Pull misc user access cleanups from Al Viro:
"The first pile is assorted getting rid of cargo-culted access_ok(),
cargo-culted set_fs() and field-by-field copyouts.
The same description applies to a lot of stuff in other branches -
this is just the stuff that didn't fit into a more specific topical
branch"
* 'work.misc-set_fs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Switch flock copyin/copyout primitives to copy_{from,to}_user()
fs/fcntl: return -ESRCH in f_setown when pid/pgid can't be found
fs/fcntl: f_setown, avoid undefined behaviour
fs/fcntl: f_setown, allow returning error
lpfc debugfs: get rid of pointless access_ok()
adb: get rid of pointless access_ok()
isdn: get rid of pointless access_ok()
compat statfs: switch to copy_to_user()
fs/locks: don't mess with the address limit in compat_fcntl64
nfsd_readlink(): switch to vfs_get_link()
drbd: ->sendpage() never needed set_fs()
fs/locks: pass kernel struct flock to fcntl_getlk/setlk
fs: locks: Fix some troubles at kernel-doc comments
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
The patch below updated xfs_dq_get_next_id() to use the XFS iext
lookup helpers to locate the next quota id rather than to seek for
data in the quota file. The updated code fails to correctly handle
the case where the quota inode might have contiguous chunks part of
the same extent. In this case, the start block offset is calculated
based on the next expected id but the extent lookup returns the same
start offset as for the previous chunk. This causes the returned id
to go backwards and livelocks the quota iteration. This problem is
reproduced intermittently by generic/232.
To handle this case, check whether the startoff from the extent
lookup is behind the startoff calculated from the next quota id. If
so, bump up got.br_startoff to the specific file offset that is
expected to hold the next dquot chunk.
Fixes: bda250dbaf ("xfs: rewrite xfs_dq_get_next_id using xfs_iext_lookup_extent")
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
- use memdup_user() instead of open-coded copies (Geliang Tang)
- fix record memory leak during initialization (Douglas Anderson)
- avoid confused compressed record warning (Ankit Kumar)
- prepopulate record timestamp and remove redundant logic from backends
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Kees Cook <kees@outflux.net>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=VRl5
-----END PGP SIGNATURE-----
Merge tag 'pstore-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore updates from Kees Cook:
"Various fixes and tweaks for the pstore subsystem.
Highlights:
- use memdup_user() instead of open-coded copies (Geliang Tang)
- fix record memory leak during initialization (Douglas Anderson)
- avoid confused compressed record warning (Ankit Kumar)
- prepopulate record timestamp and remove redundant logic from
backends"
* tag 'pstore-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
powerpc/nvram: use memdup_user
pstore: use memdup_user
pstore: Fix format string to use %u for record id
pstore: Populate pstore record->time field
pstore: Create common record initializer
efi-pstore: Refactor erase routine
pstore: Avoid potential infinite loop
pstore: Fix leaked pstore_record in pstore_get_backend_records()
pstore: Don't warn if data is uncompressed and type is not PSTORE_TYPE_DMESG
Pull security layer updates from James Morris:
- a major update for AppArmor. From JJ:
* several bug fixes and cleanups
* the patch to add symlink support to securityfs that was floated
on the list earlier and the apparmorfs changes that make use of
securityfs symlinks
* it introduces the domain labeling base code that Ubuntu has been
carrying for several years, with several cleanups applied. And it
converts the current mediation over to using the domain labeling
base, which brings domain stacking support with it. This finally
will bring the base upstream code in line with Ubuntu and provide
a base to upstream the new feature work that Ubuntu carries.
* This does _not_ contain any of the newer apparmor mediation
features/controls (mount, signals, network, keys, ...) that
Ubuntu is currently carrying, all of which will be RFC'd on top
of this.
- Notable also is the Infiniband work in SELinux, and the new file:map
permission. From Paul:
"While we're down to 21 patches for v4.13 (it was 31 for v4.12),
the diffstat jumps up tremendously with over 2k of line changes.
Almost all of these changes are the SELinux/IB work done by
Daniel Jurgens; some other noteworthy changes include a NFS v4.2
labeling fix, a new file:map permission, and reporting of policy
capabilities on policy load"
There's also now genfscon labeling support for tracefs, which was
lost in v4.1 with the separation from debugfs.
- Smack incorporates a safer socket check in file_receive, and adds a
cap_capable call in privilege check.
- TPM as usual has a bunch of fixes and enhancements.
- Multiple calls to security_add_hooks() can now be made for the same
LSM, to allow LSMs to have hook declarations across multiple files.
- IMA now supports different "ima_appraise=" modes (eg. log, fix) from
the boot command line.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (126 commits)
apparmor: put back designators in struct initialisers
seccomp: Switch from atomic_t to recount_t
seccomp: Adjust selftests to avoid double-join
seccomp: Clean up core dump logic
IMA: update IMA policy documentation to include pcr= option
ima: Log the same audit cause whenever a file has no signature
ima: Simplify policy_func_show.
integrity: Small code improvements
ima: fix get_binary_runtime_size()
ima: use ima_parse_buf() to parse template data
ima: use ima_parse_buf() to parse measurements headers
ima: introduce ima_parse_buf()
ima: Add cgroups2 to the defaults list
ima: use memdup_user_nul
ima: fix up #endif comments
IMA: Correct Kconfig dependencies for hash selection
ima: define is_ima_appraise_enabled()
ima: define Kconfig IMA_APPRAISE_BOOTPARAM option
ima: define a set of appraisal rules requiring file signatures
ima: extend the "ima_policy" boot command line to support multiple policies
...
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
5259 1344 8 6611 19d3 fs/gfs2/sys.o
File size After adding 'const':
text data bss dec hex filename
5371 1216 8 6595 19c3 fs/gfs2/sys.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
On failure, keep the inode glock across the final iput of the new inode
so that gfs2_evict_inode doesn't have to re-acquire the glock. That
way, gfs2_evict_inode won't need to revalidate the block type.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
This patch adds a standardized queueing mechanism for glock work
with spin_lock protection to prevent races.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Put all remaining accesses to gl->gl_object under the
gl->gl_lockref.lock spinlock to prevent races.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
So far, gfs2_evict_inode clears gl->gl_object and then flushes the glock
work queue to make sure that inode glops which dereference gl->gl_object
have finished running before the inode is destroyed. However, flushing
the work queue may do more work than needed, and in particular, it may
call into DLM, which we want to avoid here. Use a bit lock
(GIF_GLOP_PENDING) to synchronize between the inode glops and
gfs2_evict_inode instead to get rid of the flushing.
In addition, flush the work queues of existing glocks before reusing
them for new inodes to get those glocks into a known state: the glock
state engine currently doesn't handle glock re-appropriation correctly.
(We may be able to fix the glock state engine instead later.)
Based on a patch by Steven Whitehouse <swhiteho@redhat.com>.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
KMSAN (KernelMemorySanitizer, a new error detection tool) reports the
use of uninitialized memory in ext4_update_bh_state():
==================================================================
BUG: KMSAN: use of unitialized memory
CPU: 3 PID: 1 Comm: swapper/0 Tainted: G B 4.8.0-rc6+ #597
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs
01/01/2011
0000000000000282 ffff88003cc96f68 ffffffff81f30856 0000003000000008
ffff88003cc96f78 0000000000000096 ffffffff8169742a ffff88003cc96ff8
ffffffff812fc1fc 0000000000000008 ffff88003a1980e8 0000000100000000
Call Trace:
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffff81f30856>] dump_stack+0xa6/0xc0 lib/dump_stack.c:51
[<ffffffff812fc1fc>] kmsan_report+0x1ec/0x300 mm/kmsan/kmsan.c:?
[<ffffffff812fc33b>] __msan_warning+0x2b/0x40 ??:?
[< inline >] ext4_update_bh_state fs/ext4/inode.c:727
[<ffffffff8169742a>] _ext4_get_block+0x6ca/0x8a0 fs/ext4/inode.c:759
[<ffffffff81696d4c>] ext4_get_block+0x8c/0xa0 fs/ext4/inode.c:769
[<ffffffff814a2d36>] generic_block_bmap+0x246/0x2b0 fs/buffer.c:2991
[<ffffffff816ca30e>] ext4_bmap+0x5ee/0x660 fs/ext4/inode.c:3177
...
origin description: ----tmp@generic_block_bmap
==================================================================
(the line numbers are relative to 4.8-rc6, but the bug persists
upstream)
The local |tmp| is created in generic_block_bmap() and then passed into
ext4_bmap() => ext4_get_block() => _ext4_get_block() =>
ext4_update_bh_state(). Along the way tmp.b_page is never initialized
before ext4_update_bh_state() checks its value.
[ Use the approach suggested by Kees Cook of initializing the whole bh
structure.]
Signed-off-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
index entry should live only as long as there are upper or lower
hardlinks.
Cleanup orphan index entries on mount and when dropping the last
overlay inode nlink.
When about to cleanup or link up to orphan index and the index inode
nlink > 1, admit that something went wrong and adjust overlay nlink
to index inode nlink - 1 to prevent it from dropping below zero.
This could happen when adding lower hardlinks underneath a mounted
overlay and then trying to unlink them.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
With inodes index enabled, an overlay inode nlink counts the union of upper
and non-covered lower hardlinks. During the lifetime of a non-pure upper
inode, the following nlink modifying operations can happen:
1. Lower hardlink copy up
2. Upper hardlink created, unlinked or renamed over
3. Lower hardlink whiteout or renamed over
For the first, copy up case, the union nlink does not change, whether the
operation succeeds or fails, but the upper inode nlink may change.
Therefore, before copy up, we store the union nlink value relative to the
lower inode nlink in the index inode xattr trusted.overlay.nlink.
For the second, upper hardlink case, the union nlink should be incremented
or decremented IFF the operation succeeds, aligned with nlink change of the
upper inode. Therefore, before link/unlink/rename, we store the union nlink
value relative to the upper inode nlink in the index inode.
For the last, lower cover up case, we simplify things by preceding the
whiteout or cover up with copy up. This makes sure that there is an index
upper inode where the nlink xattr can be stored before the copied up upper
entry is unlink.
Return the overlay inode nlinks for indexed upper inodes on stat(2).
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Implement a copy up method for non-dir objects using index dir to
prevent breaking lower hardlinks on copy up.
This method requires that the inodes index dir feature was enabled and
that all underlying fs support file handle encoding/decoding.
On the first lower hardlink copy up, upper file is created in index dir,
named after the hex representation of the lower origin inode file handle.
On the second lower hardlink copy up, upper file is found in index dir,
by the same lower handle key.
On either case, the upper indexed inode is then linked to the copy up
upper path.
The index entry remains linked for future lower hardlink copy up and for
lower to upper inode map, that is needed for exporting overlayfs to NFS.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Move ovl_copy_up_start()/ovl_copy_up_end() out so that it's used for both
tempfile and workdir copy ups.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
For rename, we need to ensure that an upper alias exists for hard links
before attempting the operation. Introduce a flag in ovl_entry to track
the state of the upper alias.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Factor out helper for copying lower inode data and metadata to temp
upper inode, that is common to copy up using O_TMPFILE and workdir.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
On copy up of regular file using an O_TMPFILE, lock upper dir only
before linking the tempfile in place.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Bad index entries are entries whose name does not match the
origin file handle stored in trusted.overlay.origin xattr.
Bad index entries could be a result of a system power off in
the middle of copy up.
Stale index entries are entries whose origin file handle is
stale. Stale index entries could be a result of copying layers
or removing lower entries while the overlay is not mounted.
The case of copying layers should be detected earlier by the
verification of upper root dir origin and index dir origin.
Both bad and stale index entries are detected and removed
on mount.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
When inodes index feature is enabled, lookup in indexdir for the index
entry of lower real inode or copy up origin inode. The index entry name
is the hex representation of the lower inode file handle.
