This patch adds mout_aclk266_gscl_sub mux clock and adjusts definitions
of GSCL domain gate clocks to use it as their parent, as specified in
SoC documentation.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
This patch renames all mux clocks to start with mout_ prefix and all div
clocks to start with div_ prefix for consistency with other clocks
already defined this way.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
This patch reorders clock definitions, so they are sorted by register
addresses and bitfield shifts. When at it, blank lines are added to
separate definitions of clocks from different registers.
Overall this should make the driver more readable and reduce the number
of potential conflicts when adding new entries.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
Move reg_save[] into CONFIG_PM_SLEEP dependency block as it is used only
by suspend and resume functions.
This fixes the warning on CONFIG_PM_SLEEP=n:
drivers/clk/samsung/clk-exynos-audss.c:29:22: warning: ‘reg_save’ defined but not used [-Wunused-variable]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The sysreg (system register) generates control signals for various blocks
like disp1blk, i2c, mipi, usb etc. However, it gets disabled as an unused
clock at boot-up. This can lead to failures in operation of above blocks,
because they can not be configured properly if this clock is disabled.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Updated patch description.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Due to incorrect clock specified in MDMA0 node, using MDMA0 controller
could cause system failures, due to wrong clock being controlled. This
patch fixes this by specifying correct clock.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Corrected commit message and description.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Adds gate clock for MDMA0 on Exynos5250 SoC. This is needed to ensure
that the clock is enabled when MDMA0 is used on systems on which
firmware gates the clockby default.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Updated patch description.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The CLK_GATE_IP_ACP register offset is incorrectly listed making
definition of g2d clock incorrect, which may lead to system failures
when trying to use G2D on systems on which firmware gates this clock
by default. Fix this and the register ordering as well.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Updated patch description.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The gate clocks for the MFC sysmmus appear to be flipped, i.e.
GATE_IP_MFC[2] gates sysmmu_mfcl and GATE_IP_MFC[1] gates sysmmu_mfcr.
Fix this so that the MFC will start up.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The SRC_MFC register offset was incorrect, which could cause have caused
wrong calculation of rate of sclk_mfc clock, that could in turn lead to
incorrect operation of MFC. This patch corrects it.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Updated patch description]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Populate ${DEBUGS_MOUNT_POINT}/clk if CONFIG_DEBUG_FS is set. This
eliminates the extra (annoying) step of enabling the config option
manually.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
'break' after 'goto' is redundant. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds support for accuracy retrieval on fixed clocks.
It also adds a new dt property called 'clock-accuracy' to define the clock
accuracy.
This can be usefull for oscillator (RC, crystal, ...) definitions which are
always given an accuracy characteristic.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The clock accuracy is expressed in ppb (parts per billion) and represents
the possible clock drift.
Say you have a clock (e.g. an oscillator) which provides a fixed clock of
20MHz with an accuracy of +- 20Hz. This accuracy expressed in ppb is
20Hz/20MHz = 1000 ppb (or 1 ppm).
Clock users may need the clock accuracy information in order to choose
the best clock (the one with the best accuracy) across several available
clocks.
This patch adds clk accuracy retrieval support for common clk framework by
means of a new function called clk_get_accuracy.
This function returns the given clock accuracy expressed in ppb.
In order to get the clock accuracy, this implementation adds one callback
called recalc_accuracy to the clk_ops structure.
This callback is given the parent clock accuracy (if the clock is not a
root clock) and should recalculate the given clock accuracy.
This callback is optional and may be implemented if the clock is not
a perfect clock (accuracy != 0 ppb).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
'clk_si570_of_match' is always compiled in. Hence the
helper macro is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add support for using emev2 SMU clocks with DT
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=NhhY
-----END PGP SIGNATURE-----
Merge tag 'renesas-clock-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into clk-next-shmobile2
Renesas ARM based SoC Clock updates for v3.14
Add support for using emev2 SMU clocks with DT
- Add support for fclk-enable feature
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlK0N8wACgkQykllyylKDCGqjACeIK/TYdQHwqtYstkBWjZE5Poh
CskAmwd24c2c/Yd7gK68Vhv0Ip/a2KX4
=oBJ6
-----END PGP SIGNATURE-----
Merge tag 'zynq-clk-for-3.14-v2' of git://git.xilinx.com/linux-xlnx into clk-next
arm: Xilinx Zynq clk patches for v3.14
- Add support for fclk-enable feature
In some use cases Zynq's FPGA clocks are used as static clock
generators for IP in the FPGA part of the SOC for which no Linux driver
exists and would control those clocks. To avoid automatic
gating of these clocks in such cases a new property - fclk-enable - is
added to the clock controller's DT description to accomodate such use
cases. It's value is a bitmask, where a set bit results in enabling
the corresponding FCLK through the clkc.
