Signed-off-by: Amit Walambe <amit.walambe@eurotech.com>
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Amit Walambe <amit.walambe@eurotech.com>
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Zeus console port is wired to a 8250-compatible device (pxa UARTs are
reserved to other uses). This patch allows such a configuration in the
uncompress sequence.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The original patch came from Marc Zyngier where support of 8250-compatible
UART is required to show the uncompress information. Modified a little bit
here, including changes below:
1. #include <mach/regs-uart.h> is actually not necessary
2. introduced uart_{read,write}() for different base and shift
3. introduced uart_is_enabled() and assumed enabled always for
non-PXA uarts
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Marc Zyngier <maz@misterjones.org>
The irq_chip is not yet registered, so no default irq_chip.mask_ack(),
which we have to handle it correctly manually here.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Since PMIC INT pin is a special pin of CPU, the status of PMIC INT pin needs
to be cleared after PMIC IRQ occured. Now append the clear operation in
irq chip handler.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Marvell MMP2 (aka ARMADA610) is a SoC based on PJ4 core. It's
ARMv6 compatible. Support basic interrupt handler and timer,
and basic support for MMP2 based FLINT platform.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Also remove a trailing whitespace while being there.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Add some safety check for CONFIG_PM around zeus_power_off(). Without
it linking can fail like this:
arch/arm/mach-pxa/built-in.o: In function `zeus_power_off':
e800.c:(.text+0x2bc8): undefined reference to `pxa27x_cpu_suspend'
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This function gets only called from scoop_suspend() and scoop_resume() which are
only built in if we have CONFIG_PM set. Make it the same for check_scoop_reg().
This fixes the following warning:
arch/arm/common/scoop.c:143: warning: ‘check_scoop_reg’ defined but not used
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
IRQ_LOCOMO_* are never used elsewhere, remove these definitions. As well
as the cascade of these IRQs. IRQ_LOCOMO_*_BASE changed to IRQ_LOCOMO_*.
IRQ_LOCOMO_LT and IRQ_LOCOMO_SPI are likely to be used in a same way as
IRQ_LOCOMO_KEY.
IRQ_LOCOMO_GPIO and the demultiplex handler should really be living
somewhere else.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
It is not necessary and is over-complicated for IRQ_LOCOMO_KEY to
be a cascaded IRQ of IRQ_LOCOMO_KEY_BASE. Removed and introduced
locomokbd_{open,close} for masking/unmasking of the keyboard IRQ.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Missing AC97 pin configurations are added where pxa_set_ac97_info() are
called for all pxa25x/pxa27x platforms. Where no exact configuration is
provided, use the default as in sound/arm/pxa2xx-ac97-lib.c
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This is really pxa27x specific and should be kept in pxa27x.c. With this
newly introduced function, the original set_resetgpio_mode() is deprecated.
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (40 commits)
DaVinci DM365: Adding support for SPI EEPROM
DaVinci DM365: Adding DM365 SPI support
DaVinci DM355: Modifications to DM355 SPI support
DaVinci: SPI: Adding header file for SPI support.
davinci: dm646x: CDCE clocks: davinci_clk converted to clk_lookup
davinci: clkdev cleanup: remove clk_lookup wrapper, use clkdev_add_table()
DaVinci: DM365: Voice codec support for the DM365 SoC
davinci: clock: let clk->set_rate function sleep
Add SDA and SCL pin numbers to i2c platform data
davinci: da8xx/omap-l1xx: Add EDMA platform data for da850/omap-l138
davinci: build list of unused EDMA events dynamically
davinci: Fix edma_alloc_channel api for EDMA_CHANNEL_ANY case
davinci: Keep count of channel controllers on a platform
davinci: Correct return value of edma_alloc_channel api
davinci: add CDCE949 support on DM6467 EVM
davinci: add support for CDCE949 clock synthesizer
davinci: da850/omap-l138 EVM: register for suspend support
davinci: da850/omap-l138: add support for SoC suspend
davinci: add power management support
DaVinci: DM365: Changing default queue for DM365.
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (62 commits)
Input: atkbd - release previously reserved keycodes 248 - 254
Input: add KEY_WPS_BUTTON definition
Input: ads7846 - add regulator support
Input: winbond-cir - fix suspend/resume
Input: gamecon - use pr_err() and friends
Input: gamecon - constify some of the setup structures
Input: gamecon - simplify pad type handling
Input: gamecon - simplify coordinate calculation for PSX
Input: gamecon - fix some formatting issues
Input: gamecon - add rumble support for N64 pads
Input: wacom - add device type to device name string
Input: s3c24xx_ts - report touch only when stylus is down
Input: s3c24xx_ts - re-enable IRQ on resume
Input: wacom - constify product features data
Input: wacom - use per-device instance of wacom_features
Input: sh_keysc - enable building on SH-Mobile ARM
Input: wacom - get features from driver info
Input: rotary-encoder - set gpio direction for each requested gpio
Input: sh_keysc - update the driver with mode 6
Input: sh_keysc - switch to using bitmaps
...
The DM365 Spectrum Digital EVM comes with an EEPROM
connected to SPI0.
This patch adds support for the SPI EEPROM.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds SPI init for DM365.
It does the following
1) Initializes SPI0
2) Defines resources to be used by SPI0
3) Adds platform data for SPI0
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch does the following
1) Minor change to the SPI clocks making it
similar to DM365.
