In case of error, the function devm_ioremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 78b4af312f ("clk: meson-axg: add clock controller drivers")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
"rem * SDM_DEN" can easily overflow on the 32-bit Meson8 and Meson8b
SoCs if the "remainder" (after the division operation) is greater than
262143Hz. This is likely to happen since the input clock for the MPLLs
on Meson8 and Meson8b is "fixed_pll", which is running at a rate of
2550MHz.
One example where this was observed to be problematic was the Ethernet
clock calculation (which takes MPLL2 as input). When requesting a rate
of 125MHz there is a remainder of 2500000Hz.
The resulting MPLL2 rate before this patch was 127488329Hz.
The resulting MPLL2 rate after this patch is 124999103Hz.
Commit b609338b26 ("clk: meson: mpll: use 64bit math in
rate_from_params") already fixed a similar issue in rate_from_params.
Fixes: 007e6e5c5f ("clk: meson: mpll: add rw operation")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Make the spinlock more specific, so better for lockdep
debugging and ctags/grep.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Remove CLK_IGNORE_UNUSED from mmc clocks. This was only needed while the
mmc driver incorrectly used the xtal as source instead of the mmc
clock. Now, the driver takes the correct clock, CCF is aware that the
clock is being used and we can remove this flag.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
According to the datasheet, in Meson-GXBB/GXL series,
The clock gate bit for SARADC is HHI_GCLK_MPEG2 bit[22],
while clock gate bit for SANA is HHI_GCLK_MPEG0 bit[10].
Test passed at gxl-s905x-p212 board.
The following published datasheets are wrong and should be updated
[1] GXBB v1.1.4
[2] GXL v0.3_20170314
Fixes: 738f66d321 ("clk: gxbb: add AmLogic GXBB clk controller driver")
Tested-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The Amlogic Meson GX SoCs needs these two clocks to power up the
VPU power domain.
These two clocks are similar to the MALI clocks by having a glitch-free
mux and two similar clocks with gate, divider and muxes.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: removed the CLK_IGNORE_UNUSED on muxes and dividers]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the clkids for the clocks feeding the Video Processing Unit.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The CEC 32K AO Clock is a dual divider with dual counter to provide a more
precise 32768Hz clock for the CEC subsystem from the external xtal.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Switch the aoclk driver to use the new bindings and switch all the
registers access to regmap only.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Input source 0 of the mmc controllers is not directly xtal, as currently
described in DT. Each controller is fed by a composite clock (the usual
mux, divider and gate). The muxes inputs are the xtal (default) and the
fclk_div clocks. These parents, along with the divider, should be able to
provide the necessary rates for mmc and nand operation.
The input muxes should also be able to take mpll2, mpll3 and gp0_pll but
these are precious clocks, needed for other usage. It is better if the
mmc does not use these them. For this reason, mpll2, mpll3 and gp0_pll is
not listed among the possible parents.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
CLK_DIVIDER_ROUND_CLOSEST was incorrectly put in the hw.init flags
while it should have been in the divider flags
Fixes: 3c277c247e ("clk: meson: gxbb: add cts_mclk_i958")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
CLK_DIVIDER_ROUND_CLOSEST was incorrectly put in the hw.init flags
while it should have been in the divider flags
Fixes: 4087bd4b21 ("clk: meson: gxbb: add cts_amclk")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The clock controller also includes some reset lines. This patch
implements a reset controller to assert and de-assert these resets.
The reset controller itself is registered early (through
CLK_OF_DECLARE_DRIVER) because it is needed very early in the boot
process (to start the secondary CPU cores).
According to the public S805 datasheet there are two more reset bits
in the HHI_SYS_CPU_CLK_CNTL0 register, which are not implemented by
this patch (as these seem to be unused in Amlogic's vendor Linux kernel
sources and their u-boot tree):
- bit 15: GEN_DIV_SOFT_RESET
- bit 14: SOFT_RESET
All information was taken from the public S805 Datasheet and Amlogic's
vendor GPL kernel sources. This patch is based on an earlier version
submitted by Carlo Caione.
Suggested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the clkids for the clocks feeding the input0 of the mmc controllers
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Expose all clocks which maybe used as DT bindings
Only clock ids internal the controller remain un-exposed
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Expose all clocks which maybe used as DT bindings
Only clock ids internal the controller remain un-exposed (none on this
particular controller at the moment)
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
gxbb clock driver gracefully handles case where the clkid is defined but
the clock hw pointer is not provided, as long as it is not at the end of
the hw_onecell_data array.
This patch ensure that the last entries are defined as well to handle
this particular case.
Fixes: a70c6e06ed ("clk: meson: gxbb: protect against holes in the onecell_data array")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
meson8b clock driver gracefully handles case where the clkid is defined
but the clock hw pointer is not provided, as long as it is not at the end
of the hw_onecell_data array.
This patch ensure that the last entries are defined as well to handle
this particular case.
