commit 2fe8a23643 upstream.
Symptom:
In case of a bad cable connection (e.g. dirty optics) a fast sequence of
network DOWN-UP-DOWN-UP could happen. UP triggers recovery of the qeth
interface. In case of a second DOWN while recovery is still ongoing, it
can happen that the IP@ of a Layer3 qeth interface is lost and will not
be recovered by the second UP.
Problem:
When registration of IP addresses with Layer 3 qeth devices fails, (e.g.
because of bad address format) the respective IP address is deleted from
its hash-table in the driver. If registration fails because of a ENETDOWN
condition, the address should stay in the hashtable, so a subsequent
recovery can restore it.
3caa4af834 ("qeth: keep ip-address after LAN_OFFLINE failure")
fixes this for registration failures during normal operation, but not
during recovery.
Solution:
Keep L3-IP address in case of ENETDOWN in qeth_l3_recover_ip(). For
consistency with qeth_l3_add_ip() we also keep it in case of EADDRINUSE,
i.e. for some reason the card already/still has this address registered.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://lore.kernel.org/r/20240206085849.2902775-1-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc4ce46b1e upstream.
The below commit introduced a WARN when phy state is not in the states:
PHY_HALTED, PHY_READY and PHY_UP.
commit 744d23c71a ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
When cpsw resumes, there have port in PHY_NOLINK state, so the below
warning comes out. Set mac_managed_pm be true to tell mdio that the phy
resume/suspend is managed by the mac, to fix the following warning:
WARNING: CPU: 0 PID: 965 at drivers/net/phy/phy_device.c:326 mdio_bus_phy_resume+0x140/0x144
CPU: 0 PID: 965 Comm: sh Tainted: G O 6.1.46-g247b2535b2 #1
Hardware name: Generic AM33XX (Flattened Device Tree)
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x24/0x2c
dump_stack_lvl from __warn+0x84/0x15c
__warn from warn_slowpath_fmt+0x1a8/0x1c8
warn_slowpath_fmt from mdio_bus_phy_resume+0x140/0x144
mdio_bus_phy_resume from dpm_run_callback+0x3c/0x140
dpm_run_callback from device_resume+0xb8/0x2b8
device_resume from dpm_resume+0x144/0x314
dpm_resume from dpm_resume_end+0x14/0x20
dpm_resume_end from suspend_devices_and_enter+0xd0/0x924
suspend_devices_and_enter from pm_suspend+0x2e0/0x33c
pm_suspend from state_store+0x74/0xd0
state_store from kernfs_fop_write_iter+0x104/0x1ec
kernfs_fop_write_iter from vfs_write+0x1b8/0x358
vfs_write from ksys_write+0x78/0xf8
ksys_write from ret_fast_syscall+0x0/0x54
Exception stack(0xe094dfa8 to 0xe094dff0)
dfa0: 00000004 005c3fb8 00000001 005c3fb8 00000004 00000001
dfc0: 00000004 005c3fb8 b6f6bba0 00000004 00000004 0059edb8 00000000 00000000
dfe0: 00000004 bed918f0 b6f09bd3 b6e89a66
Cc: <stable@vger.kernel.org> # v6.0+
Fixes: 744d23c71a ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Fixes: fba863b816 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46f5ab762d upstream.
When we added mount_setattr() I added additional checks compared to the
legacy do_reconfigure_mnt() and do_change_type() helpers used by regular
mount(2). If that mount had a parent then verify that the caller and the
mount namespace the mount is attached to match and if not make sure that
it's an anonymous mount.
The real rootfs falls into neither category. It is neither an anoymous
mount because it is obviously attached to the initial mount namespace
but it also obviously doesn't have a parent mount. So that means legacy
mount(2) allows changing mount properties on the real rootfs but
mount_setattr(2) blocks this. I never thought much about this but of
course someone on this planet of earth changes properties on the real
rootfs as can be seen in [1].
Since util-linux finally switched to the new mount api in 2.39 not so
long ago it also relies on mount_setattr() and that surfaced this issue
when Fedora 39 finally switched to it. Fix this.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2256843
Link: https://lore.kernel.org/r/20240206-vfs-mount-rootfs-v1-1-19b335eee133@kernel.org
Reviewed-by: Jan Kara <jack@suse.cz>
Reported-by: Karel Zak <kzak@redhat.com>
Cc: stable@vger.kernel.org # v5.12+
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64dc40f752 upstream.
