Tag was not freed in NVMD get/set data request failure scenario. This
caused a tag leak each time a request failed.
Link: https://lore.kernel.org/r/20210109123849.17098-5-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: akshatzen <akshatzen@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver initializes main configuration, general status, inbound queue
and outbound queue table addresses based on a value read from
MSGU_SCRATCH_PAD_0 register.
We should validate these addresses before dereferencing them.
Adds two validations:
1. Check if main configuration table offset lies within the pcibar
mapped
2. Check if first dword of main configuration table reads "PMCS"
There are two calls to init_pci_device_addresses() done during
pm8001_pci_probe() in this sequence:
1. First inside chip_soft_rst, where if init_pci_device_addresses fails we
will go ahead assuming MPI state is not ready and reset the device as
long as bootloader is okay. This gives chance to second call of
init_pci_device_addresses to set up the addresses after reset.
2. The second call is via pm80xx_chip_init, after soft reset is done and
firmware is checked to be ready. Once that is done we are safe to go
ahead and initialize default table values and use them.
Tests:
1. Enabled debugging logs and observed no issues during initialization,
with a controller with no issues:
pm80xx0:: pm8001_setup_msix 1034: pci_alloc_irq_vectors request ret:64 no of intr 64
pm80xx0:: init_pci_device_addresses 917: Scratchpad 0 Offset: 0x2000 value 0x40002000
pm80xx0:: init_pci_device_addresses 925: Scratchpad 0 PCI BAR: 0
pm80xx0:: init_pci_device_addresses 952: VALID main config signature 0x53434d50
pm80xx0:: init_pci_device_addresses 975: GST OFFSET 0xc4
pm80xx0:: init_pci_device_addresses 978: INBND OFFSET 0x20000128
pm80xx0:: init_pci_device_addresses 981: OBND OFFSET 0x24000928
pm80xx0:: init_pci_device_addresses 984: IVT OFFSET 0x8001408
pm80xx0:: init_pci_device_addresses 987: PSPA OFFSET 0x8001608
pm80xx0:: init_pci_device_addresses 991: addr - main cfg (ptrval) general status (ptrval)
pm80xx0:: init_pci_device_addresses 995: addr - inbnd (ptrval) obnd (ptrval)
pm80xx0:: init_pci_device_addresses 999: addr - pspa (ptrval) ivt (ptrval)
pm80xx0:: pm80xx_chip_soft_rst 1446: reset register before write : 0x0
pm80xx0:: pm80xx_chip_soft_rst 1478: reset register after write 0x40
pm80xx0:: pm80xx_chip_soft_rst 1544: SPCv soft reset Complete
pm80xx0:: init_pci_device_addresses 917: Scratchpad 0 Offset: 0x2000 value 0x40002000
pm80xx0:: init_pci_device_addresses 925: Scratchpad 0 PCI BAR: 0
pm80xx0:: init_pci_device_addresses 952: VALID main config signature 0x53434d50
pm80xx0:: init_pci_device_addresses 975: GST OFFSET 0xc4
pm80xx0:: init_pci_device_addresses 978: INBND OFFSET 0x20000128
pm80xx0:: init_pci_device_addresses 981: OBND OFFSET 0x24000928
pm80xx0:: init_pci_device_addresses 984: IVT OFFSET 0x8001408
pm80xx0:: init_pci_device_addresses 987: PSPA OFFSET 0x8001608
pm80xx0:: init_pci_device_addresses 991: addr - main cfg (ptrval) general status (ptrval)
pm80xx0:: init_pci_device_addresses 995: addr - inbnd (ptrval) obnd (ptrval)
pm80xx0:: init_pci_device_addresses 999: addr - pspa (ptrval) ivt (ptrval)
pm80xx0:: pm80xx_chip_init 1329: MPI initialize successful!
2. Tested controller with firmware known to have initialization issue and
observed no crashes with this fix:
pm80xx 0000:01:00.0: pm80xx: driver version 0.1.38
pm80xx 0000:01:00.0: Removing from 1:1 domain
pm80xx 0000:01:00.0: Requesting non-1:1 mappings
pm80xx0:: init_pci_device_addresses 948: BAD main config signature 0x0
pm80xx0:: mpi_uninit_check 1365: Failed to init pci addresses
pm80xx0:: pm80xx_chip_soft_rst 1435: MPI state is not ready scratch:0:8:62a01000:0
pm80xx0:: pm80xx_chip_soft_rst 1518: Firmware is not ready!
pm80xx0:: pm80xx_chip_soft_rst 1532: iButton Feature is not Available!!!
pm80xx0:: pm80xx_chip_init 1301: Firmware is not ready!
pm80xx0:: pm8001_pci_probe 1215: chip_init failed [ret: -16]
pm80xx: probe of 0000:01:00.0 failed with error -16
pm80xx 0000:07:00.0: pm80xx: driver version 0.1.38
pm80xx 0000:07:00.0: Removing from 1:1 domain
pm80xx 0000:07:00.0: Requesting non-1:1 mappings
scsi host6: pm80xx
pm80xx1:: pm8001_setup_sgpio 5568: failed sgpio_req timeout
pm80xx1:: mpi_phy_start_resp 3447: phy start resp status:0x0, phyid:0x0
pm80xx 0000:08:00.0: pm80xx: driver version 0.1.38
pm80xx 0000:08:00.0: Removing from 1:1 domain
pm80xx 0000:08:00.0: Requesting non-1:1 mappings
3. Without this fix we observe crash on the same controller:
pm80xx 0000:01:00.0: pm80xx: driver version 0.1.38
pm80xx 0000:01:00.0: Removing from 1:1 domain
pm80xx 0000:01:00.0: Requesting non-1:1 mappings
[<ffffffffc0451b3b>] pm80xx_chip_soft_rst+0x6b/0x4c0 [pm80xx]
[<ffffffffc043a933>] pm8001_pci_probe+0xa43/0x1630 [pm80xx]
RIP: 0010:pm80xx_chip_soft_rst+0x71/0x4c0 [pm80xx]
[<ffffffffc0451b3b>] ? pm80xx_chip_soft_rst+0x6b/0x4c0 [pm80xx]
[<ffffffffc043a933>] pm8001_pci_probe+0xa43/0x1630 [pm80xx]
pm80xx0:: mpi_uninit_check 1339: TIMEOUT:IBDB value/=2
pm80xx0:: pm80xx_chip_soft_rst 1387: MPI state is not ready scratch:0:8:62a01000:0
pm80xx0:: pm80xx_chip_soft_rst 1470: Firmware is not ready!
pm80xx0:: pm80xx_chip_soft_rst 1484: iButton Feature is not Available!!!
pm80xx0:: pm80xx_chip_init 1266: Firmware is not ready!
pm80xx0:: pm8001_pci_probe 1207: chip_init failed [ret: -16]
pm80xx: probe of 0000:01:00.0 failed with error -16
Link: https://lore.kernel.org/r/20210109123849.17098-4-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: akshatzen <akshatzen@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the controller runs into a fatal error, commands get stuck due to no
response. If the controller is in fatal error state, abort requests issued
to the controller get stuck too.
Check the controller state for fatal error conditions.
Link: https://lore.kernel.org/r/20210109123849.17098-3-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: akshatzen <akshatzen@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We do not need to busy wait during mpi_init_check() since it is not being
invoked in atomic context. mpi_init_check() is being called from
pm8001_pci_resume(), pm8001_pci_probe(). Hence we are replacing udelay with
msleep.
Link: https://lore.kernel.org/r/20210109123849.17098-2-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: akshatzen <akshatzen@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver did not return an error in the case where
pm8001_configure_phy_settings() failed.
Use rc to store the return value of pm8001_configure_phy_settings().
Link: https://lore.kernel.org/r/20201205115551.2079471-1-zhangqilong3@huawei.com
Fixes: 279094079a ("[SCSI] pm80xx: Phy settings support for motherboard controller.")
