1) Minor trivial refactoring and improvements
2) Check for unsupported parameters fields in SW steering
3) Support TC offload for OVS internal port, from Ariel, see below.
Ariel Levkovich says:
=====================
Support HW offload of TC rules involving OVS internal port
device type as the filter device or the destination
device.
The support is for flows which explicitly use the internal
port as source or destination device as well as indirect offload
for flows performing tunnel set or unset via a tunnel device
and the internal port is the tunnel overlay device.
Since flows with internal port as source port are added
as egress rules while redirecting to internal port is done
as an ingress redirect, the series introduces the necessary
changes in mlx5_core driver to support the new types of flows
and actions.
=====================
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmF8X0sACgkQSD+KveBX
+j5PsQf/RfsE+spW0yJriJQ6Et+o+/CYR+AQYat5MaXjRw8uMz6uBcfXWCIBbYjw
OwNP4ZagWXIHMkelj2Ap0Qlu4yqkUBy1A0le7HcAzOeje1vc9BObS15w9pJvQ9cp
br3ZK5VZnQccSfF/LQpSjlGhD9083kETA2uXlCz7vitn8MVaya6ue6GU+wFC4Wnz
LjOJ4PMXCEfhpA+efD0nD4EK6FJjqvJoVQkxWNmgOW7yg5PcyWXZD/tsDZUI8DGl
0GlnM6W2H8bC0YhW01cnOsWPU+vtMLCsaF0YKqsLhnWUsaYSD5lXPIHqH6VpucZ7
LSv/c2U9pBnWkf7UoFyuEeQxAhz1rg==
=Uxa9
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2021-10-29' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2021-10-29
1) Minor trivial refactoring and improvements
2) Check for unsupported parameters fields in SW steering
3) Support TC offload for OVS internal port, from Ariel, see below.
Ariel Levkovich says:
=====================
Support HW offload of TC rules involving OVS internal port
device type as the filter device or the destination
device.
The support is for flows which explicitly use the internal
port as source or destination device as well as indirect offload
for flows performing tunnel set or unset via a tunnel device
and the internal port is the tunnel overlay device.
Since flows with internal port as source port are added
as egress rules while redirecting to internal port is done
as an ingress redirect, the series introduces the necessary
changes in mlx5_core driver to support the new types of flows
and actions.
=====================
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
br_switchdev_mdb_notify() is conditionally compiled only when
CONFIG_NET_SWITCHDEV=y and CONFIG_BRIDGE_IGMP_SNOOPING=y. It is called
from br_mdb.c, which is conditionally compiled only when
CONFIG_BRIDGE_IGMP_SNOOPING=y.
The shim definition of br_switchdev_mdb_notify() is therefore needed for
the case where CONFIG_NET_SWITCHDEV=n, however we mistakenly put it
there for the case where CONFIG_BRIDGE_IGMP_SNOOPING=n. This results in
build failures when CONFIG_BRIDGE_IGMP_SNOOPING=y and
CONFIG_NET_SWITCHDEV=n.
To fix this, put the shim definition right next to
br_switchdev_fdb_notify(), which is properly guarded by NET_SWITCHDEV=n.
Since this is called only from br_mdb.c, we need not take any extra
safety precautions, when NET_SWITCHDEV=n and BRIDGE_IGMP_SNOOPING=n,
this shim definition will be absent but nobody will be needing it.
Fixes: 9776457c78 ("net: bridge: mdb: move all switchdev logic to br_switchdev.c")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211029223606.3450523-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2021-10-29
This series contains updates to igc driver only.
Sasha removes an unnecessary media type check, adds a new device ID, and
changes a device reset to a port reset command.
====================
Link: https://lore.kernel.org/r/20211029174101.2970935-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
40GbE Intel Wired LAN Driver Updates 2021-10-29
This series contains updates to i40e, ice, igb, and ixgbevf drivers.
