The shutdown GPIO is active low (SD_N), but this depends on actual board
layout. Linux drivers should only care about logical state, where high
(1) means shutdown and low (0) means do not shutdown.
Invert the GPIO to match logical value while preserving backwards DTB
compatibility. It is not possible to detect whether ACTIVE_HIGH flag in
DTB is because it is an old DTB (using incorrect flag) or it is a new
DTB with a correct hardware pin polarity description. Therefore the
solution prioritizes backwards compatibility while relying on relevant
DTS being upstreamed.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230102114152.297305-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This helps figuring out why the device probe is deferred, e.g. missing
FSL_EDMA driver.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20230111161144.3275546-1-alexander.stein@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Initialize is_dsp_mode flag in the beginning of function
fsl_sai_set_dai_fmt_tr().
When the DAIFMT is DAIFMT_DSP_B the first time, is_dsp_mode is
true, then the second time DAIFMT is DAIFMT_I2S, is_dsp_mode
still true, which is a wrong state. So need to initialize
is_dsp_mode flag every time.
Fixes: a3f7dcc9cc ("ASoC: fsl-sai: Add SND_SOC_DAIFMT_DSP_A/B support.")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Link: https://lore.kernel.org/r/1673852874-32200-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>:
First patch fixes problems reported when performing shutdown. Second one
is for a problem reported by LKP. Last one fixes problem reported by
checkpatch.
Utilize the helper function instead of casting from ->private_data
or snd_pcm_substream_chip() directly.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230113191410.1454566-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Checkpatch script recommends using min_t instead of min with the cast.
Fixes: 69b23b3937 ("ASoC: Intel: avs: Event tracing")
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20230113190310.1451693-4-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When building a PXA kernel without legacy board file support,
the AC97 code is not built, so none of the AC97 drivers
can be used.
Add a Kconfig prompt to let users turn it on, and have it
enabled by default.
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230105134622.254560-15-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactor i2s clock values based on hw_params and use srate and
bclk_ratio variables in clock enable API instead hard-code values.
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://lore.kernel.org/r/20230109132104.1259479-4-venkataprasad.potturu@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
when using same cpu dai for 2 different dai links
below error is reported.
error: can't find BE for DAI ACPHS_VIRTUAL1.OUT
To avoid this error add new cpu dai.
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://lore.kernel.org/r/20230109132104.1259479-2-venkataprasad.potturu@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Tinghan Shen <tinghan.shen@mediatek.com>:
Add support of MediaTek mt8188 SoC DSP to SOF.
The sof driver patches in this series are taken from
thesofproject/linux/tree/topic/sof-dev-rebase.
The chances are that any error we see here will be EPROBE_DEFER but let's
actually tell the user so they know.
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230106-asoc-fsl-err-log-v1-1-49d845c99434@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the generic iomem callback for debugfs_add_region_item to support
sof-logger.
Signed-off-by: Tinghan Shen <tinghan.shen@mediatek.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230110084312.12953-4-tinghan.shen@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support of SOF on MediaTek MT8188 SoC.
MT8188 ADSP integrates with a single core Cadence HiFi-5 DSP.
The IPC communication between AP and DSP is based on shared DRAM and
mailbox interrupt.
The change in the mt8186.h is compatible on both mt8186 and
mt8188. The register controls booting the DSP core with the
default address or the user specified address. Both mt8186
and mt8188 should boot with the user specified boot in the driver.
The usage of the register is the same on both SoC, but the
control bit is different on mt8186 and mt8188, which is bit 1 on mt8186
and bit 0 on mt8188. Configure the redundant bit has noside effect
on both SoCs.
Signed-off-by: Tinghan Shen <tinghan.shen@mediatek.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230110084312.12953-3-tinghan.shen@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Francesco Dolcini <francesco@dolcini.it>:
Add support for BTL (Bridge Tied Load) configuration to NAU8822 audio codec,
since this requires adding a new property to the binding convert it from
txt to yaml first.
Merge series from Chancel Liu <chancel.liu@nxp.com>:
This patchset supports XCVR on i.MX93 platform.
changes in v2:
- remove unnecessary code which causes kernel test robot reporting error
Chancel Liu (3):
ASoC: dt-bindings: fsl,xcvr: Add compatible string for i.MX93 platform
ASoC: fsl_xcvr: Add support for i.MX93 platform
ASoC: fsl_xcvr: Add constraints of period size while using eDMA
.../devicetree/bindings/sound/fsl,xcvr.yaml | 1 +
sound/soc/fsl/fsl_xcvr.c | 155 ++++++++++++------
sound/soc/fsl/fsl_xcvr.h | 7 +
3 files changed, 115 insertions(+), 48 deletions(-)
--
2.25.1
commit dcc2c012c7 ("ASoC: Fix gpiolib dependencies") removed a
series of unnecessary dependencies on GPIOLIB when the gpio was
optional.