2) Changing the interrupt used by SPI0
3) Adding EDMA resources that can be used by SPI0
4) Adding platform specific data.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds "spi.h" header file that will be used by board and
architecture specific code.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Remove unneeded 'struct davinci_clk' wrapper around 'struct
clk_lookup' and use clk_lookup directly.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (252 commits)
ASoC: Check progress when reporting periods from i.MX FIQ handler
ASoC: Remove a unused variables from i.MX FIQ runtime data
ALSA: hda - Add/fix ALC269 FSC and Quanta models
ALSA: hda - Add ALC670 codec support
OMAP4: PMIC: Add support for twl6030 codec
ALSA: hda - remove unnecessary msleep on power state transitions
usb/gadget/{f_audio,gmidi}.c: follow recent changes in audio.h
ASoC: fsi: Modify over/under run error settlement
ASoC: OMAP4: Add McPDM platform driver
ASoC: OMAP4: Add support for McPDM
ASoC: OMAP: data_type and sync_mode configurable in audio dma
ALSA: hda - Add missing description in HD-Audio-Models.txt
ALSA: add support for Macbook Air 2,1 internal speaker
ALSA: usbaudio: consolidate header files
ALSA: usbmixer: bail out early when parsing audio class v2 descriptors
ALSA: usbaudio: implement basic set of class v2.0 parser
ALSA: usbaudio: introduce new types for audio class v2
ALSA: usbaudio: parse USB descriptors with structs
ALSA: hda - enable snoop for Intel Cougar Point
ALSA: hda - Remove identical definitions for macmini3 model
...
When we reach the loop, len is at least 1, we only stay in the loop when
len is at least MAX_BYTE_COUNT + 1, MAX_BYTE_COUNT is subtracted in each
iteration. So when we leave the loop, or didn't take it, len is at least 1.
Testing whether len is non-zero appears redundant.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (362 commits)
V4L-DVB: cx88-dvb: remove extra attribution for core
V4L/DVB: v4l: soc_camera: fix bound checking of mbus_fmt[] index
V4L/DVB: Add support for SMT7020 to cx88
V4L/DVB: radio-si470x: Use UTF-8 encoding on a comment
V4L/DVB: MAINTAINERS: Telegent tlg2300 section fix
V4L/DVB: gspca_stv06xx: Add support for camera button
V4L/DVB: gspca_ov519: add support for the button on ov511 based cams
V4L/DVB: gspca_ov519: Add support for the button on ov518 based cams
V4L/DVB: gspca_ov519: add support for the button on ov519 based cams
V4L/DVB: gspca_main: Fix a compile error when CONFIG_INPUT is not set
V4L/DVB: gspca_main: some input error handling fixes
V4L/DVB: gspca_main: Allow use of input device creation code for non int. inputs
V4L/DVB: gspca_pac7302: much improved exposure control
V4L/DVB: gspca_sonixb: Make sonixb driver handle pas106 and pas202 cameras
V4L/DVB: gspca_sonixb: pas106: fixup bright ctrl and add gain and exposure ctrls
V4L/DVB: Documentation: gspca.txt: update known mr97310a cams
V4L/DVB: gspca_mr97310a: add support for the Sakar 1638x CyberPix
V4L/DVB: gscpa_sonixb: limit ov7630 max framerate at 640x480
V4L/DVB: gspca_sonixb: pas202: fixup brightness ctrl and add gain and exposure ctrls
V4L/DVB: gscpa_sonixb: Differentiate between sensors with a coarse and fine expo ctrl
...
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/xfs-vipt:
xfs: fix xfs to work with Virtually Indexed architectures
sh: add mm API for DMA to vmalloc/vmap areas
arm: add mm API for DMA to vmalloc/vmap areas
parisc: add mm API for DMA to vmalloc/vmap areas
mm: add coherence API for DMA to vmalloc/vmap areas
This patch adds following changes:-
1) add sub device configuration data for TVP5146 used by vpfe capture
2) registers platform devices for vpfe_capture, isif and vpss
3) defines hardware resources for the devices listed under 2)
4) defines clock aliase for isif driver
5) adding setup_pinmux() for isif
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Murali Karicheri <mkaricheri@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pxa_camera init() callback is sometimes abused to setup MFP for PXA CIF, or
even to request GPIOs to be used by the camera *sensor*. These initializations
can be performed statically in machine init functions.
The current semantics for this init() callback is ambiguous anyways, it is
invoked in pxa_camera_activate(), hence at device node open, but its users use
it like a generic initialization to be done at module init time (configure
MFP, request GPIOs for *sensor* control).
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 2552fc2 changed the way the decompressor decides if it is safe
to decompress the kernel directly to its final location. Unfortunately,
it took the top of the compressed data as being the stack pointer,
which it is for ROM=n cases. However, for ROM=y, the stack pointer
is not relevant, and results in the wrong answer.
Fix this by explicitly storing the end of the biggybacked data in the
decompressor, and use that to calculate the compressed image size.
CC: <stable@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Correct instances where tca6416 is misspelt as tca6516 in
the board-am3517evm file.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are multiple devices connected to I2C bus on AM3517EVM
(for instance audio codec, IO expander etc). Enable I2C support
in the default kernel configuration for AM3517 EVM.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enabling OMAP_MUX in defconfig as it is required for EHCI to work.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding GPIO mux config used for PHY reset of EHCI port on base board.
We get below failure message without this patch,
"hub 1-0:1.0: unable to enumerate USB device on port 1"
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some of the features are not enabled by default in zoom3 defconfig.
This patch enables:
- MMC Resume
- TWL4030 RTC driver
- Debug File system
Build and boot tested on Zoom3 board.
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit b63128e812 broke the pin muxing
for I2C busses that are enabled from the kernel command line.
