Firmware has added assert if beacon template is received after
vdev_down. Firmware expects beacon template after vdev_start
and before vdev_up. This change is needed to support MBSSID EMA
cases in firmware.
Hence, Change the sequence in ath11k as expected from firmware.
This new change is not causing any issues with older
firmware.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1.r3-00011-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1.r4-00008-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
[sven@narfation.org: added tested-on/fixes information]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210525133028.2805615-1-sven@narfation.org
Functions 'ath10k_pci_free_pipes' and 'ath10k_wmi_alloc_skb'
are declared twice in their header file, so remove the repeated
declaration.
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1622448459-50805-1-git-send-email-zhangshaokun@hisilicon.com
When the code execute this if statement, the value of ret is 0.
However, we can see from the ath10k_warn() log that the value of
ret should be -EINVAL.
Clean up smatch warning:
drivers/net/wireless/ath/ath10k/mac.c:5596 ath10k_add_interface() warn:
missing error code 'ret'
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: ccec9038c7 ("ath10k: enable raw encap mode and software crypto engine")
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1621939577-62218-1-git-send-email-yang.lee@linux.alibaba.com
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/wil6210/interrupt.c:28: warning: expecting prototype for Theory of operation(). Prototype was for WIL6210_IRQ_DISABLE() instead
drivers/net/wireless/ath/wil6210/wmi.c:227: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/net/wireless/ath/wil6210/wmi.c:245: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
drivers/net/wireless/ath/wil6210/wmi.c:263: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
Cc: Maya Erez <merez@codeaurora.org>
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210517050141.61488-4-shenyang39@huawei.com
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/hw.c:119: warning: expecting prototype for ath_hw_set_bssid_mask(). Prototype was for ath_hw_setbssidmask() instead
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210517050141.61488-3-shenyang39@huawei.com
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/ath/ath5k/pcu.c:865: warning: expecting prototype for at5k_hw_stop_rx_pcu(). Prototype was for ath5k_hw_stop_rx_pcu() instead
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210517050141.61488-2-shenyang39@huawei.com
Right now wcn->hal_buf is allocated in wcn36xx_start(). This is a problem
since we should have setup all of the buffers we required by the time
ieee80211_register_hw() is called.
struct ieee80211_ops callbacks may run prior to mac_start() and therefore
wcn->hal_buf must be initialized.
This is easily remediated by moving the allocation to probe() taking the
opportunity to tidy up freeing memory by using devm_kmalloc().
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605173347.2266003-1-bryan.odonoghue@linaro.org
Enable flags for
- Magic packet
- GTK rekey
Previous patches implemented the necessary code to switch these two on.
Standalone magic packet absent GTK rekey is pretty useless, so it makes
sense to flag both at once.
Once done it is possible for wcn36xx firmware to
1. Respond to ipv4 and ipv6 ARP/NS lookup requests
2. Bring the system out of suspend when a magic packet is received.
Magic in our case is a simple ipv4 or ipv6 unicast.
3. GTK rekey whilst in suspend
Once we wake from suspend the GTK will be updated as necessary
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-13-bryan.odonoghue@linaro.org
This commit is the corresponding resume() path request to the firmware when
resuming. Unlike the suspend() version which is a unidirectional
indication, the resume version is a standard request/response.
Once the resume() request completes ipv4 ARP, ipv6 NS and GTK rekey offload
stop working and can subsequently be rolled back.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-12-bryan.odonoghue@linaro.org
In order to activate ipv4 ARP offload, ipv6 NS offload and firmware GTK
offload we need to send a unidirectional indication from host to wcn
indicating a transition to suspend.
Once done, firmware will respond to ARP broadcasts, ipv6 NS lookups and
perform GTK rekeys without waking the host.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-11-bryan.odonoghue@linaro.org
Having enabled GTK rekey in suspend, we need to extract the replay counter
from the firmware on resume and perform a ieee80211_gtk_rekey_notify() so
that the STA remains verified from the perspective of the AP.