Fixes: e92f7cca44 ("clk: meson8b: clean up fixed rate clocks")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
mpll0 clock is special compared to the other mplls. It needs another
bit (ssen) to be set to activate the fractional part the mpll divider
Fixes: 007e6e5c5f ("clk: meson: mpll: add rw operation")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
* Add new compatible to the meson8 clock controller for meson8b
* Add missing parents to gxbb clk81
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJZRDQVAAoJEAFRo5MEFpTRaVgQAKqGVc39PNOGuzx8P2pj4H0B
lhedpQu7XHTGc7/2/b8ezMwzgnlHnFsAJOnzpLj4FbUNbNSlJmJFaBfybbV1cgd+
MF1cN9D5ssqI5zjkXeIhhZO6ogoe3AUlhjqKJMQfK2jlbQdF9Y9GrCIFFdzj/xC8
pwI4UxRg1g0SGfsF76IaGWeBsduYr9kzZJ3Xr1zUIi32bn/peTaHL+Ye/tv8ssir
NPnIXDte8XV+gmlOk0Ir1ELqIt501UfbljKmknU4FtVmOH9B/xkuxxOZU0w0Ia1o
6uoXKDMVENQO+LFWifdexIKh5MV7fXC1wynYoiqTd0BiOA2vKryTo4lcqPblWA5T
V95wIqwjsk6+XHl5uEFT7HPm2V5QEmBKzeDA4ng6hlGB7GYxZFhpzZQK4lnNrML0
pB+crpY9/5lAdQlpC/XMkOHORhJ0862ktT45TplToprowWadnmLZBbHB7QcNe+iH
z8v26eoh800YTN5KMfiSjPXNRW6GPS8YKJmT/9vx35+ysKFMD2fW2FmM7DL5LN+M
Bv+fgbJSJ4slniqMzFCEVWfcMESGltAYKM8G2YpPUF1uf99SnRweFwf7tshPSvJ4
bhvnqUdKsWxMgag3aL2D5eKq+yCRlk6/3zobq5qlCAomr9XDMm97C4CGmFUn40iV
xiIzVBXoiydjJyaBLSzX
=0BO9
-----END PGP SIGNATURE-----
Merge tag 'meson-clk-for-4.13-2' of git://github.com/BayLibre/clk-meson into clk-next
Pull Amlogic clk driver updates from Jerome Brunet:
* Expose more clock gate on meson8 (SAR ADC, RNG, USB, SDIO, ETH)
* Add new compatible to the meson8 clock controller for meson8b
* Add missing parents to gxbb clk81
* tag 'meson-clk-for-4.13-2' of git://github.com/BayLibre/clk-meson:
clk: meson: gxbb: add all clk81 parents
clk: meson: meson8b: add compatibles for Meson8 and Meson8m2
clk: meson8b: export the ethernet gate clock
clk: meson8b: export the USB clocks
clk: meson8b: export the gate clock for the HW random number generator
clk: meson8b: export the SDIO clock
clk: meson8b: export the SAR ADC clocks
Remove the FIXME on clk81 mux and add all the documented parents
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The clock controller on Meson8, Meson8b and Meson8m2 is very similar
based on the code from the Amlogic GPL kernel sources. Add separate
compatibles for each SoC to make sure that we can easily implement
all the small differences for each SoC later on.
In general the Meson8 and Meson8m2 seem to be almost identical as they
even share the same mach-meson8 directory in Amlogic's GPL kernel
sources.
The main clocks on Meson8, Meson8b and Meson8m2 are very similar,
because they are all using the same PLL values, 90% of the clock gates
are the same (the actual diffstat of the mach-meson8/clock.c and
mach-meson8b/clock.c files is around 30 to 40 lines, when excluding
all commented out code).
The difference between the Meson8 and Meson8b clock gates seem to be:
- Meson8 has AIU_PCLK, HDMI_RX, VCLK2_ENCT, VCLK2_ENCL, UART3,
CSI_DIG_CLKIN gates which don't seem to be available on Meson8b
- the gate on Meson8 for bit 7 seems to be named "_1200XXX" instead
of "PERIPHS_TOP" (on Meson8b)
- Meson8b has a SANA gate which doesn't seem to exist on Meson8 (or
on Meson8 the same bit is used by the UART3 gate in Amlogic's GPL
kernel sources)
None of these gates is added for now, since it's unclear whether these
definitions are actually correct (the VCLK2_ENCT gate for example is
defined, but only used in some commented block).
The main difference between all three SoCs seem to be the video (VPU)
clocks. Apart from different supported clock rates (according to vpu.c
in mach-meson8 and mach-meson8b from Amlogic's GPL kernel sources) the
most notable difference is that Meson8m2 has a GP_PLL clock and a mux
(probably the same as on the Meson GX SoCs) to support glitch-free
(clock rate) switching.