Fix this by defining the board registration function omap_register_i2c_bus
in common platform code as it was before but keep the muxing in architecture
dependent files.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We used to build decompressors with -Dstatic= to avoid any local data
being generated. The problem is that local data generates GOTOFF
relocations, which means we can't relocate the data relative to the
text segment.
Global data, on the other hand, goes through the GOT, and can be
relocated anywhere.
Unfortunately, with the new decompressors, this presents a problem
since they declare static data within functions, and this leads to
stack overflow.
Fix this by separating out the decompressor code into a separate file,
and removing 'static' from BSS data in misc.c.
Also, discard the .data section - this means that should we end up
with read/write initialized data, the decompressor will fail to link
and the problem will be obvious.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Removed selection of COMMON_CLKDEV by CONFIG_ARCH_MX5. This is handled
in 03e09cd890.
arch/arm/plat-mxc/iomux-mx1-mx2.c was moved to
arch/arm/plat-mxc/iomux-v1.c in 5e2e95f520
and got bug fixed in 5c17ef878f. The bug
in arch/arm/plat-mxc/iomux-v1.c isn't present any more since
bac3fcfad5, so
arch/arm/plat-mxc/iomux-mx1-mx2.c is simply deleted.
Conflicts:
arch/arm/plat-mxc/Kconfig
arch/arm/plat-mxc/Makefile
arch/arm/plat-mxc/iomux-mx1-mx2.c
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Because AP4 board has capacitor for KEYSC,
we need much time for waiting.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now the omap4 clock framework is in mainline and clk_get_rate()
is functional. Hence reomve the hardcoded clock hacks.
This patch also fixes
Division by zero in kernel.
Backtrace:
[<c0025fb8>] (dump_backtrace+0x0/0x110) from [<c017febc>] (dump_stack+0x18/0x1c)
r7:60000093 r6:c0641050 r5:c0223e78 r4:c02126b4
[<c017fea4>] (dump_stack+0x0/0x1c) from [<c00260fc>] (__div0+0x18/0x20)
[<c00260e4>] (__div0+0x0/0x20) from [<c01431fc>] (Ldiv0+0x8/0x10)
[<c00318d4>] (omap_dm_timer_stop+0x0/0xb0) from [<c002c148>] (omap2_gp_timer_set_mode+0x1c/0x68)
r5:c0223e78 r4:00000000
[<c002c12c>] (omap2_gp_timer_set_mode+0x0/0x68) from [<c0063270>] (clockevents_set_mode+0x30/0x64)
r5:c020cae0 r4:00000000
[<c0063240>] (clockevents_set_mode+0x0/0x64) from [<c00632fc>] (clockevents_exchange_device+0x30/0x9c)
r5:c020cae0 r4:c02146e0
[<c00632cc>] (clockevents_exchange_device+0x0/0x9c) from [<c00636e0>] (tick_notify+0x17c/0x404)
r7:00000000 r6:c0641050 r5:00000000 r4:c020cae0
[<c0063564>] (tick_notify+0x0/0x404) from [<c005d5fc>] (notifier_call_chain+0x34/0x78)
[<c005d5c8>] (notifier_call_chain+0x0/0x78) from [<c005d684>] (__raw_notifier_call_chain+0x1c/0x24)
[<c005d668>] (__raw_notifier_call_chain+0x0/0x24) from [<c005d6ac>] (raw_notifier_call_chain+0x20/0x28)
[<c005d68c>] (raw_notifier_call_chain+0x0/0x28) from [<c0062e78>] (clockevents_do_notify+0x1c/0x24)
[<c0062e5c>] (clockevents_do_notify+0x0/0x24) from [<c0062f18>] (clockevents_register_device+0x98/0xd0)
[<c0062e80>] (clockevents_register_device+0x0/0xd0) from [<c001a194>] (percpu_timer_setup+0x80/0x9c)
r7:00000000 r6:00000002 r5:00000002 r4:00000003
[<c001a114>] (percpu_timer_setup+0x0/0x9c) from [<c000e9f0>] (smp_prepare_cpus+0xb0/0xe8)
[<c000e940>] (smp_prepare_cpus+0x0/0xe8) from [<c00084e8>] (kernel_init+0x5c/0x1fc)
r7:00000000 r6:00000000 r5:00000000 r4:c001b8a4
[<c000848c>] (kernel_init+0x0/0x1fc) from [<c0046c50>] (do_exit+0x0/0x604)
r7:00000000 r6:00000000 r5:00000000 r4:00000000
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4 platform the iclk control is completly under hardware control
and no software control is available.
This difference w.r.t previous OMAP's needs all the common driver
accross OMAP's , cpu_is_xxxx() checks. To avoid poulluting the
drivers dummy clock nodes are created (The autogeneration
script has been updated accordingly).
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: made OMAP1 dummy_ck common and edited patch to reuse that]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
All leaf clock nodes are renamed for OMAP4 to have a clk name which
end with a _ick or a _fck. This is done so that the naming convention
is same as that followed on older OMAPs.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Simplify the code in the omap2_clk_disable() and omap2_clk_enable()
functions, reducing levels of indentation. This makes the code easier
to read. Add some additional debugging pr_debug()s here also to help
others understand what is going on.
Revise the omap2_clk_disable() logic so that it now attempts to
disable the clock's clockdomain before recursing up the clock tree.
Simultaneously, ensure that omap2_clk_enable() is called on parent
clocks first, before enabling the clockdomain. This ensures that a
parent clock's clockdomain is enabled before the child clock's
clockdomain. These sequences should be the inverse of each other.
