Patch series "New page table range API", v6.
This patchset changes the API used by the MM to set up page table entries.
The four APIs are:
set_ptes(mm, addr, ptep, pte, nr)
update_mmu_cache_range(vma, addr, ptep, nr)
flush_dcache_folio(folio)
flush_icache_pages(vma, page, nr)
flush_dcache_folio() isn't technically new, but no architecture
implemented it, so I've done that for them. The old APIs remain around
but are mostly implemented by calling the new interfaces.
The new APIs are based around setting up N page table entries at once.
The N entries belong to the same PMD, the same folio and the same VMA, so
ptep++ is a legitimate operation, and locking is taken care of for you.
Some architectures can do a better job of it than just a loop, but I have
hesitated to make too deep a change to architectures I don't understand
well.
One thing I have changed in every architecture is that PG_arch_1 is now a
per-folio bit instead of a per-page bit when used for dcache clean/dirty
tracking. This was something that would have to happen eventually, and it
makes sense to do it now rather than iterate over every page involved in a
cache flush and figure out if it needs to happen.
The point of all this is better performance, and Fengwei Yin has measured
improvement on x86. I suspect you'll see improvement on your architecture
too. Try the new will-it-scale test mentioned here:
https://lore.kernel.org/linux-mm/20230206140639.538867-5-fengwei.yin@intel.com/
You'll need to run it on an XFS filesystem and have
CONFIG_TRANSPARENT_HUGEPAGE set.
This patchset is the basis for much of the anonymous large folio work
being done by Ryan, so it's received quite a lot of testing over the last
few months.
This patch (of 38):
Determine if a value lies within a range more efficiently (subtraction +
comparison vs two comparisons and an AND). It also has useful (under some
circumstances) behaviour if the range exceeds the maximum value of the
type. Convert all the conflicting definitions of in_range() within the
kernel; some can use the generic definition while others need their own
definition.
Link: https://lkml.kernel.org/r/20230802151406.3735276-1-willy@infradead.org
Link: https://lkml.kernel.org/r/20230802151406.3735276-2-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Fixes for v6.5-rc4
Display:
+ Fix to correct the UBWC programming for decoder version 4.3 seen
on SM8550
+ Add the missing flush and fetch bits for DMA4 and DMA5 SSPPs.
+ Fix to drop the unused dpu_core_perf_data_bus_id enum from the code
+ Drop the unused dsi_phy_14nm_17mA_regulators from QCM 2290 DSI cfg.
GPU:
+ Fix warn splat for newer devices without revn
+ Remove name/revn for a690.. we shouldn't be populating these for
newer devices, for consistency, but it slipped through review
+ Fix a6xx gpu snapshot BINDLESS_DATA size (was listed in bytes
instead of dwords, causing AHB faults on a6xx gen4/a660-family)
+ Disallow submit with fence id 0
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGs9MwCSfiyv8i7yWAsJKYEzCDyzaTx=ujX80Y23rZd9RA@mail.gmail.com
A fence id of zero is expected to be invalid, and is not removed from
the fence_idr table. If userspace is requesting to specify the fence
id with the FENCE_SN_IN flag, we need to reject a zero fence id value.
Fixes: 17154addc5 ("drm/msm: Add MSM_SUBMIT_FENCE_SN_IN")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/549180/
In an error path where the submit is free'd without the job being run,
the hw_fence pointer is simply a kzalloc'd block of memory. In this
case we should just kfree() it, rather than trying to decrement it's
reference count. Fortunately we can tell that this is the case by
checking for a zero refcount, since if the job was run, the submit would
be holding a reference to the hw_fence.
Fixes: f94e6a51e1 ("drm/msm: Pre-allocate hw_fence")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/547088/
The msm_gem_get_vaddr() returns an ERR_PTR() on failure, and a null
is catastrophic here, so we should use IS_ERR_OR_NULL() to check
the return value.
Fixes: 6a8bd08d04 ("drm/msm: add sudo flag to submit ioctl")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/547712/
Signed-off-by: Rob Clark <robdclark@chromium.org>
These fields are deprecated. But any userspace new enough to support
a690 also knows how to identify the GPU based on chip-id.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/545552/
Recently, a WARN_ON() was introduced to ensure that revn is filled before
adreno_is_aXYZ is called. This however doesn't work very well when revn is
0 by design (such as for A635).
