[ Upstream commit 7e406d1ff3 ]
For PREEMPT/DYNAMIC_PREEMPT the *_unlock() will already trigger a
preemption, no point in then calling preempt_schedule_common()
*again*.
Use _cond_resched() instead, since this is a NOP for the preemptible
configs while it provide a preemption point for the others.
Reported-by: xuhaifeng <xuhaifeng@oppo.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/YcGnvDEYBwOiV0cR@hirez.programming.kicks-ass.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c16dc047b ]
Some hypervisors support Arch LBR, but without the LBR XSAVE support.
The current Arch LBR init code prints a warning when the xsave size (0) is
unexpected. Avoid printing the warning for the "no LBR XSAVE" case.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20211215204029.150686-1-ak@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0036fb00a7 ]
The RAPL events exposed under /sys/devices/power/events should only reflect
what the underlying hardware actually support. This is how it works on Intel
RAPL and Intel core/uncore PMUs in general.
But on AMD, this was not the case. All possible RAPL events were advertised.
This is what it showed on an AMD Fam17h:
$ ls /sys/devices/power/events/
energy-cores energy-gpu energy-pkg energy-psys
energy-ram energy-cores.scale energy-gpu.scale energy-pkg.scale
energy-psys.scale energy-ram.scale energy-cores.unit energy-gpu.unit
energy-pkg.unit energy-psys.unit energy-ram.unit
Yet, on AMD Fam17h, only energy-pkg is supported.
This patch fixes the problem. Given the way perf_msr_probe() works, the
amd_rapl_msrs[] table has to have all entries filled out and in particular
the group field, otherwise perf_msr_probe() defaults to making the event
visible.
With the patch applied, the kernel now only shows was is actually supported:
$ ls /sys/devices/power/events/
energy-pkg energy-pkg.scale energy-pkg.unit
The patch also uses the RAPL_MSR_MASK because only the 32-bits LSB of the
RAPL counters are relevant when reading power consumption.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220105185659.643355-1-eranian@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 960dd884dd ]
Instead of only servicing the lowest pending interrupt line, make sure
all pending SoC interrupts are serviced before exiting the chained
handler. This adds a small overhead if only one interrupt is pending,
but should prevent rapid re-triggering of the handler.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/5082ad3cb8b4eedf55075561b93eff6570299fe1.1641739718.git.sander@svanheule.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a48db3fef ]
We need to use test_and_set_bit() when changing xprt state flags to
avoid potentially getting xps->xps_nactive out of sync.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 776d794f28 ]
The refcount leak issues take place in an error handling path. When the
3rd argument buf doesn't match with "offline", "online" or "remove", the
function simply returns -EINVAL and forgets to decrease the reference
count of a rpc_xprt object and a rpc_xprt_switch object increased by
rpc_sysfs_xprt_kobj_get_xprt() and
rpc_sysfs_xprt_kobj_get_xprt_switch(), causing reference count leaks of
both unused objects.
Fix this issue by jumping to the error handling path labelled with
out_put when buf matches none of "offline", "online" or "remove".
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8a09619a5 ]
If the supplied argument doesn't specify the transport type, use the
type of the existing rpc clnt and its existing transport.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8d54baba7 ]
An fs_location attribute returns a string that can be ipv4, ipv6,
or DNS name. An ip location can have a port appended to it and if
no port is present a default port needs to be set. If rpc_pton()
fails to parse, try calling rpc_uaddr2socaddr() that can convert
an universal address.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5b27cc676 ]
Make nfs_parse_server_name available outside of nfs4namespace.c.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1976b2b314 ]
Query the server for other possible trunkable locations for a given
file system on a 4.1+ mount.
v2:
-- added missing static to nfs4_discover_trunking,
reported by the kernel test robot
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a59bb93b7 ]
Define and store if server returns it supports fs_locations attribute
as a capability.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90e12a3191 ]
Remove the check for the zero length fs_locations reply in the
xdr decoding, and instead check for that in the migration code.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b05bf5c63b ]
When decode_devicenotify_args() exits with no entries, we need to
ensure that the struct cb_devicenotifyargs is initialised to
{ 0, NULL } in order to avoid problems in
nfs4_callback_devicenotify().
