This patch adds support for a managed device version of
adis_setup_buffer_and_trigger. It works exactly as the original
one but it calls all the devm_iio_* functions to setup an iio
buffer and trigger. Hence we do not need to care about cleaning those
and we do not need to support a remove() callback for every driver using
the adis library.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_{predisable,postenable} functions attach/detach
poll functions.
In most cases the iio_triggered_buffer_postenable() should be called first
to attach the poll function, and then the driver can init the data to be
triggered.
In this case it's the other way around: the DMA code should be initialized
before the attaching the poll function and the reverse should be done when
un-initializing.
To make things easier when removing the iio_triggered_buffer_postenable() &
iio_triggered_buffer_predisable() functions from the IIO core API, the DMA
code has been moved into preenable() for init, and postdisable() for
uninit.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change moves the logic to check if the current channel is the
touchscreen channel to a separate helper.
This reduces some code duplication, but the main intent is to re-use this
in the next patches.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change will allow the at91-sama5d2_adc driver to use other triggers
than it's own.
In particular, tested with the sysfs trigger.
To be able to achieve this functionality, some changes were required:
1) Do not enable/disable channels when enabling/disabling the trigger.
This is because the trigger is enabled/disabled only for our trigger
(obviously). We need channels enabled/disabled regardless of what trigger is
being used.
2) Cope with DMA : DMA cannot be used when using another type of trigger.
Other triggers work through pollfunc, so we get polled anyway on every trigger.
Thus we have to obtain data at every trigger.
3) When to start conversion? The usual pollfunc (store time from subsystem)
would be in hard irq and this would be a good way, but current iio subsystem
recommends to have it in the threaded irq. Thus adding software start
code in this handler.
4) Buffer config: we need to setup buffer regardless of our own device's
trigger. We may get one attached later.
5) IRQ handling: we use our own device IRQ only if it's our own trigger
and we do not use DMA . If we use DMA, we use the DMA controller's IRQ.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It can happen that on IRQ trigger, not all conversions are done if
we are enabling multiple channels.
The IRQ is triggered on first EOC (end of channel), but it can happen
that not all channels are done. This leads into erroneous reports to
userspace (zero values or previous values).
To solve this, in trigger handler, check if the mask of done channels
is the same as the mask of active scan channels.
If it's the same, proceed and push to buffers. Otherwise, use usleep
to sleep until the conversion is done or we timeout.
Normally, it should happen that in a short time fashion, all channels are
ready, since the first IRQ triggered.
If a hardware fault happens (for example the clock suddently dissappears),
the handler will not be completed, in which case we do not report anything to
userspace anymore.
Also, change from using the EOC interrupts to DRDY interrupt.
This helps with the fact that not 'n' interrupt statuses are enabled,
each being able to trigger an interrupt, and instead only data ready
interrupt can wake up the CPU. Like this, when data is ready, check in
handler which and how many channels are done. While the DRDY is raised,
other IRQs cannot occur. Once the channel data is being read, we ack the
IRQ and finish the conversion.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enables probing via ACPI PRP0001 route and removes an example of
an approach we no longer want people to copy.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Enables probing via ACPI PRP0001 and removes an example that we don't
want people to cut and paste into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Enables probing via ACPI PRP0001 but mostly about removing examples
that might be copied to new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Also drops ifdef protections for CONFIG_OF.
Enables probing via ACPI PRP0001 and removes an example that might be
cut and paste into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Enables ACPI probing via PRP0001 and removes an example that might
be cut and paste to a new driver.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Enables probing via the ACPI PRP0001 route but more is mosty about
removing examples of this that might get copied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Whilst this enables ACPI binding or the device via PRP0001 the
primary aim is to remove potential for these two things to be
cut and paste into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Enables ACPI DSDT to probe via PRP0001 and the compatible property. Also
removes the ifdef protections for CONFIG_OF.
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enables ACPI DSDT to probe via PRP0001 and the compatible property.
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Atlas Scientific RTD-SM OEM sensor reads temperature using
resistance temperature detector technology.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
IIO_CONCENTRATION channel for the DO-SM shouldn't be indexed as
there isn't more than one, and also ATLAS_CONCENTRATION_CHANNEL
macro scan_index define steps on the IIO_TIMESTAMP channel.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Fixes: a751b8e480 (iio: chemical: atlas-sensor: add DO-SM module support)
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Usual mix of new drivers, new support in old drivers and lots of minor
cleanup. Yaml conversions also continue to trickle in (plenty more to go!)
New device support
* ad7476
- Add ad7091 support (ID only)
* ad9467
- New driver for this 200/250 MSPS adi-axi-adc and SPI attached ADC.
* adi-axi-adc
- New driver to support ADIs generic AXI ADC IP core, used to provide
high speed interfaces to ADCs (JESD204B/C or parallel interfaces). Usually
paired with a device using a slow configuration interface (spi etc)
Includes DT bindings and some fixes for fpga headers.
* bmg160
- Add support for BMI088 (ID only)
* max1241
- New driver for this ADC.
* st_sensors
- Add support for LIS2HH12 accelerometer
* sx9310
- New driver supporting sx9310 and sx9311 proximity sensors.
Yaml DT binding conversions
* rockchip-saradc (including adding some missing parts)
* stm32-dac
* tsl2563
* vcnl4000
Features
* st_lsm6dsx
- Add LIS3MDL as a possible sensor hub device.
* vcnl4000
- Add new concept of near level (from DT) to provide to userspace which
often needs to have some calibrated concept of 'near'.
Cleanups, minor fixes etc.
* core
- Use snprintf for functions where strings are built and there is
potential for overflow.
- Correct docs to indicate mlock should not be used directly by drivers.
- Fix up accidental dropping of a patch to use bitmap_zalloc.
- Stop allowing enabling of buffers with no channels enabled.
- Drop unused 'stufftoread' from iio_buffer.
- Drop scan_el_attrs form iio_buffer as unused.
- Reorder sanity checks in __iio_device_register to fail earlier.
- Drop all the devm_ runregister / free functions from IIO as they
were never used and encourage poor design.
* dma-buffer
- Tidy up includes.
* dma-engine-buffer
- Provide dev-managed allocator.
- Fix an issue with printing a size_t
* cross subsystem (kxsd9, bmg160, mpu3050, bmi160, mpu6050, bmc150)
- Replace some unnecessary casts of error ptrs and whilst there.
use the %pe printf parameter to print them in a more useful fashion.
* cross subsystem
- Drop casts in calls to regmap_bulk_read as they make no sense.
- Use devm_platform_ioremap_resource to reduce boilerplate.
- Fix typos in Analog Devices.
* counters/104-quad
- Add Syed Nayyar Waris as an additional maintainer.
* ad7476
- Generate CONVST signal internally rather than requiring external
trigger. Add sysfs read back as can now do so.
- use devm_add_action_or_reset to tidy up error and remove handling.
* ad7793
- Switch to read_avail from explicit attribute. Mostly done to avoid
confusing people with a - sign (without surounding spaces) that
was correct but checkpatch didn't like.
* adis library
- Add missing newlines at end of error messages.
* adis16400
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* adis16460
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* ad_sigma_delta
- Move some channel definitions into individual drivers to avoid
having to deal with complex options.
* ak8974
- Silence an error on deffered probe.
* bmp280
- Harden against IRQ before registration.
- Convert to read_avail instead of opencoding the equivalent.
- Explicitly mark GPIO as optional.
- Cleanup casts.
- Remove line breaks from strings.
* htts221
- Replace direct access to platform_data with dev_get_platdata().