When compiling rtla with clang, I am getting the following warnings:
$ make HOSTCC=clang CC=clang LLVM_IAS=1
[..]
clang -O -g -DVERSION=\"6.8.0-rc3\" -flto=auto -fexceptions
-fstack-protector-strong -fasynchronous-unwind-tables
-fstack-clash-protection -Wall -Werror=format-security
-Wp,-D_FORTIFY_SOURCE=2 -Wp,-D_GLIBCXX_ASSERTIONS
$(pkg-config --cflags libtracefs)
-c -o src/osnoise_hist.o src/osnoise_hist.c
src/osnoise_hist.c:138:6: warning: variable 'bucket' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
138 | if (data->bucket_size)
| ^~~~~~~~~~~~~~~~~
src/osnoise_hist.c:149:6: note: uninitialized use occurs here
149 | if (bucket < entries)
| ^~~~~~
src/osnoise_hist.c:138:2: note: remove the 'if' if its condition is always true
138 | if (data->bucket_size)
| ^~~~~~~~~~~~~~~~~~~~~~
139 | bucket = duration / data->bucket_size;
src/osnoise_hist.c:132:12: note: initialize the variable 'bucket' to silence this warning
132 | int bucket;
| ^
| = 0
1 warning generated.
[...]
clang -O -g -DVERSION=\"6.8.0-rc3\" -flto=auto -fexceptions
-fstack-protector-strong -fasynchronous-unwind-tables
-fstack-clash-protection -Wall -Werror=format-security
-Wp,-D_FORTIFY_SOURCE=2 -Wp,-D_GLIBCXX_ASSERTIONS
$(pkg-config --cflags libtracefs)
-c -o src/timerlat_hist.o src/timerlat_hist.c
src/timerlat_hist.c:181:6: warning: variable 'bucket' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
181 | if (data->bucket_size)
| ^~~~~~~~~~~~~~~~~
src/timerlat_hist.c:204:6: note: uninitialized use occurs here
204 | if (bucket < entries)
| ^~~~~~
src/timerlat_hist.c:181:2: note: remove the 'if' if its condition is always true
181 | if (data->bucket_size)
| ^~~~~~~~~~~~~~~~~~~~~~
182 | bucket = latency / data->bucket_size;
src/timerlat_hist.c:175:12: note: initialize the variable 'bucket' to silence this warning
175 | int bucket;
| ^
| = 0
1 warning generated.
This is a legit warning, but data->bucket_size is always > 0 (see
timerlat_hist_parse_args()), so the if is not necessary.
Remove the unneeded if (data->bucket_size) to avoid the warning.
Link: https://lkml.kernel.org/r/6e1b1665cd99042ae705b3e0fc410858c4c42346.1707217097.git.bristot@kernel.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Bill Wendling <morbo@google.com>
Cc: Justin Stitt <justinstitt@google.com>
Cc: Donald Zickus <dzickus@redhat.com>
Fixes: 1eeb6328e8 ("rtla/timerlat: Add timerlat hist mode")
Fixes: 829a6c0b56 ("rtla/osnoise: Add the hist mode")
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5f3193603 upstream.
Fix rtla so that the following commands exit with 0 when help is invoked
rtla osnoise top -h
rtla osnoise hist -h
rtla timerlat top -h
rtla timerlat hist -h
Link: https://lore.kernel.org/linux-trace-devel/20240203001607.69703-1-jkacur@redhat.com
Cc: stable@vger.kernel.org
Fixes: 1eeb6328e8 ("rtla/timerlat: Add timerlat hist mode")
Signed-off-by: John Kacur <jkacur@redhat.com>
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14f08c976f upstream.
Since the sched_priority for SCHED_OTHER is always 0, it makes no
sence to set it.
Setting nice for SCHED_OTHER seems more meaningful.
Link: https://lkml.kernel.org/r/20240207065142.1753909-1-limingming3@lixiang.com
Cc: stable@vger.kernel.org
Fixes: b1696371d8 ("rtla: Helper functions for rtla")
Signed-off-by: limingming3 <limingming3@lixiang.com>
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34a1066981 upstream.
The tascodec_init() of the snd-soc-tas2781-comlib module is called from
snd-soc-tas2781-i2c and snd-hda-scodec-tas2781-i2c modules. It calls
request_firmware_nowait() with parameter THIS_MODULE and a cont/callback
from the latter modules.
The latter modules can be removed while their callbacks are running,
resulting in a general protection failure.
Add module parameter to tascodec_init() so request_firmware_nowait() can
be called with the module of the callback.
