
After fix, NTF_USE -> NTF_USE | NTF_EXT_LEARNED -> NTF_USE:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a REACHABLE
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a extern_learn REACHABLE
[...]
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a REACHABLE
[..]
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NTF_EXT_LEARNED neigh flag is usually propagated back to user space
upon dump of the neighbor table. However, when used in combination with
NTF_USE flag this is not the case despite exempting the entry from the
garbage collector. This results in inconsistent state since entries are
typically marked in neigh->flags with NTF_EXT_LEARNED, but here they are
not. Fix it by propagating the creation flag to ___neigh_create().
Before fix:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a REACHABLE
[...]
After fix:
# ./ip/ip n replace 192.168.178.30 dev enp5s0 use extern_learn
# ./ip/ip n
192.168.178.30 dev enp5s0 lladdr f4:8c:50:5e:71:9a extern_learn REACHABLE
[...]
Fixes: 9ce33e4653 ("neighbour: support for NTF_EXT_LEARNED flag")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Then name of this protocol changed in commit 94531cfcbe ("af_unix: Add
unix_stream_proto for sockmap") because that commit added stream support
to the af_unix protocol. Renaming the existing protocol makes a ChromeOS
protocol test[1] fail now that the name has changed in
/proc/net/protocols from "UNIX" to "UNIX-DGRAM".
Let's put the name back to how it was while keeping the stream protocol
as "UNIX-STREAM" so that the procfs interface doesn't change. This fixes
the test and maintains backwards compatibility in proc.
Cc: Jiang Wang <jiang.wang@bytedance.com>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: Cong Wang <cong.wang@bytedance.com>
Cc: Jakub Sitnicki <jakub@cloudflare.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Dmitry Osipenko <digetx@gmail.com>
Link: https://source.chromium.org/chromiumos/chromiumos/codesearch/+/main:src/platform/tast-tests/src/chromiumos/tast/local/bundles/cros/network/supported_protocols.go;l=50;drc=e8b1c3f94cb40a054f4aa1ef1aff61e75dc38f18 [1]
Fixes: 94531cfcbe ("af_unix: Add unix_stream_proto for sockmap")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace standard GPLv2 license text with SPDX tag. Although the comment
mentions GPLv2-only, it refers to the full license file which allows
later GPL versions.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ftrace is a preferred and standard way to debug entering and exiting
functions so drop useless debug prints.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cosmetic commit making dev_get_port_parent_id slightly more readable.
There is no need to split the condition to return after calling
devlink_compat_switch_id_get and after that 'recurse' is always true.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was a documented fact that ds->ops->change_tag_protocol() offered
rtnetlink mutex protection to the switch driver, since there was an
ASSERT_RTNL right before the call in dsa_switch_change_tag_proto()
(initiated from sysfs).
The blamed commit introduced another call path for
ds->ops->change_tag_protocol() which does not hold the rtnl_mutex.
This is:
dsa_tree_setup
-> dsa_tree_setup_switches
-> dsa_switch_setup
-> dsa_switch_setup_tag_protocol
-> ds->ops->change_tag_protocol()
-> dsa_port_setup
-> dsa_slave_create
-> register_netdevice(slave_dev)
-> dsa_tree_setup_master
-> dsa_master_setup
-> dev->dsa_ptr = cpu_dp
The reason why the rtnl_mutex is held in the sysfs call path is to
ensure that, once the master and all the DSA interfaces are down (which
is required so that no packets flow), they remain down during the
tagging protocol change.
The above calling order illustrates the fact that it should not be risky
to change the initial tagging protocol to the one specified in the
device tree at the given time:
- packets cannot enter the dsa_switch_rcv() packet type handler since
netdev_uses_dsa() for the master will not yet return true, since
dev->dsa_ptr has not yet been populated
- packets cannot enter the dsa_slave_xmit() function because no DSA
interface has yet been registered
So from the DSA core's perspective, holding the rtnl_mutex is indeed not
necessary.
Yet, drivers may need to do things which need rtnl_mutex protection. For
example:
felix_set_tag_protocol
-> felix_setup_tag_8021q
-> dsa_tag_8021q_register
-> dsa_tag_8021q_setup
-> dsa_tag_8021q_port_setup
-> vlan_vid_add
-> ASSERT_RTNL
These drivers do not really have a choice to take the rtnl_mutex
themselves, since in the sysfs case, the rtnl_mutex is already held.
Fixes: deff710703 ("net: dsa: Allow default tag protocol to be overridden from DT")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_addr_set() instead of writing directly to netdev->dev_addr
in various misc and old drivers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduction of lockless subqueues broke the class statistics.
Before the change stats were accumulated in `bstats' and `qstats'
on the stack which was then copied to struct gnet_dump.
After the change the `bstats' and `qstats' are initialized to 0
and never updated, yet still fed to gnet_dump. The code updates
the global qdisc->cpu_bstats and qdisc->cpu_qstats instead,
clobbering them. Most likely a copy-paste error from the code in
mqprio_dump().
__gnet_stats_copy_basic() and __gnet_stats_copy_queue() accumulate
the values for per-CPU case but for global stats they overwrite
the value, so only stats from the last loop iteration / tc end up
in sch->[bq]stats.
Use the on-stack [bq]stats variables again and add the stats manually
in the global case.
Fixes: ce679e8df7 ("net: sched: add support for TCQ_F_NOLOCK subqueues to sch_mqprio")
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
https://lore.kernel.org/all/20211007175000.2334713-2-bigeasy@linutronix.de/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similar to commit 6087175b79 ("net: dsa: mt7530: use independent VLAN
learning on VLAN-unaware bridges"), software forwarding between an
unoffloaded LAG port (a bonding interface with an unsupported policy)
and a mv88e6xxx user port directly under a bridge is broken.
We adopt the same strategy, which is to make the standalone ports not
find any ATU entry learned on a bridge port.
Theory: the mv88e6xxx ATU is looked up by FID and MAC address. There are
as many FIDs as VIDs (4096). The FID is derived from the VID when
possible (the VTU maps a VID to a FID), with a fallback to the port
based default FID value when not (802.1Q Mode is disabled on the port,
or the classified VID isn't present in the VTU).
