Check the error bits in the interrupt status register. According to the
AHCI 1.2 spec, "Interrupt sources that are disabled (‘0’) are still
reflected in the status registers.", so this should work even though
grub uses polling
This fixes the following problem on a Fujitsu E744 laptop:
Sometimes there is a very long delay (up to several minutes) when
booting from hard disk. It seems accessing the DVD drive (which has no
disk inserted) sometimes fails with some errors, which leads to each
access being stalled until the 20s timeout triggers. This seems to
happen when grub is trying to read filesystem/partition data.
The problem is that the command_issue bit that is checked in the loop is
only reset if the "HBA receives a FIS which clears the BSY, DRQ, and ERR
bits for the command", but the ERR bit is never cleared. Therefore
command_issue is never reset and grub waits for the timeout.
The relevant bit in our case is the Task File Error Status (TFES), which
is equivalent to the ERR bit 0 in tfd. But this patch also checks
the other error bits except for the "Interface non-fatal error status"
bit.
Signed-off-by: Stefan Fritsch <fritsch@genua.de>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
The properties #address-cells and #size-cells are used to know the
number of cells for ranges provided by "regs". If they don't exist, the
value are resp. 2 and 1.
Currently, when multiboot nodes are created it is assumed that #address-cells
and #size-cells are exactly 2. However, they are never set by GRUB and
will result to later failure when the device-tree is generated by GRUB
or contain different values.
To prevent this failure, create the both properties in the chosen nodes.
Signed-off-by: Julien Grall <julien.grall@linaro.org>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Prevent a double open. This can cause problems with some ieee1275
devices, causing the system to hang. The double open can occur
as follows:
grub_ls_list_files (char *dirname, int longlist, int all, int human)
dev = grub_device_open (device_name);
dev remains open while:
grub_normal_print_device_info (device_name);
dev = grub_device_open (name);
Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com>
Signed-off-by: Daniel Kiper <daniel.kiper@oracle.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
On efi systems, make pmtimer based tsc calibration the default over the
pit. This prevents Grub from hanging on Intel SoC systems that power gate
the pit.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
When we exit grub, we don't free all the memory that we allocated earlier
for our heap region. This can cause problems with setups where you try
to descend the boot order using "exit" entries, such as PXE -> HD boot
scenarios.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
The reboot function calls machine_fini() and then reboots the system.
Currently it lives in lib/ which means it gets compiled into the
reboot module which lives on the heap.
In a following patch, I want to free the heap on machine_fini()
though, so we would free the memory that the code is running in. That
obviously breaks with smarter UEFI implementations.
So this patch moves it into the core. That way we ensure that all
code running after machine_fini() in the UEFI case is running from
memory that got allocated (and gets deallocated) by the UEFI core.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
The `grub_util_exec_redirect_all` helper function can be used to
spawn an executable and redirect its output to some files. After calling
`fork()`, the parent will wait for the child to terminate with
`waitpid()` while the child prepares its file descriptors, environment
and finally calls `execvp()`. If something in the children's setup
fails, it will stop by calling `exit(127)`.
Calling `exit()` will cause any function registered via `atexit()` to be
executed, which is usually the wrong thing to do in a child. And
actually, one can easily observe faulty behaviour on musl-based systems
without modprobe(8) installed: executing `grub-install --help` will call
`grub_util_exec_redirect_all` with "modprobe", which obviously fails if
modprobe(8) is not installed. Due to the child now exiting and invoking
the `atexit()` handlers, it will clean up some data structures of the
parent and cause it to be deadlocked in the `waitpid()` syscall.
The issue can easily be fixed by calling `_exit(127)` instead, which is
especially designed to be called when the atexit-handlers should not be
executed.
Signed-off-by: Patrick Steinhardt <ps@pks.im>
Previously we had multiboot and multiboot2 declaring the same symbols.
This can potentially lead to aliasing and strange behaviours when e.g.
module instead of module2 is used with multiboot2.
Bug: #51137
With upcoming changes to EDK2, allocations of type EFI_LOADER_DATA may
not return regions with execute ability. Since modules are loaded onto
the heap, change the heap allocation type to GRUB_EFI_LOADER_CODE in
order to permit execution on systems with this feature enabled.