Revise the omap2_clk_enable() logic so that it now cleans up after
itself upon encountering an error. Previously, an error enabling a
parent clock could have resulted in inconsistent usecounts on the
enclosing clockdomain.
Remove the trivial _omap2_clk_disable() and _omap2_clk_enable() static
functions, and replace it with the clkops calls that they were
executing.
For all this to work, the clockdomain omap2_clkdm_clk_enable() and
omap2_clkdm_clk_disable() code must not return an error on clockdomains
without CLKSTCTRL registers; so modify those functions to simply return 0
in that case.
While here, add some basic kerneldoc documentation on both functions,
and get rid of some old non-CodingStyle-compliant comments that have
existed since the dawn of time (at least, the OMAP clock framework's
time).
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
The OMAP2 and OMAP3 boot-time MPU rate change code is almost
identical. Merge them into mach-omap2/clock.c, and add kerneldoc
documentation.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
_clkdm_add_autodeps() and _clkdm_del_autodeps() will attempt to dereference
a NULL pointer if no autodeps were supplied to clkdm_init().
Based on a patch from Roel Kluin <roel.kluin@gmail.com> - thanks Roel.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Roel Kluin <roel.kluin@gmail.com>
Add support for categorizing and iterating over hardware IP blocks by
the "class" of the IP block. The class is the type of the IP block:
e.g., "timer", "timer1ms", etc. Move the OCP_SYSCONFIG/SYSSTATUS data
from the struct omap_hwmod into the struct omap_hwmod_class, since
it's expected to stay consistent for each class. While here, fix some
comments.
The hwmod_class structures in this patch were designed and proposed by
Benoît Cousson <b-cousson@ti.com> and were refined in a discussion
between Thara Gopinath <thara@ti.com>, Kevin Hilman
<khilman@deeprootsystems.com>, and myself.
This patch uses WARN() lines that are longer than 80 characters, as
Kevin noted a broader lkml consensus to increase greppability by
keeping the messages all on one line.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Cc: Thara Gopinath <thara@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Follow the scheme used for IRQs. By default 16 GPIOs are allocated
for board use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Updates arch/arm Kconfig and Makefile for building the S5PV210 support.
Also modifies the plat-s5p Kconfig file to include the support for plat-s5p
for S5PV210.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds IRQ support for S5PV210. This patch adds interrupt
register definitions, IRQ definitions for various interrupt sources
and new VIC base for VIC2 and VIC3 in plat-s5p common irq code.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds clock support for S5PV210. This patch adds the clock
register definitions and the various system clocks in S5PV210.
Clocks that are common to other S5P SoC'c are added in the common
S5P clock support.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds support for Samsung S5PV210 CPU. This patch also adds
an entry for S5PV210 cpu in plat-s5p cpu table.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The clk_round_rate() functions in the U300 clocking will always
select the lowest clocking frequency due to inverted rounding
comparisons. Fix this.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The timer defines are only used in core.c. Move them so
they will not be globaly exposed.
While here, add additional defines to document the magic
numbers used in the registers. Also, add some comments
for clarification.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The GPIO support in core.c handles the interrupt support for GPIO
ports A, B, and F. The gpiolib implementation in gpio.c needs to
access the function ep93xx_gpio_int_mask when a gpio pin is made
an output and ep93xx_gpio_update_int_params in order to update
the registers.
Moving this support from core.c to gpio.c allows making the two
functions static. It also keeps all the GPIO handling together in one
file.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch 5879/1: ep93xx: define magic numbers for pll1 and pll2 broke
the ep93xx build due to one missing rename of EP93XX_SYSCON_CLOCK_SET2.
The correct name should be EP93XX_SYSCON_CLKSET2.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add ARM_L1_CACHE_SHIFT_6 to arch/arm/Kconfig to allow CPUs with
L1 cache lines which are 64bytes to indicate this without having to
alter the arch/arm/mm/Kconfig entry each time.
Update the mm Kconfig so that ARM_L1_CACHE_SHIFT default value
uses this and change OMAP3 and S5PC1XX to select ARM_L1_CACHE_SHIFT_6.
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Code should be able to #include any header file without the fear that
the header file will go allocating memory. This is a coding style
issue, similar to commit 82e9bd5885.
Move the existing hwmod data from .h files to .c files.
While here, convert "omap34xx" to "omap3xxx" in the hwmod files, since
most of these structures should be reusable across all OMAP3 chips.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
The OMAP hwmod core code is intended to use SoC IP block description
structures that are autogenerated from TI's OMAP hardware database.
Currently the hwmod code uses clkdev device + connection addressing to
identify clocks. This causes problems in the hwmod autogeneration
process, since the TI hardware database doesn't use platform_device or
clkdev addressing; it uses a single clock signal name string, which
tends to bear some resemblance to what is used in the OMAP TRMs. This
patch converts the hwmod code and existing data to use omap_clk_get_by_name(),
introduced in the previous patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
The OMAP hwmod core code is intended to use SoC IP block description
structures that are autogenerated from TI's OMAP hardware database.
Currently the hwmod code uses clkdev device + connection addressing to
identify clocks. This causes problems in the hwmod autogeneration
process, since the TI hardware database doesn't use platform_device or
clkdev addressing; it uses a single clock signal name string, which
tends to bear some resemblance to what is used in the OMAP TRMs. This
patch adds a non-exported function to the OMAP clock code,
omap_clk_get_by_name(). A subsequent patch will convert the hwmod
code to use this function.
This function is for use only by core code, and practically, no other
code outside the hwmod code should need it. Device driver code in the
kernel must not use this function, which is why it is not exported.