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
hw_event_sas_phy_up() is used in hardirq/softirq context:
pm8001_interrupt_handler_msix() || pm8001_interrupt_handler_intx() || pm8001_tasklet
=> PM8001_CHIP_DISP->isr() = pm80xx_chip_isr()
=> process_oq() [spin_lock_irqsave(&pm8001_ha->lock,)]
=> process_one_iomb()
=> mpi_hw_event()
=> hw_event_sas_phy_up()
=> msleep(200)
Revert the msleep() back to an mdelay() to avoid sleeping in atomic
context.
Link: https://lore.kernel.org/r/20201126132952.2287996-2-bigeasy@linutronix.de
Fixes: 4daf1ef3c6 ("scsi: pm80xx: Convert 'long' mdelay to msleep")
Cc: Vikram Auradkar <auradkar@google.com>
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are two words that need separating with a space in a pm8001_dbg()
message. Fix it.
Link: https://lore.kernel.org/r/20201124093828.307709-1-colin.king@canonical.com
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
kernel robot reported a misindentation of a goto.
Fix it.
At the same time, use a temporary for a repeated entry in the same block to
reduce visual noise.
Link: https://lore.kernel.org/r/9542a8be9954c1dca744f93f53bb1af6dd1436e8.1606192458.git.joe@perches.com
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Drivers should do only device-specific jobs. But in general, drivers using
legacy PCI PM framework for .suspend()/.resume() have to manage many PCI
PM-related tasks themselves which can be done by PCI Core itself. This
brings extra load on the driver and it directly calls PCI helper functions
to handle them.
Switch to the new generic framework by updating function signatures and
define a "struct dev_pm_ops" variable to bind PM callbacks. Also, remove
unnecessary calls to the PCI Helper functions along with the legacy
.suspend & .resume bindings.
Link: https://lore.kernel.org/r/20201102164730.324035-20-vaibhavgupta40@gmail.com
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver calls pci_enable_wake(...., false) in pm8001_pci_resume(), and
there is no corresponding pci_enable_wake(...., true) in
pm8001_pci_suspend(). Either it should do enable-wake the device in
.suspend() or should not invoke pci_enable_wake() at all.
Concluding that this driver doesn't support enable-wake and PCI core calls
pci_enable_wake(pci_dev, PCI_D0, false) during resume, drop it from
pm8001_pci__resume().
Link: https://lore.kernel.org/r/20201102164730.324035-19-vaibhavgupta40@gmail.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make the pm8001_printk() macro take an explicit HBA instead of assuming the
existence of an unspecified pm8001_ha argument.
Miscellanea:
- Add pm8001_ha to the few uses of pm8001_printk()
- Add HBA to the pm8001_dbg macro call to pm8001_printk()
Link: https://lore.kernel.org/r/0e17a4c845f15e18f98b346ffb9b039584d21cdd.1605914030.git.joe@perches.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Every PM8001_<FOO>_DBG macro uses an internal call to pm8001_printk.
Convert all uses of:
PM8001_<FOO>_DBG(hba, pm8001_printk(fmt, ...))
to
pm8001_dbg(hba, <FOO>, fmt, ...)
so the visual complexity of each macro is reduced.
The repetitive macro definitions are converted to a single pm8001_dbg and
the level is concatenated using PM8001_##level##_LOGGING for the specific
level test.
Done with coccinelle, checkpatch and a little typing of the new macro
definition.
Miscellanea:
- Coalesce formats
- Realign arguments
- Add missing terminating newlines to formats
- Remove trailing spaces from formats
- Change defective loop with printk(KERN_INFO... to emit a 16 byte hex
block to %p16h
Link: https://lore.kernel.org/r/49f36a93af7752b613d03c89a87078243567fd9a.1605914030.git.joe@perches.com
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stop typecasting the value returned by kcalloc().
Link: https://lore.kernel.org/r/20201120083648.9319-1-vulab@iscas.ac.cn
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hasn't been used since 2009.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/pm8001/pm8001_hwi.c: In function ‘mpi_set_phys_g3_with_ssc’:
drivers/scsi/pm8001/pm8001_hwi.c:415:6: warning: variable ‘value’ set but not used [-Wunused-but-set-variable]
Link: https://lore.kernel.org/r/20201116104119.816527-1-lee.jones@linaro.org
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This string is not NUL terminated.
Fixes the following W=1 kernel build warning(s):
from drivers/scsi/pm8001/pm8001_sas.c:41:
In function ‘strncpy’,
inlined from ‘pm8001_issue_ssp_tmf’ at drivers/scsi/pm8001/pm8001_sas.c:919:2:
include/linux/string.h:297:30: warning: ‘__builtin_strncpy’ specified bound 8 equals destination size [-Wstringop-truncation]
297 | #define __underlying_strncpy __builtin_strncpy
| ^
include/linux/string.h:307:9: note: in expansion of macro ‘__underlying_strncpy’
307 | return __underlying_strncpy(p, q, size);
| ^~~~~~~~~~~~~~~~~~~~
Link: https://lore.kernel.org/r/20201102102544.1018706-2-lee.jones@linaro.org
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A use-after-free or null-pointer error occurs when the 251-byte response
data is copied from IOMB buffer to response message buffer in function
pm8001_mpi_get_nvmd_resp().
After sending the command get_nvmd_data(), the caller begins to sleep by
calling wait_for_complete() and waits for the wake-up from calling
complete() in pm8001_mpi_get_nvmd_resp(). Due to unexpected events (e.g.,
interrupt), if response buffer gets freed before memcpy(), a use-after-free
error will occur. To fix this, the complete() should be called after
memcpy().
Link: https://lore.kernel.org/r/20201102165528.26510-5-Viswas.G@microchip.com.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: yuuzheng <yuuzheng@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function check_fw_ready() we busy wait using udelay. The CPU is not
released and we see need_resched failures.
Busy waiting is not necessary since we are in process context and we can
sleep instead. Replace udelay with msleep of 20 ms intervals while waiting
for firmware to become ready.
It has been verified that check_fw_ready is not being used in interrupt
context anywhere, hence it is safe to make this change.
Link: https://lore.kernel.org/r/20201102165528.26510-4-Viswas.G@microchip.com.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: akshatzen <akshatzen@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Incorrect value of the running_req was causing the driver unload to be
stuck during the SAS lldd_dev_gone notification handling. During SATA I/O
completion, for some error status values, the driver schedules the event
handler and running_req is decremented from that. However, there are some
other error status values (like IO_DS_IN_RECOVERY,
IO_XFER_ERR_LAST_PIO_DATAIN_CRC_ERR) where the I/O has already been
completed by fw/driver so running_req is not decremented.
Also during NCQ error handling, driver itself will initiate READ_LOG_EXT
and ABORT_ALL. When libsas/libata initiate READ_LOG_EXT (0x2F), driver
increments running_req. This will be completed by the driver in
pm80xx_chip_sata_req(), but running_req was not decremented.
Link: https://lore.kernel.org/r/20201102165528.26510-3-Viswas.G@microchip.com.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver submits all internal requests (like abort_task, event acknowledgment
etc.) through inbound queue 0. While submitting those, driver does not
acquire any lock and this may lead to a race when there is an I/O request
coming in on CPU0 and submitted through inbound queue 0. To avoid this,
lock acquisition has been moved to pm8001_mpi_build_cmd(). All command
submission will go through this path.
Link: https://lore.kernel.org/r/20201102165528.26510-2-Viswas.G@microchip.com.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update driver version from "0.1.39" -> "0.1.40"
Link: https://lore.kernel.org/r/20201005145011.23674-5-Viswas.G@microchip.com.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The pm80xx driver currently sets the controller queue depth to
256. Hoewver, the controller supports outstanding I/Os up 1024.
Increase the number of outstanding I/Os from 256 to 1024. CCBs and tags
are allocated according to outstanding I/Os. Also update the can_queue
value (max_out_io - PM8001_RESERVE_SLOT) used by the SCSI midlayer.