Reported-by: <rtm@csail.mit.edu>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbd2057e53 ]
kstrdup() returns NULL when some internal memory errors happen, it is
better to check the return value of it so to catch the memory error in
time.
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c52c8376d ]
When the bitmask of the attributes doesn't include the security label,
don't bother printing it. Since the label might not be null terminated,
adjust the printing format accordingly.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5e7b59c34 ]
Currently the nfs_access_get_cached family of functions report a
'struct nfs_access_entry' as the result, with both .mask and .cred set.
However the .cred is never used. This is probably good and there is no
guarantee that it won't be freed before use.
Change to only report the 'mask' - as this is all that is used or needed.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 097f1eefed upstream.
During expression parsing, a new expression field is created which
should inherit the properties of the operands, such as size and
is_signed.
is_signed propagation was missing, causing spurious errors with signed
operands. Add it in parse_expr() and parse_unary() to fix the problem.
Link: https://lkml.kernel.org/r/f4dac08742fd7a0920bf80a73c6c44042f5eaa40.1643319703.git.zanussi@kernel.org
Cc: stable@vger.kernel.org
Fixes: 100719dcef ("tracing: Add simple expression support to hist triggers")
Reported-by: Yordan Karadzhov <ykaradzhov@vmware.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215513
Signed-off-by: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2685c77b80 upstream.
The existing mail mechanism only supports writing of workload types.
However, mailbox command for RFIM (cmd = 0x08) also requires write
operation which is ignored. This results in failing to store RFI
restriction.
Fixint this requires enhancing mailbox writes for non workload
commands too, so remove the check for MBOX_CMD_WORKLOAD_TYPE_WRITE
in mailbox write to allow this other write commands to be supoorted.
At the same time, however, we have to make sure that there is no
impact on read commands, by avoiding to write anything into the
mailbox data register.
To properly implement that, add two separate functions for mbox read
and write commands for the processor thermal workload command type.
This helps to distinguish the read and write workload command types
from each other while sending mbox commands.
Fixes: 5d6fbc96bd ("thermal/drivers/int340x: processor_thermal: Export additional attributes")
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Cc: 5.14+ <stable@vger.kernel.org> # 5.14+
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 994a04a20b upstream.
32-bit processors cannot generally access 64-bit MMIO registers
atomically, and it is unknown in which order the two halves of
this registers would need to be read:
drivers/thermal/intel/int340x_thermal/processor_thermal_mbox.c: In function 'send_mbox_cmd':
drivers/thermal/intel/int340x_thermal/processor_thermal_mbox.c:79:37: error: implicit declaration of function 'readq'; did you mean 'readl'? [-Werror=implicit-function-declaration]
79 | *cmd_resp = readq((void __iomem *) (proc_priv->mmio_base + MBOX_OFFSET_DATA));
| ^~~~~
| readl
The driver already does not build for anything other than x86,
so limit it further to x86-64.
Fixes: aeb58c860d ("thermal/drivers/int340x: processor_thermal: Suppot 64 bit RFIM responses")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aeb58c860d upstream.
Some of the RFIM mail box command returns 64 bit values. So enhance
mailbox interface to return 64 bit values and use them for RFIM
commands.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Fixes: 5d6fbc96bd ("thermal/drivers/int340x: processor_thermal: Export additional attributes")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4fcf1ada4 upstream.
When the driver resumes, the tcc offset is set back to its previous
value. But this only works if the value was user defined as otherwise
the offset isn't saved. This asymmetric logic is harder to maintain and
introduced some issues.
Improve the logic by saving the tcc offset in a suspend op, so the right
value is always restored after a resume.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pI andruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20210909085613.5577-3-atenart@kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0cb4d23ae0 upstream.