In order to enable the SMD command and response we need to pack the
existing command/response structures. Given these structures are currently
unused, there's no need to backport this as a fix.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-10-bryan.odonoghue@linaro.org
Using previously set GTK KCK and KEK material this commit adds GTK rekeying
to the WoWLAN suspend/resume path. A small error in the packing of the
up to now unused command structure is fixed as we go.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-9-bryan.odonoghue@linaro.org
Add a callback for Group Temporal Key tracking as provided by the standard
WiFi ops structure.
We track the key to integrate GTK offloading into the WoWLAN suspend path
later on. Code comes from the Intel iwlwifi driver with minimal name
changes.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-8-bryan.odonoghue@linaro.org
We need to respond to ipv6 namespace lookups when in suspend. This patch
adds the necessary changes to issue the appropriate firmware command on
suspend and resume to enter/exit firmware offloaded ns lookup.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-7-bryan.odonoghue@linaro.org
Taking code from iwlwifi this commit adds a standard callback for
ipv6_addr_change().
This callback allows wcn36xx to know the set of ipv6 addresses. Something
we need to know in order to get wowlan working with ipv6.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-6-bryan.odonoghue@linaro.org
Testing on Android reveals that the flush on both suspend and resume of the
firmware indication work-queue can stall indefinitely.
Given this code path doesn't appear to have been exercised up until now,
removing this flush to unblock this situation.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-5-bryan.odonoghue@linaro.org
Add ARP offload support. Firmware is capable of responding to ARP requests
for a single ipv4 address only.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-4-bryan.odonoghue@linaro.org
A subsequent set of patches will extend out suspend/resume support in this
driver, we cannot set the firmware up for multiple ipv4/ipv6 addresses and
as such we can't iterate through a list of ieee80211_vif.
Constrain the interaction with the firmware to the first ieee80211_vif on
the suspend/resume/wowlan path.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-3-bryan.odonoghue@linaro.org
wcn36xx_smd_set_power_params() can return an error. For the purposes of
entering into suspend we need the suspend() function to trap and report
errors up the stack.
First step in this process is reporting the existing result code for
wcn36xx_smd_set_power_params().
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210605011140.2004643-2-bryan.odonoghue@linaro.org
Fix the following W=1 build warning:
drivers/net/wireless/ath/ath10k/htt_rx.c:1790:7: warning: variable ‘more_frags’ set but not used [-Wunused-but-set-variable]
1790 | bool more_frags;
| ^~~~~~~~~~
Fixes: a1166b2653 ("ath10k: add CCMP PN replay protection for fragmented frames for PCIe")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210526142219.2542528-1-yangyingliang@huawei.com
kernel test robot reports over 200 build errors and warnings
that are due to this Kconfig problem when CARL9170=m,
MAC80211=y, and LEDS_CLASS=m.
WARNING: unmet direct dependencies detected for MAC80211_LEDS
Depends on [n]: NET [=y] && WIRELESS [=y] && MAC80211 [=y] && (LEDS_CLASS [=m]=y || LEDS_CLASS [=m]=MAC80211 [=y])
Selected by [m]:
- CARL9170_LEDS [=y] && NETDEVICES [=y] && WLAN [=y] && WLAN_VENDOR_ATH [=y] && CARL9170 [=m]
CARL9170_LEDS selects MAC80211_LEDS even though its kconfig
dependencies are not met. This happens because 'select' does not follow
any Kconfig dependency chains.
Fix this by making CARL9170_LEDS depend on MAC80211_LEDS, where
the latter supplies any needed dependencies on LEDS_CLASS.