Fixes: ef3bcde75d ("ASoC: tas2781: Add tas2781 driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/118dad922cef50525e5aab09badef2fa0eb796e5.1707076603.git.soyer@irl.hu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fcbe487308 upstream.
commit 74ad8ed651 ("ASoC: SOF: ipc3: Implement rx_msg IPC ops")
introduced a new allocation before the upper bounds check in
do_rx_work. As a result A DSP can cause bad allocations if spewing
garbage.
Fixes: 74ad8ed651 ("ASoC: SOF: ipc3: Implement rx_msg IPC ops")
Reported-by: Tim Van Patten <timvp@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://msgid.link/r/20240213123834.4827-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb091ff394 upstream.
Add the MIDR value of Microsoft Azure Cobalt 100, which is a Microsoft
implemented CPU based on r0p0 of the ARM Neoverse N2 CPU, and therefore
suffers from all the same errata.
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240214175522.2457857-1-eahariha@linux.microsoft.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61da7c8e2a upstream.
When we are in a syscall we will only save the FPSIMD subset even though
the task still has access to the full register set, and on context switch
we will only remove TIF_SVE when loading the register state. This means
that the signal handling code should not assume that TIF_SVE means that
the register state is stored in SVE format, it should instead check the
format that was recorded during save.
Fixes: 8c845e2731 ("arm64/sve: Leave SVE enabled on syscall if we don't context switch")
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240130-arm64-sve-signal-regs-v2-1-9fc6f9502782@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58aeb5623c upstream.
Driver shall switch clock source from DLL clock to
OPE clock when power off card to ensure that card
can be identified with OPE clock by BIOS.
Signed-off-by: Fred Ai <fred.ai@bayhubtech.com>
Fixes:4be33cf18703 ("mmc: sdhci-pci-o2micro: Improve card input timing at SDR104/HS200 mode")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240203102908.4683-1-fredaibayhubtech@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14db5f64a9 upstream.
Write error handling is racy and can sometime lead to the error recovery
path wrongly changing the inode size of a sequential zone file to an
incorrect value which results in garbage data being readable at the end
of a file. There are 2 problems:
1) zonefs_file_dio_write() updates a zone file write pointer offset
after issuing a direct IO with iomap_dio_rw(). This update is done
only if the IO succeed for synchronous direct writes. However, for
asynchronous direct writes, the update is done without waiting for
the IO completion so that the next asynchronous IO can be
immediately issued. However, if an asynchronous IO completes with a
failure right before the i_truncate_mutex lock protecting the update,
the update may change the value of the inode write pointer offset
that was corrected by the error path (zonefs_io_error() function).
2) zonefs_io_error() is called when a read or write error occurs. This
function executes a report zone operation using the callback function
zonefs_io_error_cb(), which does all the error recovery handling
based on the current zone condition, write pointer position and
according to the mount options being used. However, depending on the
zoned device being used, a report zone callback may be executed in a
context that is different from the context of __zonefs_io_error(). As
a result, zonefs_io_error_cb() may be executed without the inode
truncate mutex lock held, which can lead to invalid error processing.
Fix both problems as follows:
- Problem 1: Perform the inode write pointer offset update before a
direct write is issued with iomap_dio_rw(). This is safe to do as
partial direct writes are not supported (IOMAP_DIO_PARTIAL is not
set) and any failed IO will trigger the execution of zonefs_io_error()
which will correct the inode write pointer offset to reflect the
current state of the one on the device.
- Problem 2: Change zonefs_io_error_cb() into zonefs_handle_io_error()
and call this function directly from __zonefs_io_error() after
obtaining the zone information using blkdev_report_zones() with a
simple callback function that copies to a local stack variable the
struct blk_zone obtained from the device. This ensures that error
handling is performed holding the inode truncate mutex.
This change also simplifies error handling for conventional zone files
by bypassing the execution of report zones entirely. This is safe to
do because the condition of conventional zones cannot be read-only or
offline and conventional zone files are always fully mapped with a
constant file size.
Reported-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Fixes: 8dcc1a9d90 ("fs: New zonefs file system")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10c02aad11 upstream.
The rule inside kvm enforces that the vcpu->mutex is taken *inside*
kvm->lock. The rule is violated by the pkvm_create_hyp_vm() which acquires
the kvm->lock while already holding the vcpu->mutex lock from
kvm_vcpu_ioctl(). Avoid the circular locking dependency altogether by
protecting the hyp vm handle with the config_lock, much like we already
do for other forms of VM-scoped data.
