Return the number of blocks of storage associated with the device or
instance. Where a "block" is a unit of storage consisting of the number
of bytes returned by the package's "block-size" method. If the size cannot
be determined, the #blocks method returns the maximum unsigned integer
(which, because of Open Firmware's assumption of two's complement arithmetic,
is equivalent to the signed number -1). If the number of blocks exceeds
the range of an unsigned number, return 0 to alert the caller to try
the #blocks64 command.
Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
IEEE Std 1275-1994 Standard for Boot (Initialization Configuration)
Firmware: Core Requirements and Practices
3.8.3 deblocker support package
Any package that uses the "deblocker" support package must define
the following method, which the deblocker uses as a low-level
interface to the device
block-size ( -- block-len ) Return "granularity" for accesses to this
device.
Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
IEEE 1275-1994 Standard for Boot (Initialization Configuration)
Firmware: Core Requirements and Practices
E.3.2.2 Bus-specific methods for bus nodes
A package implementing the scsi-2 device type shall implement the
following bus-specific method:
no-data-command ( cmd-addr -- error? )
Executes a simple SCSI command, automatically retrying under
certain conditions. cmd-addr is the address of a 6-byte command buffer
containing an SCSI command that does not have a data transfer phase.
Executes the command, retrying indefinitely with the same retry criteria
as retry-command.
error? is nonzero if an error occurred, zero otherwise.
NOTE no-data-command is a convenience function. It provides
no capabilities that are not present in retry-command, but for
those commands that meet its restrictions, it is easier to use.
Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
IEEE 1275-1994 Standard for Boot (Initialization Configuration)
Firmware: Core Requirements and Practices
E.3.2.2 Bus-specific methods for bus nodes
A package implementing the scsi-2 device type shall implement the
following bus-specific method:
set-address ( unit# target# -- )
Sets the SCSI target number (0x0..0xf) and unit number (0..7) to which
subsequent commands apply.
This function is for devices with #address-cells == 2
Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Convert physical address to text unit-string.
Convert phys.lo ... phys-high, the numerical representation, to unit-string,
the text string representation of a physical address within the address
space defined by this device node. The number of cells in the list
phys.lo ... phys.hi is determined by the value of the #address-cells property
of this node.
This function is for devices with #address-cells == 4
Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
decode-unit ( addr len -- phys.lo ... phys.hi )
Convert text unit-string to physical address.
Convert unit-string, the text string representation, to phys.lo ... phys.hi,
the numerical representation of a physical address within the address space
defined by this device node. The number of cells in the list
phys.lo ... phys.hi is determined by the value of the #address-cells
property of this node.
This function is for devices with #address-cells == 4
Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
grub_aout_load() has a grub_file_t parameter, and depending on what order
includes land in, it's sometimes not defined. This patch explicitly adds
file.h to aout.h so that it will always be defined.
Signed-off-by: Peter Jones <pjones@redhat.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
<grub/machine/loader.h> (for machine arm/efi) and
<grub/machine/kernel.h> (for machine arm/coreboot) will not always
resolve (and will likely not be valid to) if pulled in when building
non-native commands, such as host tools or the "file" command.
So explicitly include them with their expanded pathnames.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Use kernel header struct and magic definition to align (and coexist) with
i386/arm64 ports.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Rename GRUB_LINUX_MAGIC_SIGNATURE GRUB_LINUX_I386_MAGIC_SIGNATURE,
to be usable in code that supports more than one image type.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Replace uses of GRUB_LINUX_MACHINE_HEADER and GRUB_LINUX_CPU_HEADER
with GRUB_<arch>_LINUX_HEADER include guards to prevent issues when
including more than one of them.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
The EFI page definitions and macros are generic and should not be confined
to arm64 headers - so move to efi/memory.h.
Also add EFI_PAGE_SIZE macro.
Update loader sources to reflect new header location.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
The definition of bpb's num_total_sectors_16 and num_total_sectors_32
is that either the 16-bit field is non-zero and is used (in which case
eg mkfs.fat sets the 32-bit field to zero), or it is zero and the
32-bit field is used. Therefore, a BPB is invalid only if *both*
fields are zero; having one field as zero and the other as non-zero is
the case to be expected. (Indeed, according to Microsoft's specification
one of the fields *must* be zero, and the other non-zero.)