Fixes: 1d7e1e6b1b ("carl9170: Makefile, Kconfig files and MAINTAINERS")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: linux-wireless@vger.kernel.org
Cc: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Christian Lamparter <chunkeey@googlemail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210530031134.23274-1-rdunlap@infradead.org
When chip_id is not supported, the resources will be freed
on path err_unsupported, these resources will also be freed
when calling ath10k_pci_remove(), it will cause double free,
so return -ENODEV when it doesn't support the device with wrong
chip_id.
Fixes: c0c378f990 ("ath10k: remove target soc ps code")
Fixes: 7505f7c3ec ("ath10k: create a chip revision whitelist")
Fixes: f8914a1462 ("ath10k: restore QCA9880-AR1A (v1) detection")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210522105822.1091848-3-yangyingliang@huawei.com
When chip id is not supported, it go to path err_unsupported
to print the error message.
Fixes: f8914a1462 ("ath10k: restore QCA9880-AR1A (v1) detection")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210522105822.1091848-2-yangyingliang@huawei.com
For QCA6390, one PCI related clock drifts sometimes, and it makes
PCI link difficult to quit L1ss. Current implementation fixed this
by configuring some related regs using ath11k_pci_fix_l1ss.
WCN6855 does not have this clock drift problem, so no need to set
these regs.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-8-jouni@codeaurora.org
This patch is to add support for WCN6855. For station mode,
WCN6855 is able to connect to an AP, and ping works well.
For AP mode, hostapd is able to bringup an SAP interface with
WCN6855, a normal station can connect to this AP and
ping works well.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-7-jouni@codeaurora.org
For WCN6855, the layout of hal rx mpdu info is different, so need to
handle this target differently when getting peer id.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-6-jouni@codeaurora.org
For WCN6855, WBM idle link ring needs a reinit.
Without this reinit, firmware crash might happen occasionally.
This is requested by the hw team.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-5-jouni@codeaurora.org
WCN6855 needs a different reo configuration, so add separate handling
for this target in ath11k_hw_ops.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-4-jouni@codeaurora.org
hal rx descriptor is different for WCN6855 and there are such a lot
of handlers processing this descriptor in data path. So add separate
handling for this target.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-3-jouni@codeaurora.org
Reg address of WCN6855 is different from other devices,
so add separate reg definition for this target.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-2-jouni@codeaurora.org
I got this crash more times during debugging of PCIe controller and crash
happens somehow at the time when PCIe kernel code started link retraining (as
part of ASPM code) when at the same time PCIe link went down and ath9k probably
executed hw reset procedure.
Currently I'm not able to reproduce this issue as it looks like to be
some race condition between link training, ASPM, link down and reset
path. And as always, race conditions which depends on more input
parameters are hard to reproduce as it depends on precise timings.
But it is clear that pointers are zero in this case and should be
properly filled as same code pattern is used in ath9k_stop() function.
Anyway I was able to reproduce this crash by manually triggering ath
reset worker prior putting card up. I created simple patch to export
reset functionality via debugfs and use it to "simulate" of triggering
reset. s proved that NULL-pointer dereference issue is there.
Function ath9k_hw_reset() is dereferencing chan structure pointer, so it
needs to be non-NULL pointer.
Function ath9k_stop() already contains code which sets ah->curchan to valid
non-NULL pointer prior calling ath9k_hw_reset() function.
Add same code pattern also into ath_reset_internal() function to prevent
kernel NULL pointer dereference in ath9k_hw_reset() function.
This change fixes kernel NULL pointer dereference in ath9k_hw_reset() which
is caused by calling ath9k_hw_reset() from ath_reset_internal() with NULL
chan structure.