Signed-off-by: Sebastian Ene <sebastianene@google.com>
Cc: stable@vger.kernel.org
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240124091027.1477174-2-sebastianene@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4860abb91f upstream.
The conversion to netfs in the 6.3 kernel caused a regression when
maximum write size is set by the server to an unexpected value which is
not a multiple of 4096 (similarly if the user overrides the maximum
write size by setting mount parm "wsize", but sets it to a value that
is not a multiple of 4096). When negotiated write size is not a
multiple of 4096 the netfs code can skip the end of the final
page when doing large sequential writes, causing data corruption.
This section of code is being rewritten/removed due to a large
netfs change, but until that point (ie for the 6.3 kernel until now)
we can not support non-standard maximum write sizes.
Add a warning if a user specifies a wsize on mount that is not
a multiple of 4096 (and round down), also add a change where we
round down the maximum write size if the server negotiates a value
that is not a multiple of 4096 (we also have to check to make sure that
we do not round it down to zero).
Reported-by: "R. Diez" <rdiez-2006@rd10.de>
Fixes: d08089f649 ("cifs: Change the I/O paths to use an iterator rather than a page list")
Suggested-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Acked-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Tested-by: Matthew Ruffell <matthew.ruffell@canonical.com>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Cc: stable@vger.kernel.org # v6.3+
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4508ec1735 upstream.
When uid, gid and cruid are not specified, we need to dynamically
set them into the filesystem context used for automounting otherwise
they'll end up reusing the values from the parent mount.
Fixes: 9fd29a5bae ("cifs: use fs_context for automounts")
Reported-by: Shane Nehring <snehring@iastate.edu>
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2259257
Cc: stable@vger.kernel.org # 6.2+
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec4d82f855 upstream.
The bit 23, CM TBT3 Not Supported (CNS), in ROUTER_CS_5 indicates
whether a USB4 Connection Manager is TBT3-Compatible and should be:
0b for TBT3-Compatible
1b for Not TBT3-Compatible
Fixes: b04079837b ("thunderbolt: Add initial support for USB4")
Cc: stable@vger.kernel.org
Signed-off-by: Mohammad Rahimi <rahimi.mhmmd@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af9acbfc2c upstream.
When updating the affinity of a VPE, the VMOVP command is currently skipped
if the two CPUs are part of the same VPE affinity.
But this is wrong, as the doorbell corresponding to this VPE is still
delivered on the 'old' CPU, which screws up the balancing. Furthermore,
offlining that 'old' CPU results in doorbell interrupts generated for this
VPE being discarded.
The harsh reality is that VMOVP cannot be elided when a set_affinity()
request occurs. It needs to be obeyed, and if an optimisation is to be
made, it is at the point where the affinity change request is made (such as
in KVM).
Drop the VMOVP elision altogether, and only use the vpe_table_mask
to try and stay within the same ITS affinity group if at all possible.
Fixes: dd3f050a21 (irqchip/gic-v4.1: Implement the v4.1 flavour of VMOVP)
Reported-by: Kunkun Jiang <jiangkunkun@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240213101206.2137483-4-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b02da04ad upstream.
While refactoring the way the ITSs are probed, the handling of quirks
applicable to ACPI-based platforms was lost. As a result, systems such as
HIP07 lose their GICv4 functionnality, and some other may even fail to
boot, unless they are configured to boot with DT.
Move the enabling of quirks into its_probe_one(), making it common to all
firmware implementations.
Fixes: 9585a495ac ("irqchip/gic-v3-its: Split allocation from initialisation of its_node")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240213101206.2137483-3-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0344d6854 upstream.
It was observed on Broadcom devices that use GIC v3 architecture L1
interrupt controllers as the parent of brcmstb-l2 interrupt controllers
that the deactivation of the parent interrupt could happen before the
brcmstb-l2 deasserted its output. This would lead the GIC to reactivate the
interrupt only to find that no L2 interrupt was pending. The result was a
spurious interrupt invoking handle_bad_irq() with its associated
messaging. While this did not create a functional problem it is a waste of
cycles.
The hazard exists because the memory mapped bus writes to the brcmstb-l2
registers are buffered and the GIC v3 architecture uses a very efficient
system register write to deactivate the interrupt.
Add a write memory barrier prior to invoking chained_irq_exit() to
introduce a dsb(st) on those systems to ensure the system register write
cannot be executed until the memory mapped writes are visible to the
system.
[ florian: Added Fixes tag ]
Fixes: 7f646e9276 ("irqchip: brcmstb-l2: Add Broadcom Set Top Box Level-2 interrupt controller")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240210012449.3009125-1-florian.fainelli@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7198383ef upstream.