- Use device properties rather than device tree ones to allow ACPI
probing.
- Casting cleanups.
* intel_mrfld_adc
- Don't use unaligned accessor for aligned data.
* isl29125
- Reorder buer pre and post hooks to allow for coming core rework.
* ltc2983
- Remove comp to bool.
* max1363
- Stop using mlock from the iio_dev directly in favour of a local lock
with clearly defined scope.
* max30100
- Use generic device properties to allow ACPI probe.
* mpu6050
- Convert to i2c_new_client_device.
- Add debugfs register access.
* st_lsm6dsx
- Provide means of configuring full scale on slave device if supported.
- Drop include of st_sensors header to get one value. Its not otherwise
used by this driver.
* st-sensors
- Replace direct access to platform_data with dev_get_platdata().
- Casting cleanups.
- Avoid splitting strings.
* st_uvis25
- Casting cleanups.
* tsl2563
- Typo fix.
* tsl2772
- scnprintf in a non obvious string building usecase. Note also 'fixes'
a wrong calculation of remaining space that couldn't actually cause
any trouble as there was lots of room.
* xilinx-xadc
- Fix Lars-Peter spelling his own name wrong :) + additional typos.
-----BEGIN PGP SIGNATURE-----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=DyTF
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.8a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new IIO device support, features and cleanup for the 5.8 cycle
Usual mix of new drivers, new support in old drivers and lots of minor
cleanup. Yaml conversions also continue to trickle in (plenty more to go!)
New device support
* ad7476
- Add ad7091 support (ID only)
* ad9467
- New driver for this 200/250 MSPS adi-axi-adc and SPI attached ADC.
* adi-axi-adc
- New driver to support ADIs generic AXI ADC IP core, used to provide
high speed interfaces to ADCs (JESD204B/C or parallel interfaces). Usually
paired with a device using a slow configuration interface (spi etc)
Includes DT bindings and some fixes for fpga headers.
* bmg160
- Add support for BMI088 (ID only)
* max1241
- New driver for this ADC.
* st_sensors
- Add support for LIS2HH12 accelerometer
* sx9310
- New driver supporting sx9310 and sx9311 proximity sensors.
Yaml DT binding conversions
* rockchip-saradc (including adding some missing parts)
* stm32-dac
* tsl2563
* vcnl4000
Features
* st_lsm6dsx
- Add LIS3MDL as a possible sensor hub device.
* vcnl4000
- Add new concept of near level (from DT) to provide to userspace which
often needs to have some calibrated concept of 'near'.
Cleanups, minor fixes etc.
* core
- Use snprintf for functions where strings are built and there is
potential for overflow.
- Correct docs to indicate mlock should not be used directly by drivers.
- Fix up accidental dropping of a patch to use bitmap_zalloc.
- Stop allowing enabling of buffers with no channels enabled.
- Drop unused 'stufftoread' from iio_buffer.
- Drop scan_el_attrs form iio_buffer as unused.
- Reorder sanity checks in __iio_device_register to fail earlier.
- Drop all the devm_ runregister / free functions from IIO as they
were never used and encourage poor design.
* dma-buffer
- Tidy up includes.
* dma-engine-buffer
- Provide dev-managed allocator.
- Fix an issue with printing a size_t
* cross subsystem (kxsd9, bmg160, mpu3050, bmi160, mpu6050, bmc150)
- Replace some unnecessary casts of error ptrs and whilst there.
use the %pe printf parameter to print them in a more useful fashion.
* cross subsystem
- Drop casts in calls to regmap_bulk_read as they make no sense.
- Use devm_platform_ioremap_resource to reduce boilerplate.
- Fix typos in Analog Devices.
* counters/104-quad
- Add Syed Nayyar Waris as an additional maintainer.
* ad7476
- Generate CONVST signal internally rather than requiring external
trigger. Add sysfs read back as can now do so.
- use devm_add_action_or_reset to tidy up error and remove handling.
* ad7793
- Switch to read_avail from explicit attribute. Mostly done to avoid
confusing people with a - sign (without surounding spaces) that
was correct but checkpatch didn't like.
* adis library
- Add missing newlines at end of error messages.
* adis16400
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* adis16460
- Use DEFINE_DEBUGS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTR.
* ad_sigma_delta
- Move some channel definitions into individual drivers to avoid
having to deal with complex options.
* ak8974
- Silence an error on deffered probe.
* bmp280
- Harden against IRQ before registration.
- Convert to read_avail instead of opencoding the equivalent.
- Explicitly mark GPIO as optional.
- Cleanup casts.
- Remove line breaks from strings.
* htts221
- Replace direct access to platform_data with dev_get_platdata().
- Use device properties rather than device tree ones to allow ACPI
probing.
- Casting cleanups.
* intel_mrfld_adc
- Don't use unaligned accessor for aligned data.
* isl29125
- Reorder buer pre and post hooks to allow for coming core rework.
* ltc2983
- Remove comp to bool.
* max1363
- Stop using mlock from the iio_dev directly in favour of a local lock
with clearly defined scope.
* max30100
- Use generic device properties to allow ACPI probe.
* mpu6050
- Convert to i2c_new_client_device.
- Add debugfs register access.
* st_lsm6dsx
- Provide means of configuring full scale on slave device if supported.
- Drop include of st_sensors header to get one value. Its not otherwise
used by this driver.
* st-sensors
- Replace direct access to platform_data with dev_get_platdata().
- Casting cleanups.
- Avoid splitting strings.
* st_uvis25
- Casting cleanups.
* tsl2563
- Typo fix.
* tsl2772
- scnprintf in a non obvious string building usecase. Note also 'fixes'
a wrong calculation of remaining space that couldn't actually cause
any trouble as there was lots of room.
* xilinx-xadc
- Fix Lars-Peter spelling his own name wrong :) + additional typos.
* tag 'iio-for-5.8a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (101 commits)
iio: magnetometer: ak8974: Silence deferred-probe error
Documentation: ABI: document IIO in_proximity_nearlevel file
iio: vcnl4000: Export near level property for proximity sensor
dt-bindings: iio: light: vcnl4000: Add proximity-near-level
dt-bindings: iio: Introduce common properties for iio sensors
dt-bindings: iio: vcnl4000: convert bindings to YAML format
iio: Fix misspellings of "Analog Devices"
iio: light: isl29125: fix iio_triggered_buffer_{predisable,postenable} positions
iio: adc: fsl-imx25-gcq: Use devm_platform_ioremap_resource
iio: adc: at91-adc: Use devm_platform_ioremap_resource
iio: adc: sun4i-gpadc-iio: Use devm_platform_ioremap_resource
iio:light:ltr501: Drop unnecessary cast of parameter in regmap_bulk_read
iio:magn:mmc35240: Drop unnecessary casts of val parameter in regmap_bulk*
iio:imu:mpu6050: Tidy up parameters to regmap_bulk functions.
iio:chemical:bme680: Tidy up parameters to regmap_bulk_read
iio:chemical:atlas-sensor: Drop unnecessary explicit casts in regmap_bulk_read calls
iio:accel:mxc4005: Drop unnecessary explicit casts in regmap_bulk_read calls
iio: imu: st_lsm6dsx: drop huge include in sensor-hub driver
iio: buffer: drop devm_iio_kfifo_free() API call
iio: buffer: drop devm_iio_hw_consumer_free() API call
...
Includes one MAINTAINERS update to avoid people getting a lot of bounce
messages and complaining about it.
* MAINTAINERS
- Drop Stefan Popa's Analog Devices email address in favour of
Michael Hennerich.