[mkp: fixed zeroday complaint]
Link: https://lore.kernel.org/r/20201005145011.23674-4-Viswas.G@microchip.com.com
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove DMA memory allocation for Devices and CCB structure. Instead
allocate memory outside of DMA memory. DMA memory is a limited system
resource and it is better to allocate memory outside of DMA memory when
possible.
Link: https://lore.kernel.org/r/20201005145011.23674-3-Viswas.G@microchip.com.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current driver uses fixed number of Inbound and Outbound queues and all of
the I/O, TMF and internal requests are submitted through those. A global
spin lock is used to control the shared access. This can create a lock
contention and it is real bottleneck in the I/O path.
To avoid this, the number of supported Inbound and Outbound queues is
increased to 64, and the number of queues used is decided based on number
of CPU cores online and number of MSI-X vectors allocated. Also add locks
per queue instead of using the global lock.
Link: https://lore.kernel.org/r/20201005145011.23674-2-Viswas.G@microchip.com.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When pm8001_tag_alloc() fails, task should be freed just like it is done in
the subsequent error paths.
Link: https://lore.kernel.org/r/20200823091453.4782-1-dinghao.liu@zju.edu.cn
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series consists of the usual driver updates (ufs, qla2xxx, tcmu,
lpfc, hpsa, zfcp, scsi_debug) and minor bug fixes. We also have a
huge docbook fix update like most other subsystems and no major update
to the core (the few non trivial updates are either minor fixes or
removing an unused feature [scsi_sdb_cache]).
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXyxq1yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishSoAAQChZ4i8
ZqYW3pL33JO3fA8vdjvLuyC489Hj4wzIsl3/bQEAxYyM6BSLvMoLWR2Plq/JmTLm
4W/LDptarpTiDI3NuDc=
=4b0W
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This consists of the usual driver updates (ufs, qla2xxx, tcmu, lpfc,
hpsa, zfcp, scsi_debug) and minor bug fixes.
We also have a huge docbook fix update like most other subsystems and
no major update to the core (the few non trivial updates are either
minor fixes or removing an unused feature [scsi_sdb_cache])"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (307 commits)
scsi: scsi_transport_srp: Sanitize scsi_target_block/unblock sequences
scsi: ufs-mediatek: Apply DELAY_AFTER_LPM quirk to Micron devices
scsi: ufs: Introduce device quirk "DELAY_AFTER_LPM"
scsi: virtio-scsi: Correctly handle the case where all LUNs are unplugged
scsi: scsi_debug: Implement tur_ms_to_ready parameter
scsi: scsi_debug: Fix request sense
scsi: lpfc: Fix typo in comment for ULP
scsi: ufs-mediatek: Prevent LPM operation on undeclared VCC
scsi: iscsi: Do not put host in iscsi_set_flashnode_param()
scsi: hpsa: Correct ctrl queue depth
scsi: target: tcmu: Make TMR notification optional
scsi: target: tcmu: Implement tmr_notify callback
scsi: target: tcmu: Fix and simplify timeout handling
scsi: target: tcmu: Factor out new helper ring_insert_padding
scsi: target: tcmu: Do not queue aborted commands
scsi: target: tcmu: Use priv pointer in se_cmd
scsi: target: Add tmr_notify backend function
scsi: target: Modify core_tmr_abort_task()
scsi: target: iscsi: Fix inconsistent debug message
scsi: target: iscsi: Fix login error when receiving
...
These are not invoked externally.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/pm8001/pm80xx_hwi.c:69:6: warning: no previous prototype for ‘pm80xx_pci_mem_copy’ [-Wmissing-prototypes]
69 | void pm80xx_pci_mem_copy(struct pm8001_hba_info *pm8001_ha, u32 soffset,
| ^~~~~~~~~~~~~~~~~~~
drivers/scsi/pm8001/pm80xx_hwi.c:5016:6: warning: no previous prototype for ‘mpi_set_phy_profile_req’ [-Wmissing-prototypes]
5016 | void mpi_set_phy_profile_req(struct pm8001_hba_info *pm8001_ha,
| ^~~~~~~~~~~~~~~~~~~~~~~
Link: https://lore.kernel.org/r/20200721164148.2617584-26-lee.jones@linaro.org
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/qla4xxx/ql4_os.c: In function ‘qla4xxx_eh_cmd_timed_out’:
drivers/scsi/qla4xxx/ql4_os.c:1865:24: warning: variable ‘sess’ set but not used [-Wunused-but-set-variable]
1865 | struct iscsi_session *sess;
| ^~~~
drivers/scsi/qla4xxx/ql4_os.c: In function ‘qla4xxx_session_create’:
drivers/scsi/qla4xxx/ql4_os.c:3079:19: warning: variable ‘dst_addr’ set but not used [-Wunused-but-set-variable]
3079 | struct sockaddr *dst_addr;
| ^~~~~~~~
drivers/scsi/qla4xxx/ql4_os.c: In function ‘qla4_8xxx_iospace_config’:
drivers/scsi/qla4xxx/ql4_os.c:5512:44: warning: variable ‘db_len’ set but not used [-Wunused-but-set-variable]
5512 | unsigned long mem_base, mem_len, db_base, db_len;
| ^~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5512:35: warning: variable ‘db_base’ set but not used [-Wunused-but-set-variable]
5512 | unsigned long mem_base, mem_len, db_base, db_len;
| ^~~~~~~
drivers/scsi/qla4xxx/ql4_os.c: In function ‘qla4xxx_get_param_ddb’:
drivers/scsi/qla4xxx/ql4_os.c:6269:24: warning: variable ‘ha’ set but not used [-Wunused-but-set-variable]
6269 | struct scsi_qla_host *ha;
| ^~
Link: https://lore.kernel.org/r/20200721164148.2617584-19-lee.jones@linaro.org
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/pm8001/pm80xx_hwi.c:918: warning: Function parameter or member 'number' not described in 'update_inbnd_queue_table'
drivers/scsi/pm8001/pm80xx_hwi.c:954: warning: Function parameter or member 'number' not described in 'update_outbnd_queue_table'
drivers/scsi/pm8001/pm80xx_hwi.c:1717: warning: Function parameter or member 'vec' not described in 'pm80xx_chip_interrupt_enable'
drivers/scsi/pm8001/pm80xx_hwi.c:1735: warning: Function parameter or member 'vec' not described in 'pm80xx_chip_interrupt_disable'
drivers/scsi/pm8001/pm80xx_hwi.c:4830: warning: Excess function parameter 'num' description in 'pm80xx_chip_phy_start_req'
drivers/scsi/pm8001/pm80xx_hwi.c:4872: warning: Excess function parameter 'num' description in 'pm80xx_chip_phy_stop_req'