This affects all users of grub_chainloader_patch_bpb which are in
chainloader.c, freedos.c, and ntldr.c
Some descriptions of the semantics of these two fields:
https://www.win.tue.nl/~aeb/linux/fs/fat/fat-1.html
The old 2-byte fields "total number of sectors" and "number of
sectors per FAT" are now zero; this information is now found in
the new 4-byte fields.
(Here given in the FAT32 EBPB section but the total sectors 16/32 bit
fields semantic is true of FAT12 and FAT16 too.)
https://wiki.osdev.org/FAT#BPB_.28BIOS_Parameter_Block.29
19 | 2 | The total sectors in the logical volume. If this value is 0,
it means there are more than 65535 sectors in the volume, and the actual
count is stored in "Large Sectors (bytes 32-35).
32 | 4 | Large amount of sector on media. This field is set if there
are more than 65535 sectors in the volume.
(Doesn't specify what the "large" field is set to when unused, but as
mentioned mkfs.fat sets it to zero then.)
https://technet.microsoft.com/en-us/library/cc976796.aspx
0x13 | WORD | 0x0000 |
Small Sectors . The number of sectors on the volume represented in 16
bits (< 65,536). For volumes larger than 65,536 sectors, this field
has a value of zero and the Large Sectors field is used instead.
0x20 | DWORD | 0x01F03E00 |
Large Sectors . If the value of the Small Sectors field is zero, this
field contains the total number of sectors in the FAT16 volume. If the
value of the Small Sectors field is not zero, the value of this field
is zero.
https://staff.washington.edu/dittrich/misc/fatgen103.pdf page 10
BPB_TotSec16 | 19 | 2 |
This field is the old 16-bit total count of sectors on the volume.
This count includes the count of all sectors in all four regions of the
volume. This field can be 0; if it is 0, then BPB_TotSec32 must be
non-zero. For FAT32 volumes, this field must be 0. For FAT12 and
FAT16 volumes, this field contains the sector count, and
BPB_TotSec32 is 0 if the total sector count “fits” (is less than
0x10000).
BPB_TotSec32 | 32 | 4 |
This field is the new 32-bit total count of sectors on the volume.
This count includes the count of all sectors in all four regions of the
volume. This field can be 0; if it is 0, then BPB_TotSec16 must be
non-zero. For FAT32 volumes, this field must be non-zero. For
FAT12/FAT16 volumes, this field contains the sector count if
BPB_TotSec16 is 0 (count is greater than or equal to 0x10000).
(This specifies that an unused BPB_TotSec32 field is set to zero.)
By the way fix offsets in include/grub/fat.h.
Tested with lDebug booted in qemu via grub2's
FreeDOS direct loading support, refer to
https://bitbucket.org/ecm/ldosboot + https://bitbucket.org/ecm/ldebug
Signed-off-by: C. Masloch <pushbx@38.de>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Code is currently ignoring errors from efibootmgr, giving users
clearly bogus output like:
Setting up grub-efi-amd64 (2.02~beta3-4) ...
Installing for x86_64-efi platform.
Could not delete variable: No space left on device
Could not prepare Boot variable: No space left on device
Installation finished. No error reported.
and then potentially unbootable systems. If efibootmgr fails, grub-install
should know that and report it!
We've been using similar patch in Debian now for some time, with no ill effects.
Signed-off-by: Steve McIntyre <93sam@debian.org>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
When we exit grub, we don't free all the memory that we allocated earlier
for our heap region. This can cause problems with setups where you try
to descend the boot order using "exit" entries, such as PXE -> HD boot
scenarios.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
The reboot function calls machine_fini() and then reboots the system.
Currently it lives in lib/ which means it gets compiled into the
reboot module which lives on the heap.
In a following patch, I want to free the heap on machine_fini()
though, so we would free the memory that the code is running in. That
obviously breaks with smarter UEFI implementations.
So this patch moves it into the core. That way we ensure that all
code running after machine_fini() in the UEFI case is running from
memory that got allocated (and gets deallocated) by the UEFI core.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Previously we had multiboot and multiboot2 declaring the same symbols.
