Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407180655.128771-2-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407180655.128771-1-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407180045.126952-1-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-10-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-9-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-8-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-7-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-6-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-5-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-4-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-3-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-2-krzysztof.kozlowski@linaro.org
Pin configuration property "input-enable" was used with the intention to
disable the output, but this is done by default by Linux drivers. Since
patch ("dt-bindings: pinctrl: qcom: tlmm should use output-disable, not
input-enable") the property is not accepted anymore.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407175807.124394-1-krzysztof.kozlowski@linaro.org
Add support for the Xiaomi Mi A3 (xiaomi-laurel-sprout). Here's a
summary on what's defined.
- dmesg output to bootloader preconfigured display
- USB
- UFS
- SD card
- SMD RPM regulators
- Volume Up, Down and Power buttons
- Thermistors
Signed-off-by: Lux Aliaga <they@mint.lgbt>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230306170817.3806-7-they@mint.lgbt
Add support for the Xiaomi Mi Pad 5 Pro CSOT variant. The CSOT variant
uses China Star Optoelectronics Technology (CSOT) panel based on NT36523
display controller.
Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323005925.23179-3-lujianhua000@gmail.com
Add nodes for BOE NT36523 panel found in xiaomi-elish. This panel
is a dual dsi mode panel and the dsi phy type is cphy.
Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323005925.23179-2-lujianhua000@gmail.com
There are two panel variants of xiaomi-elish, BOE and CSOT panels.
In order to support both panels, so split elish dts into common dtsi
and elish-boe dts.
Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323005925.23179-1-lujianhua000@gmail.com
Add an initial device tree for the QTI RB1 development board, based on
the QRB2210 (QCM2290 derivative) SoC. This device tree targets the SoM
revision 4, a.k.a. the Mass Production SKU.
To get a successful boot, run:
cat arch/arm64/boot/Image.gz arch/arm64/boot/dts/qcom/qrb2210-rb1.dtb >\
.Image.gz-dtb
mkbootimg \
--kernel .Image.gz-dtb \
--ramdisk some_initrd \
--output rb1-boot.img \
--pagesize 4096 \
--base 0x8000 \
--cmdline 'some cmdline'
fastboot boot rb1-boot.img
There's no dtbo or other craziness to worry about.
For the best dev experience, you can erase boot and use fastboot boot
everytime, so that the bootloader doesn't mess with you.
If you have a SoM revision 3 or older (there should be a sticker on it
with text like -r00, where r is the revision), you will need to apply
this additional diff:
aliases {
- serial0 = &uart0;
+ serial0 = &uart4;
/* UART connected to the Micro-USB port via a FTDI chip */
- &uart0 {
+ &uart4 {
That should however only concern preproduction boards.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230403-topic-rb1_qcm-v2-5-dae06f8830dc@linaro.org
Add an initial device tree for the QCM2290 low-end SoC, featuring 4
"customized" Cortex-A53 cores and up to 4 GiB of LPDDR(3/4X).
This revision brings support for:
- TSENS & thermal zones
- SDHCI1/2
- I2C, SPI, UART
- MPSS
- ADSP
- Wi-Fi
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230403-topic-rb1_qcm-v2-3-dae06f8830dc@linaro.org
Drop the qcom,snoc-host-cap-skip-quirk that was never introduced to
solve schema warnings.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406-topic-ath10k_bindings-v3-2-00895afc7764@linaro.org
Enable the SLPI DSP on the SHIFTPHONES SHIFT6mq phone with a
Qualcomm SDM845 SoC.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406173148.28309-6-me@dylanvanassche.be
Enable the SLPI DSP on the Oneplus 6 phone with a Qualcomm SDM845 SoC.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406173148.28309-5-me@dylanvanassche.be
Qualcomm SDM845 SoC features a SLPI DSP which uses FastRPC through
an allocated memory region to load files from the host filesystem
such as sensor configuration files.
Add a FastRPC node at /dev/fastrpc-sdsp and a DMA region, similar to
downstream, to allow userspace to communicate with the SLPI via the
FastRPC interface for initializing the sensors on the SLPI.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406173148.28309-4-me@dylanvanassche.be
Add the SLPI remoteproc to the SDM845 Qualcomm SoC which is responsible
for exposing the sensors connected to the SoC. The SLPI communicates
over GLink edge 'dsps' and is similar to other DSPs e.g. ADSP or CDSP.
This patch allows the SLPI to boot and expose itself over QRTR as
service 400.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406173148.28309-2-me@dylanvanassche.be
Drop the unnecessary mux{} level to make dtbs check happy.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407-topic-msm_dtb-v1-6-6efb4196f51f@linaro.org
Fix the node name to make dtbs_check happy:
qcom/apq8016-sbc.dtb: pmic@0: 'extcon@1300' does not match any of the
regexes: '(.*)?(wled|leds)@[0-9a-f]+$', '^adc-tm@[0-9a-f]+$',
'^adc@[0-9a-f]+$', '^audio-codec@[0-9a-f]+$', '^charger@[0-9a-f]+$',
'^mpps@[0-9a-f]+$', '^nvram@[0-9a-f]+$', '^rtc@[0-9a-f]+$',
'^temp-alarm@[0-9a-f]+$', '^usb-detect@[0-9a-f]+$',
'^usb-vbus-regulator@[0-9a-f]+$', '^vibrator@[0-9a-f]+$',
'gpio@[0-9a-f]+$', 'pinctrl-[0-9]+', 'pon@[0-9a-f]+$'
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407-topic-msm_dtb-v1-5-6efb4196f51f@linaro.org
Fix the following schema warning:
gic-its@17a40000: False schema does not allow {'compatible':
['arm,gic-v3-its'], 'msi-controller': True, '#msi-cells': [[1]],
'reg': [[0, 396623872, 0, 131072]], 'status': ['disabled']}
And reorder the properties to be more in order with all other nodes.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407-topic-msm_dtb-v1-4-6efb4196f51f@linaro.org
Cheza's SPI flash hookups (qspi) are exactly the same as trogdor's.