[ 45.334305] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008
[ 45.344417] Mem abort info:
[ 45.347301] ESR = 0x96000005
[ 45.350448] EC = 0x25: DABT (current EL), IL = 32 bits
[ 45.356166] SET = 0, FnV = 0
[ 45.359350] EA = 0, S1PTW = 0
[ 45.362596] Data abort info:
[ 45.365756] ISV = 0, ISS = 0x00000005
[ 45.369735] CM = 0, WnR = 0
[ 45.372814] user pgtable: 4k pages, 39-bit VAs, pgdp=000000000685d000
[ 45.379663] [0000000000000008] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000
[ 45.388856] Internal error: Oops: 96000005 [#1] SMP
[ 45.393897] Modules linked in: ath9k ath9k_common ath9k_hw
[ 45.399574] CPU: 1 PID: 309 Comm: kworker/u4:2 Not tainted 5.12.0-rc2-dirty #785
[ 45.414746] Workqueue: phy0 ath_reset_work [ath9k]
[ 45.419713] pstate: 40000005 (nZcv daif -PAN -UAO -TCO BTYPE=--)
[ 45.425910] pc : ath9k_hw_reset+0xc4/0x1c48 [ath9k_hw]
[ 45.431234] lr : ath9k_hw_reset+0xc0/0x1c48 [ath9k_hw]
[ 45.436548] sp : ffffffc0118dbca0
[ 45.439961] x29: ffffffc0118dbca0 x28: 0000000000000000
[ 45.445442] x27: ffffff800dee4080 x26: 0000000000000000
[ 45.450923] x25: ffffff800df9b9d8 x24: 0000000000000000
[ 45.456404] x23: ffffffc0115f6000 x22: ffffffc008d0d408
[ 45.461885] x21: ffffff800dee5080 x20: ffffff800df9b9d8
[ 45.467366] x19: 0000000000000000 x18: 0000000000000000
[ 45.472846] x17: 0000000000000000 x16: 0000000000000000
[ 45.478326] x15: 0000000000000010 x14: ffffffffffffffff
[ 45.483807] x13: ffffffc0918db94f x12: ffffffc011498720
[ 45.489289] x11: 0000000000000003 x10: ffffffc0114806e0
[ 45.494770] x9 : ffffffc01014b2ec x8 : 0000000000017fe8
[ 45.500251] x7 : c0000000ffffefff x6 : 0000000000000001
[ 45.505733] x5 : 0000000000000000 x4 : 0000000000000000
[ 45.511213] x3 : 0000000000000000 x2 : ffffff801fece870
[ 45.516693] x1 : ffffffc00eded000 x0 : 000000000000003f
[ 45.522174] Call trace:
[ 45.524695] ath9k_hw_reset+0xc4/0x1c48 [ath9k_hw]
[ 45.529653] ath_reset_internal+0x1a8/0x2b8 [ath9k]
[ 45.534696] ath_reset_work+0x2c/0x40 [ath9k]
[ 45.539198] process_one_work+0x210/0x480
[ 45.543339] worker_thread+0x5c/0x510
[ 45.547115] kthread+0x12c/0x130
[ 45.550445] ret_from_fork+0x10/0x1c
[ 45.554138] Code: 910922c2 9117e021 95ff0398 b4000294 (b9400a61)
[ 45.560430] ---[ end trace 566410ba90b50e8b ]---
[ 45.565193] Kernel panic - not syncing: Oops: Fatal exception in interrupt
[ 45.572282] SMP: stopping secondary CPUs
[ 45.576331] Kernel Offset: disabled
[ 45.579924] CPU features: 0x00040002,0000200c
[ 45.584416] Memory Limit: none
[ 45.587564] Rebooting in 3 seconds..
Signed-off-by: Pali Rohár <pali@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210402122653.24014-1-pali@kernel.org
can and wireless trees. Notably including fixes for the recently
announced "FragAttacks" WiFi vulnerabilities. Rather large batch,
touching some core parts of the stack, too, but nothing hair-raising.
