When the ax25 device is detaching, the ax25_dev_device_down()
calls ax25_ds_del_timer() to cleanup the slave_timer. When
the timer handler is running, the ax25_ds_del_timer() that
calls del_timer() in it will return directly. As a result,
the use-after-free bugs could happen, one of the scenarios
is shown below:
(Thread 1) | (Thread 2)
| ax25_ds_timeout()
ax25_dev_device_down() |
ax25_ds_del_timer() |
del_timer() |
ax25_dev_put() //FREE |
| ax25_dev-> //USE
In order to mitigate bugs, when the device is detaching, use
timer_shutdown_sync() to stop the timer.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240329015023.9223-1-duoming@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 73d9629e1c ("i40e: Do not allow untrusted VF to remove
administratively set MAC") fixed an issue where untrusted VF was
allowed to remove its own MAC address although this was assigned
administratively from PF. Unfortunately the introduced check
is wrong because it causes that MAC filters for other MAC addresses
including multi-cast ones are not removed.
<snip>
if (ether_addr_equal(addr, vf->default_lan_addr.addr) &&
i40e_can_vf_change_mac(vf))
was_unimac_deleted = true;
else
continue;
if (i40e_del_mac_filter(vsi, al->list[i].addr)) {
...
</snip>
The else path with `continue` effectively skips any MAC filter
removal except one for primary MAC addr when VF is allowed to do so.
Fix the check condition so the `continue` is only done for primary
MAC address.
Fixes: 73d9629e1c ("i40e: Do not allow untrusted VF to remove administratively set MAC")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240329180638.211412-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Matthieu Baerts says:
====================
mptcp: fix fallback MIB counter and wrong var in selftests
Here are two fixes related to MPTCP.
The first patch fixes when the MPTcpExtMPCapableFallbackACK MIB counter
is modified: it should only be incremented when a connection was using
MPTCP options, but then a fallback to TCP has been done. This patch also
checks the counter is not incremented by mistake during the connect
selftests. This counter was wrongly incremented since its introduction
in v5.7.
The second patch fixes a wrong parsing of the 'dev' endpoint options in
the selftests: the wrong variable was used. This option was not used
before, but it is going to be soon. This issue is visible since v5.18.
====================
Link: https://lore.kernel.org/r/20240329-upstream-net-20240329-fallback-mib-v1-0-324a8981da48@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There's a bug in pm_nl_check_endpoint(), 'dev' didn't be parsed correctly.
If calling it in the 2nd test of endpoint_tests() too, it fails with an
error like this:
creation [FAIL] expected '10.0.2.2 id 2 subflow dev dev' \
found '10.0.2.2 id 2 subflow dev ns2eth2'
The reason is '$2' should be set to 'dev', not '$1'. This patch fixes it.
Fixes: 69c6ce7b6e ("selftests: mptcp: add implicit endpoint test case")
Cc: stable@vger.kernel.org
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240329-upstream-net-20240329-fallback-mib-v1-2-324a8981da48@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current MPTCP servers increment MPTcpExtMPCapableFallbackACK when they
accept non-MPC connections. As reported by Christoph, this is "surprising"
because the counter might become greater than MPTcpExtMPCapableSYNRX.
MPTcpExtMPCapableFallbackACK counter's name suggests it should only be
incremented when a connection was seen using MPTCP options, then a
fallback to TCP has been done. Let's do that by incrementing it when
the subflow context of an inbound MPC connection attempt is dropped.
Also, update mptcp_connect.sh kselftest, to ensure that the
above MIB does not increment in case a pure TCP client connects to a
MPTCP server.
Fixes: fc518953bc ("mptcp: add and use MIB counter infrastructure")
Cc: stable@vger.kernel.org
Reported-by: Christoph Paasch <cpaasch@apple.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/449
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240329-upstream-net-20240329-fallback-mib-v1-1-324a8981da48@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The netdev CI runs in a VM and captures serial, so stdout and
stderr get combined. Because there's a missing new line in
stderr the test ends up corrupting KTAP:
# Successok 1 selftests: net: reuseaddr_conflict
which should have been:
# Success
ok 1 selftests: net: reuseaddr_conflict
Fixes: 422d8dc6fd ("selftest: add a reuseaddr test")
Reviewed-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Link: https://lore.kernel.org/r/20240329160559.249476-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In lan8814_get_sig_rx() and lan8814_get_sig_tx() ptp_parse_header() may
return NULL as ptp_header due to abnormal packet type or corrupted packet.
Fix this bug by adding ptp_header check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: ece1950283 ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240329061631.33199-1-amishin@t-argos.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Bluetooth: Fix TOCTOU in HCI debugfs implementation
- Bluetooth: hci_event: set the conn encrypted before conn establishes
- Bluetooth: qca: fix device-address endianness
- Bluetooth: hci_sync: Fix not checking error on hci_cmd_sync_cancel_sync
-----BEGIN PGP SIGNATURE-----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=tCQe
-----END PGP SIGNATURE-----
Merge tag 'for-net-2024-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- Bluetooth: Fix TOCTOU in HCI debugfs implementation
- Bluetooth: hci_event: set the conn encrypted before conn establishes
- Bluetooth: qca: fix device-address endianness
- Bluetooth: hci_sync: Fix not checking error on hci_cmd_sync_cancel_sync
* tag 'for-net-2024-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: Fix TOCTOU in HCI debugfs implementation
Bluetooth: hci_event: set the conn encrypted before conn establishes
Bluetooth: hci_sync: Fix not checking error on hci_cmd_sync_cancel_sync
Bluetooth: qca: fix device-address endianness
Bluetooth: add quirk for broken address properties
arm64: dts: qcom: sc7180-trogdor: mark bluetooth address as broken
dt-bindings: bluetooth: add 'qcom,local-bd-address-broken'
Revert "Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT"
====================
Link: https://lore.kernel.org/r/20240329140453.2016486-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kuniyuki Iwashima says:
====================
tcp: Fix bind() regression and more tests.
bhash2 has not been well tested for IPV6_V6ONLY option.
