The lock_kernel call moved into the fs for umount_begin
is not needed. This adds a check to make sure we don't
call umount_begin twice on the same fs.
umount_begin for cifs is probably not needed and
may eventually be able to be removed, but in
the meantime this smaller patch is safe and
gets rid of the bkl from this path which provides
some benefit.
Acked-by: Jeff Layton <redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
FreeXid() along with freeing Xid does add a cifsFYI debug message that
prints rc (return code) as well. In some code paths where we set/return
error code after calling FreeXid(), incorrect error code is being
printed when cifsFYI is enabled.
This could be misleading in few cases. For eg.
In cifs_open() if cifs_fill_filedata() returns a valid pointer to
cifsFileInfo, FreeXid() prints rc=-13 whereas 0 is actually being
returned. Fix this by setting rc before calling FreeXid().
Basically convert
FreeXid(xid); rc = -ERR;
return -ERR; => FreeXid(xid);
return rc;
[Note that Christoph would like to replace the GetXid/FreeXid
calls, which are primarily used for debugging. This seems
like a good longer term goal, but although there is an
alternative tracing facility, there are no examples yet
available that I know of that we can use (yet) to
convert this cifs function entry/exit logging, and for
creating an identifier that we can use to correlate
all dmesg log entries for a particular vfs operation
(ie identify all log entries for a particular vfs
request to cifs: e.g. a particular close or read or write
or byte range lock call ... and just using the thread id
is harder). Eventually when a replacement
for this is available (e.g. when NFS switches over and various
samples to look at in other file systems) we can remove the
GetXid/FreeXid macro but in the meantime multiple people
use this run time configurable logging all the time
for debugging, and Suresh's patch fixes a problem
which made it harder to notice some low
memory problems in the log so it is worthwhile
to fix this problem until a better logging
approach is able to be used]
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Also removes obsolete distinction between rawntlmssp and ntlmssp (in asn/SPNEGO)
since as jra noted we can always send raw ntlmssp in session setup now.
remove check for experimental runtime flag (/proc/fs/cifs/Experimental) in
ntlmssp path.
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
cifs: remove rw/ro options
These options are handled at the VFS layer. They only ever set the
option in the smb_vol struct. Nothing was ever done with them afterward
anyway.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
cifs: fix problems with earlier patches
cifs_show_address hasn't been introduced yet, and fix a typo that was
silently fixed by a later patch in the series.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
This patch has CIFS look for a '%' in an IPv6 address. If one is
present then it will try to treat that value as a numeric interface
index suitable for stuffing into the sin6_scope_id field.
This should allow people to mount servers on IPv6 link-local addresses.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Acked-by: David Holder <david@erion.co.uk>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Noticed this when tree connect timed out (due to Samba server crash) -
we try to send a tree disconnect for a tid that does not exist
since we don't have a valid tree id yet. This checks that the
session is valid before sending the tree disconnect to handle
this case.
Signed-off-by: Steve French <sfrench@us.ibm.com>
Move address display into a new function and display the scopeid as part
of the address in /proc/mounts.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: Fix oops on unaligned user access
avr32: Add support for Mediama RMTx add-on board for ATNGW100
avr32: Change Atmel ATNGW100 config to add choice of add-on board
Fix MIMC200 board LCD init
avr32: Fix clash in ATMEL_USART_ flags
avr32: remove obsolete hw_interrupt_type
avr32: Solves problem with inverted MCI detect pin on Merisc board
atmel-mci: Add support for inverted detect pin
Fix interaction with new generic header stuff as added by:
commit 6103ec56c6
Author: Arnd Bergmann <arnd@arndb.de>
Date: Wed May 13 22:56:27 2009 +0000
asm-generic: add generic ABI headers
The problem is that asm/signal.h has been made to include asm-generic/signal.h,
but the redundant stuff from asm/signal.h has not been discarded, leading to
