commit ecc3ac293e upstream.
While adding the GIC ITS MSI support, it was found that the msi-map entries
needed to be swapped to receive MSIs from the endpoint.
But later it was identified that the swapping was needed due to a bug in
the Qualcomm PCIe controller driver. And since the bug is now fixed with
commit bf79e33cdd ("PCI: qcom: Enable BDF to SID translation properly"),
let's fix the msi-map entries also to reflect the actual mapping in the
hardware.
Cc: stable@vger.kernel.org # 6.3: bf79e33cdd ("PCI: qcom: Enable BDF to SID translation properly")
Fixes: ff384ab56f ("arm64: dts: qcom: sm8450: Use GIC-ITS for PCIe0 and PCIe1")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240318-pci-bdf-sid-fix-v1-1-acca6c5d9cf1@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6e115b75b4 ]
The serial ports did not have their interconnect paths specified when
they were first introduced. Fix that.
Fixes: 5188049c9b ("arm64: dts: qcom: Add base SM8450 DTSI")
Fixes: f583741847 ("arm64: dts: qcom: sm8450: add uart20 node")
Reported-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Suggested-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240116-topic-8450serial-v1-1-b685e6a5ad78@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The MCLK clocks of codec macros have fixed 19.2 MHz frequency and
assigning clock rates is redundant.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231213162856.188566-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Pin configuration for Soundwire bus should be set in Soundwire
controller nodes, not in the associated macro codec node. This
placement change should not have big impact in general, because macro
codec is a clock provider for Soundwire controller, thus its devices is
probed first. However it will have impact for disabled Soundwire buses,
e.g. WSA2, because after this change the pins will be left in default
state.
We also follow similar approach in newer SoCs, like Qualcomm SM8650.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231213162856.188566-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Qcom SoCs doesn't support the legacy PCI, but only PCIe. So use the correct
node name for the controller instances.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231206135540.17068-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The TX Soundwire controller should take clock from TX macro codec, not
VA macro codec clock, otherwise the clock stays disabled. This looks
like a copy-paste issue, because the SC8280xp code uses here correctly
clock from TX macro. The VA macro clock is already consumed by TX macro
codec, thus it won't be disabled by this change.
Fixes: 14341e76db ("arm64: dts: qcom: sm8450: add Soundwire and LPASS")
Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231129140537.161720-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The SM8450 SoC has a True Random Number Generator, add the node with
the correct compatible set.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20231003-topic-sm8550-rng-v4-5-255e4d0ba08e@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Change the PCIe QMP PHY to use newer style of QMP PHY bindings (single
resource region, no per-PHY subnodes). As a part of this conversion also
change the "refgen" name to more correct "rchng".
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-18-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Since we have those defines available in a header, let's use them
everywhere where qcom,vmid property is used.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230818-qcom-vmid-defines-v1-1-45b610c96b13@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
With the ICE driver now merged let's convert the ufs node to use the new
style.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221209-dt-binding-ufs-v5-5-c9a58c0a53f5@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The biggest change this time is for the 32-bit devicetree files, which
are all moved to a new location, using separate subdirectories for each
SoC vendor, following the same scheme that is used on arm64, mips and
riscv. This has been discussed for many years, but so far we never did
this as there was a plan to move the files out of the kernel entirely,
which has never happened.
The impact of this will be that all external patches no longer apply,
and anything depending on the location of the dtb files in the build
directory will have to change. The installed files after 'make
dtbs_install' keep the current location.
There are six added SoCs here that are largely variants of previously
added chips. Two other chips are added in a separate branch along
with their device drivers.
* The Samsung Exynos 4212 makes its return after the Samsung Galaxy
Express phone is addded at last. The SoC support was originally
added in 2012 but removed again in 2017 as it was unused at the time.
* Amlogic C3 is a Cortex-A35 based smart IP camera chip
* Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
the still common MSM8916 (Snapdragon 410) phone chip that has been
supported for a long time.
* Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
laptop chips, used in the Lenovo Flex 5G, which is added along with
the reference board.
* Qualcomm SDX75 is the latest generation modem chip that is used
as a peripherial in phones but can also run a standalone Linux. Unlike
the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.
* Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the Xuantie
C910 core, a step up from all previously added rv64 chips.
All of the above come with reference board implementations, those included
there are 39 new board files, but only five more 32-bit this time, probably
a new low:
* Marantec Maveo board based on dhcor imx6ull module
* Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip
* Epson Moverio BT-200 AR glasses based on TI OMAP4
* PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM
* ICnova ADB4006 board based on Allwinner A20
On the 64-bit side, there are also fewer addded machines than
we had in the recent releases:
* Three boards based on NXP i.MX8: Emtop SoM & Baseboard,
NXP i.MX8MM EVKB board and i.MX8MP based Gateworks Venice
gw7905-2x device.