If the index dentry in negative, then either no lower aliases have been
copied up yet, or aliases have been copied up in older kernels and are
not indexed.
If the index dentry for a copy up origin inode is positive, but points
to an inode different than the upper inode, then either the upper inode
has been copied up and not indexed or it was indexed, but since then
index dir was cleared. Either way, that index cannot be used to indentify
the overlay inode.
If a positive dentry that matches the upper inode was found, then it is
safe to use the copy up origin st_ino for upper hardlinks, because all
indexed upper hardlinks are represented by the same overlay inode as the
copy up origin.
Set the INDEX type flag on an indexed upper dentry. A non-upper dentry
may also have a positive index from copy up of another lower hardlink.
This situation will be handled by following patches.
Index lookup is going to be used to prevent breaking hardlinks on copy up.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
An index dir contains persistent hardlinks to files in upper dir.
Therefore, we must never mount an existing index dir with a differnt
upper dir.
Store the upper root dir file handle in index dir inode when index
dir is created and verify the file handle before using an existing
index dir on mount.
Add an 'is_upper' flag to the overlay file handle encoding and set it
when encoding the upper root file handle. This is not critical for index
dir verification, but it is good practice towards a standard overlayfs
file handle format for NFS export.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
When inodes index feature is enabled, verify that the file handle stored
in upper root dir matches the lower root dir or fail to mount.
If upper root dir has no stored file handle, encode and store the lower
root dir file handle in overlay.origin xattr.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Create the index dir on mount. The index dir will contain hardlinks to
upper inodes, named after the hex representation of their origin lower
inodes.
The index dir is going to be used to prevent breaking lower hardlinks
on copy up and to implement overlayfs NFS export.
Because the feature is not fully backward compat, enabling the feature
is opt-in by config/module/mount option.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Pass in the subdir name to create and specify if subdir is persistent
or if it should be cleaned up on every mount.
Move fallback to readonly mount on failure to create dir and print of error
message into the helper.
This function is going to be used for creating the persistent 'index' dir
under workbasedir.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
For the case of all layers not on the same fs, try to decode the copy up
origin file handle on any of the lower layers.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Bad things can happen if several concurrent overlay mounts try to
use the same upperdir/workdir path.
Try to get the 'inuse' advisory lock on upperdir and workdir.
Fail mount if another overlay mount instance or another user
holds the 'inuse' lock on these directories.
Note that this provides no protection for concurrent overlay
mount that use overlapping (i.e. descendant) upper/work dirs.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Added an i_state flag I_INUSE and helpers to set/clear/test the bit.
The 'inuse' lock is an 'advisory' inode lock, that can be used to extend
exclusive create protection beyond parent->i_mutex lock among cooperating
users.
This is going to be used by overlayfs to get exclusive ownership on upper
and work dirs among overlayfs mounts.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Use the new ovl_inode mutex to synchonize concurrent copy up
instead of the super block copy up workqueue.
Moving the synchronization object from the overlay dentry to
the overlay inode is needed for synchonizing concurrent copy up
of lower hardlinks to the same upper inode.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
When checking for consistency in directory operations (unlink, rename,
etc.) match inodes not dentries.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
We need some more space to store overlay inode data in memory,
so allocate overlay inodes from a slab of struct ovl_inode.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
This patch fixes an overlay inode nlink leak in the case where
ovl_rename() renames over a non-dir.
This is not so critical, because overlay inode doesn't rely on
nlink dropping to zero for inode deletion.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Both in memory or on disk, generic filesystems record i_blocks with
512bytes sized sector count, also VFS sub module such as disk quota
follows this rule, but f2fs records it with 4096bytes sized block
count, this difference leads to that once we use dquota's function
which inc/dec iblocks, it will make i_blocks of f2fs being inconsistent
between in memory and on disk.
In order to resolve this issue, this patch changes to make in-memory
i_blocks of f2fs recording sector count instead of block count,
meanwhile leaving on-disk i_blocks recording block count.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Don't set CP_TRIMMED_FLAG for non-zoned block device or discard
unsupported device, it can avoid to trigger unneeded checkpoint for
that kind of device.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Currently, filesystems allow truncate(2) on an encrypted file without
the encryption key. However, it's impossible to correctly handle the
case where the size being truncated to is not a multiple of the
filesystem block size, because that would require decrypting the final
block, zeroing the part beyond i_size, then encrypting the block.
As other modifications to encrypted file contents are prohibited without
the key, just prohibit truncate(2) as well, making it fail with ENOKEY.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Codes related to sysfs and procfs are dispersive and mixed with sb
related codes, but actually these codes are independent from others,
so split them from super.c, and reorgnize and manger them in sysfs.c.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch fixes incorrect error number in error path of fill_super.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
If fault injection functionality is enabled, show additional injection
rate in ->show_options.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
err must be set to -ENOMEM, otherwise we return 0.
Fixes: a912b54d3a ("f2fs: split bio cache")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
It is better to use variable name "inline_dentry" instead of "dentry_blk"
when data type is "struct f2fs_inline_dentry". This patch has no functional
changes, just to make code more readable especially when call the function
make_dentry_ptr_inline() and f2fs_convert_inline_dir().
Signed-off-by: Tiezhu Yang <kernelpatch@126.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
With fault_injection option, generic/361 of fstests will complain us
with below message:
Call Trace:
get_node_page+0x12/0x20 [f2fs]
f2fs_iget+0x92/0x7d0 [f2fs]
f2fs_fill_super+0x10fb/0x15e0 [f2fs]
mount_bdev+0x184/0x1c0
f2fs_mount+0x15/0x20 [f2fs]
mount_fs+0x39/0x150
vfs_kern_mount+0x67/0x110
do_mount+0x1bb/0xc70
SyS_mount+0x83/0xd0
do_syscall_64+0x6e/0x160
entry_SYSCALL64_slow_path+0x25/0x25
Since mkfs loop device in f2fs partition can be failed silently due to
checkpoint error injection, so root inode page can be corrupted, in order
to avoid needless panic, in get_node_page, it's better to leave message
and return error to caller, and let fsck repaire it later.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
We will never persist newly allocated nat entries during checkpoint(), so
we don't need to track such nat entries in nat dirty list in order to
avoid:
- more latency during traversing dirty list;
- sorting nat sets incorrectly due to recording wrong entry_cnt in nat
entry set.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Recently, discard related codes have changed a lot, so add f2fs_bug_on to
detect potential bug.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Currently in F2FS, page faults and operations that truncate the pagecahe
or data blocks, are completely unsynchronized. This can result in page
fault faulting in a page into a range that we are changing after
truncating, and thus we can end up with a page mapped to disk blocks that
will be shortly freed. Filesystem corruption will shortly follow.
This patch fixes the problem by creating new rw semaphore i_mmap_sem in
f2fs_inode_info and grab it for functions removing blocks from extent tree
and for read over page faults. The mechanism is similar to that in ext4.
Signed-off-by: Qiuyang Sun <sunqiuyang@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The index of segment which the next nat block is in has only one different
bit than the current one, so to get the next nat address, we can simply
alter that one bit.
Signed-off-by: Fan Li <fanofcode.li@samsung.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Make sure number of entires doesn't exceed max journal size.
Cc: stable@vger.kernel.org
Signed-off-by: Jin Qian <jinqian@android.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Mount fs with option noflush_merge, boot failed for illegal address
fcc in function f2fs_issue_flush:
if (!test_opt(sbi, FLUSH_MERGE)) {
ret = submit_flush_wait(sbi);
atomic_inc(&fcc->issued_flush); -> Here, fcc illegal
return ret;
}
Signed-off-by: Yunlei He <heyunlei@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
It's not necessary to specify 'int' casting for PTR_ERR.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
For example,
f2fs_create
- new_node_page is failed
- handle_failed_inode
- skip to add it into orphan list, since ni.blk_addr == NULL_ADDR
: set_inode_flag(inode, FI_FREE_NID)
f2fs_evict_inode
- EIO due to fault injection
- f2fs_bug_on() is triggered
So, we don't need to call f2fs_bug_on in this case.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
clear_prefree_segments() issues small discards after discarding full
segments. These small discards may not be section aligned, so not zone
aligned on a zoned block device, causing __f2fs_iissue_discard_zone() to fail.
Fix this by not issuing small discards for a volume mounted with the BLKZONED
feature enabled.
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
around. Highlights include:
- Conversion of a bunch of security documentation into RST
- The conversion of the remaining DocBook templates by The Amazing
Mauro Machine. We can now drop the entire DocBook build chain.
- The usual collection of fixes and minor updates.
-----BEGIN PGP SIGNATURE-----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=cVjZ
-----END PGP SIGNATURE-----
Merge tag 'docs-4.13' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"There has been a fair amount of activity in the docs tree this time
around. Highlights include:
- Conversion of a bunch of security documentation into RST
- The conversion of the remaining DocBook templates by The Amazing
Mauro Machine. We can now drop the entire DocBook build chain.
- The usual collection of fixes and minor updates"
* tag 'docs-4.13' of git://git.lwn.net/linux: (90 commits)
scripts/kernel-doc: handle DECLARE_HASHTABLE
Documentation: atomic_ops.txt is core-api/atomic_ops.rst
Docs: clean up some DocBook loose ends
Make the main documentation title less Geocities
Docs: Use kernel-figure in vidioc-g-selection.rst
Docs: fix table problems in ras.rst
Docs: Fix breakage with Sphinx 1.5 and upper
Docs: Include the Latex "ifthen" package
doc/kokr/howto: Only send regression fixes after -rc1
docs-rst: fix broken links to dynamic-debug-howto in kernel-parameters
doc: Document suitability of IBM Verse for kernel development
Doc: fix a markup error in coding-style.rst
docs: driver-api: i2c: remove some outdated information
Documentation: DMA API: fix a typo in a function name
Docs: Insert missing space to separate link from text
doc/ko_KR/memory-barriers: Update control-dependencies example
Documentation, kbuild: fix typo "minimun" -> "minimum"
docs: Fix some formatting issues in request-key.rst
doc: ReSTify keys-trusted-encrypted.txt
doc: ReSTify keys-request-key.txt
...
ext4_inode_info->i_data is the storage area for 4 types of data:
a) Extents data
b) Inline data
c) Block map
d) Fast symlink data (symlink length < 60)
Extents data case is positively identified by EXT4_INODE_EXTENTS flag.
Inline data case is also obvious because of EXT4_INODE_INLINE_DATA
flag.
Distinguishing c) and d) however requires additional logic. This
currently relies on i_blocks count. After subtracting external xattr
block from i_blocks, if it is greater than 0 then we know that some
data blocks exist, so there must be a block map.
This logic got broken after ea_inode feature was added. That feature
charges the data blocks of external xattr inodes to the referencing
inode and so adds them to the i_blocks. To fix this, we could subtract
ea_inode blocks by iterating through all xattr entries and then check
whether remaining i_blocks count is zero. Besides being complicated,
this won't change the fact that the current way of distinguishing
between c) and d) is fragile.
The alternative solution is to test whether i_size is less than 60 to
determine fast symlink case. ext4_symlink() uses the same test to decide
whether to store the symlink in i_data. There is one caveat to address
before this can work though.
If an inode's i_nlink is zero during eviction, its i_size is set to
zero and its data is truncated. If system crashes before inode is removed
from the orphan list, next boot orphan cleanup may find the inode with
zero i_size. So, a symlink that had its data stored in a block may now
appear to be a fast symlink. The solution used in this patch is to treat
i_size = 0 as a non-fast symlink case. A zero sized symlink is not legal
so the only time this can happen is the mentioned scenario. This is also
logically correct because a i_size = 0 symlink has no data stored in
i_data.
Suggested-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Here is the large tty/serial patchset for 4.13-rc1.