The mv88e6xxx driver makes the following use of FIDs and VIDs:
- the port's DefaultVID (to which untagged & pvid-tagged packets get
classified) is 0 and is absent from the VTU, so this kind of packets is
processed in FID 0, the default FID assigned by mv88e6xxx_setup_port.
- every time a bridge VLAN is created, mv88e6xxx_port_vlan_join() ->
mv88e6xxx_atu_new() associates a FID with that VID which increases
linearly starting from 1. Like this:
bridge vlan add dev lan0 vid 100 # FID 1
bridge vlan add dev lan1 vid 100 # still FID 1
bridge vlan add dev lan2 vid 1024 # FID 2
The FID allocation made by the driver is sub-optimal for the following
reasons:
(a) A standalone port has a DefaultPVID of 0 and a default FID of 0 too.
A VLAN-unaware bridged port has a DefaultPVID of 0 and a default FID
of 0 too. The difference is that the bridged ports may learn ATU
entries, while the standalone port has the requirement that it must
not, and must not find them either. Standalone ports must not use
the same FID as ports belonging to a bridge. All standalone ports
can use the same FID, since the ATU will never have an entry in
that FID.
(b) Multiple VLAN-unaware bridges will all use a DefaultPVID of 0 and a
default FID of 0 on all their ports. The FDBs will not be isolated
between these bridges. Every VLAN-unaware bridge must use the same
FID on all its ports, different from the FID of other bridge ports.
(c) Each bridge VLAN uses a unique FID which is useful for Independent
VLAN Learning, but the same VLAN ID on multiple VLAN-aware bridges
will result in the same FID being used by mv88e6xxx_atu_new().
The correct behavior is for VLAN 1 in br0 to have a different FID
compared to VLAN 1 in br1.
This patch cannot fix all the above. Traditionally the DSA framework did
not care about this, and the reality is that DSA core involvement is
needed for the aforementioned issues to be solved. The only thing we can
solve here is an issue which does not require API changes, and that is
issue (a), aka use a different FID for standalone ports vs ports under
VLAN-unaware bridges.
The first step is deciding what VID and FID to use for standalone ports,
and what VID and FID for bridged ports. The 0/0 pair for standalone
ports is what they used up till now, let's keep using that. For bridged
ports, there are 2 cases:
- VLAN-aware ports will never end up using the port default FID, because
packets will always be classified to a VID in the VTU or dropped
otherwise. The FID is the one associated with the VID in the VTU.
- On VLAN-unaware ports, we _could_ leave their DefaultVID (pvid) at
zero (just as in the case of standalone ports), and just change the
port's default FID from 0 to a different number (say 1).
However, Tobias points out that there is one more requirement to cater to:
cross-chip bridging. The Marvell DSA header does not carry the FID in
it, only the VID. So once a packet crosses a DSA link, if it has a VID
of zero it will get classified to the default FID of that cascade port.
Relying on a port default FID for upstream cascade ports results in
contradictions: a default FID of 0 breaks ATU isolation of bridged ports
on the downstream switch, a default FID of 1 breaks standalone ports on
the downstream switch.
So not only must standalone ports have different FIDs compared to
bridged ports, they must also have different DefaultVID values.
IEEE 802.1Q defines two reserved VID values: 0 and 4095. So we simply
choose 4095 as the DefaultVID of ports belonging to VLAN-unaware
bridges, and VID 4095 maps to FID 1.
For the xmit operation to look up the same ATU database, we need to put
VID 4095 in DSA tags sent to ports belonging to VLAN-unaware bridges
too. All shared ports are configured to map this VID to the bridging
FID, because they are members of that VLAN in the VTU. Shared ports
don't need to have 802.1QMode enabled in any way, they always parse the
VID from the DSA header, they don't need to look at the 802.1Q header.
We install VID 4095 to the VTU in mv88e6xxx_setup_port(), with the
mention that mv88e6xxx_vtu_setup() which was located right below that
call was flushing the VTU so those entries wouldn't be preserved.
So we need to relocate the VTU flushing prior to the port initialization
during ->setup(). Also note that this is why it is safe to assume that
VID 4095 will get associated with FID 1: the user ports haven't been
created, so there is no avenue for the user to create a bridge VLAN
which could otherwise race with the creation of another FID which would
otherwise use up the non-reserved FID value of 1.
[ Currently mv88e6xxx_port_vlan_join() doesn't have the option of
specifying a preferred FID, it always calls mv88e6xxx_atu_new(). ]
mv88e6xxx_port_db_load_purge() is the function to access the ATU for
FDB/MDB entries, and it used to determine the FID to use for
VLAN-unaware FDB entries (VID=0) using mv88e6xxx_port_get_fid().
But the driver only called mv88e6xxx_port_set_fid() once, during probe,
so no surprises, the port FID was always 0, the call to get_fid() was
redundant. As much as I would have wanted to not touch that code, the
logic is broken when we add a new FID which is not the port-based
default. Now the port-based default FID only corresponds to standalone
ports, and FDB/MDB entries belong to the bridging service. So while in
the future, when the DSA API will support FDB isolation, we will have to
figure out the FID based on the bridge number, for now there's a single
bridging FID, so hardcode that.
Lastly, the tagger needs to check, when it is transmitting a VLAN
untagged skb, whether it is sending it towards a bridged or a standalone
port. When we see it is bridged we assume the bridge is VLAN-unaware.
Not because it cannot be VLAN-aware but:
- if we are transmitting from a VLAN-aware bridge we are likely doing so
using TX forwarding offload. That code path guarantees that skbs have
a vlan hwaccel tag in them, so we would not enter the "else" branch
of the "if (skb->protocol == htons(ETH_P_8021Q))" condition.
- if we are transmitting on behalf of a VLAN-aware bridge but with no TX
forwarding offload (no PVT support, out of space in the PVT, whatever),
we would indeed be transmitting with VLAN 4095 instead of the bridge
device's pvid. However we would be injecting a "From CPU" frame, and
the switch won't learn from that - it only learns from "Forward" frames.
So it is inconsequential for address learning. And VLAN 4095 is
absolutely enough for the frame to exit the switch, since we never
remove that VLAN from any port.
Fixes: 57e661aae6 ("net: dsa: mv88e6xxx: Link aggregation support")
Reported-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The present code is structured this way due to an incomplete thought
process. In Documentation/networking/switchdev.rst we document that if a
bridge is VLAN-unaware, then the presence or lack of a pvid on a bridge
port (or on the bridge itself, for that matter) should not affect the
ability to receive and transmit tagged or untagged packets.