Current release - regressions:
- tipc: make node link identity publish thread safe
- dsa: felix: re-enable TAS guard band mode
- stmmac: correct clocks enabled in stmmac_vlan_rx_kill_vid()
- stmmac: fix system hang if change mac address after interface ifdown
Current release - new code bugs:
- mptcp: avoid OOB access in setsockopt()
- bpf: Fix nested bpf_bprintf_prepare with more per-cpu buffers
- ethtool: stats: fix a copy-paste error - init correct array size
Previous releases - regressions:
- sched: fix packet stuck problem for lockless qdisc
- net: really orphan skbs tied to closing sk
- mlx4: fix EEPROM dump support
- bpf: fix alu32 const subreg bound tracking on bitwise operations
- bpf: fix mask direction swap upon off reg sign change
- bpf, offload: reorder offload callback 'prepare' in verifier
- stmmac: Fix MAC WoL not working if PHY does not support WoL
- packetmmap: fix only tx timestamp on request
- tipc: skb_linearize the head skb when reassembling msgs
Previous releases - always broken:
- mac80211: address recent "FragAttacks" vulnerabilities
- mac80211: do not accept/forward invalid EAPOL frames
- mptcp: avoid potential error message floods
- bpf, ringbuf: deny reserve of buffers larger than ringbuf to prevent
out of buffer writes
- bpf: forbid trampoline attach for functions with variable arguments
- bpf: add deny list of functions to prevent inf recursion of tracing
programs
- tls splice: check SPLICE_F_NONBLOCK instead of MSG_DONTWAIT
- can: isotp: prevent race between isotp_bind() and isotp_setsockopt()
- netfilter: nft_set_pipapo_avx2: Add irq_fpu_usable() check,
fallback to non-AVX2 version
Misc:
- bpf: add kconfig knob for disabling unpriv bpf by default
-----BEGIN PGP SIGNATURE-----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=peMK
-----END PGP SIGNATURE-----
Merge tag 'net-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.13-rc4, including fixes from bpf, netfilter,
can and wireless trees. Notably including fixes for the recently
announced "FragAttacks" WiFi vulnerabilities. Rather large batch,
touching some core parts of the stack, too, but nothing hair-raising.
Current release - regressions:
- tipc: make node link identity publish thread safe
- dsa: felix: re-enable TAS guard band mode
- stmmac: correct clocks enabled in stmmac_vlan_rx_kill_vid()
- stmmac: fix system hang if change mac address after interface
ifdown
Current release - new code bugs:
- mptcp: avoid OOB access in setsockopt()
- bpf: Fix nested bpf_bprintf_prepare with more per-cpu buffers
- ethtool: stats: fix a copy-paste error - init correct array size
Previous releases - regressions:
- sched: fix packet stuck problem for lockless qdisc
- net: really orphan skbs tied to closing sk
- mlx4: fix EEPROM dump support
- bpf: fix alu32 const subreg bound tracking on bitwise operations
- bpf: fix mask direction swap upon off reg sign change
- bpf, offload: reorder offload callback 'prepare' in verifier
- stmmac: Fix MAC WoL not working if PHY does not support WoL
- packetmmap: fix only tx timestamp on request
- tipc: skb_linearize the head skb when reassembling msgs
Previous releases - always broken:
- mac80211: address recent "FragAttacks" vulnerabilities
- mac80211: do not accept/forward invalid EAPOL frames
- mptcp: avoid potential error message floods
- bpf, ringbuf: deny reserve of buffers larger than ringbuf to
prevent out of buffer writes
- bpf: forbid trampoline attach for functions with variable arguments
- bpf: add deny list of functions to prevent inf recursion of tracing
programs
- tls splice: check SPLICE_F_NONBLOCK instead of MSG_DONTWAIT
- can: isotp: prevent race between isotp_bind() and
isotp_setsockopt()
- netfilter: nft_set_pipapo_avx2: Add irq_fpu_usable() check,
fallback to non-AVX2 version
Misc:
- bpf: add kconfig knob for disabling unpriv bpf by default"
* tag 'net-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (172 commits)
net: phy: Document phydev::dev_flags bits allocation
mptcp: validate 'id' when stopping the ADD_ADDR retransmit timer
mptcp: avoid error message on infinite mapping
mptcp: drop unconditional pr_warn on bad opt
mptcp: avoid OOB access in setsockopt()
nfp: update maintainer and mailing list addresses
net: mvpp2: add buffer header handling in RX
bnx2x: Fix missing error code in bnx2x_iov_init_one()
net: zero-initialize tc skb extension on allocation
net: hns: Fix kernel-doc
sctp: fix the proc_handler for sysctl encap_port
sctp: add the missing setting for asoc encap_port
bpf, selftests: Adjust few selftest result_unpriv outcomes
bpf: No need to simulate speculative domain for immediates
bpf: Fix mask direction swap upon off reg sign change
bpf: Wrap aux data inside bpf_sanitize_info container
bpf: Fix BPF_LSM kconfig symbol dependency
selftests/bpf: Add test for l3 use of bpf_redirect_peer
bpftool: Add sock_release help info for cgroup attach/prog load command
net: dsa: microchip: enable phy errata workaround on 9567
...