Apply the same solution that's described in the patch ("arm64: dts:
qcom: sc7180: Fix trogdor qspi pin config")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.14.I82951106ab8170f973a4c1c7d9b034655bbe2f60@changeid
Similar to sc7180 (see the patch ("arm64: dts: qcom: sc7180: Fix
trogdor qspi pin config")), we should adjust the qspi pin config for
sc7280.
I won't re-describe all the research/arguments in the sc7180 patch
here, but there are a few differences for sc7280 worth noting:
1. On herobrine the SPI flash (qspi) is wired up differently on the
board. Rather than Cr50 and the AP being wired directly together,
there's actually a mux that will _either_ connect the AP to the
flash or Cr50 to the flash. This means that the internal pulls on
Cr50 don't affect us and we should enable our own pulldowns.
2. On herobrine, EEs added an external pulldown on the MISO line. The
argument in the schematic said that we added it (but not one on
MOSI and CLK) because Cr50 already enabled pulldowns on MOSI and
CLK. ...though, as per #1, those Cr50 pulldowns would only affect
the line when the mux was swung to Cr50.
The ironic result of #1 and #2 is that the external pulldowns on
CLK/MISO/MOSI on herobrine are _exactly opposite_ of the ones on
trogdor.
3. While I still don't have the actual exact schematics for all
variants of IDP/CRD that were produced, I have some reference
schematics that give me a belief of how the qspi is hooked up
there. From this, I'm fairly certain that all of the older variants
of IDP/CRD either have a pulldown on the CLK/MOSI/MISO lines (maybe
through a direct connect to Cr50) or have no pull (in other words,
they don't have a pullup). I'll go ahead and enable internal
pulldowns on all the lines since that won't hurt to double-pull if
there's an external pulldown and it's nice to have a pulldown if
there's nothing external. Note that this only affects _older_
CRDs. Newer revs are considered "herobrine" (see the hoglin/zoglin
device trees).
4. I didn't find the same strange "auto-switch-to-keeper" at suspend
when probing on sc7280. Whatever pulls (or lack thereof) I left at
suspend time seemed to persist into suspend.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.13.Ib44c3e417c414a4227db8def75ded37ad368212c@changeid
In commit 7ec3e67307 ("arm64: dts: qcom: sc7180-trogdor: add initial
trogdor and lazor dt") we specified the pull settings on the boot SPI
(the qspi) data lines as pullups to "park" the lines. This seemed like
the right thing to do, but I never really probed the lines to confirm.
Since that time, I've done A LOT of research, experiements and poking
of the lines with a voltmeter.
A first batch of discoveries:
- There is an external pullup on CS (clearly shown on schematics)
- There are weak external pulldowns on CLK/MOSI (believed to be Cr50's
internal pulldowns)
- There is no pull on MISO.
- When qspi isn't actively transferring it still drives CS, CLK, and
MOSI. CS and MOSI are driven high and CLK is driven low. It does not
drive MISO and (if no internal pulls are enabled) the line floats.
The above means that it's good to have some sort of pull on MISO, at
the very least. The pullup that we had before was actually fine (and
my voltmeter confirms that it actually affected the state of the pin)
but a pulldown would work equally well (and would match MOSI and CLK
better).
The above also means that we could save a tiny bit of power (not
measurable by my setup) by setting up a sleep state for these pins. If
nothing else this prevents us from driving high against Cr50's
internal pulldown on MOSI. However, Qualcomm has also asserted in the
past that it burns a little extra power to drive a pin, especially
since these are configured with a slightly higher drive strength
Let's fix all this. Since the external pulls are different for the two
data lines, we'll split them into separate configs. Then we'll change
the MISO pin to a pulldown and add a sleep state.
On a slightly tangental (but not totally unrelated note), I also
discovered some interesting things with these pins in suspend. First,
I found that if we don't switch the pins to GPIO that the qspi
peripheral continues to drive them in suspend. That'll be solved by
what we're already doing above. Second, I found that something in the
system suspend path (after Linux stops running) reconfigures these
pins so that they don't have their normal pulls enabled but instead
change to "keepers" (bias-bus-hold in DT speak). If a pin was floating
before we entered suspend then it would stop floating. I found that I
could manually pull a pin to a different level and then probe it and
it would stay there. This is exactly keeper behavior. With the
solution we have the switch to "keeper" doesn't matter too much but
it's good to document.
While talking about "keepers", it can also be noted that I found that
the "keepers" on these pins were at least enough to win a fight
against Cr50's internal pulls. That means it's best to make sure that
the state of the pins are already correct before the mysterious
transition to a keeper. Otherwise we'll burn (a small amount of) power
in S3 via this fight. Luckily with the current solution we don't hit
this case.
NOTE: I've left "sc7180-idp" behavior totally alone in this patch. I
didn't add a sleep state and I didn't change any pulls--I just adapted
it to the fact that the data lines have separate configs. Qualcomm
doesn't provide me with schematics for IDP and thus I don't actually
know how the pulls are configured. Since this is just a development
platform and worked well enough, it seems safer to leave it alone.
Dependencies:
- This patch has a hard dependency on ("pinctrl: qcom: Support
OUTPUT_ENABLE; deprecate INPUT_ENABLE"). Something in the boot code
seemed to have been confused and thought it needed to set the
"OUTPUT ENABLE" bit for these pins even though it was using them as
SPI. Thus if we don't honor the "output-disable" property we could
end up driving the SPI pins while in sleep mode.
- In general, it's probably best not to backport this to a kernel that
doesn't have commit d21f4b7ffc ("pinctrl: qcom: Avoid glitching
lines when we first mux to output"). That landed a while ago, but
it's still good to be explicit in case someone was backporting. If
we don't have that then there might be a glitch when we first switch
over to GPIO before we disable the output.