Dan Aloni reports:
> Due to commit 8cfb901528 ("NFS: Always provide aligned buffers to
> the RPC read layers") on the client, a read of 0xfff is aligned up
> to server rsize of 0x1000.
>
> As a result, in a test where the server has a file of size
> 0x7fffffffffffffff, and the client tries to read from the offset
> 0x7ffffffffffff000, the read causes loff_t overflow in the server
> and it returns an NFS code of EINVAL to the client. The client as
> a result indefinitely retries the request.
The Linux NFS client does not handle NFS?ERR_INVAL, even though all
NFS specifications permit servers to return that status code for a
READ.
Instead of NFS?ERR_INVAL, have out-of-range READ requests succeed
and return a short result. Set the EOF flag in the result to prevent
the client from retrying the READ request. This behavior appears to
be consistent with Solaris NFS servers.
Note that NFSv3 and NFSv4 use u64 offset values on the wire. These
must be converted to loff_t internally before use -- an implicit
type cast is not adequate for this purpose. Otherwise VFS checks
against sb->s_maxbytes do not work properly.
Reported-by: Dan Aloni <dan.aloni@vastdata.com>
Cc: stable@vger.kernel.org
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a4d333d54 upstream.
NFSv3 and NFSv4 use u64 offset values on the wire. Record these values
verbatim without the implicit type case to loff_t.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6260d9a56a upstream.
Ensure that a client cannot specify a WRITE range that falls in a
byte range outside what the kernel's internal types (such as loff_t,
which is signed) can represent. The kiocb iterators, invoked in
nfsd_vfs_write(), should properly limit write operations to within
the underlying file system's s_maxbytes.
Cc: stable@vger.kernel.org
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6faac3f58 upstream.
iattr::ia_size is a loff_t, which is a signed 64-bit type. NFSv3 and
NFSv4 both define file size as an unsigned 64-bit type. Thus there
is a range of valid file size values an NFS client can send that is
already larger than Linux can handle.
Currently decode_fattr4() dumps a full u64 value into ia_size. If
that value happens to be larger than S64_MAX, then ia_size
underflows. I'm about to fix up the NFSv3 behavior as well, so let's
catch the underflow in the common code path: nfsd_setattr().
Cc: stable@vger.kernel.org
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a648fdeb7c upstream.
iattr::ia_size is a loff_t, so these NFSv3 procedures must be
careful to deal with incoming client size values that are larger
than s64_max without corrupting the value.
Silently capping the value results in storing a different value
than the client passed in which is unexpected behavior, so remove
the min_t() check in decode_sattr3().
Note that RFC 1813 permits only the WRITE procedure to return
NFS3ERR_FBIG. We believe that NFSv3 reference implementations
also return NFS3ERR_FBIG when ia_size is too large.
Cc: stable@vger.kernel.org
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 468d126dab upstream.
For some long forgotten reason, the nfs_client cl_flags field is
initialised in nfs_get_client() instead of being initialised at
allocation time. This quirk was harmless until we moved the call to
nfs_create_rpc_client().
Fixes: dd99e9f98f ("NFSv4: Initialise connection to the server in nfs4_alloc_client()")
Cc: stable@vger.kernel.org # 4.8.x
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aec12836e7 upstream.
When setting up autonegotiation for 88E1118R and compatible PHYs,
a software reset of PHY is issued before setting up polarity.
This is incorrect as changes of MDI Crossover Mode bits are
disruptive to the normal operation and must be followed by a
software reset to take effect. Let's patch m88e1118_config_aneg()
to fix the issue mentioned before by invoking software reset
of the PHY just after setting up MDI-x polarity.
Fixes: 605f196efb ("phy: Add support for Marvell 88E1118 PHY")
Signed-off-by: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Cc: stable@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe4f57bf7b upstream.