If the bridge on behalf of which we are sending this packet is
VLAN-aware, then the TX forwarding offload API ensures that the skb will
be VLAN-tagged (if the packet was sent by user space as untagged, it
will get transmitted town to the driver as tagged with the bridge
device's pvid). But if the bridge is VLAN-unaware, it may or may not be
VLAN-tagged. In fact the logic to insert the bridge's PVID came from the
idea that we should emulate what is being done in the VLAN-aware case.
But we shouldn't.
It appears that injecting packets using a VLAN ID of 0 serves the
purpose of forwarding the packets to the egress port with no VLAN tag
added or stripped by the hardware, and no filtering being performed.
So we can simply remove the superfluous logic.
One reason why this logic is broken is that when CONFIG_BRIDGE_VLAN_FILTERING=n,
we call br_vlan_get_pvid_rcu() but that returns an error and we do error
out, dropping all packets on xmit. Not really smart. This is also an
issue when the user deletes the bridge pvid:
$ bridge vlan del dev br0 vid 1 self
As mentioned, in both cases, packets should still flow freely, and they
do just that on any net device where the bridge is not offloaded, but on
mv88e6xxx they don't.
Fixes: d82f8ab0d8 ("net: dsa: tag_dsa: offload the bridge forwarding process")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20211003155141.2241314-1-andrew@lunn.ch/
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20210928233708.1246774-1-vladimir.oltean@nxp.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The dp->bridge_num is zero-based, with -1 being the encoding for an
invalid value. But dsa_bridge_num_put used to check for an invalid value
by comparing bridge_num with 0, which is of course incorrect.
The result is that the bridge_num will never get cleared by
dsa_bridge_num_put, and further port joins to other bridges will get a
bridge_num larger than the previous one, and once all the available
bridges with TX forwarding offload supported by the hardware get
exhausted, the TX forwarding offload feature is simply disabled.
In the case of sja1105, 7 iterations of the loop below are enough to
exhaust the TX forwarding offload bits, and further bridge joins operate
without that feature.
ip link add br0 type bridge vlan_filtering 1
while :; do
ip link set sw0p2 master br0 && sleep 1
ip link set sw0p2 nomaster && sleep 1
done
This issue is enough of an indication that having the dp->bridge_num
invalid encoding be a negative number is prone to bugs, so this will be
changed to a one-based value, with the dp->bridge_num of zero being the
indication of no bridge. However, that is material for net-next.
Fixes: f5e165e72b ("net: dsa: track unique bridge numbers across all DSA switch trees")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The nci_core_conn_close_rsp_packet() function will release the conn_info
with given conn_id. However, it needs to set the rf_conn_info to NULL to
prevent other routines like nci_rf_intf_activated_ntf_packet() to trigger
the UAF.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__dev_get_by_name is currently used to either retrieve a net device
reference using its name or to check if a name is already used by a
registered net device (per ns). In the later case there is no need to
return a reference to a net device.
Introduce a new helper, netdev_name_in_use, to check if a name is
currently used by a registered net device without leaking a reference
the corresponding net device. This helper uses netdev_name_node_lookup
instead of __dev_get_by_name as we don't need the extra logic retrieving
a reference to the corresponding net device.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8f3d65c166 ("net/smc: fix wait on already cleared link")
introduced link refcounting to avoid waits on already cleared links.
This patch extents and improves the refcounting to cover all
remaining possible cases for this kind of error situation.
Fixes: 15e1b99aad ("net/smc: no WR buffer wait for terminating link group")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reuse the timeval compat code from core/sock to handle 32-bit and
64-bit timeval structures. Also introduce a new socket option define
to allow using y2038 safe timeval under 32-bit.
The existing behavior of sock_set_timeout and vsock's timeout setter
differ when the time value is out of bounds. vsocks current behavior
is retained at the expense of not being able to share the full
implementation.
This allows the LTP test vsock01 to pass under 32-bit compat mode.
Fixes: fe0c72f3db ("socket: move compat timeout handling into sock.c")
Signed-off-by: Richard Palethorpe <rpalethorpe@suse.com>
Cc: Richard Palethorpe <rpalethorpe@richiejp.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for sharing the implementation of sock_get_timeout.
Signed-off-by: Richard Palethorpe <rpalethorpe@suse.com>
Cc: Richard Palethorpe <rpalethorpe@richiejp.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to deadlocks in the networking subsystem spotted 12 years ago[1],
a workaround was put in place[2] to avoid taking the rtnl lock when it
was not available and restarting the syscall (back to VFS, letting
userspace spin). The following construction is found a lot in the net
sysfs and sysctl code:
if (!rtnl_trylock())
return restart_syscall();
This can be problematic when multiple userspace threads use such
interfaces in a short period, making them to spin a lot. This happens
for example when adding and moving virtual interfaces: userspace
programs listening on events, such as systemd-udevd and NetworkManager,
do trigger actions reading files in sysfs. It gets worse when a lot of
virtual interfaces are created concurrently, say when creating
containers at boot time.
Returning early without hitting the above pattern when the syscall will
fail eventually does make things better. While it is not a fix for the
issue, it does ease things.
[1] https://lore.kernel.org/netdev/49A4D5D5.5090602@trash.net/https://lore.kernel.org/netdev/m14oyhis31.fsf@fess.ebiederm.org/
and https://lore.kernel.org/netdev/20090226084924.16cb3e08@nehalam/
[2] Rightfully, those deadlocks are *hard* to solve.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
leaf classes of ETS qdiscs are served in strict priority or deficit round
robin (DRR), depending on the value of 'nstrict'. Since this value can be
changed while traffic is running, we need to be sure that the active list
of DRR classes can be updated at any time, so:
1) call INIT_LIST_HEAD(&alist) on all leaf classes in .init(), before the
first packet hits any of them.
2) ensure that 'alist' is not overwritten with zeros when a leaf class is
no more strict priority nor DRR (i.e. array elements beyond 'nbands').
Link: https://lore.kernel.org/netdev/YS%2FoZ+f0Nr8eQkzH@dcaratti.users.ipa.redhat.com
Suggested-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
There is a handful of drivers which pass netdev->dev_addr as
the destination buffer to eth_platform_get_mac_address().