- This patch _doesn't_ really have any dependency on the qspi driver
patch that supports setting the pinctrl sleep state--they can go in
either order. If we define the sleep state and the driver never
selects it that's fine. If the driver tries to select a sleep state
that we don't define that's fine.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.12.I6f03f86546e6ce9abb1d24fd9ece663c3a5b950c@changeid
As talked about in the patch ("dt-bindings: pinctrl: qcom: tlmm should
use output-disable, not input-enable"), using "input-enable" in
pinctrl states for Qualcomm TLMM pinctrl devices was either
superfluous or there to disable a pin's output.
Looking at cheza
* ec_ap_int_l, h1_ap_int_odl: Superfluous. The pins will be configured
as inputs automatically by the Linux GPIO subsystem (presumably the
reference for other OSes using these device trees).
* bios_flash_wp_l: Superfluous. This pin is exposed to userspace
through the kernel's GPIO API and will be configured automatically.
That means that in none of the cases for cheza did we need to change
"input-enable" to "output-disable" and we can just remove these
superfluous properties.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.11.Ia439c29517b1c0625325a54387b047f099d16425@changeid
As talked about in the patch ("dt-bindings: pinctrl: qcom: tlmm should
use output-disable, not input-enable"), using "input-enable" in
pinctrl states for Qualcomm TLMM pinctrl devices was either
superfluous or there to disable a pin's output.
Looking at the sc7280-idp-ec-h1.dtsi file:
* ap_ec_int_l, h1_ap_int_odl: Superfluous. The pins will be configured
as inputs automatically by the Linux GPIO subsystem (presumably the
reference for other OSes using these device trees).
That means that in none of the cases for sc7280-idp-ec-h1.dtsi did we
need to change "input-enable" to "output-disable" and we can just
remove these superfluous properties.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.10.I1343c20f4aaac8e2c1918b756f7ed66f6ceace9c@changeid
As talked about in the patch ("dt-bindings: pinctrl: qcom: tlmm should
use output-disable, not input-enable"), using "input-enable" in
pinctrl states for Qualcomm TLMM pinctrl devices was either
superfluous or there to disable a pin's output.
Looking at trogdor:
* ap_ec_int_l, fp_to_ap_irq_l, h1_ap_int_odl, p_sensor_int_l:
Superfluous. The pins will be configured as inputs automatically by
the Linux GPIO subsystem (presumably the reference for other OSes
using these device trees).
* bios_flash_wp_l: Superfluous. This pin is exposed to userspace
through the kernel's GPIO API and will be configured automatically.
That means that in none of the cases for trogdor did we need to change
"input-enable" to "output-disable" and we can just remove these
superfluous properties.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.9.I94dbc53176e8adb0d7673b7feb2368e85418f938@changeid
The l13a rail on trogdor devices has always been intended to be
always-on on both S0 and S3. Different trogdor variants use l13a in
slightly different ways, but the overall theme is that it's a 1.8V
rail that the board uses for things that it wants powered in on S0 and
S3. On many boards this includes the boot SPI (AKA qspi).
For all intents and purposes this patch is actually a no-op since
something else in the system seems to already be keeping the rail on
all the time (confirmed via multimeter). That "something else" was
postulated to be the modem but the rail is on / stays on even without
the modem/wifi coming up so it's likely the boot config. In any case,
making the fact that this is always-on explicit seems like a good
idea.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.4.I9f47a8a53eacff6229711a827993792ceeb36971@changeid
There are 4 qspi data pins: data0, data1, data2, and data3. Currently
we have a shared pin state for data0 and data1 (2 lane config) and a
pin state for data2 and data3 (you'd enable both this and the 2 lane
state for 4 lanes). The second state is obviously misnamed. Fix it.
Fixes: e1ce853932 ("arm64: dts: qcom: sdm845: Add qspi (quad SPI) node")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.3.I88528d037b7fda4e53a40f661be5ac61628691cd@changeid
There are 4 qspi data pins: data0, data1, data2, and data3. Currently
we have a shared pin state for data0 and data1 (2 lane config) and a
pin state for data2 and data3 (you'd enable both this and the 2 lane
state for 4 lanes). The second state is obviously misnamed. Fix it.
Fixes: 7720ea001b ("arm64: dts: qcom: sc7280: Add QSPI node")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.2.I4043491bb24b1e92267c5033d76cdb0fe60934da@changeid
There are 4 qspi data pins: data0, data1, data2, and data3. Currently
we have a shared pin state for data0 and data1 (2 lane config) and a
pin state for data2 and data3 (you'd enable both this and the 2 lane
state for 4 lanes). The second state is obviously misnamed. Fix it.
Fixes: ba3fc64963 ("arm64: dts: sc7180: Add qupv3_0 and qupv3_1")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.1.Ifc1b5be04653f4ab119698a5944bfecded2080d6@changeid
There are some interop issues seen across a few DP monitors with
HBR3 and herobrine boards where the DP display stays blank with hbr3.
This is still under investigation but in preparation for supporting
higher resolutions, its better to disable HBR3 till the issues are
root-caused as there is really no guarantee which monitors will show
the issue and which would not.
This can be enabled back after successful validation across more DP
sinks.
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230329233416.27152-1-quic_abhinavk@quicinc.com
The DSA framework has got more picky about always having a phy-mode
for the CPU port. The SoC Ethernet is being configured to
10gbase-r. Set the switch phy-mode based on this. Additionally, the
SoC Ethernet is using in-band signalling to determine the link speed,
so add same parameter to the switch.
Additionally, the cpu label has never actually been used in the
binding, so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The GL-MV1000 (Brume) is a small form-factor gateway router.
It is based on the Marvell Armada 88F3720 SOC (1GHz), has 3 gigabit ethernet ports, 1 GB RAM, 16M SPI flash, 8GB eMMC and an uSD slot, as well as an USB 2.0 type A and an USB 3.0 type C port.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
CC: Pali <pali@kernel.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Bindings expect thermal node names to end with '-thermal':
armada-8040-db.dtb: thermal-zones: 'ap-thermal-cpu0', ... do not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Armada 7040 uses a rather small 15MB memory window for every PCI adapter,
however this is not sufficient for Qualcomm QCA6390 802.11ax cards that
are shipped along with the OpenWrt WLAN model of MOCHAbin as ath11k
requires at least 16MB of memory.