drivers/scsi/pm8001/pm80xx_hwi.c:4892: warning: Function parameter or member 'pm8001_ha' not described in 'pm80xx_chip_reg_dev_req'
drivers/scsi/pm8001/pm80xx_hwi.c:4892: warning: Function parameter or member 'pm8001_dev' not described in 'pm80xx_chip_reg_dev_req'
drivers/scsi/pm8001/pm80xx_hwi.c:4892: warning: Function parameter or member 'flag' not described in 'pm80xx_chip_reg_dev_req'
drivers/scsi/pm8001/pm80xx_hwi.c:4966: warning: Function parameter or member 'phyId' not described in 'pm80xx_chip_phy_ctl_req'
drivers/scsi/pm8001/pm80xx_hwi.c:4966: warning: Function parameter or member 'phy_op' not described in 'pm80xx_chip_phy_ctl_req'
drivers/scsi/pm8001/pm80xx_hwi.c:4966: warning: Excess function parameter 'num' description in 'pm80xx_chip_phy_ctl_req'
drivers/scsi/pm8001/pm80xx_hwi.c:4966: warning: Excess function parameter 'phy_id' description in 'pm80xx_chip_phy_ctl_req'
drivers/scsi/pm8001/pm80xx_hwi.c:5006: warning: Function parameter or member 'vec' not described in 'pm80xx_chip_isr'
drivers/scsi/pm8001/pm80xx_hwi.c:5006: warning: Excess function parameter 'irq' description in 'pm80xx_chip_isr'
drivers/scsi/pm8001/pm80xx_hwi.c:5006: warning: Excess function parameter 'stat' description in 'pm80xx_chip_isr'
Link: https://lore.kernel.org/r/20200721164148.2617584-18-lee.jones@linaro.org
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Provide lots of missing descriptions, remove some superfluous ones
(probably due to docrot) and demote one header which does not provide many
descriptions, and the ones it does provide are incorrect.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/pm8001/pm8001_hwi.c:339: warning: Function parameter or member 'number' not described in 'update_inbnd_queue_table'
drivers/scsi/pm8001/pm8001_hwi.c:360: warning: Function parameter or member 'number' not described in 'update_outbnd_queue_table'
drivers/scsi/pm8001/pm8001_hwi.c:480: warning: Function parameter or member 'interval' not described in 'mpi_set_open_retry_interval_reg'
drivers/scsi/pm8001/pm8001_hwi.c:1238: warning: Function parameter or member 'int_vec_idx' not described in 'pm8001_chip_msix_interrupt_enable'
drivers/scsi/pm8001/pm8001_hwi.c:1256: warning: Function parameter or member 'int_vec_idx' not described in 'pm8001_chip_msix_interrupt_disable'
drivers/scsi/pm8001/pm8001_hwi.c:1270: warning: Function parameter or member 'vec' not described in 'pm8001_chip_interrupt_enable'
drivers/scsi/pm8001/pm8001_hwi.c:1284: warning: Function parameter or member 'vec' not described in 'pm8001_chip_interrupt_disable'
drivers/scsi/pm8001/pm8001_hwi.c:4508: warning: Excess function parameter 'num' description in 'pm8001_chip_phy_start_req'
drivers/scsi/pm8001/pm8001_hwi.c:4544: warning: Excess function parameter 'num' description in 'pm8001_chip_phy_stop_req'
drivers/scsi/pm8001/pm8001_hwi.c:4564: warning: Function parameter or member 'pm8001_ha' not described in 'pm8001_chip_reg_dev_req'
drivers/scsi/pm8001/pm8001_hwi.c:4564: warning: Function parameter or member 'pm8001_dev' not described in 'pm8001_chip_reg_dev_req'
drivers/scsi/pm8001/pm8001_hwi.c:4564: warning: Function parameter or member 'flag' not described in 'pm8001_chip_reg_dev_req'
drivers/scsi/pm8001/pm8001_hwi.c:4624: warning: Function parameter or member 'pm8001_ha' not described in 'pm8001_chip_dereg_dev_req'
drivers/scsi/pm8001/pm8001_hwi.c:4624: warning: Function parameter or member 'device_id' not described in 'pm8001_chip_dereg_dev_req'
drivers/scsi/pm8001/pm8001_hwi.c:4650: warning: Function parameter or member 'phyId' not described in 'pm8001_chip_phy_ctl_req'
drivers/scsi/pm8001/pm8001_hwi.c:4650: warning: Function parameter or member 'phy_op' not described in 'pm8001_chip_phy_ctl_req'
drivers/scsi/pm8001/pm8001_hwi.c:4650: warning: Excess function parameter 'num' description in 'pm8001_chip_phy_ctl_req'
drivers/scsi/pm8001/pm8001_hwi.c:4650: warning: Excess function parameter 'phy_id' description in 'pm8001_chip_phy_ctl_req'
drivers/scsi/pm8001/pm8001_hwi.c:4687: warning: Function parameter or member 'vec' not described in 'pm8001_chip_isr'
drivers/scsi/pm8001/pm8001_hwi.c:4687: warning: Excess function parameter 'irq' description in 'pm8001_chip_isr'
drivers/scsi/pm8001/pm8001_hwi.c:4687: warning: Excess function parameter 'stat' description in 'pm8001_chip_isr'
drivers/scsi/pm8001/pm8001_hwi.c:4727: warning: Function parameter or member 'pm8001_ha' not described in 'pm8001_chip_abort_task'
drivers/scsi/pm8001/pm8001_hwi.c:4727: warning: Function parameter or member 'pm8001_dev' not described in 'pm8001_chip_abort_task'
drivers/scsi/pm8001/pm8001_hwi.c:4727: warning: Function parameter or member 'task_tag' not described in 'pm8001_chip_abort_task'
drivers/scsi/pm8001/pm8001_hwi.c:4727: warning: Function parameter or member 'cmd_tag' not described in 'pm8001_chip_abort_task'
drivers/scsi/pm8001/pm8001_hwi.c:4727: warning: Excess function parameter 'task' description in 'pm8001_chip_abort_task'
drivers/scsi/pm8001/pm8001_hwi.c:4966: warning: Function parameter or member 'tag' not described in 'pm8001_chip_fw_flash_update_build'
Link: https://lore.kernel.org/r/20200721164148.2617584-17-lee.jones@linaro.org
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clean-up some whitespace issues too whilst we're here.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/pm8001/pm8001_ctl.c:102: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_fw_version_show'
drivers/scsi/pm8001/pm8001_ctl.c:331: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_logging_level_show'
drivers/scsi/pm8001/pm8001_ctl.c:400: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_ib_queue_log_show'
drivers/scsi/pm8001/pm8001_ctl.c:433: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_ob_queue_log_show'
drivers/scsi/pm8001/pm8001_ctl.c:464: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_bios_version_show'
drivers/scsi/pm8001/pm8001_ctl.c:623: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_gsm_log_show'
Link: https://lore.kernel.org/r/20200721164148.2617584-12-lee.jones@linaro.org
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Functions must follow directly after the header that documents them.