Add a helper which takes a dev pointer instead, so it can call
an appropriate helper.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
nvmem_get_mac_address() is only called from of_net.c
we don't need the export.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Relax this condition to make add and update commands idempotent for sets
with no timeout. The eval function already checks if the set element
timeout is available and updates it if the update command is used.
Fixes: 22fe54d5fe ("netfilter: nf_tables: add support for dynamic set updates")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
estimation_timer will iterate the est_list to do estimation
for each ipvs stats. When there are lots of services, the
list can be very large.
We found that estimation_timer() run for more then 200ms on a
machine with 104 CPU and 50K services.
yunhong-cgl jiang report the same phenomenon before:
https://www.spinics.net/lists/lvs-devel/msg05426.html
In some cases(for example a large K8S cluster with many ipvs services),
ipvs estimation may not be needed. So adding a sysctl blob to allow
users to disable this completely.
Default is: 1 (enable)
Cc: yunhong-cgl jiang <xintian1976@gmail.com>
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
syzbot reported following (harmless) WARN:
WARNING: CPU: 1 PID: 2648 at net/netfilter/core.c:468
nft_netdev_unregister_hooks net/netfilter/nf_tables_api.c:230 [inline]
nf_tables_unregister_hook include/net/netfilter/nf_tables.h:1090 [inline]
__nft_release_basechain+0x138/0x640 net/netfilter/nf_tables_api.c:9524
nft_netdev_event net/netfilter/nft_chain_filter.c:351 [inline]
nf_tables_netdev_event+0x521/0x8a0 net/netfilter/nft_chain_filter.c:382
reproducer:
unshare -n bash -c 'ip link add br0 type bridge; nft add table netdev t ; \
nft add chain netdev t ingress \{ type filter hook ingress device "br0" \
priority 0\; policy drop\; \}'
Problem is that when netns device exit hooks create the UNREGISTER
event, the .pre_exit hook for nf_tables core has already removed the
base hook. Notifier attempts to do this again.
The need to do base hook unregister unconditionally was needed in the past,
because notifier was last stage where reg->dev dereference was safe.
Now that nf_tables does the hook removal in .pre_exit, this isn't
needed anymore.
Reported-and-tested-by: syzbot+154bd5be532a63aa778b@syzkaller.appspotmail.com
Fixes: 767d1216bf ("netfilter: nftables: fix possible UAF over chains from packet path in netns")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This option, NF_CONNTRACK_SECMARK, is a bool, so it can never be 'm'.
Fixes: 33b8e77605 ("[NETFILTER]: Add CONFIG_NETFILTER_ADVANCED option")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The commit 6da5b0f027 ("net: ensure unbound datagram socket to be
chosen when not in a VRF") modified compute_score() so that a device
match is always made, not just in the case of an l3mdev skb, then
increments the score also for unbound sockets. This ensures that
sockets bound to an l3mdev are never selected when not in a VRF.
But as unbound and bound sockets are now scored equally, this results
in the last opened socket being selected if there are matches in the
default VRF for an unbound socket and a socket bound to a dev that is
not an l3mdev. However, handling prior to this commit was to always
select the bound socket in this case. Reinstate this handling by
incrementing the score only for bound sockets. The required isolation
due to choosing between an unbound socket and a socket bound to an
l3mdev remains in place due to the device match always being made.
The same approach is taken for compute_score() for stream sockets.
Fixes: 6da5b0f027 ("net: ensure unbound datagram socket to be chosen when not in a VRF")
Fixes: e78190581a ("net: ensure unbound stream socket to be chosen when not in a VRF")
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/cf0a8523-b362-1edf-ee78-eef63cbbb428@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf 2021-10-07
We've added 7 non-merge commits during the last 8 day(s) which contain
a total of 8 files changed, 38 insertions(+), 21 deletions(-).
The main changes are:
1) Fix ARM BPF JIT to preserve caller-saved regs for DIV/MOD JIT-internal
helper call, from Johan Almbladh.
2) Fix integer overflow in BPF stack map element size calculation when
used with preallocation, from Tatsuhiko Yasumatsu.
3) Fix an AF_UNIX regression due to added BPF sockmap support related
to shutdown handling, from Jiang Wang.
4) Fix a segfault in libbpf when generating light skeletons from objects
without BTF, from Kumar Kartikeya Dwivedi.
5) Fix a libbpf memory leak in strset to free the actual struct strset
itself, from Andrii Nakryiko.
6) Dual-license bpf_insn.h similarly as we did for libbpf and bpftool,
with ACKs from all contributors, from Luca Boccassi.
====================
Link: https://lore.kernel.org/r/20211007135010.21143-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
There is a handful of drivers which pass netdev->dev_addr as
the destination buffer to device_get_mac_address(). Add a helper
which takes a dev pointer instead, so it can call an appropriate
helper.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers pass in ETH_ALEN and the function itself
will return -EINVAL for any other address length.
Just assume it's ETH_ALEN like all other mac address
helpers (nvm, of, platform).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fwnode_get_mac_address() and device_get_mac_address()
return a pointer to the buffer that was passed to them
on success or NULL on failure. None of the callers
care about the actual value, only if it's NULL or not.
These semantics differ from of_get_mac_address() which
returns an int so to avoid confusion make the device
helpers return an errno.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the mac address helpers out, eth.c already contains
a bunch of similar helpers.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
There are roughly 40 places where netdev->dev_addr is passed
as the destination to a of_get_mac_address() call. Add a helper
which takes a dev pointer instead, so it can call an appropriate
helper.
Note that of_get_mac_address() already assumes the address is
6 bytes long (ETH_ALEN) so use eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rob suggests to move of_net.c from under drivers/of/ somewhere
to the networking code.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2021-10-07
1) Fix a sysbot reported shift-out-of-bounds in xfrm_get_default.
From Pavel Skripkin.
2) Fix XFRM_MSG_MAPPING ABI breakage. The new XFRM_MSG_MAPPING
messages were accidentally not paced at the end.
Fix by Eugene Syromiatnikov.
3) Fix the uapi for the default policy, use explicit field and macros
and make it accessible to userland.
From Nicolas Dichtel.
4) Fix a missing rcu lock in xfrm_notify_userpolicy().