A DoS tool that injects loads of authentication frames made our AP
crash. The iwl_mvm_is_dup() function couldn't find the per-queue
dup_data which was not allocated.
The root cause for that is that we ran out of stations in the firmware
and we didn't really add the station to the firmware, yet we didn't
return an error to mac80211.
Mac80211 was thinking that we have the station and because of that,
sta_info::uploaded was set to 1. This allowed
ieee80211_find_sta_by_ifaddr() to return a valid station object, but
that ieee80211_sta didn't have any iwl_mvm_sta object initialized and
that caused the crash mentioned earlier when we got Rx on that station.
Cc: stable@vger.kernel.org
Fixes: 57974a55d9 ("wifi: iwlwifi: mvm: refactor iwl_mvm_mac_sta_state_common()")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206175739.1f76c44b2486.I6a00955e2842f15f0a089db2f834adb9d10fbe35@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c98d8836b8 upstream.
This pointer can change here since the SKB can change, so we
actually later open-coded IEEE80211_SKB_CB() again. Reload
the pointer where needed, so the monitor-mode case using it
gets fixed, and then use info-> later as well.
Cc: stable@vger.kernel.org
Fixes: 5316821590 ("mac80211: fix VLAN handling with TXQs")
Link: https://msgid.link/20240131164910.b54c28d583bc.I29450cec84ea6773cff5d9c16ff92b836c331471@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b743287d7a upstream.
When a wiphy work is queued with timer, and then again
without a delay, it's started immediately but *also*
started again after the timer expires. This can lead,
for example, to warnings in mac80211's offchannel code
as reported by Jouni. Running the same work twice isn't
expected, of course. Fix this by deleting the timer at
this point, when queuing immediately due to delay=0.
Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Fixes: a3ee4dc84c ("wifi: cfg80211: add a work abstraction with special semantics")
Link: https://msgid.link/20240125095108.2feb0eaaa446.I4617f3210ed0e7f252290d5970dac6a876aa595b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 353d321f63 upstream.
The storage for the TLV PC register data wasn't done like all
the other storage in the drv->fw area, which is cleared at the
end of deallocation. Therefore, the freeing must also be done
differently, explicitly NULL'ing it out after the free, since
otherwise there's a nasty double-free bug here if a file fails
to load after this has been parsed, and we get another free
later (e.g. because no other file exists.) Fix that by adding
the missing NULL assignment.
Cc: stable@vger.kernel.org
Fixes: 5e31b3df86 ("wifi: iwlwifi: dbg: print pc register data once fw dump occurred")
Reported-by: Guy Kaplan <guy.kaplan@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.675f3c24ec0d.I6ab4015cd78d82dd95471f840629972ef0331de3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a1c13303f upstream.
When physical ports are reset (either through link failure or manually
toggled down and up again) that are slaved to a Linux bond with a tunnel
endpoint IP address on the bond device, not all tunnel packets arriving
on the bond port are decapped as expected.
The bond dev assigns the same MAC address to itself and each of its
slaves. When toggling a slave device, the same MAC address is therefore
offloaded to the NFP multiple times with different indexes.
The issue only occurs when re-adding the shared mac. The
nfp_tunnel_add_shared_mac() function has a conditional check early on
that checks if a mac entry already exists and if that mac entry is
global: (entry && nfp_tunnel_is_mac_idx_global(entry->index)). In the
case of a bonded device (For example br-ex), the mac index is obtained,
and no new index is assigned.
We therefore modify the conditional in nfp_tunnel_add_shared_mac() to
check if the port belongs to the LAG along with the existing checks to
prevent a new global mac index from being re-assigned to the slave port.
Fixes: 20cce88650 ("nfp: flower: enable MAC address sharing for offloadable devs")
CC: stable@vger.kernel.org # 5.1+
Signed-off-by: Daniel de Villiers <daniel.devilliers@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f4d6f011b upstream.
Enable previously excluded xdp feature flag for NFD3 devices. This
feature flag is required in order to bind nfp interfaces to an xdp
socket and the nfp driver does in fact support the feature.
Fixes: 66c0e13ad2 ("drivers: net: turn on XDP features")
Cc: stable@vger.kernel.org # 6.3+
Signed-off-by: James Hershaw <james.hershaw@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3d4f7f228 upstream.