It is mandatory for a software to issue a reset upon modifying RGMII
Receive Timing Control and RGMII Transmit Timing Control bit fields of MAC
Specific Control register 2 (page 2, register 21) otherwise the changes
won't be perceived by the PHY (the same is applicable for a lot of other
registers). Not setting the RGMII delays on the platforms that imply it'
being done on the PHY side will consequently cause the traffic loss. We
discovered that the denoted soft-reset is missing in the
m88e1121_config_aneg() method for the case if the RGMII delays are
modified but the MDIx polarity isn't changed or the auto-negotiation is
left enabled, thus causing the traffic loss on our platform with Marvell
Alaska 88E1510 installed. Let's fix that by issuing the soft-reset if the
delays have been actually set in the m88e1121_config_aneg_rgmii_delays()
method.
Cc: stable@vger.kernel.org
Fixes: d6ab933647 ("net: phy: marvell: Avoid unnecessary soft reset")
Signed-off-by: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20220205203932.26899-1-Pavel.Parkhomenko@baikalelectronics.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8375dfac4f upstream.
Commit 43a08c3bda ("can: isotp: isotp_sendmsg(): fix TX buffer concurrent
access in isotp_sendmsg()") introduced a new locking scheme that may render
the userspace application in a locking state when an error is detected.
This issue shows up under high load on simultaneously running isotp channels
with identical configuration which is against the ISO specification and
therefore breaks any reasonable PDU communication anyway.
Fixes: 43a08c3bda ("can: isotp: isotp_sendmsg(): fix TX buffer concurrent access in isotp_sendmsg()")
Link: https://lore.kernel.org/all/20220209073601.25728-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org
Cc: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c759040c1 upstream.
When receiving a CAN frame the current code logic does not consider
concurrently receiving processes which do not show up in real world
usage.
Ziyang Xuan writes:
The following syz problem is one of the scenarios. so->rx.len is
changed by isotp_rcv_ff() during isotp_rcv_cf(), so->rx.len equals
0 before alloc_skb() and equals 4096 after alloc_skb(). That will
trigger skb_over_panic() in skb_put().
=======================================================
CPU: 1 PID: 19 Comm: ksoftirqd/1 Not tainted 5.16.0-rc8-syzkaller #0
RIP: 0010:skb_panic+0x16c/0x16e net/core/skbuff.c:113
Call Trace:
<TASK>
skb_over_panic net/core/skbuff.c:118 [inline]
skb_put.cold+0x24/0x24 net/core/skbuff.c:1990
isotp_rcv_cf net/can/isotp.c:570 [inline]
isotp_rcv+0xa38/0x1e30 net/can/isotp.c:668
deliver net/can/af_can.c:574 [inline]
can_rcv_filter+0x445/0x8d0 net/can/af_can.c:635
can_receive+0x31d/0x580 net/can/af_can.c:665
can_rcv+0x120/0x1c0 net/can/af_can.c:696
__netif_receive_skb_one_core+0x114/0x180 net/core/dev.c:5465
__netif_receive_skb+0x24/0x1b0 net/core/dev.c:5579
Therefore we make sure the state changes and data structures stay
consistent at CAN frame reception time by adding a spin_lock in
isotp_rcv(). This fixes the issue reported by syzkaller but does not
affect real world operation.
Fixes: e057dd3fc2 ("can: add ISO 15765-2:2016 transport protocol")
Link: https://lore.kernel.org/linux-can/d7e69278-d741-c706-65e1-e87623d9a8e8@huawei.com/T/
Link: https://lore.kernel.org/all/20220208200026.13783-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org
Reported-by: syzbot+4c63f36709a642f801c5@syzkaller.appspotmail.com
Reported-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 379f56c24e upstream.
SD card is allowed to signal busy on DAT0 up to 1s after the
CMD49. According to SD spec (version 6.0 section 5.8.1.3) first host
waits until busy of CMD49 is released and only then polls Power
Management Status register up to 1s until the card indicates ready to
power off.
