[ Upstream commit ac67b07e26 ]
Currently, the aspeed-sgpio driver exposes up to 80 GPIO lines,
corresponding to the 80 status bits available in hardware. Each of these
lines can be configured as either an input or an output.
However, each of these GPIOs is actually an input *and* an output; we
actually have 80 inputs plus 80 outputs.
This change expands the maximum number of GPIOs to 160; the lower half
of this range are the input-only GPIOs, the upper half are the outputs.
We fix the GPIO directions to correspond to this mapping.
This also fixes a bug when setting GPIOs - we were reading from the
input register, making it impossible to set more than one output GPIO.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae7 ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c149b7d75 ]
The required supplies in bindings were actually not matching
implementation making the bindings incorrect and misleading. The Linux
kernel driver requires all supplies to be present. Also for wlf,wm8994
uses just DBVDD-supply instead of DBVDDn-supply (n: <1,3>).
Reported-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200501133534.6706-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d157c28d2 ]
This patch updates the documentation with the information related
to the quirks that needs to be added for disabling all SuperSpeed XHCI
instances in park mode.
Cc: Dongjin Kim <tobetter@gmail.com>
Cc: Jianxin Pan <jianxin.pan@amlogic.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Jun Li <lijun.kernel@gmail.com>
Reported-by: Tim <elatllat@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35b9c0fdb9 ]
Fix unit address to match the first address specified in the reg
property of the node in example.
Signed-off-by: Kangmin Park <l4stpr0gr4m@gmail.com>
Link: https://lore.kernel.org/r/20200625135158.5861-1-l4stpr0gr4m@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0ff9b5907 ]
Add property "pinctrl-names" to swap pin mode between gpio and dpi mode.
Set the dpi pins to gpio mode and output-low to avoid leakage current
when dpi disabled.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9f711efd4 ]
If the kernel configuration option CONFIG_PCIE_DW_PLAT_HOST is enabled
then this can cause the kernel to incorrectly probe the generic
designware PCIe platform driver instead of the Tegra194 designware PCIe
driver. This causes a boot failure on Tegra194 because the necessary
configuration to access the hardware is not performed.
The order in which the compatible strings are populated in Device-Tree
is not relevant in this case, because the kernel will attempt to probe
the device as soon as a driver is loaded and if the generic designware
PCIe driver is loaded first, then this driver will be probed first.
Therefore, to fix this problem, remove the "snps,dw-pcie" string from
the compatible string as we never want this driver to be probe on
Tegra194.
Fixes: 2602c32f15 ("arm64: tegra: Add P2U and PCIe controller nodes to Tegra194 DT")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26d5bb9e4c ]
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak; thus stopping further packet processing.
The FMAN internal queue can overflow when FMAN splits single
read or write transactions into multiple smaller transactions
such that more than 17 AXI transactions are in flight from FMAN
to interconnect. When the FMAN internal queue overflows, it can
stall further packet processing. The issue can occur with any one
of the following three conditions:
1. FMAN AXI transaction crosses 4K address boundary (Errata
A010022)
2. FMAN DMA address for an AXI transaction is not 16 byte
aligned, i.e. the last 4 bits of an address are non-zero
3. Scatter Gather (SG) frames have more than one SG buffer in
the SG list and any one of the buffers, except the last
buffer in the SG list has data size that is not a multiple
of 16 bytes, i.e., other than 16, 32, 48, 64, etc.
With any one of the above three conditions present, there is
likelihood of stalled FMAN packet processing, especially under
stress with multiple ports injecting line-rate traffic.
To avoid situations that stall FMAN packet processing, all of the
above three conditions must be avoided; therefore, configure the
system with the following rules:
1. Frame buffers must not span a 4KB address boundary, unless
the frame start address is 256 byte aligned
2. All FMAN DMA start addresses (for example, BMAN buffer
address, FD[address] + FD[offset]) are 16B aligned
3. SG table and buffer addresses are 16B aligned and the size
of SG buffers are multiple of 16 bytes, except for the last
SG buffer that can be of any size.
Additional workaround notes:
- Address alignment of 64 bytes is recommended for maximally
efficient system bus transactions (although 16 byte alignment is
sufficient to avoid the stall condition)
- To support frame sizes that are larger than 4K bytes, there are
two options:
1. Large single buffer frames that span a 4KB page boundary can
be converted into SG frames to avoid transaction splits at
the 4KB boundary,
2. Align the large single buffer to 256B address boundaries,
ensure that the frame address plus offset is 256B aligned.
- If software generated SG frames have buffers that are unaligned
and with random non-multiple of 16 byte lengths, before
transmitting such frames via FMAN, frames will need to be copied
into a new single buffer or multiple buffer SG frame that is
compliant with the three rules listed above.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a6c4f77cb3 upstream.
This patch set the correct value for oversampling maxItems. In the
original example, appears 3 items for oversampling while the maxItems
is set to 1, this patch fixes those issues.