None of these VPU clocks are not supported by our mainline meson8b
clock driver yet though.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Export the ethernet gate clock to the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Export the USB related clocks (for the USB controller and the USB2 PHYs)
so they can be used in the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This exports the clock so it can be used in the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Export the SDIO clock so it can be used in the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Export the clocks for the SAR ADC so they can be used in the
dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
These can be marked as const * const.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* Expose more i2s and spdif output clocks
* Expose EE uart and SPICC gate clocks
* Remove cpu_clk from to gxbb
* Mark clk81 as critical on gxbb
* Add CEC EE clocks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=8rsv
-----END PGP SIGNATURE-----
Merge tag 'meson-clk-for-4.13' of git://github.com/BayLibre/clk-meson into clk-next
Pull Amlogic clock driver updates from Jerome Brunet:
* Expose more i2s and spdif output clocks
* Expose EE uart and SPICC gate clocks
* Remove cpu_clk from to gxbb
* Mark clk81 as critical on gxbb
* Add CEC EE clocks
* tag 'meson-clk-for-4.13' of git://github.com/BayLibre/clk-meson:
clk: meson-gxbb: Add EE 32K Clock for CEC
clk: gxbb: remove CLK_IGNORE_UNUSED from clk81
clk: meson: meson8b: mark clk81 as critical
clk: meson: gxbb: remove the "cpu_clk" from the GXBB and GXL driver
clk: meson-gxbb: un-export the CPU clock
clk: meson-gxbb: expose UART clocks
clk: meson-gxbb: expose SPICC gate
clk: meson-gxbb: expose spdif master clock
clk: meson-gxbb: expose i2s master clock
clk: meson-gxbb: expose spdif clock gates
On Amlogic GX SoCs, there is two CEC controllers :
- An Amlogic CEC custom in the AO domain
- The Synopsys HDMI-TX Controller in the EE domain
Each of these controllers needs a 32.768KHz clock, but there is two paths :
- In the EE domain, the "32k_clk" this patchs is adding
- In the AO domain, with a more complex dual divider more precise setup
The AO 32K clock support will be pushed later in the corresponding
gxbb-aoclk driver when the AE CEC driver is ready.
The EE 32k_clk must be pushed earlier since mainline support for CEC in the
Synopsys HDMI-TX controller is nearby.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[Rebased patch on top of last changes]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
clk81 already has CLK_IS_CRITICAL so CLK_IGNORE_UNUSED is not
necessary
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Disabling clk81 results in an immediate freeze of the whole system. This
can happen "accidentally" when the last child-clock of clk81 is disabled
(in this case the common clock framework also disables clk81, even if it
was only enabled indirectly before).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
It seems that the "cpu_clk" was carried over from the meson8b clock
controller driver. On Meson GX (GXBB/GXL/GXM) the registers which are
used by the cpu_clk have a different purpose (in other words: they don't
control the CPU clock anymore). HHI_SYS_CPU_CLK_CNTL1 bits 31:24 are
reserved according to the public S905 datasheet, while bit 23 is the
"A53_trace_clk_DIS" gate (which according to the datasheet should only
be used in case a silicon bug is discovered) and bits 22:20 are a
divider (A53_trace_clk). The meson clk-cpu code however expects that
bits 28:20 are reserved for a divider (according to the public S805
datasheet this "SCALE_DIV: This value represents an N+1 divider of the
input clock.").
The CPU clock on Meson GX SoCs is provided by the SCPI DVFS clock
driver instead. Two examples from a Meson GXL S905X SoC:
- vcpu (SCPI DVFS clock 0) rate: 1000000000 / cpu_clk rate: 708000000
- vcpu (SCPI DVFS clock 0) rate: 1512000000 / cpu_clk rate: 708000000
Unfortunately the CLKID_CPUCLK was already exported (but is currently
not used) to DT. Due to the removal of this clock definition there is
now a hole in the clk_hw_onecell_data (which is not a problem because
this case is already handled in gxbb_clkc_probe).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The CPU clock defined in the Meson GX clock driver is actually a
left-over from the Meson8b clock controller. Un-export the clock so we
can remove it from the driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Expose the clock ids of the three none AO uarts to the dt-bindings
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[tidy the commit message to match similar change]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Expose the SPICC gate clock to enable the SPICC controller.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[tidy commit message to match similar changes]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Expose the spdif master clock and the mux to select the appropriate spdif
clock parent depending on the data source.
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Expose the clock gates required for the spdif output
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
With CONFIG_RESET_CONTROLLER=n we see the following link error in the
meson gxbb clk driver:
drivers/built-in.o: In function 'gxbb_aoclkc_probe':
drivers/clk/meson/gxbb-aoclk.c:161: undefined reference to 'devm_reset_controller_register'
Fix this by selecting the reset controller subsystem.
Fixes: f8c11f7991 ("clk: meson: Add GXBB AO Clock and Reset controller driver")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: Added fixes-by tag]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
to me not catching up as quickly on patch review than anything else.