A lot of tty and serial driver updates are in here, along with some
fixups for some __get/put_user usages that were reported. Nothing huge,
just lots of development by a number of different developers, full
details in the shortlog.
All of these have been in linux-next for a while. There will be a merge
issue with the arm-soc tree in the include/linux/platform_data/atmel.h
file. Stephen has sent out a fixup for it, so it shouldn't be that
difficult to merge.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpZ9w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylkTgCfV2HhbxIph/aEL1nJmwW64oCXFrMAoK59ZH65
tBZIosv0d91K1A+mObBT
=adPL
-----END PGP SIGNATURE-----
Merge tag 'tty-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the large tty/serial patchset for 4.13-rc1.
A lot of tty and serial driver updates are in here, along with some
fixups for some __get/put_user usages that were reported. Nothing
huge, just lots of development by a number of different developers,
full details in the shortlog.
All of these have been in linux-next for a while"
* tag 'tty-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (71 commits)
tty: serial: lpuart: add a more accurate baud rate calculation method
tty: serial: lpuart: add earlycon support for imx7ulp
tty: serial: lpuart: add imx7ulp support
dt-bindings: serial: fsl-lpuart: add i.MX7ULP support
tty: serial: lpuart: add little endian 32 bit register support
tty: serial: lpuart: refactor lpuart32_{read|write} prototype
tty: serial: lpuart: introduce lpuart_soc_data to represent SoC property
serial: imx-serial - move DMA buffer configuration to DT
serial: imx: Enable RTSD only when needed
serial: imx: Remove unused members from imx_port struct
serial: 8250: 8250_omap: Fix race b/w dma completion and RX timeout
serial: 8250: Fix THRE flag usage for CAP_MINI
tty/serial: meson_uart: update to stable bindings
dt-bindings: serial: Add bindings for the Amlogic Meson UARTs
serial: Delete dead code for CIR serial ports
serial: sirf: make of_device_ids const
serial/mpsc: switch to dma_alloc_attrs
tty: serial: Add Actions Semi Owl UART earlycon
dt-bindings: serial: Document Actions Semi Owl UARTs
tty/serial: atmel: make the driver DT only
...
- introduce the new uuid_t/guid_t types that are going to replace
the somewhat confusing uuid_be/uuid_le types and make the terminology
fit the various specs, as well as the userspace libuuid library.
(me, based on a previous version from Amir)
- consolidated generic uuid/guid helper functions lifted from XFS
and libnvdimm (Amir and me)
- conversions to the new types and helpers (Amir, Andy and me)
-----BEGIN PGP SIGNATURE-----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=J/4P
-----END PGP SIGNATURE-----
Merge tag 'uuid-for-4.13' of git://git.infradead.org/users/hch/uuid into overlayfs-next
UUID/GUID updates:
- introduce the new uuid_t/guid_t types that are going to replace
the somewhat confusing uuid_be/uuid_le types and make the terminology
fit the various specs, as well as the userspace libuuid library.
(me, based on a previous version from Amir)
- consolidated generic uuid/guid helper functions lifted from XFS
and libnvdimm (Amir and me)
- conversions to the new types and helpers (Amir, Andy and me)
on MMU targets EFAULT is possible here. Make both return 0 or error,
passing what used to be the return value of flat_get_addr_from_rp()
by reference.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle were:
- Add the SYSTEM_SCHEDULING bootup state to move various scheduler
debug checks earlier into the bootup. This turns silent and
sporadically deadly bugs into nice, deterministic splats. Fix some
of the splats that triggered. (Thomas Gleixner)
- A round of restructuring and refactoring of the load-balancing and
topology code (Peter Zijlstra)
- Another round of consolidating ~20 of incremental scheduler code
history: this time in terms of wait-queue nomenclature. (I didn't
get much feedback on these renaming patches, and we can still
easily change any names I might have misplaced, so if anyone hates
a new name, please holler and I'll fix it.) (Ingo Molnar)
- sched/numa improvements, fixes and updates (Rik van Riel)
- Another round of x86/tsc scheduler clock code improvements, in hope
of making it more robust (Peter Zijlstra)
- Improve NOHZ behavior (Frederic Weisbecker)
- Deadline scheduler improvements and fixes (Luca Abeni, Daniel
Bristot de Oliveira)
- Simplify and optimize the topology setup code (Lauro Ramos
Venancio)
- Debloat and decouple scheduler code some more (Nicolas Pitre)
- Simplify code by making better use of llist primitives (Byungchul
Park)
- ... plus other fixes and improvements"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (103 commits)
sched/cputime: Refactor the cputime_adjust() code
sched/debug: Expose the number of RT/DL tasks that can migrate
sched/numa: Hide numa_wake_affine() from UP build
sched/fair: Remove effective_load()
sched/numa: Implement NUMA node level wake_affine()
sched/fair: Simplify wake_affine() for the single socket case
sched/numa: Override part of migrate_degrades_locality() when idle balancing
sched/rt: Move RT related code from sched/core.c to sched/rt.c
sched/deadline: Move DL related code from sched/core.c to sched/deadline.c
sched/cpuset: Only offer CONFIG_CPUSETS if SMP is enabled
sched/fair: Spare idle load balancing on nohz_full CPUs
nohz: Move idle balancer registration to the idle path
sched/loadavg: Generalize "_idle" naming to "_nohz"
sched/core: Drop the unused try_get_task_struct() helper function
sched/fair: WARN() and refuse to set buddy when !se->on_rq
sched/debug: Fix SCHED_WARN_ON() to return a value on !CONFIG_SCHED_DEBUG as well
sched/wait: Disambiguate wq_entry->task_list and wq_head->task_list naming
sched/wait: Move bit_wait_table[] and related functionality from sched/core.c to sched/wait_bit.c
sched/wait: Split out the wait_bit*() APIs from <linux/wait.h> into <linux/wait_bit.h>
sched/wait: Re-adjust macro line continuation backslashes in <linux/wait.h>
...
Pull core block/IO updates from Jens Axboe:
"This is the main pull request for the block layer for 4.13. Not a huge
round in terms of features, but there's a lot of churn related to some
core cleanups.
Note this depends on the UUID tree pull request, that Christoph
already sent out.
This pull request contains:
- A series from Christoph, unifying the error/stats codes in the
block layer. We now use blk_status_t everywhere, instead of using
different schemes for different places.
- Also from Christoph, some cleanups around request allocation and IO
scheduler interactions in blk-mq.
- And yet another series from Christoph, cleaning up how we handle
and do bounce buffering in the block layer.
- A blk-mq debugfs series from Bart, further improving on the support
we have for exporting internal information to aid debugging IO
hangs or stalls.
- Also from Bart, a series that cleans up the request initialization
differences across types of devices.
- A series from Goldwyn Rodrigues, allowing the block layer to return
failure if we will block and the user asked for non-blocking.
- Patch from Hannes for supporting setting loop devices block size to
that of the underlying device.
- Two series of patches from Javier, fixing various issues with
lightnvm, particular around pblk.
- A series from me, adding support for write hints. This comes with
NVMe support as well, so applications can help guide data placement
on flash to improve performance, latencies, and write
amplification.
- A series from Ming, improving and hardening blk-mq support for
stopping/starting and quiescing hardware queues.
- Two pull requests for NVMe updates. Nothing major on the feature
side, but lots of cleanups and bug fixes. From the usual crew.
- A series from Neil Brown, greatly improving the bio rescue set
support. Most notably, this kills the bio rescue work queues, if we
don't really need them.
- Lots of other little bug fixes that are all over the place"
* 'for-4.13/block' of git://git.kernel.dk/linux-block: (217 commits)
lightnvm: pblk: set line bitmap check under debug
lightnvm: pblk: verify that cache read is still valid
lightnvm: pblk: add initialization check
lightnvm: pblk: remove target using async. I/Os
lightnvm: pblk: use vmalloc for GC data buffer
lightnvm: pblk: use right metadata buffer for recovery
lightnvm: pblk: schedule if data is not ready
lightnvm: pblk: remove unused return variable
lightnvm: pblk: fix double-free on pblk init
lightnvm: pblk: fix bad le64 assignations
nvme: Makefile: remove dead build rule
blk-mq: map all HWQ also in hyperthreaded system
nvmet-rdma: register ib_client to not deadlock in device removal
nvme_fc: fix error recovery on link down.
nvmet_fc: fix crashes on bad opcodes
nvme_fc: Fix crash when nvme controller connection fails.
nvme_fc: replace ioabort msleep loop with completion
nvme_fc: fix double calls to nvme_cleanup_cmd()
nvme-fabrics: verify that a controller returns the correct NQN
nvme: simplify nvme_dev_attrs_are_visible
...
- introduce the new uuid_t/guid_t types that are going to replace
the somewhat confusing uuid_be/uuid_le types and make the terminology
fit the various specs, as well as the userspace libuuid library.
(me, based on a previous version from Amir)
- consolidated generic uuid/guid helper functions lifted from XFS
and libnvdimm (Amir and me)
- conversions to the new types and helpers (Amir, Andy and me)
-----BEGIN PGP SIGNATURE-----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=J/4P
-----END PGP SIGNATURE-----
Merge tag 'uuid-for-4.13' of git://git.infradead.org/users/hch/uuid
Pull uuid subsystem from Christoph Hellwig:
"This is the new uuid subsystem, in which Amir, Andy and I have started
consolidating our uuid/guid helpers and improving the types used for
them. Note that various other subsystems have pulled in this tree, so
I'd like it to go in early.
UUID/GUID summary:
- introduce the new uuid_t/guid_t types that are going to replace the
somewhat confusing uuid_be/uuid_le types and make the terminology
fit the various specs, as well as the userspace libuuid library.
(me, based on a previous version from Amir)
- consolidated generic uuid/guid helper functions lifted from XFS and
libnvdimm (Amir and me)
- conversions to the new types and helpers (Amir, Andy and me)"
* tag 'uuid-for-4.13' of git://git.infradead.org/users/hch/uuid: (34 commits)
ACPI: hns_dsaf_acpi_dsm_guid can be static
mmc: sdhci-pci: make guid intel_dsm_guid static
uuid: Take const on input of uuid_is_null() and guid_is_null()
thermal: int340x_thermal: fix compile after the UUID API switch
thermal: int340x_thermal: Switch to use new generic UUID API
acpi: always include uuid.h
ACPI: Switch to use generic guid_t in acpi_evaluate_dsm()
ACPI / extlog: Switch to use new generic UUID API
ACPI / bus: Switch to use new generic UUID API
ACPI / APEI: Switch to use new generic UUID API
acpi, nfit: Switch to use new generic UUID API
MAINTAINERS: add uuid entry
tmpfs: generate random sb->s_uuid
scsi_debug: switch to uuid_t
nvme: switch to uuid_t
sysctl: switch to use uuid_t
partitions/ldm: switch to use uuid_t
overlayfs: use uuid_t instead of uuid_be
fs: switch ->s_uuid to uuid_t
ima/policy: switch to use uuid_t
...
Switch to the iomap_seek_hole and iomap_seek_data helpers for
implementing lseek SEEK_HOLE / SEEK_DATA, and remove all the
code that isn't needed any more.
Based on patches from Andreas Gruenbacher <agruenba@redhat.com>.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Filesystems can use this for implementing lseek SEEK_HOLE / SEEK_DATA
support via iomap.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
[hch: split functions, coding style cleanups]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Both ext4 and xfs implement seeking for the next hole or piece of data
in unwritten extents by scanning the page cache, and both versions share
the same bug when iterating the buffers of a page: the start offset into
the page isn't taken into account, so when a page fits more than two
filesystem blocks, things will go wrong. For example, on a filesystem
with a block size of 1k, the following command will fail:
xfs_io -f -c "falloc 0 4k" \
-c "pwrite 1k 1k" \
-c "pwrite 3k 1k" \
-c "seek -a -r 0" foo
In this example, neither lseek(fd, 1024, SEEK_HOLE) nor lseek(fd, 2048,
SEEK_DATA) will return the correct result.