This series fixes two regression around IPV6_V6ONLY, one of which
has been there since bhash2 introduction, and another is introduced
by a recent change.
Also, this series adds as many tests as possible to catch regression
easily. The baseline is 28044fc1d495~ which is pre-bhash2 commit.
Tested on 28044fc1d495~:
# PASSED: 132 / 132 tests passed.
# Totals: pass:132 fail:0 xfail:0 xpass:0 skip:0 error:0
net.git:
# FAILED: 125 / 132 tests passed.
# Totals: pass:125 fail:7 xfail:0 xpass:0 skip:0 error:0
With this series:
# PASSED: 132 / 132 tests passed.
# Totals: pass:132 fail:0 xfail:0 xpass:0 skip:0 error:0
v1: https://lore.kernel.org/netdev/20240325181923.48769-1-kuniyu@amazon.com/
====================
Link: https://lore.kernel.org/r/20240326204251.51301-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds two tests using SO_REUSEADDR and SO_REUSEPORT and
defines errno for each test case.
SO_REUSEADDR/SO_REUSEPORT is set for the per-fixture two bind()
calls.
The notable pattern is the pair of v6only [::] and plain [::].
The two sockets are put into the same tb2, where per-bucket v6only
flag would be useless to detect bind() conflict.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240326204251.51301-9-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bhash2 was not well tested for IPv6-only sockets.
This patch adds test cases where we set IPV6_V6ONLY for per-fixture
bind() calls if variant->ipv6_only[i] is true.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240326204251.51301-8-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In addtition to the two addresses defined in the fixtures, this patch
add 6 more bind calls():
* 0.0.0.0
* 127.0.0.1
* ::
* ::1
* ::ffff:0.0.0.0
* ::ffff:127.0.0.1
The first two per-fixture bind() calls control how inet_bind2_bucket
is created, and the rest 6 bind() calls cover as many conflicting
patterns as possible.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240326204251.51301-7-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We don't have bind() conflict tests for the same protocol pairs.
Let's add them except for the same address pair, which will be
covered by the following patch adding 6 more bind() calls for
each test case.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240326204251.51301-6-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, bind_wildcard.c calls bind() twice for two addresses and
checks the pre-defined errno against the 2nd call. Also, the two
bind() calls are swapped to cover various patterns how bind buckets
are created.
However, only testing two addresses is insufficient to detect regression.
So, we will add more bind() calls, and then, we need to define different
errno for each bind() per test case.
As a prepartion, let's define the reverse order bind() test cases as
fixtures.
No functional changes are intended.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240326204251.51301-5-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, bind_wildcard.c tests only (IPv4, IPv6) pairs, but we will
add more tests for the same protocol pairs.
This patch makes it possible by changing the address pointer to void.
No functional changes are intended.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240326204251.51301-4-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jianguo Wu reported another bind() regression introduced by bhash2.
Calling bind() for the following 3 addresses on the same port, the
3rd one should fail but now succeeds.
1. 0.0.0.0 or ::ffff:0.0.0.0
2. [::] w/ IPV6_V6ONLY
3. IPv4 non-wildcard address or v4-mapped-v6 non-wildcard address
The first two bind() create tb2 like this:
bhash2 -> tb2(:: w/ IPV6_V6ONLY) -> tb2(0.0.0.0)
The 3rd bind() will match with the IPv6 only wildcard address bucket
in inet_bind2_bucket_match_addr_any(), however, no conflicting socket
exists in the bucket. So, inet_bhash2_conflict() will returns false,
and thus, inet_bhash2_addr_any_conflict() returns false consequently.
As a result, the 3rd bind() bypasses conflict check, which should be
done against the IPv4 wildcard address bucket.
So, in inet_bhash2_addr_any_conflict(), we must iterate over all buckets.
Note that we cannot add ipv6_only flag for inet_bind2_bucket as it
would confuse the following patetrn.
1. [::] w/ SO_REUSE{ADDR,PORT} and IPV6_V6ONLY
2. [::] w/ SO_REUSE{ADDR,PORT}
3. IPv4 non-wildcard address or v4-mapped-v6 non-wildcard address
The first bind() would create a bucket with ipv6_only flag true,
the second bind() would add the [::] socket into the same bucket,
and the third bind() could succeed based on the wrong assumption
that ipv6_only bucket would not conflict with v4(-mapped-v6) address.
Fixes: 28044fc1d4 ("net: Add a bhash2 table hashed by port and address")
Diagnosed-by: Jianguo Wu <wujianguo106@163.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240326204251.51301-3-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 5e07e67241 ("tcp: Use bhash2 for v4-mapped-v6 non-wildcard
address.") introduced bind() regression for v4-mapped-v6 address.
When we bind() the following two addresses on the same port, the 2nd
bind() should succeed but fails now.
1. [::] w/ IPV6_ONLY
2. ::ffff:127.0.0.1
After the chagne, v4-mapped-v6 uses bhash2 instead of bhash to
detect conflict faster, but I forgot to add a necessary change.
During the 2nd bind(), inet_bind2_bucket_match_addr_any() returns
the tb2 bucket of [::], and inet_bhash2_conflict() finally calls
inet_bind_conflict(), which returns true, meaning conflict.
inet_bhash2_addr_any_conflict
|- inet_bind2_bucket_match_addr_any <-- return [::] bucket
`- inet_bhash2_conflict
`- __inet_bhash2_conflict <-- checks IPV6_ONLY for AF_INET
| but not for v4-mapped-v6 address
`- inet_bind_conflict <-- does not check address
inet_bind_conflict() does not check socket addresses because
__inet_bhash2_conflict() is expected to do so.
However, it checks IPV6_V6ONLY attribute only against AF_INET
socket, and not for v4-mapped-v6 address.