* core
- Fix handling of dB sysfs inputs.
- Drop a stray semi colon in macro definition.
* ad5770r
- Fix an off by one in chec on maximum number of channels.
* ad7192
- Fix a null pointer de-reference due to the name previously being
retrieved from the spi_get_device_id call which no longer works as
the relevant table was removed.
* ad7797
- Use correct attribute group.
* counter/104-quad-8
- Add locks to prevent some race conditions.
* inv-mpu6050
- Fix issues around suspend / resume clashing with runtime PM.
* stm32-adc
- Fix sleep in invalid context
- Fix id relative path error in device tree binding doc.
* st_lsm6dsx
- Fix a read alignment issue on an untagged FIFO.
- Handle odr for slave to properly compute the FIFO data layout / pattern.
- Flush the HW FIFO before resettting the device to avoid a race on
interrupt line 1.
* st_sensors
- Rely on ODR mask not ODR address to identify if the ODR can be set.
Some devices have an ODR address of 0.
* ti-ads8344
- Byte ordering was wrong - fix it.
* xilinx-xadc
- Fix inverted logic in powering down the second ADC.
- Fix clearing interrupt when enabling the trigger.
- Fix configuration of sequencer when in simultaneous sampling mode.
- Limit initial sampling rate as done for runtime configured ones.
-----BEGIN PGP SIGNATURE-----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=SmJy
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 5.7 cycle.
Includes one MAINTAINERS update to avoid people getting a lot of bounce
messages and complaining about it.
* MAINTAINERS
- Drop Stefan Popa's Analog Devices email address in favour of
Michael Hennerich.
* core
- Fix handling of dB sysfs inputs.
- Drop a stray semi colon in macro definition.
* ad5770r
- Fix an off by one in chec on maximum number of channels.
* ad7192
- Fix a null pointer de-reference due to the name previously being
retrieved from the spi_get_device_id call which no longer works as
the relevant table was removed.
* ad7797
- Use correct attribute group.
* counter/104-quad-8
- Add locks to prevent some race conditions.
* inv-mpu6050
- Fix issues around suspend / resume clashing with runtime PM.
* stm32-adc
- Fix sleep in invalid context
- Fix id relative path error in device tree binding doc.
* st_lsm6dsx
- Fix a read alignment issue on an untagged FIFO.
- Handle odr for slave to properly compute the FIFO data layout / pattern.
- Flush the HW FIFO before resettting the device to avoid a race on
interrupt line 1.
* st_sensors
- Rely on ODR mask not ODR address to identify if the ODR can be set.
Some devices have an ODR address of 0.
* ti-ads8344
- Byte ordering was wrong - fix it.
* xilinx-xadc
- Fix inverted logic in powering down the second ADC.
- Fix clearing interrupt when enabling the trigger.
- Fix configuration of sequencer when in simultaneous sampling mode.
- Limit initial sampling rate as done for runtime configured ones.
* tag 'iio-fixes-for-5.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
MAINTAINERS: remove Stefan Popa's email
iio: adc: ad7192: fix null pointer de-reference crash during probe
iio: core: remove extra semi-colon from devm_iio_device_register() macro
iio: adc: ti-ads8344: properly byte swap value
iio: imu: inv_mpu6050: fix suspend/resume with runtime power
iio: st_sensors: rely on odr mask to know if odr can be set
iio: xilinx-xadc: Make sure not exceed maximum samplerate
iio: xilinx-xadc: Fix sequencer configuration for aux channels in simultaneous mode
iio: xilinx-xadc: Fix clearing interrupt when enabling trigger
iio: xilinx-xadc: Fix ADC-B powerdown
iio: dac: ad5770r: fix off-by-one check on maximum number of channels
iio: imu: st_lsm6dsx: flush hw FIFO before resetting the device
iio: core: Fix handling of 'dB'
dt-bindings: iio: adc: stm32-adc: fix id relative path
counter: 104-quad-8: Add lock guards - generic interface
iio: imu: st_lsm6dsx: specify slave odr in slv_odr
iio: imu: st_lsm6dsx: fix read misalignment on untagged FIFO
iio: adc: stm32-adc: fix sleep in atomic context
iio:ad7797: Use correct attribute_group
When the 'spi_device_id' table was removed, it omitted to cleanup/fix the
assignment:
'indio_dev->name = spi_get_device_id(spi)->name;'
After that patch 'spi_get_device_id(spi)' returns NULL, so this crashes
during probe with null de-ref.
This change fixes this by introducing an ad7192_chip_info struct, and
defines all part-names [that should be assigned to indio_dev->name] in a
'ad7192_chip_info_tbl' table.
With this change, the old 'st->devid' is also moved to be a
'chip_info->chip_id'. And the old 'ID_AD719X' macros have been renamed to
'CHIPID_AD719X'. Tld identifiers have been re-purposed to be enum/index
values in the new 'ad7192_chip_info_tbl'.
This should fix the bug, and maintain the ABI for the 'indio_dev->name'
field.
Fixes: 66614ab2be ("staging: iio: adc: ad7192: removed spi_device_id")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The first received byte is the MSB, followed by the LSB so the value needs
to be byte swapped.
Also, the ADC actually has a delay of one clock on the SPI bus. Read three
bytes to get the last bit.
Fixes: 8dd2d7c0fe ("iio: adc: Add driver for the TI ADS8344 A/DC chips")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Suspend/resume were not working correctly with pm runtime.
Now suspend check if the chip is already suspended, and
resume put runtime pm in the correct state.
Issues seen prior to this were:
When entering suspend, there was an error in logs because we
were disabling vddio regulator although it was already disabled.
And when resuming, the chip was pull back to full power but the
pm_runtime state was not updated. So it was believing it was
still suspended.
Fixes: 4599cac846 ("iio: imu: inv_mpu6050: use runtime pm with autosuspend")
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Indeed, relying on addr being not 0 cannot work because some device have
their register to set odr at address 0. As a matter of fact, if the odr
can be set, then there is a mask.
Sensors with ODR register at address 0 are: lsm303dlh, lsm303dlhc, lsm303dlm
Fixes: 7d24517267 ("iio: common: st_sensors: check odr address value in st_sensors_set_odr()")
Signed-off-by: Lary Gibaud <yarl-baudig@mailoo.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The XADC supports a samplerate of up to 1MSPS. Unfortunately the hardware
does not have a FIFO, which means it generates an interrupt for each
conversion sequence. At one 1MSPS this creates an interrupt storm that
causes the system to soft-lock.
For this reason the driver limits the maximum samplerate to 150kSPS.
Currently this check is only done when setting a new samplerate. But it is
also possible that the initial samplerate configured in the FPGA bitstream
exceeds the limit.
In this case when starting to capture data without first changing the
samplerate the system can overload.
To prevent this check the currently configured samplerate in the probe
function and reduce it to the maximum if necessary.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The XADC has two internal ADCs. Depending on the mode it is operating in
either one or both of them are used. The device manual calls this
continuous (one ADC) and simultaneous (both ADCs) mode.
The meaning of the sequencing register for the aux channels changes
depending on the mode.
In continuous mode each bit corresponds to one of the 16 aux channels. And
the single ADC will convert them one by one in order.
In simultaneous mode the aux channels are split into two groups the first 8
channels are assigned to the first ADC and the other 8 channels to the
second ADC. The upper 8 bits of the sequencing register are unused and the
lower 8 bits control both ADCs. This means a bit needs to be set if either
the corresponding channel from the first group or the second group (or
both) are set.