Without waiting for busy before polling status register sometimes card
becomes unresponsive and system fails to suspend:
[ 205.907459] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 206.421274] sunxi-mmc 1c0f000.mmc: data error, sending stop command
[ 206.421321] sunxi-mmc 1c0f000.mmc: send stop command failed
[ 206.421347] mmc0: error -110 reading status reg of PM func
[ 206.421366] PM: dpm_run_callback(): mmc_bus_suspend+0x0/0x74 returns -110
[ 206.421402] mmcblk mmc0:aaaa: PM: failed to suspend async: error -110
[ 206.437064] PM: Some devices failed to suspend, or early wake event detected
Tested with Sandisk Extreme PRO A2 64GB on Allwinner A64 system.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Fixes: 2c5d427690 ("mmc: core: Add support for Power Off Notification for SD cards")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220115121447.641524-1-andrej.skvortzov@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40c67c291a upstream.
Because of the possible failure of the dma_supported(), the
dma_set_mask_and_coherent() may return error num.
Therefore, it should be better to check it and return the error if
fails.
And since the sdhci_setup_host() has already checked the return value of
the enable_dma, we need not check it in sdhci_resume_host() again.
Fixes: 5552d7ad59 ("mmc: sdhci-of-esdhc: set proper dma mask for ls104x chips")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220112083156.1124782-1-jiasheng@iscas.ac.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb8e52e490 upstream.
Commit c2426d2ad5 ("ima: added support for new kernel cmdline parameter
ima_template_fmt") introduced an additional check on the ima_template
variable to avoid multiple template selection.
Unfortunately, ima_template could be also set by the setup function of the
ima_hash= parameter, when it calls ima_template_desc_current(). This causes
attempts to choose a new template with ima_template= or with
ima_template_fmt=, after ima_hash=, to be ignored.
Achieve the goal of the commit mentioned with the new static variable
template_setup_done, so that template selection requests after ima_hash=
are not ignored.
Finally, call ima_init_template_list(), if not already done, to initialize
the list of templates before lookup_template_desc() is called.
Reported-by: Guo Zihua <guozihua@huawei.com>
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Cc: stable@vger.kernel.org
Fixes: c2426d2ad5 ("ima: added support for new kernel cmdline parameter ima_template_fmt")
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7333b9572 upstream.
The removal of ima_dir currently fails since ima_policy still exists, so
remove the ima_policy file before removing the directory.
Fixes: 4af4662fa4 ("integrity: IMA policy")
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 926fd9f23b upstream.
Don't leak a reference to the key if its algorithm is unknown.
Fixes: 947d705972 ("ima: Support EC keys for signature verification")
Cc: <stable@vger.kernel.org> # v5.13+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83230351c5 upstream.
audit_log_start() returns audit_buffer pointer on success or NULL on
error, so it is better to check the return value of it.
Fixes: 3323eec921 ("integrity: IMA as an integrity service provider")
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9aa422ad32 upstream.
The function tipc_mon_rcv() allows a node to receive and process
domain_record structs from peer nodes to track their views of the
network topology.
This patch verifies that the number of members in a received domain
record does not exceed the limit defined by MAX_MON_DOMAIN, something
that may otherwise lead to a stack overflow.
tipc_mon_rcv() is called from the function tipc_link_proto_rcv(), where
we are reading a 32 bit message data length field into a uint16. To
avert any risk of bit overflow, we add an extra sanity check for this in
that function. We cannot see that happen with the current code, but
future designers being unaware of this risk, may introduce it by
allowing delivery of very large (> 64k) sk buffers from the bearer
layer. This potential problem was identified by Eric Dumazet.
This fixes CVE-2022-0435
Reported-by: Samuel Page <samuel.page@appgate.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Fixes: 35c55c9877 ("tipc: add neighbor monitoring framework")
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Samuel Page <samuel.page@appgate.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6ce9c5831 upstream.