Introduce a generic vfs helper for seeking in the page cache that gets
this right. The next commits will replace the filesystem specific
implementations.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
[hch: dropped the export]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
We were missing a capability flag for SMB3.1.1
Signed-off-by: Steve French <steve.french@primarydata.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
This goes straight to a single lookup in the extent list and avoids a
roundtrip through two layers that don't add any value for the simple
quoata file that just has data or holes and no page cache, delayed
allocation, unwritten extent or COW fork (which btw, doesn't seem to
be handled by the existing SEEK HOLE/DATA code).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
While adding error injection into IO completion, I notice the lack of
initialization check in xfs_errortag_test(), make the error injection
mechanism unable to be used there.
IO completion is executed a few times before the error injection
mechanism is initialized, so to be safer, make xfs_errortag_test() check
if the errortag is properly initialized.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
This marks many critical kernel structures for randomization. These are
structures that have been targeted in the past in security exploits, or
contain functions pointers, pointers to function pointer tables, lists,
workqueues, ref-counters, credentials, permissions, or are otherwise
sensitive. This initial list was extracted from Brad Spengler/PaX Team's
code in the last public patch of grsecurity/PaX based on my understanding
of the code. Changes or omissions from the original code are mine and
don't reflect the original grsecurity/PaX code.
Left out of this list is task_struct, which requires special handling
and will be covered in a subsequent patch.
Signed-off-by: Kees Cook <keescook@chromium.org>
Pull overlayfs fixes from Miklos Szeredi:
"Fix two bugs in copy-up code. One introduced in 4.11 and one in
4.12-rc"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: don't set origin on broken lower hardlink
ovl: copy-up: don't unlock between lookup and link
Usage of these apis and their compat versions makes
the syscalls: timerfd_settime and timerfd_gettime and
their compat implementations simpler.
This patch also serves as a preparatory patch for changing
syscalls to use new time_t data types to support the
y2038 effort by isolating the processing of user pointers
through these apis.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Emergency remount (sysrq-u) sets MS_RDONLY to the superblock but doesn't set
MNT_READONLY to the mount point.
Once calculate_f_flags() only check for the mount point read only state,
when setting kstatfs flags, after an emergency remount, statfs does not
report the filesystem as read-only, even though it is.
Enable flags_by_sb() to also check for superblock read only state, so the
kstatfs and consequently statfs can properly show the read-only state of
the filesystem.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
in_lookup_hashtable was introduced in commit 94bdd655ca ("parallel
lookups machinery, part 3") and never initialized but since it is in
the data it is all zeros. But we need this for -RT.
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This function compiles to 1402 bytes of machine code.
It has 2 callsites, and also a not-inlined copy gets created by compiler
anyway since its address gets passed as a parameter to block_truncate_page().
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Al Viro <viro@zeniv.linux.org.uk>
CC: linux-fsdevel@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Checking for capabilities should be the last operation when performing
access control tests so that PF_SUPERPRIV is set only when it was required
for success (implying that the capability was needed for the operation).
Reported-by: Solar Designer <solar@openwall.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Serge Hallyn <serge@hallyn.com>
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
kmod <= v19 was broken -- it could return 0 to modprobe calls,
incorrectly assuming that a kernel module was built-in, whereas in
reality the module was just forming in the kernel. The reason for this
is an incorrect userspace heuristics. A userspace kmod fix is available
for it [0], however should userspace break again we could go on with
an failed get_fs_type() which is hard to debug as the request_module()
is detected as returning 0. The first suspect would be that there is
something worth with the kernel's module loader and obviously in this
case that is not the issue.
Since these issues are painful to debug complain when we know userspace
has outright lied to us.
[0] http://git.kernel.org/cgit/utils/kernel/kmod/kmod.git/commit/libkmod/libkmod-module.c?id=fd44a98ae2eb5eb32161088954ab21e58e19dfc4
Suggested-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jessica Yu <jeyu@redhat.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Instead of messing with the address limit to use vfs_read/vfs_writev.
Note that this requires that exported file implement ->read_iter and
->write_iter. All currently exportable file systems do this.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
De-dupliate some code and allow for passing the flags argument to
vfs_iter_write. Additionally it now properly updates timestamps.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
De-dupliate some code and allow for passing the flags argument to
vfs_iter_read. Additional it properly updates atime now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The checks for the permissions and can read / write flags are common
for the callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
opencode it in both callers to simplify the call stack a bit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
opencode it in both callers to simplify the call stack a bit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull block fixes from Jens Axboe:
"Two fixes that should go into this release.
One is an nvme regression fix from Keith, fixing a missing queue
freeze if the controller is being reset. This causes the reset to
hang.
The other is a fix for a leak of the bio protection info, if smaller
sized O_DIRECT is used. This fix should be more involved as we have
other problematic paths in the kernel, but given as this isn't a
regression in this series, we'll tackle those for 4.13"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: provide bio_uninit() free freeing integrity/task associations
nvme/pci: Fix stuck nvme reset
Commit 4751832da9 ("btrfs: fiemap: Cache and merge fiemap extent before
submit it to user") introduced a warning to catch unemitted cached
fiemap extent.
However such warning doesn't take the following case into consideration:
0 4K 8K
|<---- fiemap range --->|
|<----------- On-disk extent ------------------>|
In this case, the whole 0~8K is cached, and since it's larger than
fiemap range, it break the fiemap extent emit loop.
This leaves the fiemap extent cached but not emitted, and caught by the
final fiemap extent sanity check, causing kernel warning.
This patch removes the kernel warning and renames the sanity check to
emit_last_fiemap_cache() since it's possible and valid to have cached
fiemap extent.
Reported-by: David Sterba <dsterba@suse.cz>
Reported-by: Adam Borowski <kilobyte@angband.pl>
Fixes: 4751832da9 ("btrfs: fiemap: Cache and merge fiemap extent ...")
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When new directory 'DIR1' is created in a directory 'DIR0' with SGID bit
set, DIR1 is expected to have SGID bit set (and owning group equal to
the owning group of 'DIR0'). However when 'DIR0' also has some default
ACLs that 'DIR1' inherits, setting these ACLs will result in SGID bit on
'DIR1' to get cleared if user is not member of the owning group.
Fix the problem by moving posix_acl_update_mode() out of
__btrfs_set_acl() into btrfs_set_acl(). That way the function will not be
called when inheriting ACLs which is what we want as it prevents SGID
bit clearing and the mode has been properly set by posix_acl_create()
anyway.
Fixes: 073931017b
CC: stable@vger.kernel.org
CC: linux-btrfs@vger.kernel.org
CC: David Sterba <dsterba@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: David Sterba <dsterba@suse.com>
Dave Jones hit a WARN_ON(nr < 0) in btrfs_wait_ordered_roots() with
v4.12-rc6. This was because commit 70e7af244 made it possible for
calc_reclaim_items_nr() to return a negative number. It's not really a
bug in that commit, it just didn't go far enough down the stack to find
all the possible 64->32 bit overflows.
This switches calc_reclaim_items_nr() to return a u64 and changes everyone
that uses the results of that math to u64 as well.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Fixes: 70e7af2 ("Btrfs: fix delalloc accounting leak caused by u32 overflow")
Signed-off-by: Chris Mason <clm@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The commit "btrfs: scrub: inline helper scrub_setup_wr_ctx" inlined a
helper but wrongly sets up the target device. Incidentally there's a
local variable with the same name as a parameter in the previous
function, so this got caught during runtime as crash in test btrfs/027.
Reported-by: Chris Mason <clm@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[BUG]
For the following case, btrfs can underflow qgroup reserved space
at an error path:
(Page size 4K, function name without "btrfs_" prefix)
Task A | Task B
----------------------------------------------------------------------
Buffered_write [0, 2K) |
|- check_data_free_space() |
| |- qgroup_reserve_data() |
| Range aligned to page |
| range [0, 4K) <<< |
| 4K bytes reserved <<< |
|- copy pages to page cache |
| Buffered_write [2K, 4K)
| |- check_data_free_space()
| | |- qgroup_reserved_data()
| | Range alinged to page
| | range [0, 4K)
| | Already reserved by A <<<
| | 0 bytes reserved <<<
| |- delalloc_reserve_metadata()
| | And it *FAILED* (Maybe EQUOTA)
| |- free_reserved_data_space()
|- qgroup_free_data()
Range aligned to page range
[0, 4K)
Freeing 4K
(Special thanks to Chandan for the detailed report and analyse)
[CAUSE]
Above Task B is freeing reserved data range [0, 4K) which is actually
reserved by Task A.
And at writeback time, page dirty by Task A will go through writeback
routine, which will free 4K reserved data space at file extent insert
time, causing the qgroup underflow.
[FIX]
For btrfs_qgroup_free_data(), add @reserved parameter to only free
data ranges reserved by previous btrfs_qgroup_reserve_data().
So in above case, Task B will try to free 0 byte, so no underflow.
Reported-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Reviewed-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Tested-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Introduce a new parameter, struct extent_changeset for
btrfs_qgroup_reserved_data() and its callers.
Such extent_changeset was used in btrfs_qgroup_reserve_data() to record
which range it reserved in current reserve, so it can free it in error
paths.
The reason we need to export it to callers is, at buffered write error
path, without knowing what exactly which range we reserved in current
allocation, we can free space which is not reserved by us.
This will lead to qgroup reserved space underflow.
Reviewed-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[BUG]
Under the following case, we can underflow qgroup reserved space.
Task A | Task B
---------------------------------------------------------------
Quota disabled |
Buffered write |
|- btrfs_check_data_free_space() |
| *NO* qgroup space is reserved |
| since quota is *DISABLED* |
|- All pages are copied to page |
cache |
| Enable quota
| Quota scan finished
|
| Sync_fs
| |- run_delalloc_range
| |- Write pages
| |- btrfs_finish_ordered_io
| |- insert_reserved_file_extent
| |- btrfs_qgroup_release_data()
| Since no qgroup space is
reserved in Task A, we
underflow qgroup reserved
space
This can be detected by fstest btrfs/104.
[CAUSE]
In insert_reserved_file_extent() we tell qgroup to release the @ram_bytes
size of qgroup reserved_space in all cases.
And btrfs_qgroup_release_data() will check if quotas are enabled.
However in the above case, the buffered write happens before quota is
enabled, so we don't have the reserved space for that range.
[FIX]
In insert_reserved_file_extent(), we tell qgroup to release the acctual
byte number it released.
In the above case, since we don't have the reserved space, we tell
qgroups to release 0 byte, so the problem can be fixed.
And thanks to the @reserved parameter introduced by the qgroup rework,
and previous patch to return released bytes, the fix can be as small as
10 lines.
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
[ changelog updates ]
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_qgroup_release/free_data() only returns 0 or a negative error
number (ENOMEM is the only possible error).
This is normally good enough, but sometimes we need the exact byte
count it freed/released.
Change it to return actually released/freed bytenr number instead of 0
for success.
And slightly modify related extent_changeset structure, since in btrfs
one no-hole data extent won't be larger than 128M, so "unsigned int"
is large enough for the use case.
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Quite a lot of qgroup corruption happens due to wrong time of calling
btrfs_qgroup_prepare_account_extents().
Since the safest time is to call it just before
btrfs_qgroup_account_extents(), there is no need to separate these 2
functions.
Merging them will make code cleaner and less bug prone.
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
[ changelog and comment adjustments ]
Signed-off-by: David Sterba <dsterba@suse.com>
Modify btrfs_qgroup_account_extent() to exit quicker for non-fs extents.
