Let's not rely on the dummy_controller embedded in nand_chip.legacy
and explicitly inherit from nand_controller instead.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200513172248.141402-1-boris.brezillon@collabora.com
The current code checks that the whole OOB area is erased.
This is a problem when JFFS2 cleanmarkers are added to the OOB, since it will
fail due to the usable OOB bytes not being 0xff.
Correct this by only checking that data and ECC bytes aren't 0xff.
Fixes: 02b88eea9f ("mtd: brcmnand: Add check for erased page bitflips")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200512082451.771212-1-noltari@gmail.com
Some controller using the instruction parse infrastructure might need
to know which CS a specific sub-operation is targeting. Let's propagate
this information.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200505101353.1776394-2-boris.brezillon@collabora.com
This patch renames functions and local variables.
This cleanup is done to get all functions starting by stm32_fmc2_nfc
in the FMC2 raw NAND driver when all functions will start by
stm32_fmc2_ebi in the FMC2 EBI driver.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1589284068-4079-2-git-send-email-christophe.kerello@st.com
This patch removes the constant FMC2_TIMEOUT_US.
FMC2_TIMEOUT_MS will be used each time that we need to wait (except
when the timeout value is set by the framework).
It was seen, during stress tests with the sequencer in an overloaded
system, that we could be close to 1 second, even if we never met this
value. To be safe, FMC2_TIMEOUT_MS is set to 5 seconds.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1588756279-17289-4-git-send-email-christophe.kerello@st.com
Implement exec_op() so we can later get rid of the legacy
implementation.
It's worth noting that the new implementation assert/deassert the CE
pin on each operation, which might not be necessary. We also dropped
the extra reset done at chip selection time on DOC2001plus. If it's
needed we really should do something smarter, because having a reset
everytime we access the chip is not that great perf-wise.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200501143917.1388957-5-boris.brezillon@collabora.com
Single byte accesses normally go through read_byte() but we are about
to use this function in the exec_op() implementation and thus needs to
prepare for single byte reads.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200501143917.1388957-2-boris.brezillon@collabora.com
We have a dummy block_bad() implementation returning 0. Let's set the
NAND_NO_BBM_QUIRK flag and let the core take care of that.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200511064917.6255-3-boris.brezillon@collabora.com
We have a dummy block_bad() implementation returning 0. Let's set the
NAND_NO_BBM_QUIRK flag and let the core take care of that.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200511064917.6255-2-boris.brezillon@collabora.com
Some controllers with embedded ECC engines override the BBM marker with
data or ECC bytes, thus making bad block detection through bad block
marker impossible. Let's flag those chips so the core knows it shouldn't
check the BBM and consider all blocks good.
This should allow us to get rid of two implementers of the
legacy.block_bad() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200511064917.6255-1-boris.brezillon@collabora.com
Some controller drivers do not support executing regular
nand_read/write_page_raw() helpers. For that, we created
nand_monolithic_read/write_page_raw() alternatives. Let's now allow
the driver to overload the ECC ->read/write_page_raw() hooks when
these hooks are supported.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-14-miquel.raynal@bootlin.com
Some controller drivers do not support executing regular
nand_read/write_page_raw() helpers. For that, we created
nand_monolithic_read/write_page_raw() alternatives. Let's now allow
the driver to overload the ECC ->read/write_page_raw() hooks.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-13-miquel.raynal@bootlin.com
The current nand_read/write_page_raw() helpers are already widely used
but do not fit the purpose of "constrained" controllers which cannot,
for instance, separate command/address cycles with data cycles.
Workaround this issue by proposing alternative helpers that can be
used by these controller drivers instead.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-12-miquel.raynal@bootlin.com
We already know that there are controllers not able to read the three
copies of the parameter page in one go. The workaround was to first
request the controller to assert command and address cycles on the
NAND bus to trigger a parameter page read, and then do a read
operation for each page.
But there are also controllers which are not able to split the
parameter page read between the command/address cycles and the actual
data operation.
Let's use a regular PARAMETER PAGE READ operation for the first
iteration and use eithe a CHANGE READ COLUMN or a simple DATA READ
operation for the following copies, depending on what the controller
supports. The default for non-exec-op compliant drivers remains
unchanged: use a SIMPLE READ.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-11-miquel.raynal@bootlin.com
We already know that there are controllers not able to read the three
copies of the parameter page in one go. The workaround was to first
request the controller to assert command and address cycles on the
NAND bus to trigger a parameter page read, and then do a simple read
operation for each page.