This can potentially lead to aliasing and strange behaviours when e.g.
module instead of module2 is used with multiboot2.
Bug: #51137
Add a generic GRUB_PE32_MAGIC definition for the PE 'MZ' tag and delete
the existing one in arm64/linux.h.
Update arm64 Linux loader to use this new definition.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
There is nothing ARM64 (or even ARM) specific about the efi fdt helper
library, which is used for locating or overriding a firmware-provided
devicetree in a UEFI system - so move it to loader/efi for reuse.
Move the fdtload.h include file to grub/efi and update path to
efi/fdtload.h in source code referring to it.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
grub_efi_allocate_pages Essentially does 2 unrelated things:
* Allocate at fixed address.
* Allocate at any address.
To switch between 2 different functions it uses address == 0 as magic
value which is wrong as 0 is a perfectly valid fixed adress to allocate at.
Expose a new function, grub_efi_allocate_pages_real(), making it possible
to specify allocation type and memory type as supported by the UEFI
AllocatePages boot service.
Make grub_efi_allocate_pages() a consumer of the new function,
maintaining its old functionality.
Also delete some left-around #if 1/#else blocks in the affected
functions.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
This patch adds support for virtual LAN (VLAN) tagging. VLAN tagging allows
multiple VLANs in a bridged network to share the same physical network link
but maintain isolation:
http://en.wikipedia.org/wiki/IEEE_802.1Q
* grub-core/net/ethernet.c: Add check, get, and set vlan tag id.
* grub-core/net/drivers/ieee1275/ofnet.c: Get vlan tag id from bootargs.
* grub-core/net/arp.c: Add check.
* grub-core/net/ip.c: Likewise.
* include/grub/net/arp.h: Add vlantag attribute.
* include/grub/net/ip.h: Likewise.
We only support FDT files with EFI on arm and arm64 systems, not
on x86. So move the helper that finds a prepopulated FDT UUID
into its own file and only build it for architectures where it
also gets called.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
If EFI is nice enough to pass us an FDT using configuration tables on 32bit
ARM, we should really try and make use of it.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Searching for a device tree that EFI passes to us via configuration tables
is nothing architecture specific. Move it into generic code.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Modern pvops linux kernels support a p2m list not covered by the
kernel mapping. This capability is flagged by an elf-note specifying
the virtual address the kernel is expecting the p2m list to be mapped
to.
In case the elf-note is set by the kernel don't place the p2m list
into the kernel mapping, but map it to the given address. This will
allow to support domains with larger memory, as the kernel mapping is
limited to 2GB and a domain with huge memory in the TB range will have
a p2m list larger than this.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Modify the page table construction to allow multiple virtual regions
to be mapped. This is done as preparation for removing the p2m list
from the initial kernel mapping in order to support huge pv domains.
This allows a cleaner approach for mapping the relocator page by
using this capability.
The interface to the assembler level of the relocator has to be changed
in order to be able to process multiple page table areas.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Modern pvops linux kernels support an initrd not covered by the initial
mapping. This capability is flagged by an elf-note.
In case the elf-note is set by the kernel don't place the initrd into
the initial mapping. This will allow to load larger initrds and/or
support domains with larger memory, as the initial mapping is limited
to 2GB and it is containing the p2m list.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Get actual version of include/xen/xen.h from the Xen repository in
order to be able to use constants defined there.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Various features and parameters of a pv-kernel are specified via
elf notes in the kernel image. Those notes are part of the interface
between the Xen hypervisor and the kernel.
Instead of using num,bers in the code when interpreting the elf notes
make use of the header supplied by Xen for that purpose.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Currently multiboot2 protocol loads image exactly at address specified in
ELF or multiboot2 header. This solution works quite well on legacy BIOS
platforms. It is possible because memory regions are placed at predictable
addresses (though I was not able to find any spec which says that it is
strong requirement, so, it looks that it is just a goodwill of hardware
designers). However, EFI platforms are more volatile. Even if required
memory regions live at specific addresses then they are sometimes simply
not free (e.g. used by boot/runtime services on Dell PowerEdge R820 and
OVMF). This means that you are not able to just set up final image
destination on build time. You have to provide method to relocate image
contents to real load address which is usually different than load address
specified in ELF and multiboot2 headers.