So, similar to what MACCHIATOBin has been doing for years, lets move
to using the second PCIe 2 memory window and expand it to 128MB to
make it future proof.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Add the Low Power Audio SubSystem (LPASS) / ADSP audio codec macros on
Qualcomm SM8550. The nodes are very similar to SM8450, except missing
NPL clock which is not exposed on SM8550 and should not be touched.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230310134925.514125-1-krzysztof.kozlowski@linaro.org
Currently, most of the Qualcomm SoCs specify both "iommus" and "iommu-map"
properties for the PCIe nodes. First one passes the SMR mask to the iommu
driver and the latter specifies the SID for each PCIe device.
But with "iommus" property, the PCIe controller will be added to the
iommu group along with the devices. This makes no sense because the
controller will not initiate any DMA transaction on its own. And moreover,
it is not strictly required to pass the SMR mask to the iommu driver. If
the "iommus" property is not present, then the default mask of "0" would be
used which should work for all PCIe devices.
On the other side, if the SMR mask specified doesn't match the one expected
by the hypervisor, then all the PCIe transactions will end up triggering
"Unidentified Stream Fault" by the SMMU.
So to get rid of these hassles and also prohibit PCIe controllers from
adding to the iommu group, let's remove the "iommus" property from PCIe
nodes.
Reported-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-arm-msm/20230227195535.GA749409-robh@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230308075648.134119-1-manivannan.sadhasivam@linaro.org
The parent controller for both interrupts is GIC, so no need for
interrupts-extended.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230405060906.143058-5-krzysztof.kozlowski@linaro.org
The parent controller for the interrupt is GIC, so no need for
interrupts-extended.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230405060906.143058-4-krzysztof.kozlowski@linaro.org
The parent controller for both interrupts is GIC, so no need for
interrupts-extended.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230405060906.143058-3-krzysztof.kozlowski@linaro.org
Use labels, instead of comments, for Soundwire controllers. Naming them
is useful, because they are specialized and have also naming in
datasheet/programming guide.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230405060906.143058-2-krzysztof.kozlowski@linaro.org
Use labels, instead of comments, for Soundwire controllers. Naming them
is useful, because they are specialized and have also naming in
datasheet/programming guide.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230405060906.143058-1-krzysztof.kozlowski@linaro.org
Add LCDIF scanout engine and DSIM bridge nodes for i.MX8M Plus.
This makes the DSI display pipeline available on this SoC.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add LCDIF scanout engine and DSIM bridge nodes for i.MX8M Nano.
This makes the DSI display pipeline available on this SoC.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add LCDIF scanout engine and DSIM bridge nodes for i.MX8M Mini.
This makes the DSI display pipeline available on this SoC.
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are cadence usb3.0 controller in 8qxp and 8qm.
Add usb3 node at common connect subsystem.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
'#clock-cells' is a dependency of 'clock-output-names', following
binding doc, add it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8MP includes the same GPT blocks as the i.MX6DL. Add all 6
instances.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is an NXP downstream property. And no binding doc, and no
driver use this property. So drop it
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Anbernic and Odroid Go have different panels and take differently
named supplies, so move all the supplies to DTS defining actual panel to
fix warnings like:
rk3326-odroid-go3.dtb: panel@0: 'IOVCC-supply' is a required property
rk3326-odroid-go3.dtb: panel@0: 'iovcc-supply', 'vdd-supply' do not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230326204520.80859-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Anbernic and Odroid Go have different panels and take differently
named supplies, so move all the supplies to DTS defining actual panel to
fix warnings like:
rk3326-odroid-go3.dtb: panel@0: 'IOVCC-supply' is a required property
rk3326-odroid-go3.dtb: panel@0: 'iovcc-supply', 'vdd-supply' do not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230326204520.80859-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The panel bindings expect to have only one port, thus they do not allow
to use "ports" node:
rk3399-rockpro64.dtb: panel@0: 'ports' does not match any of the regexes: 'pinctrl-[0-9]+'
There is only one endpoint, so use simpler form without "reg".
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230326204520.80859-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The panel bindings expect to have only one port, thus they do not allow
to use "ports" node:
rk3399-pinebook-pro.dtb: edp-panel: 'ports' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230326204520.80859-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the necessary DT nodes for the Rock 5B board to enable the analog
audio support provided by the Everest Semi ES8316 codec.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Christopher Obbard <chris.obbard@collabora.com>
Link: https://lore.kernel.org/r/20230402095054.384739-6-cristian.ciocaltea@collabora.com
[adapted to the fan addition I applied slightly earlier]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In addition to the five I2S/PCM/TDM controllers and the two I2S/PCM
controllers shared between the RK3588 and RK3588S SoCs, RK3588 provides
another group of four I2S/PCM/TDM controllers.
Add the DT nodes corresponding to the additional controllers.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230402095054.384739-5-cristian.ciocaltea@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There are five I2S/PCM/TDM controllers and two I2S/PCM controllers
embedded in the RK3588 and RK3588S SoCs.
Add the DT nodes corresponding to the above mentioned Rockchip
controllers.
Also note RK3588 SoC contains four additional I2S/PCM/TDM controllers,
which are handled via a separate patch.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230402095054.384739-4-cristian.ciocaltea@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The clock rate for PLL_PPLL has been wrongly initialized to 100 MHz
instead of 1.1 GHz. Fix it.
Fixes: c9211fa260 ("arm64: dts: rockchip: Add base DT for rk3588 SoC")
Reported-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230402095054.384739-3-cristian.ciocaltea@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Since commit df4fdd0db4 ("dt-bindings: firmware: arm,scmi: Restrict
protocol child node properties") the following dtbs_check warning is
shown:
rk3588-rock-5b.dtb: scmi: protocol@14: Unevaluated properties are not
allowed ('assigned-clock-rates', 'assigned-clocks' were unexpected)
Because adding the missing properties to firmware/arm,scmi.yaml binding
document was not an acceptable solution, move SCMI_CLK_CPUB01 and
SCMI_CLK_CPUB23 assigned clocks to the related CPU nodes and also add
the missing SCMI_CLK_CPUL.