The 1st and 2nd expansion BAR configuration registers are configured,
when the driver starts up, in variables 'barcfg_msix_general' and
'barcfg_msix_xpb', respectively. The 'LengthSelect' field is ORed in
from bit 0, which is incorrect. The 'LengthSelect' field should
start from bit 27.
This has largely gone un-noticed because
NFP_PCIE_BAR_PCIE2CPP_LengthSelect_32BIT happens to be 0.
Fixes: 4cb584e0ee ("nfp: add CPP access core")
Cc: stable@vger.kernel.org # 4.11+
Signed-off-by: Daniel Basilio <daniel.basilio@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24c890dd71 upstream.
When a zero-length message is hashed by algif_hash, and an error
is triggered, it tries to free an SG list that was never allocated
in the first place. Fix this by not freeing the SG list on the
zero-length error path.
Reported-by: Shigeru Yoshida <syoshida@redhat.com>
Reported-by: xingwei lee <xrivendell7@gmail.com>
Fixes: b6d972f689 ("crypto: af_alg/hash: Fix recvmsg() after sendmsg(MSG_MORE)")
Cc: <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reported-by: syzbot+3266db0c26d1fbbe3abb@syzkaller.appspotmail.com
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38296afe3c upstream.
Syzbot reported a hang issue in migrate_pages_batch() called by mbind()
and nilfs_lookup_dirty_data_buffers() called in the log writer of nilfs2.
While migrate_pages_batch() locks a folio and waits for the writeback to
complete, the log writer thread that should bring the writeback to
completion picks up the folio being written back in
nilfs_lookup_dirty_data_buffers() that it calls for subsequent log
creation and was trying to lock the folio. Thus causing a deadlock.
In the first place, it is unexpected that folios/pages in the middle of
writeback will be updated and become dirty. Nilfs2 adds a checksum to
verify the validity of the log being written and uses it for recovery at
mount, so data changes during writeback are suppressed. Since this is
broken, an unclean shutdown could potentially cause recovery to fail.
Investigation revealed that the root cause is that the wait for writeback
completion in nilfs_page_mkwrite() is conditional, and if the backing
device does not require stable writes, data may be modified without
waiting.
Fix these issues by making nilfs_page_mkwrite() wait for writeback to
finish regardless of the stable write requirement of the backing device.
Link: https://lkml.kernel.org/r/20240131145657.4209-1-konishi.ryusuke@gmail.com
Fixes: 1d1d1a7672 ("mm: only enforce stable page writes if the backing device requires it")
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+ee2ae68da3b22d04cd8d@syzkaller.appspotmail.com
Closes: https://lkml.kernel.org/r/00000000000047d819061004ad6c@google.com
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67b8bcbaed upstream.
The helper function nilfs_recovery_copy_block() of
nilfs_recovery_dsync_blocks(), which recovers data from logs created by
data sync writes during a mount after an unclean shutdown, incorrectly
calculates the on-page offset when copying repair data to the file's page
cache. In environments where the block size is smaller than the page
size, this flaw can cause data corruption and leak uninitialized memory
bytes during the recovery process.
Fix these issues by correcting this byte offset calculation on the page.
Link: https://lkml.kernel.org/r/20240124121936.10575-1-konishi.ryusuke@gmail.com
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4639c50210 upstream.
The SWS JS201D need a different pinconfig from windows driver.
Add a quirk to use a specific pinconfig to SWS JS201D.
Signed-off-by: bo liu <bo.liu@senarytech.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240205013802.51907-1-bo.liu@senarytech.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32f03f4002 upstream.
The HP mt645 G7 Thin Client uses an ALC236 codec and needs the
ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF quirk to make the mute and
micmute LEDs work.
There are two variants of the USB-C PD chip on this device. Each uses
a different BIOS and board ID, hence the two entries.
Signed-off-by: Eniac Zhang <eniac-xw.zhang@hp.com>
Signed-off-by: Alexandru Gagniuc <alexandru.gagniuc@hp.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240215154922.778394-1-alexandru.gagniuc@hp.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc9432c4fb upstream.
This change uses the appropriate _cansleep or non-sleeping API for
reading GPIO read-only state. This allows users with GPIOs that
never sleepbeing called in atomic context.
Implement the same mechanism as in commit 52af318c93 ("mmc: Allow
non-sleeping GPIO cd").
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240206083912.2543142-1-alexander.stein@ew.tq-group.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a37ee9e117 upstream.
If we hit CQ ring overflow when attempting to post a multishot accept
completion, we don't properly save the result or return code. This
results in losing the accepted fd value.