Fixes the following W=1 kernel build warning(s):
from drivers/scsi/pm8001/pm8001_sas.c:41:
inlined from ‘pm8001_issue_ssp_tmf’ at drivers/scsi/pm8001/pm8001_sas.c:919:2:
drivers/scsi/pm8001/pm8001_sas.c:379: warning: Function parameter or member 'pm8001_dev' not described in 'DEV_IS_GONE'
drivers/scsi/pm8001/pm8001_sas.c:379: warning: Excess function parameter 'task' description in 'DEV_IS_GONE'
drivers/scsi/pm8001/pm8001_sas.c:379: warning: Excess function parameter 'num' description in 'DEV_IS_GONE'
drivers/scsi/pm8001/pm8001_sas.c:379: warning: Excess function parameter 'gfp_flags' description in 'DEV_IS_GONE'
drivers/scsi/pm8001/pm8001_sas.c:379: warning: Excess function parameter 'is_tmf' description in 'DEV_IS_GONE'
drivers/scsi/pm8001/pm8001_sas.c:379: warning: Excess function parameter 'tmf' description in 'DEV_IS_GONE'
drivers/scsi/pm8001/pm8001_sas.c:583: warning: Function parameter or member 'device_id' not described in 'pm8001_find_dev'
drivers/scsi/pm8001/pm8001_sas.c:1000: warning: Function parameter or member 'dev' not described in 'pm8001_I_T_nexus_reset'
Link: https://lore.kernel.org/r/20200721164148.2617584-11-lee.jones@linaro.org
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
... even if they are completely unused.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/pm8001/pm8001_ctl.c:56: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_mpi_interface_rev_show'
drivers/scsi/pm8001/pm8001_ctl.c:81: warning: Function parameter or member 'attr' not described in 'controller_fatal_error_show'
drivers/scsi/pm8001/pm8001_ctl.c💯 warning: Function parameter or member 'attr' not described in 'pm8001_ctl_fw_version_show'
drivers/scsi/pm8001/pm8001_ctl.c:130: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_ila_version_show'
drivers/scsi/pm8001/pm8001_ctl.c:155: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_inactive_fw_version_show'
drivers/scsi/pm8001/pm8001_ctl.c:181: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_max_out_io_show'
drivers/scsi/pm8001/pm8001_ctl.c:204: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_max_devices_show'
drivers/scsi/pm8001/pm8001_ctl.c:230: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_max_sg_list_show'
drivers/scsi/pm8001/pm8001_ctl.c:274: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_sas_spec_support_show'
drivers/scsi/pm8001/pm8001_ctl.c:303: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_host_sas_address_show'
drivers/scsi/pm8001/pm8001_ctl.c:322: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_logging_level_show'
drivers/scsi/pm8001/pm8001_ctl.c:355: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_aap_log_show'
drivers/scsi/pm8001/pm8001_ctl.c:390: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_ib_queue_log_show'
drivers/scsi/pm8001/pm8001_ctl.c:423: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_ob_queue_log_show'
drivers/scsi/pm8001/pm8001_ctl.c:454: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_bios_version_show'
drivers/scsi/pm8001/pm8001_ctl.c:492: warning: Function parameter or member 'attr' not described in 'event_log_size_show'
drivers/scsi/pm8001/pm8001_ctl.c:510: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_iop_log_show'
drivers/scsi/pm8001/pm8001_ctl.c:548: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_fatal_log_show'
drivers/scsi/pm8001/pm8001_ctl.c:566: warning: Function parameter or member 'attr' not described in 'non_fatal_log_show'
drivers/scsi/pm8001/pm8001_ctl.c:609: warning: Function parameter or member 'attr' not described in 'pm8001_ctl_gsm_log_show'
Link: https://lore.kernel.org/r/20200713080001.128044-11-lee.jones@linaro.org
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
More bitrot issues with function documentation not keeping up with API changes.
Fixes the following W=1 kernel build warning(s):
drivers/scsi/pm8001/pm8001_init.c:64: warning: cannot understand function prototype: 'const struct pm8001_chip_info pm8001_chips[] = '
drivers/scsi/pm8001/pm8001_init.c:86: warning: cannot understand function prototype: 'struct scsi_host_template pm8001_sht = '
drivers/scsi/pm8001/pm8001_init.c:115: warning: cannot understand function prototype: 'struct sas_domain_function_template pm8001_transport_ops = '
drivers/scsi/pm8001/pm8001_init.c:212: warning: Function parameter or member 'irq' not described in 'pm8001_interrupt_handler_msix'
drivers/scsi/pm8001/pm8001_init.c:237: warning: Function parameter or member 'irq' not described in 'pm8001_interrupt_handler_intx'
drivers/scsi/pm8001/pm8001_init.c:265: warning: Function parameter or member 'ent' not described in 'pm8001_alloc'
drivers/scsi/pm8001/pm8001_init.c:624: warning: Function parameter or member 'pm8001_ha' not described in 'pm8001_init_sas_add'
drivers/scsi/pm8001/pm8001_init.c:624: warning: Excess function parameter 'chip_info' description in 'pm8001_init_sas_add'
drivers/scsi/pm8001/pm8001_init.c:900: warning: Function parameter or member 'pm8001_ha' not described in 'pm8001_setup_msix'
drivers/scsi/pm8001/pm8001_init.c:900: warning: Excess function parameter 'chip_info' description in 'pm8001_setup_msix'
drivers/scsi/pm8001/pm8001_init.c:900: warning: Excess function parameter 'irq_handler' description in 'pm8001_setup_msix'
drivers/scsi/pm8001/pm8001_init.c:981: warning: Function parameter or member 'pm8001_ha' not described in 'pm8001_request_irq'
drivers/scsi/pm8001/pm8001_init.c:981: warning: Excess function parameter 'chip_info' description in 'pm8001_request_irq'
Link: https://lore.kernel.org/r/20200713074645.126138-27-lee.jones@linaro.org
Cc: Kumar Santhanam <AnandKumar.Santhanam@pmcs.com>
Cc: Sangeetha Gnanasekaran <Sangeetha.Gnanasekaran@pmcs.com>
Cc: Nikith Ganigarakoppal <Nikith.Ganigarakoppal@pmcs.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We need ata_scsi_dma_need_drain for all drivers wired up to drive ATAPI
devices through libata. That also includes the SAS HBA drivers in addition
to native libata HBA drivers.
Link: https://lore.kernel.org/r/20200615064624.37317-3-hch@lst.de
Fixes: cc97923a5b ("block: move dma drain handling to scsi")
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Removed the common length and introduce read and write length for IOCTL
payload structure.
[mkp: fixed SoB ordering]
Link: https://lore.kernel.org/r/20200316074906.9119-7-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Viswas G <viswas.g@microchip.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added the sysfs attribute for non fatal log so that management utility can
get the non fatal dump from driver. The non-fatal error is an error
condition or abnormal behavior detected by the host, or detected and
reported by the controller to the host.The non-fatal error does not stop
the controller firmware and enables it to still respond to host requests.
A typical example of a non-fatal error is an I/O timeout or an unusual
error notification from the controller. Since the firmware is operational,
the error dump information is pushed to host memory (by firmware) upon
request from the host.
Link: https://lore.kernel.org/r/20200316074906.9119-6-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1) Move the instance tracking down after we think the instance is good to
go. Avoids having a use-after free.
2) There are goto targets for trying to cleanup if the hw fails to
initialize, but there's some overlap depending on who thinks they own
the sub-structures.
Link: https://lore.kernel.org/r/20200316074906.9119-5-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Peter Chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In pm80xx driver, the command mpi_set_phy_profile_req is sent by host
during boot to configure the phy profile such as analog setting page, rate
control page. However, the tag is not freed when its response is
received. As a result, 16 tags are missing for each HBA after boot. When
NCQ is enabled with queue depth 16, it needs at least, 15 * 16 = 240 tags
for each HBA to achieve the best performance. In current pm80xx driver with
setting CCB_MAX = 256, the total number of tags in each HBA is 255 for data
IO. Hence, without returning those tags to the pool after boot, some device
will finally be forced to non-ncq mode by ATA layer due to excessive errors
(i.e. LLDD cannot allocate tag for queued task).
Link: https://lore.kernel.org/r/20200316074906.9119-4-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: yuuzheng <yuuzheng@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A kexec reboot causes the controller fw to assert. This assertion shows up
in two ways, the controller doesn't show up as ready and an interrupt is
waiting as soon as the handler is registered. To resolve this added below
fix:
- Split the interrupt handling setup into two parts, setup and request.
- If the controller ready register indicates not-ready, but that the not
readiness is only on the IOC units we can still try a reset to bring the
system back to the pre-reboot state.
Link: https://lore.kernel.org/r/20200316074906.9119-3-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Vikram Auradkar <auradkar@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Increasing the per-request size maximum (max_sectors_kb) runs into the
per-device DMA scatter gather list limit (max_segments) for users of the io
vector system calls (eg, readv and writev). This is because the kernel
combines io vectors into DMA segments when possible, but it doesn't work
for our user because the vectors in the buffer cache get scrambled. This
change bumps the advertised max scatter gather length to 528 to cover 2M w/
x86's 4k pages and some extra for the user checksum. It trims the size of
some of the tables we don't care about and exposes all of the command slots
upstream to the SCSI layer. Also reduced the PM8001_MAX_CCB to 256 as
pm8001 driver has memory limit depend on machine capability. If we increase
the sg length, we need to trade-off it by decreasing PM8001_MAX_CCB.
PM8001_MAX_CCB = 256 does not have any influence on normal use
Link: https://lore.kernel.org/r/20200316074906.9119-2-deepak.ukey@microchip.com
Reported-by: kbuild test robot <lkp@intel.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Peter Chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a spelling mistake in a pm8001_printk message. Fix it.