From Nicolas Dichtel.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a pair of new ethtool messages, 'ETHTOOL_MSG_MODULE_SET' and
'ETHTOOL_MSG_MODULE_GET', that can be used to control transceiver
modules parameters and retrieve their status.
The first parameter to control is the power mode of the module. It is
only relevant for paged memory modules, as flat memory modules always
operate in low power mode.
When a paged memory module is in low power mode, its power consumption
is reduced to the minimum, the management interface towards the host is
available and the data path is deactivated.
User space can choose to put modules that are not currently in use in
low power mode and transition them to high power mode before putting the
associated ports administratively up. This is useful for user space that
favors reduced power consumption and lower temperatures over reduced
link up times. In QSFP-DD modules the transition from low power mode to
high power mode can take a few seconds and this transition is only
expected to get longer with future / more complex modules.
User space can control the power mode of the module via the power mode
policy attribute ('ETHTOOL_A_MODULE_POWER_MODE_POLICY'). Possible
values:
* high: Module is always in high power mode.
* auto: Module is transitioned by the host to high power mode when the
first port using it is put administratively up and to low power mode
when the last port using it is put administratively down.
The operational power mode of the module is available to user space via
the 'ETHTOOL_A_MODULE_POWER_MODE' attribute. The attribute is not
reported to user space when a module is not plugged-in.
The user API is designed to be generic enough so that it could be used
for modules with different memory maps (e.g., SFF-8636, CMIS).
The only implementation of the device driver API in this series is for a
MAC driver (mlxsw) where the module is controlled by the device's
firmware, but it is designed to be generic enough so that it could also
be used by implementations where the module is controlled by the CPU.
CMIS testing
============
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x03 (ModuleReady)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : Off
The module is not in low power mode, as it is not forced by hardware
(LowPwrAllowRequestHW is off) or by software (LowPwrRequestSW is off).
The power mode can be queried from the kernel. In case
LowPwrAllowRequestHW was on, the kernel would need to take into account
the state of the LowPwrRequestHW signal, which is not visible to user
space.
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy high
power-mode high
Change the power mode policy to 'auto':
# ethtool --set-module swp11 power-mode-policy auto
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x01 (ModuleLowPwr)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : On
Put the associated port administratively up which will instruct the host
to transition the module to high power mode:
# ip link set dev swp11 up
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode high
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x03 (ModuleReady)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : Off
Put the associated port administratively down which will instruct the
host to transition the module to low power mode:
# ip link set dev swp11 down
Query the power mode again:
$ ethtool --show-module swp11
Module parameters for swp11:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp11
Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628))
...
Module State : 0x01 (ModuleLowPwr)
LowPwrAllowRequestHW : Off
LowPwrRequestSW : On
SFF-8636 testing
================
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled
Power set : Off
Power override : On
...
Transmit avg optical power (Channel 1) : 0.7733 mW / -1.12 dBm
Transmit avg optical power (Channel 2) : 0.7649 mW / -1.16 dBm
Transmit avg optical power (Channel 3) : 0.7790 mW / -1.08 dBm
Transmit avg optical power (Channel 4) : 0.7837 mW / -1.06 dBm
Rcvr signal avg optical power(Channel 1) : 0.9302 mW / -0.31 dBm
Rcvr signal avg optical power(Channel 2) : 0.9079 mW / -0.42 dBm
Rcvr signal avg optical power(Channel 3) : 0.8993 mW / -0.46 dBm
Rcvr signal avg optical power(Channel 4) : 0.8778 mW / -0.57 dBm
The module is not in low power mode, as it is not forced by hardware
(Power override is on) or by software (Power set is off).
The power mode can be queried from the kernel. In case Power override
was off, the kernel would need to take into account the state of the
LPMode signal, which is not visible to user space.
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy high
power-mode high
Change the power mode policy to 'auto':
# ethtool --set-module swp13 power-mode-policy auto
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled
Power set : On
Power override : On
...
Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm
Put the associated port administratively up which will instruct the host
to transition the module to high power mode:
# ip link set dev swp13 up
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode high
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled
Power set : Off
Power override : On
...
Transmit avg optical power (Channel 1) : 0.7934 mW / -1.01 dBm
Transmit avg optical power (Channel 2) : 0.7859 mW / -1.05 dBm
Transmit avg optical power (Channel 3) : 0.7885 mW / -1.03 dBm
Transmit avg optical power (Channel 4) : 0.7985 mW / -0.98 dBm
Rcvr signal avg optical power(Channel 1) : 0.9325 mW / -0.30 dBm
Rcvr signal avg optical power(Channel 2) : 0.9034 mW / -0.44 dBm
Rcvr signal avg optical power(Channel 3) : 0.9086 mW / -0.42 dBm
Rcvr signal avg optical power(Channel 4) : 0.8885 mW / -0.51 dBm
Put the associated port administratively down which will instruct the
host to transition the module to low power mode:
# ip link set dev swp13 down
Query the power mode again:
$ ethtool --show-module swp13
Module parameters for swp13:
power-mode-policy auto
power-mode low
Verify with the data read from the EEPROM:
# ethtool -m swp13
Identifier : 0x11 (QSFP28)
...
Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled
Power set : On
Power override : On
...
Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm
Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm
Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
rtnl_fill_statsinfo() is filling skb with one mandatory if_stats_msg structure.
nlmsg_put(skb, pid, seq, type, sizeof(struct if_stats_msg), flags);
But if_nlmsg_stats_size() never considered the needed storage.
This bug did not show up because alloc_skb(X) allocates skb with
extra tailroom, because of added alignments. This could very well
be changed in the future to have deterministic behavior.
Fixes: 10c9ead9f3 ("rtnetlink: add new RTM_GETSTATS message to dump link stats")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Roopa Prabhu <roopa@nvidia.com>
Acked-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 94531cfcbe ("af_unix: Add unix_stream_proto for sockmap") sets
unix domain socket peer state to TCP_CLOSE in unix_shutdown. This could
happen when the local end is shutdown but the other end is not. Then,
the other end will get read or write failures which is not expected.
Fix the issue by setting the local state to shutdown.