The soft dependency on cryptomgr is only needed in algapi because
if algapi isn't present then no algorithms can be loaded. This
also fixes the case where api is built-in but algapi is built as
a module as the soft dependency would otherwise get lost.
Fixes: 8ab23d547f ("crypto: api - Add softdep on cryptomgr")
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ca8581e79 upstream.
cifs client set 4 to DataLength of create_posix context, which mean
Mode variable of create_posix context is only available. So buffer
validation of ksmbd should check only the size of Mode except for
the size of Reserved variable.
Fixes: 8f77150c15 ("ksmbd: add buffer validation for SMB2_CREATE_CONTEXT")
Cc: stable@vger.kernel.org # v5.15+
Reported-by: Steve French <smfrench@gmail.com>
Tested-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c212e1bae upstream.
Refuse SIDA memops on guests which are not protected.
For normal guests, the secure instruction data address designation,
which determines the location we access, is not under control of KVM.
Fixes: 19e1227768 (KVM: S390: protvirt: Introduce instruction data area bounce buffer)
Signed-off-by: Janis Schoetterl-Glausch <scgl@linux.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd2db32e7c upstream.
It was reported that the mmc host structure could be accessed after it
was freed in moxart_remove(), so fix this by saving the base register of
the device and using it instead of the pointer dereference.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Cc: Xin Xiong <xiongx18@fudan.edu.cn>
Cc: Xin Tan <tanxin.ctf@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Yang Li <yang.lee@linux.alibaba.com>
Cc: linux-mmc@vger.kernel.org
Cc: stable <stable@vger.kernel.org>
Reported-by: whitehat002 <hackyzh002@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220127071638.4057899-1-gregkh@linuxfoundation.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aad51ca71a upstream.
Add a test that sends large udp packet (which is fragmented)
via a stateless nft nat rule, i.e. 'ip saddr set 10.2.3.4'
and check that the datagram is received by peer.
On kernels without
commit 4e1860a386 ("netfilter: nft_payload: do not update layer 4 checksum when mangling fragments")',
this will fail with:
cmp: EOF on /tmp/tmp.V1q0iXJyQF which is empty
-rw------- 1 root root 4096 Jan 24 22:03 /tmp/tmp.Aaqnq4rBKS
-rw------- 1 root root 0 Jan 24 22:03 /tmp/tmp.V1q0iXJyQF
ERROR: in and output file mismatch when checking udp with stateless nat
FAIL: nftables v1.0.0 (Fearless Fosdick #2)
On patched kernels, this will show:
PASS: IP statless for ns2-PFp89amx
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eda0cf1202 upstream.
Add a specific test for the reload issue fixed with
commit 23c54263ef ("netfilter: nft_set_pipapo: allocate pcpu scratch maps on clone").
Add to set, then flush set content + restore without other add/remove in
the transaction.
On kernels before the fix, this test case fails:
net,mac with reload [FAIL]
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f51ce0b9e upstream.
The return from the call to platform_get_irq() is int, it can be
a negative error code, however this is being assigned to an unsigned
int variable 'irqn', so making 'irqn' an int.
Eliminate the following coccicheck warning:
./drivers/gpio/gpio-mpc8xxx.c:391:5-21: WARNING: Unsigned expression
compared with zero: mpc8xxx_gc -> irqn < 0
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: 0b39536cc6 ("gpio: mpc8xxx: Fix IRQ check in mpc8xxx_probe")
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c1cf55577 upstream.
The return from the call to platform_get_irq() is int, it can be
a negative error code, however this is being assigned to an unsigned
int variable 'parent_irq', so making 'parent_irq' an int.
Eliminate the following coccicheck warning:
./drivers/gpio/gpio-idt3243x.c:167:6-16: WARNING: Unsigned expression
compared with zero: parent_irq < 0
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: 30fee1d746 ("gpio: idt3243x: Fix IRQ check in idt_gpio_probe")
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