Yang Li simplifies return statements of bool values for i40e and ice.
Jan Kundrát corrects problems with I2C bit-banging for igb.
Colin Ian King removes unneeded variable initialization for ixgbevf.
====================
Link: https://lore.kernel.org/r/20211029164641.2714265-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When performing route device lookup for decap action, support
the case of ovs internal port as the lookup result.
In such case, an internal port struct is mapped and attached
to the flow attributes so that the source port matching of the
rule will match on the internal port's metadata value.
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Adjust termination table logic to handle rules which
involve internal port as filter or forwarding device.
For cases where the rule forwards from internal port
to uplink, always choose to go via termination table.
This is because it is not known from where the packet
originally arrived to the internal port and it is possible
that it came from the uplink itself, in which case
a term table is required to perform hairpin.
If the packet arrived from a vport, going via term
table has no effect.
For cases where the rule forwards to an internal port
from uplink the rep pointer will point to the uplink rep,
avoid going via termination table as it is not required.
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Register callbacks for tc blocks of ovs internal port devices.
This allows an indirect offloading rules that apply on
such devices as the filter device.
In case a rule is added to a tc block of an internal port,
the mlx5 driver will implicitly add a matching on the internal
port's unique vport metadata value to the rule's matching list.
Therefore, only packets that previously hit a rule that redirects
to an internal port and got the vport metadata overwritten to the
internal port's unique metadata, can match on such indirect rule.
Offloading of both ingress and egress tc blocks of internal ports
is supported as opposed to other devices where only ingress block
offloading is supported.
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When pefroming encap action, a route lookup is performed
to find the routing device the packet should be forwarded
to after the encapsulation. This is the device that has the
local tunnel ip address.
This change adds support to offload an encap rule where the
route device ends up being an ovs internal port.
In such case, the driver will add a HW rule that will encapsulate
the packet with the tunnel header and will overwrite the vport
metadata in reg_c0 to the internal port metadata value.
Finally, the packet will be forwarded to the root table to be
processed again with the indication that it came from an internal
port.
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Allow offloading rules that redirect to ovs internal port
ingress and egress.
To support redirect to ingress device, offloading of REDIRECT_INGRESS
action is added.
When a tc rule redirects to ovs internal port, the hw rule will
overwrite the input vport value in reg_c0 with a new vport metadata
value that is mapped for this internal port using the internal
port mapping api that is introduce in previous patches.
After that the hw rule will redirect the packet to the root table
to continue processing with the new vport metadata value.
The new vport metadata value indicates that this packet is now
arriving through an internal port and therefore should be processed
using rules that apply on the same internal port as the filter device.
Therefore, following rules that apply on this internal port will have
to match on the same vport metadata value as part of their matching
keys to make sure the packet belongs to the internal port.
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Setting the skb packet type field to host is usually
done when performing forwarding to ingress device.
This is required since the receive handling that is used
by the redirect to ingress action checks whether the packet
doesn't belong to this host and drops the packet in such case.
In order to be able to offload action redirect ingress, tc offload
code needs to accept the skbedit ptype action as well.
There's no special handling in HW for such action since it will
be followed by a redirect action and therefore, this code
only allows us to accept such action in the actions list but
not performing anything specific in HW for it.
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Adding infrastructure to map ovs internal port device to vport
match metadata to support offload of rules with internal port as
the filter device or as the destination device.
The infrastructure allows adding and removing internal port device
to an eswitch database and getting a unique vport metadata value to
be placed and match on in reg_c0 when offloading rules that are coming
from or going to an internal port.
The new int port metadata can be written to the source port register
in HW to indicate that current source port of the packet is the
internal port and not one of the actual HW vports (uplink or VF).
Using this method, it is possible to offload TC rules with an OVS
internal port as their destination port (overwriting the src vport
register) or as the filter port (matching on the value of the src
vport register and making sure it matches to the internal port's
value).