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Fixes: cc943f43ec ("drm/msm/adreno: warn if chip revn is verified before being set")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Abhinav Kumar <quic_abhinavk@quicinc.com> # sc7280
Patchwork: https://patchwork.freedesktop.org/patch/545554/
The regulator setup was likely copied from other SoCs by mistake. Just
like SM6125 the DSI PHY on this platform is not getting power from a
regulator but from the MX power domain.
Fixes: 572e9fd6d1 ("drm/msm/dsi: Add phy configuration for QCM2290")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/544536/
Link: https://lore.kernel.org/r/20230627-sm6125-dpu-v2-1-03e430a2078c@somainline.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Note that with this, DMA4/DMA5 are still non-functional, but at least
display *something* in modetest instead of nothing or underflow.
Fixes: efcd010772 ("drm/msm/dpu: add support for SM8550")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Patchwork: https://patchwork.freedesktop.org/patch/545548/
Link: https://lore.kernel.org/r/20230704160106.26055-1-jonathan@marek.ca
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Generate a hotplug event after registering a client to allow the
client to configure its display. Remove the hotplug calls from the
existing clients for fbdev emulation. This change fixes a concurrency
bug between registering a client and receiving events from the DRM
core. The bug is present in the fbdev emulation of all drivers.
The fbdev emulation currently generates a hotplug event before
registering the client to the device. For each new output, the DRM
core sends an additional hotplug event to each registered client.
If the DRM core detects first output between sending the artificial
hotplug and registering the device, the output's hotplug event gets
lost. If this is the first output, the fbdev console display remains
dark. This has been observed with amdgpu and fbdev-generic.
Fix this by adding hotplug generation directly to the client's
register helper drm_client_register(). Registering the client and
receiving events are serialized by struct drm_device.clientlist_mutex.
So an output is either configured by the initial hotplug event, or
the client has already been registered.
The bug was originally added in commit 6e3f17ee73 ("drm/fb-helper:
generic: Call drm_client_add() after setup is done"), in which adding
a client and receiving a hotplug event switched order. It was hidden,
as most hardware and drivers have at least on static output configured.
Other drivers didn't use the internal DRM client or still had struct
drm_mode_config_funcs.output_poll_changed set. That callback handled
hotplug events as well. After not setting the callback in amdgpu in
commit 0e3172bac3 ("drm/amdgpu: Don't set struct
drm_driver.output_poll_changed"), amdgpu did not show a framebuffer
console if output events got lost. The bug got copy-pasted from
fbdev-generic into the other fbdev emulation.
Reported-by: Moritz Duge <MoritzDuge@kolahilft.de>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2649
Fixes: 6e3f17ee73 ("drm/fb-helper: generic: Call drm_client_add() after setup is done")
Fixes: 8ab59da26b ("drm/fb-helper: Move generic fbdev emulation into separate source file")
Fixes: b79fe9abd5 ("drm/fbdev-dma: Implement fbdev emulation for GEM DMA helpers")
Fixes: 63c381552f ("drm/armada: Implement fbdev emulation as in-kernel client")
Fixes: 49953b70e7 ("drm/exynos: Implement fbdev emulation as in-kernel client")
Fixes: 8f1aaccb04 ("drm/gma500: Implement client-based fbdev emulation")
Fixes: 940b869c2f ("drm/msm: Implement fbdev emulation as in-kernel client")
Fixes: 9e69bcd88e ("drm/omapdrm: Implement fbdev emulation as in-kernel client")
Fixes: e317a69fe8 ("drm/radeon: Implement client-based fbdev emulation")
Fixes: 71ec16f45e ("drm/tegra: Implement fbdev emulation as in-kernel client")
Fixes: 0e3172bac3 ("drm/amdgpu: Don't set struct drm_driver.output_poll_changed")
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Moritz Duge <MoritzDuge@kolahilft.de>
Tested-by: Torsten Krah <krah.tm@gmail.com>
Tested-by: Paul Schyska <pschyska@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@gmail.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Mikko Perttunen <mperttunen@nvidia.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.2+
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # msm
Link: https://patchwork.freedesktop.org/patch/msgid/20230710091029.27503-1-tzimmermann@suse.de
A610 is implemented on at least three SoCs: SM6115 (bengal), SM6125
(trinket) and SM6225 (khaje). Trinket does not support speed binning
(only a single SKU exists) and we don't yet support khaje upstream.