Link: https://lore.kernel.org/r/20200123005706.2834281-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The ata_sas_scsi_ioctl() function implements a number of HDIO_* commands
for SCSI devices, it is used by all libata drivers as well as a few
drivers that support SAS attached SATA drives.
The only command that is not safe for compat ioctls here is
HDIO_GET_32BIT. Change the implementation to check for in_compat_syscall()
in order to do both cases correctly, and change all callers to use it
as both native and compat callback pointers, including the indirect
callers through sas_ioctl and ata_scsi_ioctl.
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
11 patches, all in drivers (no core changes) that are either minor
cleanups or small fixes. They were late arriving, but still safe for
-rc1.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXeyDEiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbijAQDIuM45
xeEXgWXF8c/tYuvildK1WjyVzwBO2k563lUmYQEA4rxSzkmhtcaMTDuk4hI4Y4TP
p87U1bXNSJ7tCpFU15w=
=W43H
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"Eleven patches, all in drivers (no core changes) that are either minor
cleanups or small fixes.
They were late arriving, but still safe for -rc1"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: MAINTAINERS: Add the linux-scsi mailing list to the ISCSI entry
scsi: megaraid_sas: Make poll_aen_lock static
scsi: sd_zbc: Improve report zones error printout
scsi: qla2xxx: Fix qla2x00_request_irqs() for MSI
scsi: qla2xxx: unregister ports after GPN_FT failure
scsi: qla2xxx: fix rports not being mark as lost in sync fabric scan
scsi: pm80xx: Remove unused include of linux/version.h
scsi: pm80xx: fix logic to break out of loop when register value is 2 or 3
scsi: scsi_transport_sas: Fix memory leak when removing devices
scsi: lpfc: size cpu map by last cpu id set
scsi: ibmvscsi_tgt: Remove unneeded variable rc
-----BEGIN PGP SIGNATURE-----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=uUXw
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Warn if a host bridge has no NUMA info (Yunsheng Lin)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis
Efremov)
Resource management:
- Fix boot-time Embedded Controller GPE storm caused by incorrect
resource assignment after ACPI Bus Check Notification (Mika
Westerberg)
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control
the MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA
devices downstream (Subbaraya Sundeep)
- Consolidate DT "dma-ranges" parsing and convert all host drivers to
use shared parsing (Rob Herring)
Error reporting:
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC
even if platform didn't grant control over AER (Olof Johansson)
Hotplug:
- Avoid returning prematurely from sysfs requests to enable or
disable a PCIe hotplug slot (Lukas Wunner)
- Don't disable interrupts twice when suspending hotplug ports (Mika
Westerberg)
- Fix deadlocks when PCIe ports are hot-removed while suspended (Mika
Westerberg)
Power management:
- Remove unnecessary ASPM locking (Bjorn Helgaas)
- Add support for disabling L1 PM Substates (Heiner Kallweit)
- Allow re-enabling Clock PM after it has been disabled (Heiner
Kallweit)
- Add sysfs attributes for controlling ASPM link states (Heiner
Kallweit)
- Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl"
sysfs files (Heiner Kallweit)
- Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on
USB 2.0 or 1.1 connect events (Kai-Heng Feng)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk
for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we
only did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn
Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0)
instead of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
Virtualization:
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn
Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the
VFs, but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and
associated VFs can be enabled independently (Kuppuswamy
Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof
Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn
Helgaas)
- Hide PRI and PASID state restoration functions used only inside the
PCI core (Bjorn Helgaas)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George
Cherian)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Unify ACS quirk implementations (Bjorn Helgaas)
Amlogic Meson host bridge driver:
- Fix meson PERST# GPIO polarity problem (Remi Pommarel)
- Add DT bindings for Amlogic Meson G12A (Neil Armstrong)
- Fix meson clock names to match DT bindings (Neil Armstrong)
- Add meson support for Amlogic G12A SoC with separate shared PHY
(Neil Armstrong)
- Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe
combo PHY (Neil Armstrong)
- Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)
- Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT
(Neil Armstrong)
Broadcom iProc host bridge driver:
- Invalidate iProc PAXB address mapping before programming it
(Abhishek Shah)
- Fix iproc-msi and mvebu __iomem annotations (Ben Dooks)
Cadence host bridge driver:
- Refactor Cadence PCIe host controller to use as a library for both
host and endpoint (Tom Joseph)
Freescale Layerscape host bridge driver:
- Add layerscape LS1028a support (Xiaowei Bao)
Intel VMD host bridge driver:
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
Marvell ARMADA 3700 / Aardvark host bridge driver:
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted
before the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi
Pommarel)
- Don't rely on jiffies in Aardvark config access path since
interrupts may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
Marvell ARMADA 370 / XP host bridge driver:
- Make mvebu_pci_bridge_emul_ops static (Ben Dooks)
Microsoft Hyper-V host bridge driver:
- Add hibernation support for Hyper-V virtual PCI devices (Dexuan
Cui)
- Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan
Cui)
- Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui)
Mobiveil host bridge driver:
- Change mobiveil csr_read()/write() function names that conflict
with riscv arch functions (Kefeng Wang)
NVIDIA Tegra host bridge driver:
- Fix Tegra CLKREQ dependency programming (Vidya Sagar)
Renesas R-Car host bridge driver:
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro
Shimoda)
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual
(Yoshihiro Shimoda)
- Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon
Horman)
Rockchip host bridge driver:
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin
Murphy)
Socionext UniPhier host bridge driver:
- Set uniphier to host (RC) mode always (Kunihiko Hayashi)
Endpoint drivers:
- Fix endpoint driver sign extension problem when shifting page
number to phys_addr_t (Alan Mikhak)
Misc:
- Add NumaChip SPDX header (Krzysztof Wilczynski)
- Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)
- Remove unused includes (Krzysztof Wilczynski)
- Removed unused sysfs attribute groups (Ben Dooks)
- Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)
- Add PCIe Link Control 2 register field definitions to replace magic
numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)
- Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and
Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas)
- Use pcie_capability_read_word() instead of pci_read_config_word()
in AMDGPU and Radeon CIK/SI (Frederick Lawler)
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
- Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe)
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
- Fix dwc find_next_bit() usage (Niklas Cassel)
- Fix pcitest.c fd leak (Hewenliang)
- Fix typos and comments (Bjorn Helgaas)
- Fix Kconfig whitespace errors (Krzysztof Kozlowski)"
* tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits)
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer
PCI: hv: Change pci_protocol_version to per-hbus
PCI: hv: Add hibernation support
PCI: hv: Reorganize the code in preparation of hibernation
MAINTAINERS: Remove Keith from VMD maintainer
PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code
PCI/ASPM: Add sysfs attributes for controlling ASPM link states
PCI: Fix indentation
drm/radeon: Prefer pcie_capability_read_word()
drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/radeon: Correct Transmit Margin masks
drm/amdgpu: Prefer pcie_capability_read_word()
PCI: uniphier: Set mode register to host mode
drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
...
Remove #include <linux/version.h>. Don't need it.
Link: https://lore.kernel.org/r/20191122020911.33269-1-yuehaibing@huawei.com
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The condition (reg_val != 2) || (reg_val != 3) will always be true because
reg_val cannot be equal to two different values at the same time. Fix this
by replacing the || operator with && so that the loop will loop if reg_val
is not a 2 and not a 3 as was originally intended.
Fixes: 50dc2f221455 ("scsi: pm80xx: Modified the logic to collect fatal dump")
Link: https://lore.kernel.org/r/20191120135031.270708-1-colin.king@canonical.com
Addresses-Coverity: ("Constant expression result")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added the correct method to collect the fatal dump.