* NVIDIA IGX Orin and Jetson Orin Nano boards, both based on
tegra234
* Qualcomm gains support for 6 reference boards on various members
of their IPQ networking SoC series, as well as the Sony Xperia M4
Aqua phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board
on top of the various reference platforms for their new chips.
* Rockchips support for several newer boards: Indiedroid Nova (rk3588),
Edgeble Neural Compute Module 6B (rk3588), FriendlyARM NanoPi R2C
Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn Fastrhino R66S/R68S
(rk3568)
* TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex Verdin
family with AM62 COM, carrier and dev boards
Other changes to existing boards contain the usual minor improvements
along with
* continued updates to clean up dts files based on dtc warnings and
binding checks, in particular cache properties and node names
* support for devicetree overlays on at91, bcm283x
* significant additions to existing SoC support on mediatek, qualcomm,
ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST STM32MP1
As usual, a lot more detail is available in the individual merge
commits.
-----BEGIN PGP SIGNATURE-----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=X/KE
-----END PGP SIGNATURE-----
Merge tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC devicetree updates from Arnd Bergmann:
"The biggest change this time is for the 32-bit devicetree files, which
are all moved to a new location, using separate subdirectories for
each SoC vendor, following the same scheme that is used on arm64, mips
and riscv. This has been discussed for many years, but so far we never
did this as there was a plan to move the files out of the kernel
entirely, which has never happened.
The impact of this will be that all external patches no longer apply,
and anything depending on the location of the dtb files in the build
directory will have to change. The installed files after 'make
dtbs_install' keep the current location.
There are six added SoCs here that are largely variants of previously
added chips. Two other chips are added in a separate branch along with
their device drivers.
- The Samsung Exynos 4212 makes its return after the Samsung Galaxy
Express phone is addded at last. The SoC support was originally
added in 2012 but removed again in 2017 as it was unused at the
time.
- Amlogic C3 is a Cortex-A35 based smart IP camera chip
- Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
the still common MSM8916 (Snapdragon 410) phone chip that has been
supported for a long time.
- Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
laptop chips, used in the Lenovo Flex 5G, which is added along with
the reference board.
- Qualcomm SDX75 is the latest generation modem chip that is used as
a peripherial in phones but can also run a standalone Linux. Unlike
the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.
- Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
Xuantie C910 core, a step up from all previously added rv64 chips.
All of the above come with reference board implementations, those
included there are 39 new board files, but only five more 32-bit this
time, probably a new low:
- Marantec Maveo board based on dhcor imx6ull module
- Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip
- Epson Moverio BT-200 AR glasses based on TI OMAP4
- PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM
- ICnova ADB4006 board based on Allwinner A20
On the 64-bit side, there are also fewer addded machines than we had
in the recent releases:
- Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.
- NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234
- Qualcomm gains support for 6 reference boards on various members of
their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
of the various reference platforms for their new chips.
- Rockchips support for several newer boards: Indiedroid Nova
(rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
Fastrhino R66S/R68S (rk3568)
- TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
Verdin family with AM62 COM, carrier and dev boards
Other changes to existing boards contain the usual minor improvements
along with
- continued updates to clean up dts files based on dtc warnings and
binding checks, in particular cache properties and node names
- support for devicetree overlays on at91, bcm283x
- significant additions to existing SoC support on mediatek,
qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
STM32MP1
As usual, a lot more detail is available in the individual merge
commits"
* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
ARM: mvebu: fix unit address on armada-390-db flash
ARM: dts: Move .dts files to vendor sub-directories
kbuild: Support flat DTBs install
ARM: dts: Add .dts files missing from the build
ARM: dts: allwinner: Use quoted #include
ARM: dts: lan966x: kontron-d10: add PHY interrupts
ARM: dts: lan966x: kontron-d10: fix SPI CS
ARM: dts: lan966x: kontron-d10: fix board reset
ARM: dts: at91: Enable device-tree overlay support for AT91 boards
arm: dts: Enable device-tree overlay support for AT91 boards
arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
ARM: dts: at91: use generic name for shutdown controller
ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
dt-bindings: firmware: brcm,kona-smc: convert to YAML
riscv: dts: sort makefile entries by directory
riscv: defconfig: enable T-HEAD SoC
MAINTAINERS: add entry for T-HEAD RISC-V SoC
riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
riscv: dts: add initial T-HEAD TH1520 SoC device tree
riscv: Add the T-HEAD SoC family Kconfig option
...
The USB HC node is missing the interconnect paths, so add them.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230602062016.1883171-6-abel.vesa@linaro.org
Add crypto engine (CE) and CE BAM related nodes and definitions
for the SM8450 SoC.
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
[Bhupesh: Corrected the compatible list]
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230526192210.3146896-12-bhupesh.sharma@linaro.org
We need more granularity for things like the GPU. Add the missing levels.