Hence, add a fuse mapping table for bengal to allow for per-chip
frequency limiting.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542780/
Signed-off-by: Rob Clark <robdclark@chromium.org>
A619_holi is implemented on at least two SoCs: SM4350 (holi) and SM6375
(blair). This is what seems to be a first occurrence of this happening,
but it's easy to overcome by guarding the SoC-specific fuse values with
of_machine_is_compatible(). Do just that to enable frequency limiting
on these SoCs.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542772/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Before transitioning to using per-SoC and not per-Adreno speedbin
fuse values (need another patchset to land elsewhere), a good
improvement/stopgap solution is to use adreno_is_aXYZ macros in
place of explicit revision matching. Do so to allow differentiating
between A619 and A619_holi.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542777/
Signed-off-by: Rob Clark <robdclark@chromium.org>
The GPU can only be one at a time. Turn a series of ifs into if +
elseifs to save some CPU cycles.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542770/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Adreno 619 expects some tunables to be set differently. Make up for it.
Fixes: b7616b5c69 ("drm/msm/adreno: Add A619 support")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542782/
Signed-off-by: Rob Clark <robdclark@chromium.org>
A610 is one of (if not the) lowest-tier SKUs in the A6XX family. It
features no GMU, as it's implemented solely on SoCs with SMD_RPM.
What's more interesting is that it does not feature a VDDGX line
either, being powered solely by VDDCX and has an unfortunate hardware
quirk that makes its reset line broken - after a couple of assert/
deassert cycles, it will hang for good and will not wake up again.
This GPU requires mesa changes for proper rendering, and lots of them
at that. The command streams are quite far away from any other A6XX
GPU and hence it needs special care. This patch was validated both
by running an (incomplete) downstream mesa with some hacks (frames
rendered correctly, though some instructions made the GPU hangcheck
which is expected - garbage in, garbage out) and by replaying RD
traces captured with the downstream KGSL driver - no crashes there,
ever.
Add support for this GPU on the kernel side, which comes down to
pretty simply adding A612 HWCG tables, altering a few values and
adding a special case for handling the reset line.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542779/
Signed-off-by: Rob Clark <robdclark@chromium.org>
A619_holi is a GMU-less variant of the already-supported A619 GPU.
It's present on at least SM4350 (holi) and SM6375 (blair). No mesa
changes are required. Add the required kernel-side support for it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542775/
Signed-off-by: Rob Clark <robdclark@chromium.org>
A610 and A619_holi don't support the feature. Disable it to make the GPU stop
crashing after almost each and every submission - the received data on
the GPU end was simply incomplete in garbled, resulting in almost nothing
being executed properly. Extend the disablement to adreno_has_gmu_wrapper,
as none of the GMU wrapper Adrenos that don't support yet seem to feature it.
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542774/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Some (particularly SMD_RPM, a.k.a non-RPMh) SoCs implement A6XX GPUs
but don't implement the associated GMUs. This is due to the fact that
the GMU directly pokes at RPMh. Sadly, this means we have to take care
of enabling & scaling power rails, clocks and bandwidth ourselves.
Reuse existing Adreno-common code and modify the deeply-GMU-infused
A6XX code to facilitate these GPUs. This involves if-ing out lots
of GMU callbacks and introducing a new type of GMU - GMU wrapper (it's
the actual name that Qualcomm uses in their downstream kernels).
This is essentially a register region which is convenient to model
as a device. We'll use it for managing the GDSCs. The register
layout matches the actual GMU_CX/GX regions on the "real GMU" devices
and lets us reuse quite a bit of gmu_read/write/rmw calls.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542766/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Since the introduction of A6xx support, we've been enabling the CX GMU
power counter 0 in a bit of a weird spot. Move it to hw_init so that
GMU wrapper GPUs can reuse the same code paths. As a bonus, this order
makes it easier to compare mainline and downstream register access traces.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542765/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Rename lower_bit to hbb_lo and explain what it signifies.
Add explanations (wherever possible to other tunables).
Port setting min_access_length, ubwc_mode and hbb_hi from downstream.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542764/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Currently we're only deasserting REG_A6XX_RBBM_GBIF_HALT, but we also
need REG_A6XX_GBIF_HALT to be set to 0.
This is typically done automatically on successful GX collapse, but in
case that fails, we should take care of it.
Also, add a memory barrier to ensure it's gone through before jumping
to further initialization.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542760/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Introduce a6xx_gpu_sw_reset() in preparation for adding GMU wrapper
GPUs and reuse it in a6xx_gmu_force_off().