Fixes: 416f882c3b ("dt-bindings: iio: adc: Migrate AD7606 documentation to yaml")
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0c0ef9ea6f ]
Commit 0ed266d7ae ("clk: ti: omap3: cleanup unnecessary clock aliases")
removed old omap3 clock framework aliases but caused omap3-rom-rng to
stop working with clock not found error.
Based on discussions on the mailing list it was requested by Tero Kristo
that it would be best to fix this issue by probing omap3-rom-rng using
device tree to provide a proper clk property. The other option would be
to add back the missing clock alias, but that does not help moving things
forward with removing old legacy platform_data.
Let's also add a proper device tree binding and keep it together with
the fix.
Cc: devicetree@vger.kernel.org
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Fixes: 0ed266d7ae ("clk: ti: omap3: cleanup unnecessary clock aliases")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit dbce0b6504 upstream.
DT property definitions must be under a 'properties' keyword. This was
missing for 'snps,tso' in an if/then clause. A meta-schema fix will
catch future errors like this.
Fixes: 7db3545aef ("dt-bindings: net: stmmac: Convert the binding to a schemas")
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 392a9f6305 upstream.
The reset controller has a #reset-cells value of 1, so we should see a
phandle plus a register identifier, fix the example.
Fixes: 0807caf647 ("dt-bindings: reset: Add document for Broadcom STB reset controller")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 93512dad33 ]
Schema errors can cause make to exit before useful information is
printed. This leaves developers wondering what's wrong. It can be
overcome passing '-k' to make, but that's not an obvious solution.
There's 2 scenarios where this happens.
When using DT_SCHEMA_FILES to validate with a single schema, any error
in the schema results in processed-schema.yaml being empty causing a
make error. The result is the specific errors in the schema are never
shown because processed-schema.yaml is the first target built. Simply
making processed-schema.yaml last in extra-y ensures the full schema
validation with detailed error messages happen first.
The 2nd problem is while schema errors are ignored for
processed-schema.yaml, full validation of the schema still runs in
parallel and any schema validation errors will still stop the build when
running validation of dts files. The fix is to not add the schema
examples to extra-y in this case. This means 'dtbs_check' is no longer a
superset of 'dt_binding_check'. Update the documentation to make this
clear.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7165ef890a upstream.
The introduction of 768ec4c012 ("ath10k: update HOST capability QMI
message") served the purpose of supporting the new and extended HOST
capability QMI message.
But while the new message adds a slew of optional members it changes the
data type of the "daemon_support" member, which means that older
versions of the firmware will fail to decode the incoming request
message.
There is no way to detect this breakage from Linux and there's no way to
recover from sending the wrong message (i.e. we can't just try one
format and then fallback to the other), so a quirk is introduced in
DeviceTree to indicate to the driver that the firmware requires the 8bit
version of this message.
Cc: stable@vger.kernel.org
Fixes: 768ec4c012 ("ath10k: update HOST capability qmi message")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A slightly larger set of fixes have accrued in the last two weeks.
Mostly a collection of the usual smaller fixes:
- Marvell Armada: USB phy setup issues on Turris Mox
- Broadcom: GPIO/pinmux DT mapping corrections for Stingray, MMC bus
width fix for RPi Zero W, GPIO LED removal for RPI CM3. Also some
maintainer updates.
- OMAP: Fixlets for display config, interrupt settings for wifi, some
clock/PM pieces. Also IOMMU regression fix and a ti-sysc no-watchdog
regression fix.
- i.MX: A few fixes around PM/settings, some devicetree fixlets and
catching up with config option changes in DRM
- Rockchip: RockRro64 misc DT fixups, Hugsun X99 USB-C, Kevin display
panel settings
... and some smaller fixes for Davinci (backlight, McBSP DMA), Allwinner
(phy regulators, PMU removal on A64, etc).
-----BEGIN PGP SIGNATURE-----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=Jy/6
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A slightly larger set of fixes have accrued in the last two weeks.
Mostly a collection of the usual smaller fixes:
- Marvell Armada: USB phy setup issues on Turris Mox
- Broadcom: GPIO/pinmux DT mapping corrections for Stingray, MMC bus
width fix for RPi Zero W, GPIO LED removal for RPI CM3. Also some
maintainer updates.
- OMAP: Fixlets for display config, interrupt settings for wifi, some
clock/PM pieces. Also IOMMU regression fix and a ti-sysc
no-watchdog regression fix.
- i.MX: A few fixes around PM/settings, some devicetree fixlets and
catching up with config option changes in DRM
- Rockchip: RockRro64 misc DT fixups, Hugsun X99 USB-C, Kevin display
panel settings
... and some smaller fixes for Davinci (backlight, McBSP DMA),
Allwinner (phy regulators, PMU removal on A64, etc)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157
MAINTAINERS: Update the Spreadtrum SoC maintainer
MAINTAINERS: Remove Gregory and Brian for ARCH_BRCMSTB
ARM: dts: bcm2837-rpi-cm3: Avoid leds-gpio probing issue
bus: ti-sysc: Fix watchdog quirk handling
ARM: OMAP2+: Add pdata for OMAP3 ISP IOMMU
ARM: OMAP2+: Plug in device_enable/idle ops for IOMMUs
ARM: davinci_all_defconfig: enable GPIO backlight
ARM: davinci: dm365: Fix McBSP dma_slave_map entry
ARM: dts: bcm2835-rpi-zero-w: Fix bus-width of sdhci
ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM
arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk
ARM: dts: imx7s: Correct GPT's ipg clock source
ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect'
ARM: dts: imx6q-logicpd: Re-Enable SNVS power key
arm64: dts: lx2160a: Correct CPU core idle state name
mailmap: Add Simon Arlott (replacement for expired email address)
arm64: dts: rockchip: Fix override mode for rk3399-kevin panel
...