Currently the driver does not have the special handling required for
simultaneous mode. Add it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When enabling the trigger and unmasking the end-of-sequence (EOS) interrupt
the EOS interrupt should be cleared from the status register. Otherwise it
is possible that it was still set from a previous capture. If that is the
case the interrupt would fire immediately even though no conversion has
been done yet and stale data is being read from the device.
The old code only clears the interrupt if the interrupt was previously
unmasked. Which does not make much sense since the interrupt is always
masked at this point and in addition masking the interrupt does not clear
the interrupt from the status register. So the clearing needs to be done
unconditionally.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The check for shutting down the second ADC is inverted. This causes it to
be powered down when it should be enabled. As a result channels that are
supposed to be handled by the second ADC return invalid conversion results.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently there is an off-by-one check on the number of channels that
will cause an arry overrun in array st->output_mode when calling the
function d5770r_store_output_range. Fix this by using >= rather than >
to check for maximum number of channels.
Addresses-Coverity: ("Out-of-bounds access")
Fixes: cbbb819837 ("iio: dac: ad5770r: Add AD5770R support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
flush hw FIFO before device reset in order to avoid possible races
on interrupt line 1. If the first interrupt line is asserted during
hw reset the device will work in I3C-only mode (if it is supported)
Fixes: 801a6e0af0 ("iio: imu: st_lsm6dsx: add support to LSM6DSO")
Fixes: 43901008fd ("iio: imu: st_lsm6dsx: add support to LSM6DSR")
Reported-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Vitor Soares <vitor.soares@synopsys.com>
Tested-by: Vitor Soares <vitor.soares@synopsys.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch fixes the call to iio_str_to_fixpoint when using 'dB' sufix.
Before this the scale_db was not used when parsing the string written to
the attribute and it failed with invalid value.
Fixes: b852822474 ("iio: core: Handle 'dB' suffix in core")
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's not uncommon that voltage regulator becomes available later during
kernel's boot process. This patch adds info message about unavailable
regulators in a case of the deferred-probe error and also amends the
error message with a error code.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When an object can be considered close to the sensor is hardware
dependent. Allowing to configure the property via device tree
allows to configure this device specific value.
This is useful for e.g. iio-sensor-proxy to indicate to userspace
if an object is close to the sensor.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to https://www.analog.com/, the company name is spelled
"Analog Devices".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_{predisable,postenable} functions attach/detach
the poll functions.
For the predisable hook, the disable code should occur before detaching
the poll func, and for the postenable hook, the poll func should be
attached before the enable code.
This change reworks the predisable/postenable hooks so that the pollfunc is
attached/detached in the correct position.
It also balances the calls a bit, by grouping the preenable and the
iio_triggered_buffer_postenable() into a single
isl29125_buffer_postenable() function.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the helper function that wraps the calls to
platform_get_resource() and devm_ioremap_resource()
together. It reduces boilerplate and suggested by coccinelle.
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the helper function that wraps the calls to
platform_get_resource() and devm_ioremap_resource()
together. It reduces boilerplate and suggested by coccinelle.
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the helper function that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together. Reduces boilerplate and suggested
by coccinelle.
Signed-off-by: Aishwarya Ramakrishnan <aishwaryarj100@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This only occurs once in the driver and isn't needed in this case either,
so drop it.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Given the parameter is void *, casting to u8 * is unnecessary.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
A mixture of:
* Casts to u8 * for the val parameter which is void * and so needs no cast.
* Explicit sizes when we can use sizeof on the destination / source variable.
Not broken in anyway, I'm just trying to tidy up the is in the subsystem to
avoid it getting cut and paste into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
A mixture of:
* Unnecessary casts of val parameter to u8 * which makes little sense as
the function take a void *.
* Explicit sizes where we can use the destination type to define that.
Note that's not true in all cases as we do read 3 bytes into 4 byte
destinations.
Note that noting was broken here, I'm just trying to ensure this doesn't
get cut and paste into more drivers so cleaning these out subsystem wide.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Himanshu Jha <himanshujha199640@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
regmap_bulk_read takes a void * for its val parameter. It certainly
makes no sense to cast to a (u8 *) + no need to explicitly cast
at all when converting another pointer type to void *.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
regmap_bulk_read takes a void * for its val parameter. It certainly
makes no sense to cast to a (u8 *) + no need to explicitly cast
at all when converting another pointer type to void *.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
st_lsm6dsx is a standalone driver for STM IMU sensors and does not rely
on st_sensor common framework, so it does not include st_sensor common
definitions.
In st_lsm6dsx_shub driver st_sensors.h is used just to introduce the
default wai address for LIS3MDL sensor.
Drop this largely unconnected include file and introduce the default wai
address for LIS3MDL in st_lsm6dsx_ext_dev_settings register map
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
This is the last user of 'devm_iio_device_match()', so it can be removed as
well in this patch.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's unused so far, so it can be removed. Also makes sense to remove it
to discourage weird uses of this call during review.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Moves this to be the first check, as it's very simple and fails the
registration earlier, instead of potentially initializing the
'indio_dev->label' and checking for duplicate indexes, and then failing
with this simple-check.
This is a minor optimization, since '__iio_device_register()' will waste
fewer validation cycles in case 'indio_dev->info' is NULL.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This field doesn't seem used. It seems that only 'buffer->attrs' was ever
used to extend sysfs attributes for an IIO buffer.
Moving forward, it may not make sense to keep it. This patch removes the
field and it's initialization code.
Since we want to rework IIO buffer, to be able to add more buffers per IIO
device, we will merge [somehow] the 'buffer' & 'scan_elements' groups, and
we will continue to add the attributes to the 'buffer' group.
Removing it here, will also make the rework here a bit smaller, since
this code will not be present.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'.
Fixes: 1fd4567026 ("iio: imu: adis: add support product ID check in adis_initial_startup")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix a typo. 'at the a time' -> 'at a time'.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO DMA buffer is a DMA buffer implementation. As such it should
include buffer_impl.h rather than buffer.h.
The include to buffer.h in buffer-dma.h should be buffer_impl.h so it has
access to the struct iio_buffer definition. The code currently only works
because all places that use buffer-dma.h include buffer_impl.h before it.
The include to buffer.h in industrialio-buffer-dma.c can be removed since
those file does not reference any of buffer consumer functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add driver for the Maxim MAX1241 12-bit, single-channel ADC.
Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX1240-MAX1241.pdf
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Alexandru Lazar <alazar@startmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for STMicroelectronics LISHH12 accelerometer in st_accel
framework.
https://www.st.com/resource/en/datasheet/lis2hh12.pdf
Signed-off-by: Gaëtan André <rvlander@gaetanandre.eu>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add LIS3MDL register map to sensor hub device table.
Tested with LSM6DSM.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Support for sensor with up to 8 different ODR settings.
Required for supporting LIS3MDL as sensor hub slave device.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
debugfs_create_file_unsafe does not protect the fops handed to it
against file removal. DEFINE_DEBUGFS_ATTRIBUTE makes the fops aware of
the file lifetime and thus protects it against removal.
Signed-off-by: Rohit Sarkar <rohitsarkar5398@gmail.com>
Tested-by Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
debugfs_create_file_unsafe does not protect the fops handed to it
against file removal. DEFINE_DEBUGFS_ATTRIBUTE makes the fops aware of
the file lifetime and thus protects it against removal.