There is also a need to handle a miss case where the packet's
src port value was changed in HW to an internal port but a following
rule which matches on this new src port value wasn't found in HW.
In such case, the packet will be forwarded to the driver with
metadata which allows driver to restore the info of the internal
port's netdevice. Once this info is restored, the uplink driver
can forward the packet to the relevant netdevice in SW.
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Rename tun_dev to fwd_dev within mlx5e_tc_update_priv struct
since future implementation may introduce other device types
which the handler is forwarding to.
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Move the ownership of skb forwarding to network stack to the
tc update_skb handler as different cases will require different
handling of the skb.
While the tc handler will take care of the various cases and
properly handle the handover of the skb to the network stack
and freeing the skb, the main rx handler will be kept clean
from branches and usage of flags.
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When a matcher is being built, we "consume" (clear) mask fields one by one,
and to verify that we do support all the required fields we check if the
whole mask was consumed, else the matching request includes unsupported
fields.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
CT creates a counter for each CT rule, and for each such counter,
fs_counters tries to queue mlx5_fc_stats_work() work again via
mod_delayed_work(0) call to refresh all counters. This call has a
large performance impact when reaching high insertion rate and
accounts for ~8% of the insertion time when using software steering.
Allow skipping the refresh of all counters during counter creation.
Change CT to use this refresh skipping for it's counters.
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Part of code that is related solely to IPsec is always compiled in the
driver code regardless if the IPsec functionality is enabled or disabled
in the driver code, this will add unnecessary branch in case IPsec is
disabled at Tx data path.
Move IPsec related code to IPsec related file such that in case of IPsec
is disabled and because of unlikely macro the compiler should be able to
optimize and omit the checksum IPsec code all together from Tx data path
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Emeel Hakim <ehakim@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
ignore_flow_level isn't supported for VFs, and so it causes
post_act and ct to warn about it.
Instead of disabling CT for VFs, and a driver update will be need
to enable CT again once firmware support this, remove this warning
specifically for VFs. This way, it could be automatically enabled on
future firmwares where VFs support ignore_flow_level capability.
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Clang warns:
drivers/net/ethernet/mellanox/mlx5/core/en/tc/sample.c:635:34: error: variable 'esw' is uninitialized when used here [-Werror,-Wuninitialized]
mlx5_eswitch_del_offloaded_rule(esw, sample_flow->pre_rule, sample_flow->pre_attr);
^~~
drivers/net/ethernet/mellanox/mlx5/core/en/tc/sample.c:626:26: note: initialize the variable 'esw' to silence this warning
struct mlx5_eswitch *esw;
^
= NULL
1 error generated.
It appears that the assignment should have been shuffled instead of
removed outright like in mlx5e_tc_sample_offload(). Add it back so there
is no use of esw uninitialized.
Fixes: a64c5edbd2 ("net/mlx5: Remove unnecessary checks for slow path flag")
Link: https://github.com/ClangBuiltLinux/linux/issues/1494
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The _reset_hw_base method switched from port reset (CTRL[26]) to device
reset (CTRL[29]) since the FW was receiving an interrupt on CTRL[29].
FW code was later modified to also receive an interrupt on CTRL[26].
Since certain HW values are not reset to default by CTRL[29], we go back
to CTRL[26] for the HW reset, as it meets all current requirements.
This reverts commit bb4265ec24 ("igc: Update the MAC reset flow").
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add new device ID for the next step of the silicon and
reflect the I226_LMVP part.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i225 devices only have copper phy media type. There is no point in
checking phy media type during the phy initialization. This patch cleans
up a pointless check.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The variable ret_val is being initialized with a value that is never
read, it is being updated later on. The assignment is redundant and
can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver tried to use Linux' native software I2C bus master
(i2c-algo-bits) for exporting the I2C interface that talks to the SFP
cage(s) towards userspace. As-is, however, the physical SCL/SDA pins
were not moving at all, staying at logical 1 all the time.