Instead, we return the result from the poll operation that triggered
the accept retry. This is generally POLLIN|POLLPRI|POLLRDNORM|POLLRDBAND
which is 0xc3, or 195, which looks like a valid file descriptor, but it
really has no connection to that.
Handle this like we do for other multishot completions - assign the
result, and return IOU_STOP_MULTISHOT to cancel any further completions
from this request when overflow is hit. This preserves the result, as we
should, and tells the application that the request needs to be re-armed.
Cc: stable@vger.kernel.org
Fixes: 515e269612 ("io_uring: revert "io_uring fix multishot accept ordering"")
Link: https://github.com/axboe/liburing/issues/1062
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d794734c9b upstream.
When ident_pud_init() uses only gbpages to create identity maps, large
ranges of addresses not actually requested can be included in the
resulting table; a 4K request will map a full GB. On UV systems, this
ends up including regions that will cause hardware to halt the system
if accessed (these are marked "reserved" by BIOS). Even processor
speculation into these regions is enough to trigger the system halt.
Only use gbpages when map creation requests include the full GB page
of space. Fall back to using smaller 2M pages when only portions of a
GB page are included in the request.
No attempt is made to coalesce mapping requests. If a request requires
a map entry at the 2M (pmd) level, subsequent mapping requests within
the same 1G region will also be at the pmd level, even if adjacent or
overlapping such requests could have been combined to map a full
gbpage. Existing usage starts with larger regions and then adds
smaller regions, so this should not have any great consequence.
[ dhansen: fix up comment formatting, simplifty changelog ]
Signed-off-by: Steve Wahl <steve.wahl@hpe.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20240126164841.170866-1-steve.wahl%40hpe.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05519c86d6 upstream.
Use a u64 instead of a u8 when taking a snapshot of pmu->fixed_ctr_ctrl
when reprogramming fixed counters, as truncating the value results in KVM
thinking fixed counter 2 is already disabled (the bug also affects fixed
counters 3+, but KVM doesn't yet support those). As a result, if the
guest disables fixed counter 2, KVM will get a false negative and fail to
reprogram/disable emulation of the counter, which can leads to incorrect
counts and spurious PMIs in the guest.
Fixes: 76d287b234 ("KVM: x86/pmu: Drop "u8 ctrl, int idx" for reprogram_fixed_counter()")
Cc: stable@vger.kernel.org
Signed-off-by: Mingwei Zhang <mizhang@google.com>
Link: https://lore.kernel.org/r/20240123221220.3911317-1-mizhang@google.com
[sean: rewrite changelog to call out the effects of the bug]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6231c9e1a9 upstream.
kvm_vcpu_ioctl_x86_set_vcpu_events() routine makes 'KVM_REQ_NMI'
request for a vcpu even when its 'events->nmi.pending' is zero.
Ex:
qemu_thread_start
kvm_vcpu_thread_fn
qemu_wait_io_event
qemu_wait_io_event_common
process_queued_cpu_work
do_kvm_cpu_synchronize_post_init/_reset
kvm_arch_put_registers
kvm_put_vcpu_events (cpu, level=[2|3])
This leads vCPU threads in QEMU to constantly acquire & release the
global mutex lock, delaying the guest boot due to lock contention.
Add check to make KVM_REQ_NMI request only if vcpu has NMI pending.
Fixes: bdedff2631 ("KVM: x86: Route pending NMIs from userspace through process_nmi()")
Cc: stable@vger.kernel.org
Signed-off-by: Prasad Pandit <pjp@fedoraproject.org>
Link: https://lore.kernel.org/r/20240103075343.549293-1-ppandit@redhat.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d877550eaf upstream.
Before this change, the expected size of the user space buffer was
taken from fx_sw->xstate_size. fx_sw->xstate_size can be changed
from user-space, so it is possible construct a sigreturn frame where:
* fx_sw->xstate_size is smaller than the size required by valid bits in
fx_sw->xfeatures.
* user-space unmaps parts of the sigrame fpu buffer so that not all of
the buffer required by xrstor is accessible.
In this case, xrstor tries to restore and accesses the unmapped area
which results in a fault. But fault_in_readable succeeds because buf +
fx_sw->xstate_size is within the still mapped area, so it goes back and
tries xrstor again. It will spin in this loop forever.
Instead, fault in the maximum size which can be touched by XRSTOR (taken
from fpstate->user_size).