Signed-off-by: Rohit Sarkar <rohitsarkar5398@gmail.com>
Tested-by Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce st_lsm6dsx_shub_set_full_scale routine in order to configure
the i2c slave device sensitivity
Tested-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD9467 is a 16-bit, monolithic, IF sampling analog-to-digital converter
(ADC). It is optimized for high performanceover wide bandwidths and ease of
use. The product operates at a 250 MSPS conversion rate and is designed for
wireless receivers, instrumentation, and test equipment that require a high
dynamic range. The ADC requires 1.8 V and 3.3 V power supplies and a low
voltage differential input clock for full performance operation. No
external reference or driver components are required for many applications.
Data outputs are LVDS compatible (ANSI-644 compatible) and include the
means to reduce the overall current needed for short trace distances.
Since the chip can operate at such high sample-rates (much higher than
classical interfaces), it requires that a DMA controller be used to
interface directly to the chip and push data into memory.
Typically, the AXI ADC IP core is used to interface with it.
Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/AD9467.pdf
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change adds support for the Analog Devices Generic AXI ADC IP core.
The IP core is used for interfacing with analog-to-digital (ADC) converters
that require either a high-speed serial interface (JESD204B/C) or a source
synchronous parallel interface (LVDS/CMOS).
Usually, some other interface type (i.e SPI) is used as a control interface
for the actual ADC, while the IP core (controlled via this driver), will
interface to the data-lines of the ADC and handle the streaming of data
into memory via DMA.
Because of this, the AXI ADC driver needs the other SPI-ADC driver to
register with it. The SPI-ADC needs to be register via the SPI framework,
while the AXI ADC registers as a platform driver. The two cannot be ordered
in a hierarchy as both drivers have their own registers, and trying to
organize this [in a hierarchy becomes] problematic when trying to map
memory/registers.
There are some modes where the AXI ADC can operate as standalone ADC, but
those will be implemented at a later point in time.
DocLink: https://wiki.analog.com/resources/fpga/docs/axi_adc_ip
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, when using a 'iio_dmaengine_buffer_alloc()', an matching call to
'iio_dmaengine_buffer_free()' must be made.
With this change, this can be avoided by using
'devm_iio_dmaengine_buffer_alloc()'. The buffer will get free'd via the
device's devres handling.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The 'size_t' type behaves differently on 64-bit architectures, and causes
compiler a warning of the sort "format '%u' expects argument of type
'unsigned int', but argument 3 has type 'size_t {aka long unsigned int}'".
This change adds the correct specifier for the 'align' field.
Fixes: 4538c18568 ("iio: buffer-dmaengine: Report buffer length requirements")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The debugfs interface provides direct access to read and write device
registers if debugfs is enabled.
Signed-off-by: Rohit Sarkar <rohitsarkar5398@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
For easy grepping on debug purposes join string literals back in
the messages.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In few places the unnecessary explicit castings are being used.
Drop them for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Show by using a corresponding API call that GPIO is optional.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert to use ->read_avail() instead of open-coded attribute handling.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With DEBUG_SHIRQ enabled we have a kernel crash
[ 116.482696] BUG: kernel NULL pointer dereference, address: 0000000000000000
...
[ 116.606571] Call Trace:
[ 116.609023] <IRQ>
[ 116.611047] complete+0x34/0x50
[ 116.614206] bmp085_eoc_irq+0x9/0x10 [bmp280]
because DEBUG_SHIRQ mechanism fires an IRQ before registration and drivers
ought to be able to handle an interrupt happening before request_irq() returns.
Fixes: aae9539496 ("iio: pressure: bmp280: add support for BMP085 EOC interrupt")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move away from the deprecated API and return the shiny new ERRPTR where
useful.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Utilize %pe format specifier from vsprintf while printing error logs
with dev_err(). Discards the use of unnecessary explicit casting and
prints symbolic error name which might prove to be convenient during
debugging.
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Utilize %pe format specifier from vsprintf while printing error logs
with dev_err(). Discards the use of unnecessary explicit casting and
prints symbolic error name which might prove to be convenient during
debugging.
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Utilize %pe format specifier from vsprintf while printing error logs
with dev_err(). Discards the use of unnecessary explicit casting and
prints symbolic error name which might prove to be convenient during
debugging.
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Utilize %pe format specifier from vsprintf while printing error logs
with dev_err(). Discards the use of unnecessary explicit casting and
prints symbolic error name which might prove to be convenient during
debugging.
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Utilize %pe format specifier from vsprintf while printing error logs
with dev_err(). Discards the use of unnecessary explicit casting and
prints symbolic error name which might prove to be convenient during
debugging.
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Utilize %pe format specifier from vsprintf while printing error logs
with dev_err(). Discards the use of unnecessary explicit casting and
prints symbolic error name which might prove to be convenient during
debugging.
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Utilize %pe format specifier from vsprintf while printing error logs
with dev_err(). Discards the use of unnecessary explicit casting and
prints symbolic error name which might prove to be convenient during
debugging.
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Utilize %pe format specifier from vsprintf while printing error logs
with dev_err(). Discards the use of unnecessary explicit casting and
prints symbolic error name which might prove to be convenient during
debugging.
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Utilize %pe format specifier from vsprintf while printing error logs
with dev_err(). Discards the use of unnecessary explicit casting and
prints symbolic error name which might prove to be convenient during
debugging.
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change uses the read_avail and '.info_mask_shared_by_type_available'
modifier to set the available scale.
Essentially, nothing changes to the driver's ABI.
The main idea for this patch is to remove the AD7793 driver from
checkpatch's radar. There have been about ~3 attempts to fix/break the
'in_voltage-voltage_scale_available' attribute, because checkpatch assumed
it to be an arithmetic operation and people were trying to change that.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Before activating a buffer make sure that at least one channel is enabled.
Activating a buffer with 0 channels enabled doesn't make too much sense and
disallowing this case makes sure that individual driver don't have to add
special case code to handle it.
Currently, without this patch enabling a buffer is possible and no error is
produced. With this patch -EINVAL is returned.
An example of execution with this patch and some instrumented print-code:
root@analog:~# cd /sys/bus/iio/devices/iio\:device3/buffer
root@analog:/sys/bus/iio/devices/iio:device3/buffer# echo 1 > enable
0: iio_verify_update 748 indio_dev->masklength 2 *insert_buffer->scan_mask 00000000
1: iio_verify_update 753
2:__iio_update_buffers 1115 ret -22
3: iio_buffer_store_enable 1241 ret -22
-bash: echo: write error: Invalid argument
1, 2 & 3 are exit-error paths. 0 the first print in iio_verify_update()
rergardless of error path.
Without this patch (and same instrumented print-code):
root@analog:~# cd /sys/bus/iio/devices/iio\:device3/buffer
root@analog:/sys/bus/iio/devices/iio:device3/buffer# echo 1 > enable
0: iio_verify_update 748 indio_dev->masklength 2 *insert_buffer->scan_mask 00000000
root@analog:/sys/bus/iio/devices/iio:device3/buffer#
Buffer is enabled with no error.
Note from Jonathan: Probably not suitable for automatic application to stable.
This has been there from the very start. It tidies up an odd corner
case but won't effect any 'real' users.
Fixes: 84b36ce5f7 ("staging:iio: Add support for multiple buffers")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
snprintf() is a hard-to-use function, it's especially difficult to use
it for concatenating substrings in a buffer with a limited size.
Since snprintf() returns the would-be-output size, not the actual
size, the subsequent use of snprintf() may go beyond the given limit
easily. Although the current code doesn't actually overflow the
buffer, it's an incorrect usage.
This patch replaces such snprintf() calls with a safer version,
scnprintf().
Also this fixes the incorrect argument of the buffer limit size passed
to snprintf(), too. The size has to be decremented for the remaining
length.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace usage indio_dev's mlock with either local lock or
iio_device_claim_direct_mode.
