IEEE 1275-1994 Standard for Boot (Initialization Configuration)
Firmware: Core Requirements and Practices
E.3.2.2 Bus-specific methods for bus nodes
A package implementing the scsi-2 device type shall implement the
following bus-specific method:
no-data-command ( cmd-addr -- error? )
Executes a simple SCSI command, automatically retrying under
certain conditions. cmd-addr is the address of a 6-byte command buffer
containing an SCSI command that does not have a data transfer phase.
Executes the command, retrying indefinitely with the same retry criteria
as retry-command.
error? is nonzero if an error occurred, zero otherwise.
NOTE no-data-command is a convenience function. It provides
no capabilities that are not present in retry-command, but for
those commands that meet its restrictions, it is easier to use.
Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
IEEE 1275-1994 Standard for Boot (Initialization Configuration)
Firmware: Core Requirements and Practices
E.3.2.2 Bus-specific methods for bus nodes
A package implementing the scsi-2 device type shall implement the
following bus-specific method:
set-address ( unit# target# -- )
Sets the SCSI target number (0x0..0xf) and unit number (0..7) to which
subsequent commands apply.
This function is for devices with #address-cells == 2
Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Convert physical address to text unit-string.
Convert phys.lo ... phys-high, the numerical representation, to unit-string,
the text string representation of a physical address within the address
space defined by this device node. The number of cells in the list
phys.lo ... phys.hi is determined by the value of the #address-cells property
of this node.
This function is for devices with #address-cells == 4
Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
decode-unit ( addr len -- phys.lo ... phys.hi )
Convert text unit-string to physical address.
Convert unit-string, the text string representation, to phys.lo ... phys.hi,
the numerical representation of a physical address within the address space
defined by this device node. The number of cells in the list
phys.lo ... phys.hi is determined by the value of the #address-cells
property of this node.
This function is for devices with #address-cells == 4
Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
grub_aout_load() has a grub_file_t parameter, and depending on what order
includes land in, it's sometimes not defined. This patch explicitly adds
file.h to aout.h so that it will always be defined.
Signed-off-by: Peter Jones <pjones@redhat.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
<grub/machine/loader.h> (for machine arm/efi) and
<grub/machine/kernel.h> (for machine arm/coreboot) will not always
resolve (and will likely not be valid to) if pulled in when building
non-native commands, such as host tools or the "file" command.
So explicitly include them with their expanded pathnames.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Use kernel header struct and magic definition to align (and coexist) with
i386/arm64 ports.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Rename GRUB_LINUX_MAGIC_SIGNATURE GRUB_LINUX_I386_MAGIC_SIGNATURE,
to be usable in code that supports more than one image type.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Replace uses of GRUB_LINUX_MACHINE_HEADER and GRUB_LINUX_CPU_HEADER
with GRUB_<arch>_LINUX_HEADER include guards to prevent issues when
including more than one of them.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
The EFI page definitions and macros are generic and should not be confined
to arm64 headers - so move to efi/memory.h.
Also add EFI_PAGE_SIZE macro.
Update loader sources to reflect new header location.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
The definition of bpb's num_total_sectors_16 and num_total_sectors_32
is that either the 16-bit field is non-zero and is used (in which case
eg mkfs.fat sets the 32-bit field to zero), or it is zero and the
32-bit field is used. Therefore, a BPB is invalid only if *both*
fields are zero; having one field as zero and the other as non-zero is
the case to be expected. (Indeed, according to Microsoft's specification
one of the fields *must* be zero, and the other non-zero.)
This affects all users of grub_chainloader_patch_bpb which are in
chainloader.c, freedos.c, and ntldr.c
Some descriptions of the semantics of these two fields:
https://www.win.tue.nl/~aeb/linux/fs/fat/fat-1.html
The old 2-byte fields "total number of sectors" and "number of
sectors per FAT" are now zero; this information is now found in
the new 4-byte fields.
(Here given in the FAT32 EBPB section but the total sectors 16/32 bit
fields semantic is true of FAT12 and FAT16 too.)
https://wiki.osdev.org/FAT#BPB_.28BIOS_Parameter_Block.29
19 | 2 | The total sectors in the logical volume. If this value is 0,
it means there are more than 65535 sectors in the volume, and the actual
count is stored in "Large Sectors (bytes 32-35).
32 | 4 | Large amount of sector on media. This field is set if there
are more than 65535 sectors in the volume.
(Doesn't specify what the "large" field is set to when unused, but as
mentioned mkfs.fat sets it to zero then.)
https://technet.microsoft.com/en-us/library/cc976796.aspx
0x13 | WORD | 0x0000 |
Small Sectors . The number of sectors on the volume represented in 16
bits (< 65,536). For volumes larger than 65,536 sectors, this field
has a value of zero and the Large Sectors field is used instead.