Additionally, adjust frequency to 816 MHz for all the above mentioned
assigned clocks, in order to match the firmware defaults.
Suggested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230402095054.384739-2-cristian.ciocaltea@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add thermal sensor IP, which allows monitoring temperatures at
seven different places in the SoC:
* Chip Center
* CPU Cluster 1 (Dual A76 "Big" Cores)
* CPU Cluster 2 (Dual A76 "Big" Cores)
* CPU Cluster 0 (Quad A55 "Little" Cores)
* Power Domain Center
* Graphics Processing Unit
* Neural Processing Unit
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230404154429.51601-1-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the necessary DT changes for the Rock 5B board to enable support for
the PWM controlled heat sink fan.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Christopher Obbard <chris.obbard@collabora.com>
Link: https://lore.kernel.org/r/20230404173807.490520-3-cristian.ciocaltea@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The property should be off-on-delay-us, not off-on-delay
Fixes: a39ed23bdf ("arm64: dts: freescale: add initial support for verdin imx8m plus")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The property should be off-on-delay-us, not off-on-delay
Fixes: 6a57f224f7 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The osc_32k supports #clock-cells as 0, using an id is wrong, drop it.
Fixes: a6a355ede5 ("arm64: dts: imx8mm-evk: Add 32.768 kHz clock to PMIC")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The TX2 SoM's SDIO WiFI card is connected via mmc@3440000 however it does
not look like the upstream kernel is even bothering to power this (and
the regulator framework shuts down this power rail post kernel init).
The issue seems to be a missing link for vccq from the MAX77620 PMIC's LDO5
which is labeled vddio_sdmmc3 (and not used anywhere else) to the mmc@3440000
node to ensure there is at leasr bus power.
Note this does not fix the WiFi issue on upstream kernels, there is still
something else missing that gets the BCM WiFi device to detect properly.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the USB Type-C controller that is present on the Jetson AGX Orin
board. The ports for the Type-C controller are not populated yet, but
will be added later once the USB host and device support for Jetson AGX
Orin is enabled.
This is based upon a patch from Wayne Chang <waynec@nvidia.com>.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Lenovo Thinkpad X13s has a WCN6855 Bluetooth controller on uart2,
add this.
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230326233812.28058-5-steev@kali.org
Set line names for GPIO lines exposed by PMICs on sa8775p-ride.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-16-brgl@bgdev.pl
Add GPIO controller nodes to PMICs that have the GPIO hooked up on
sa8775p-ride.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-15-brgl@bgdev.pl
Add the thermal zones and associated alarm nodes for the PMICs that have
them hooked up on sa8775p-ride.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-12-brgl@bgdev.pl
Add the power key node under the PON node for PMIC #0 on sa8775p.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-10-brgl@bgdev.pl
Add a new .dtsi file for sa8775p PMICs and add the four PMICs interfaced
to the SoC via SPMI. Enable the PMICs for sa8775p-ride.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-8-brgl@bgdev.pl
Sort all children of the soc node by the first address in their reg
property. This was mostly already the case but there were some nodes
that didn't follow it so fix it now for consistency.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-3-brgl@bgdev.pl
The file has inconsistent padding of the address part of soc node
children's reg properties. Fix it.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-2-brgl@bgdev.pl
The pmk8280 PMIC PON peripheral is gen3 and uses two sets of registers;
hlos and pbs.
This specifically fixes the following error message during boot when the
pbs registers are not defined:
PON_PBS address missing, can't read HW debounce time
Note that this also enables the spurious interrupt workaround introduced
by commit 0b65118e6b ("Input: pm8941-pwrkey - add software key press
debouncing support") (which may or may not be needed).
Fixes: ccd3517faf ("arm64: dts: qcom: sc8280xp: Add reference device")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org> #Thinkpad X13s
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327122948.4323-1-johan+linaro@kernel.org
The bindings expect second Soundwire interrupt to be "wakeup" (Linux
driver takes by index):
sc8280xp-crd.dtb: soundwire-controller@3330000: interrupt-names:1: 'wakeup' was expected
Fixes: c18773d162 ("arm64: dts: qcom: sc8280xp: add SoundWire and LPASS")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230403132328.61414-1-krzysztof.kozlowski@linaro.org
Add the properties to ensure the ever so delicate touchscreen setup
matches downstream.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-tama_disp-v3-3-2b1567c039d7@linaro.org
Add required pins and RMI4 node to the common DT and remove it
from Akatsuki, as it uses a different touch.
