In preparation for turning this into a common loader for 32-bit and 64-bit
platforms, ensure the code will compile cleanly for either.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Add a generic GRUB_PE32_MAGIC definition for the PE 'MZ' tag and delete
the existing one in arm64/linux.h.
Update arm64 Linux loader to use this new definition.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
There is nothing ARM64 (or even ARM) specific about the efi fdt helper
library, which is used for locating or overriding a firmware-provided
devicetree in a UEFI system - so move it to loader/efi for reuse.
Move the fdtload.h include file to grub/efi and update path to
efi/fdtload.h in source code referring to it.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
grub_efi_allocate_pages Essentially does 2 unrelated things:
* Allocate at fixed address.
* Allocate at any address.
To switch between 2 different functions it uses address == 0 as magic
value which is wrong as 0 is a perfectly valid fixed adress to allocate at.
Expose a new function, grub_efi_allocate_pages_real(), making it possible
to specify allocation type and memory type as supported by the UEFI
AllocatePages boot service.
Make grub_efi_allocate_pages() a consumer of the new function,
maintaining its old functionality.
Also delete some left-around #if 1/#else blocks in the affected
functions.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Use same algorithm as in libblkid from util-linux v2.30.
1. Take first 16 bytes from UTF-8 encoded string of VolumeSetIdentifier
2. If all bytes are hexadecimal digits, convert to lowercase and use as UUID
3. If first 8 bytes are not all hexadecimal digits, convert those 8 bytes
to their hexadecimal representation, resulting in 16 bytes for UUID
4. Otherwise, compose UUID from two parts:
1. part: converted first 8 bytes (which are hexadecimal digits) to lowercase
2. part: encoded following 4 bytes to their hexadecimal representation (16 bytes)
So UUID would always have 16 hexadecimal digits in lowercase variant.
According to UDF specification, first 16 Unicode characters of
VolumeSetIdentifier should be unique value and first 8 should be
hexadecimal characters.
In most cases all 16 characters are hexadecimal, but e.g. MS Windows
format.exe set only first 8 as hexadecimal and remaining as fixed
(non-unique) which violates specification.
UDF dstring has stored length in the last byte of buffer. Therefore last
byte is not part of recorded characters. And empty string in dstring is
encoded as empty buffer, including first byte (compression id).
when protocols_per_handle returns error, we can't use the pointers we
passed to it, and that includes trusting num_protocols.
Signed-off-by: Peter Jones <pjones@redhat.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
On such a filesystem, inodes may have EXT4_ENCRYPT_FLAG set.
For a regular file, this means its contents are encrypted; for a
directory, this means the filenames in its directory entries are
encrypted; and for a symlink, this means its target is encrypted. Since
GRUB cannot decrypt encrypted contents or filenames, just issue an error
if it would need to do so. This is sufficient to allow unencrypted boot
files to co-exist with encrypted files elsewhere on the filesystem.
(Note that encrypted regular files and symlinks will not normally be
encountered outside an encrypted directory; however, it's possible via
hard links, so they still need to be handled.)
Tested by booting from an ext4 /boot partition on which I had run
'tune2fs -O encrypt'. I also verified that the expected error messages
are printed when trying to access encrypted directories, files, and
symlinks from the GRUB command line. Also ran 'sudo ./grub-fs-tester
ext4_encrypt'; note that this requires e2fsprogs v1.43+ and Linux v4.1+.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Don't use devspec to determine the OBP path on SPARC hardware. Within all
versions of Linux on SPARC, the devspec returns one of three values:
"none", "vnet-port", or "vdisk". Unlike on PPC, none of these values
are useful in determining the OBP path.
Before this patch grub-ofpathname always returned the wrong value
for a virtual disk. For example:
% grub-ofpathname /dev/vdiskc2
vdisk/disk@2:b
After this patch it now returns the correct value:
% grub-ofpathname /dev/vdiskc2
/virtual-devices@100/channel-devices@200/disk@2:b
Orabug: 24459765
Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
This patch adds "--nounzip" option support in order to
be compatible with the module command of multiboot on other architecture,
by this way we can simplify grub-mkconfig support code.
This patch also allow us to use zip compressed module(like Linux kernel
for Dom0).
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Xen is currently crashing because of malformed compatible property for
the boot module. This is because the property string is not
null-terminated as requested by the ePAR spec.
Signed-off-by: Julien Grall <julien.grall@linaro.org>
Tested-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
The ihandle is left open with a cd-core image. This will cause a delay
booting grub from a virtual cdrom in a LDOM. It will also cause problems
as Linux boots, since it expects the ihandle to be closed during init.
Orabug: 25911275
Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
This patch adds support for virtual LAN (VLAN) tagging. VLAN tagging allows
multiple VLANs in a bridged network to share the same physical network link
but maintain isolation:
http://en.wikipedia.org/wiki/IEEE_802.1Q
* grub-core/net/ethernet.c: Add check, get, and set vlan tag id.
* grub-core/net/drivers/ieee1275/ofnet.c: Get vlan tag id from bootargs.
* grub-core/net/arp.c: Add check.
* grub-core/net/ip.c: Likewise.
* include/grub/net/arp.h: Add vlantag attribute.
* include/grub/net/ip.h: Likewise.