Fix a ref count, memory leak, and Risc-V cpu schema warnings.
-----BEGIN PGP SIGNATURE-----
iQJEBAABCgAuFiEEktVUI4SxYhzZyEuo+vtdtY28YcMFAl2wtukQHHJvYmhAa2Vy
bmVsLm9yZwAKCRD6+121jbxhwyTdD/4lVzqzzip1CH6yQ4PrNQiSYqMIYhYwnZCJ
uqaq0OdOQGrLFtM4/YbsU+oeTeV+tBHen5k/C3XtwAowH49TQwPZcgFas43eWVqW
/FoWqDPwyB94JjgkAsTbpnieHII7ZSKwMGEuCcHPf6ppOZe2Y9VLgsJWG576kwYe
bZUFJQ7EV+rCaFxWlEYq7kJ1KDPKPIVEqAsULi5TYLRTPPiKUKaYoM525IS+2M0U
NDn9Szvqoy4+ZC2yBn9bBuG6gdwPp0ZlxhRRY/hyjXYn4keC9x0e1rKpvs1DLE+L
Uxbb0OZ7mFWyqLdzptSD1WfghxkhjdGhgwYRJccjkPG+iVDHNAsTTdgPsEBSa4x1
YDnwfkcxkqoYh2tK/TaG7ZGpG5dv7nVhek8IL+bpuvvc9ZdT8mEL6Q86GsKTAEw1
yBzNrEGryZZV62a3xeaNQKQ8v1b3KJXT110UQyZA0yOT/q7k3QcCJ4tfBB4lNdUS
9YLig/llunwyJI+vBMu2M3GuiQy0ClsEPemsm1CIvKEZ5uVMiIzhI5MWu5P/KDJ4
LOYcSYVBtNPhUxMwU0PvIDROJKDTe3g0bVUzarQq+lvsR7muDmmRGvDJT0J6Ziyz
qqMEqRPYsbJoWiE5PgDQIDBaw1wObZ4mjuBvclffyrUiFX2MHk0O0IydzTwM54I/
BEm1DnQGbg==
=vXnQ
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree fixes from Rob Herring:
"A couple more DT fixes for 5.4: fix a ref count, memory leak, and
Risc-V cpu schema warnings"
* tag 'devicetree-fixes-for-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: reserved_mem: add missing of_node_put() for proper ref-counting
of: unittest: fix memory leak in unittest_data_add
dt-bindings: riscv: Fix CPU schema errors
Fix the errors in the RiscV CPU DT schema:
Documentation/devicetree/bindings/riscv/cpus.example.dt.yaml: cpu@0: 'timebase-frequency' is a required property
Documentation/devicetree/bindings/riscv/cpus.example.dt.yaml: cpu@1: 'timebase-frequency' is a required property
Documentation/devicetree/bindings/riscv/cpus.example.dt.yaml: cpu@0: compatible:0: 'riscv' is not one of ['sifive,rocket0', 'sifive,e5', 'sifive,e51', 'sifive,u54-mc', 'sifive,u54', 'sifive,u5']
Documentation/devicetree/bindings/riscv/cpus.example.dt.yaml: cpu@0: compatible: ['riscv'] is too short
Documentation/devicetree/bindings/riscv/cpus.example.dt.yaml: cpu@0: 'timebase-frequency' is a required property
The DT spec allows for 'timebase-frequency' to be in 'cpu' or 'cpus' node
and RiscV requires it in /cpus node, so make it disallowed in cpu
nodes.
Fixes: 4fd669a8c4 ("dt-bindings: riscv: convert cpu binding to json-schema")
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: linux-riscv@lists.infradead.org
Acked-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Rob Herring <robh@kernel.org>
There are a few core fixes here around error handling and handling if
suspend mode configuration and some driver specific fixes here but the
most important change is the fix to the fixed-regulator DT schema
conversion introduced during the last merge window. That fixes one of
the last two errors preventing successful execution of "make dt_binding_check"
which will be enourmously helpful for DT schema development.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl2wgdsTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0PxRB/4uqIJR3n3mIdrHtB0DVaZEWm7jsC6L
PUYZZH//EkLe6d5hgb2qKYrpIJIlKdrVukySl/uyE//gxNH6BUOgggfAGx5qIAjN
qGB6dv+M+AWiDW3hRkMPQ/RnnNgm/llM5cOIHjFqHvYiVbfppIYkKFoCMS8BPWDT
8DUlSwRTGHDKlR1Zn7+HJqvE+eoDAgTVnwoDKaZUh6sL2UrNA8nf0irsB6yq1n+u
1O9D02oTd01tw8Qy3/zAdL+E1RfHbYAuobz367mRUaEzZg6AFG3eWkuJdGIYR+14
C5ypBi/e0zXOyWHEjA5qfxXNbw0U+j4R37iPdgvQvhVQp7D8gIPqXIxX
=r41P
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v5.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"There are a few core fixes here around error handling and handling if
suspend mode configuration and some driver specific fixes here but the
most important change is the fix to the fixed-regulator DT schema
conversion introduced during the last merge window.