Fixes: 94531cfcbe ("af_unix: Add unix_stream_proto for sockmap")
Reported-by: Casey Schaufler <casey@schaufler-ca.com>
Suggested-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Jiang Wang <jiang.wang@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Casey Schaufler <casey@schaufler-ca.com>
Reviewed-by: Casey Schaufler <casey@schaufler-ca.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20211004232530.2377085-1-jiang.wang@bytedance.com
- Add support for MediaTek MT7922 and MT7921
- Enable support for AOSP extention in Qualcomm WCN399x and Realtek
8822C/8852A.
- Add initial support for link quality and audio/codec offload.
- Rework of sockets sendmsg to avoid locking issues.
- Add vhci suspend/resume emulation.
-----BEGIN PGP SIGNATURE-----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=QRkQ
-----END PGP SIGNATURE-----
Merge tag 'for-net-next-2021-10-01' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Add support for MediaTek MT7922 and MT7921
- Enable support for AOSP extention in Qualcomm WCN399x and Realtek
8822C/8852A.
- Add initial support for link quality and audio/codec offload.
- Rework of sockets sendmsg to avoid locking issues.
- Add vhci suspend/resume emulation.
====================
Link: https://lore.kernel.org/r/20211001230850.3635543-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While existing code is correct, KCSAN is reporting
a data-race in netlink_insert / netlink_sendmsg [1]
It is correct to read nlk->bound without a lock, as netlink_autobind()
will acquire all needed locks.
[1]
BUG: KCSAN: data-race in netlink_insert / netlink_sendmsg
write to 0xffff8881031c8b30 of 1 bytes by task 18752 on cpu 0:
netlink_insert+0x5cc/0x7f0 net/netlink/af_netlink.c:597
netlink_autobind+0xa9/0x150 net/netlink/af_netlink.c:842
netlink_sendmsg+0x479/0x7c0 net/netlink/af_netlink.c:1892
sock_sendmsg_nosec net/socket.c:703 [inline]
sock_sendmsg net/socket.c:723 [inline]
____sys_sendmsg+0x360/0x4d0 net/socket.c:2392
___sys_sendmsg net/socket.c:2446 [inline]
__sys_sendmsg+0x1ed/0x270 net/socket.c:2475
__do_sys_sendmsg net/socket.c:2484 [inline]
__se_sys_sendmsg net/socket.c:2482 [inline]
__x64_sys_sendmsg+0x42/0x50 net/socket.c:2482
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff8881031c8b30 of 1 bytes by task 18751 on cpu 1:
netlink_sendmsg+0x270/0x7c0 net/netlink/af_netlink.c:1891
sock_sendmsg_nosec net/socket.c:703 [inline]
sock_sendmsg net/socket.c:723 [inline]
__sys_sendto+0x2a8/0x370 net/socket.c:2019
__do_sys_sendto net/socket.c:2031 [inline]
__se_sys_sendto net/socket.c:2027 [inline]
__x64_sys_sendto+0x74/0x90 net/socket.c:2027
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x00 -> 0x01
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 18751 Comm: syz-executor.0 Not tainted 5.14.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: da314c9923 ("netlink: Replace rhash_portid with bound")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No users in tree since commit a3498436b3 ("netns: restrict uevents"),
so remove this functionality.
Cc: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit de1799667b ("net: bridge: add STP xstats")
added an additional nla_reserve_64bit() in br_fill_linkxstats(),
but forgot to update br_get_linkxstats_size() accordingly.
This can trigger the following in rtnl_stats_get()
WARN_ON(err == -EMSGSIZE);
Fixes: de1799667b ("net: bridge: add STP xstats")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge_fill_linkxstats() is using nla_reserve_64bit().
We must use nla_total_size_64bit() instead of nla_total_size()
for corresponding data structure.
Fixes: 1080ab95e3 ("net: bridge: add support for IGMP/MLD stats and export them via netlink")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nikolay Aleksandrov <nikolay@nvidia.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A packet received on a trunk will have bit 2 set in Forward DSA tagged
frame. Bit 1 can be either 0 or 1 and is otherwise undefined and bit 0
indicates the frame CFI. Masking with 7 thus results in frames as
being identified as being from a trunk when in fact they are not. Fix
the mask to just look at bit 2.
Fixes: 5b60dadb71 ("net: dsa: tag_dsa: Support reception of packets from LAG devices")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sdata->tun_src should be freed before sdata is freed
because sdata->tun_src is allocated after sdata allocation.
So, kfree(sdata) and kfree(rcu_dereference_raw(sdata->tun_src)) are
changed code order.
Fixes: f04ed7d277 ("net: ipv6: check return value of rhashtable_init")
Signed-off-by: MichelleJin <shjy180909@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the ip6ip6 encapsulation by providing three encap
modes: inline, encap and auto.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This prerequisite patch provides some minor edits (alignments, renames) and a
minor modification inside a function to facilitate the next patch by using
existing nla_* functions.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch anticipates the support for the IOAM insertion inside in-transit
packets, by making a difference between input and output in order to determine
the right value for its hop-limit (inherited from the IPv6 hop-limit).
Input case: happens before ip6_forward, the IPv6 hop-limit is not decremented
yet -> decrement the IOAM hop-limit to reflect the new hop inside the trace.
Output case: happens after ip6_forward, the IPv6 hop-limit has already been
decremented -> keep the same value for the IOAM hop-limit.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add multi-packet route input tests, for message reassembly. These will
feed packets to be received by a bound socket, or dropped.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a few tests for single-packet route inputs, testing the
mctp_route_input function.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a few tests for the initial packet ingress through
mctp_pkttype_receive function; mainly packet header sanity checks. Full
input routing checks will be added as a separate change.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds the first kunit test for the mctp subsystem, and an
initial test for the fragmentation path.
We're adding tests under a new net/mctp/test/ directory.
Incorporates a fix for module configs:
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert from ether_addr_copy() to eth_hw_addr_set():
@@
expression dev, np;
@@
- ether_addr_copy(dev->dev_addr, np)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all Ethernet drivers from memcpy(... ETH_ADDR)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert sw drivers from memcpy(... ETH_ADDR) to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, all packets injected into Ocelot switches are classified to
VLAN 0, regardless of whether they are VLAN-tagged or not. This is
because the switch only looks at the VLAN TCI from the DSA tag.