Closes: 50420
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
In preparation for turning this into a common loader for 32-bit and 64-bit
platforms, ensure the code will compile cleanly for either.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Add a generic GRUB_PE32_MAGIC definition for the PE 'MZ' tag and delete
the existing one in arm64/linux.h.
Update arm64 Linux loader to use this new definition.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
There is nothing ARM64 (or even ARM) specific about the efi fdt helper
library, which is used for locating or overriding a firmware-provided
devicetree in a UEFI system - so move it to loader/efi for reuse.
Move the fdtload.h include file to grub/efi and update path to
efi/fdtload.h in source code referring to it.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
grub_efi_allocate_pages Essentially does 2 unrelated things:
* Allocate at fixed address.
* Allocate at any address.
To switch between 2 different functions it uses address == 0 as magic
value which is wrong as 0 is a perfectly valid fixed adress to allocate at.
Expose a new function, grub_efi_allocate_pages_real(), making it possible
to specify allocation type and memory type as supported by the UEFI
AllocatePages boot service.
Make grub_efi_allocate_pages() a consumer of the new function,
maintaining its old functionality.
Also delete some left-around #if 1/#else blocks in the affected
functions.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Use same algorithm as in libblkid from util-linux v2.30.
1. Take first 16 bytes from UTF-8 encoded string of VolumeSetIdentifier
2. If all bytes are hexadecimal digits, convert to lowercase and use as UUID
3. If first 8 bytes are not all hexadecimal digits, convert those 8 bytes
to their hexadecimal representation, resulting in 16 bytes for UUID
4. Otherwise, compose UUID from two parts:
1. part: converted first 8 bytes (which are hexadecimal digits) to lowercase
2. part: encoded following 4 bytes to their hexadecimal representation (16 bytes)
So UUID would always have 16 hexadecimal digits in lowercase variant.
According to UDF specification, first 16 Unicode characters of
VolumeSetIdentifier should be unique value and first 8 should be
hexadecimal characters.
In most cases all 16 characters are hexadecimal, but e.g. MS Windows
format.exe set only first 8 as hexadecimal and remaining as fixed
(non-unique) which violates specification.
UDF dstring has stored length in the last byte of buffer. Therefore last
byte is not part of recorded characters. And empty string in dstring is
encoded as empty buffer, including first byte (compression id).
when protocols_per_handle returns error, we can't use the pointers we
passed to it, and that includes trusting num_protocols.
Signed-off-by: Peter Jones <pjones@redhat.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
On such a filesystem, inodes may have EXT4_ENCRYPT_FLAG set.
For a regular file, this means its contents are encrypted; for a
directory, this means the filenames in its directory entries are
encrypted; and for a symlink, this means its target is encrypted. Since
GRUB cannot decrypt encrypted contents or filenames, just issue an error
if it would need to do so. This is sufficient to allow unencrypted boot
files to co-exist with encrypted files elsewhere on the filesystem.
(Note that encrypted regular files and symlinks will not normally be
encountered outside an encrypted directory; however, it's possible via
hard links, so they still need to be handled.)
Tested by booting from an ext4 /boot partition on which I had run
'tune2fs -O encrypt'. I also verified that the expected error messages
are printed when trying to access encrypted directories, files, and
symlinks from the GRUB command line. Also ran 'sudo ./grub-fs-tester
ext4_encrypt'; note that this requires e2fsprogs v1.43+ and Linux v4.1+.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Don't use devspec to determine the OBP path on SPARC hardware. Within all
versions of Linux on SPARC, the devspec returns one of three values:
"none", "vnet-port", or "vdisk". Unlike on PPC, none of these values
are useful in determining the OBP path.
Before this patch grub-ofpathname always returned the wrong value
for a virtual disk. For example:
% grub-ofpathname /dev/vdiskc2
vdisk/disk@2:b
After this patch it now returns the correct value:
% grub-ofpathname /dev/vdiskc2
/virtual-devices@100/channel-devices@200/disk@2:b
Orabug: 24459765
Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
This patch adds "--nounzip" option support in order to
be compatible with the module command of multiboot on other architecture,
by this way we can simplify grub-mkconfig support code.
This patch also allow us to use zip compressed module(like Linux kernel
for Dom0).