That fixes one of the last two errors preventing successful execution
of "make dt_binding_check" which will be enormously helpful for DT
schema development"
* tag 'regulator-fix-v5.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: qcom-rpmh: Fix PMIC5 BoB min voltage
regulator: pfuze100-regulator: Variable "val" in pfuze100_regulator_probe() could be uninitialized
regulator: lochnagar: Add on_off_delay for VDDCORE
regulator: ti-abb: Fix timeout in ti_abb_wait_txdone/ti_abb_clear_all_txdone
regulator: da9062: fix suspend_enable/disable preparation
dt-bindings: fixed-regulator: fix compatible enum
regulator: fixed: Prevent NULL pointer dereference when !CONFIG_OF
regulator: core: make regulator_register() EPROBE_DEFER aware
regulator: of: fix suspend-min/max-voltage parsing
- A fixup for the A10 CSI DT binding merged during the 5.4-rc1 window
- A fix for a dt-binding error
- Addition of phy regulator delays
- The PMU on the A64 was found to be non-functional, so we've dropped it for now
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXa/4RQAKCRDj7w1vZxhR
xU3XAQDYuCixpCCftKIhjcz+oultXqAJysDEE44dATwT1YfINgD/eBSwBw1l/Ni7
yOumUvRZ1fJC3NO8e7vh9cYN9yy5tgw=
=3/ru
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-5.4-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
A number of fixes for this release, but mostly:
- A fixup for the A10 CSI DT binding merged during the 5.4-rc1 window
- A fix for a dt-binding error
- Addition of phy regulator delays
- The PMU on the A64 was found to be non-functional, so we've dropped it for now
* tag 'sunxi-fixes-for-5.4-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun7i: Drop the module clock from the device tree
dt-bindings: media: sun4i-csi: Drop the module clock
media: dt-bindings: Fix building error for dt_binding_check
arm64: dts: allwinner: a64: sopine-baseboard: Add PHY regulator delay
arm64: dts: allwinner: a64: Drop PMU node
arm64: dts: allwinner: a64: pine64-plus: Add PHY regulator delay
Link: https://lore.kernel.org/r/80085a57-c40f-4bed-a9c3-19858d87564e.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
- Handle multiple instances of Intel chips without complaining.
- Restore the Intel Strago DMI workaround
- Make the Armada 37xx handle pins over 32
- Fix the polarity of the LED group on Armada 37xx
- Fix an off-by-one bug in the NS2 driver
- Fix error path for iproc's platform_get_irq()
- Fix error path on the STMFX driver
- Fix a typo in the Berlin AS370 driver
- Fix up misc errors in the Aspeed 2600 BMC support
- Fix a stray SPDX tag
-----BEGIN PGP SIGNATURE-----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=d/2k
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here is a bunch of pin control fixes. I was lagging behind on this
one, some fixes should have come in earlier, sorry about that.
Anyways here it is, pretty straight-forward fixes, the Strago fix
stand out as something serious affecting a lot of machines.
Summary:
- Handle multiple instances of Intel chips without complaining.
- Restore the Intel Strago DMI workaround
- Make the Armada 37xx handle pins over 32
- Fix the polarity of the LED group on Armada 37xx
- Fix an off-by-one bug in the NS2 driver
- Fix error path for iproc's platform_get_irq()
- Fix error path on the STMFX driver
- Fix a typo in the Berlin AS370 driver
- Fix up misc errors in the Aspeed 2600 BMC support
- Fix a stray SPDX tag"
* tag 'pinctrl-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: aspeed-g6: Rename SD3 to EMMC and rework pin groups
pinctrl: aspeed-g6: Fix UART13 group pinmux
pinctrl: aspeed-g6: Make SIG_DESC_CLEAR() behave intuitively
pinctrl: aspeed-g6: Fix I3C3/I3C4 pinmux configuration
pinctrl: aspeed-g6: Fix I2C14 SDA description
pinctrl: aspeed-g6: Sort pins for sanity
dt-bindings: pinctrl: aspeed-g6: Rework SD3 function and groups
pinctrl: berlin: as370: fix a typo s/spififib/spdifib
pinctrl: armada-37xx: swap polarity on LED group
pinctrl: stmfx: fix null pointer on remove
pinctrl: iproc: allow for error from platform_get_irq()
pinctrl: ns2: Fix off by one bugs in ns2_pinmux_enable()
pinctrl: bcm-iproc: Use SPDX header
pinctrl: armada-37xx: fix control of pins 32 and up
pinctrl: cherryview: restore Strago DMI workaround for all versions
pinctrl: intel: Allocate IRQ chip dynamic
Rename SD3 functions and groups to EMMC to better reflect their intended
use before the binding escapes too far into the wild. Also clean up the
SD3 pin groups to eliminate some silliness that slipped through the
cracks (SD3DAT[4-7]) by unifying them into three new groups: EMMCG1,
EMMCG4 and EMMCG8 for 1, 4 and 8-bit data buses respectively.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-2-andrew@aj.id.au
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add retrigger support to Amazon's al-fic driver
- Add SAM9X60 support to Atmel's AIC5 irqchip
- Fix GICv3 maximum interrupt calculation
- Convert SiFive's PLIC to the fasteoi IRQ flow
-----BEGIN PGP SIGNATURE-----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=AV7P
-----END PGP SIGNATURE-----
Merge tag 'irqchip-fixes-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip fixes from Marc Zyngier:
- Add retrigger support to Amazon's al-fic driver
- Add SAM9X60 support to Atmel's AIC5 irqchip
- Fix GICv3 maximum interrupt calculation
- Convert SiFive's PLIC to the fasteoi IRQ flow
Here are some small tty and serial driver fixes for 5.4-rc3 that resolve
a number of reported issues and regressions.