VLAN 0 is then stripped on egress due to REW_TAG_CFG_TAG_CFG. There are
2 cases really, below is the explanation for ocelot_port_set_native_vlan:
- Port is VLAN-aware, we set REW_TAG_CFG_TAG_CFG to 1 (egress-tag all
frames except VID 0 and the native VLAN) if a native VLAN exists, or
to 3 otherwise (tag all frames, including VID 0).
- Port is VLAN-unaware, we set REW_TAG_CFG_TAG_CFG to 0 (port tagging
disabled, classified VLAN never appears in the packet).
One can already see an inconsistency: when a native VLAN exists, VID 0
is egress-untagged, but when it doesn't, VID 0 is egress-tagged.
So when we do this:
ip link add br0 type bridge vlan_filtering 1
ip link set swp0 master br0
bridge vlan del dev swp0 vid 1
bridge vlan add dev swp0 vid 1 pvid # but not untagged
and we ping through swp0, packets will look like this:
MAC > 33:33:00:00:00:02, ethertype 802.1Q (0x8100): vlan 0, p 0,
ethertype 802.1Q (0x8100), vlan 1, p 0, ethertype IPv6 (0x86dd),
ICMP6, router solicitation, length 16
So VID 1 frames (sent that way by the Linux bridge) are encapsulated in
a VID 0 header - the classified VLAN of the packets as far as the hw is
concerned. To avoid that, what we really need to do is stop injecting
packets using the classified VLAN of 0.
This patch strips the VLAN header from the skb payload, if that VLAN
exists and if the port is under a VLAN-aware bridge. Then it copies that
VLAN header into the DSA injection frame header.
A positive side effect is that VCAP ES0 VLAN rewriting rules now work
for packets injected from the CPU into a port that's under a VLAN-aware
bridge, and we are able to match those packets by the VLAN ID that was
sent by the network stack, and not by VLAN ID 0.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_gro_complete always returned the same value, NET_RX_SUCCESS
And the value was not used anywhere
Signed-off-by: Gyumin Hwang <hkm73560@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net (v2)
The following patchset contains Netfilter fixes for net:
1) Move back the defrag users fields to the global netns_nf area.
Kernel fails to boot if conntrack is builtin and kernel is booted
with: nf_conntrack.enable_hooks=1. From Florian Westphal.
2) Rule event notification is missing relevant context such as
the position handle and the NLM_F_APPEND flag.
3) Rule replacement is expanded to add + delete using the existing
rule handle, reverse order of this operation so it makes sense
from rule notification standpoint.
4) Propagate to userspace the NLM_F_CREATE and NLM_F_EXCL flags
from the rule notification path.
Patches #2, #3 and #4 are used by 'nft monitor' and 'iptables-monitor'
userspace utilities which are not correctly representing the following
operations through netlink notifications:
- rule insertions
- rule addition/insertion from position handle
- create table/chain/set/map/flowtable/...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Include the NLM_F_CREATE and NLM_F_EXCL flags in netlink event
notifications, otherwise userspace cannot distiguish between create and
add commands.
Fixes: 96518518cc ("netfilter: add nftables")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Daniel Borkmann says:
====================
bpf-next 2021-10-02
We've added 85 non-merge commits during the last 15 day(s) which contain
a total of 132 files changed, 13779 insertions(+), 6724 deletions(-).
The main changes are:
1) Massive update on test_bpf.ko coverage for JITs as preparatory work for
an upcoming MIPS eBPF JIT, from Johan Almbladh.
2) Add a batched interface for RX buffer allocation in AF_XDP buffer pool,
with driver support for i40e and ice from Magnus Karlsson.
3) Add legacy uprobe support to libbpf to complement recently merged legacy
kprobe support, from Andrii Nakryiko.
4) Add bpf_trace_vprintk() as variadic printk helper, from Dave Marchevsky.
5) Support saving the register state in verifier when spilling <8byte bounded
scalar to the stack, from Martin Lau.
6) Add libbpf opt-in for stricter BPF program section name handling as part
of libbpf 1.0 effort, from Andrii Nakryiko.
7) Add a document to help clarifying BPF licensing, from Alexei Starovoitov.
8) Fix skel_internal.h to propagate errno if the loader indicates an internal
error, from Kumar Kartikeya Dwivedi.
9) Fix build warnings with -Wcast-function-type so that the option can later
be enabled by default for the kernel, from Kees Cook.
10) Fix libbpf to ignore STT_SECTION symbols in legacy map definitions as it
otherwise errors out when encountering them, from Toke Høiland-Jørgensen.
11) Teach libbpf to recognize specialized maps (such as for perf RB) and
internally remove BTF type IDs when creating them, from Hengqi Chen.
12) Various fixes and improvements to BPF selftests.
====================
Link: https://lore.kernel.org/r/20211002001327.15169-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
prevent_wake logic is backward since what it is really checking is
if the device may wakeup the system or not, not that it will prevent
the to be awaken.
Also looking on how other subsystems have the entry as power/wakeup
this also renames the force_prevent_wake to force_wakeup in vhci driver.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
napi_busy_loop() disables preemption and performs a NAPI poll. We can't acquire
sleeping locks with disabled preemption which would be required while
__napi_poll() invokes the callback of the driver.
A threaded interrupt performing the NAPI-poll can be preempted on PREEMPT_RT.
A RT thread on another CPU may observe NAPIF_STATE_SCHED bit set and busy-spin
until it is cleared or its spin time runs out. Given it is the task with the
highest priority it will never observe the NEED_RESCHED bit set.
In this case the time is better spent by simply sleeping.
The NET_RX_BUSY_POLL is disabled by default (the system wide sysctls for
poll/read are set to zero). Disabling NET_RX_BUSY_POLL on PREEMPT_RT to avoid
wrong locking context in case it is used.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20211001145841.2308454-1-bigeasy@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If sd_max is unsigned, then sd_max - GSS_SEQ_WIN is a very large number
whenever sd_max is less than GSS_SEQ_WIN, and the comparison:
seq_num <= sd->sd_max - GSS_SEQ_WIN
in gss_check_seq_num is pretty much always true, even when that's
clearly not what was intended.
This was causing pynfs to hang when using krb5, because pynfs uses zero
as the initial gss sequence number. That's perfectly legal, but this
logic error causes knfsd to drop the rpc in that case. Out-of-order
sequence IDs in the first GSS_SEQ_WIN (128) calls will also cause this.