This unfortunately requires some re-indexing, resulting in an ugly diff.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230516005306.952821-1-konrad.dybcio@linaro.org
Add required cache-level and cache-unified properties to fix warnings
like:
qdu1000-idp.dtb: l3-cache: 'cache-unified' is a required property
qdu1000-idp.dtb: l2-cache: 'cache-level' is a required property
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230416101134.95686-3-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-10-krzysztof.kozlowski@linaro.org
Currently, most of the Qualcomm SoCs specify both "iommus" and "iommu-map"
properties for the PCIe nodes. First one passes the SMR mask to the iommu
driver and the latter specifies the SID for each PCIe device.
But with "iommus" property, the PCIe controller will be added to the
iommu group along with the devices. This makes no sense because the
controller will not initiate any DMA transaction on its own. And moreover,
it is not strictly required to pass the SMR mask to the iommu driver. If
the "iommus" property is not present, then the default mask of "0" would be
used which should work for all PCIe devices.
On the other side, if the SMR mask specified doesn't match the one expected
by the hypervisor, then all the PCIe transactions will end up triggering
"Unidentified Stream Fault" by the SMMU.
So to get rid of these hassles and also prohibit PCIe controllers from
adding to the iommu group, let's remove the "iommus" property from PCIe
nodes.
Reported-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-arm-msm/20230227195535.GA749409-robh@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230308075648.134119-1-manivannan.sadhasivam@linaro.org
The parent controller for both interrupts is GIC, so no need for
interrupts-extended.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230405060906.143058-5-krzysztof.kozlowski@linaro.org
Use labels, instead of comments, for Soundwire controllers. Naming them
is useful, because they are specialized and have also naming in
datasheet/programming guide.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230405060906.143058-2-krzysztof.kozlowski@linaro.org
Fixes the following DT bindings check error:
domain-idle-states: cluster-sleep-0: 'idle-state-name', 'local-timer-stop' do not match any of the regexes:
'pinctrl-[0-9]+'
domain-idle-states: cluster-sleep-1: 'idle-state-name', 'local-timer-stop' do not match any of the regexes:
'pinctrl-[0-9]+'
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323-topic-sm8450-upstream-dt-bindings-fixes-v2-2-0ca1bea1a843@linaro.org
The QMP PHY is a USB3/DP combo phy, switch to the newly
documented bindings and register the clocks to the GCC
and DISPCC controllers.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230206-topic-sm8450-upstream-dp-controller-v6-4-d78313cbc41d@linaro.org
For 1MiB of the I/O region, the I/O ports of the legacy PCI devices are
located in the range of 0x0 to 0x100000. Hence, fix the bogus PCI addresses
(0x60200000, 0x40200000) specified in the ranges property for I/O region.
While at it, let's use the missing 0x prefix for the addresses.
Fixes: bc6588bc25 ("arm64: dts: qcom: sm8450: add PCIe1 root device")
Fixes: 7b09b1b473 ("arm64: dts: qcom: sm8450: add PCIe0 RC device")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/linux-arm-msm/7c5dfa87-41df-4ba7-b0e4-72c8386402a8@app.fastmail.com/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230228164752.55682-13-manivannan.sadhasivam@linaro.org
The LLCC block has several banks each with a different base address
and holes in between. So it is not a correct approach to cover these
banks with a single offset/size. Instead, the individual bank's base
address needs to be specified in devicetree with the exact size.
Reported-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314080443.64635-11-manivannan.sadhasivam@linaro.org
Add a simple-mfd representing IMEM on SM8450 and define the PIL
relocation info region, so that post mortem tools will be able
to locate the loaded remoteprocs.
Signed-off-by: Mukesh Ojha <quic_mojha@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1677079845-17650-1-git-send-email-quic_mojha@quicinc.com
The WSA2 assigned-clocks were copied from WSA, but the WSA2 uses its
own.
Fixes: 14341e76db ("arm64: dts: qcom: sm8450: add Soundwire and LPASS")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230308123129.232642-1-krzysztof.kozlowski@linaro.org
The serial/UART device node does not have children with unit addresses,
so address/size cells are not correct.
Fixes: f583741847 ("arm64: dts: qcom: sm8450: add uart20 node")
Fixes: 5188049c9b ("arm64: dts: qcom: Add base SM8450 DTSI")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230124084951.38195-3-krzysztof.kozlowski@linaro.org
Use the correct compatible so that the driver can probe properly.
Fixes: a6dd1206e4 ("arm64: dts: qcom: sm8450: add display hardware devices")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on HDK8450
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230123200552.553181-1-konrad.dybcio@linaro.org
The devicetree should specify both MSI implementations and the OS/driver
should choose the one based on the platform requirements. Currently, Linux
DWC driver will choose GIC-ITS over the internal MSI controller.
Fixes: a11bbf6adef4 ("arm64: dts: qcom: sm8450: Use GIC-ITS for PCIe0 and PCIe1")
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230111123004.21048-2-manivannan.sadhasivam@linaro.org
Remove manually created symbol clocks and replace them with clocks
provided by PHY.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221123104443.3415267-5-dmitry.baryshkov@linaro.org
Manivannan Sadhasivam