Overall it seems normal though, a few small changes to the core, mostly
small non-critical fixes here and there as well as driver updates for new
and existing hardware support. The biggest things are the TI clk driver
rework to lay the groundwork for clkctrl support in the next merge window
and the AmLogic audio/graphics clk support.
Core:
* clk_possible_parents debugfs file so we know which parents a clk
could possibly have
* Fix to make clk rate change notifiers stop on the first failure instead
of continuing
New Drivers:
* Mediatek MT6797 SoCs
* hi655x PMIC clks
* AmLogic Meson SoC i2s and spdif audio clks and Mali graphics clks
* Allwinner H5 SoCs and PRCM hardware
Updates:
* Nvidia Tegra T210 cleanups and non-critical fixes
* TI OMAP cleanups in preparation for clkctrl support
* Trivial fixes like kcalloc(), devm_* conversions, and seq_puts()
* ZTE zx296718 SoC VGA clks
* Rockchip clk-ids, fixups, and rename of rk1108 to rv1108
* Support for IDT VersaClock 5P49V5935
* Renesas R-Car H3 and M3-W IMR clks and ES2.0 rev of R-Car H3 support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJZE0YJAAoJEK0CiJfG5JUl9tEQAKVJx8VztYGt1REoFMtEEHmO
azhxT/uYGgdOMAr9a3mQxqfm5cJbjnb1EZj2RfC1XHs31BF66j40y9+5d8hY8Hzu
5IkY86s77TlqxGLwQcAsU75Q9cFrEW9X0KJ6OSzlrcc5hKlAEk/Z5lBKoQAm3mlU
JqD4DSyFqP0X3YSxV5R7yfarb/X3ekCiQ13EDrPRRhyvHUi6ReUJDDgbPHtA+O2c
ftLAARmxjzitzyvdXokXudkfNm8F5KePK+QkVikf6D/q+kx1D0BNJwZIjhpoiksn
z6LImLQ8l91AWghmqqpOFXolxQncPU+bJIL9Pox76p5b3EzbQuthIafiso8KsDST
4g3mHm42Yfx9uoF+U+pR8IeZfj5yQT91bvf8naPz/ngWMAlLP1IKJUvJN6jeTiwe
cO6GIec1OH40Xl7v/9EafMwDcnFG0cwQmzr/M6wi1dUlmbSygP9NOMTHlr6W/0wa
K2hCD6b5UHEgHmdfiJbZ2tKxLO0e8LABW+AU8fQH5S2eNe14vY0GvCzfAq5MArIz
QRpso/kdtGpTpwMEvV6PUmJ0IxYEjtNJVjGJYbORwios0SK0Xl6bJWf7gwn5crB6
nua9tVZtJEOHJS7S+ESp3VvuXj2/UGPoRRf5OsERo1S6ydGUQH+wDi1SJMdo/vtX
bIPzIw6WPxMp24JyKOhh
=/5a/
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Sort of on the quieter side this time, which is probably due more to
me not catching up as quickly on patch review than anything else.
Overall it seems normal though, a few small changes to the core,
mostly small non-critical fixes here and there as well as driver
updates for new and existing hardware support.
The biggest things are the TI clk driver rework to lay the groundwork
for clkctrl support in the next merge window and the AmLogic
audio/graphics clk support.
Core:
- clk_possible_parents debugfs file so we know which parents a clk
could possibly have
- Fix to make clk rate change notifiers stop on the first failure
instead of continuing
New Drivers:
- Mediatek MT6797 SoCs
- hi655x PMIC clks
- AmLogic Meson SoC i2s and spdif audio clks and Mali graphics clks
- Allwinner H5 SoCs and PRCM hardware
Updates:
- Nvidia Tegra T210 cleanups and non-critical fixes
- TI OMAP cleanups in preparation for clkctrl support
- trivial fixes like kcalloc(), devm_* conversions, and seq_puts()
- ZTE zx296718 SoC VGA clks
- Rockchip clk-ids, fixups, and rename of rk1108 to rv1108
- IDT VersaClock 5P49V5935 support
- Renesas R-Car H3 and M3-W IMR clks and ES2.0 rev of R-Car H3
support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (151 commits)
clk: x86: pmc-atom: Checking for IS_ERR() instead of NULL
clk: ti: divider: try to fix ti_clk_register_divider
clk: mvebu: Use kcalloc() in two functions
clk: mvebu: Use kcalloc() in of_cpu_clk_setup()
clk: nomadik: Delete error messages for a failed memory allocation in two functions
clk: nomadik: Use seq_puts() in nomadik_src_clk_show()
clk: Improve a size determination in two functions
clk: Replace four seq_printf() calls by seq_putc()
clk: si5351: Delete an error message for a failed memory allocation in si5351_i2c_probe()
clk: si5351: Use devm_kcalloc() in si5351_i2c_probe()
clk: at91: Use kcalloc() in of_at91_clk_pll_get_characteristics()
reset: mediatek: Add MT2701 ethsys reset controller include file
clk: mediatek: add mt2701 ethernet reset
clk: hi6220: Add the hi655x's pmic clock
clk: ti: fix building without legacy omap3
clk: ti: fix linker error with !SOC_OMAP4
clk: hi3620: Fix a typo in one variable name
clk: hi3620: Delete error messages for a failed memory allocation in two functions
clk: hi3620: Use kcalloc() in hi3620_mmc_clk_init()
clk: hisilicon: Delete error messages for failed memory allocations in hisi_clk_init()
...
Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch of smaller
changes, but also some new platforms that are worth mentioning:
* Rockchip RK3399 platforms for Chromebooks, including Samsung Chromebook
Plus (Kevin)
* Orange Pi PC2 (Allwinner H5)
* Freescale LS2088A and LS1088A SoCs
* Expanded support for Nvidia Tegra186 (and Jetson TX2)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=q3Ix
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Olof Johansson:
"Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch
of smaller changes, but also some new platforms that are worth
mentioning:
- Rockchip RK3399 platforms for Chromebooks, including Samsung
Chromebook Plus (Kevin)
- Orange Pi PC2 (Allwinner H5)
- Freescale LS2088A and LS1088A SoCs
- Expanded support for Nvidia Tegra186 (and Jetson TX2)"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (180 commits)
arm64: dts: Add basic DT to support Spreadtrum's SP9860G
arm64: dts: exynos: Use - instead of @ for DT OPP entries
arm64: dts: exynos: Add support for s6e3hf2 panel device on TM2e board
arm64: dts: juno: add information about L1 and L2 caches
arm64: dts: juno: fix few unit address format warnings
arm64: marvell: dts: enable the crypto engine on the Armada 8040 DB
arm64: marvell: dts: enable the crypto engine on the Armada 7040 DB
arm64: marvell: dts: add crypto engine description for 7k/8k
arm64: dts: marvell: add sdhci support for Armada 7K/8K
arm64: dts: marvell: add eMMC support for Armada 37xx
arm64: dts: hisi: add pinctrl dtsi file for HiKey960 development board
arm64: dts: hisi: add drive strength levels of the pins for Hi3660 SoC
arm64: dts: hisi: enable the NIC and SAS for the hip07-d05 board
arm64: dts: hisi: add SAS nodes for the hip07 SoC
arm64: dts: hisi: add RoCE nodes for the hip07 SoC
arm64: dts: hisi: add network related nodes for the hip07 SoC
arm64: dts: hisi: add mbigen nodes for the hip07 SoC
arm64: dts: rockchip: fix the memory size of PX5 Evaluation board
arm64: dts: hisilicon: add dts files for hi3798cv200-poplar board
dt-bindings: arm: hisilicon: add bindings for hi3798cv200 SoC and Poplar board
...
On Meson8b the MPLL parent clock (fixed_pll) has a rate of 2550MHz.
Multiplying this with SDM_DEN results in a value greater than 32bits.
This is not a problem on the 64bit Meson GX SoCs, but it may result in
undefined behavior on the older 32bit Meson8b SoC.
While rate_from_params was only introduced recently to make the math
reusable from _round_rate and _recalc_rate the original bug exists much
longer.
Fixes: 1c50da4f27 ("clk: meson: add mpll support")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[as discussed on the ml, use DIV_ROUND_UP_ULL]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
According to the public datasheet all register bits in HHI_MPLL_CNTL7,
HHI_MPLL_CNTL8 and HHI_MPLL_CNTL9 default to zero. On all GX SoCs these
seem to be initialized by the bootloader to some default value.
However, on my Meson8 board they are not initialized, leading to a
division by zero in rate_from_params as the math is:
(parent_rate * SDM_DEN) / ((SDM_DEN * 0) + 0)
According to the datasheet, the minimum n2 value is 4. The rate provided
by the clock when n2 is less than this minimum is unpredictable. In such
case, we report an error.
Although the rate_from_params function was only introduced recently the
original bug has been there for much longer. It was only exposed
recently when the MPLL clocks were added to the Meson8b clock driver.
Fixes: 1c50da4f27 ("clk: meson: add mpll support")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This adds the cts_i958 clock to control the clock source of the spdif
output block. This mux is not explicitly mentionned in the documentation
but it is critical to the spdif dai. It is used to select whether the clock
source of the spdif output is cts_amclk (when data are taken from i2s
buffer) or the cts_mclk_i958 (when data are taken from the spdif buffer)
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add the spdif master clock also referred as cts_mclk_i958
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add the i2s master clock also referred as cts_amclk
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The audio divider needs a specific clock divider driver.