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2021-05-26
Jesse Brandeburg says:
In this series I address the C=2 (sparse) warnings. The goal is to be
completely sparse clean in the drivers/net/ethernet/intel directory.
This can help us run this tool for every patch, and helps the kernel
code by reducing technical debt.
NOTE: there is one warning left in ixgbe XDP code using rcu_assign_pointer().
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ixgbe: reduce checker warnings
ixgbe: use checker safe conversions
igbvf: convert to strongly typed descriptors
intel: call csum functions with well formatted arguments
igb: override two checker warnings
igb: fix assignment on big endian machines
igb: handle vlan types with checker enabled
igb/igc: use strongly typed pointer
fm10k: move error check
intel: remove checker warning
e100: handle eeprom as little endian
====================
Link: https://lore.kernel.org/r/20210526172346.3515587-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Document the phydev::dev_flags bit allocation to allow bits 15:0 to
define PHY driver specific behavior, bits 23:16 to be reserved for now,
and bits 31:24 to hold generic PHY driver flags.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20210526184617.3105012-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some labels are only used once, so we delete them and use the
return statement instead of the goto statement.
Signed-off-by: wengjianfeng <wengjianfeng@yulong.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210526011624.11204-1-samirweng1979@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In function st95hf_in_send_cmd, the variable rc is assigned then goto
error label, which just returns rc, so we use return to replace it.
Since error label only used once in the function, so we remove error label.
Signed-off-by: wengjianfeng <wengjianfeng@yulong.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210526005651.12652-1-samirweng1979@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the sparse warnings in the ixgbe crypto offload code. These
changes were made in the most conservative way (force cast)
in order to hopefully not break the code. I suspect that the
code might still be broken on big-endian architectures, but
no one is complaining, so I'm just leaving it functionally
the same.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Shannon Nelson <snelson@pensando.io>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ixgbe hardware needs some very specific programming for
certain registers, which led to some misguided usage of ntohs
instead of using be16_to_cpu(), as well as a home grown swap
followed by an ntohs. Sparse didn't like this at all, and this
fixes the C=2 build, with code that uses native kernel interface.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The igbvf driver for some reason never strongly typed it's descriptor
formats. Make this driver like the rest of the Intel drivers and use
__le* for our little endian descriptors.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The sparse build (C=2) found that there were two drivers
who had not been convered to call the csum_replace_by_diff() function
with sparse clean arguments. Most if not all drivers force the cast
like this patch does. So these drivers are now joining the party
(a bit late), but with no functional change.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The igb PTP code was using htons() on a constant to try to
byte swap the value before writing it to a register. This byte
swap has the consequence of triggering sparse conflicts between
the register write which expect cpu ordered input, and the code
which generated a big endian constant. Just override the cast
to make sure code doesn't change but silence the warning.
Can't do a __swab16 in this case because big endian systems
would then write the wrong value.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