Drivers should use the appropriate clock alias provided by the clkdev
data structures, so driver code can be completely SoC-independent.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Add necessary clk_sel definitions to clock framework to allow changing
dpll4_m5_ck_3630 rate. This is used by the ISP driver.
Signed-off-by: Vimarsh Zutshi <vimarsh.zutshi@nokia.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Get rid of the ALWAYS_ENABLED clock flag - it doesn't actually do anything.
(The OMAP4 clock autogeneration scripts have been updated accordingly.)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
The RATE_FIXED clock flag is pointless. In the OMAP1 clock code, it
simply causes the omap1_clk_round_rate() function to return the
current rate of the clock. omap1_clk_round_rate(), however, should
never be called for a fixed-rate clock, since none of these clocks
have a .round_rate function pointer set in their struct clk records.
Similarly, in the OMAP2+ clock code, the RATE_FIXED flag just causes
the clock code to emit a warning if the OMAP clock maintainer was
foolish enough to add a .round_rate function pointer to a fixed-rate
clock. "Doctor, it hurts when I pretend that a fixed-rate clock is
rate-changeable." "Then don't pretend that a fixed-rate clock is
rate-changeable." It has no functional value. This patch drops the
RATE_FIXED clock flag, removing it from all clocks that are so marked.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
All of the clocks that are marked with DELAYED_APP are changed as part
of the virt_prcm_set OPP virtual clock. On 24xx, these clocks all
need to be changed as part of a group to keep the clock tree
functional - hence the need for the VALID_CONFIG bit, which is not
present on later OMAPs. These clocks should not be rate-changed
independently. So prevent these clocks from being changed
independently by dropping their .round_rate and .set_rate function
pointers. It then turns out that the DELAYED_APP clock flag is no
longer useful, so drop it and the associated code and renumber the
clock flags.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
func_96m_ck was incorrectly marked as being rate-selectable, when in
fact it is only parent-selectable. Remove the .set_rate and .round_rate
function pointers for this clk.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In preparation for multi-OMAP2 kernels, split
mach-omap2/clock2xxx_data.c into mach-omap2/clock2420_data.c and
mach-omap2/clock2430_data.c. 2430 uses a different device space
physical memory layout than past or future OMAPs, and we use a
different virtual memory layout as well, which causes trouble for
architecture-level code/data that tries to support both. We tried
using offsets from the virtual base last year, but those patches never
made it upstream; so after some discussion with Tony about the best
all-around approach, we'll just grit our teeth and duplicate the
structures. The maintenance advantages of a single kernel config that
can compile and boot on OMAP2, 3, and 4 platforms are simply too
compelling.
This approach does have some nice benefits beyond multi-OMAP 2 kernel
support. The runtime size of OMAP2420-specific and OMAP2430-specific
kernels is smaller, since unused clocks for the other OMAP2 chip will
no longer be compiled in. (At some point we will mark the clock data
__initdata and allocate it during registration, which will eliminate
the runtime memory advantage.) It also makes the clock trees slightly
easier to read, since 2420-specific and 2430-specific clocks are no
longer mixed together.
This patch also splits 2430-specific clock code into its own file,
mach-omap2/clock2430.c, which is only compiled in for 2430 builds -
mostly for organizational clarity.
While here, fix a bug in the OMAP2430 clock tree: "emul_ck" was
incorrectly marked as being 2420-only, when actually it is present on
both OMAP2420 and OMAP2430.
Thanks to Tony for some good discussions about how to approach this
problem.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
clock34xx_data.c now contains data for the OMAP34xx family, the
OMAP36xx family, and the OMAP3517 family, so rename it to
clock3xxx_data.c. Rename clock34xx.c to clock3xxx.c, and move the
chip family-specific clock functions to clock34xx.c, clock36xx.c, or
clock3517.c, as appropriate. So now "clock3xxx.*" refers to the OMAP3
superset.
The main goal here is to prepare to compile chip family-specific clock
functions only for kernel builds that target that chip family. To get to
that point, we also need to add CONFIG_SOC_* options for those other
chip families; that will be done in future patches, planned for 2.6.35.
OMAP4 is also affected by this. It duplicated the OMAP3 non-CORE DPLL
clkops structure. The OMAP4 variant of this clkops structure has been
removed, and since there was nothing else currently in clock44xx.c, it
too has been removed -- it can always be added back later when there
is some content for it. (The OMAP4 clock autogeneration scripts have been
updated accordingly.)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ranjith Lohithakshan <ranjithl@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
After the clkdev conversion, the struct clk.id field became
superfluous, so, drop it. Bring the clock names closer to the TRMs
and ensure they are unique for debugfs.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
There are now only eight OMAP clock flags, so renumber the flags to
fit in a u8 and shrink the size of struct clk.flags from a u32 to a
u8. The intention is to save memory.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
It turns out that the only purpose of the CONFIG_PARTICIPANT clock
flag is to prevent omap2_clk_set_rate() and omap2_clk_set_parent()
from being executed on clocks with that flag set. The rate-changing
component can be more directly accomplished by dropping the .set_rate
and .round_rate function pointers from those CONFIG_PARTICIPANT struct
clks. As far as the parent-changing component is concerned, it turns
out that none of the CONFIG_PARTICIPANT clocks have multiple parent
choices, so all that is necessary is for omap2_clk_set_parent() to
bail out early if the new parent is equal to the old parent.
Implement this change and get rid of the flag, which has always had a
confusing name (it appears to be a Kconfig option, falsely).
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
The DELAYED_APP flag is effective only with clksel clocks, so drop it from
clocks that are not rate-changeable or that use non-clksel rate changing code
(e.g., virt_prcm_set).