But there are also controllers which are not able to split the
parameter page read between the command/address cycles and the actual
data operation.
Let's use a regular PARAMETER PAGE READ operation for the first
iteration and use either a CHANGE READ COLUMN or a simple DATA READ
operation for the following copies, depending on what the controller
supports. The default behavior for non-exec-op compliant drivers
remains the same: DATA READ.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-10-miquel.raynal@bootlin.com
This can be used to discriminate between two path in the parameter
page detection: use data_in cycles (like before) if supported, use the
CHANGE READ COLUMN command otherwise.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-9-miquel.raynal@bootlin.com
Let's use a helper to clearly check if an operation is supported or not.
Return -ENOTSUPP when ->exec_op() is not implemented as we cannot know.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-8-miquel.raynal@bootlin.com
The logic in nand_do_read_ops() is to use a bufpoi variable, either
set to the original buffer, or set to a bounce buffer which in the end
happens to be chip->data_buf depending on the value of the
use_bounce_buf boolean. This is not a reason to call chip->data_buf
directly when we know that we are using the bounce buffer. Let's use
bufpoi instead to be consistent.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-7-miquel.raynal@bootlin.com
Both in nand_do_read_ops() and nand_do_write_ops() there is a boolean
called use_bufpoi which is set to true in case of unaligned request or
when there is a need for a DMA-able buffer. It basically means "use a
bounce buffer".
Depending on the value of use_bufpoi, the bufpoi variable is always
used and will either point to the original buffer or to the nand_chip
structure "internal data buffer" (this buffer is allocated with
kmalloc() on purpose so that it will be DMA-compliant).
In all cases bufpoi is used so the boolean name is misleading. Rename
use_bufpoi to be use_bouce_buf to be more accurate.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-6-miquel.raynal@bootlin.com
NAND controller drivers can set the NAND_USE_BOUNCE_BUFFER flag to a
chip 'option' field. With this flag, the core is responsible of
providing DMA-able buffers.
The current behavior is to not force the use of a bounce buffer when
the core thinks this is not needed. So in the end the name is a bit
misleading, because in theory we will always have a DMA buffer but in
practice it will not always be a bounce buffer.
Rename this flag NAND_USES_DMA to be more accurate.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-4-miquel.raynal@bootlin.com
These flags are in a strange order, reorder the list, add spaces when
it is relevant, pack definitions that are related.
There is no functional change.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200507105241.14299-3-miquel.raynal@bootlin.com
The MTD layer provides an SLC mode (purely software emulation of SLC
behavior) addressing the paired-pages corruption issue, which was the
main reason for refusing attaching MLC NANDs to UBI.
Relax this rule and allow partitions that have the
MTD_EMULATE_SLC_ON_MLC flag set to be attached.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/linux-mtd/20200503155341.16712-9-miquel.raynal@bootlin.com
Add a boolean property to force a specific partition attached to an MLC
NAND to be accessed in an emulated SLC mode this making this partition
immune to paired-pages corruptions.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200503155341.16712-6-miquel.raynal@bootlin.com
MLC NANDs can be made a bit more reliable if we only program the lower
page of each pair. At least, this solves the paired-pages corruption
issue.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200503155341.16712-5-miquel.raynal@bootlin.com
Now that exec_op() is implemented we no longer need to implement the
legacy hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200501090650.1138200-5-boris.brezillon@collabora.com
Now that we have our own controller struct we can keep the MMIO pointer
in there and use instead of using the chip->legacy.IO_ADDR_{R,W} fields.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200501090650.1138200-3-boris.brezillon@collabora.com
The CS553x companion chip embeds 4 NAND controllers. Declare them as
NAND controllers instead of NAND chips. That's done in preparation
of the transition to exec_op().
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200501090650.1138200-2-boris.brezillon@collabora.com
Before reworking a little bit the JEDEC detection code, let's
clean the coding style of an if statement to improve readability.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-10-miquel.raynal@bootlin.com
During detection the logic on the NAND bus is:
/* Regular ONFI detection */
1/ read the three NAND parameter pages
/* Extended parameter page detection */
2/ send "read the NAND parameter page" commands without reading
actual data
3/ move the column pointer to the extended page and read it
If fact, as long as there is nothing happening on the NAND bus between
1/ and 3/, the operation 2/ is redundant so remove it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200428094302.14624-8-miquel.raynal@bootlin.com