None of these are huge, full details are in the shortlog. THere's also
a MAINTAINERS update that I think you might have already taken in your
tree already, but git should handle that merge easily.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXaH51A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykeBQCeMWoqZHpHTXiadziVgtHrjnj5lL8An2Y+3/Wh
ZbNxvHnUK/VUJQJ2Szsm
=e84r
-----END PGP SIGNATURE-----
Merge tag 'tty-5.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty and serial driver fixes for 5.4-rc3 that
resolve a number of reported issues and regressions.
None of these are huge, full details are in the shortlog. There's also
a MAINTAINERS update that I think you might have already taken in your
tree already, but git should handle that merge easily.
All have been in linux-next with no reported issues"
* tag 'tty-5.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
MAINTAINERS: kgdb: Add myself as a reviewer for kgdb/kdb
tty: serial: imx: Use platform_get_irq_optional() for optional IRQs
serial: fix kernel-doc warning in comments
serial: 8250_omap: Fix gpio check for auto RTS/CTS
serial: mctrl_gpio: Check for NULL pointer
tty: serial: fsl_lpuart: Fix lpuart_flush_buffer()
tty: serial: Fix PORT_LINFLEXUART definition
tty: n_hdlc: fix build on SPARC
serial: uartps: Fix uartps_major handling
serial: uartlite: fix exit path null pointer
tty: serial: linflexuart: Fix magic SysRq handling
serial: sh-sci: Use platform_get_irq_optional() for optional interrupts
dt-bindings: serial: sh-sci: Document r8a774b1 bindings
serial/sifive: select SERIAL_EARLYCON
tty: serial: rda: Fix the link time qualifier of 'rda_uart_exit()'
tty: serial: owl: Fix the link time qualifier of 'owl_uart_exit()'
Here are a lot of small USB driver fixes for 5.4-rc3.
syzbot has stepped up its testing of the USB driver stack, now able to
trigger fun race conditions between disconnect and probe functions.
Because of that we have a lot of fixes in here from Johan and others
fixing these reported issues that have been around since almost all
time.
We also are just deleting the rio500 driver, making all of the syzbot
bugs found in it moot as it turns out no one has been using it for years
as there is a userspace version that is being used instead.
There are also a number of other small fixes in here, all resolving
reported issues or regressions.
All have been in linux-next without any reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXaH78w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk7mACgygFyLQ6GRUTTnGDcohZu44cuMO4AnR/MTrRq
/jiXPRUMsltMV7DHcq+S
=QX4p
-----END PGP SIGNATURE-----
Merge tag 'usb-5.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a lot of small USB driver fixes for 5.4-rc3.
syzbot has stepped up its testing of the USB driver stack, now able to
trigger fun race conditions between disconnect and probe functions.
Because of that we have a lot of fixes in here from Johan and others
fixing these reported issues that have been around since almost all
time.
We also are just deleting the rio500 driver, making all of the syzbot
bugs found in it moot as it turns out no one has been using it for
years as there is a userspace version that is being used instead.
There are also a number of other small fixes in here, all resolving
reported issues or regressions.
All have been in linux-next without any reported issues"
* tag 'usb-5.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (65 commits)
USB: yurex: fix NULL-derefs on disconnect
USB: iowarrior: use pr_err()
USB: iowarrior: drop redundant iowarrior mutex
USB: iowarrior: drop redundant disconnect mutex
USB: iowarrior: fix use-after-free after driver unbind
USB: iowarrior: fix use-after-free on release
USB: iowarrior: fix use-after-free on disconnect
USB: chaoskey: fix use-after-free on release
USB: adutux: fix use-after-free on release
USB: ldusb: fix NULL-derefs on driver unbind
USB: legousbtower: fix use-after-free on release
usb: cdns3: Fix for incorrect DMA mask.
usb: cdns3: fix cdns3_core_init_role()
usb: cdns3: gadget: Fix full-speed mode
USB: usb-skeleton: drop redundant in-urb check
USB: usb-skeleton: fix use-after-free after driver unbind
USB: usb-skeleton: fix NULL-deref on disconnect
usb:cdns3: Fix for CV CH9 running with g_zero driver.
usb: dwc3: Remove dev_err() on platform_get_irq() failure
usb: dwc3: Switch to platform_get_irq_byname_optional()
...