Since the panels are super high tech proprietary incell, they
need to be handled with very precise timings. As such the panel
driver sets up the power rails and GPIOs and the touchscreen
driver *has to* probe afterwards.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-tama_disp-v3-2-2b1567c039d7@linaro.org
Add required nodes to support display on XZ2/XZ2c. XZ3 has a
different power rail setup and needs to be handled separately.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-tama_disp-v3-1-2b1567c039d7@linaro.org
Follow other dtses and pad regs to 8 digits.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230325112852.18841-4-a39.skl@gmail.com
Property phy_mode according to binding checker does not exist,
drop it.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230325112852.18841-3-a39.skl@gmail.com
Provide clocks from dsi_phy to gcc, this will make
sure we don't fallback to global name lookup.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230325112852.18841-2-a39.skl@gmail.com
Assign RPM_SMD_XO_CLK_SRC from rpmcc in place
of fixed-clock where possible.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230325112852.18841-1-a39.skl@gmail.com
Fixes the following DT bindings check error:
domain-idle-states: cluster-sleep-0: 'idle-state-name', 'local-timer-stop' do not match any of the regexes:
'pinctrl-[0-9]+'
domain-idle-states: cluster-sleep-1: 'idle-state-name', 'local-timer-stop' do not match any of the regexes:
'pinctrl-[0-9]+'
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323-topic-sm8450-upstream-dt-bindings-fixes-v2-2-0ca1bea1a843@linaro.org
Use the correct fallback compatible for the BWMONv4 with merged global and
monitor register spaces.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230304-topic-ddr_bwmon-v3-7-77a050c2fbda@linaro.org
Drop the incorrect msm8998 fallback and use the new qcom,sdm845-cpu-bwmon
compatible to distinguish the CPU BWMON found on this platform.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230304-topic-ddr_bwmon-v3-6-77a050c2fbda@linaro.org
Use the correct fallback compatible for the BWMONv4 with merged global and
monitor register spaces.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230304-topic-ddr_bwmon-v3-5-77a050c2fbda@linaro.org
Use the correct fallback compatible for the BWMONv4 with merged global and
monitor register spaces.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230304-topic-ddr_bwmon-v3-4-77a050c2fbda@linaro.org
With the gpio-line-names in place coming from SONY themselves, we can
now make the pin nodes and their labels to more closely resemble the
actual thing. 4k has been renamed to four_k due to dtc limitations.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314-topic-yoshino_gpio-v2-2-4cb80e187e38@linaro.org
Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).
Add these to the Yoshino devices DTs to better document the hardware.
Lilac and Poplar have identical pin assignments.
Diff between these two and maple:
TLMM:
- "NC",
+ "TS_VDDIO_EN",
PMI8998:
- "NC"
+ "USB_SWITCH_SEL"
- "NC"
+ "4K_DISP_DCDC_EN"
PM8005:
- "NC"
+ "EAR_EN"
Which is probably due to Maple being designed and released quite a bit
earlier than the other two and it having a super high tech true-4K
display.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314-topic-yoshino_gpio-v2-1-4cb80e187e38@linaro.org
The Poco F1 has a single color white notification LED. Enable the
Qualcomm Light Pulse Generator (LPG) driver based notification LED.
Signed-off-by: Joel Selvaraj <joelselvaraj.oss@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313154226.136726-1-joelselvaraj.oss@gmail.com
Add a DT node for Last level cache (aka. system cache) controller
which provides control over the last level cache present on QDU1000
and QRU1000 SoCs.
Signed-off-by: Komal Bajaj <quic_kbajaj@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313125731.17745-1-quic_kbajaj@quicinc.com
The PMIC regulators are not supposed to have unit addresses.
Fixes: 2317b87a2a ("arm64: dts: qcom: db820c: Add vdd_gfx and tie it into mmcc")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-8-krzysztof.kozlowski@linaro.org
The PMIC regulators are not supposed to have unit addresses.
Fixes: 60b214effb ("arm64: dts: qcom: msm8994-octagon: Configure regulators")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-7-krzysztof.kozlowski@linaro.org
The PMIC regulators are not supposed to have unit addresses.
Fixes: e9783584c9 ("arm64: dts: qcom: msm8994-kitakami: Add VDD_GFX regulator")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-6-krzysztof.kozlowski@linaro.org
This reverts commit 46546f2882 because it
mistakenly took PMIC pinctrl/GPIO as TLMM. The TLMM pinctrl uses "gpio"
function, but PMIC uses "normal", so original code was correct:
msm8998-oneplus-cheeseburger.dtb: pmic@2: gpio@c000:button-backlight-state: 'oneOf' conditional failed, one must be fixed:
'gpio' is not one of ['normal', 'paired', 'func1', 'func2', 'dtest1', 'dtest2', 'dtest3', 'dtest4', 'func3', 'func4']
Fixes: 46546f2882 ("arm64: dts: qcom: msm8998-oneplus-cheeseburger: fix backlight pin function")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-5-krzysztof.kozlowski@linaro.org
The hid-over-i2c takes VDD, not VCC supply. Fix copy-pasta from other
boards which use elan,ekth3000 with valid VCC:
sc7180-trogdor-pazquel360-lte.dtb: trackpad@15: 'vcc-supply' does not match any of the regexes: 'pinctrl-[0-9]+'
Fixes: fb69f6adaf ("arm64: dts: qcom: sc7180: Add pazquel dts files")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-4-krzysztof.kozlowski@linaro.org
The hid-over-i2c takes VDD, not VCC supply. Fix copy-pasta from other
boards which use elan,ekth3000 with valid VCC:
sc7180-trogdor-lazor-limozeen-nots-r4.dtb: trackpad@2c: 'vcc-supply' does not match any of the regexes: 'pinctrl-[0-9]+'
Fixes: 2c26adb8db ("arm64: dts: qcom: Add sc7180-lazor-limozeen skus")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-3-krzysztof.kozlowski@linaro.org
The hid-over-i2c takes VDD, not VCC supply. Fix copy-pasta from other
Herobrine boards which use elan,ekth3000 with valid VCC:
sc7280-herobrine-villager-r1-lte.dtb: trackpad@2c: 'vcc-supply' does not match any of the regexes: 'pinctrl-[0-9]+'
Fixes: ee2a621160 ("arm64: dts: qcom: sc7280: Add device tree for herobrine villager")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-2-krzysztof.kozlowski@linaro.org
gpio-key bindings expect children to be named with generic prefix:
sda660-inforce-ifc6560.dtb: gpio-keys: 'volup' does not match any of the regexes: ...
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-1-krzysztof.kozlowski@linaro.org
This commit adds support for the uz801 v3.0 WiFi/LTE dongle made by
Henan Yiming Technology Co., Ltd. based on MSM8916.
Note: The original firmware does not support 64-bit OS. It is necessary
to flash 64-bit TZ firmware to boot arm64.