As a result, v4-mapped-v6 address conflicts with v6-only wildcard
address.
To avoid that, let's add the missing test to use bhash2 for
v4-mapped-v6 address.
Fixes: 5e07e67241 ("tcp: Use bhash2 for v4-mapped-v6 non-wildcard address.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240326204251.51301-2-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On devices that support DASH, the current code in the "rtl_loop_wait" function
raises false alarms when DASH is disabled. This occurs because the function
attempts to wait for the DASH firmware to be ready, even though it's not
relevant in this case.
r8169 0000:0c:00.0 eth0: RTL8168ep/8111ep, 38:7c:76:49:08:d9, XID 502, IRQ 86
r8169 0000:0c:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko]
r8169 0000:0c:00.0 eth0: DASH disabled
...
r8169 0000:0c:00.0 eth0: rtl_ep_ocp_read_cond == 0 (loop: 30, delay: 10000).
This patch modifies the driver start/stop functions to skip checking the DASH
firmware status when DASH is explicitly disabled. This prevents unnecessary
delays and false alarms.
The patch has been tested on several ThinkStation P8/PX workstations.
Fixes: 0ab0c45d8a ("r8169: add handling DASH when DASH is disabled")
Signed-off-by: Atlas Yu <atlas.yu@canonical.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20240328055152.18443-1-atlas.yu@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
otx2_rxtx_enable() return negative error code such as -EIO,
check -EIO rather than EIO to fix this problem.
Fixes: c926252205 ("octeontx2-pf: Disable packet I/O for graceful exit")
Signed-off-by: Su Hui <suhui@nfschina.com>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://lore.kernel.org/r/20240328020620.4054692-1-suhui@nfschina.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no reason to consume a full cacheline to store system_page_pool.
We can eventually move it to softnet_data later for full locality control.
Fixes: 2b0cfa6e49 ("net: add generic percpu page_pool allocator")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/20240328173448.2262593-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-03-26 (i40e)
This series contains updates to i40e driver only.
Ivan Vecera resolves an issue where descriptors could be missed when
exiting busy poll.
Aleksandr corrects counting of MAC filters to only include new or active
filters and resolves possible use of incorrect/stale 'vf' variable.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: fix vf may be used uninitialized in this function warning
i40e: fix i40e_count_filters() to count only active/new filters
i40e: Enforce software interrupt during busy-poll exit
====================
Link: https://lore.kernel.org/r/20240326162358.1224145-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
cp might be null, calling cp->cp_conn would produce null dereference
[Simon Horman adds:]
Analysis:
* cp is a parameter of __rds_rdma_map and is not reassigned.
* The following call-sites pass a NULL cp argument to __rds_rdma_map()
- rds_get_mr()
- rds_get_mr_for_dest
* Prior to the code above, the following assumes that cp may be NULL
(which is indicative, but could itself be unnecessary)
trans_private = rs->rs_transport->get_mr(
sg, nents, rs, &mr->r_key, cp ? cp->cp_conn : NULL,
args->vec.addr, args->vec.bytes,
need_odp ? ODP_ZEROBASED : ODP_NOT_NEEDED);
* The code modified by this patch is guarded by IS_ERR(trans_private),
where trans_private is assigned as per the previous point in this analysis.
The only implementation of get_mr that I could locate is rds_ib_get_mr()
which can return an ERR_PTR if the conn (4th) argument is NULL.
* ret is set to PTR_ERR(trans_private).
rds_ib_get_mr can return ERR_PTR(-ENODEV) if the conn (4th) argument is NULL.
Thus ret may be -ENODEV in which case the code in question will execute.
Conclusion:
* cp may be NULL at the point where this patch adds a check;
this patch does seem to address a possible bug
Fixes: c055fc00c0 ("net/rds: fix WARNING in rds_conn_connect_if_down")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Mahmoud Adam <mngyadam@amazon.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240326153132.55580-1-mngyadam@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The switch has 4 ports with 2 internal PHYs, but ports are numbered up
to 6, with ports 0, 1, 5 and 6 being usable.
Fixes: 71d94a432a ("net: dsa: mv88e6xxx: add support for MV88E6020 switch")
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240326123655.40666-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The mlxbf_gige driver intermittantly encounters a NULL pointer
exception while the system is shutting down via "reboot" command.
The mlxbf_driver will experience an exception right after executing
its shutdown() method. One example of this exception is:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000070
Mem abort info:
ESR = 0x0000000096000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x04: level 0 translation fault
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=000000011d373000
[0000000000000070] pgd=0000000000000000, p4d=0000000000000000
Internal error: Oops: 96000004 [#1] SMP
CPU: 0 PID: 13 Comm: ksoftirqd/0 Tainted: G S OE 5.15.0-bf.6.gef6992a #1
Hardware name: https://www.mellanox.com BlueField SoC/BlueField SoC, BIOS 4.0.2.12669 Apr 21 2023
pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : mlxbf_gige_handle_tx_complete+0xc8/0x170 [mlxbf_gige]
lr : mlxbf_gige_poll+0x54/0x160 [mlxbf_gige]
sp : ffff8000080d3c10
x29: ffff8000080d3c10 x28: ffffcce72cbb7000 x27: ffff8000080d3d58
x26: ffff0000814e7340 x25: ffff331cd1a05000 x24: ffffcce72c4ea008
x23: ffff0000814e4b40 x22: ffff0000814e4d10 x21: ffff0000814e4128
x20: 0000000000000000 x19: ffff0000814e4a80 x18: ffffffffffffffff
x17: 000000000000001c x16: ffffcce72b4553f4 x15: ffff80008805b8a7
x14: 0000000000000000 x13: 0000000000000030 x12: 0101010101010101
x11: 7f7f7f7f7f7f7f7f x10: c2ac898b17576267 x9 : ffffcce720fa5404
x8 : ffff000080812138 x7 : 0000000000002e9a x6 : 0000000000000080
x5 : ffff00008de3b000 x4 : 0000000000000000 x3 : 0000000000000001
x2 : 0000000000000000 x1 : 0000000000000000 x0 : 0000000000000000
Call trace:
mlxbf_gige_handle_tx_complete+0xc8/0x170 [mlxbf_gige]
mlxbf_gige_poll+0x54/0x160 [mlxbf_gige]
__napi_poll+0x40/0x1c8
net_rx_action+0x314/0x3a0
__do_softirq+0x128/0x334
run_ksoftirqd+0x54/0x6c
smpboot_thread_fn+0x14c/0x190
kthread+0x10c/0x110
ret_from_fork+0x10/0x20
Code: 8b070000 f9000ea0 f95056c0 f86178a1 (b9407002)
---[ end trace 7cc3941aa0d8e6a4 ]---
Kernel panic - not syncing: Oops: Fatal exception in interrupt
Kernel Offset: 0x4ce722520000 from 0xffff800008000000
PHYS_OFFSET: 0x80000000
CPU features: 0x000005c1,a3330e5a
Memory Limit: none
---[ end Kernel panic - not syncing: Oops: Fatal exception in interrupt ]---
During system shutdown, the mlxbf_gige driver's shutdown() is always executed.