The main culprit was the I2CPARAMS register where igb was not setting
the I2CBB_EN bit. That meant that all the careful signal bit-banging was
actually not being propagated to the chip pads (I verified this with a
scope).
The bit-banging was not correct either, because I2C is supposed to be an
open-collector bus, and the code was driving both lines via a totem
pole. The code was also trying to do operations which did not make any
sense with the i2c-algo-bits, namely manipulating both SDA and SCL from
igb_set_i2c_data (which is only supposed to set SDA). I'm not sure if
that was meant as an optimization, or was just flat out wrong, but given
that the i2c-algo-bits is set up to work with a totally dumb GPIO-ish
implementation underneath, there's no need for this code to be smart.
The open-drain vs. totem-pole is fixed by the usual trick where the
logical zero is implemented via regular output mode and outputting a
logical 0, and the logical high is implemented via the IO pad configured
as an input (thus floating), and letting the mandatory pull-up resistors
do the rest. Anything else is actually wrong on I2C where all devices
are supposed to have open-drain connection to the bus.
The missing I2CBB_EN is set (along with a safe initial value of the
GPIOs) just before registering this software I2C bus.
The chip datasheet mentions HW-implemented I2C transactions (SFP EEPROM
reads and writes) as well, but I'm not touching these for simplicity.
Tested on a LR-Link LRES2203PF-2SFP (which is an almost-miniPCIe form
factor card, a cable, and a module with two SFP cages). There was one
casualty, an old broken SFP we had laying around, which was used to
solder some thin wires as a DIY I2C breakout. Thanks for your service.
With this patch in place, I can `i2cdump -y 3 0x51 c` and read back data
which make sense. Yay.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
See-also: https://www.spinics.net/lists/netdev/msg490554.html
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the following coccicheck warning:
./drivers/net/ethernet/intel/i40e/i40e_xsk.c:229:35-40: WARNING:
conversion to bool not needed here
./drivers/net/ethernet/intel/ice/ice_xsk.c:399:35-40: WARNING:
conversion to bool not needed here
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fourth set of patches for v5.16. Mostly fixes this time, wcn36xx and
iwlwifi have some new features but nothing really out of ordinary. We
have one conflict with kspp tree.
Conflicts:
kspp tree has a conflict in drivers/net/wireless/intel/iwlwifi/fw/api/tx.h:
https://lkml.kernel.org/r/20211028192934.01520d7e@canb.auug.org.au
Major changes:
ath11k
* fix QCA6390 A-MSDU handling (CVE-2020-24588)
wcn36xx
* enable hardware scan offload for 5Ghz band
* add missing 5GHz channels 136 and 144
iwlwifi
* support a new ACPI table revision
* improvements in the device selection code
* new hardware support
* support for WiFi 6E enablement via BIOS
* support firmware API version 67
* support for 160MHz in ranging measurements
-----BEGIN PGP SIGNATURE-----
iQFJBAABCgAzFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmF7+wUVHGt2YWxvQGNv
ZGVhdXJvcmEub3JnAAoJEG4XJFUm622bRGoH/0XrfEwzH4iR3j/xRPTBMJjBZO/Z
ZN0PQ2L8402c7iG9M0psSFOdqFe8vtKzuuV367ifQzwmGFoQIzAckL9nCA1yFUBg
EXF3nP0/mb8R0w6rzjkLUQ9EejLLeX35Kh6B1oLgglPdLvE+Yv6/Iqs1yOHwHZFF
RBHqyBc9YcQBuhah4JPqIXr8tUCkRgWwK/VvCwhoGDWimBlH7LhgOHTFQhVJ+Z8b
/RsLS2iIv4wGkiQX9cwilmX3QSz/jK0od1FXHW347v+nm96Fs3d2F1juAyhE6io2
xN1qzEU4SQ90byxhCsBOvZC6JTpRJvw49XME76MrzaLP+FuZ8I2zdAe7wd8=
=Y1xX
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-10-29' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.16
Fourth set of patches for v5.16. Mostly fixes this time, wcn36xx and
iwlwifi have some new features but nothing really out of ordinary.