A similar simplification seems valid for nau8315, so remove the
dependency as well. This will avoid the following warning
WARNING: unmet direct dependencies detected for SND_SOC_NAU8315
Depends on [n]: SOUND [=y] && !UML && SND [=y] && SND_SOC [=y] &&
GPIOLIB [=n]
Selected by [y]:
- SND_SOC_INTEL_SOF_NAU8825_MACH [=y] && SOUND [=y] && !UML &&
SND [=y] && SND_SOC [=y] && SND_SOC_INTEL_MACH [=y] &&
(SND_SOC_SOF_HDA_LINK [=y] || SND_SOC_SOF_BAYTRAIL [=n]) &&
I2C [=y] && ACPI [=y] && SND_HDA_CODEC_HDMI [=y] &&
SND_SOC_SOF_HDA_AUDIO_CODEC [=y] && (MFD_INTEL_LPSS [=n] ||
COMPILE_TEST [=y])
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ajye Huang <ajye_huang@compal.corp-partner.google.com>
Link: https://lore.kernel.org/r/20230108114351.539786-1-ajye_huang@compal.corp-partner.google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function primary_codec_init() should return 0 if dmic_sel is null.
Here is the warning message reported by 0-DAY CI Kernel Test Service.
smatch warnings:
primary_codec_init() warn: missing error code? 'ret'
...
2022-11-02 141 if (!priv->dmic_sel) {
2022-11-02 142 dev_info(card->dev, "dmic_sel is null\n");
2022-11-02 @143 return ret;
return -EIVNAL;? return 0;?
2022-11-02 144 }
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Ajye Huang <ajye_huang@compal.corp-partner.google.com>
Link: https://lore.kernel.org/r/20230107175933.12973-1-ajye_huang@compal.corp-partner.google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Clang warns:
sound/soc/amd/ps/pci-ps.c:218:2: error: variable 'ret' is used uninitialized whenever switch default is taken [-Werror,-Wsometimes-uninitialized]
default:
^~~~~~~
sound/soc/amd/ps/pci-ps.c:239:9: note: uninitialized use occurs here
return ret;
^~~
sound/soc/amd/ps/pci-ps.c:190:9: note: initialize the variable 'ret' to silence this warning
int ret;
^
= 0
1 error generated.
ret is used uninitialized if 'goto de_init' is taken. As this is not an
error nor should the ACP be deinitialized, just directly return 0 in
this case statement, which resolves the warning.
Fixes: 1d325cdaf7 ("ASoC: amd: ps: refactor platform device creation logic")
Link: https://github.com/ClangBuiltLinux/linux/issues/1779
Suggested-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Syed Saba Kareem <syed.sabakareem@amd.com>
Link: https://lore.kernel.org/r/20230105-wsometimes-uninitialized-pci-ps-c-v2-1-c50321676325@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
eDMA on i.MX93 platform requires the period size to be multiple of
maxburst.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20230104023953.2973362-4-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add compatible string and specific soc data to support XCVR on i.MX93
platform. XCVR IP on i.MX93 is cut to SPDIF only by removing external
PHY.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20230104023953.2973362-3-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow configuring the two loudspeaker outputs as a
single Bridge Tied Load output getting higher output power.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20230104140412.35575-4-francesco@dolcini.it
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse warning:
error: symbol 'acp63_fill_platform_dev_info' was not declared. Should
it be static?
Also reduce line lines below 100 characters.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230104145708.25051-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Retrieve acp_lock mutex as platform data and use it for protecting
ACP common registers access in acp pdm driver.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230104055435.321327-2-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of calling put_device(&adev->dev) where adev is a pointer
to an ACPI device, use specific call, i.e. acpi_dev_put().
Also move it out of the conditional to make it more visible in case
some other code will be added which may use that pointer. We need
to keep a reference as long as we use the pointer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230102203037.16120-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of calling put_device(&adev->dev) where adev is a pointer
to an ACPI device, use specific call, i.e. acpi_dev_put().
Also move it out of the conditional to make it more visible in case
some other code will be added which may use that pointer. We need
to keep a reference as long as we use the pointer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230102203037.16120-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of calling put_device(&adev->dev) where adev is a pointer
to an ACPI device, use specific call, i.e. acpi_dev_put().