Signed-off-by: Rohit Sarkar <rohitsarkar5398@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of of_property_read_xxx use device_property_read_xxx as it is
compatible with ACPI too as opposed to only device tree.
Signed-off-by: Rohit Sarkar <rohitsarkar5398@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The BMI088 is pin-compatible with the BMI055, and provides
both gyro and accel functions. The gyro part is similar to
the BMI055 and this adds the chip to the list of supported
devices for the gyro part.
The accel part of the chip is not compatible with anything
existing already.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 3862828a90 ("iio: buffer: Switch to bitmap_zalloc()") introduced
bitmap_alloc(), but commit 20ea39ef9f ("iio: Fix scan mask selection")
reverted it.
This change adds it back. The only difference is that it's adding
bitmap_zalloc(). There might be some changes later that would require
initializing it to zero. In any case, now it's already zero-ing the
trialmask.
Appears to have been the result of merge conflict resolution rather
than an intentional revert.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver seems to use most of the AD_SD_*_CHANNEL. This change will move
them in the driver. The intent is that if a new part comes along which
would require tweaks per IIO channel, these should be doable in the driver.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver seems to use most of the AD_SD_*_CHANNEL. This change will move
them in the driver. The intent is that if a new part comes along which
would require tweaks per IIO channel, these should be doable in the driver.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change gets rid of the AD_SD_*_CHANNEL macros in favor of defining
it's own. The ad7780 is quite simpler than it's other Sigma-Delta brothers.
It turned out that centralizing the AD_SD_*_CHANNEL macros doesn't scale
too well, especially with some more complicated drivers. Some of the
variations in the more complicated drivers require new macros, and that way
things can become harder to maintain.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* cros-usbpd-notify and cros_ec_typec
- Add a new notification driver that handles and dispatches USB PD
related events to other drivers.
- Add a Type C connector class driver for cros_ec
* CrOS EC
- Introduce a new cros_ec_cmd_xfer_status helper
* Sensors/iio:
- A series from Gwendal that adds Cros EC sensor hub FIFO support
* Wilco EC
- Fix a build warning.
- Platform data shouldn't include kernel.h
* Misc
- i2c api conversion complete, with i2c_new_client_device instead of
i2c_new_device in chromeos_laptop.
- Replace zero-length array with flexible-array member in cros_ec_chardev
and wilco_ec
- Update new structure for SPI transfer delays in cros_ec_spi
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCXo1lfQAKCRBzbaomhzOw
wo6TAQCKHOcrqq5Y9HYXs1QBx8e/0vVwe5Jh76Qi6hUVqXu56QEA65lBZ2ni8Udp
f6jQDFkaeYaF2tkghvuNoAkFRI6/rAk=
=j4Tt
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
cros-usbpd-notify and cros_ec_typec:
- Add a new notification driver that handles and dispatches USB PD
related events to other drivers.
- Add a Type C connector class driver for cros_ec
CrOS EC:
- Introduce a new cros_ec_cmd_xfer_status helper
Sensors/iio:
- A series from Gwendal that adds Cros EC sensor hub FIFO support
Wilco EC:
- Fix a build warning.
- Platform data shouldn't include kernel.h
Misc:
- i2c api conversion complete, with i2c_new_client_device instead of
i2c_new_device in chromeos_laptop.
- Replace zero-length array with flexible-array member in
cros_ec_chardev and wilco_ec
- Update new structure for SPI transfer delays in cros_ec_spi
* tag 'tag-chrome-platform-for-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux: (34 commits)
platform/chrome: cros_ec_spi: Wait for USECS, not NSECS
iio: cros_ec: Use Hertz as unit for sampling frequency
iio: cros_ec: Report hwfifo_watermark_max
iio: cros_ec: Expose hwfifo_timeout
iio: cros_ec: Remove pm function
iio: cros_ec: Register to cros_ec_sensorhub when EC supports FIFO
iio: expose iio_device_set_clock
iio: cros_ec: Move function description to .c file
platform/chrome: cros_ec_sensorhub: Add median filter
platform/chrome: cros_ec_sensorhub: Add code to spread timestmap
platform/chrome: cros_ec_sensorhub: Add FIFO support
platform/chrome: cros_ec_sensorhub: Add the number of sensors in sensorhub
platform/chrome: chromeos_laptop: make I2C API conversion complete
platform/chrome: wilco_ec: event: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_chardev: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_typec: Update port info from EC
platform/chrome: Add Type C connector class driver
platform/chrome: cros_usbpd_notify: Pull PD_HOST_EVENT status
platform/chrome: cros_usbpd_notify: Amend ACPI driver to plat
platform/chrome: cros_usbpd_notify: Add driver data struct
...
- Add support for IQS620A/621/622/624/625 Azoteq IQS62X Sensors
- New Device Support
- Add support for ADC, IRQ, Regulator, RTC and WDT to Ricoh RN5T618 PMIC
- Add support for Comet Lake to Intel LPSS
- New Functionality
- Add support for Charger Detection to Spreadtrum SC27xx PMICs
- Add support for Interrupt Polarity to Dialog Semi DA9062/61 PMIC
- Add ACPI enumeration support to Diolan DLN2 USB Adaptor
- Fix-ups
- Device Tree; iqs62x, rn5t618, cros_ec_dev, stm32-lptimer, rohm,bd71837, rohm,bd71847
- I2C registration; rn5t618
- Kconfig; MFD_CPCAP, AB8500_CORE, MFD_WM8994, MFD_WM97xx, MFD_STPMIC1
- Use flexible-array members; omap-usb-tll, qcom-pm8xxx
- Remove unnecessary casts; omap-usb-host, omap-usb-tll
- Power (suspend/resume/poweroff) enhancements; rk808
- Improve error/sanity checking; dln2
- Use snprintf(); aat2870-core
- Bug Fixes
- Fix PCI IDs; intel-lpss-pci
-----BEGIN PGP SIGNATURE-----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=hJ2o
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull mfd updates from Lee Jones:
"New Drivers:
- Add support for IQS620A/621/622/624/625 Azoteq IQS62X Sensors
New Device Support:
- Add support for ADC, IRQ, Regulator, RTC and WDT to Ricoh RN5T618 PMIC
- Add support for Comet Lake to Intel LPSS
New Functionality:
- Add support for Charger Detection to Spreadtrum SC27xx PMICs
- Add support for Interrupt Polarity to Dialog Semi DA9062/61 PMIC
- Add ACPI enumeration support to Diolan DLN2 USB Adaptor
Fix-ups:
- Device Tree; iqs62x, rn5t618, cros_ec_dev, stm32-lptimer, rohm,bd71837, rohm,bd71847
- I2C registration; rn5t618
- Kconfig; MFD_CPCAP, AB8500_CORE, MFD_WM8994, MFD_WM97xx, MFD_STPMIC1
- Use flexible-array members; omap-usb-tll, qcom-pm8xxx
- Remove unnecessary casts; omap-usb-host, omap-usb-tll
- Power (suspend/resume/poweroff) enhancements; rk808
- Improve error/sanity checking; dln2
- Use snprintf(); aat2870-core
Bug Fixes:
- Fix PCI IDs in intel-lpss-pci"
* tag 'mfd-next-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (33 commits)
mfd: intel-lpss: Fix Intel Elkhart Lake LPSS I2C input clock
mfd: aat2870: Use scnprintf() for avoiding potential buffer overflow
mfd: dln2: Allow to be enumerated via ACPI
mfd: da9062: Add support for interrupt polarity defined in device tree
dt-bindings: bd718x7: Yamlify and add BD71850
mfd: dln2: Fix sanity checking for endpoints
mfd: intel-lpss: Add Intel Comet Lake PCH-V PCI IDs
mfd: sc27xx: Add USB charger type detection support
dt-bindings: mfd: Document STM32 low power timer bindings
mfd: rk808: Convert RK805 to shutdown/suspend hooks
mfd: rk808: Reduce shutdown duplication
mfd: rk808: Stop using syscore ops
mfd: rk808: Ensure suspend/resume hooks always work
mfd: rk808: Always use poweroff when requested
mfd: omap: Remove useless cast for driver.name
mfd: Kconfig: Fix some misspelling of the word functionality
mfd: pm8xxx: Replace zero-length array with flexible-array member
mfd: omap-usb-tll: Replace zero-length array with flexible-array member
mfd: cpcap: Fix compile if MFD_CORE is not selected
mfd: cros_ec: Check DT node for usbpd-notify add
...