We have one conflict with kspp tree.
Major changes:
ath11k
* fix QCA6390 A-MSDU handling (CVE-2020-24588)
wcn36xx
* enable hardware scan offload for 5Ghz band
* add missing 5GHz channels 136 and 144
iwlwifi
* support a new ACPI table revision
* improvements in the device selection code
* new hardware support
* support for WiFi 6E enablement via BIOS
* support firmware API version 67
* support for 160MHz in ranging measurements
====================
Link: https://lore.kernel.org/r/20211029134707.DE2B0C4360D@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver no longer depends on this option, but it fails to
build if it's disabled because the skb->tc_skip_classify is
hidden behind an #ifdef:
drivers/net/ifb.c:81:8: error: no member named 'tc_skip_classify' in 'struct sk_buff'
skb->tc_skip_classify = 1;
Use the same #ifdef around the assignment.
Fixes: 046178e726 ("ifb: Depend on netfilter alternatively to tc")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add firmware (FW) version 4.0 support for Marvell Prestera
driver.
Major changes have been made to new v4.0 FW ABI to add support
of new features, introduce the stability of the FW ABI and ensure
better forward compatibility for the future driver vesrions.
Current v4.0 FW feature set support does not expect any changes
to ABI, as it was defined and tested through long period of time.
The ABI may be extended in case of new features, but it will not
break the backward compatibility.
ABI major changes done in v4.0:
- L1 ABI, where MAC and PHY API configuration are split.
- ACL has been split to low-level TCAM and Counters ABI
to provide more HW ACL capabilities for future driver
versions.
To support backward support, the addition compatibility layer is
required in the driver which will have two different codebase under
"if FW-VER elif FW-VER else" conditions that will be removed
in the future anyway, So, the idea was to break backward support
and focus on more stable FW instead of supporting old version
with very minimal and limited set of features/capabilities.
Improve FW msg validation:
* Use __le64, __le32, __le16 types in msg to/from FW to
catch endian mismatch by sparse.
* Use BUILD_BUG_ON for structures sent/recv to/from FW.
Co-developed-by: Vadym Kochan <vkochan@marvell.com>
Signed-off-by: Vadym Kochan <vkochan@marvell.com>
Signed-off-by: Yevhen Orlov <yevhen.orlov@plvision.eu>
Signed-off-by: Taras Chornyi <tchornyi@marvell.com>
Signed-off-by: Volodymyr Mytnyk <vmytnyk@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devlink_alloc() and devlink_register() are both GPL.
A non-GPL module won't get far, so for consistency
we can make all symbols GPL without risking any real
life breakage.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both !data[IFLA_BAREUDP_PORT] and !data[IFLA_BAREUDP_ETHERTYPE] are
checked. We should remove the checks of data[IFLA_BAREUDP_PORT] and
data[IFLA_BAREUDP_ETHERTYPE] that follow since they are always true.
Put both statements together in group and balance the space on both
sides of '=' sign.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove additional character in the source to properly indent if branch.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase the rx ring size (LAN743X_RX_RING_SIZE) to improve rx performance on some platforms.
Tested on x86 PC with EVB-LAN7430.
The iperf3.7 TCPIP improved from 881 Mbps to 922 Mbps, and UDP improved from 817 Mbps to 936 Mbps.
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeremy Kerr says:
====================
MCTP flow support
For certain MCTP transport bindings, the binding driver will need to be
aware of request/response pairing. For example, the i2c binding may need
to set multiplexer configuration when expecting a response from a device
behind a mux.