This helper, contrary to the original usage in GMU code paths, adds
a readback+delay sequence to ensure that the reset is never deasserted
too quickly due to e.g. OoO execution going crazy.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542758/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Unify the indentation and explain the cryptic 0xF value.
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542756/
Signed-off-by: Rob Clark <robdclark@chromium.org>
This function is responsible for telling the GPU to halt transactions
on all of its relevant buses, drain them and leave them in a predictable
state, so that the GPU can be e.g. reset cleanly.
Move the function to a6xx_gpu.c, remove the static keyword and add a
prototype in a6xx_gpu.h to accomodate for the move.
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542762/
Signed-off-by: Rob Clark <robdclark@chromium.org>
As pointed out by Akhil during the review process of GMU wrapper
introduction [1], it makes sense to move this write into the function
that's responsible for forcibly shutting the GMU off.
It is also very convenient to move this to GMU-specific code, so that
it does not have to be guarded by an if-condition to avoid calling it
on GMU wrapper targets.
Move the write to the aforementioned a6xx_gmu_force_off() to achieve
that. No effective functional change.
[1] https://lore.kernel.org/linux-arm-msm/20230501194022.GA18382@akhilpo-linux.qualcomm.com/
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542752/
Signed-off-by: Rob Clark <robdclark@chromium.org>
These two will be reused by at least A619_holi in the non-gmu
paths. Turn them non-static them to make it possible.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542751/
Signed-off-by: Rob Clark <robdclark@chromium.org>
The adreno_is_revn rework came at the same time as A690 introduction
and that resulted in it not covering all cases. Fix it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542754/
Signed-off-by: Rob Clark <robdclark@chromium.org>
During IRQ conversion we have lost the PP_DONE interrupts for sc7280
platform. This was left unnoticed, because this interrupt is only used
for CMD outputs and probably no sc7[12]80 systems use DSI CMD panels.
Fixes: 667e9985ee ("drm/msm/dpu: replace IRQ lookup with the data in hw catalog")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/542175/
Link: https://lore.kernel.org/r/20230613001004.3426676-2-dmitry.baryshkov@linaro.org
The DP component's unbind operation walks through the submodules to
unregister and clean things up. But if the unbind happens because the DP
controller itself is being removed, all the memory for those submodules
has just been freed.
Change the order of these operations to avoid the many use-after-free
that otherwise happens in this code path.
Fixes: c943b4948b ("drm/msm/dp: add displayPort driver support")
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/542166/
Link: https://lore.kernel.org/r/20230612220259.1884381-1-quic_bjorande@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Using devres to depopulate the aux bus made sure that upon a probe
deferral the EDP panel device would be destroyed and recreated upon next
attempt.
But the struct device which the devres is tied to is the DPUs
(drm_dev->dev), which may be happen after the DP controller is torn
down.
Indications of this can be seen in the commonly seen EDID-hexdump full
of zeros in the log, or the occasional/rare KASAN fault where the
panel's attempt to read the EDID information causes a use after free on
DP resources.
It's tempting to move the devres to the DP controller's struct device,
but the resources used by the device(s) on the aux bus are explicitly
torn down in the error path. The KASAN-reported use-after-free also
remains, as the DP aux "module" explicitly frees its devres-allocated
memory in this code path.
As such, explicitly depopulate the aux bus in the error path, and in the
component unbind path, to avoid these issues.
Fixes: 2b57f72661 ("drm/msm/dp: fix aux-bus EP lifetime")
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/542163/
Link: https://lore.kernel.org/r/20230612220106.1884039-1-quic_bjorande@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Since commit 93e81e38e1 ("drm/fb_helper: Minimize damage-helper
overhead") the drm_fb_helper_funcs::fb_dirty helper is required for
proper dirty/damage processing. The drm/msm driver requires that to
function to let CMD panels to work. Use simplified version of
drm_fbdev_generic_helper_fb_dirty() to fix support for CMD mode panels.
Reported-by: Degdag Mohamed <degdagmohamed@gmail.com>
Fixes: 93e81e38e1 ("drm/fb_helper: Minimize damage-helper overhead")
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/542002/
Link: https://lore.kernel.org/r/20230612031616.3620134-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Currently, slice_count is being used to calculate word count and
pkt_per_line. Instead, these values should be calculated using slice per
packet, which is not the same as slice_count.