However, the driver's stop() method will only execute if networking interface
configuration logic within the Linux distribution has been setup to do so.
If shutdown() executes but stop() does not execute, NAPI remains enabled
and this can lead to an exception if NAPI is scheduled while the hardware
interface has only been partially deinitialized.
The networking interface managed by the mlxbf_gige driver must be properly
stopped during system shutdown so that IFF_UP is cleared, the hardware
interface is put into a clean state, and NAPI is fully deinitialized.
Fixes: f92e1869d7 ("Add Mellanox BlueField Gigabit Ethernet driver")
Signed-off-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/20240325210929.25362-1-davthompson@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
struct hci_dev members conn_info_max_age, conn_info_min_age,
le_conn_max_interval, le_conn_min_interval, le_adv_max_interval,
and le_adv_min_interval can be modified from the HCI core code, as well
through debugfs.
The debugfs implementation, that's only available to privileged users,
will check for boundaries, making sure that the minimum value being set
is strictly above the maximum value that already exists, and vice-versa.
However, as both minimum and maximum values can be changed concurrently
to us modifying them, we need to make sure that the value we check is
the value we end up using.
For example, with ->conn_info_max_age set to 10, conn_info_min_age_set()
gets called from vfs handlers to set conn_info_min_age to 8.
In conn_info_min_age_set(), this goes through:
if (val == 0 || val > hdev->conn_info_max_age)
return -EINVAL;
Concurrently, conn_info_max_age_set() gets called to set to set the
conn_info_max_age to 7:
if (val == 0 || val > hdev->conn_info_max_age)
return -EINVAL;
That check will also pass because we used the old value (10) for
conn_info_max_age.
After those checks that both passed, the struct hci_dev access
is mutex-locked, disabling concurrent access, but that does not matter
because the invalid value checks both passed, and we'll end up with
conn_info_min_age = 8 and conn_info_max_age = 7
To fix this problem, we need to lock the structure access before so the
check and assignment are not interrupted.
This fix was originally devised by the BassCheck[1] team, and
considered the problem to be an atomicity one. This isn't the case as
there aren't any concerns about the variable changing while we check it,
but rather after we check it parallel to another change.
This patch fixes CVE-2024-24858 and CVE-2024-24857.
[1] https://sites.google.com/view/basscheck/
Co-developed-by: Gui-Dong Han <2045gemini@gmail.com>
Signed-off-by: Gui-Dong Han <2045gemini@gmail.com>
Link: https://lore.kernel.org/linux-bluetooth/20231222161317.6255-1-2045gemini@gmail.com/
Link: https://nvd.nist.gov/vuln/detail/CVE-2024-24858
Link: https://lore.kernel.org/linux-bluetooth/20231222162931.6553-1-2045gemini@gmail.com/
Link: https://lore.kernel.org/linux-bluetooth/20231222162310.6461-1-2045gemini@gmail.com/
Link: https://nvd.nist.gov/vuln/detail/CVE-2024-24857
Fixes: 31ad169148 ("Bluetooth: Add conn info lifetime parameters to debugfs")
Fixes: 729a1051da ("Bluetooth: Expose default LE advertising interval via debugfs")
Fixes: 71c3b60ec6 ("Bluetooth: Move BR/EDR debugfs file creation into hci_debugfs.c")
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
We have a BT headset (Lenovo Thinkplus XT99), the pairing and
connecting has no problem, once this headset is paired, bluez will
remember this device and will auto re-connect it whenever the device
is powered on. The auto re-connecting works well with Windows and
Android, but with Linux, it always fails. Through debugging, we found
at the rfcomm connection stage, the bluetooth stack reports
"Connection refused - security block (0x0003)".
For this device, the re-connecting negotiation process is different
from other BT headsets, it sends the Link_KEY_REQUEST command before
the CONNECT_REQUEST completes, and it doesn't send ENCRYPT_CHANGE
command during the negotiation. When the device sends the "connect
complete" to hci, the ev->encr_mode is 1.
So here in the conn_complete_evt(), if ev->encr_mode is 1, link type
is ACL and HCI_CONN_ENCRYPT is not set, we set HCI_CONN_ENCRYPT to
this conn, and update conn->enc_key_size accordingly.
