If start_streaming fails, then the buffers must be given back to vb2 with state
QUEUED, not ERROR. Otherwise a WARN_ON will be generated.
In the disconnect it is pointless to call pwc_cleanup_queued_bufs() as stop_streaming()
will be called anyway.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the larger fifo found on sun5i and sun6i, having a separate
compatible for the ir found on sun5i & sun6i also is useful if we ever want
to add ir transmit support, because the sun5i & sun6i version do not have
transmit support.
Note this commits also adds checking for the end-of-packet interrupt flag
(which was already enabled), as the fifo-data-available interrupt flag only
gets set when the trigger-level is exceeded. So far we've been getting away
with not doing this because of the low trigger-level, but this is something
which we should have done since day one.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On sun6i the cir block is attached to the reset controller, add support
for de-asserting the reset if a reset controller is specified in dt.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Checkpatch complained about a few issues, like FSF address. Also,
multi-line comments are not following the Kernel CodingStyle.
While not too late, let's fix those issues.
Cc: John McMaster <johndmcmaster@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adds support for AmScope MU800 / ToupTek UCMOS08000KPB USB microscope camera.
Signed-off-by: John McMaster <johndmcmaster@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When converting to or from Y'CbCr and R'G'B' the Y offset depends
on the quantization range: it's 0 for full and 16 for limited range.
But in the code it was hardcoded to 16. This messed up the brightness
of the generated pattern.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
of_read_number() is defined in of.h but does not return an error code, so
that non-of implementation could simply return an error.
Temporarily work around this until of_read_number() can be replaced by
of_property_read_u64_array().
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We must unregister frontend first and after that driver itself. That
order went wrong after demod drivers were switched to kernel I2C
drivers, causing crashes.
Tested-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As rtl2832 driver support now I2C binding we will switch to that one.
Tested-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert that driver to I2C driver model.
Legacy DVB binding is left also for later removal...
Tested-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 1866123425.
The video_device debug field has been renamed to dev_debug, resulting in
a compilation failure. As v4l2 debugging is supposed to be controlled
through a sysfs attribute created by the v4l2 core, there's no need to
duplicate debug control through a module parameter. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The UVC spec is a bit vague wrt devices using bulk endpoints,
specifically, how to signal to a device to start streaming.
For devices using isoc endpoints, the sequence for start streaming is:
1) The host sends PROBE_CONTROL(SET_CUR) PROBE_CONTROL(GET_CUR)
2) Host selects desired config and calls COMMIT_CONTROL(SET_CUR)
3) Host selects an alt interface other then zero - e.g SELECT_ALTERNATE_INTERFACE(1)
4) The device starts streaming
However for devices using bulk endpoints, there must be *no* alt interface
other than setting zero. From the UVC spec:
"A VideoStreaming interface containing a bulk endpoint for streaming shall
support only alternate setting zero. Additional alternate settings containing
bulk endpoints are not permitted in a device that is compliant with the Video
Class specification."
So for devices using bulk endpoints, step #3 above is irrelevant, and thus
cannot be used as an indication for the device to start streaming.
So in practice, such devices start streaming immediately after a
COMMIT_CONTROL(SET_CUR).
In the uvc resume() handler, an unsolicited commit is sent, which causes
devices using bulk endpoints to start streaming unintentionally.
This patch modifies resume() handler to send a commit only if streaming
needs to be reestablished, i.e if the device was actually streaming before is
was suspended.
Signed-off-by: Aviv Greenberg <aviv.d.greenberg@intel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
LNE bit in VI6_DISP_IRQ_STA register are from the 0 bit to 4 bit.
This fixes bit position specified by VI6_DISP_IRQ_STA_LNE.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
LNEE bit in VI6_DISP_IRQ_ENB register are from the 0 bit to 4 bit.
This fixes bit position specified by VI6_DISP_IRQ_ENB_LNEE.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
According to the spec, the minimum input pixel size for BRU is 1px,
not 4px.
Signed-off-by: Takanari Hayama <taki@igel.co.jp>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the new logging functions from the hdmi module.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As per the suggestion of Thierry Reding rename
HDMI_AUDIO_CODING_TYPE_EXT_STREAM to HDMI_AUDIO_CODING_TYPE_EXT_CT to
be consistent with the CEA-861 spec.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When receiving video it is very useful to be able to unpack the InfoFrames.
Logging is useful as well, both for transmitters and receivers.
Especially when implementing the VIDIOC_LOG_STATUS ioctl (supported by many
V4L2 drivers) for a receiver it is important to be able to easily log what
the InfoFrame contains. This greatly simplifies debugging.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add new Video InfoFrame colorspace information introduced in HDMI 2.0
and new Audio Coding Extension Types, also from HDMI 2.0.
HDMI_CONTENT_TYPE_NONE was renamed to _GRAPHICS since that's what
it is called in CEA-861-F.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no need to jump to the 'err' label as we can simply return the error
code directly and make the code shorter.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The "i" variable is used as an offset into both the dev->vfd[] and the
dev->devtype->vdevs[] arrays. The second array is smaller so we should
use that as a limit instead of ARRAY_SIZE(dev->vfd). Also the original
check was off by one.