The quick exit condition is:
1) The extent belongs to a non-fs tree
Only fs-tree extents can affect qgroup numbers and is the only case
where extent can be shared between different trees.
Although strictly speaking extent in data-reloc or tree-reloc tree
can be shared, data/tree-reloc root won't appear in the result of
btrfs_find_all_roots(), so we can ignore such case.
So we can check the first root in old_roots/new_roots ulist.
- if we find the 1st root is a not a fs/subvol root, then we can skip
the extent
- if we find the 1st root is a fs/subvol root, then we must continue
calculation
OR
2) both 'nr_old_roots' and 'nr_new_roots' are 0
This means either such extent got allocated then freed in current
transaction or it's a new reloc tree extent, whose nr_new_roots is 0.
Either way it won't affect qgroup accounting and can be skipped
safely.
Such quick exit can make trace output more quite and less confusing:
(example with fs uuid and time stamp removed)
Before:
------
add_delayed_tree_ref: bytenr=29556736 num_bytes=16384 action=ADD_DELAYED_REF parent=0(-) ref_root=2(EXTENT_TREE) level=0 type=TREE_BLOCK_REF seq=0
btrfs_qgroup_account_extent: bytenr=29556736 num_bytes=16384 nr_old_roots=0 nr_new_roots=1
------
Extent tree block will trigger btrfs_qgroup_account_extent() trace point
while no qgroup number is changed, as extent tree won't affect qgroup
accounting.
After:
------
add_delayed_tree_ref: bytenr=29556736 num_bytes=16384 action=ADD_DELAYED_REF parent=0(-) ref_root=2(EXTENT_TREE) level=0 type=TREE_BLOCK_REF seq=0
------
Now such unrelated extent won't trigger btrfs_qgroup_account_extent()
trace point, making the trace less noisy.
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
[ changelog and comment adjustments ]
Signed-off-by: David Sterba <dsterba@suse.com>
The total_bytes_pinned counter is completely broken when accounting
delayed refs:
- If two drops for the same extent are merged, we will decrement
total_bytes_pinned twice but only increment it once.
- If an add is merged into a drop or vice versa, we will decrement the
total_bytes_pinned counter but never increment it.
- If multiple references to an extent are dropped, we will account it
multiple times, potentially vastly over-estimating the number of bytes
that will be freed by a commit and doing unnecessary work when we're
close to ENOSPC.
The last issue is relatively minor, but the first two make the
total_bytes_pinned counter leak or underflow very often. These
accounting issues were introduced in b150a4f10d ("Btrfs: use a percpu
to keep track of possibly pinned bytes"), but they were papered over by
zeroing out the counter on every commit until d288db5dc0 ("Btrfs: fix
race of using total_bytes_pinned").
We need to make sure that an extent is accounted as pinned exactly once
if and only if we will drop references to it when when the transaction
is committed. Ideally we would only add to total_bytes_pinned when the
*last* reference is dropped, but this information isn't readily
available for data extents. Again, this over-estimation can lead to
extra commits when we're close to ENOSPC, but it's not as bad as before.
The fix implemented here is to increment total_bytes_pinned when the
total refmod count for an extent goes negative and decrement it if the
refmod count goes back to non-negative or after we've run all of the
delayed refs for that extent.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We need this to decide when to account pinned bytes.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Currently, we only increment total_bytes_pinned in
btrfs_free_tree_block() when dropping the last reference on the block.
However, when the delayed ref is run later, we will decrement
total_bytes_pinned regardless of whether it was the last reference or
not. This causes the counter to underflow when the reference we dropped
was not the last reference. Fix it by incrementing the counter
unconditionally, which is what btrfs_free_extent() does. This makes
total_bytes_pinned an overestimate when references to shared extents are
dropped, but in the worst case this will just make us try to commit the
transaction to try to free up space and find we didn't free enough.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The extents marked in pin_down_extent() will be unpinned later in
unpin_extent_range(), which decrements total_bytes_pinned.
pin_down_extent() must increment the counter to avoid underflowing it.
Also adjust btrfs_free_tree_block() to avoid accounting for the same
extent twice.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The value of flags is one of DATA/METADATA/SYSTEM, they must exist at
when add_pinned_bytes is called.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ added changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
There are a few places where we pass in a negative num_bytes, so make it
signed for clarity. Also move it up in the file since later patches will
need it there.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The XATTR_ITEM is a type of a directory item so we use the common
validator helper. Unlike other dir items, it can have data. The way the
name len validation is currently implemented does not reflect that. We'd
have to adjust by the data_len when comparing the read and item limits.
However, this will not work for multi-item xattr dir items.
Example from tree dump of generic/337:
item 7 key (257 XATTR_ITEM 751495445) itemoff 15667 itemsize 147
location key (0 UNKNOWN.0 0) type XATTR
transid 8 data_len 3 name_len 11
name: user.foobar
data 123
location key (0 UNKNOWN.0 0) type XATTR
transid 8 data_len 6 name_len 13
name: user.WvG1c1Td
data qwerty
location key (0 UNKNOWN.0 0) type XATTR
transid 8 data_len 5 name_len 19
name: user.J3__T_Km3dVsW_
data hello
At the point of btrfs_is_name_len_valid call we don't have access to the
data_len value of the 2nd and 3rd sub-item. So simple btrfs_dir_data_len(leaf,
di) would always return 3, although we'd need to get 6 and 5 respectively to
get the claculations right. (read_end + name_len + data_len vs item_end)
We'd have to also pass data_len externally, which is not point of the
name validation. The last check is supposed to test if there's at least
one dir item space after the one we're processing. I don't think this is
particularly useful, validation of the next item would catch that too.
So the check is removed and we don't weaken the validation. Now tests
btrfs/048, btrfs/053, generic/273 and generic/337 pass.
Signed-off-by: David Sterba <dsterba@suse.com>
Wen reports significant memory leaks with DIF and O_DIRECT:
"With nvme devive + T10 enabled, On a system it has 256GB and started
logging /proc/meminfo & /proc/slabinfo for every minute and in an hour
it increased by 15968128 kB or ~15+GB.. Approximately 256 MB / minute
leaking.
/proc/meminfo | grep SUnreclaim...
SUnreclaim: 6752128 kB
SUnreclaim: 6874880 kB
SUnreclaim: 7238080 kB
....
SUnreclaim: 22307264 kB
SUnreclaim: 22485888 kB
SUnreclaim: 22720256 kB
When testcases with T10 enabled call into __blkdev_direct_IO_simple,
code doesn't free memory allocated by bio_integrity_alloc. The patch
fixes the issue. HTX has been run with +60 hours without failure."
Since __blkdev_direct_IO_simple() allocates the bio on the stack, it
doesn't go through the regular bio free. This means that any ancillary
data allocated with the bio through the stack is not freed. Hence, we
can leak the integrity data associated with the bio, if the device is
using DIF/DIX.
Fix this by providing a bio_uninit() and export it, so that we can use
it to free this data. Note that this is a minimal fix for this issue.
Any current user of bio's that are allocated outside of
bio_alloc_bioset() suffers from this issue, most notably some drivers.
We will fix those in a more comprehensive patch for 4.13. This also
means that the commit marked as being fixed by this isn't the real
culprit, it's just the most obvious one out there.
Fixes: 542ff7bf18 ("block: new direct I/O implementation")
Reported-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Bugfixes include:
- Stable fix for exclusive create if the server supports the umask attribute
- Trunking detection should handle ERESTARTSYS/EINTR
- Stable fix for a race in the LAYOUTGET function
- Stable fix to revert "nfs_rename() handle -ERESTARTSYS dentry left behind"
- nfs4_callback_free_slot() cannot call nfs4_slot_tbl_drain_complete()
-----BEGIN PGP SIGNATURE-----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=w19C
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.12-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Bugfixes include:
- stable fix for exclusive create if the server supports the umask
attribute
- trunking detection should handle ERESTARTSYS/EINTR
- stable fix for a race in the LAYOUTGET function
- stable fix to revert "nfs_rename() handle -ERESTARTSYS dentry left
behind"
- nfs4_callback_free_slot() cannot call nfs4_slot_tbl_drain_complete()"
* tag 'nfs-for-4.12-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4.1: nfs4_callback_free_slot() cannot call nfs4_slot_tbl_drain_complete()
Revert "NFS: nfs_rename() handle -ERESTARTSYS dentry left behind"
NFSv4.1: Fix a race in nfs4_proc_layoutget
NFS: Trunking detection should handle ERESTARTSYS/EINTR
NFSv4.2: Don't send mode again in post-EXCLUSIVE4_1 SETATTR with umask
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZPdbLAAoJEHm+PkMAQRiGx4wH/1nCjfnl6fE8oJ24/1gEAOUh
biFdqJkYZmlLYHVtYfLm4Ueg4adJdg0wx6qM/4RaAzmQVvLfDV34bc1qBf1+P95G
kVF+osWyXrZo5cTwkwapHW/KNu4VJwAx2D1wrlxKDVG5AOrULH1pYOYGOpApEkZU
4N+q5+M0ce0GJpqtUZX+UnI33ygjdDbBxXoFKsr24B7eA0ouGbAJ7dC88WcaETL+
2/7tT01SvDMo0jBSV0WIqlgXwZ5gp3yPGnklC3F4159Yze6VFrzHMKS/UpPF8o8E
W9EbuzwxsKyXUifX2GY348L1f+47glen/1sedbuKnFhP6E9aqUQQJXvEO7ueQl4=
=m2Gx
-----END PGP SIGNATURE-----
Merge tag 'v4.12-rc5' into nfsd tree
Update to get f0c3192cee "virtio_net: lower limit on buffer size".
That bug was interfering with my nfsd testing.
Some architectures (at least PPC) doesn't like get/put_user with
64-bit types on a 32-bit system. Use the variably sized copy
to/from user variants instead.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: c75b1d9421 ("fs: add fcntl() interface for setting/getting write life time hints")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When copying up a file that has multiple hard links we need to break any
association with the origin file. This makes copy-up be essentially an
atomic replace.
The new file has nothing to do with the old one (except having the same
data and metadata initially), so don't set the overlay.origin attribute.
We can relax this in the future when we are able to index upper object by
origin.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 3a1e819b4e ("ovl: store file handle of lower inode on copy up")
Nothing prevents mischief on upper layer while we are busy copying up the
data.
Move the lookup right before the looked up dentry is actually used.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 01ad3eb8a0 ("ovl: concurrent copy up of regular files")
Cc: <stable@vger.kernel.org> # v4.11
The current code works only for the case where we have exactly one slot,
which is no longer true.
nfs4_free_slot() will automatically declare the callback channel to be
drained when all slots have been returned.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
This reverts commit 920b4530fb which could
call d_move() without holding the directory's i_mutex, and reverts commit
d4ea7e3c5c "NFS: Fix old dentry rehash after
move", which was a follow-up fix.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Fixes: 920b4530fb ("NFS: nfs_rename() handle -ERESTARTSYS dentry left behind")
Cc: stable@vger.kernel.org # v4.10+
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
If the task calling layoutget is signalled, then it is possible for the
calls to nfs4_sequence_free_slot() and nfs4_layoutget_prepare() to race,
in which case we leak a slot.
The fix is to move the call to nfs4_sequence_free_slot() into the
nfs4_layoutget_release() so that it gets called at task teardown time.
Fixes: 2e80dbe7ac ("NFSv4.1: Close callback races for OPEN, LAYOUTGET...")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Add a new dqget flag that grabs the dquot without taking the ilock.
This will be used by the scrubber (which will have already grabbed
the ilock) to perform basic sanity checking of the quota data.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
When new directory 'DIR1' is created in a directory 'DIR0' with SGID bit
set, DIR1 is expected to have SGID bit set (and owning group equal to
the owning group of 'DIR0'). However when 'DIR0' also has some default
ACLs that 'DIR1' inherits, setting these ACLs will result in SGID bit on
'DIR1' to get cleared if user is not member of the owning group.