This patch provides all needed machinery to do self relocation in image code.
First of all GRUB2 reads min_addr (min. load addr), max_addr (max. load addr),
align (required image alignment), preference (it says which memory regions are
preferred by image, e.g. none, low, high) from multiboot_header_tag_relocatable
header tag contained in binary (at this stage load addresses from multiboot2
and/or ELF headers are ignored). Later loader tries to fulfill request (not only
that one) and if it succeeds then it informs image about real load address via
multiboot_tag_load_base_addr tag. At this stage GRUB2 role is finished. Starting
from now executable must cope with relocations itself using whole static and
dynamic knowledge provided by boot loader.
This patch does not provide functionality which could do relocations using
ELF relocation data. However, I was asked by Konrad Rzeszutek Wilk and Vladimir
'phcoder' Serbinenko to investigate that thing. It looks that relevant machinery
could be added to existing code (including this patch) without huge effort.
Additionally, ELF relocation could live in parallel with self relocation provided
by this patch. However, during research I realized that first of all we should
establish the details how ELF relocatable image should look like and how it should
be build. At least to build proper test/example files.
So, this patch just provides support for self relocatable images. If ELF file
with relocs is loaded then GRUB2 complains loudly and ignores it. Support for
such files will be added later.
This patch was tested with Xen image which uses that functionality. However, this Xen
feature is still under development and new patchset will be released in about 2-3 weeks.
Signed-off-by: Daniel Kiper <daniel.kiper@oracle.com>
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Add tags used to pass ImageHandle to loaded image if requested.
It is used by at least ExitBootServices() function.
Signed-off-by: Daniel Kiper <daniel.kiper@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Add grub_relocator64_efi relocator. It will be used on EFI 64-bit platforms
when multiboot2 compatible image requests MULTIBOOT_TAG_TYPE_EFI_BS. Relocator
will set lower parts of %rax and %rbx accordingly to multiboot2 specification.
On the other hand processor mode, just before jumping into loaded image, will
be set accordingly to Unified Extensible Firmware Interface Specification,
Version 2.4 Errata B, section 2.3.4, x64 Platforms, boot services. This way
loaded image will be able to use EFI boot services without any issues.
Signed-off-by: Daniel Kiper <daniel.kiper@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
util/grub-mkimagexx.c is included in a special way into mkimage.c.
Interoperation between defines makes this very tricky. Instead
just have a clean interface and compile util/grub-mkimage*.c separately
from mkimage.c
ipv6 routing in grub2 is broken, we cannot talk to anything outside our local
network or anything that doesn't route in our global namespace. This patch
fixes this by doing a couple of things
1) Read the router information off of the router advertisement. If we have a
router lifetime we need to take the source address and create a route from it.
2) Changes the routing stuff slightly to allow you to specify a gateway _and_ an
interface. Since the router advertisements come in on the link local address we
need to associate it with the global address on the card. So when we are
processing the router advertisement, either use the SLAAC interface we create
and add the route to that interface, or loop through the global addresses we
currently have on our interface and associate it with one of those addresses.
We need to have a special case here for the default route so that it gets used,
we do this by setting the masksize to 0 to mean it encompasses all networks.
The routing code will automatically select the best route so if there is a
closer match we will use that.
With this patch I can now talk to ipv6 addresses outside of my local network.
Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
Define
* GRUB_EFI_PERSISTENT_MEMORY (UEFI memory map type 14) per UEFI 2.5
* GRUB_MEMORY_PERSISTENT (E820 type 7) per ACPI 3.0
* GRUB_MEMORY_PERSISTENT_LEGACY (E820 unofficial type 12) per ACPI 3.0
and translate GRUB_EFI_PERSISTENT_MEMORY to GRUB_MEMORY_PERSISTENT in
grub_efi_mmap_iterate().
Includes
* adding the E820 names to lsmmap
* handling the E820 types in make_efi_memtype()
Suggested-by: Vladimir 'φ-coder/phcoder' Serbinenko <phcoder@gmail.com>
Suggested-by: Andrei Borzenkov <arvidjaar@gmail.com>
PIT isn't available on some of new hardware including Hyper-V. So
use pmtimer for calibration. Moreover pmtimer calibration is faster, so
use it on coreboor where booting time is important.