Currently supported:
- All CPU cores
- Buttons
- LEDs
- Modem
- SDHC
- USB Device Mode
- UART
Signed-off-by: Yang Xiwen <forbidden405@foxmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/tencent_62395CA0D608DD0078DD3D889F6E4E22BA05@qq.com
On MSM8916 the wireless connectivity functionality (WiFi/Bluetooth) is
split into the digital part inside the SoC and the analog RF part inside
a supplementary WCN36xx chip. For MSM8916, three different options
exist:
- WCN3620 (WLAN 802.11 b/g/n 2.4 GHz + Bluetooth)
- WCN3660B (WLAN 802.11 a/b/g/n 2.4/5 GHz + Bluetooth)
- WCN3680B (WLAN 802.11ac 2.4/5 GHz + Bluetooth)
Choosing one of these is up to the board vendor. This means that the
compatible belongs into the board-specific DT part so people porting
new boards pay attention to set the correct compatible.
Right now msm8916.dtsi sets "qcom,wcn3620" as default compatible,
which does not work at all for boards that have WCN3660B or WCN3680B.
Remove the default compatible from msm8196.dtsi and move it to the board
DT as follows:
- Boards with only &pronto { status = "okay"; } used the default
"qcom,wcn3620" so far. They now set this explicitly for &wcnss_iris.
- Boards with &pronto { ... iris { compatible = "qcom,wcn3660b"; }};
already had an override that just moves to &wcnss_iris now.
- For msm8916-samsung-a2015-common.dtsi the WCN compatible differs for
boards making use of it (a3u: wcn3620, a5u: wcn3660b, e2015: wcn3620)
so the definitions move to the board-specific DT part.
Since this requires touching all the board DTs, use this as a chance to
name the WCNSS-related labels consistently, so everything is grouped
properly when sorted alphabetically.
No functional change, just clean-up for more clarity & easier porting.
Aside from ordering the generated DTBs are identical.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230309091452.1011776-1-stephan.gerhold@kernkonzept.com
Jetson AGX Orin has onboard RT5640 audio codec. This patch adds the
codec device node and the bindings to I2S1 interface.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
- Add USB3 support for the RZ/V2M SoC and the RZ/V2M Evaluation Kit 2.0,
- Add uSD card and eMMC support for the RZ/V2M Evaluation Kit 2.0,
- Add CAN-FD, thermal, GMSL2 video capture, and sound support for the
R-Car V4H SoC and the White-Hawk development board,
- Add PMU support for the RZ/G2UL, RZ/G2L{,C}, and RZ/V2L SoCs,
- Drop support for the obsolete R-Car H3 ES1.* (R8A77950) SoC,
- Add I2C EEPROM support for the Atmark Techno Armadillo-800-EVA, and
the Renesas Condor and ULCB development boards,
- Miscellaneous fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCZCFQ5wAKCRCKwlD9ZEnx
cGqBAQDWxWvL3fy+srYshTn4KoTmoJ1T00SQDNvRoN0r97N8bAD+Mw3hhApGtn9O
SpnBwOSvQeYzMLrG9NczM5JJu1eW8Qs=
=eROn
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=HxdL
-----END PGP SIGNATURE-----
Merge tag 'renesas-dts-for-v6.4-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into soc/dt
Renesas DTS updates for v6.4
- Add USB3 support for the RZ/V2M SoC and the RZ/V2M Evaluation Kit 2.0,
- Add uSD card and eMMC support for the RZ/V2M Evaluation Kit 2.0,
- Add CAN-FD, thermal, GMSL2 video capture, and sound support for the
R-Car V4H SoC and the White-Hawk development board,
- Add PMU support for the RZ/G2UL, RZ/G2L{,C}, and RZ/V2L SoCs,
- Drop support for the obsolete R-Car H3 ES1.* (R8A77950) SoC,
- Add I2C EEPROM support for the Atmark Techno Armadillo-800-EVA, and
the Renesas Condor and ULCB development boards,
- Miscellaneous fixes and improvements.
* tag 'renesas-dts-for-v6.4-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (30 commits)
arm64: dts: renesas: r8a779a0: Update CAN-FD to R-Car Gen4 compatible value
arm64: dts: renesas: ulcb: Add I2C EEPROM for PMIC
arm64: dts: renesas: condor: Add I2C EEPROM for PMIC
ARM: dts: armadillo800eva: Add I2C EEPROM for MAC address
arm64: dts: renesas: Remove R-Car H3 ES1.* devicetrees
arm64: dts: renesas: white-hawk: Add R-Car Sound support
arm64: dts: renesas: r8a779g0: R-Car Sound support
arm64: dts: renesas: r9a07g043: Update IRQ numbers for SSI channels
arm64: dts: renesas: r9a07g054: Update IRQ numbers for SSI channels
arm64: dts: renesas: r9a07g044: Update IRQ numbers for SSI channels
arm64: dts: renesas: r8a774c0: Remove bogus voltages from OPP table
arm64: dts: renesas: r8a77990: Remove bogus voltages from OPP table
arm64: dts: renesas: r9a07g054: Add Cortex-A55 PMU node
arm64: dts: renesas: white-hawk-csi-dsi: Add and connect MAX96712
arm64: dts: renesas: r8a779g0: Add and connect all CSI-2, ISP and VIN nodes
arm64: dts: renesas: r8a779f0: Use proper labels for thermal zones
arm64: dts: renesas: r8a779g0: Add thermal nodes
arm64: dts: renesas: rzv2mevk2: Add uart0 pins
arm64: dts: renesas: Drop specifying the GIC_CPU_MASK_SIMPLE() for GICv3 systems
arm64: dts: renesas: r9a07g044: Add Cortex-A55 PMU node
...
Link: https://lore.kernel.org/r/cover.1679907064.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add support for the combination of the NVIDIA Jetson Orin NX (P3767, SKU
0) module and the P3768 carrier board.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds a device tree for the Jetson Orin NX module, which is Jetson
AGX Orin's little sibling with 6 or 8 ARM Cortex-A78AE cores, an Ampere
GPU (1024 GPU and 32 tensor cores) and a number of accelerators for
machine learning, image processing and more.