Fix the problem by calling __xfs_set_acl() instead of xfs_set_acl() when
setting up inode in xfs_generic_create(). That prevents SGID bit
clearing and mode is properly set by posix_acl_create() anyway. We also
reorder arguments of __xfs_set_acl() to match the ordering of
xfs_set_acl() to make things consistent.
Fixes: 073931017b
CC: stable@vger.kernel.org
CC: Darrick J. Wong <darrick.wong@oracle.com>
CC: linux-xfs@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
XFS runs an eofblocks reclaim scan before returning an ENOSPC error to
userspace for buffered writes. This facilitates aggressive speculative
preallocation without causing user visible side effects such as
premature ENOSPC.
Run a cowblocks scan in the same situation to reclaim lingering COW fork
preallocation throughout the filesystem.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Now that error injection tags support dynamic frequency adjustment,
replace the debug mode sysfs knob that controls log record CRC error
injection with an error injection tag.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
We now have enhanced error injection that can control the frequency
with which errors happen, so convert drop_writes to use this.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Since we moved the injected error frequency controls to the mountpoint,
we can get rid of the last argument to XFS_TEST_ERROR.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Creates a /sys/fs/xfs/$dev/errortag/ directory to control the errortag
values directly. This enables us to control the randomness values,
rather than having to accept the defaults.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Remove the xfs_etest structure in favor of a per-mountpoint structure.
This will give us the flexibility to set as many error injection points
as we want, and later enable us to set up sysfs knobs to set the trigger
frequency as we wish. This comes at a cost of higher memory use, but
unti we hit 1024 injection points (we're at 29) or a lot of mounts this
shouldn't be a huge issue.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Use memdup_user() helper instead of open-coding to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Now that all callers of the pmem api have been converted to dax helpers that
call back to the pmem driver, we can remove include/linux/pmem.h and
asm/pmem.h.
Cc: <x86@kernel.org>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Oliver O'Halloran <oohall@gmail.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Chris Mason <clm@fb.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Define a set of write life time hints:
RWH_WRITE_LIFE_NOT_SET No hint information set
RWH_WRITE_LIFE_NONE No hints about write life time
RWH_WRITE_LIFE_SHORT Data written has a short life time
RWH_WRITE_LIFE_MEDIUM Data written has a medium life time
RWH_WRITE_LIFE_LONG Data written has a long life time
RWH_WRITE_LIFE_EXTREME Data written has an extremely long life time
The intent is for these values to be relative to each other, no
absolute meaning should be attached to these flag names.
Add an fcntl interface for querying these flags, and also for
setting them as well:
F_GET_RW_HINT Returns the read/write hint set on the
underlying inode.
F_SET_RW_HINT Set one of the above write hints on the
underlying inode.
F_GET_FILE_RW_HINT Returns the read/write hint set on the
file descriptor.
F_SET_FILE_RW_HINT Set one of the above write hints on the
file descriptor.
The user passes in a 64-bit pointer to get/set these values, and
the interface returns 0/-1 on success/error.
Sample program testing/implementing basic setting/getting of write
hints is below.
Add support for storing the write life time hint in the inode flags
and in struct file as well, and pass them to the kiocb flags. If
both a file and its corresponding inode has a write hint, then we
use the one in the file, if available. The file hint can be used
for sync/direct IO, for buffered writeback only the inode hint
is available.
This is in preparation for utilizing these hints in the block layer,
to guide on-media data placement.
/*
* writehint.c: get or set an inode write hint
*/
#include <stdio.h>
#include <fcntl.h>
#include <stdlib.h>
#include <unistd.h>
#include <stdbool.h>
#include <inttypes.h>
#ifndef F_GET_RW_HINT
#define F_LINUX_SPECIFIC_BASE 1024
#define F_GET_RW_HINT (F_LINUX_SPECIFIC_BASE + 11)
#define F_SET_RW_HINT (F_LINUX_SPECIFIC_BASE + 12)
#endif
static char *str[] = { "RWF_WRITE_LIFE_NOT_SET", "RWH_WRITE_LIFE_NONE",
"RWH_WRITE_LIFE_SHORT", "RWH_WRITE_LIFE_MEDIUM",
"RWH_WRITE_LIFE_LONG", "RWH_WRITE_LIFE_EXTREME" };
int main(int argc, char *argv[])
{
uint64_t hint;
int fd, ret;
if (argc < 2) {
fprintf(stderr, "%s: file <hint>\n", argv[0]);
return 1;
}
fd = open(argv[1], O_RDONLY);
if (fd < 0) {
perror("open");
return 2;
}
if (argc > 2) {
hint = atoi(argv[2]);
ret = fcntl(fd, F_SET_RW_HINT, &hint);
if (ret < 0) {
perror("fcntl: F_SET_RW_HINT");
return 4;
}
}
ret = fcntl(fd, F_GET_RW_HINT, &hint);
if (ret < 0) {
perror("fcntl: F_GET_RW_HINT");
return 3;
}
printf("%s: hint %s\n", argv[1], str[hint]);
close(fd);
return 0;
}
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
... and lose HAVE_ARCH_...; if copy_{to,from}_user() on an
architecture sucks badly enough to make it a problem, we have
a worse problem.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Log recovery allocates in-core transaction and member item data
structures on-demand as it processes the on-disk log. Transactions
are allocated on first encounter on-disk and stored in a hash table
structure where they are easily accessible for subsequent lookups.
Transaction items are also allocated on demand and are attached to
the associated transactions.
When a commit record is encountered in the log, the transaction is
committed to the fs and the in-core structures are freed. If a
filesystem crashes or shuts down before all in-core log buffers are
flushed to the log, however, not all transactions may have commit
records in the log. As expected, the modifications in such an
incomplete transaction are not replayed to the fs. The in-core data
structures for the partial transaction are never freed, however,
resulting in a memory leak.
Update xlog_do_recovery_pass() to first correctly initialize the
hash table array so empty lists can be distinguished from populated
lists on function exit. Update xlog_recover_free_trans() to always
remove the transaction from the list prior to freeing the associated
memory. Finally, walk the hash table of transaction lists as the
last step before it goes out of scope and free any transactions that
may remain on the lists. This prevents a memory leak of partial
transactions in the log.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
This makes it consistent with ->is_encrypted(), ->empty_dir(), and
fscrypt_dummy_context_enabled().
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
fscrypt provides facilities to use different encryption algorithms which
are selectable by userspace when setting the encryption policy. Currently,
only AES-256-XTS for file contents and AES-256-CBC-CTS for file names are
implemented. This is a clear case of kernel offers the mechanism and
userspace selects a policy. Similar to what dm-crypt and ecryptfs have.
This patch adds support for using AES-128-CBC for file contents and
AES-128-CBC-CTS for file name encryption. To mitigate watermarking
attacks, IVs are generated using the ESSIV algorithm. While AES-CBC is
actually slightly less secure than AES-XTS from a security point of view,
there is more widespread hardware support. Using AES-CBC gives us the
acceptable performance while still providing a moderate level of security
for persistent storage.
Especially low-powered embedded devices with crypto accelerators such as
CAAM or CESA often only support AES-CBC. Since using AES-CBC over AES-XTS
is basically thought of a last resort, we use AES-128-CBC over AES-256-CBC
since it has less encryption rounds and yields noticeable better
performance starting from a file size of just a few kB.
Signed-off-by: Daniel Walter <dwalter@sigma-star.at>
[david@sigma-star.at: addressed review comments]
Signed-off-by: David Gstir <david@sigma-star.at>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
fscrypt_free_filename() only needs to do a kfree() of crypto_buf.name,
which works well as an inline function. We can skip setting the various
pointers to NULL, since no user cares about it (the name is always freed
just before it goes out of scope).
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: David Gstir <david@sigma-star.at>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Currently, filesystems allow truncate(2) on an encrypted file without
the encryption key. However, it's impossible to correctly handle the
case where the size being truncated to is not a multiple of the
filesystem block size, because that would require decrypting the final
block, zeroing the part beyond i_size, then encrypting the block.
As other modifications to encrypted file contents are prohibited without
the key, just prohibit truncate(2) as well, making it fail with ENOKEY.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Since only an open file can be mmap'ed, and we only allow open()ing an
encrypted file when its key is available, there is no need to check for
the key again before permitting each mmap().
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Merge misc fixes from Andrew Morton:
"8 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
fs/exec.c: account for argv/envp pointers
ocfs2: fix deadlock caused by recursive locking in xattr
slub: make sysfs file removal asynchronous
lib/cmdline.c: fix get_options() overflow while parsing ranges
fs/dax.c: fix inefficiency in dax_writeback_mapping_range()
autofs: sanity check status reported with AUTOFS_DEV_IOCTL_FAIL
mm/vmalloc.c: huge-vmap: fail gracefully on unexpected huge vmap mappings
mm, thp: remove cond_resched from __collapse_huge_page_copy
When limiting the argv/envp strings during exec to 1/4 of the stack limit,
the storage of the pointers to the strings was not included. This means
that an exec with huge numbers of tiny strings could eat 1/4 of the stack
limit in strings and then additional space would be later used by the
pointers to the strings.
For example, on 32-bit with a 8MB stack rlimit, an exec with 1677721
single-byte strings would consume less than 2MB of stack, the max (8MB /
4) amount allowed, but the pointers to the strings would consume the
remaining additional stack space (1677721 * 4 == 6710884).
The result (1677721 + 6710884 == 8388605) would exhaust stack space
entirely. Controlling this stack exhaustion could result in
pathological behavior in setuid binaries (CVE-2017-1000365).
[akpm@linux-foundation.org: additional commenting from Kees]
Fixes: b6a2fea393 ("mm: variable length argument support")
Link: http://lkml.kernel.org/r/20170622001720.GA32173@beast
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Qualys Security Advisory <qsa@qualys.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Another deadlock path caused by recursive locking is reported. This
kind of issue was introduced since commit 743b5f1434 ("ocfs2: take
inode lock in ocfs2_iop_set/get_acl()"). Two deadlock paths have been
fixed by commit b891fa5024 ("ocfs2: fix deadlock issue when taking
inode lock at vfs entry points"). Yes, we intend to fix this kind of
case in incremental way, because it's hard to find out all possible
paths at once.
This one can be reproduced like this. On node1, cp a large file from
home directory to ocfs2 mountpoint. While on node2, run
setfacl/getfacl. Both nodes will hang up there. The backtraces:
On node1:
__ocfs2_cluster_lock.isra.39+0x357/0x740 [ocfs2]
ocfs2_inode_lock_full_nested+0x17d/0x840 [ocfs2]
ocfs2_write_begin+0x43/0x1a0 [ocfs2]
generic_perform_write+0xa9/0x180
__generic_file_write_iter+0x1aa/0x1d0
ocfs2_file_write_iter+0x4f4/0xb40 [ocfs2]
__vfs_write+0xc3/0x130
vfs_write+0xb1/0x1a0
SyS_write+0x46/0xa0
On node2:
__ocfs2_cluster_lock.isra.39+0x357/0x740 [ocfs2]
ocfs2_inode_lock_full_nested+0x17d/0x840 [ocfs2]
ocfs2_xattr_set+0x12e/0xe80 [ocfs2]
ocfs2_set_acl+0x22d/0x260 [ocfs2]
ocfs2_iop_set_acl+0x65/0xb0 [ocfs2]
set_posix_acl+0x75/0xb0
posix_acl_xattr_set+0x49/0xa0
__vfs_setxattr+0x69/0x80
__vfs_setxattr_noperm+0x72/0x1a0
vfs_setxattr+0xa7/0xb0
setxattr+0x12d/0x190
path_setxattr+0x9f/0xb0
SyS_setxattr+0x14/0x20
Fix this one by using ocfs2_inode_{lock|unlock}_tracker, which is
exported by commit 439a36b8ef ("ocfs2/dlmglue: prepare tracking logic
to avoid recursive cluster lock").