multiple redefinitions.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next-i2c' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-ocores: Can add I2C devices to the bus
i2c-s3c2410: move to using platform idtable to match devices
i2c: OMAP3: Better noise suppression for fast/standard modes
i2c: OMAP2/3: Fix scll/sclh calculations
i2c: Blackfin TWI: implement I2C_FUNC_SMBUS_I2C_BLOCK functionality
i2c: Blackfin TWI: fix transfer errors with repeat start
i2c: Blackfin TWI: fix REPEAT START mode doesn't repeat
i2c: Blackfin TWI: make sure we don't end up with a CLKDIV=0
* 'docs-next' of git://git.lwn.net/linux-2.6:
Document the debugfs API
Documentation: Add "how to write a good patch summary" to SubmittingPatches
SubmittingPatches: fix typo
docs: Encourage better changelogs in the development process document
Document Reported-by in SubmittingPatches
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (35 commits)
hwrng: timeriomem - Fix potential oops (request_mem_region/__devinit)
crypto: api - Use formatting of module name
crypto: testmgr - Allow hash test vectors longer than a page
crypto: testmgr - Check all test vector lengths
crypto: hifn_795x - fix __dev{init,exit} markings
crypto: tcrypt - Do not exit on success in fips mode
crypto: compress - Return produced bytes in crypto_{,de}compress_{update,final}
hwrng: via_rng - Support VIA Nano hardware RNG on X86_64 builds
hwrng: via_rng - Support VIA Nano hardware RNG
hwrng: via_rng - The VIA Hardware RNG driver is for the CPU, not Chipset
crypto: testmgr - Skip algs not flagged fips_allowed in fips mode
crypto: testmgr - Mark algs allowed in fips mode
crypto: testmgr - Add ctr(aes) test vectors
crypto: testmgr - Dynamically allocate xbuf and axbuf
crypto: testmgr - Print self-test pass notices in fips mode
crypto: testmgr - Catch base cipher self-test failures in fips mode
crypto: testmgr - Add ansi_cprng test vectors
crypto: testmgr - Add infrastructure for ansi_cprng self-tests
crypto: testmgr - Add self-tests for rfc4309(ccm(aes))
crypto: testmgr - Handle AEAD test vectors expected to fail verification
...
drivers/net/cnic.c: In function ‘init_bnx2_cnic’:
drivers/net/cnic.c:2520: error: implicit declaration of function ‘__symbol_get’
drivers/net/cnic.c:2520: warning: assignment makes pointer from integer without a cast
make[1]: *** [drivers/net/cnic.o] Error 1
make: *** [drivers/net/cnic.o] Error 2
Caused by not including linux/module.h
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix cnic build for case of CONFIG_INET=n.
Fix cnic build for case of CONFIG_IPV6=m and CONFIG_CNIC=y.
Fixes these build errors:
cnic.c:(.text+0x236a1d): undefined reference to `ip_route_output_key'
cnic.c:(.text+0x15a8e8): undefined reference to `ip6_route_output'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The unaligned address exception handler (and others) does not scan the
fixup tables before oopsing. This is bad because it means passing a
badly aligned pointer from user space might crash the kernel.
Fix this by scanning the fixup tables in _exception(). This should
resolve the issue for unaligned addresses as well as other less common
exceptions that might be happening during a userspace access. The page
fault handler already does fixup processing.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
There is sometimes a need for the ocores driver to add devices to the
bus when installed.
i2c_register_board_info can not always be used, because the I2C devices
are not known at an early state, they could for instance be connected
on a I2C bus on a PCI device which has the Open Cores IP.
i2c_new_device can not be used in all cases either since the resulting
bus nummer might be unknown.
The solution is the pass a list of I2C devices in the platform data to
the Open Cores driver. This is useful for MFD drivers.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change to using platform id table to match either of the two supported
platform device names in the driver. This simplifies the driver init and
exit code
Note, log messages will now be prefixed with 's3c-i2c' instead of the
driver name, so output will be of the form of:
s3c-i2c s3c2440-i2c.0: slave address 0x10
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Use longer noise filter period for fast and standard mode. Based on an
earlier patch by Eero Nurkkala.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix scll/sclh calculations for HS and fast modes. Currently the driver
uses equal (roughly) low/high times which will result in too short
low time.