It turns out that what was thought to be the module clock was actually the
clock meant to be used by the sensor, and isn't playing any role with the
CSI controller itself. Let's drop that clock from our binding.
Fixes: c5e8f4ccd7 ("media: dt-bindings: media: Add Allwinner A10 CSI binding")
Reported-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
$id doesn't match the actual filename, so update the $id
Fixes: c5e8f4ccd7 ("media: dt-bindings: media: Add Allwinner A10 CSI binding")
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
RZ/G2N (R8A774B1) SoC also has the R-Car Gen3 compatible SCIF and
HSCIF ports, so document the SoC specific bindings.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1568724324-26995-1-git-send-email-biju.das@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the original bindings that were superseeded by the YAML schemas
didn't mention that phy-names was needed, it turns out that phy-names is
required if phys is set according to phy/phy-bindings.txt.
Let's add back those properties.
Fixes: 14ec072a19 ("dt-bindings: usb: Convert USB HCD generic binding to YAML")
Fixes: c93bcace10 ("dt-bindings: usb: Convert the generic OHCI binding to YAML")
Fixes: c3e2485d5f ("dt-bindings: usb: Convert the generic EHCI binding to YAML")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20191002112651.100504-2-mripard@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Those files got renamed, but another DT file still points to the older
places.
Fixes: 87a55485f2 ("dt-bindings: phy: meson-g12a-usb3-pcie-phy: convert to yaml")
Fixes: da86d286cc ("dt-bindings: phy: meson-g12a-usb2-phy: convert to yaml")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/9ca2d136a1f79c878fff1208f9b536b0b613c0d5.1569330078.git.mchehab+samsung@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb-hcd.txt has been converted to YAML. Update references accordingly.
Fixes: 14ec072a19 ("dt-bindings: usb: Convert USB HCD generic binding to YAML")
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20191003193132.17758-1-j.neuschaefer@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The naming convention for the existing Theobroma boards is
soc-q7module-baseboard, so rk3399-puma-haikou and the in-kernel
devicetrees also follow that scheme.
For some reason in the binding a wrong or outdated naming slipped
in which does not match the used devicetrees and makes the dt-schema
complain now.
Fix this by using the names used in the wild by actual boards.
Fixes: a323a513c7 ("dt-bindings: arm: Convert Rockchip board/soc bindings to json-schema")
[although the issue was also present in the old txt file]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20190917083453.25744-1-heiko@sntech.de
The binding has a typo where resets-names should read reset-names, which in
turn leads to a warning when the example is validated, since reset-names is
being used, and the binding prevent the usage of any property that isn't
described.
Fixes: 088e88be5a ("dt-bindings: phy: add binding for the Lantiq VRX200 and ARX300 PCIe PHYs")
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The example contains an SPI bus and device, but doesn't have the
appropriate size and address cells size.
This creates a DTC warning when the example is compiled since the default
ones will not match what the device uses. Let's add them to remove that
warning.
Fixes: f7356e4703 ("dt-bindings: iio: adc: ad7192: Add binding documentation for AD7192")
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The AD7192 binding describes two regulator properties, avdd-supply and
dvdd-supply, but describes it as a constant string that must be avdd and
dvdd. This is wrong since a *-supply property is actually a phandle, and
results in warnings when the example is validated (or any device tree using
that device, for that matter).
Let's remove that requirement.
Fixes: f7356e4703 ("dt-bindings: iio: adc: ad7192: Add binding documentation for AD7192")
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The linux,rc-map-name property is described using an enum, yet a value has
been put in that enum twice, resulting in a warning. Let's fix that.
Fixes: 7c31b9d673 ("media: dt-bindings: media: Add YAML schemas for the generic RC bindings")
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The fsl,dsp binding requires a memory-region, yet its example doesn't have
one which results in a warning. Let's add a memory-region phandle to the
example.
Fixes: 7db2f2dfc7 ("dt-bindings: dsp: fsl: Add DSP core binding support")
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Pull networking fixes from David Miller:
1) Sanity check URB networking device parameters to avoid divide by
zero, from Oliver Neukum.
2) Disable global multicast filter in NCSI, otherwise LLDP and IPV6
don't work properly. Longer term this needs a better fix tho. From
Vijay Khemka.
3) Small fixes to selftests (use ping when ping6 is not present, etc.)
from David Ahern.
4) Bring back rt_uses_gateway member of struct rtable, it's semantics
were not well understood and trying to remove it broke things. From
David Ahern.