After this change, this BT headset could re-connect with Linux
successfully. This is the btmon log after applying the patch, after
receiving the "Connect Complete" with "Encryption: Enabled", will send
the command to read encryption key size:
> HCI Event: Connect Request (0x04) plen 10
Address: 8C:3C:AA:D8:11:67 (OUI 8C-3C-AA)
Class: 0x240404
Major class: Audio/Video (headset, speaker, stereo, video, vcr)
Minor class: Wearable Headset Device
Rendering (Printing, Speaker)
Audio (Speaker, Microphone, Headset)
Link type: ACL (0x01)
...
> HCI Event: Link Key Request (0x17) plen 6
Address: 8C:3C:AA:D8:11:67 (OUI 8C-3C-AA)
< HCI Command: Link Key Request Reply (0x01|0x000b) plen 22
Address: 8C:3C:AA:D8:11:67 (OUI 8C-3C-AA)
Link key: ${32-hex-digits-key}
...
> HCI Event: Connect Complete (0x03) plen 11
Status: Success (0x00)
Handle: 256
Address: 8C:3C:AA:D8:11:67 (OUI 8C-3C-AA)
Link type: ACL (0x01)
Encryption: Enabled (0x01)
< HCI Command: Read Encryption Key... (0x05|0x0008) plen 2
Handle: 256
< ACL Data TX: Handle 256 flags 0x00 dlen 10
L2CAP: Information Request (0x0a) ident 1 len 2
Type: Extended features supported (0x0002)
> HCI Event: Command Complete (0x0e) plen 7
Read Encryption Key Size (0x05|0x0008) ncmd 1
Status: Success (0x00)
Handle: 256
Key size: 16
Cc: stable@vger.kernel.org
Link: https://github.com/bluez/bluez/issues/704
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_cmd_sync_cancel_sync shall check the error passed to it since it
will be propagated using req_result which is __u32 it needs to be
properly set to a positive value if it was passed as negative othertise
IS_ERR will not trigger as -(errno) would be converted to a positive
value.
Fixes: 63298d6e75 ("Bluetooth: hci_core: Cancel request on command timeout")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reported-and-tested-by: Thorsten Leemhuis <linux@leemhuis.info>
Closes: https://lore.kernel.org/all/08275279-7462-4f4a-a0ee-8aa015f829bc@leemhuis.info/
The WCN6855 firmware on the Lenovo ThinkPad X13s expects the Bluetooth
device address in big-endian order when setting it using the
EDL_WRITE_BD_ADDR_OPCODE command.
Presumably, this is the case for all non-ROME devices which all use the
EDL_WRITE_BD_ADDR_OPCODE command for this (unlike the ROME devices which
use a different command and expect the address in little-endian order).
Reverse the little-endian address before setting it to make sure that
the address can be configured using tools like btmgmt or using the
'local-bd-address' devicetree property.
Note that this can potentially break systems with boot firmware which
has started relying on the broken behaviour and is incorrectly passing
the address via devicetree in big-endian order.
The only device affected by this should be the WCN3991 used in some
Chromebooks. As ChromeOS updates the kernel and devicetree in lockstep,
the new 'qcom,local-bd-address-broken' property can be used to determine
if the firmware is buggy so that the underlying driver bug can be fixed
without breaking backwards compatibility.
Set the HCI_QUIRK_BDADDR_PROPERTY_BROKEN quirk for such platforms so
that the address is reversed when parsing the address property.
Fixes: 5c0a1001c8 ("Bluetooth: hci_qca: Add helper to set device address")
Cc: stable@vger.kernel.org # 5.1
Cc: Balakrishna Godavarthi <quic_bgodavar@quicinc.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Nikita Travkin <nikita@trvn.ru> # sc7180
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Some Bluetooth controllers lack persistent storage for the device
address and instead one can be provided by the boot firmware using the
'local-bd-address' devicetree property.
The Bluetooth devicetree bindings clearly states that the address should
be specified in little-endian order, but due to a long-standing bug in
the Qualcomm driver which reversed the address some boot firmware has
been providing the address in big-endian order instead.
Add a new quirk that can be set on platforms with broken firmware and
use it to reverse the address when parsing the property so that the
underlying driver bug can be fixed.
Fixes: 5c0a1001c8 ("Bluetooth: hci_qca: Add helper to set device address")
Cc: stable@vger.kernel.org # 5.1
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Several Qualcomm Bluetooth controllers lack persistent storage for the
device address and instead one can be provided by the boot firmware
using the 'local-bd-address' devicetree property.
The Bluetooth bindings clearly states that the address should be
specified in little-endian order, but due to a long-standing bug in the
Qualcomm driver which reversed the address some boot firmware has been
providing the address in big-endian order instead.
The boot firmware in SC7180 Trogdor Chromebooks is known to be affected
so mark the 'local-bd-address' property as broken to maintain backwards
compatibility with older firmware when fixing the underlying driver bug.
Note that ChromeOS always updates the kernel and devicetree in lockstep
so that there is no need to handle backwards compatibility with older
devicetrees.
Fixes: 7ec3e67307 ("arm64: dts: qcom: sc7180-trogdor: add initial trogdor and lazor dt")
Cc: stable@vger.kernel.org # 5.10
Cc: Rob Clark <robdclark@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Several Qualcomm Bluetooth controllers lack persistent storage for the
device address and instead one can be provided by the boot firmware
using the 'local-bd-address' devicetree property.
The Bluetooth bindings clearly states that the address should be
specified in little-endian order, but due to a long-standing bug in the
Qualcomm driver which reversed the address some boot firmware has been
providing the address in big-endian order instead.
The only device out there that should be affected by this is the WCN3991
used in some Chromebooks.
Add a 'qcom,local-bd-address-broken' property which can be set on these
platforms to indicate that the boot firmware is using the wrong byte
order.
Note that ChromeOS always updates the kernel and devicetree in lockstep
so that there is no need to handle backwards compatibility with older
devicetrees.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This reverts commit 7dcd3e014a.