Also move it out of the conditional to make it more visible in case
some other code will be added which may use that pointer. We need
to keep a reference as long as we use the pointer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230102203037.16120-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of calling put_device(&adev->dev) where adev is a pointer
to an ACPI device, use specific call, i.e. acpi_dev_put().
Also move it out of the conditional to make it more visible in case
some other code will be added which may use that pointer. We need
to keep a reference as long as we use the pointer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230102203037.16120-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of calling put_device(&adev->dev) where adev is a pointer
to an ACPI device, use specific call, i.e. acpi_dev_put().
Also move it out of the conditional to make it more visible in case
some other code will be added which may use that pointer. We need
to keep a reference as long as we use the pointer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230102203037.16120-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The variable becomes useless since we moved the snd_soc_jack
structure from a static array to sof_hdmi_pcm structure.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230103073704.722027-1-brent.lu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Claudiu Beznea <claudiu.beznea@microchip.com>:
The following series adds runtime PM and suspend to RAM features for
mchp-pdmc driver.
Along with it 2 cleanup patches were added:
- patch 1/4: use vendor,device.yaml file format for Microchip AT91 ASoC
bindings
- patch 4/4: use FIELD_PREP() in mchp-spdiftx.c
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
This series will extend the IPC ops optionality to cover it up to the existence
of the top level ipc pointer itself. There is no functionality change.
The reason for the extended optionality is that we have "DSPless"
debug/development support coming up (currently it is in SOF's topic/sof-dev
stable branch) initially supporting Intel's HDA platforms.
As the name suggests, in this mode the DSP is completely ignored by the linux
driver stack (no firmware loaded, only using HDA directly).
The DSPless mode is aimed to help us to verify our Linux stack on new platforms
where the firmware is not yet in the state that we can reliably use it, but the
hardware and programming flows can be tested already.
There is no plan to make DSPless a production target for SOF Linux stack.
While this is preparatory series aimed to unblock the DSPless support, it has
been integrated into sof-dev separately and we have lots of new features
depending on it (went in between this set and the DSPless support).
I still have some minor tasks to complete for the DSPless to make it a bit more
versatile, but I don't want to block other, stable features for upstreaming.
Merge series from Uwe Kleine-König <u.kleine-koenig@pengutronix.de>:
Hello,
this patch series removes all platform remove functions that only return
zero below sound/soc. There is no reason to have these, as the only
caller is platform core code doing:
if (drv->remove) {
int ret = drv->remove(dev);
...
}
(in platform_remove()) and so having no remove function is both
equivalent and simpler.
Merge series from Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>:
Some devices like DMIC don't expose native controls or need volume limit
due to possible HW damage. Add support for volume controls allowing to
change volume level in DSP. Maximum volume level is imposed by the
topology file which defines given path.
Instead of using hard coded index value for platform device index,
retrieve the device index based on platform devices created.
In PDM config case, ACP PCI driver retrieves dev index from
pdm_dev_index variable.
This will avoid overhead when multiple endpoint combinations
support is added later.
platform device index will vary based on audio endpoint
configuration.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20221221172855.1618766-3-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactor platform device creation implementation.
Based on platform dev count and pdev mask create platform devices.
Use common API to fill platform dev information.
Use pdev count variable in remove callback for unregistering
platform devices.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20221221172855.1618766-2-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement API to retrieve acp device config and calculate platform
device count and dev mask for platform device node creation.
Currently for DMIC configuration, mask and dev count are calculated.
Same api will be used to extend support for different ACP device
configurations.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20221221172855.1618766-1-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
LOUT output can produce either single-ended stereo signals, or mono
differential signal. Some applications are wired to use LOUT in mono
differential mode. Allow to configure it via device property.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Jarrah Gosbell <kernel@undef.tools>
Link: https://lore.kernel.org/r/20221209105621.39237-1-kernel@undef.tools
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm8940 provides the chip ID information via I2C. In this
patch this information is read and if not matching expected
value, the probe function is aborted.
This prevents from using (i.e. inserting) other wm89* modules
which use the same I2C bus address.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221216094624.3849278-3-lukma@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch enables support for internal wm8940's PLL and proper
divider to set proper value for 256x fs clock.
This approach is more flexible and replaces hardcoded clock
values and makes the codec work with the simple-card driver.
Card drivers calling set_pll() and set_clkdiv() directly are
unaffected.
For the reference - code in this commit is based on:
51b2bb3f25
("ASoC: wm8974: configure pll and mclk divider automatically")
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221216094624.3849278-2-lukma@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