5) Move usbnet snaity checking, ignore endpoints with invalid
wMaxPacketSize. From Bjørn Mork.
6) Missing Kconfig deps for sja1105 driver, from Mao Wenan.
7) Various small fixes to the mlx5 DR steering code, from Alaa Hleihel,
Alex Vesker, and Yevgeny Kliteynik
8) Missing CAP_NET_RAW checks in various places, from Ori Nimron.
9) Fix crash when removing sch_cbs entry while offloading is enabled,
from Vinicius Costa Gomes.
10) Signedness bug fixes, generally in looking at the result given by
of_get_phy_mode() and friends. From Dan Crapenter.
11) Disable preemption around BPF_PROG_RUN() calls, from Eric Dumazet.
12) Don't create VRF ipv6 rules if ipv6 is disabled, from David Ahern.
13) Fix quantization code in tcp_bbr, from Kevin Yang.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (127 commits)
net: tap: clean up an indentation issue
nfp: abm: fix memory leak in nfp_abm_u32_knode_replace
tcp: better handle TCP_USER_TIMEOUT in SYN_SENT state
sk_buff: drop all skb extensions on free and skb scrubbing
tcp_bbr: fix quantization code to not raise cwnd if not probing bandwidth
mlxsw: spectrum_flower: Fail in case user specifies multiple mirror actions
Documentation: Clarify trap's description
mlxsw: spectrum: Clear VLAN filters during port initialization
net: ena: clean up indentation issue
NFC: st95hf: clean up indentation issue
net: phy: micrel: add Asym Pause workaround for KSZ9021
net: socionext: ave: Avoid using netdev_err() before calling register_netdev()
ptp: correctly disable flags on old ioctls
lib: dimlib: fix help text typos
net: dsa: microchip: Always set regmap stride to 1
nfp: flower: fix memory leak in nfp_flower_spawn_vnic_reprs
nfp: flower: prevent memory leak in nfp_flower_spawn_phy_reprs
net/sched: Set default of CONFIG_NET_TC_SKB_EXT to N
vrf: Do not attempt to create IPv6 mcast rule if IPv6 is disabled
net: sched: sch_sfb: don't call qdisc_put() while holding tree lock
...
Besides one new driver being added for the PWM controller found in
various Spreadtrum SoCs, this series of changes brings a slew of, mostly
minor, fixes and cleanups for existing drivers, as well as some
enhancements to the core code.
Lastly, Uwe is added to the PWM subsystem entry of the MAINTAINERS file,
making official his role as a reviewer.
-----BEGIN PGP SIGNATURE-----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=C9sW
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Besides one new driver being added for the PWM controller found in
various Spreadtrum SoCs, this series of changes brings a slew of,
mostly minor, fixes and cleanups for existing drivers, as well as some
enhancements to the core code.
Lastly, Uwe is added to the PWM subsystem entry of the MAINTAINERS
file, making official his role as a reviewer"
* tag 'pwm/for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (34 commits)
MAINTAINERS: Add myself as reviewer for the PWM subsystem
MAINTAINERS: Add patchwork link for PWM entry
MAINTAINERS: Add a selection of PWM related keywords to the PWM entry
pwm: mediatek: Add MT7629 compatible string
dt-bindings: pwm: Update bindings for MT7629 SoC
pwm: mediatek: Update license and switch to SPDX tag
pwm: mediatek: Use pwm_mediatek as common prefix
pwm: mediatek: Allocate the clks array dynamically
pwm: mediatek: Remove the has_clks field
pwm: mediatek: Drop the check for of_device_get_match_data()
pwm: atmel: Consolidate driver data initialization
pwm: atmel: Remove unneeded check for match data
pwm: atmel: Remove platform_device_id and use only dt bindings
pwm: stm32-lp: Add check in case requested period cannot be achieved
pwm: Ensure pwm_apply_state() doesn't modify the state argument
pwm: fsl-ftm: Don't update the state for the caller of pwm_apply_state()
pwm: sun4i: Don't update the state for the caller of pwm_apply_state()
pwm: rockchip: Don't update the state for the caller of pwm_apply_state()
pwm: Let pwm_get_state() return the last implemented state
pwm: Introduce local struct pwm_chip in pwm_apply_state()
...
Pull thermal management updates from Zhang Rui:
- Add Amit Kucheria as thermal subsystem Reviewer (Amit Kucheria)
- Fix a use after free bug when unregistering thermal zone devices (Ido
Schimmel)
- Fix thermal core framework to use put_device() when device_register()
fails (Yue Hu)
- Enable intel_pch_thermal and MMIO RAPL support for Intel Icelake
platform (Srinivas Pandruvada)
- Add clock operations in qorip thermal driver, for some platforms with
clock control like i.MX8MQ (Anson Huang)
- A couple of trivial fixes and cleanups for thermal core and different
soc thermal drivers (Amit Kucheria, Christophe JAILLET, Chuhong Yuan,
Fuqian Huang, Kelsey Skunberg, Nathan Huckleberry, Rishi Gupta,
Srinivas Kandagatla)
* 'for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
MAINTAINERS: Add Amit Kucheria as reviewer for thermal
thermal: Add some error messages
thermal: Fix use-after-free when unregistering thermal zone device
thermal/drivers/core: Use put_device() if device_register() fails
thermal_hwmon: Sanitize thermal_zone type
thermal: intel: Use dev_get_drvdata
thermal: intel: int3403: replace printk(KERN_WARN...) with pr_warn(...)