OMAP3430 TRM gives the following equations:
F/S: tLow = (scll + 7) * internal_clk
tHigh = (sclh + 5) * internal_clk
HS: tLow = (scll + 7) * fclk
tHigh = (sclh + 5) * fclk
Furthermore, the I2C specification sets the following minimum values
for HS tLow/tHigh for capacitive bus loads 100 pF (maximum speed 3400)
and 400 pF (maximum speed 1700):
speed tLow tHigh
3400 160 ns 60 ns
1700 320 ns 120 ns
and for F/S:
speed tLow tHigh
400 1300 ns 600 ns
100 4700 ns 4000 ns
By using duty cycles 33/66 (HS, F) and 50/50 (S) we stay above these
minimum values.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Some drivers need i2c_smbus_read_i2c_block_data() functionality, so add
support for it to the Blackfin I2C bus driver.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
[ben-linux@fluff.org: shortened subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We have a custom BF537 board with an I2C RTC (MAX DS3231) running
uclinux 2007R1 for some time. Recently during migration to 2008R1.5-RC3
we losted access to the RTC. The RTC driver calls 'i2c_transfer()' which
in turns calls 'bfin_twi_master_xfer()' in i2c-bfin-twi.c.
Compared with 2007R1, it looks like the 2008R1.5 version of i2c-bin-twi.c
has a new mode 'TWI_I2C-MODE_REPEAT' which corresponds to the Repeat Start
Condition described in the HRM. However, according to the HRM, at XMIT or
RECV interrupt and when the data count is 0, not only is the RESTART bit
supposed to be set, but MDIR must also be set if the next operation is a
receive sequence, and cleared if not. Currently there is no code that looks
at the I2C_M_RD bit in the flag from the next cur_msg and set/clear the MDIR
flag accordingly at the same time that the RSTART bit is set. Instead, MDIR
is set or cleared (by OR'ing with 0?) after the RESTART bit has been cleared
during handling of MCOMP interrupt.
It appears that this is causing our failure with reading the RTC, as a
quick patch to set/clear MDIR when RESTART is set seem to solve our problem.
Signed-off-by: Frank Shew <fshew@geometrics.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[ben-linux@fluff.org: shorted subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Avoid rewrite TWI MASTER_CTL reg when issue next message
In i2c repeat transfer mode, byte count of next message should be filled
into part of the TWI MASTER_CTL reg when interrupt MCOMP of last
message transfer is triggered. But, other bits in this reg should
not be touched.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[ben-linux@fluff.org: shorted subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make sure we don't end up with an invalid CLKDIV=0 in case someone
specifies 20kHz SCL or less (5 * 1024 / 20 = 0x100).
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[ben-linux@fluff.org: shortened subject line]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
...to consolidate some logic used in more than one place.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
show_options is always called with the namespace_sem held. Therefore we
don't need to worry about the vfsmount being NULL, or it vanishing while
the function is running. By the same token, there's no need to worry
about the superblock, tcon, smb or tcp sessions being NULL on entry.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Identation got messed up when merging the current_umask changes with
the generic ACL support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
Fix warnings about unitialized dquot variables by making sure
xfs_qm_vop_dqalloc touches it even when quotas are disabled.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/configfs:
configfs: Rework configfs_depend_item() locking and make lockdep happy
configfs: Silence lockdep on mkdir() and rmdir()
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (30 commits)
[S390] wire up sys_perf_counter_open
[S390] wire up sys_rt_tgsigqueueinfo
[S390] ftrace: add system call tracer support
[S390] ftrace: add function graph tracer support
[S390] ftrace: add function trace mcount test support
[S390] ftrace: add dynamic ftrace support
[S390] kprobes: use probe_kernel_write
[S390] maccess: arch specific probe_kernel_write() implementation
[S390] maccess: add weak attribute to probe_kernel_write
[S390] profile_tick called twice
[S390] dasd: forward internal errors to dasd_sleep_on caller
[S390] dasd: sync after async probe
[S390] dasd: check_characteristics cleanup
[S390] dasd: no High Performance FICON in 31-bit mode
[S390] dcssblk: revert devt conversion
[S390] qdio: fix access beyond ARRAY_SIZE of irq_ptr->{in,out}put_qs
[S390] vmalloc: add vmalloc kernel parameter support
[S390] uaccess: use might_fault() instead of might_sleep()
[S390] 3270: lock dependency fixes
[S390] 3270: do not register with tty_register_device
...