FPGA clocks are handled following the rules below:
If an FCLK is not enabled by bootloaders, that FCLK will be disabled in
Linux. Drivers can enable and control it through the CCF as usual.
If an FCLK is enabled by bootloaders AND the corresponding bit in the
'fclk-enable' DT property is set, that FCLK will be enabled by the clkc,
resulting in an off by one reference count for that clock. Ensuring it
will always be running.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Extra semicolon is redundant. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
'vtwm_pll_ops' is local to this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
'of_cpu_clk_setup' is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk_sp810_timerclken_of_get is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
tegra_clk_periph_nodiv_ops is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Local variables used only in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk_frac_ops is local to this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a driver for SILabs 570, 571, 598, 599 programmable oscillators.
The devices generate low-jitter clock signals and are reprogrammable via
an I2C interface.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Device tree clock binding document for EMMA Mobile EV2 SMU,
And Common clock framework based implementation of it.
Following nodes are defined to describe clock tree.
- renesas,emev2-smu
- renesas,emev2-smu-clkdiv
- renesas,emev2-smu-gclk
These bindings are designed manually based on
19UH0037EJ1000_SMU : System Management Unit User's Manual
So far, reparent is not implemented, and is fixed to index #0.
Clock tree description is not included, and should be provided
by device-tree.
Signed-off-by: Takashi Yoshii <takasi-y@ops.dti.ne.jp>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
MSTP clocks are gate clocks controlled through a register that handles
up to 32 clocks. The register is often sparsely populated.
Those clocks are found on Renesas ARM SoCs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
DIV6 clocks are divider gate clocks controlled through a single
register. The divider is expressed on 6 bits, hence the name, and can
take values from 1/1 to 1/64.
Those clocks are found on Renesas ARM SoCs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The R-Car Gen2 SoCs (R8A7790 and R8A7791) have several clocks that are
too custom to be supported in a generic driver. Those clocks can be
divided in two categories:
- Fixed rate clocks with multiplier and divisor set according to boot
mode configuration
- Custom divider clocks with SoC-specific divider values
This driver supports both.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Fixes cpll control and lock register offset values for Exynos5420 SoC.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Enable common clock driver of Hi3620 SoC. clkgate-seperated driver is
used to support the clock gate that enable/disable/status registers
are seperated.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Those are mostly random fixes, except for one patch to the composite
clock that adds support for automatic reparenting.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=sWyX
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-for-3.13' of https://github.com/mripard/linux into clk-next-sunxi-rebase
Allwinner sunXi SoCs clock changes
Those are mostly random fixes, except for one patch to the composite
clock that adds support for automatic reparenting.
Conflicts:
drivers/clk/sunxi/clk-sunxi.c
In case of error, the function __clk_lookup() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
clk_round_rate() can be used by drivers to determine whether or not a
frequency is supported by the clock. The current Tegra clock driver
outputs an error message and a stacktrace when the requested rate isn't
supported. That's fine for clk_set_rate(), but it's confusing when all
the driver does is query whether or not a frequency is supported.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The function socfpga_clk_init() can support clocks that do not have a divider
register, but a fixed-divider that can be read from DTS. Therefore, the "reg"
property is not a failing condition for socfpga_clk_init().
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The required properties are not named "div" and "mult",
but rather "clock-div" and "clock-mult".
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[Maybe the third time will be the charm. -Alex]
If CONFIG_COMMON_CLK_DEBUG is defined, clk_debug_create_one() is
called to populate a debugfs directory with a few entries that are
common for all clock types.
If an error happens after creating the first one debugfs_remove() is
called on the clock's directory. The problem with this is that no
cleanup is done on the debugfs files already created in that
directory, so the directory never actually gets removed. This
problem is silently ignored.
Fix this by calling debugfs_remove_recursive() instead. Reset the
clk->dentry field to null afterward, to ensure it can't be mistaken
as a valid pointer.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The low-power DSI clocks are used during host-driven transactions on the
DSI bus. Documentation recommends that they be children of PLLP and run
at a frequency of at least 52 MHz.
Signed-off-by: Thierry Reding <treding@nvidia.com>