thermal: intel: int340x_thermal: Remove unnecessary acpi_has_method() uses
thermal: int340x: processor_thermal: Add Ice Lake support
drivers: thermal: qcom: tsens: Fix memory leak from qfprom read
thermal: tegra: Fix a typo
thermal: rcar_gen3_thermal: Replace devm_add_action() followed by failure action with devm_add_action_or_reset()
thermal: armada: Fix -Wshift-negative-value
dt-bindings: thermal: qoriq: Add optional clocks property
thermal: qoriq: Use __maybe_unused instead of #if CONFIG_PM_SLEEP
thermal: qoriq: Use devm_platform_ioremap_resource() instead of of_iomap()
thermal: qoriq: Fix error path of calling qoriq_tmu_register_tmu_zone fail
thermal: qoriq: Add clock operations
drivers: thermal: processor_thermal_device: Export sysfs interface for TCC offset
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAl2NtDQACgkQ+iyteGJfRsoHgQCdGLeQMm4IR3jsDdFQk/eTIGfR
eNIAoN8AY1UTFvWJTxEOhucdAzEAVnHs
=TdeQ
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-5.4-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- addition of AST2600, i.MX7ULP and F81803 watchdog support
- removal of the w90x900 and ks8695 drivers
- ziirave_wdt improvements
- small fixes and improvements
* tag 'linux-watchdog-5.4-rc1' of git://www.linux-watchdog.org/linux-watchdog: (51 commits)
watchdog: f71808e_wdt: Add F81803 support
watchdog: qcom: remove unnecessary variable from private storage
watchdog: qcom: support pre-timeout when the bark irq is available
watchdog: imx_sc: this patch just fixes whitespaces
watchdog: apseed: Add access_cs0 option for alt-boot
watchdog: aspeed: add support for dual boot
watchdog: orion_wdt: use timer1 as a pretimeout
watchdog: Add i.MX7ULP watchdog support
dt-bindings: watchdog: Add i.MX7ULP bindings
dt-bindings: watchdog: sun4i: Add the watchdog clock
dt-bindings: watchdog: sun4i: Add the watchdog interrupts
dt-bindings: watchdog: Convert Allwinner watchdog to a schema
dt-bindings: watchdog: Add YAML schemas for the generic watchdog bindings
watchdog: aspeed: Add support for AST2600
dt-bindings: watchdog: Add ast2600 compatible
watchdog: ziirave_wdt: Update checked I2C functionality mask
watchdog: ziirave_wdt: Drop ziirave_firm_write_block_data()
watchdog: ziirave_wdt: Fix DOWNLOAD_START payload
watchdog: ziirave_wdt: Drop status polling code
watchdog: ziirave_wdt: Fix RESET_PROCESSOR payload
...
Document RZ/G2N (R8A774B1) SoC bindings.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull i2c updates from Wolfram Sang:
- new driver for ICY, an Amiga Zorro card :)
- axxia driver gained slave mode support, NXP driver gained ACPI
- the slave EEPROM backend gained 16 bit address support
- and lots of regular driver updates and reworks
* 'i2c/for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (52 commits)
i2c: tegra: Move suspend handling to NOIRQ phase
i2c: imx: ACPI support for NXP i2c controller
i2c: uniphier(-f): remove all dev_dbg()
i2c: uniphier(-f): use devm_platform_ioremap_resource()
i2c: slave-eeprom: Add comment about address handling
i2c: exynos5: Remove IRQF_ONESHOT
i2c: stm32f7: Make structure stm32f7_i2c_algo constant
i2c: cht-wc: drop check because i2c_unregister_device() is NULL safe
i2c-eeprom_slave: Add support for more eeprom models
i2c: fsi: Add of_put_node() before break
i2c: synquacer: Make synquacer_i2c_ops constant
i2c: hix5hd2: Remove IRQF_ONESHOT
i2c: i801: Use iTCO version 6 in Cannon Lake PCH and beyond
watchdog: iTCO: Add support for Cannon Lake PCH iTCO
i2c: iproc: Make bcm_iproc_i2c_quirks constant
i2c: iproc: Add full name of devicetree node to adapter name
i2c: piix4: Add ACPI support
i2c: piix4: Fix probing of reserved ports on AMD Family 16h Model 30h
i2c: ocores: use request_any_context_irq() to register IRQ handler
i2c: designware: Fix optional reset error handling
...
Remove 'const:' in the compatible enum. This was breaking
make dt_binding_check since it has more than one compatible string.
Fixes: 9c86d003d6 ("dt-bindings: regulator: add regulator-fixed-clock binding")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Link: https://lore.kernel.org/r/20190923081840.23391-1-philippe.schenker@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>