Currently the driver always configures the sensor for dual-lane MIPI
output, but it also supports single-lane output. Add support for that by
checking the data-lanes fwnode property how many lanes are used and
configure the necessary registers based on that.
To achieve this we move setting register 0x3018 out of the general reg
sequence so we set it to the correct value. The pixel_rate value also
needs to be adjusted.
[Sakari Ailus: Use div_s64 to divide a 64-bit number]
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace the unusual const char *err_msg usage with dev_err_probe which
also handles -EPROBE_DEFER better by not printing the message to kmsg.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Convert the Samsung S5C73M3 8Mp camera ISP bindings to DT schema.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Convert the Samsung S5P/Exynos Camera Subsystem (FIMC) bindings to DT
schema. Changes during conversion - adjust to existing DTS and Linux
driver: add iommus and power-domains.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Convert the Samsung Exynos4212/4412 SoC Imaging Subsystem (FIMC-IS)
bindings to DT schema. Changes during conversion - adjust to existing
DTS and Linux driver: add iommus and power-domains.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Convert the Samsung Exynos SoC series camera host interface (FIMC-LITE)
bindings to DT schema. Changes during conversion - adjust to existing
DTS and Linux driver: add iommus and power-domains.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Convert the Samsung S5P/Exynos SoC series MIPI CSI-2 receiver (MIPI
CSIS) bindings to DT schema. Changes during conversion - adjust to
existing DTS and Linux driver:
1. Add phys and power-domains.
2. Move samsung,csis-wclk property to the endpoint node.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Convert the Samsung S5K6A3(YX) raw image sensor bindings to DT schema.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The FIMC camera node wrapper is not a bus, so using simple-bus fallback
compatible just to instantiate its children nodes was never correct.
Driver should explicitly populate all its children devices.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Driver does not handle pin configuration switching and several DTS
provide empty pinctrl property, just to satisfy the driver's requirement
for it. Drop requirement for pinctrl property as it is really optional.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The FIMC camera node wrapper is not a bus, so using simple-bus fallback
compatible just to instantiate its children nodes was never correct.
Drop the simple-bus compatible and expect driver to explicitly populate
children devices.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The documentation for the VIDIOC_SUBDEV_ENUM_FRAME_SIZE ioctl
incorrectly refers to struct v4l2_subdev_mbus_code_enum as the
parameter. Fix this.
[Sakari Ailus: Rebased on top of Dorota's documentation patch]
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This clarifies which side of the calls is responsible for doing what to
which parts of the struct. It also expands the terse description of the
access algorithm into more prose-like, active voice description, which
trades conciseness for ease of comprehension.
Fixed: typo "format" -> "frame size" in enum-frame-size
Added: no holes in the enumeration
Added: enumerations per what?
Added: who fills in what in calls
Changed: "given" -> "specified"
[Sakari Ailus: Rewrap text]
Signed-off-by: Dorota Czaplejewicz <dorota.czaplejewicz@puri.sm>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This clarifies which side of the calls is responsible for doing what to
which parts of the struct. This also explicitly states that repeating
values are disallowed. It also expands the terse description of the access
algorithm into more prose-like, active voice description, which trades
conciseness for ease of comprehension.
Added: mbus codes must not repeat
Added: no holes in the enumeration
Added: enumerations per what?
Added: who fills in what in calls
Changed: "zero" -> "0"
Changed: "given" -> "specified"
Still unclear how it works so didn't describe: "which". What is a "try
format" vs "active format"?
[Sakari Ailus: Rewrap lines, fix build issue]
Signed-off-by: Dorota Czaplejewicz <dorota.czaplejewicz@puri.sm>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Both sensors are quite similar. Their specs only differ regarding LVDS
and parallel output but are identical regarding MIPI-CSI-2 interface.