The Jetson Orin NX comes with either 8 or 16 GiB of 128-bit LPDDR5 and
supports NVME for mass storage.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since IMSSTR register was undocumented on the latest datasheet and
dt-bindings of renesas,ipmmu-vmsa was updated about the
renesas,ipmmu-main property, revise the property on each cache IPMMU
node.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/ed4c21150e42dd23412a8f4af7976f81edc1c9c2.1680592069.git.geert+renesas@glider.be
Specify the bus-type property for all three connected MAX96712.
The default behavior when parsing a node without this property is to
default to D-PHY. Making this explicit plays it safe and future proofs
things as the default parsing comes from the V4L2 core and not the
driver itself.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230331141431.3820311-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Since IMSSTR register was undocumented on the latest datasheet and
dt-bindings of renesas,ipmmu-vmsa was updated about
the renesas,ipmmu-main property, revise the property on each cache
IPMMU node.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20230123013448.1250991-2-yoshihiro.shimoda.uh@renesas.com
[geert: Drop indices from renesas,ipmmu-main properties]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Populate the DynamIQ Shared Unit (DSU) Performance Monitor Unit (PMU)
devices for Tegra234 which has one DSU PMU per CPU cluster.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The serial node does not use clock-names and reset-names:
tegra234-sim-vdk.dtb: serial@3100000: Unevaluated properties are not allowed ('clock-names', 'reset-names' were unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable FHCTL with Spread Spectrum for MAINPLL, MPLL and MSDCPLL
as found on the downstream kernel for this smartphone.
Which one to enable, and at what SSC percentage, was found by
dumping the debugging data from a running downstream kernel and
checking the downstream code.
/proc/freqhopping # cat status
FH status:
===============================================
id == fh_status == pll_status == setting_id == curr_freq == user_defined
0 0 1 0 1599000 0
1 0 1 0 1716000 0
2 1 1 2 1092000 0
3 1 1 2 2912000 0
4 1 0 2 1600000 0
5 0 0 0 0 0
6 0 1 0 1518002 0
7 0 0 0 0 0
8 0 0 0 0 0
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230327083647.22017-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add FHCTL node but keep it disabled as the PLL clocks that should be
handled through FHCTL and the Spread Spectrum Clocking parameters are
board specific.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230327083647.22017-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Configure the hardware PWM for the integrated display's backlight:
all Cherry devices enable the backlight with GPIO82 and manage the
PWM via MediaTek disp-pwm on GPIO97.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230223145426.193590-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the two hardware PWMs for display backlighting but keep them
disabled by default, as usage is board-specific.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20230223145426.193590-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The mt8195 SoC has several hotspots around the CPUs. Specify the
targeted temperature threshold when to apply the mitigation and define
the associated cooling devices.
Signed-off-by: Balsam CHIHI <bchihi@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230209105628.50294-7-bchihi@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add thermal zones and thermal nodes for the mt8195.
Signed-off-by: Balsam CHIHI <bchihi@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230209105628.50294-6-bchihi@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
There is neither a driver that parses this nor a DT binding schema that
documents it, so let's remove from the DTS files that make use of this.
The properties that exist are post-pwm-on-delay-ms and pwm-off-delay-ms,
defined in the pwm-backlight DT binding. If the delays are really needed
then those properties should be used instead.
Brian Norris mentioned though that looking at the first downstream usage
of the pwm-delay-us property for RK3399 Gru systems in ChromiumOS tree,
he couldn't find a spec reference that said that this was really needed.
So perhaps it was unnecessary added and a simple removal would be enough.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20230330231924.2404747-1-javierm@redhat.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This IP is a 10/100 MAC controller compliant with IEEE 802.3 standards.
It supports power management with Energy Efficient Ethernet and Wake-on-LAN
specification. Flow control is provided for half-duplex and full-duplex
mode. For packet transmission and reception, the controller supports
IPv4/UDP/TCP checksum offload and VLAN tag insertion.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230203-evk-board-support-v3-12-0003e80e0095@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In order to use the PMIC, the pwrap support should be added
to allow communication between the SoC and the PMIC.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230203-evk-board-support-v3-6-0003e80e0095@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This new device-tree add the regulators, rtc and keys support
for the MT6357 PMIC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20230203-evk-board-support-v3-5-0003e80e0095@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The reserved size for BL31 is too small.
This has been highlighted by the MPU that now restrict access to BL31
memory to secure world only.
This increase the size of the reserved memory.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230203-evk-board-support-v3-3-0003e80e0095@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable the I2C0 bus provides communication with:
- The integrated RT9466 Switching Battery Charger.
- The integrated MT6691 LP4X buck for VDDQ.
- The integrated MT6691 LP4X buck for VDD2.
- The pin header, to plug external I2C devices.
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221122-mt8365-i2c-support-v6-2-e1009c8afd53@baylibre.com
[mb: move bias-pull-up below pinmux]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
There are four I2C master channels in MT8365 with a same HW architecture.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20221122-mt8365-i2c-support-v6-1-e1009c8afd53@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add the nodes for McASP 0-2.
Use the audio-friendly 96MHz main_1_hsdivout6_clk as clock parent
instead of the default 100Mhz main_2_hsdivout8_clk source.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230313-mcasp_upstream-v10-1-94332149657a@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
J784S4 has 8 MCSPI instances in the main domain and 3 instances
in the MCU domain. Add the DT nodes for all the 11 instances and
keep them disabled. MAIN_MCSPI4 is connected as a slave to MCU_MCSPI2
by default at power-up, MAIN_MCSPI4 and MCU_MCSPI2 are not pinned out
externally.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Link: https://lore.kernel.org/r/20230321082827.14274-5-vaishnav.a@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
J721S2 has 8 MCSPI instances in the main domain and 3 instances
in the MCU domain. Add the DT nodes for all the 11 instances and
keep them disabled. MAIN_MCSPI4 is connected as a slave to MCU_MCSPI2
by default at power-up, MAIN_MCSPI4 and MCU_MCSPI2 are not pinned out
externally.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Link: https://lore.kernel.org/r/20230321082827.14274-4-vaishnav.a@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