Fixes: 10b9d99a3d ("SUNRPC: Augment server-side rpcgss tracepoints")
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
This reverts commit 4f42ad2011, reversing
changes made to ea2dd331bf.
These chanfges break the build when mctp is modular.
Signed-off-by: David S. Miller <davem@davemloft.net>
Each region has an independently configurable number of maximum
snapshots. This information is not reported to userspace, making it not
very discoverable. Fix this by adding a new
DEVLINK_ATTR_REGION_MAX_SNAPSHOST attribute which is used to report this
maximum.
Ex:
$devlink region
pci/0000:af:00.0/nvm-flash: size 10485760 snapshot [] max 1
pci/0000:af:00.0/device-caps: size 4096 snapshot [] max 10
pci/0000:af:00.1/nvm-flash: size 10485760 snapshot [] max 1
pci/0000:af:00.1/device-caps: size 4096 snapshot [] max 10
This information enables users to understand why a new region command
may fail due to having too many existing snapshots.
Reported-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add multi-packet route input tests, for message reassembly. These will
feed packets to be received by a bound socket, or dropped.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a few tests for single-packet route inputs, testing the
mctp_route_input function.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a few tests for the initial packet ingress through
mctp_pkttype_receive function; mainly packet header sanity checks. Full
input routing checks will be added as a separate change.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds the first kunit test for the mctp subsystem, and an
initial test for the fragmentation path.
We're adding tests under a new net/mctp/test/ directory.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes use of bt_skb_sendmsg instead of allocating a different
buffer to be used with memcpy_from_msg which cause one extra copy.
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows
that, in the worst scenario, could lead to heap overflows.
Link: https://github.com/KSPP/linux/issues/160
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20210929201718.GA342296@embeddedor
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jann Horn reported that SO_PEERCRED and SO_PEERGROUPS implementations
are racy, as af_unix can concurrently change sk_peer_pid and sk_peer_cred.
In order to fix this issue, this patch adds a new spinlock that needs
to be used whenever these fields are read or written.
Jann also pointed out that l2cap_sock_get_peer_pid_cb() is currently
reading sk->sk_peer_pid which makes no sense, as this field
is only possibly set by AF_UNIX sockets.
We will have to clean this in a separate patch.
This could be done by reverting b48596d1dc "Bluetooth: L2CAP: Add get_peer_pid callback"
or implementing what was truly expected.
Fixes: 109f6e39fa ("af_unix: Allow SO_PEERCRED to work across namespaces.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jann Horn <jannh@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using snmp_get_cpu_field_batch() allows for better cpu cache
utilization, especially on hosts with large number of cpus.
Also remove special handling when mptcp mibs where not yet
allocated.
I chose to use temporary storage on the stack to keep this patch simple.
We might in the future use the storage allocated in netstat_seq_show().
Combined with prior patch (inlining snmp_get_cpu_field)
time to fetch and output mptcp counters on a 256 cpu host [1]
goes from 75 usec to 16 usec.
[1] L1 cache size is 32KB, it is not big enough to hold all dataset.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This trivial function is called ~90,000 times on 256 cpus hosts,
when reading /proc/net/netstat. And this number keeps inflating.
Inlining it saves many cycles.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user sets SO_RESERVE_MEM socket option, in order to utilize the
reserved memory when in memory pressure state, we adjust rcv_ssthresh
according to the available reserved memory for the socket, instead of
using 4 * advmss always.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If user sets SO_RESERVE_MEM socket option, in order to fully utilize the
reserved memory in memory pressure state on the tx path, we modify the
logic in sk_stream_moderate_sndbuf() to set sk_sndbuf according to
available reserved memory, instead of MIN_SOCK_SNDBUF, and adjust it
when new data is acked.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This socket option provides a mechanism for users to reserve a certain
amount of memory for the socket to use. When this option is set, kernel
charges the user specified amount of memory to memcg, as well as
sk_forward_alloc. This amount of memory is not reclaimable and is
available in sk_forward_alloc for this socket.
With this socket option set, the networking stack spends less cycles
doing forward alloc and reclaim, which should lead to better system
performance, with the cost of an amount of pre-allocated and
unreclaimable memory, even under memory pressure.
Note:
This socket option is only available when memory cgroup is enabled and we
require this reserved memory to be charged to the user's memcg. We hope
this could avoid mis-behaving users to abused this feature to reserve a
large amount on certain sockets and cause unfairness for others.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct dev_addr_list is used for device addresses, unicast addresses
and multicast addresses. The first of those needs special handling
of the main address - netdev->dev_addr points directly the data
of the entry and drivers write to it freely, so we can't maintain
it in the rbtree (for now, at least, to be fixed in net-next).
Current work around sprinkles special handling of the first
address on the list throughout the code but it missed the case
where address is being added. First address will not be visible
during subsequent adds.
Syzbot found a warning where unicast addresses are modified
without holding the rtnl lock, tl;dr is that team generates
the same modification multiple times, not necessarily when
right locks are held.
In the repro we have:
macvlan -> team -> veth
macvlan adds a unicast address to the team. Team then pushes
that address down to its memebers (veths). Next something unrelated
makes team sync member addrs again, and because of the bug
the addr entries get duplicated in the veths. macvlan gets
removed, removes its addr from team which removes only one
of the duplicated addresses from veths. This removal is done
under rtnl. Next syzbot uses iptables to add a multicast addr
to team (which does not hold rtnl lock). Team syncs veth addrs,
but because veths' unicast list still has the duplicate it will
also get sync, even though this update is intended for mc addresses.
Again, uc address updates need rtnl lock, boom.
Reported-by: syzbot+7a2ab2cdc14d134de553@syzkaller.appspotmail.com
Fixes: 406f42fa0d ("net-next: When a bond have a massive amount of VLANs with IPv6 addresses, performance of changing link state, attaching a VRF, changing an IPv6 address, etc. go down dramtically.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following flower filter fails to match non-PPP_IP{V6} packets
wrapped in PPP_SES protocol:
tc filter add dev eth0 ingress protocol ppp_ses flower \
action simple sdata hi64
The reason is that proto local variable is being set even when
FLOW_DISSECT_RET_OUT_BAD status is returned.
The fix is to avoid setting proto variable if the PPP protocol is unknown.
Signed-off-by: Boris Sukholitko <boris.sukholitko@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