To be compliant with other sensors, set and get sensor sampling
frequency in Hz, not mHz.
Fixes: ae7b02ad2f ("iio: common: cros_ec_sensors: Expose cros_ec_sensors frequency range via iio sysfs")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Report the maximum amount of sample the EC can hold.
This is not tunable, but can be useful for application to find out the
maximum amount of time it can sleep when hwfifo_timeout is set to a
large number.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Expose EC minimal interrupt period through buffer/hwfifo_timeout:
- Maximal timeout is limited to 65s.
- When timeout for all sensors is set to 0, EC will not send events,
even if the sensor sampling rate is greater than 0.
Rename frequency to sampling_frequency to match IIO ABI.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Since cros_ec_sensorhub is shutting down the FIFO when the device
suspends, no need to slow down the EC sampling period rate.
It was necesseary to do that before command CMD_FIFO_INT_ENABLE was
introduced, but now all supported chromebooks have it.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
When EC supports FIFO, each IIO device registers a callback, to put
samples in the buffer when they arrives from the FIFO.
When no FIFO, the user space app needs to call trigger_new, or better
register a high precision timer.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Some IIO devices may want to override the default (realtime) to another
clock source by default.
It can beneficial when timestamps coming from the hardware or underlying
drivers are already in that format.
It can always be overridden by attribute current_timestamp_clock.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
To prevent comment rot, move function description to
cros_ec_sensors_core.c.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Introduce slv_odr in ext_info data structure in order to distinguish
between sensor hub trigger (accel sensor) odr and i2c slave odr and
properly compute samples in FIFO pattern
Fixes: e485e2a2cf ("iio: imu: st_lsm6dsx: enable sensor-hub support for lsm6dsm")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
st_lsm6dsx suffers of a read misalignment on untagged FIFO when
all 3 supported sensors (accel, gyro and ext device) are running
at different ODRs (the use-case is reported in the LSM6DSM Application
Note at pag 100).
Fix the issue taking into account decimation factor reading the FIFO
pattern.
Fixes: e485e2a2cf ("iio: imu: st_lsm6dsx: enable sensor-hub support for lsm6dsm")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This commit fixes the following error:
"BUG: sleeping function called from invalid context at kernel/irq/chip.c"
In DMA mode suppress the trigger irq handler, and make the buffer
transfers directly in DMA callback, instead.
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It should use ad7797_attribute_group in ad7797_info,
according to commit ("iio:ad7793: Add support for the ad7796 and ad7797").
Scale is fixed for the ad7796 and not programmable, hence
should not have the scale_available attribute.
Fixes: fd1a8b9128 ("iio:ad7793: Add support for the ad7796 and ad7797")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Both chips have an A/D converter capable of measuring
things like VBAT, VUSB and analog inputs.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds support for the Azoteq IQS624 and IQS625 angular position
sensors, capable of reporting the angle of a rotating shaft down to 1 and
10 degrees of accuracy, respectively.
This patch also introduces a home for linear and angular position sensors.
Unlike resolvers, they are typically contactless and use the Hall effect.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds support for the Azoteq IQS621 and IQS622 ambient light
sensors, both of which can report a four-bit representation of ambient
light intensity.
The IQS621 can additionally report illuminace directly in units of lux,
while the IQS622 can report a four-bit representation of infrared light
intensity. Furthermore, the IQS622 can report a unitless measurement of
a target's proximity to the device.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds support for the Azoteq IQS620AT temperature sensor,
capable of reporting its absolute die temperature.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch renames macro to fix the following warning generated by
checkpatch.pl:
WARNING: 'DISBLED' may be misspelled - perhaps 'DISABLED'?
Signed-off-by: Nishant Malpani <nish.malpani25@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SEMTECH SX9310/9311 driver.
The device has the following entry points:
Usual frequency:
- sampling_frequency
- sampling_frequency_available
Instant reading of current values for different sensors:
- in_proximity0_raw
- in_proximity1_raw
- in_proximity2_raw
- in_proximity3_comb_raw
and associated events in events/
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enrico Granata <egranata@chromium.org>
Signed-off-by: Daniel Campello <campello@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use devm_add_action_or_reset to automatically disable the device
when it is removed or an error occurs during probe routine.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
AD7091R is already supported by this driver. While AD7091R allows the
choice of an internal or an external voltage reference, for AD7091 the
reference is only provided by VDD. Since this information is anyway
obtained through the "vcc" regulator, no other driver changes are
required for adding AD7091 support as well.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When CONVST signal is generated internally, IIO_CHAN_INFO_RAW can be
made available for AD7091R for single reads. This patch enables it and
makes supporting more devices by this driver easier.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Compared to the other supported parts, AD7091R are dependent of
a CONVST signal that initiates the conversion. At this moment, only
sampling in buffered mode is supported for AD7091R and the only
option until now was to generate this signal externally using an
IIO trigger. This patch adds the option of generating it internally,
more compatible triggers being available in this case.
Also, it is an intermediate step of adding support more devices.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no need to call unaligned helpers on stack placed variables
because compiler will align them correctly, accordingly to architectural
ABI. Moreover, using bitwise type makes it explicit to see what we are
reading in bulk transfer. On top of that, use sizeof() instead of
magic value.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Explicit casting in printf() usually shows that something is not okay.
Here, we really don't need it by providing correct specifier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Device property API allows to gather device resources from different sources,
such as ACPI. Convert the drivers to unleash the power of device property API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use dev_get_platdata() to get the platform_data instead of
referencing it directly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
For easy grepping on debug purposes join string literals back in
the messages.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Explicit casting in printf() usually shows that something is not okay.
Here, we really don't need it by providing correct specifier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In few places the unnecessary explicit castings are being used.
Drop them for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use dev_get_platdata() to get the platform_data instead of
referencing it directly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Explicit casting in printf() usually shows that something is not okay.
Here, we really don't need it by providing correct specifier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It appears the author of the xilinx-xadc driver can't even spell his own
name correctly. Fix that.
Reported-by: Lars Möllendorf <lars.moellendorf@plating.de>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* adxl372
- Fix marking of buffered values as big endian.
* ak8974
- Fix wrong handling of negative values when read from sysfs.
* at91-sama5d2
- Fix differential mode by ensuring configuration set correctly.
* ping
- Use the write sensor type for of_ping_match table.
* sps30
- Kconfig build dependency fix.
* st-sensors
- Fix a wrong identification of which part the SMO8840 ACPI ID indicates.
* stm32-dsfdm
- Fix a sleep in atomic issue by not using a trigger when it makes no sense.