Qualcomm Bluetooth controllers like WCN6855 do not have persistent
storage for the Bluetooth address and must therefore start as
unconfigured to allow the user to set a valid address unless one has
been provided by the boot firmware in the devicetree.
A recent change snuck into v6.8-rc7 and incorrectly started marking the
default (non-unique) address as valid. This specifically also breaks the
Bluetooth setup for some user of the Lenovo ThinkPad X13s.
Note that this is the second time Qualcomm breaks the driver this way
and that this was fixed last year by commit 6945795bc8 ("Bluetooth:
fix use-bdaddr-property quirk"), which also has some further details.
Fixes: 7dcd3e014a ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Cc: stable@vger.kernel.org # 6.8
Cc: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Clayton Craft <clayton@craftyguy.net>
Tested-by: Clayton Craft <clayton@craftyguy.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The current implementation for loading coalesced KPU profiles has
a limitation. The "offset" field, which is used to locate profiles
within the profile is restricted to a u16.
This restricts the number of profiles that can be loaded. This patch
addresses this limitation by increasing the size of the "offset" field.
Fixes: 11c730bfbf ("octeontx2-af: support for coalescing KPU profiles")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart says:
====================
gro: various fixes related to UDP tunnels
We found issues when a UDP tunnel endpoint is in a different netns than
where UDP GRO happens. This kind of setup is actually quite diverse,
from having one leg of the tunnel on a remove host, to having a tunnel
between netns (eg. being bridged in another one or on the host). In our
case that UDP tunnel was geneve.
UDP tunnel packets should not be GROed at the UDP level. The fundamental
issue here is such packet can't be detected in a foolproof way: we can't
know by looking at a packet alone and the current logic of looking up
UDP sockets is fragile (socket could be in another netns, packet could
be modified in between, etc). Because there is no way to make the GRO
code to correctly handle those packets in all cases, this series aims at
two things: making the net stack to correctly behave (as in, no crash
and no invalid packet) when such thing happens, and in some cases to
prevent this "early GRO" from happening.
First three patches fix issues when an "UDP tunneled" packet is being
GROed too early by rx-udp-gro-forwarding or rx-gro-list.
Last patch is preventing locally generated UDP tunnel packets from being
GROed. This turns out to be more complex than this patch alone as it
relies on skb->encapsulation which is currently untrusty in some cases
(see iptunnel_handle_offloads); but that should fix things in practice
and is acceptable for a fix. Future work is required to improve things
(prevent all locally generated UDP tunnel packets from being GROed),
such as fixing the misuse of skb->encapsulation in drivers; but that
would be net-next material.
Thanks!
Antoine
Since v3:
- Fixed the udpgro_fwd selftest in patch 5 (Jakub Kicinski feedback).
- Improved commit message on patch 3 (Willem de Bruijn feeback).
Since v2:
- Fixed a build issue with IPv6=m in patch 1 (Jakub Kicinski
feedback).
- Fixed typo in patch 1 (Nikolay Aleksandrov feedback).
- Added Reviewed-by tag on patch 2 (Willem de Bruijn feeback).
- Added back conversion to CHECKSUM_UNNECESSARY but only from non
CHECKSUM_PARTIAL in patch 3 (Paolo Abeni & Willem de Bruijn
feeback).
- Reworded patch 3 commit msg.
Since v1:
- Fixed a build issue with IPv6 disabled in patch 1.
- Reworked commit log in patch 2 (Willem de Bruijn feedback).
- Added Reviewed-by tags on patches 1 & 4 (Willem de Bruijn feeback).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP tunnel packets can't be GRO in-between their endpoints as this
causes different issues. The UDP GRO fwd vxlan tests were relying on
this and their expectations have to be fixed.
We keep both vxlan tests and expected no GRO from happening. The vxlan
UDP GRO bench test was removed as it's not providing any valuable
information now.
Fixes: a062260a9d ("selftests: net: add UDP GRO forwarding self-tests")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO has a fundamental issue with UDP tunnel packets as it can't detect
those in a foolproof way and GRO could happen before they reach the
tunnel endpoint. Previous commits have fixed issues when UDP tunnel
packets come from a remote host, but if those packets are issued locally
they could run into checksum issues.
If the inner packet has a partial checksum the information will be lost
in the GRO logic, either in udp4/6_gro_complete or in
udp_gro_complete_segment and packets will have an invalid checksum when
leaving the host.
Prevent local UDP tunnel packets from ever being GROed at the outer UDP
level.
Due to skb->encapsulation being wrongly used in some drivers this is
actually only preventing UDP tunnel packets with a partial checksum to
be GROed (see iptunnel_handle_offloads) but those were also the packets
triggering issues so in practice this should be sufficient.
Fixes: 9fd1ff5d2a ("udp: Support UDP fraglist GRO/GSO.")
Fixes: 36707061d6 ("udp: allow forwarding of plain (non-fraglisted) UDP GRO packets")
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP GRO validates checksums and in udp4/6_gro_complete fraglist packets
are converted to CHECKSUM_UNNECESSARY to avoid later checks. However
this is an issue for CHECKSUM_PARTIAL packets as they can be looped in
an egress path and then their partial checksums are not fixed.
Different issues can be observed, from invalid checksum on packets to
traces like:
gen01: hw csum failure
skb len=3008 headroom=160 headlen=1376 tailroom=0
mac=(106,14) net=(120,40) trans=160
shinfo(txflags=0 nr_frags=0 gso(size=0 type=0 segs=0))
csum(0xffff232e ip_summed=2 complete_sw=0 valid=0 level=0)
hash(0x77e3d716 sw=1 l4=1) proto=0x86dd pkttype=0 iif=12
...
Fix this by only converting CHECKSUM_NONE packets to
CHECKSUM_UNNECESSARY by reusing __skb_incr_checksum_unnecessary. All
other checksum types are kept as-is, including CHECKSUM_COMPLETE as
fraglist packets being segmented back would have their skb->csum valid.