With am mpll parent clock, which is able to provide a fairly precise rate,
the generic divider tends to select low value of the divider. In such case
the quality of the clock is very poor. For the same final rate, maximizing
the audio clock divider value and selecting the corresponding mpll rate
gives better results. This is what this driver aims to acheive. So far, so
good.
Cc: Hendrik v. Raven <hendrik@consetetur.de>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The clock controller is getting more complex and it might be possible, in
the future, to have holes in the clk_hw_onecell_data array. Just make sure
we skip those holes if it ever happens.
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The clock tree in the Amlogic GXBB and GXL/GXM SoCs is shared, but the GXL/GXM
SoCs embeds a different GP0 PLL, and needs different parameters with a vendor
provided reduced rate table.
This patch adds the GXL GP0 variant, and adds a GXL DT compatible in order
to use the GXL GP0 PLL instead of the GXBB specific one.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490178747-14837-4-git-send-email-narmstrong@baylibre.com
Tha Amlogic GXBB SoC GP0 PLL needs some vendor provided parameters to be
initializated in the the GP0 control registers before configuring the rate
with the rate table provided parameters.
GXBB GP0 PLL tweaks are also selected to respect the vendor init procedure.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490178747-14837-3-git-send-email-narmstrong@baylibre.com
In recent Amlogic GXBB, GXL and GXM SoCs, the GP0 PLL needs some specific
parameters in order to initialize and lock correctly.
This patch adds an optional PARAM table used to initialize the PLL to a
default value with it's parameters in order to achieve to desired frequency.
The GP0 PLL in GXBB, GXL/GXM also needs some tweaks in the initialization
steps, and these are exposed along the PARAM table.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490178747-14837-2-git-send-email-narmstrong@baylibre.com
The Mali is clocked by two identical clock paths behind a glitch free mux
to safely change frequency while running.
The two "mali_0" and "mali_1" clocks are composed of a mux, divider and gate.
Expose these two clocks trees using generic clocks.
Finally the glitch free mux is added as "mali" clock.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490177935-9646-3-git-send-email-narmstrong@baylibre.com
Gxbb datasheet says N2 maximum value is 127 but the register field is
9 bits wide, the maximum value should 511.
Test shows value greater than 127, all the way to 511, works well
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-9-jbrunet@baylibre.com
Use read/write operations for the mpll clocks instead of the
read-only ones.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-7-jbrunet@baylibre.com
This patch adds new callbacks to the meson-mpll driver to control
and set the pll rate. For this, we also need to add the enable bit and
sdm enable bit. The corresponding parameters are added to mpll data
structure.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-6-jbrunet@baylibre.com
Until now, there was only 2 dividers and 2 muxes declared for the gxbb
platform. With the ongoing work on various subsystem, including audio,
this is about to change. Use the same approach as gates for dividers and
muxes, putting them in tables to fix the register address at runtime.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-5-jbrunet@baylibre.com
Until now, there was only 1 divider and 1 mux declared for the meson8b
platform. With the ongoing work on various system, including audio, this
is about to change. Use the same approach as gates for dividers and muxes,
putting them in tables to fix the register address at runtime.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-4-jbrunet@baylibre.com
parameter val is not enclosed in parenthesis which is buggy when given an
expression instead of a simple value
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-2-jbrunet@baylibre.com
Expose clock CLKID_RNG0 which is needed for the HW random number generator.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These updates have been kept in a separate branch mostly because
they rely on updates to the respective clk drivers to keep the
shared header files in sync.
This includes two branches for arm64 dt updates, both following up
on earlier changes for the same platforms that are already merged:
Samsung:
- add USB3 support in Exynos7
- minor PM related updates
Amlogic:
- new machines: WeTek Set-top-boxes
- various devices added to DT
There are also a couple of bugfixes that trickled in since the
start of the merge window:
- The moxart_defconfig was not building the intended platform
- CPU-hotplug was broken on ux500
- Coresight was broken on Juno (never worked)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=A3U6
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
This includes two branches for arm64 dt updates, both following up on
earlier changes for the same platforms that are already merged:
Samsung:
- add USB3 support in Exynos7
- minor PM related updates
Amlogic:
- new machines: WeTek Set-top-boxes
- various devices added to DT
There are also a couple of bugfixes that trickled in since the start
of the merge window:
- The moxart_defconfig was not building the intended platform
- CPU-hotplug was broken on ux500
- Coresight was broken on Juno (never worked)"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
ARM: deconfig: fix the moxart defconfig
ARM: ux500: resume the second core properly
arm64: dts: juno: update definition for programmable replicator
arm64: dts: exynos: Add regulators for Vbus and Vbus-Boost
arm64: dts: exynos: Add USB 3.0 controller node for Exynos7
arm64: dts: exynos: Use macros for pinctrl configuration on Exynos7
pinctrl: dt-bindings: samsung: Add Exynos7 specific pinctrl macro definitions
arm64: dts: exynos: Add initial configuration for DISP clocks for TM2/TM2e
ARM64: dts: meson-gxbb-p200: add ADC laddered keys
ARM64: dts: meson: meson-gx: add the SAR ADC
ARM64: dts: meson-gxl: add the pwm_ao_b pin
ARM64: dts: meson-gx: add the missing pwm_AO_ab node
clk: gxbb: fix CLKID_ETH defined twice
ARM64: dts: meson-gxl: rename Nexbox A95x for consistency
clk: gxbb: add the SAR ADC clocks and expose them
dt-bindings: amlogic: Add WeTek boards
ARM64: dts: meson-gxbb: Add support for WeTek Hub and Play
dt-bindings: vendor-prefix: Add wetek vendor prefix
ARM64: dts: meson-gxm: Rename q200 and q201 DT files for consistency
ARM64: dts: meson-gx: Add HDMI HPD/DDC pinctrl nodes
...