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
According to the OMAP242x TRM Rev X Figure 5-15 "Clock Output Control
- Functional Clocks 2", the GFX functional clocks should be marked
both DELAYED_APP and CONFIG_PARTICIPANT, meaning that their rates must
be reprogrammed as part of a larger OPP set change.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
The CLOCK_IN_OMAP4430 clock flag is not currently needed in the OMAP4
ES1 clock tree, and platform discrimination via clock flags is
deprecated in favor of the clkdev mechanism, so, drop it. (The OMAP4
clock tree autogeneration script has been updated accordingly.)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
The maximum DPLL multiplier (M) values for OMAP2xxx and OMAP3xxx are
one increment higher than they should be. See for example the
OMAP242x TRM Rev X Section 5.10.6 "Clock Generator Registers" and the
OMAP36xx TRM Rev C Table 3-202 "CM_CLKSEL1_PLL". Programming a 0 into
the DPLL's M register bitfield is valid for OMAP2/3 and indicates that
the DPLL should enter MN-bypass mode. Also, increase the minimum
multiplier (M) value for the DPLL rate rounding code from 1 to 2, to
ensure that it does not inadvertently put the DPLL into bypass.
Note that the register documentation in the OMAP2xxx and OMAP3xxx TRMs
does not make clear that the actual DPLL divider value (the "N") is
the content of the appropriate register bitfield for the N value,
_plus one_. (In other words, an N register bitfield of 0 indicates a
DPLL divider value of 1.) This is only clearly documented in the
OMAP4430 TRM, in, for example, OMAP4430 TRM Rev A Table 3-1167
"CM_CLKSEL_DPLL_USB".
While here, update copyrights, add kerneldoc for struct dpll_data,
drop the unused struct dpll_data.max_tolerance field, remove some
unnecessary #includes in DPLL-related code, and replace the #include
of <linux/module.h> with <linux/list.h>, which is what was really
needed. The OMAP4 clock autogenerator script has been updated
accordingly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
In 3630, DPLL4M2 output can be 96MHz or 192MHz (for SGX to run at
192). This patch has changes to support this feature. 96MHz clock is
generated by dividing 192Mhz clock by 2 using CM_CLKSEL_CORE register.
SGX can select Core Clock, 192MHz clock or CM_96M_FCLK as it's
functional clock. In summary changes done are:
1. Added a feature called omap3_has_192mhz_clk and enabled for 3630
2. Added a new clock node called omap_192m_alwon_ck
3. Made omap_96m_alwon_fck to derive its clock from omap_192m_alwon_ck
Signed-off-by: Vishwanath BS <Vishwanath.bs@ti.com>
[paul@pwsan.com: fixed whitespace]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Divider (M2, M3, M4, M5 and M6) field width has been increased by 1 bit
in 3630. This patch has changes to accommodate this in CM dynamically
based on chip version.
Basically new clock nodes have been added for 3630 DPLL4 M2,M3,M4,M5 and
M6 and value of these nodes are used if cpu type is 3630.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
[paul@pwsan.com: updated to apply on 2.6.34 queue; comments added]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DPLL4 for 3630 introduces a changed block called j type dpll, requiring
special divisor bits and additional reg fields. To allow for silicons to
use this, this is introduced as a flag and is enabled for 3630 silicon.
OMAP4 also has j type dpll for usb.
Tested with 3630 ZOOM3 and OMAP3430 ZOOM2
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vishwanath BS <Vishwanath.bs@ti.com>
[paul@pwsan.com: added some comments; updated copyrights and credits; fixed
some style issues]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
A check is added for avoiding the sleep/wakeup dependency updates
for OMAP4 as the structures for the dependencies are currently absent.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
[paul@pwsan.com: added warnings, explanatory comment, copyright update]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch implements a workaround for the DPLL HS divider limitation
in OMAP3630 as given by Errata ID: i556.
Errata:
When PWRDN bit is set, it resets the internal HSDIVIDER divide-by value (Mx).
The reset value gets loaded instead of the previous value.
The following HSDIVIDERs exhibit above behavior:
. DPLL4 : M6 / M5 / M4 / M3 / M2 (CM_CLKEN_PLL[31:26] register bits)
. DPLL3 : M3 (CM_CLKEN_PLL[12] register bit).
Work Around:
It is mandatory to apply the following sequence to ensure the write
value will
be loaded in DPLL HSDIVIDER FSM:
The global sequence when using PWRDN bit is the following:
. Disable Mx HSDIVIDER clock output related functional clock enable bits
(in CM_FCLKEN_xxx / CM_ICLKEN_xxx)
. Enable PWRDN bit of HSDIVIDER
. Disable PWRDN bit of HSDIVIDER
. Read current HSDIVIDER register value
. Write different value in HSDIVIDER register
. Write expected value in HSDIVIDER register
. Enable Mx HSDIVIDER clock output related functional clocks
(CM_FCLKEN_xxx / CM_ICLKEN_xxx)
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Vijaykumar GN <vijaykumar.gn@ti.com>
[paul@pwsan.com: updated patch to apply; made workaround function static;
marked as being 36xx-specific]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds support in omap device layer to register devices
as early platform devices. Certain devices needed during system boot up
like timers, gpio etc can be registered as early devices. This will
allow for them to be probed very early on during system boot up.
This patch adds a parameter is_early_device in omap_device_build.
Depending on this parameter a call to early_platform_add_devices
or platform_register_device is made.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In OMAP3 Some modules like Smartreflex do not have the regular sysconfig
register.Instead clockactivity bits are part of another register at a
different bit position than the usual bit positions 8 and 9.