0x20 | DWORD | 0x01F03E00 |
Large Sectors . If the value of the Small Sectors field is zero, this
field contains the total number of sectors in the FAT16 volume. If the
value of the Small Sectors field is not zero, the value of this field
is zero.
https://staff.washington.edu/dittrich/misc/fatgen103.pdf page 10
BPB_TotSec16 | 19 | 2 |
This field is the old 16-bit total count of sectors on the volume.
This count includes the count of all sectors in all four regions of the
volume. This field can be 0; if it is 0, then BPB_TotSec32 must be
non-zero. For FAT32 volumes, this field must be 0. For FAT12 and
FAT16 volumes, this field contains the sector count, and
BPB_TotSec32 is 0 if the total sector count “fits” (is less than
0x10000).
BPB_TotSec32 | 32 | 4 |
This field is the new 32-bit total count of sectors on the volume.
This count includes the count of all sectors in all four regions of the
volume. This field can be 0; if it is 0, then BPB_TotSec16 must be
non-zero. For FAT32 volumes, this field must be non-zero. For
FAT12/FAT16 volumes, this field contains the sector count if
BPB_TotSec16 is 0 (count is greater than or equal to 0x10000).
(This specifies that an unused BPB_TotSec32 field is set to zero.)
By the way fix offsets in include/grub/fat.h.
Tested with lDebug booted in qemu via grub2's
FreeDOS direct loading support, refer to
https://bitbucket.org/ecm/ldosboot + https://bitbucket.org/ecm/ldebug
Signed-off-by: C. Masloch <pushbx@38.de>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Code is currently ignoring errors from efibootmgr, giving users
clearly bogus output like:
Setting up grub-efi-amd64 (2.02~beta3-4) ...
Installing for x86_64-efi platform.
Could not delete variable: No space left on device
Could not prepare Boot variable: No space left on device
Installation finished. No error reported.
and then potentially unbootable systems. If efibootmgr fails, grub-install
should know that and report it!
We've been using similar patch in Debian now for some time, with no ill effects.
Signed-off-by: Steve McIntyre <93sam@debian.org>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
When we exit grub, we don't free all the memory that we allocated earlier
for our heap region. This can cause problems with setups where you try
to descend the boot order using "exit" entries, such as PXE -> HD boot
scenarios.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
The reboot function calls machine_fini() and then reboots the system.
Currently it lives in lib/ which means it gets compiled into the
reboot module which lives on the heap.
In a following patch, I want to free the heap on machine_fini()
though, so we would free the memory that the code is running in. That
obviously breaks with smarter UEFI implementations.
So this patch moves it into the core. That way we ensure that all
code running after machine_fini() in the UEFI case is running from
memory that got allocated (and gets deallocated) by the UEFI core.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Previously we had multiboot and multiboot2 declaring the same symbols.
This can potentially lead to aliasing and strange behaviours when e.g.
module instead of module2 is used with multiboot2.
Bug: #51137
Add a generic GRUB_PE32_MAGIC definition for the PE 'MZ' tag and delete
the existing one in arm64/linux.h.
Update arm64 Linux loader to use this new definition.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
There is nothing ARM64 (or even ARM) specific about the efi fdt helper
library, which is used for locating or overriding a firmware-provided
devicetree in a UEFI system - so move it to loader/efi for reuse.
Move the fdtload.h include file to grub/efi and update path to
efi/fdtload.h in source code referring to it.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
grub_efi_allocate_pages Essentially does 2 unrelated things:
* Allocate at fixed address.
* Allocate at any address.
To switch between 2 different functions it uses address == 0 as magic
value which is wrong as 0 is a perfectly valid fixed adress to allocate at.
Expose a new function, grub_efi_allocate_pages_real(), making it possible
to specify allocation type and memory type as supported by the UEFI
AllocatePages boot service.
Make grub_efi_allocate_pages() a consumer of the new function,
maintaining its old functionality.
Also delete some left-around #if 1/#else blocks in the affected
functions.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
This patch adds support for virtual LAN (VLAN) tagging. VLAN tagging allows
multiple VLANs in a bridged network to share the same physical network link
but maintain isolation:
http://en.wikipedia.org/wiki/IEEE_802.1Q
* grub-core/net/ethernet.c: Add check, get, and set vlan tag id.
* grub-core/net/drivers/ieee1275/ofnet.c: Get vlan tag id from bootargs.
* grub-core/net/arp.c: Add check.
* grub-core/net/ip.c: Likewise.
* include/grub/net/arp.h: Add vlantag attribute.
* include/grub/net/ip.h: Likewise.
We only support FDT files with EFI on arm and arm64 systems, not
on x86. So move the helper that finds a prepopulated FDT UUID
into its own file and only build it for architectures where it
also gets called.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
If EFI is nice enough to pass us an FDT using configuration tables on 32bit
ARM, we should really try and make use of it.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Searching for a device tree that EFI passes to us via configuration tables
is nothing architecture specific. Move it into generic code.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