Link: https://lore.kernel.org/r/20191114100910.6153-14-deepak.ukey@microchip.com
Reported-by: kbuild test robot <lkp@intel.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With MSI-x enabled, the interrupt instances are <prefix><index> where the
prefix is fixed for all module instances, making it a little harder to
track down what's what.
Link: https://lore.kernel.org/r/20191114100910.6153-13-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Vikram Auradkar <auradkar@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added support to check controller fatal error through sysfs.
Link: https://lore.kernel.org/r/20191114100910.6153-12-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Occasionally, 6G capable drives fail to train at 6G on links that look good
from a signal-integrity perspective. PMC suggests configuring the port to
not even expect 12G.
Link: https://lore.kernel.org/r/20191114100910.6153-11-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added the fix so the if driver properly sent the abort it tries to remove
it from the firmware's list of outstanding commands regardless of the abort
status. This means that the task gets freed 'now' rather than possibly
getting freed later when the scsi layer thinks it's leaked but still valid.
Link: https://lore.kernel.org/r/20191114100910.6153-10-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The commands to the controller are sent in fixed sized chunks which are set
per-chip-generation and stashed in iomb_size. The driver fills in structs
matching the register layout and memcpy this to memory shared with the
controller. However, there are two problem cases:
1) Things like phy_start_req are too large because they share the
sas_identify_frame definition with libsas, and it includes the crc
word. This means that it's overwriting the start of the next
command block, that's ok except if it happens at the end of the
shared memory area.
2) Things like set_nvm_data_req which are shared between the HAL
layers. This means that it's sending 'random' data for things that
are in the reserved area. So far we haven't found a case where the
controller FW cares, but sending possible gibberish (for most of
the structures this is in the reserved area so previously zeroed)
is not recommended.
Link: https://lore.kernel.org/r/20191114100910.6153-9-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sas_task structure should not be used after task_done is called. If the
device is gone or not attached, we call task_done on t and continue to use
in the sas_task in rest of the function. task_done is pointing to
sas_ata_task_done, may free the memory associated with the task before
returning.
Link: https://lore.kernel.org/r/20191114100910.6153-8-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Vikram Auradkar <auradkar@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The function mpi_uninit_check takes longer for inbound doorbell register to
be cleared. Increased the timeout substantially so that the driver does not
fail to load.
Link: https://lore.kernel.org/r/20191114100910.6153-7-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: ianyar <ianyar@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The default logging doesn't include the device name, so it's difficult to
determine which controller is being logged about in error scenarios. The
logging level was only settable via sysfs, which made it inconvenient for
actual debugging. This changes the default to only cover error handling.
Link: https://lore.kernel.org/r/20191114100910.6153-6-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For delays longer than 20ms [um]delay isn't recommended.
pm80xx_chip_soft_rst starts off with a 500ms delay before it even gets
around to checking for the results of the reset. As long as it's at least
500ms it doesn't matter what the scheduler is doing. The delay in the
pm8001_exec_internal_task_abort does nothing, and theory is this is a delay
to avoid a double-free.
Link: https://lore.kernel.org/r/20191114100910.6153-5-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Vikram Auradkar <auradkar@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In pm8001_task_exec(), if the PHY is down, then we return the current value
of 'rc'. We need to make sure it's initialized.
Link: https://lore.kernel.org/r/20191114100910.6153-4-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After the completing the mpi_phy_start_resp, make phy enable completion as
NULL.
Link: https://lore.kernel.org/r/20191114100910.6153-3-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver was missing complete() call in mpi_sata_completion which result in
SATA abort error handling timing out. That causes the device to be left in
the in_recovery state so subsequent commands sent to the device fail and
the OS removes access to it.
Link: https://lore.kernel.org/r/20191114100910.6153-2-deepak.ukey@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: peter chang <dpf@google.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace assignment of 0 to pointer with NULL assignment.
Link: https://lore.kernel.org/r/20191025135010.GA6191@saurav
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Code that iterates over all standard PCI BARs typically uses
PCI_STD_RESOURCE_END. However, that requires the unusual test
"i <= PCI_STD_RESOURCE_END" rather than something the typical
"i < PCI_STD_NUM_BARS".
Add a definition for PCI_STD_NUM_BARS and change loops to use the more
idiomatic C style to help avoid fencepost errors.
Link: https://lore.kernel.org/r/20190927234026.23342-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190927234308.23935-1-efremov@linux.com
Link: https://lore.kernel.org/r/20190916204158.6889-3-efremov@linux.com
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sebastian Ott <sebott@linux.ibm.com> # arch/s390/
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> # video/fbdev/
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com> # pci/controller/dwc/
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com> # scsi/pm8001/
Acked-by: Martin K. Petersen <martin.petersen@oracle.com> # scsi/pm8001/
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # memstick/
There are several occasions where variable rc is being initialized with a
value that is never read and error is being re-assigned a little later on.
Clean up the code by removing rc entirely and just returning the return
value from the call to pm8001_issue_ssp_tmf
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Disabling the SATA drive interface cause kernel panic. When the drive
Interface is disabled, device should be deregistered after aborting all
pending I/Os. Also changed the port recovery timeout to 10000 ms for
PM8006 controller.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added the logic for collecting IOP log respective to event log size.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added support to read event log size from MPI configuration table and
export through sysfs.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Many times in libsas, and in LLDDs which use libsas, the check for an
expander device is re-implemented or open coded.
Use dev_is_expander() instead. We rename this from
sas_dev_type_is_expander() to not spill so many lines in referencing.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix abord to abort.
Signed-off-by: Weitao Hou <houweitaoo@gmail.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename the functions pm8001_chip_is_our_interupt,
pm80xx_chip_is_our_interupt and function pointer is_our_interrupt to fix
spelling mistakes.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When macro PM8001_USE_MSIX is defined there are redundant dead code calls
to pm8001_chip_intx_interrupt_{enable|disable} and pm8001_cr32.
Clean this up for the defined PM8001_USE_MSIX and undefined
PM8001_USE_MSIX cases.
[mkp: squashed two patches]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/pm8001/pm8001_hwi.c: In function 'mpi_smp_completion':
drivers/scsi/pm8001/pm8001_hwi.c:2901:6: warning:
variable 'param' set but not used [-Wunused-but-set-variable]
drivers/scsi/pm8001/pm8001_hwi.c: In function 'pm8001_bytes_dmaed':
drivers/scsi/pm8001/pm8001_hwi.c:3247:24: warning:
variable 'sas_ha' set but not used [-Wunused-but-set-variable]
They're never used since introduction, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are several lines of code where the indentation is at an incorrect
level; fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A set of 17 fixes. Most of these are minor or trivial. The one fix
that may be serious is the isci one: the bug can cause hba parameters
to be set from uninitialized memory. I don't think it's exploitable,
but you never know.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXEKL0SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishVZpAQCwuPTk
fqOt4v4hJ0oUHtEBsQK3VMXSdUvWdb5Lbn3WeQD/RFYTyNxcIF7ADSWw71b+IigT
ejUrMzI8ig+nZ1jbFZ4=
=BdS/
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A set of 17 fixes. Most of these are minor or trivial.
The one fix that may be serious is the isci one: the bug can cause hba
parameters to be set from uninitialized memory. I don't think it's
exploitable, but you never know"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: cxgb4i: add wait_for_completion()
scsi: qla1280: set 64bit coherent mask
scsi: ufs: Fix geometry descriptor size
scsi: megaraid_sas: Retry reads of outbound_intr_status reg
scsi: qedi: Add ep_state for login completion on un-reachable targets
scsi: ufs: Fix system suspend status
scsi: qla2xxx: Use correct number of vectors for online CPUs
scsi: hisi_sas: Set protection parameters prior to adding SCSI host
scsi: tcmu: avoid cmd/qfull timers updated whenever a new cmd comes
scsi: isci: initialize shost fully before calling scsi_add_host()
scsi: lpfc: lpfc_sli: Mark expected switch fall-throughs
scsi: smartpqi_init: fix boolean expression in pqi_device_remove_start
scsi: core: Synchronize request queue PM status only on successful resume
scsi: pm80xx: reduce indentation
scsi: qla4xxx: check return code of qla4xxx_copy_from_fwddb_param
scsi: megaraid_sas: correct an info message
scsi: target/iscsi: fix error msg typo when create lio_qr_cache failed
scsi: sd: Fix cache_type_store()
Delete tab aligning a statement with the right hand side of a preceding
assignment rather than the left hand side.