Link: http://lkml.kernel.org/r/20170622014746.5815-1-zren@suse.com
Fixes: 743b5f1434 ("ocfs2: take inode lock in ocfs2_iop_set/get_acl()")
Signed-off-by: Eric Ren <zren@suse.com>
Reported-by: Thomas Voegtle <tv@lio96.de>
Tested-by: Thomas Voegtle <tv@lio96.de>
Reviewed-by: Joseph Qi <jiangqi903@gmail.com>
Cc: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dax_writeback_mapping_range() fails to update iteration index when
searching radix tree for entries needing cache flushing. Thus each
pagevec worth of entries is searched starting from the start which is
inefficient and prone to livelocks. Update index properly.
Link: http://lkml.kernel.org/r/20170619124531.21491-1-jack@suse.cz
Fixes: 9973c98ecf ("dax: add support for fsync/sync")
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a positive status is passed with the AUTOFS_DEV_IOCTL_FAIL ioctl,
autofs4_d_automount() will return
ERR_PTR(status)
with that status to follow_automount(), which will then dereference an
invalid pointer.
So treat a positive status the same as zero, and map to ENOENT.
See comment in systemd src/core/automount.c::automount_send_ready().
Link: http://lkml.kernel.org/r/871sqwczx5.fsf@notabene.neil.brown.name
Signed-off-by: NeilBrown <neilb@suse.com>
Cc: Ian Kent <raven@themaw.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- don't allow swapon on files on the realtime device, because the swap
code will swap pages out to blocks on the data device, thereby
corrupting the filesystem
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qkCp
-----END PGP SIGNATURE-----
Merge tag 'xfs-4.12-fixes-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"I have one more bugfix for you for 4.12-rc7 to fix a disk corruption
problem:
- don't allow swapon on files on the realtime device, because the
swap code will swap pages out to blocks on the data device, thereby
corrupting the filesystem"
* tag 'xfs-4.12-fixes-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: don't allow bmap on rt files
The main loop in __discard_prealloc is protected by the reiserfs write lock
which is dropped across schedules like the BKL it replaced. The problem is
that it checks the value, calls a routine that schedules, and then adjusts
the state. As a result, two threads that are calling
reiserfs_prealloc_discard at the same time can race when one calls
reiserfs_free_prealloc_block, the lock is dropped, and the other calls
reiserfs_free_prealloc_block with the same block number. In the right
circumstances, it can cause the prealloc count to go negative.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Most extended attributes will fit in a single block. More importantly,
we drop the reference to the inode while holding the transaction open
so the preallocated blocks aren't released. As a result, the inode
may be evicted before it's removed from the transaction's prealloc list
which can cause memory corruption.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
kstrtoull returns 0 on success, however, in reserved_clusters_store we
will return -EINVAL if kstrtoull returns 0, it makes us fail to update
reserved_clusters value through sysfs.
Fixes: 76d33bca55
Cc: stable@vger.kernel.org # 4.4
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
For 1k-block filesystems, the filesystem starts at block 1, not block 0.
This fact is recorded in s_first_data_block, so use that to bump up the
start_fsb before we start querying the filesystem for its space map.
Without this, ext4/026 fails on 1k block ext4 because various functions
(notably ext4_get_group_no_and_offset) don't know what to do with an
fsblock that is "before" the start of the filesystem and return garbage
results (blockgroup 2^32-1, etc.) that confuse fsmap.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Previously a bad directory block with a bad checksum is skipped; we
should be returning EFSBADCRC (aka EBADMSG).
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Previously, a read error would be ignored and we would eventually return
NULL from ext4_find_entry, which signals "no such file or directory". We
should be returning EIO.
Signed-off-by: Khazhismel Kumykov <khazhy@google.com>
Currently it's possible to encrypt all files and directories on an ext4
filesystem by deleting everything, including lost+found, then setting an
encryption policy on the root directory. However, this is incompatible
with e2fsck because e2fsck expects to find, create, and/or write to
lost+found and does not have access to any encryption keys. Especially
problematic is that if e2fsck can't find lost+found, it will create it
without regard for whether the root directory is encrypted. This is
wrong for obvious reasons, and it causes a later run of e2fsck to
consider the lost+found directory entry to be corrupted.
Encrypting the root directory may also be of limited use because it is
the "all-or-nothing" use case, for which dm-crypt can be used instead.
(By design, encryption policies are inherited and cannot be overridden;
so the root directory having an encryption policy implies that all files
and directories on the filesystem have that same encryption policy.)
In any case, encrypting the root directory is broken currently and must
not be allowed; so start returning an error if userspace requests it.
For now only do this in ext4, because f2fs and ubifs do not appear to
have the lost+found requirement. We could move it into
fscrypt_ioctl_set_policy() later if desired, though.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Now, when we mount ext4 filesystem with '-o discard' option, we have to
issue all the discard commands for the blocks to be deallocated and
wait for the completion of the commands on the commit complete phase.
Because this procedure might involve a lot of sequential combinations of
issuing discard commands and waiting for that, the delay of this
procedure might be too much long, even to 17.0s in our test,
and it results in long commit delay and fsync() performance degradation.
To reduce this kind of delay, instead of adding callback for each
extent and handling all of them in a sequential manner on commit phase,
we instead add a separate list of extents to free to the superblock and
then process this list at once after transaction commits so that
we can issue all the discard commands in a parallel manner like XFS
filesystem.
Finally, we could enhance the discard command handling performance.
The result was such that 17.0s delay of a single commit in the worst
case has been enhanced to 4.8s.
Signed-off-by: Daeho Jeong <daeho.jeong@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Tested-by: Hobin Woo <hobin.woo@samsung.com>
Tested-by: Kitae Lee <kitae87.lee@samsung.com>
Reviewed-by: Jan Kara <jack@suse.cz>
These days inode reclaim calls evict_inode() only when it has no pages
in the mapping. In that case it is not necessary to wait for transaction
commit in ext4_evict_inode() as there can be no pages waiting to be
committed. So avoid unnecessary transaction waiting in that case.
We still have to keep the check for the case where ext4_evict_inode()
gets called from other paths (e.g. umount) where inode still can have
some page cache pages.
Reported-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Pull cifs fixes from Steve French:
"Various small fixes for stable"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix some return values in case of error in 'crypt_message'
cifs: remove redundant return in cifs_creation_time_get
CIFS: Improve readdir verbosity
CIFS: check if pages is null rather than bv for a failed allocation
CIFS: Set ->should_dirty in cifs_user_readv()
The main purpose of mb cache is to achieve deduplication in
extended attributes. In use cases where opportunity for deduplication
is unlikely, it only adds overhead.
Add a mount option to explicitly turn off mb cache.
Suggested-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
To verify that a xattr entry is not pointing to the wrong xattr inode,
we currently check that the target inode has EXT4_EA_INODE_FL flag set and
also the entry size matches the target inode size.
For stronger validation, also incorporate crc32c hash of the value into
the e_hash field. This is done regardless of whether the entry lives in
the inode body or external attribute block.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
When an extended attribute block is modified, ext4_xattr_hash_entry()
recalculates e_hash for the entry that is pointed by s->here. This is
unnecessary if the modification is to remove an entry.
Currently, if the removed entry is the last one and there are other
entries remaining, hash calculation targets the just erased entry which
has been filled with zeroes and effectively does nothing. If the removed
entry is not the last one and there are more entries, this time it will
recalculate hash on the next entry which is totally unnecessary.
Fix these by moving the decision on when to recalculate hash to
ext4_xattr_set_entry().
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
New ea_inode feature allows putting large xattr values into external
inodes. struct ext4_xattr_entry and the attribute name however have to
remain in the inode extra space or external attribute block. Once that
space is exhausted, no further entries can be added. Some of that space
could also be used by values that fit in there at the time of addition.
So, a single xattr entry whose value barely fits in the external block
could prevent further entries being added.
To mitigate the problem, this patch introduces a notion of reserved
space in the external attribute block that cannot be used by value data.
This reserve is enforced when ea_inode feature is enabled. The amount
of reserve is arbitrarily chosen to be min(block_size/8, 1024). The
table below shows how much space is reserved for each block size and the
guaranteed mininum number of entries that can be placed in the external
attribute block.
block size reserved bytes entries (name length = 16)
1k 128 3
2k 256 7
4k 512 15
8k 1024 31
16k 1024 31
32k 1024 31
64k 1024 31
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Ext4 ea_inode feature allows storing xattr values in external inodes to
be able to store values that are bigger than a block in size. Ext4 also
has deduplication support for these type of inodes. With deduplication,
the actual storage waste is eliminated but the users of such inodes are
still charged full quota for the inodes as if there was no sharing
happening in the background.
This design requires ext4 to manually charge the users because the
inodes are shared.
An implication of this is that, if someone calls chown on a file that
has such references we need to transfer the quota for the file and xattr
inodes. Current dquot_transfer() function implicitly transfers one inode
charge. With ea_inode feature, we would like to transfer multiple inode
charges.
Add get_inode_usage callback which can interrogate the total number of
inodes that were charged for a given inode.
[ Applied fix from Colin King to make sure the 'ret' variable is
initialized on the successful return path. Detected by
CoverityScan, CID#1446616 ("Uninitialized scalar variable") --tytso]
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jan Kara <jack@suse.cz>
Ext4 now supports xattr values that are up to 64k in size (vfs limit).
Large xattr values are stored in external inodes each one holding a
single value. Once written the data blocks of these inodes are immutable.
The real world use cases are expected to have a lot of value duplication
such as inherited acls etc. To reduce data duplication on disk, this patch
implements a deduplicator that allows sharing of xattr inodes.
The deduplication is based on an in-memory hash lookup that is a best
effort sharing scheme. When a xattr inode is read from disk (i.e.
getxattr() call), its crc32c hash is added to a hash table. Before
creating a new xattr inode for a value being set, the hash table is
checked to see if an existing inode holds an identical value. If such an
inode is found, the ref count on that inode is incremented. On value
removal the ref count is decremented and if it reaches zero the inode is
deleted.
The quota charging for such inodes is manually managed. Every reference
holder is charged the full size as if there was no sharing happening.
This is consistent with how xattr blocks are also charged.
[ Fixed up journal credits calculation to handle inline data and the
rare case where an shared xattr block can get freed when two thread
race on breaking the xattr block sharing. --tytso ]
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
During inode deletion, the number of journal credits that will be
needed is hard to determine. For that reason we have journal
extend/restart calls in several places. Whenever a transaction is
restarted, filesystem must be in a consistent state because there is
no atomicity guarantee beyond a restart call.
Add ext4_xattr_ensure_credits() helper function which takes care of
journal extend/restart logic. It also handles getting jbd2 write
access and dirty metadata calls. This function is called at every
iteration of handling an ea_inode reference.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
IS_NOQUOTA() indicates whether quota is disabled for an inode. Ext4
also uses it to check whether an inode is for a quota file. The
distinction currently doesn't matter because quota is disabled only
for the quota files. When we start disabling quota for other inodes
in the future, we will want to make the distinction clear.