Fixes: 9fd1ff5d2a ("udp: Support UDP fraglist GRO/GSO.")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If packets are GROed with fraglist they might be segmented later on and
continue their journey in the stack. In skb_segment_list those skbs can
be reused as-is. This is an issue as their destructor was removed in
skb_gro_receive_list but not the reference to their socket, and then
they can't be orphaned. Fix this by also removing the reference to the
socket.
For example this could be observed,
kernel BUG at include/linux/skbuff.h:3131! (skb_orphan)
RIP: 0010:ip6_rcv_core+0x11bc/0x19a0
Call Trace:
ipv6_list_rcv+0x250/0x3f0
__netif_receive_skb_list_core+0x49d/0x8f0
netif_receive_skb_list_internal+0x634/0xd40
napi_complete_done+0x1d2/0x7d0
gro_cell_poll+0x118/0x1f0
A similar construction is found in skb_gro_receive, apply the same
change there.
Fixes: 5e10da5385 ("skbuff: allow 'slow_gro' for skb carring sock reference")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rx-udp-gro-forwarding is enabled UDP packets might be GROed when
being forwarded. If such packets might land in a tunnel this can cause
various issues and udp_gro_receive makes sure this isn't the case by
looking for a matching socket. This is performed in
udp4/6_gro_lookup_skb but only in the current netns. This is an issue
with tunneled packets when the endpoint is in another netns. In such
cases the packets will be GROed at the UDP level, which leads to various
issues later on. The same thing can happen with rx-gro-list.
We saw this with geneve packets being GROed at the UDP level. In such
case gso_size is set; later the packet goes through the geneve rx path,
the geneve header is pulled, the offset are adjusted and frag_list skbs
are not adjusted with regard to geneve. When those skbs hit
skb_fragment, it will misbehave. Different outcomes are possible
depending on what the GROed skbs look like; from corrupted packets to
kernel crashes.
One example is a BUG_ON[1] triggered in skb_segment while processing the
frag_list. Because gso_size is wrong (geneve header was pulled)
skb_segment thinks there is "geneve header size" of data in frag_list,
although it's in fact the next packet. The BUG_ON itself has nothing to
do with the issue. This is only one of the potential issues.
Looking up for a matching socket in udp_gro_receive is fragile: the
lookup could be extended to all netns (not speaking about performances)
but nothing prevents those packets from being modified in between and we
could still not find a matching socket. It's OK to keep the current
logic there as it should cover most cases but we also need to make sure
we handle tunnel packets being GROed too early.
This is done by extending the checks in udp_unexpected_gso: GSO packets
lacking the SKB_GSO_UDP_TUNNEL/_CSUM bits and landing in a tunnel must
be segmented.
[1] kernel BUG at net/core/skbuff.c:4408!
RIP: 0010:skb_segment+0xd2a/0xf70
__udp_gso_segment+0xaa/0x560
Fixes: 9fd1ff5d2a ("udp: Support UDP fraglist GRO/GSO.")
Fixes: 36707061d6 ("udp: allow forwarding of plain (non-fraglisted) UDP GRO packets")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up till now only single character ('A' or 'B') was used to provide
information of HSR slave network device status.
As it is also possible and valid, that Interlink network device may
be supported as well, the description must be more verbose. As a result
the full string description is now used.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-03-27 (e1000e)
This series contains updates to e1000e driver only.
Vitaly adds retry mechanism for some PHY operations to workaround MDI
error and moves SMBus configuration to avoid possible PHY loss.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
e1000e: move force SMBUS from enable ulp function to avoid PHY loss issue
e1000e: Workaround for sporadic MDI error on Meteor Lake systems
====================
Link: https://lore.kernel.org/r/20240327185517.2587564-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Notice that skb_mark_for_recycle() is introduced later than fixes tag in
commit 6a5bcd84e8 ("page_pool: Allow drivers to hint on SKB recycling").
It is believed that fixes tag were missing a call to page_pool_release_page()
between v5.9 to v5.14, after which is should have used skb_mark_for_recycle().
Since v6.6 the call page_pool_release_page() were removed (in
commit 535b9c61bd ("net: page_pool: hide page_pool_release_page()")
and remaining callers converted (in commit 6bfef2ec01 ("Merge branch
'net-page_pool-remove-page_pool_release_page'")).
This leak became visible in v6.8 via commit dba1b8a7ab ("mm/page_pool: catch
page_pool memory leaks").
Cc: stable@vger.kernel.org
Fixes: 6c5aa6fc4d ("xen networking: add basic XDP support for xen-netfront")
Reported-by: Leonidas Spyropoulos <artafinde@archlinux.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218654
Reported-by: Arthur Borsboom <arthurborsboom@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/171154167446.2671062.9127105384591237363.stgit@firesoul
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provide devlink documentation for three eswitch attributes:
mode, inline-mode, and encap-mode.
Signed-off-by: William Tu <witu@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20240325181228.6244-1-witu@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current release - regressions:
- ipv6: fix address dump when IPv6 is disabled on an interface
Current release - new code bugs:
- bpf: temporarily disable atomic operations in BPF arena
- nexthop: fix uninitialized variable in nla_put_nh_group_stats()
Previous releases - regressions:
- bpf: protect against int overflow for stack access size
- hsr: fix the promiscuous mode in offload mode
- wifi: don't always use FW dump trig
- tls: adjust recv return with async crypto and failed copy to userspace
- tcp: properly terminate timers for kernel sockets
- ice: fix memory corruption bug with suspend and rebuild
- at803x: fix kernel panic with at8031_probe
- qeth: handle deferred cc1
Previous releases - always broken:
- bpf: fix bug in BPF_LDX_MEMSX
- netfilter: reject table flag and netdev basechain updates
- inet_defrag: prevent sk release while still in use
- wifi: pick the version of SESSION_PROTECTION_NOTIF
- wwan: t7xx: split 64bit accesses to fix alignment issues
- mlxbf_gige: call request_irq() after NAPI initialized
- hns3: fix kernel crash when devlink reload during pf initialization
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=HbtI
-----END PGP SIGNATURE-----
Merge tag 'net-6.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from bpf, WiFi and netfilter.