[ dhansen: tweak subject / changelog ]
Fixes: fcb3635f50 ("x86/fpu/signal: Handle #PF in the direct restore path")
Reported-by: Konstantin Bogomolov <bogomolov@google.com>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrei Vagin <avagin@google.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc:stable@vger.kernel.org
Link: https://lore.kernel.org/all/20240130063603.3392627-1-avagin%40google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6a1892585 upstream.
The kernel built with MCRUSOE is unbootable on Transmeta Crusoe. It shows
the following error message:
This kernel requires an i686 CPU, but only detected an i586 CPU.
Unable to boot - please use a kernel appropriate for your CPU.
Remove MCRUSOE from the condition introduced in commit in Fixes, effectively
changing X86_MINIMUM_CPU_FAMILY back to 5 on that machine, which matches the
CPU family given by CPUID.
[ bp: Massage commit message. ]
Fixes: 25d76ac888 ("x86/Kconfig: Explicitly enumerate i686-class CPUs in Kconfig")
Signed-off-by: Aleksander Mazur <deweloper@wp.pl>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/20240123134309.1117782-1-deweloper@wp.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7be50f2e8f upstream.
Emil reports:
After updating Linux on an i.MX28 board, serial communication over
AUART broke. When I TX from the board and measure on the TX pin, it
seems like the HW fifo is not emptied before the transmission is
stopped.
MXS performs weird things with stop_tx(). The driver makes it
conditional on uart_tx_stopped().
So the driver needs special handling. Pass the brand new UART_TX_NOSTOP
to uart_port_tx_flags() and handle the stop on its own.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reported-by: Emil Kronborg <emil.kronborg@protonmail.com>
Cc: stable <stable@kernel.org>
Fixes: 2d141e683e ("tty: serial: use uart_port_tx() helper")
Closes: https://lore.kernel.org/all/miwgbnvy3hjpnricubg76ytpn7xoceehwahupy25bubbduu23s@om2lptpa26xw/
Tested-by: Stefan Wahren <wahrenst@gmx.net>
Tested-by: Emil Kronborg <emil.kronborg@protonmail.com>
Link: https://lore.kernel.org/r/20240201105557.28043-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ee07964d4 upstream.
And an enum with a flag: UART_TX_NOSTOP. To NOT call
__port->ops->stop_tx() when the circular buffer is empty. mxs-uart needs
this (see the next patch).
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: stable <stable@kernel.org>
Tested-by: Emil Kronborg <emil.kronborg@protonmail.com>
Link: https://lore.kernel.org/r/20240201105557.28043-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbecc9fcbb upstream.
powerVM hypervisor updates the VPA fields with stolen time data.
It currently reports enqueue_dispatch_tb and ready_enqueue_tb for
this purpose. In linux these two fields are used to report the stolen time.
The VPA fields are updated at the TB frequency. On powerPC its mostly
set at 512Mhz. Hence this needs a conversion to ns when reporting it
back as rest of the kernel timings are in ns. This conversion is already
handled in tb_to_ns function. So use that function to report accurate
stolen time.
Observed this issue and used an Capped Shared Processor LPAR(SPLPAR) to
simplify the experiments. In all these cases, 100% VP Load is run using
stress-ng workload. Values of stolen time is in percentages as reported
by mpstat. With the patch values are close to expected.
6.8.rc1 +Patch
12EC/12VP 0.0 0.0
12EC/24VP 25.7 50.2
12EC/36VP 37.3 69.2
12EC/48VP 38.5 78.3
Fixes: 0e8a631328 ("powerpc/pseries: Implement CONFIG_PARAVIRT_TIME_ACCOUNTING")
Cc: stable@vger.kernel.org # v6.1+
Signed-off-by: Shrikanth Hegde <sshegde@linux.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240213052635.231597-1-sshegde@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb6d871f4b upstream.
Commit e320a76db4 ("powerpc/cputable: Split cpu_specs[] out of
cputable.h") moved the cpu_specs to separate header files. Previously
PPC_FEATURE_BOOKE was enabled by CONFIG_PPC_BOOK3E_64. The definition in
cpu_specs_e500mc.h for PPC64 no longer enables PPC_FEATURE_BOOKE.
This breaks user space reading the ELF hwcaps and expect
PPC_FEATURE_BOOKE. Debugging an application with gdb is no longer
working on e5500/e6500 because the 64-bit detection relies on
PPC_FEATURE_BOOKE for Book-E.
Fixes: e320a76db4 ("powerpc/cputable: Split cpu_specs[] out of cputable.h")
Cc: stable@vger.kernel.org # v6.1+
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240207092758.1058893-1-david.engraf@sysgo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