CLKID_ETH is define in the dt-bindings but has not be commented out in the
clock driver. Just do it now.
Fixes: 738f66d321 ("clk: gxbb: add AmLogic GXBB clk controller driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
During meson8b clock probe, clk81 register address is fixed twice.
First using the meson8b_clk_gates array, then by directly changing
meson8b_clk81 register.
As a result meson8b_clk81.reg = HHI_MPEG_CLK_CNTL + clk_base + clk_base.
Fixed by just removing the second fixup.
Fixes: e31a1900c1 ("meson: clk: Add support for clock gates")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The HHI_SAR_CLK_CNTL contains three SAR ADC specific clocks:
- a mux clock to choose between different ADC reference clocks (this is
2-bit wide, but the datasheet only lists the parents for the first
bit)
- a divider for the input/reference clock
- a gate which enables the ADC clock
Additionally this exposes the ADC core clock (CLKID_SAR_ADC) and
CLKID_SANA (which seems to enable the analog inputs, but unfortunately
there is no documentation for this - we just mimic what the vendor
driver does).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Export HDMI clock from internal to dt-bindings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
These updates have been kept in a separate branch mostly because
they rely on updates to the respective clk drivers to keep the
shared header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been
merged for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and
usb driver changes are required and included here, and also
the clk tree changes.
- The Allwinner platforms have seen a large-scale change to their
clk drivers and the dts file updates must come after that.
This includes the newly added Nextthing GR8 platform, which is
derived from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't
added until just before the merge window
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OmAu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been merged
for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and usb
driver changes are required and included here, and also the clk
tree changes.
- The Allwinner platforms have seen a large-scale change to their clk
drivers and the dts file updates must come after that. This
includes the newly added Nextthing GR8 platform, which is derived
from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't added
until just before the merge window"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
ARM: dts: lpc32xx: add device node for IRAM on-chip memory
ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
ARM: dts: sun8i: add pinmux for UART1 at PG
dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
dts: sun8i-h3: add pinmux definitions for I2C0-2
dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
dts: sun8i-h3: add pinmux definitions for UART2-3
ARM: dts: sun9i: a80-optimus: Disable EHCI1
ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
...
I2C and AO_I2C clocks are needed for the i2c driver, expose to DT
(and comment out in clk driver)
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
USB0_DDR_BRIDGE and USB1_DDR_BRIDGE1 are needed for the related
dwc2 usb controller. USB, USB0 and USB1 are needed for the PHYs.
Expose these clocks to DT and comment out in clk driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
SPI clock is needed for the spifc driver, expose to DT
(and comment out in the clk driver)
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This exposes the MPLL2 clock as this is one of the input clocks of the
ethernet controller's internal mux.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The addition of many gate clocks added two entries in an array for
the same value:
drivers/clk/meson/meson8b.c:479:10: error: initialized field overwritten [-Werror=override-init]
[CLKID_GCLK_VENCI_INT] = &meson8b_gclk_venci_int.hw,
[CLKID_GCLK_VENCI_INT] = &meson8b_gclk_vencp_int.hw,
This was clearly an accident, and since all other identifiers are
listed in the order in which they are defined, I'm changing the
first one to CLKID_GCLK_VENCI_INT0, making it all consistent again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: e31a1900c1 ("meson: clk: Add support for clock gates")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Use the builtin_platform_driver() macro to make the code simpler.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds support for the meson8b clock gates. Most of
them are disabled by Amlogic U-Boot, but need to be enabled
for ethernet, USB and many other components.
Signed-off-by: Alexander Müller <serveralex@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1472319654-59048-7-git-send-email-serveralex@gmail.com
The macro used gxbb_ prefix for clock definitions. In order
to share the macro between gxbb and meson8b, the prefix must
be moved to gxbb.c.
Signed-off-by: Alexander Müller <serveralex@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1472319654-59048-6-git-send-email-serveralex@gmail.com
Only expose future CLKID constants if necessary. This patch
removes CLK_NR_CLKS from the DT bindings but leaves all previously
defined CLKIDs there to keep backward compatibility.