Slice count represents the number of slices per interface, and its value
will not always match that of slice per packet. For example, it is possible
to have cases where there are multiple slices per interface but the panel
specifies only one slice per packet.
Thus, use the default value of one slice per packet and remove slice_count
from the aforementioned calculations.
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Fixes: bc6b6ff813 ("drm/msm/dsi: Use DSC slice(s) packet size to compute word count")
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/541965/
Link: https://lore.kernel.org/r/20230405-add-dsc-support-v6-5-95eab864d1b6@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Add a DPU INTF op to set the DCE_DATA_COMPRESS bit to enable the
DCE/DSC 1.2 datapath
Note: For now, this op is called for command mode encoders only. Changes to
set DATA_COMPRESS for video mode encoders will be posted along with DSC
v1.2 support for DP.
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/541966/
Link: https://lore.kernel.org/r/20230405-add-dsc-support-v6-4-95eab864d1b6@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
In DPU 7.x and later, DSC/DCE enablement registers have been moved from
PINGPONG to INTF. Thus, add a DPU_INTF_DATA_COMPRESS feature flag that will
be set if the DATA_COMPRESS register is in the INTF block.
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/541967/
Link: https://lore.kernel.org/r/20230405-add-dsc-support-v6-3-95eab864d1b6@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Currently, when compression is enabled, hdisplay is reduced via integer
division. This causes issues for modes where the original hdisplay is
not a multiple of 3.
To fix this, use DIV_ROUND_UP to divide hdisplay.
Suggested-by: Marijn Suijten <marijn.suijten@somainline.org>
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/541970/
Link: https://lore.kernel.org/r/20230405-add-dsc-support-v6-1-95eab864d1b6@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Add DSC 1.2 hardware blocks to the catalog with necessary sub-block and
feature flag information. Each display compression engine (DCE) contains
dual DSC encoders so both share same base address but with its own
different sub block address.
changes in v4:
-- delete DPU_DSC_HW_REV_1_1
-- re arrange sc8280xp_dsc[]
changes in v4:
-- fix checkpatch warning
changes in v10:
-- remove hard slice from commit text
-- replace DPU_DSC_NATIVE_422_EN with DPU_DSC_NATIVE_42x_EN
-- change DSC_BLK_1_2 .len from 0x100 to 0x29c
changes in v11:
-- remove comment at DSC_BLK_1_2 marco
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/539507/
Link: https://lore.kernel.org/r/1685036458-22683-10-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Add support for DSC 1.2 by providing the necessary hooks to program
the DPU DSC 1.2 encoder.
Changes in v3:
-- fixed kernel test rebot report that "__iomem *off" is declared but not
used at dpu_hw_dsc_config_1_2()
-- unrolling thresh loops
Changes in v4:
-- delete DPU_DSC_HW_REV_1_1
-- delete off and used real register name directly
Changes in v7:
-- replace offset with sblk->enc.base
-- replace ss with slice
Changes in v8:
-- fixed checkpatch warning
Changes in v9:
-- replaced __dsc_calc_ob_max_addr() with __dsc_calc_output_buf_max_addr()
-- replaced variable num_ss with num_softslice
-- remove inline from function declaration
changes in v10:
-- rewording text of changes in v9
-- replace DPU_DSC_NATIVE_422_EN with DPU_DSC_NATIVE_42x_EN
-- replace drm_dsc_calculate_flatness_det_thresh() with drm_dsc_flatness_det_thresh()
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/539500/
Link: https://lore.kernel.org/r/1685036458-22683-7-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Currently, hdisplay is being divided by 3 for DSC. However, this
calculation only works for cases where BPP = 8.
Update hdisplay calculation to be bytes_per_line / 3, so that it
accounts for cases where BPP != 8.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/539271/
Link: https://lore.kernel.org/r/20230329-rfc-msm-dsc-helper-v14-9-bafc7be95691@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The current dpu_hw_dsc calculation for det_thresh_flatness does not
match the downstream calculation or the DSC spec.
Use the DRM DSC helper for det_thresh_flatness to match downstream
implementation and the DSC spec.
Fixes: c110cfd175 ("drm/msm/disp/dpu1: Add support for DSC")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/539275/
Link: https://lore.kernel.org/r/20230329-rfc-msm-dsc-helper-v14-6-bafc7be95691@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Matthew Wilcox (Oracle)