* stm32-timer
- Make sure master mode is disabled when stopping.
* vcnl400
- Update some sampling periods based on new docs.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAl5lHRwRHGppYzIzQGtl
cm5lbC5vcmcACgkQVIU0mcT0FohvfBAAnKMExW+zKhI1lyTnJQNQhed+0VfNMW7t
23VsgNQ0jLpS9eX7+1ztHhO34wP92EcvUq5p4URwEFqtQC4Ofbrm/wcYunLkmkSJ
+q1KG62jTUpQjj56iHb6OPfULEL5rdkbU+csDlrxPMk22PlWNwfCZ5mJmBJZnjDL
Jlf1ihh/3HcxCE8TavihBiryrPlNE+0C1SHWhVz0M/rOaNxOBPCKU0Oi5jf+RvZT
lpc9qhUmuM559yV4PzZQrUoJvz2OQirdzHvCtdvTM1/nbRtqoymqqQ7+6Jvhs/Wk
tUea6E5PbVV/RWC80Ezid9Z+ejOdPfBjJbEzqBCdtS2rXAhNBDyXgYjuC5h6IvRR
sdl15w6bi52uVcPWpYi016KuX7e8dPexNOS7AmxXB4V+VCORrHHlErTSJK+2O6BU
7Eeb89Jq8Azp+/Ecv9WB606/gSkfHlv94t6a+eujhb0WRqvAR0RlsTMXQnVv4tEN
T0R/Nv/kS7xgMCsRMKCeX5ZIMEsIrk0b48yk2iGWWvWzOLFiSjSmW82dcGQRW0kM
qCIf9FmAIPD0+gCZxxTMrQd+nQ9X98ZbvLPBhLLjjBim/zksxQgknkvg73jGHdZY
1McwlHrx/x1/5VUeScURA2vsTaU0yZSaSNATN3WBZqLGf8aP2GUe9cXJYb5EWoRC
eZr607TuOp0=
=uJ0W
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes in the 5.6 cycle.
* adxl372
- Fix marking of buffered values as big endian.
* ak8974
- Fix wrong handling of negative values when read from sysfs.
* at91-sama5d2
- Fix differential mode by ensuring configuration set correctly.
* ping
- Use the write sensor type for of_ping_match table.
* sps30
- Kconfig build dependency fix.
* st-sensors
- Fix a wrong identification of which part the SMO8840 ACPI ID indicates.
* stm32-dsfdm
- Fix a sleep in atomic issue by not using a trigger when it makes no sense.
* stm32-timer
- Make sure master mode is disabled when stopping.
* vcnl400
- Update some sampling periods based on new docs.
* tag 'iio-fixes-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: ping: set pa_laser_ping_cfg in of_ping_match
iio: chemical: sps30: fix missing triggered buffer dependency
iio: st_sensors: remap SMO8840 to LIS2DH12
iio: light: vcnl4000: update sampling periods for vcnl4040
iio: light: vcnl4000: update sampling periods for vcnl4200
iio: accel: adxl372: Set iio_chan BE
iio: magnetometer: ak8974: Fix negative raw values in sysfs
iio: trigger: stm32-timer: disable master mode when stopping
iio: adc: stm32-dfsdm: fix sleep in atomic context
iio: adc: at91-sama5d2_adc: fix differential channels in triggered mode
While adding a new device, I noticed these aren't sorted alphabetically [as
in the Makefile], which messed my head-up.
This change sorts the devices alphabetically in the drivers/iio/dac/Kconfig
file as well.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_{predisable,postenable} functions attach/detach
the poll functions.
For the predisable hook, the disable code should occur before detaching
the poll func, and for the postenable hook, the poll func should be
attached before the enable code.
This change moves the postenable/predisable hooks into the correct
positions.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_{predisable,postenable} functions attach/detach
the poll functions.
For the predisable hook, the disable code should occur before detaching
the poll func, and for the postenable hook, the poll func should be
attached before the enable code.
The lmp9100 was attaching a poll function but never detaching it via any
IIO disable hook.
This change adds the detaching of the poll function, and moves/renames
lmp91000_buffer_preenable() function to lmp91000_buffer_postenable().
The idea is to make it more symmetrical, so that when the
iio_triggered_buffer_{predisable,postenable} functions get removed, it's
easier to see.
Fixes: 67e17300dc ("iio: potentiostat: add LMP91000 support")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add suspend/resume PM sleep ops to stm32-timer-trigger driver.
Register contents may be lost depending on low power modes.
When going to low power, enforce the timer isn't active. Gracefully
restore its state upon resume in case it's been left enabled prior to
suspend.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
"clk_enabled" flag reflects enabled state of the timer, for master mode,
slave mode or trigger (with sampling_frequency). So rename it to "enabled".
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds a TODO file with some work items added with reference to
the conversation in [1].
A TODO file is immensely useful while onboarding new contributors who
are looking for some low hanging fruit to get their foot into the door.
Since these items affect all drivers the file has been placed in the
root iio directory instead of augmenting the staging TODO.
Thanks,
Rohit
[1]: https://marc.info/?l=linux-iio&m=158256721009892&w=2
Signed-off-by: Rohit Sarkar <rohitsarkar5398@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ACCES 104-QUAD-8 series does active filtering on the quadrature
input signals via the PC/104 bus clock (OSC 14.318 MHz). This patch
exposes the filter clock prescaler available on each channel.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
InvenSense ICP-101xx sensors are a family of barometric pressure
and temperature sensor.
These devices are I2C only and use a specific protocol of
commands/responses. Data transfer is secured by using crc8.
Driver provides processed pressure and raw temperature data.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently iio_debugfs_read_reg calls debugfs_reg_access
every time it is ran. Reading the same hardware register
multiple times during the same reading of a debugfs file
can cause unintended effects.
For example for each: cat iio:device0/direct_reg_access
the file_operations.read function will be called at least
twice. First will return the full length of the string in
bytes and the second will return 0.
This patch makes iio_debugfs_read_reg to call debugfs_reg_access
only when the user's buffer position (*ppos) is 0. (meaning
it is the beginning of a new reading of the debugfs file).
Fixes: e553f182d5 ("staging: iio: core: Introduce debugfs support, add support for direct register access")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Don't confuse user with meaningless warning about the failure in getting
regulators in case of deferred probe.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change adds support for the HMC1119 Silicon Digial Attenuator. The
HMC1119 is a broadband, highly accurate, 7-bit digital attenuator,
operating from 0.1 GHz to 6.0 GHz with 31.5 dB attenuation control range
in 0.25 dB steps.
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/hmc1119.pdf
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The chip is configured in 24 bit mode. The values read from
it must always be treated as is. This fixes the issue by
replacing the previous 16 bits value by a 24 bits buffer.
This changes affects the value output by previous version of
the driver, since the least significant byte was missing.
The upper half of 16 bit values previously output are now
the upper half of a 24 bit value.
Fixes: e01e7eaf37 ("iio: light: introduce si1133")
Reported-by: Simon Goyette <simon.goyette@gmail.com>
Co-authored-by: Guillaume Champagne <champagne.guillaume.c@gmail.com>
Signed-off-by: Maxime Roussin-Bélanger <maxime.roussinbelanger@gmail.com>
Signed-off-by: Guillaume Champagne <champagne.guillaume.c@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD5770R is a 6-channel, 14-bit resolution, low noise, programmable
current output digital-to-analog converter (DAC) for photonics control
applications.
It contains five 14-bit resolution current sourcing DAC channels and one
14-bit resolution current sourcing/sinking DAC channel.
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