But they use a different init setting of hard-coded values, taken from
the datasheet.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The imx290 driver can be used for both imx290 and imx327 as they have a
similar register set and configuration. imx327 lacks 8 lanes LVDS and
120 FPS support.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
imx290_start_streaming logs what failed, but not the error
code from that function. Add it into the log message.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The sensor supports H & V flips, so add the relevant hooks for
V4L2_CID_HFLIP and V4L2_CID_VFLIP to configure them.
Note that the Bayer order is maintained as the readout area
shifts by 1 pixel in the appropriate direction (note the
comment about the top margin being 8 pixels whilst the bottom
margin is 9). The V4L2_SEL_TGT_CROP region is therefore
adjusted appropriately.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The sensor supports either a 37.125 or 74.25MHz external, but
the driver only supported 37.125MHz.
Add the relevant register configuration for either clock
frequency option.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
IMX290_CTRL_07 was written from both imx290_global_init_settings
and imx290_1080p_settings and imx290_720p_settings.
Remove it from imx290_global_init_settings as the setting varies
based on the mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The default VMAX for 60fps in 720p mode is 750 according to the
datasheet, however the driver always left it at 1125 thereby stopping
60fps being achieved.
Make VMAX (and therefore V4L2_CID_VBLANK) mode dependent so that 720p60
can be achieved.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver exposed V4L2_CID_VBLANK as a read only control to allow
for exposure calculations and determination of the frame rate.
Convert to a read/write control so that the frame rate can be
controlled.
V4L2_CID_VBLANK also sets the limits for the exposure control,
therefore exposure ranges have to be updated when vblank changes
(either via s_ctrl, or via changing mode).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver exposed V4L2_CID_HBLANK as a read only control to allow
for exposure calculations and determination of the frame rate.
Convert to a read/write control so that the frame rate can be
controlled.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Commit "98e0500eadb7 media: i2c: imx290: Add configurable link frequency
and pixel rate" added support for the increased link frequencies
on 2 data lanes, but didn't update the CSI timing registers in
accordance with the datasheet.
Use the specified settings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Commit "97589ad61c73 media: i2c: imx290: Add support for 2 data lanes"
added support for running in two lane mode (instead of 4), but
without changing the link frequency that resulted in a max of 30fps.
Commit "98e0500eadb7 media: i2c: imx290: Add configurable link frequency
and pixel rate" then doubled the link frequency when in 2 lane mode,
but didn't undo the correction for running at only 30fps, just extending
horizontal blanking instead.
Remove the 30fps limit on 2 lane by correcting the register config
in accordance with the datasheet for 60fps operation over 2 lanes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The datasheet lists the link frequency changes between
1080p and 720p modes. This is correct that the link frequency
changes as measured on an oscilloscope.
Link frequency is not necessarily the same as pixel rate.
The datasheet gives standard configurations for 1080p and 720p
modes at a number of frame rates.
Looking at the 1080p mode it gives:
HMAX = 0x898 = 2200
VMAX = 0x465 = 1125
2200 * 1125 * 60fps = 148.5MPix/s
Looking at the 720p mode it gives:
HMAX = 0xce4 = 3300
VMAX = 0x2ee = 750
3300 * 750 * 60fps = 148.5Mpix/s
This driver currently scales the pixel rate proportionally to the
link frequency, however the above shows that this is not the
correct thing to do, and currently all frame rate and exposure
calculations give incorrect results.
Correctly report the pixel rate as being 148.5MPix/s under any
mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Any V4L2 subdevice that implements controls and declares
V4L2_SUBDEV_FL_HAS_DEVNODE should also declare V4L2_SUBDEV_FL_HAS_EVENTS
and implement subscribe_event and unsubscribe_event hooks.
This driver didn't and would therefore fail v4l2-compliance
testing.
Add the relevant hooks.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The colorspace fields were left untouched in imx290_set_fmt
which lead to a v4l2-compliance failure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The IMX290 module is available as either mono or colour (Bayer).