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Xen is currently crashing because of malformed compatible property for
the boot module. This is because the property string is not
null-terminated as requested by the ePAR spec.
Signed-off-by: Julien Grall <julien.grall@linaro.org>
Tested-by: Fu Wei <fu.wei@linaro.org>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
The ihandle is left open with a cd-core image. This will cause a delay
booting grub from a virtual cdrom in a LDOM. It will also cause problems
as Linux boots, since it expects the ihandle to be closed during init.
Orabug: 25911275
Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
This patch adds support for virtual LAN (VLAN) tagging. VLAN tagging allows
multiple VLANs in a bridged network to share the same physical network link
but maintain isolation:
http://en.wikipedia.org/wiki/IEEE_802.1Q
* grub-core/net/ethernet.c: Add check, get, and set vlan tag id.
* grub-core/net/drivers/ieee1275/ofnet.c: Get vlan tag id from bootargs.
* grub-core/net/arp.c: Add check.
* grub-core/net/ip.c: Likewise.
* include/grub/net/arp.h: Add vlantag attribute.
* include/grub/net/ip.h: Likewise.
In util/getroot and efidisk slightly modify exitsing comment to mostly
retain it but still make GCC7 compliant with respect to fall through
annotation.
In grub-core/lib/xzembed/xz_dec_lzma2.c it adds same comments as
upstream.
In grub-core/tests/setjmp_tets.c declare functions as "noreturn" to
suppress GCC7 warning.
In grub-core/gnulib/regexec.c use new __attribute__, because existing
annotation is not recognized by GCC7 parser (which requires that comment
immediately precedes case statement).
Otherwise add FALLTHROUGH comment.
Closes: 50598
Fixed loading of ACPI tables on EFI (side effect was apparent memory
corruption ranging from unpredictable behavior to system reset).
Reported by Nando Eva <nando4eva@ymail.com>
iPXE adds Simple File System Protocol to loaded image handle, as side
effect it also adds Block IO protocol (according to comments, to work
around some bugs in EDK2). GRUB assumes that every device with Block IO
is disk and skips network initialization entirely. But iPXE Block IO
implementation is just a stub which always fails for every operation
so cannot be used. Attempt to detect and skip such devices.
We are using media ID which iPXE sets to "iPXE" and block IO size in
hope that no real device would announce 1B block ...
Closes: 50518
UEFI 2.6 9.3.6.4 File Path Media Device Path says that Path Name is
"A NULL-terminated Path string including directory and file names".
Strip final NULL from Path Name in each File Path node when constructing
full path. To be on safe side, strip all of them.
Fixes failure chainloading grub from grub, when loaded grub truncates
image path and does not find its grub.cfg.
https://bugzilla.opensuse.org/show_bug.cgi?id=1026344
This was triggered by commit ce95549cc54b5d6f494608a7c390dba3aab4fba7;
before it we built Path Name without trailing NULL, and apparently all
other bootloaders use single File Path node, thus not exposing this bug.
1. Do not assume block list and fragment are mutually exclusive. Squash
can pack file tail as fragment (unless -no-fragments is specified); so
check read offset and read either from block list or from fragments as
appropriate.
2. Support sparse files with zero blocks.
3. Fix fragment read - frag.offset is absolute fragment position,
not offset relative to ino.chunk.
Reported and tested by Carlo Caione <carlo@endlessm.com>
In case of GRUB we put remapper after domain pages and not at 0x0.
In this case we use max_addr to put remapper. Unfortunately we increment
max_addr as well in this case resulting in virt mapping mapping page
at old max_addr and trying to boot using new max_addr.
Closes 46014.
Unified Extensible Firmware Interface Specification, Version 2.6,
section 2.3.4, x64 Platforms, boot services, says among others:
The stack must be 16-byte aligned. So, do it. Otherwise OS may
boot only by chance as it happens right now.
Signed-off-by: Daniel Kiper <daniel.kiper@oracle.com>
According to EABI only STT_FUNC has convention of lowest bit indicating
execution mode. R_THM_{JUMP,CALL}* relocations are assumed to be pointing
to thumb mode unless they use STT_FUNC.
If ascent is bigger than height - 2, then we draw over character box but then
to clear cursor we only draw over character box. So trim ascent if necessarry.