This series implements a mechanism for informing the driver about these
flows, so it can implement transport-specific behaviour when a flow is
in progress (ie, a response is expected, and/or we time-out on that
expectation). We use a skb extension to notify the driver about the
presence of a flow, and a new dev->ops callback to notify about a flow's
destruction.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have an extension for MCTP data in skbs, populate the flow
when a key has been created for the packet, and add a device driver
operation to inform of flow destruction.
Includes a fix for a warning with test builds:
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds a new skb extension for MCTP, to represent a
request/response flow.
The intention is to use this in a later change to allow i2c controllers
to correctly configure a multiplexer over a flow.
Since we have a cleanup function in the core path (if an extension is
present), we'll need to make CONFIG_MCTP a bool, rather than a tristate.
Includes a fix for a build warning with clang:
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a future change, we will want the key available for future use after
allocating a new tag. This change returns the key from
mctp_alloc_local_tag, rather than just key->tag.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
arch, misc: use eth_hw_addr_set()
Convert remaining misc drivers to use helpers to write
to netdev->dev_addr.
This is the last set :) :)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it go through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it go through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it go through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-10-28
This series contains updates to ice driver only.
Michal adds support for eswitch drop and redirect filters from and to
tunnel devices. From meaning from uplink to VF and to means from VF to
uplink. This is accomplished by adding support for indirect TC tunnel
notifications and adding appropriate training packets and match fields
for UDP tunnel headers. He also adds returning virtchannel responses for
blocked operations as returning a response is still needed.
Marcin sets netdev min and max MTU values on port representors to allow
for MTU changes over default values.
Brett adds detecting and reporting of PHY firmware load issues for devices
which support this.
Nathan Chancellor fixes a clang warning for implicit fallthrough.
Wang Hai fixes a return value for failed allocation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
All SoCs with this IP core support 8 burst length. Hauke
suggested to hardcode this value and simplify the driver.
Link: https://lkml.org/lkml/2021/9/14/1533
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
All SoCs with this IP core support 8 burst length. Hauke
suggested to hardcode this value and simplify the driver.
Link: https://lkml.org/lkml/2021/9/14/1533
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: devlink enhancements
This patch series implements some devlink enhancements for bnxt_en.
They include:
1. devlink reload to reinitialize driver or to activate new firmware.
2. Support enable_remote_dev_reset to enable/disable other functions
resetting the device.
3. Consolidate and improve the health reporters.
4. Support live firmware patch.
5. Provide devlink dev info "fw" version on older firmware.
v2:
In patch 3, don't use devlink_reload_disable() and devlink_reload_enable()
which are no longer available in the latest kernel. Instead, check that
the netdev is not in unregistered state before proceeding with reload.
In patch 14, use min_t() instead of min() to fix the mismatched type
warning.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 'enable_remote_dev_reset' documentation to bnxt.rst.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On older firmware that doesn't support the HWRM_NVM_GET_DEV_INFO
command that returns detailed stored firmware versions, fallback
to use the same firmware package version that is reported to ethtool.
Refactor bnxt_get_pkgver() in bnxt_ethtool.c so that devlink can call
and get the package version.
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Live patches are activated by using the 'limit no_reset' option when
performing a devlink dev reload fw_activate operation. These packages
must first be installed on the device in the usual way. For example,
via devlink dev flash or ethtool -f.
The devlink device info has also been enhanced to render stored and
running live patch versions.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main changes are firmware live patch support and 2 additional FEC
standard counters.
Add the matching FEC counters to ethtool counter array. Firmware older
than 220 does not return the proper size of the extended RX counters so
we need to cap it at the smaller legacy size. Otherwise the new FEC
counters may show up with garbage values.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the dump with firmware 'live' coredump data. This includes
the information stored in NVRAM by the firmware exception handler
prior to recovery. Thus, the live dump includes the desired crash
context.
Firmware does not support HWRM calls after RESET_NOTIFY, so there is
no supported way to capture a coredump during the auto dump phase.
Detect this and abort when called from devlink_health_report().
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