Based on patch by Michael Chang.
It is not possible to configure encrypted containers on multiple partitions of
the same disk; after the first one all subsequent fail with
disk/cryptodisk.c:978: already mounted as crypto0
Store partition offset in cryptomount descriptor to distinguish between them.
Recent tests have discovered that many of our filesystems have flawed
handling of "." and "..". Rather than attempting to fix it in filesystems
themselves, make the common code fshelp aware of "." and ".." and handle
them in this layer. Add grub_fshelp_find_file_lookup for easy conversion
of BFS, HFS and exFAT which have the same problem and don't use fshelp.
mips_attributes was introduced to work around clang problems with
-msoft-float. Those problems are now fixed and moreover .gnu_attributes
itself is unportable and creates problem with clang.
Revert "mips: Fix soft-float handling."
This partially reverts commit 6a4ecd276e.
Exclusive open on SNP will close all existing protocol instances which
may disable all receive filters on interface. Reinstall them after we
opened protocol exclusively.
Also follow UEFI specification recommendation and stop interfaces when
closing them:
Unexpected system errors, reboots and hangs can occur if an OS is loaded
and the network devices are not Shutdown() and Stopped().
Also by: Mark Salter <msalter@redhat.com>
Closes: 45204
In the past birth was always zero for holes. This feature started
to make use of birth for holes as well, so change code to test for
valid DVA address instead.
This restrict ARP handling to MAC and IP addresses but in practice we need
only this case anyway and other cases are very rar if exist at all. It makes
code much simpler and less error-prone.
canonicalize_file_name clashed with gnulib function. Additionally
it was declared in 2 places: emu/misc.h and util/misc.h. Added
grub_ prefix and removed second declaration.
libgcc for boot environment isn't always present and compatible.
libgcc is often absent if endianness or bit-size at boot is different
from running OS.
libgcc may use optimised opcodes that aren't available on boot time.
So instead of relying on libgcc shipped with the compiler, supply
the functions in GRUB directly.
Tests are present to ensure that those replacement functions behave the
way compiler expects them to.
Add -msoft-float alongside clang arguments to specify ABI.
Specify ABI in asm files explicitly.
This trigers asm warning due to gcc failing to propagate -msoft-float
but it's tolerable.
Previously we supplied only unsigned divisions on platforms that need software
division.
Yet compiler may itself use a signed division. A typical example would be a
difference between 2 pointers which involves division by object size.
GCC 4.9 also generates R_ARM_THM_MOVW_ABS_NC and R_ARM_THM_MOVT_ABS,
as an alternative to ABS32.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Many routers have long router advertisment interval configured by
default. The Neighbor Discovery protocol (RFC4861) has defined default
MaxRtrAdvInterval value as 600 seconds and
MinRtrAdvInterval as 0.33*MaxRtrAdvInterval. This makes
net_ipv6_autoconf fails more often than not as currently it passively
listens the RA message to perfom address autoconfiguration.
This patch tries to send router solicitation to overcome the problem of
long RA interval.
v2:
use cpu_to_be macro for network byte order conversion
add missing error handling
This makes it possible to build generally-useful utilities such as
grub-mount even if the rest of GRUB has not been ported to the target
CPU.
* configure.ac: Add "none" platform. Default to it for unsupported
CPUs rather than stopping with a fatal error. Don't downgrade
x86_64-none to i386. Define COND_real_platform Automake conditional
if the platform is anything other than "none". Don't do any include
directory linking for "none".
* Makefile.am: Skip building grub-core and all bootcheck targets if
!COND_real_platform.
* include/grub/time.h: Don't include <grub/cpu/time.h> if GRUB_UTIL
is defined.
The AML parser implements only a small subset of possible AML
opcodes. On the Fujitsu Lifebook E744 this and another bug in
the parser (incorrect handling of TermArg data types) would lead
to the laptop not turning off (_S5 not found).
* grub-core/commands/acpihalt.c: Support OpAlias in the AML parser;
in skip_ext_op(), handle some Type2Opcodes more correctly (TermArgs
aren't always simply strings!); Add function to skip TermArgs
* include/grub/acpi.h: Add new opcodes
* configure.ac: Remove -m64 from checks for -mcmodel=large and
-mno-red-zone. These are always either unnecessary (x86_64-emu) or
already in TARGET_CFLAGS at this point, and they produce incorrect
results when building for x32.