Signed-off-by: Alexander Müller <serveralex@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1472319654-59048-5-git-send-email-serveralex@gmail.com
sizeof() when applied to a pointer typed expression gives the
size of the pointer, not that of the pointed data.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Fixes: f8c11f7991 ("clk: meson: Add GXBB AO Clock and Reset controller driver")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Adds a Clock and Reset controller driver for the Always-On part
of the Amlogic Meson GXBB SoC.
It exports paired Clocks and Resets lines that will be used by
peripherals in the Always-On subsystem.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the SD/eMMC gate clocks and expose them for use by DT.
While at it, also explose FCLK_DIV2 since this is one of the input
clocks to the mux internal to each of the SD/eMMC blocks.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Use the builtin_platform_driver() macro to make the code simpler.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This reverts commit e16fb2e635.
Updated documentation from the chip vendor reveals that this clock is
not required for correct operation of the MMC controller. As such, do
not expose it to DT.
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The MMC_PCLK is needed for the SD/eMMC driver, expose to DT (and comment
out in clk driver)
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20160707033837.20029-1-khilman@baylibre.com
The Kconfig currently controlling compilation of this code is:
drivers/clk/meson/Kconfig:config COMMON_CLK_GXBB
drivers/clk/meson/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE and ALIAS are no-op for non-modules.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-amlogic@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20160704211220.5685-3-paul.gortmaker@windriver.com
The Kconfig currently controlling compilation of this code is:
drivers/clk/meson/Kconfig:config COMMON_CLK_MESON8B
drivers/clk/meson/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
However a recent commit added a bunch of modular boilerplate to this
driver.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
Also note that MODULE DEVICE_TABLE/ALIAS are no-op when non-modular.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-amlogic@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20160704211220.5685-2-paul.gortmaker@windriver.com
The gxbb clock controller is the primary clock generation unit for the
AmLogic GXBB SoC. It is clocked by a fixed 24MHz xtal, contains several
PLLs and the usual post-dividers, muxes, dividers and leaf gates that
are fed into various IP blocks in the SoC.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Fractional MPLLs are a superset of the existing AmLogic MPLLs. They add
in a couple of new bitfields for further dividing the clock rate to
achieve rates with fractional hertz.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
MPLLs are adjustable rate clocks derived from PLLs. On both Meson8b and
GXBB they appear to be only derived from fixed_pll.
Add support for these clock types so that they can be added to their
respective drivers.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
There are a series of peripheral and system gate clocks that fan out
from the clk81 signal. Add a helper macro to statically initialize these
gate clocks.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Break the AmLogic clock code up so that only the necessary parts are
compiled and linked. The core code is selected by both arm and arm64
builds with COMMON_CLK_AMLOGIC. The individual drivers have their own
config options as well.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This patch creates a proper platform_driver for the meson8b clock
controller. Use of CLK_OF_DECLARE is removed, and can be added back in
later if very early registration of some clocks is required.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Remove the composite clock registration function and helpers. Replace
unnecessary configuration struct with static initialization of the
desired clock type.
To preserve git bisect this patch also flips the switch and starts using
of_clk_add_hw_provider instead of the deprecated meson_clk_register_clks
method. As a byproduct clk.c can be deleted.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This clock is undocumented and always orphaned. Get rid of it until we
have more complete clock tree documentation.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Remove the cpu clock registration function and helpers. Replace
unnecessary configuration struct with static initialization of the
desired clock type.
Ninja rename a5_clk to cpu_clk to better align with cpufreq convention.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Remove the fixed factor registration function and helpers. Replace
unnecessary configuration struct with static initialization of the
desired clock type.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Remove the pll registration function and helpers. Replace unnecessary
configuration struct with static initialization of the desired clock
type.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Remove the fixed_rate registration function and helpers from clkc.[ch].
Replace unnecessary configuration struct with static initialization of
the desired clock type.
While we're here, begin the transition to a proper platform_driver and
call of_clk_add_hw_provider with a shiny new struct clk_hw_onecell_data.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The register offsets in the data sheet are confusing. Document them more
thoroughly.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
As preparation for arm64 based mesongxbb, which pulls in this code once
enabling ARCH_MESON, fix a size_t vs. unsigned int type mismatch.
The loop uses a local unsigned int variable, so adopt that type,
matching the header.
Fixes: 7a29a86943 ("clk: meson: Add support for Meson clock controller")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Clock provider drivers generally shouldn't include clk.h because
it's the consumer API. Only include clk.h if it's actually used.
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This error handling hopefully isn't needed but it make the static
checkers happy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds support for the basic clocks found on the Amlogic
Meson8b SoCs.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patchset adds the infrastructure for registering and managing the
core clocks found on Amlogic MesonX SoCs. In particular:
- PLLs
- CPU clock
- Fixed rate clocks, fixed factor clocks, ...
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