Update the driver so that it can advertise the correct mono
formats instead of the colour ones.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The IMX290 module is available as either monochrome or colour and
the variant is not detectable at runtime.
Add a new compatible string for the monochrome version, based on the
full device name IMX290LLR. For consistency, add a new compatible string
for the colour version based on the IMX290LQR full device name, and
deprecate the current ambiguous compatible string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ov5647_read() functions calls i2c_master_send() and
i2c_master_read() in sequence. However this leaves space for other
clients to contend the bus and insert an unrelated transaction in between
the two calls.
Replace the two calls with a single i2c_transfer() one, that locks the
bus in between the transactions.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
No need to call fwnode_property_read_u32(dev_fwnode()), when
we have already existing helper. So use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Since we have a proper endianness converters for LE 24-bit data use them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
A common case with subdev routing is that on the subdevice just before
the DMA engines (video nodes), no multiplexing is allowed on the source
pads, as the DMA engine can only handle a single stream.
In some other situations one might also want to do the same check on the
sink side.
Add new routing validation flags to check these:
V4L2_SUBDEV_ROUTING_NO_SINK_MULTIPLEXING and
V4L2_SUBDEV_ROUTING_NO_SOURCE_MULTIPLEXING.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
V4L2_SUBDEV_ROUTING_NO_STREAM_MIX routing validation flag means that all
routes from a sink pad must go to the same source pad and all routes
going to the same source pad must originate from the same sink pad.
This does not cover all use cases. For example, if a device routes
all streams from a single sink pad to any of the source pads, but
streams from multiple sink pads can go to the same source pad, the
current flag is too restrictive.
Split the flag into two parts, V4L2_SUBDEV_ROUTING_NO_SINK_STREAM_MIX
and V4L2_SUBDEV_ROUTING_NO_SOURCE_STREAM_MIX, which add the restriction
only on one side of the device. Together they mean the same as
V4L2_SUBDEV_ROUTING_NO_STREAM_MIX.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Route validation docs use the word 'may'. Change that to 'shall' for
emphasis.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
tx_from_ep's for loop uses '5' as bound, while in fact it refers to the
number of polarities. Replace it by VGXY61_NB_POLARITIES for
factorization.
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In case of error 'update_hdr' now goes through 'power_off' instead of
returning, effectively shutting down the sensor.
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Previously the device detection was performed after patching.
Move it right after the reset to make sure we have the correct sensor
before trying to patch it.
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
At this stage the default mode is unknown.
This is done correctly by vgxy61_fill_framefmt right after.
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Support for clipping for overlays has been removed, update the
documentation.
Support for destructive overlay support has been removed as well,
also update the documentation for this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Make sure this field is always 0 since destructive overlays
are no longer supported.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
These two capabilities are no longer supported, so no
longer define them when compiling the kernel.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There are no longer any drivers that support clipping and bitmap
support for the capture or output overlay interfaces, so drop
this.
Always set the bitmap, clips and clipcount fields to 0, and
remove the compat32 support.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This test driver is the only remaining driver still using
the clipping and bitmap method. Drop support for this so
we can remove this in the V4L2 API as well.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Destructive overlay support (i.e. where the video frame is DMA-ed
straight into a framebuffer) is effectively dead. It was a
necessary evil in the early days when computers were not fast enough
to copy SDTV video frames around, but today that's no longer a problem.
It requires access to the framebuffer memory, which is a bad idea and
very hard to do safely. In addition, in drm it is today almost
impossible to get hold of the framebuffer address.
So drop support for this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Destructive overlay support (i.e. where the video frame is DMA-ed
straight into a framebuffer) is effectively dead. It was a
necessary evil in the early days when computers were not fast enough
to copy SDTV video frames around, but today that's no longer a problem.
It requires access to the framebuffer memory, which is a bad idea and
very hard to do safely. In addition, in drm it is today almost
impossible to get hold of the framebuffer address.
So drop support for this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