In OMAP4, a new scheme is available due to the new protocol
between the PRCM and the IPs. Depending of the scheme, the SYSCONFIG
bitfields position will be different.
The IP_REVISION register should be at offset 0x00.
It should contain a SCHEME field. From this we can determine whether
the IP follows legacy scheme or the new scheme.
31:30 SCHEME Used to distinguish between old scheme and current.
Read 0x0: Legacy protocol.
Read 0x1: New PRCM protocol defined for new OMAP4 IPs
For legacy IP
13:12 MIDLEMODE
11:8 CLOCKACTIVITY
6 EMUSOFT
5 EMUFREE
4:3 SIDLEMODE
2 ENAWAKEUP
1 SOFTRESET
0 AUTOIDLE
For new OMAP4 IP's, the bit position in SYSCONFIG is (for simple target):
5:4 STANDBYMODE (Ex MIDLEMODE)
3:2 IDLEMODE (Ex SIDLEMODE)
1 FREEEMU (Ex EMUFREE)
0 SOFTRESET
Unfortunately In OMAP4 also some IPs will not follow any of these
two schemes. This is the case at least for McASP, SmartReflex
and some security IPs.
This patch introduces a new field sysc_fields in omap_hwmod_sysconfig which
can be used by the hwmod structures to specify the offsets for the
sysconfig register of the IP.Also two static structures
omap_hwmod_sysc_type1 and omap_hwmod_sysc_type2 are defined
which can be used directly to populate the sysc_fields if the IP follows
legacy or new OMAP4 scheme. If the IP follows none of these two schemes
a new omap_hwmod_sysc_fields structure has to be defined and
passed as part of omap_hwmod_sysconfig.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DPLL_FREQSEL field in CLKEN_PLL register is no longer valid for
OMAP3630. So remove references to that.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
[paul@pwsan.com: added comment fix from Sergei Shtylyov]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
- missing return in omap_prcm_get_reset_sources()
- potential use of uninitialized variable in omap_prcm_arch_reset()
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch checks if clk_get() returned success for
the clocks used in function omap2_clk_arch_init().
This version incorporates review comments from
Kevin Hilman and Paul Walmsley.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds clock support for the following AM35xx modules
- Ethernet MAC
- CAN Controller (HECC)
- New MUSB OTG Controller with integrated Phy
- Video Processing Front End (VPFE)
- Additional UART (UART4)
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Current implementation defines clock idle state indicators based on the
cpu information (cpu_is_omap24xx() or cpu_is_omap34xx()) in a system wide
manner. This patch extends the find_idlest() function in clkops to pass
back the idle state indicator for that clock, thus allowing idle state
indicators to be defined on a per clock basis if required.
This is specifically needed on AM35xx devices as the new IPSS clocks
indicates the idle status (0 is idle, 1 is ready) in a way just
opposite to how its handled in OMAP3 (0 is ready, 1 is idle).
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
[paul@pwsan.com: updated to apply after commit 98c45457 et seq.]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds counters to keep track of whether the powerdomain
logic or software controllable memory banks are turned off when
the power domain enters retention. During power domain retention
if logic gets turned off, the scenario is known as Open Switch Retention.
Also during retention s/w controllable memory banks of a power
domain can be chosen to be kept in retention or off.
This patch adds one counter per powerdomain to track the power domain
logic state during retention. Number of memory bank state counters
added depends on the number of software controllable memory banks
of the powerdomain. To view these counters do
cat ../debug/pm_debug/count
Signed-off-by: Thara Gopinath <thara@ti.com>
[paul@pwsan.com: conditional expressions simplified; counter increment
code moved to its own function]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds the flag .pwrsts_logic_ret info for the core power domain
in the associated powerdomain structure. This flag specifies the states
core domain logic can hit in event of the domain entering retention.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds APIs pwrdm_read_logic_retst and
pwrdm_read_mem_retst for reading the next programmed
logic and memory state a powerdomain is to hit in event
of the next power domain state being retention.
These are needed for OSWR support.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Added definitions for OMAP3430ES2_ST_SGX_SHIFT and OMAP3430ES2_ST_SGX_MASK
as these were missing.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add _MASK suffix to CM_FCLKEN_IVA2 bitfieds to conform with the rest
of the usage in cm-regbits-34xx.h of using _SHIFT and _MASK suffixes.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The omap_device_[enable|idle|shutdown] functions print a warning
when called from an invalid state. Print the invalid state in
the warning messages. This also uses __func__ to get the function
name.
Also, move the entire print string onto a single line to facilitate
grepping or error messages. Recent discussions on LKML show
strong preference for grep-able code vs. strict 80 column limit.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The omap_device struct contains a 'struct platform_device'. Normally,
converting a platform_device pointer to an omap_device pointer
consists of simply doing a container_of(), as is done currently by the
to_omap_device() macro.
However, if this is attempted when using platform_device that has not
been created as part of the omap_device creation, the container_of()
will point to a memory location before the platform_device pointer
which will contain random data.
Therefore, we need a way to detect valid omap_device pointers. This
patch solves this by using the simple magic number approach.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Move check/set/get_timings() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move set/get_wss() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move enable/disable/suspend/resume from omap_dss_device to
omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move update() and sync() from omap_dss_device to omap_dss_driver.