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (50 commits)
drm: include kernel list header file in hashtab header
drm: Export hash table functionality.
drm: Split out the mm declarations in a separate header. Add atomic operations.
drm/radeon: add support for RV790.
drm/radeon: add rv740 drm support.
drm_calloc_large: check right size, check integer overflow, use GFP_ZERO
drm: Eliminate magic I2C frobbing when reading EDID
drm/i915: duplicate desired mode for use by fbcon.
drm/via: vfree() no need checking before calling it
drm: Replace DRM_DEBUG with DRM_DEBUG_DRIVER in i915 driver
drm: Replace DRM_DEBUG with DRM_DEBUG_MODE in drm_mode
drm/i915: Replace DRM_DEBUG with DRM_DEBUG_KMS in intel_sdvo
drm/i915: replace DRM_DEBUG with DRM_DEBUG_KMS in intel_lvds
drm: add separate drm debugging levels
radeon: remove _DRM_DRIVER from the preadded sarea map
drm: don't associate _DRM_DRIVER maps with a master
drm: simplify kcalloc() call to kzalloc().
intelfb: fix spelling of "CLOCK"
drm: fix LOCK_TEST_WITH_RETURN macro
drm/i915: Hook connector to encoder during load detection (fixes tv/vga detect)
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: use more NOFS allocation
dlm: connect to nodes earlier
dlm: fix use count with multiple joins
dlm: Make name input parameter of {,dlm_}new_lockspace() const
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_counter: Start documenting HAVE_PERF_COUNTERS requirements
perf_counter: Add forward/backward attribute ABI compatibility
perf record: Explicity program a default counter
perf_counter: Remove PERF_TYPE_RAW special casing
perf_counter: PERF_TYPE_HW_CACHE is a hardware counter too
powerpc, perf_counter: Fix performance counter event types
perf_counter/x86: Add a quirk for Atom processors
perf_counter tools: Remove one L1-data alias
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (62 commits)
Blackfin: fix sparseirq/kstat_irqs fallout
Blackfin: fix unused warnings after nommu update
Blackfin: export the last exception cause via debugfs
Blackfin: fix length checking in kgdb_ebin2mem
Blackfin: kgdb: fix up error return values
Blackfin: push access_ok() L1 attribute down
Blackfin: punt duplicated search_exception_table() prototype
Blackfin: add missing access_ok() checks to user functions
Blackfin: convert early_printk EVT init to a loop
Blackfin: document the lsl variants of the L1 allocator
Blackfin: rename Blackfin relocs according to the toolchain
Blackfin: check SIC defines rather than variant names
Blackfin: add SSYNC to set_dma_sg() for descriptor fetching
Blackfin: convert SMP to only use generic time framework
Blackfin: bf548-ezkit/bf537-stamp: add resources for ADXL345/346
Blackfin: override default uClinux MTD addr/size
Blackfin: fix command line corruption with DEBUG_DOUBLEFAULT
Blackfin: fix handling of initial L1 reservation
Blackfin: merge sram init functions
Blackfin: drop unused reserve_pda() function
...
* 'for-linus' of git://linux-arm.org/linux-2.6:
kmemleak: Add more info to the MAINTAINERS entry
kmemleak: Remove the kmemleak.h include in drivers/char/vt.c
git commit 0a0c5168 "PM: Introduce functions for suspending and resuming
device interrupts" introduced some helper functions. However these
functions are only available for architectures which support
GENERIC_HARDIRQS.
Other architectures will see this build error:
drivers/built-in.o: In function `sysdev_suspend':
(.text+0x15138): undefined reference to `check_wakeup_irqs'
drivers/built-in.o: In function `device_power_up':
(.text+0x1cb66): undefined reference to `resume_device_irqs'
drivers/built-in.o: In function `device_power_down':
(.text+0x1cb92): undefined reference to `suspend_device_irqs'
To fix this add some empty inline functions for !GENERIC_HARDIRQS.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The *_nvs_* routines in swsusp.c make use of the io*map()
functions, which are only provided for HAS_IOMEM, thus
breaking compilation if HAS_IOMEM is not set. Fix this
by moving the *_nvs_* routines into hibernate_nvs.c, which
is only compiled if HAS_IOMEM is set.
[rjw: Change the name of the new file to hibernate_nvs.c, add the
license line to the header comment.]
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Change the name of kernel/power/disk.c to kernel/power/hibernate.c
in analogy with the file names introduced by the changes that
separated the suspend to RAM and standby funtionality from the
common PM functions.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