Found with the help of Coccinelle.
[mkp: added space]
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Most SCSI drivers want to enable "clustering", that is merging of
segments so that they might span more than a single page. Remove the
ENABLE_CLUSTERING define, and require drivers to explicitly set
DISABLE_CLUSTERING to disable this feature.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/pm8001/pm80xx_hwi.c: In function 'pm8001_set_phy_profile':
drivers/scsi/pm8001/pm80xx_hwi.c:4679:6: warning:
variable 'page_code' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/pm8001/pm8001_sas.c: In function 'pm8001_I_T_nexus_event_handler':
drivers/scsi/pm8001/pm8001_sas.c:1052:6: warning:
variable 'device_id' set but not used [-Wunused-but-set-variable]
drivers/scsi/pm8001/pm8001_sas.c: In function 'pm8001_abort_task':
drivers/scsi/pm8001/pm8001_sas.c:1191:6: warning:
variable 'device_id' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated the driver version from 0.1.38 to 0.1.39.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the firmware is not responding, execution of kexec boot causes a system
hang. When firmware assertion happened, driver get notified with interrupt
vector updated in MPI configuration table. Then, the driver will read
scratchpad register and set controller_fatal_error flag to true.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For the function dma_unmap_sg(), the <nents> parameter should be number of
elements in the scatter list prior to the mapping, not after the mapping.
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added proper mask for phy id in mpi_phy_stop_resp().
Signed-off-by: Deepak Ukey <deepak.ukey@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistake in pm8001_printk message text; also I
believe NOT_UNSUPPORTED should probably be NOT_SUPPORTED. Also fix the
indent of the pm8001_printk statement.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With all callbacks converted, and the timer callback prototype
switched over, the TIMER_FUNC_TYPE cast is no longer needed,
so remove it. Conversion was done with the following scripts:
perl -pi -e 's|\(TIMER_FUNC_TYPE\)||g' \
$(git grep TIMER_FUNC_TYPE | cut -d: -f1 | sort -u)
perl -pi -e 's|\(TIMER_DATA_TYPE\)||g' \
$(git grep TIMER_DATA_TYPE | cut -d: -f1 | sort -u)
The now unused macros are also dropped from include/linux/timer.h.
Signed-off-by: Kees Cook <keescook@chromium.org>
This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes).
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJaCxtCAAoJEAVr7HOZEZN4d9EQAI+OHP6ss6zjKKC21c9jNPcH
NhLrNv37gHg/LA2VXeUEL9RGUjCGLIUrI4HsrxzkFAMLKP4TkshMs8/2RvczY+Sa
VpayPqVybEKLIS6ipQyM1SLIQff2nvtDVcN/T+8z1lkk45TrbA6ZGuwUwd2aJyEA
2V2wtg51ObnL0Nr9QPPll0JrtL1AnCZyRlu9XrwTZuuSBZwk93opIuuvbZm/3dVg
Ir4GSS4Y+PuHIfu4cxqdsPMdzRdY9I2me1YiE4jeFSn1/VTAjL4HBz7fO9eITT42
VhXSpDz1XvFsa9dJ0ubkqoALpJzCfOcBw+EuGvSydLEvOBoEVwMccdfaD9lT1zc5
L9e1Z5qqJoq7hTA6xTXCYfWG73I9HYvljtmc8yudKHhADOdnSTUXhaO6uBF0RNqD
OxPSA1RZwRx3c6lDOcK6BTtvLAkTEuYKdrWSKJi0w+QXJAyQ6etqbmsKpmPdRim7
Z4ZSpJFro2gyo9gcdJO0ykTG+z3U7Z/ay1sNgnuprsv+eU/QjUdlAPl18o79EkRf
H54zZggZ4wC6q/cFVVt4Vx+V+oqIeu38s7NDXS9UltLoTZPm2EzDW6pXd/38Z4Tf
a1oBAUET8kYLC90P8sVZxUIHZjITlpgDbyE2Lq00PMYXhk8S4IxF0aMN5RvVqzUv
+7N2HrHkSSgG1nhw1t+E
=3O85
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: lpfc: Fix hard lock up NMI in els timeout handling.
scsi: mpt3sas: remove a stray KERN_INFO
scsi: mpt3sas: cleanup _scsih_pcie_enumeration_event()
scsi: aacraid: use timespec64 instead of timeval
scsi: scsi_transport_fc: add 64GBIT and 128GBIT port speed definitions
scsi: qla2xxx: Suppress a kernel complaint in qla_init_base_qpair()
scsi: mpt3sas: fix dma_addr_t casts
scsi: be2iscsi: Use kasprintf
scsi: storvsc: Avoid excessive host scan on controller change
scsi: lpfc: fix kzalloc-simple.cocci warnings
scsi: mpt3sas: Update mpt3sas driver version.
scsi: mpt3sas: Fix sparse warnings
scsi: mpt3sas: Fix nvme drives checking for tlr.
scsi: mpt3sas: NVMe drive support for BTDHMAPPING ioctl command and log info
scsi: mpt3sas: Add-Task-management-debug-info-for-NVMe-drives.
scsi: mpt3sas: scan and add nvme device after controller reset
scsi: mpt3sas: Set NVMe device queue depth as 128
scsi: mpt3sas: Handle NVMe PCIe device related events generated from firmware.
scsi: mpt3sas: API's to remove nvme drive from sml
scsi: mpt3sas: API 's to support NVMe drive addition to SML
...
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. This requires adding a pointer to
hold the timer's target task, as there isn't a link back from slow_task.
Cc: John Garry <john.garry@huawei.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Jack Wang <jinpu.wang@profitbricks.com>
Cc: lindar_liu@usish.com
Cc: Jens Axboe <axboe@fb.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Benjamin Block <bblock@linux.vnet.ibm.com>
Cc: Baoyou Xie <baoyou.xie@linaro.org>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: John Garry <john.garry@huawei.com> # for hisi_sas part
Tested-by: John Garry <john.garry@huawei.com> # basic sanity test for hisi_sas
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Corrected the value defined for LINKRATE_60 (6 Gig).
Signed-off-by: Raj Dinesh <Raj.Dinesh@microsemi.com>
Signed-off-by: Viswas G <viswas.g@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
when there's an error in 'ncq mode' the host has to read the ncq error
log (10h) to clear the error state. however, the ccb that is setup for
doing this doesn't setup the ccb so that the previous state is
cleared. if the ccb was previously used for an IO n_elems is set and
pm8001_ccb_task_free() treats this as the signal to go free a
scatter-gather list (that's already been freed).
Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modified SATA abort handling with following steps:
1) Set device state as recovery.
2) Send phy reset.
3) Wait for reset completion.
4) After successful reset, abort all IO's to the device.
5) After aborting all IO's to device, set device state as operational.
Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added port reset timer value as 2000ms for PM8006 sata controller.
Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
tag is taken from the tag pool instead of using the hardcoded tag
value(1).
Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Different SAS addresses are assigned for each set of phys.
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added support to read ILA version and inactive firmware version from MPI
configuration table and export through sysfs.
Signed-off-by: Deepak Ukey <deepak.ukey@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sas_identify structure defined by pm80xx doesn't have CRC field. So
added a new sas_identify structure without CRC.
Signed-off-by: Raj Dinesh <Raj.Dinesh@microsemi.com>
Signed-off-by: Viswas G <Viswas.G@microsemi.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