* grub-core/kern/x86_64/dl.c (grub_arch_dl_relocate_symbols): Cast
pointers to Elf64_Xword via grub_addr_t, in order to work on x32.
* include/grub/x86_64/types.h (GRUB_TARGET_SIZEOF_VOID_P,
GRUB_TARGET_SIZEOF_LONG): Define to 4 on x32.
Commit 588744d0dc caused grub-mkconfig
no longer to be forgiving of trailing spaces on grub-probe output
lines, which among other things means that util/grub.d/10_linux.in
no longer detects LVM. To fix this, make grub-probe's output
delimiting more consistent. As a bonus, this improves the coverage
of the -0 option.
Fixes Debian bug #735935.
* grub-core/disk/cryptodisk.c
(grub_util_cryptodisk_get_abstraction): Add a user-data argument.
* grub-core/disk/diskfilter.c (grub_diskfilter_get_partmap):
Likewise.
* include/grub/cryptodisk.h (grub_util_cryptodisk_get_abstraction):
Update prototype.
* include/grub/diskfilter.h (grub_diskfilter_get_partmap): Likewise.
* util/grub-install.c (push_partmap_module, push_cryptodisk_module,
probe_mods): Adjust for extra user-data arguments.
* util/grub-probe.c (do_print, probe_partmap, probe_cryptodisk_uuid,
probe_abstraction): Use configured delimiter. Update callers.
It enables net boot even when there is no bootp/dhcp server.
* grub-core/net/drivers/ieee1275/ofnet.c: Add grub_ieee1275_parse_bootpath and
call it at grub_ieee1275_net_config_real.
* grub-core/kern/ieee1275/init.c: Add bootpath to grub_ieee1275_net_config.
* include/grub/ieee1275/ieee1275.h: Likewise.
In file included from util/misc.c:36:0:
./include/grub/emu/misc.h:56:1: error: 'libintl_printf' is an unrecognized format function type [-Werror=format=]
char * EXPORT_FUNC(xasprintf) (const char *fmt, ...) __attribute__ ((format (printf, 1, 2))) WARN_UNUSED_RESULT;
^
./include/grub/emu/misc.h:58:1: error: 'libintl_printf' is an unrecognized format function type [-Werror=format=]
The reason is libintl.h which redefines printf as libintl_printf. The problem
is not present in native MinGW build which avoids redefinition. Use
(format (__printf__) instead which is valid replacement in GCC.
v2: add grub-core/lib/libgcrypt/src/g10lib.h
v3: modify g10lib.h during import
In file included from ./include/grub/dl.h:23:0,
from grub-core/lib/libgcrypt-grub/cipher/rfc2268.c:3:
./include/grub/list.h:34:18: warning: conflicting types for 'grub_list_push' [en
abled by default]
void EXPORT_FUNC(grub_list_push) (grub_list_t *head, grub_list_t item);
^
./include/grub/symbol.h:68:25: note: in definition of macro 'EXPORT_FUNC'
# define EXPORT_FUNC(x) x
^
In file included from ./include/grub/fs.h:30:0,
from ./include/grub/file.h:25,
from ./grub-core/lib/posix_wrap/stdio.h:23,
from c:\mingw\include\libintl.h:314,
from ./include/grub/i18n.h:33,
from ./include/grub/misc.h:27,
from ./include/grub/list.h:25,
from ./include/grub/dl.h:28,
from grub-core/lib/libgcrypt-grub/cipher/rfc2268.c:3:
./include/grub/partition.h:106:3: note: previous implicit declaration of 'grub_l
ist_push' was here
grub_list_push (GRUB_AS_LIST_P (&grub_partition_map_list),
^
list.h needs just ATTRIBUTE_ERROR from misc.h; split compiler features
into separate file grub/compiler.h and include it instead.
Use _FILE_OFFSET_BITS macro to distinguish between native MinGW and
32 bit under MinGW-64. The latter does not require fseeko/ftello
redefinition which it already does in case of _FILE_OFFSET_BITS=64.