Also, update was hardcoded to use virtual channel 0. This patch adds a
parameter that specifies the VC.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move set/get_update_mode() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move enable/get_te() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move get_recommended_bpp() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move get_resolution() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move enable/disable_channel() from omap_dss_device to overlay manager.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move wait_vsync() from omap_dss_device to overlay manager.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move get/set_rotate() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move set/get_mirror() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move memory_read() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move run_test() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
ARCH_MXC_IOMUX_V3 is not specific to the i.MX25 PDK platform. Thus,
ARCH_MXC_IOMUX_V3 should be selected by ARCH_MX25.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch is to be applied into Sascha's mxc-master branch.
Fix ckih2 parameter in mx51_clocks_init funtion. CKIH2 pin is left unconnected on Babbage.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
SSI5 on the CPU is connected to the PMIC module to provide audio support
so unconditionally configure the relevant pins on the CPU to route out
the signals.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
mxc_gpio_mode checks for invalid pins and so it returns zero for
success, -EINVAL for invalid pins.
While at it, remove definitions of GPIO_PORT_MAX removed as they are
unused now.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Addionally make iomux-mx*.h headers stand-alone and similar to iomux-v3
platform files should include their platform iomux header from now on.
For now iomux.h simply includes all iomux-v1 platform headers and so
provides compatibility until all files are converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- use __MACH_IOMUX_MX3_H__ as header protector analogous to
<mach/mx...h>
- use tabs for indention
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- use __MACH_IOMUX_MX2x_H__ as header protector analogous to
<mach/mx...h>
- use tabs for indention
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- use __MACH_IOMUX_MX27_H__ as header protector analogous to
<mach/mx...h>
- use tabs for indention
- fix sorting
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- use __MACH_IOMUX_MX25_H__ as header protector analogous to
<mach/mx...h>
- remove doxygen comments
- remove #error about mach/iomux.h which is unused on mx25
- remove #ifndef __ASSEMBLY__ which is unneeded here
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- use __MACH_IOMUX_MX21_H__ as header protector analogous to
<mach/mx...h>
- use tabs for indention
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- use __MACH_IOMUX_MX1_H__ as header protector analogous to
<mach/mx...h>
- use tabs for indention
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
While at it move register modification to static inlines and
so make the relevant code more readable.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
MXC_IRQ_PRIOR, MXC_PWM and ARCH_HAS_RNGA are all defined in an "if
ARCH_MXC" ... "endif" block, so they depend on ARCH_MXC anyhow.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This is broken since at least one year when
ec996ba (mxc timer: make compile time independent)
removed the symbol MXC_TCN.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Now if the problem occurs that triggered the BUG_ON before, the machine
runs in a NULL pointer dereference. So it wouldn't be much harder now
to debug the situation if it occured.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
As in most cases only few irqs are pending using fls is more effective
than looping over all bits.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
GPIO_INT_LOW_LEV is defined as
(cpu_is_mx1_mx2() ? 0x3 : 0x0)
so depending on compiler optimisation and enabled SoCs this doesn't
qualify as a constant expression as needed by a switch statement.
Ditto for GPIO_INT_HIGH_LEV.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This removes some #ifdefs and prepares moving the files in a directory
with more than imx21 and imx27 support.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The previous commits cleaned up arch/arm/mach-mx2/devices.c such that it
doesn't rely on deprecated symbols any more.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
As the gpio ports have different addresses on imx21 and imx27 there are
two different port descriptions needed if not relying on the overloaded
cpp macro IO_ADDRESS. So some cpp magic is added to minimize code
duplication.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The previous commit introduced one nand device per SoC. Use this
directly instead of the compatibility macro that will break for
multi-SoC kernels. And while at it remove the compatibility macro now
that all in-tree users are fixed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[Updated the device ID to -1 since there's only one IISv4 device but the
S3C clock API tries to match based on the ID of the requesting device
(and not the name) -- broonie.]
Signed-Off-by: Jassi Brar <jassi.brar@samsung.com>
[ben-linux@fluff.org: Fixed Jassi's lastname]
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch defines the platform device and the resources: IRQ, DMA and MEM,
needed by the AC97 controller driver.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The IISv4 controller is connected to the WM8580 on the board.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The PMIC LED on the SMDK6410 CPU board is driven by GPIO4 of the
WM8312 PMIC. Provide software control of this LED.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The Wolfson Microelectronics 1192-EV1 is a plug in module for the
SMDK6410 providing power using a WM8312 PMIC. This patch provides
initial hookup sufficient to initialise the board, though not all
features are fully described yet.
As part of this supplies for the system that are provided as a
single supply by one of the currently merged PMIC boards are
factored out so they can be reused between different regulators.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
GPIO_E-[5,9] pin functionality was defined incorrectly.
The patch corrects and adds missing pins.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add AC97 controller to platform devices and initialize the AC97 gpios.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Updates arch/arm Kconfig and Makefile for building the S5P6442 support.
Also modifies the plat-s5p Kconfig file to include the support for plat-s5p
for S5P6442.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds IRQ support for S5P6442. This patch adds interrupt
register definitions, IRQ definitions for various interrupt sources
and new VIC base for VIC2 in plat-s5p common irq code.
Signed-off-by: Adityapratap Sharma <aditya.ps@samsung.com>
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds clock support for S5P6442. This patch adds the clock
register definitions and the various system clocks in S5P6442.
Signed-off-by: Adityapratap Sharma <aditya.ps@samsung.com>
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds support for Samsung S5P6442 CPU. This patch also adds
an entry for S5P6442 cpu in plat-s5p cpu table.
Signed-off-by: Adityapratap Sharma <aditya.ps@samsung.com>
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
IRQ should be disabled on suspend and re-enabled on resume.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Without resources description driver fails during initialization.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