We should use a format string as well in case the ->name has any funny
characters and also to stop static checkers from complaining.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Improve g_tuner and add s_hw_freq_seek and enum_freq_bands support for cards
with TEA575x radio.
This allows signal/stereo detection and HW seek to work on these cards.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Split ioctl interface from enum_freq_bands, g_tuner and s_hw_freq_seek
functions and export them to be used in other drivers like bttv.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove tea575x-specific code from bttv and use the common driver instead.
Only set_frequency is implemented (signal/stereo detection or seek would
require more changes to bttv).
It works fine on Video Highway Xtreme (it actually makes the radio usable as
it currently cannot be tuned properly).
Miro/Pinnacle is untested but seems to be simple and should work.
However, I don't understand the Terratec Active Radio Upgrade code. The HW
seems to need IOR, IOW and CSEL signals that were taken from ISA bus on
older cards (IOR and IOW directly and CSEL from some address decoder) and
are emulated here using GPIOs. But the code manipulating these signals in
bttv seems to be broken - it never asserts the IOR signal. If anyone has
this HW, please test if I got that right.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit or error. This is obsolete meanwhile, the core will do it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove the function pvr2_hdw_cmd_powerdown() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Removes some functions that are not used anywhere:
test_read() edid_read_block() dpp_write() dpp_read()
esdp_write() esdp_read() cec_write_clr_set()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove the function vsp1_hsit_read() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove the function saa7134_queue() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove the function write_eeprom_byte() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Removes some functions that are not used anywhere:
vblanking() hblanking()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Based on versioncheck.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Based on versioncheck.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>
The semantic patch also changes the cast to long to a cast to unsigned
long in the data initializer, as unsigned long is the type of the data field.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-t.function = f;
-t.data = d;
-init_timer(&t);
+setup_timer(&t,f,d);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The videobuf_dma_init* and videobuf_dma_map() functions are no longer
used except in videobuf-dma-sg.c itself. Make them static.
These functions were abused in various drivers. All those drivers
have now been fixed, so by no longer exporting these functions
future abuse is now prevented.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove the function fm_rx_get_rds_system() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
To be future-proof and for better readability the time comparisons are
modified to use time_after() instead of plain, error-prone math.
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As mx53 is a dt-only architecture we can safely remove its entry from the
coda_platform_ids[] structure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUxbzlAAoJEHm+PkMAQRiGtqYIAJ8YlKX9cXKYmXx8/FncINH+
2erj94KyHG080R1uwSq1+7zXWCZUUlxiJnDnsup5rG0dImcicqgOE48oHax1aN6b
yHfPONkTjNJ1HYepuGC3YWCG9wIjPZQ5S8KHrwRjyVoE+ddhe9gWgvArA3jl/fW/
2fYNWekoRoMcRiNb4/w2weyOOBywdSVpmj0WYiwdztysG2ymw5hUXRHJhvSf1AFm
RQJfUHkhCOYpQGY7XFba/1uGhTJfOgDmYAfspAOLzmrXE/DJcCutsVdBZO+12fAL
nhGpM/PkRYxMvwzDKIUoG35qsymYOMqo54oXhr0S2JjyXTGdGmB6qHxIfqnV5Tk=
=O/Lr
-----END PGP SIGNATURE-----
Merge tag 'v3.19-rc6' into patchwork
This is needed in order to get the media fixes applied on -rc6.
Linux 3.19-rc6
* tag 'v3.19-rc6': (891 commits)
Linux 3.19-rc6
dm: fix handling of multiple internal suspends
hwmon: (i5500_temp) Convert to use ATTRIBUTE_GROUPS macro
hwmon: (i5500_temp) Convert to module_pci_driver
hwmon: (i5500_temp) Don't bind to disabled sensors
hwmon: (i5500_temp) Convert to devm_hwmon_device_register_with_groups
hwmon: (i5500_temp) New driver for the Intel 5500/5520/X58 chipsets
arm64: dts: add baud rate to Juno stdout-path
Revert "platform: x86: dell-laptop: Add support for keyboard backlight"
Revert "Documentation: Add entry for dell-laptop sysfs interface"
dm cache: fix problematic dual use of a single migration count variable
dm cache: share cache-metadata object across inactive and active DM tables
of/unittest: Overlays with sub-devices tests
KVM: x86: SYSENTER emulation is broken
KVM: x86: Fix of previously incomplete fix for CVE-2014-8480
arm64: dump: Fix implicit inclusion of definition for PCI_IOBASE
x86/tsc: Change Fast TSC calibration failed from error to info
x86/apic: Re-enable PCI_MSI support for non-SMP X86_32
x86, mm: Change cachemode exports to non-gpl
x86, tls: Interpret an all-zero struct user_desc as "no segment"
...
Conflicts:
drivers/media/pci/cx23885/cx23885.h
The debug parameter is not used anymore, as this module was
converted already to use dev_dbg().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Increase si2168 cmd execute timeout to prevent firmware load failures. Tests
shows it takes up to 52ms to load the 'dvb-demod-si2168-a30-01.fw' firmware.
Increase timeout to a safe value of 70ms.
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