Current release - regressions:
- ipv6: fix address dump when IPv6 is disabled on an interface
Current release - new code bugs:
- bpf: temporarily disable atomic operations in BPF arena
- nexthop: fix uninitialized variable in nla_put_nh_group_stats()
Previous releases - regressions:
- bpf: protect against int overflow for stack access size
- hsr: fix the promiscuous mode in offload mode
- wifi: don't always use FW dump trig
- tls: adjust recv return with async crypto and failed copy to
userspace
- tcp: properly terminate timers for kernel sockets
- ice: fix memory corruption bug with suspend and rebuild
- at803x: fix kernel panic with at8031_probe
- qeth: handle deferred cc1
Previous releases - always broken:
- bpf: fix bug in BPF_LDX_MEMSX
- netfilter: reject table flag and netdev basechain updates
- inet_defrag: prevent sk release while still in use
- wifi: pick the version of SESSION_PROTECTION_NOTIF
- wwan: t7xx: split 64bit accesses to fix alignment issues
- mlxbf_gige: call request_irq() after NAPI initialized
- hns3: fix kernel crash when devlink reload during pf
initialization"
* tag 'net-6.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (81 commits)
inet: inet_defrag: prevent sk release while still in use
Octeontx2-af: fix pause frame configuration in GMP mode
net: lan743x: Add set RFE read fifo threshold for PCI1x1x chips
net: bcmasp: Remove phy_{suspend/resume}
net: bcmasp: Bring up unimac after PHY link up
net: phy: qcom: at803x: fix kernel panic with at8031_probe
netfilter: arptables: Select NETFILTER_FAMILY_ARP when building arp_tables.c
netfilter: nf_tables: skip netdev hook unregistration if table is dormant
netfilter: nf_tables: reject table flag and netdev basechain updates
netfilter: nf_tables: reject destroy command to remove basechain hooks
bpf: update BPF LSM designated reviewer list
bpf: Protect against int overflow for stack access size
bpf: Check bloom filter map value size
bpf: fix warning for crash_kexec
selftests: netdevsim: set test timeout to 10 minutes
net: wan: framer: Add missing static inline qualifiers
mlxbf_gige: call request_irq() after NAPI initialized
tls: get psock ref after taking rxlock to avoid leak
selftests: tls: add test with a partially invalid iov
tls: adjust recv return with async crypto and failed copy to userspace
...
ip_local_out() and other functions can pass skb->sk as function argument.
If the skb is a fragment and reassembly happens before such function call
returns, the sk must not be released.
This affects skb fragments reassembled via netfilter or similar
modules, e.g. openvswitch or ct_act.c, when run as part of tx pipeline.
Eric Dumazet made an initial analysis of this bug. Quoting Eric:
Calling ip_defrag() in output path is also implying skb_orphan(),
which is buggy because output path relies on sk not disappearing.
A relevant old patch about the issue was :
8282f27449 ("inet: frag: Always orphan skbs inside ip_defrag()")
[..]
net/ipv4/ip_output.c depends on skb->sk being set, and probably to an
inet socket, not an arbitrary one.
If we orphan the packet in ipvlan, then downstream things like FQ
packet scheduler will not work properly.
We need to change ip_defrag() to only use skb_orphan() when really
needed, ie whenever frag_list is going to be used.
Eric suggested to stash sk in fragment queue and made an initial patch.
However there is a problem with this:
If skb is refragmented again right after, ip_do_fragment() will copy
head->sk to the new fragments, and sets up destructor to sock_wfree.
IOW, we have no choice but to fix up sk_wmem accouting to reflect the
fully reassembled skb, else wmem will underflow.
This change moves the orphan down into the core, to last possible moment.
As ip_defrag_offset is aliased with sk_buff->sk member, we must move the
offset into the FRAG_CB, else skb->sk gets clobbered.
This allows to delay the orphaning long enough to learn if the skb has
to be queued or if the skb is completing the reasm queue.
In the former case, things work as before, skb is orphaned. This is
safe because skb gets queued/stolen and won't continue past reasm engine.
In the latter case, we will steal the skb->sk reference, reattach it to
the head skb, and fix up wmem accouting when inet_frag inflates truesize.
Fixes: 7026b1ddb6 ("netfilter: Pass socket pointer down through okfn().")
Diagnosed-by: Eric Dumazet <edumazet@google.com>
Reported-by: xingwei lee <xrivendell7@gmail.com>
Reported-by: yue sun <samsun1006219@gmail.com>
Reported-by: syzbot+e5167d7144a62715044c@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240326101845.30836-1-fw@strlen.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The Octeontx2 MAC block (CGX) has separate data paths (SMU and GMP) for
different speeds, allowing for efficient data transfer.
The previous patch which added pause frame configuration has a bug due
to which pause frame feature is not working in GMP mode.
This patch fixes the issue by configurating appropriate registers.
Fixes: f7e086e754 ("octeontx2-af: Pause frame configuration at cgx")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240326052720.4441-1-hkelam@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
PCI11x1x Rev B0 devices might drop packets when receiving back to back frames
at 2.5G link speed. Change the B0 Rev device's Receive filtering Engine FIFO
threshold parameter from its hardware default of 4 to 3 dwords to prevent the
problem. Rev C0 and later hardware already defaults to 3 dwords.
Fixes: bb4f6bffe3 ("net: lan743x: Add PCI11010 / PCI11414 device IDs")
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240326065805.686128-1-Raju.Lakkaraju@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Duoming Zhou