Replace IS_NOQUOTA() call with ext4_is_quota_file() at places where
we are checking for quota files.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
There will be a second mb_cache instance that tracks ea_inodes. Make
existing names more explicit so that it is clear that they refer to
xattr block cache.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Make names more generic so that mbcache usage is not limited to
block sharing. In a subsequent patch in the series
("ext4: xattr inode deduplication"), we start using the mbcache code
for sharing xattr inodes. With that patch, old mb_cache_entry.e_block
field could be holding either a block number or an inode number.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Since this is a xattr specific data structure it is cleaner to keep it in
xattr header file.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Tracking struct inode * rather than the inode number eliminates the
repeated ext4_xattr_inode_iget() call later. The second call cannot
fail in practice but still requires explanation when it wants to ignore
the return value. Avoid the trouble and make things simple.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
bmap returns a dumb LBA address but not the block device that goes with
that LBA. Swapfiles don't care about this and will blindly assume that
the data volume is the correct blockdev, which is totally bogus for
files on the rt subvolume. This results in the swap code doing IOs to
arbitrary locations on the data device(!) if the passed in mapping is a
realtime file, so just turn off bmap for rt files.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Both ext4_set_acl() and ext4_set_context() need to be made aware of
ea_inode feature when it comes to credits calculation.
Also add a sufficient credits check in ext4_xattr_set_handle() right
after xattr write lock is grabbed. Original credits calculation is done
outside the lock so there is a possiblity that the initially calculated
credits are not sufficient anymore.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
In a few places the function returns without trying to pass the actual
error code to the caller. Fix those.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
When value size is <= EXT4_XATTR_MIN_LARGE_EA_SIZE(), and it
doesn't fit in either inline or xattr block, a second try is made to
store it in an external inode while storing the entry itself in inline
area. There should also be an attempt to store the entry in xattr block.
This patch adds a retry loop to do that. It also makes the caller the
sole decider on whether to store a value in an external inode.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
When there is no space for a value in xattr block, it may be stored
in an xattr inode even if the value length is less than
EXT4_XATTR_MIN_LARGE_EA_SIZE(). So the current assumption in credits
calculation is wrong.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
When a xattr entry refers to an external inode, the value data is not
available in the inline area so we should not attempt to read it using
value offset.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
When moving xattr entries from inline area to a xattr block, entries
that refer to external xattr inodes need special handling because
value data is not available in the inline area but rather should be
read from its external inode.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
ext4_xattr_make_inode_space() is interested in calculating the inline
space used in an inode. When a xattr entry refers to an external inode
the value size indicates the external inode size, not the value size in
the inline area. Change the function to take this into account.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
ext4_xattr_value_same() is used as a quick optimization in case the new
xattr value is identical to the previous value. When xattr value is
stored in a xattr inode the check becomes expensive so it is better to
just assume that they are not equal.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Two places in code missed converting xattr inode number using
le32_to_cpu().
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The input and output values of *size parameter are equal on successful
return from ext4_xattr_inode_get(). On error return, the callers ignore
the output value so there is no need to update it.
Also check for NULL return from ext4_bread(). If the actual xattr inode
size happens to be smaller than the expected size, ext4_bread() may
return NULL which would indicate data corruption.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
In general, kernel functions indicate success/failure through their return
values. This function returns the status as an output parameter and reserves
the return value for the inode. Make it follow the general convention.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
EXT4_XATTR_MAX_LARGE_EA_SIZE definition in ext4 is currently unused.
Besides, vfs enforces its own 64k limit which makes the 1MB limit in
ext4 redundant. Remove it.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The ref count on ea_inode is incremented by
ext4_xattr_inode_orphan_add() which is supposed to be decremented by
ext4_xattr_inode_array_free(). The decrement is conditioned on whether
the ea_inode is currently on the orphan list. However, the orphan list
addition only happens when journaling is enabled. In non-journaled case,r
we fail to release the ref count causing an error message like below.
"VFS: Busy inodes after unmount of sdb. Self-destruct in 5 seconds.
Have a nice day..."
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
ea_inode contents are treated as metadata, that's why it is journaled
during initial writes. Failing to call revoke during freeing could cause
user data to be overwritten with original ea_inode contents during journal
replay.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Quota charging is based on the ownership of the inode. Currently, the
xattr inode owner is set to the caller which may be different from the
parent inode owner. This is inconsistent with how quota is charged for
xattr block and regular data block writes.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
We don't need acls on xattr inodes because they are not directly
accessible from user mode.
Besides lockdep complains about recursive locking of xattr_sem as seen
below.
=============================================
[ INFO: possible recursive locking detected ]
4.11.0-rc8+ #402 Not tainted
---------------------------------------------
python/1894 is trying to acquire lock:
(&ei->xattr_sem){++++..}, at: [<ffffffff804878a6>] ext4_xattr_get+0x66/0x270
but task is already holding lock:
(&ei->xattr_sem){++++..}, at: [<ffffffff80489500>] ext4_xattr_set_handle+0xa0/0x5d0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&ei->xattr_sem);
lock(&ei->xattr_sem);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by python/1894:
#0: (sb_writers#10){.+.+.+}, at: [<ffffffff803d829f>] mnt_want_write+0x1f/0x50
#1: (&sb->s_type->i_mutex_key#15){+.+...}, at: [<ffffffff803dda27>] vfs_setxattr+0x57/0xb0
#2: (&ei->xattr_sem){++++..}, at: [<ffffffff80489500>] ext4_xattr_set_handle+0xa0/0x5d0
stack backtrace:
CPU: 0 PID: 1894 Comm: python Not tainted 4.11.0-rc8+ #402
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
dump_stack+0x67/0x99
__lock_acquire+0x5f3/0x1830
lock_acquire+0xb5/0x1d0
down_read+0x2f/0x60
ext4_xattr_get+0x66/0x270
ext4_get_acl+0x43/0x1e0
get_acl+0x72/0xf0
posix_acl_create+0x5e/0x170
ext4_init_acl+0x21/0xc0
__ext4_new_inode+0xffd/0x16b0
ext4_xattr_set_entry+0x5ea/0xb70
ext4_xattr_block_set+0x1b5/0x970
ext4_xattr_set_handle+0x351/0x5d0
ext4_xattr_set+0x124/0x180
ext4_xattr_user_set+0x34/0x40
__vfs_setxattr+0x66/0x80
__vfs_setxattr_noperm+0x69/0x1c0
vfs_setxattr+0xa2/0xb0
setxattr+0x129/0x160
path_setxattr+0x87/0xb0
SyS_setxattr+0xf/0x20
entry_SYSCALL_64_fastpath+0x18/0xad
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Setting a large xattr value may require writing the attribute contents
to an external inode. In this case we may need to lock the xattr inode
along with the parent inode. This doesn't pose a deadlock risk because
xattr inodes are not directly visible to the user and their access is
restricted.
Assign a lockdep subclass to xattr inode's lock.
============================================
WARNING: possible recursive locking detected
4.12.0-rc1+ #740 Not tainted
--------------------------------------------
python/1822 is trying to acquire lock:
(&sb->s_type->i_mutex_key#15){+.+...}, at: [<ffffffff804912ca>] ext4_xattr_set_entry+0x65a/0x7b0
but task is already holding lock:
(&sb->s_type->i_mutex_key#15){+.+...}, at: [<ffffffff803d6687>] vfs_setxattr+0x57/0xb0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&sb->s_type->i_mutex_key#15);
lock(&sb->s_type->i_mutex_key#15);
*** DEADLOCK ***
May be due to missing lock nesting notation
4 locks held by python/1822:
#0: (sb_writers#10){.+.+.+}, at: [<ffffffff803d0eef>] mnt_want_write+0x1f/0x50
#1: (&sb->s_type->i_mutex_key#15){+.+...}, at: [<ffffffff803d6687>] vfs_setxattr+0x57/0xb0
#2: (jbd2_handle){.+.+..}, at: [<ffffffff80493f40>] start_this_handle+0xf0/0x420
#3: (&ei->xattr_sem){++++..}, at: [<ffffffff804920ba>] ext4_xattr_set_handle+0x9a/0x4f0
stack backtrace:
CPU: 0 PID: 1822 Comm: python Not tainted 4.12.0-rc1+ #740
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
dump_stack+0x67/0x9e
__lock_acquire+0x5f3/0x1750
lock_acquire+0xb5/0x1d0
down_write+0x2c/0x60
ext4_xattr_set_entry+0x65a/0x7b0
ext4_xattr_block_set+0x1b2/0x9b0
ext4_xattr_set_handle+0x322/0x4f0
ext4_xattr_set+0x144/0x1a0
ext4_xattr_user_set+0x34/0x40
__vfs_setxattr+0x66/0x80
__vfs_setxattr_noperm+0x69/0x1c0
vfs_setxattr+0xa2/0xb0
setxattr+0x12e/0x150
path_setxattr+0x87/0xb0
SyS_setxattr+0xf/0x20
entry_SYSCALL_64_fastpath+0x18/0xad
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Large xattr support is implemented for EXT4_FEATURE_INCOMPAT_EA_INODE.
If the size of an xattr value is larger than will fit in a single
external block, then the xattr value will be saved into the body
of an external xattr inode.
The also helps support a larger number of xattr, since only the headers
will be stored in the in-inode space or the single external block.
The inode is referenced from the xattr header via "e_value_inum",
which was formerly "e_value_block", but that field was never used.
The e_value_size still contains the xattr size so that listing
xattrs does not need to look up the inode if the data is not accessed.
struct ext4_xattr_entry {
__u8 e_name_len; /* length of name */
__u8 e_name_index; /* attribute name index */
__le16 e_value_offs; /* offset in disk block of value */
__le32 e_value_inum; /* inode in which value is stored */
__le32 e_value_size; /* size of attribute value */
__le32 e_hash; /* hash value of name and value */
char e_name[0]; /* attribute name */
};
The xattr inode is marked with the EXT4_EA_INODE_FL flag and also
holds a back-reference to the owning inode in its i_mtime field,
allowing the ext4/e2fsck to verify the correct inode is accessed.
[ Applied fix by Dan Carpenter to avoid freeing an ERR_PTR. ]
Lustre-Jira: https://jira.hpdd.intel.com/browse/LU-80
Lustre-bugzilla: https://bugzilla.lustre.org/show_bug.cgi?id=4424
Signed-off-by: Kalpak Shah <kalpak.shah@sun.com>
Signed-off-by: James Simmons <uja.ornl@gmail.com>
Signed-off-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
This INCOMPAT_LARGEDIR feature allows larger directories to be created
in ldiskfs, both with directory sizes over 2GB and and a maximum htree
depth of 3 instead of the current limit of 2. These features are needed
in order to exceed the current limit of approximately 10M entries in a
single directory.
This patch was originally written by Yang Sheng to support the Lustre server.
[ Bumped the credits needed to update an indexed directory -- tytso ]
Signed-off-by: Liang Zhen <liang.zhen@intel.com>
Signed-off-by: Yang Sheng <yang.sheng@intel.com>
Signed-off-by: Artem Blagodarenko <artem.blagodarenko@seagate.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Two entries being added at the same time to the IFLA
policy table, whilst parallel bug fixes to decnet
routing dst handling overlapping with the dst gc removal
in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull more ufs fixes from Al Viro:
"More UFS fixes, unfortunately including build regression fix for the
64-bit s_dsize commit. Fixed in this pile:
- trivial bug in signedness of 32bit timestamps on ufs1
- ESTALE instead of ufs_error() when doing open-by-fhandle on
something deleted
- build regression on 32bit in ufs_new_fragments() - calculating that
many percents of u64 pulls libgcc stuff on some of those. Mea
culpa.
- fix hysteresis loop broken by typo in 2.4.14.7 (right next to the
location of previous bug).
- fix the insane limits of said hysteresis loop on filesystems with
very low percentage of reserved blocks. If it's 5% or less, just
use the OPTSPACE policy.
- calculate those limits once and mount time.
This tree does pass xfstests clean (both ufs1 and ufs2) and it _does_
survive cross-builds.
Again, my apologies for missing that, especially since I have noticed
a related percentage-of-64bit issue in earlier patches (when dealing
with amount of reserved blocks). Self-LART applied..."
* 'ufs-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ufs: fix the logics for tail relocation
ufs_iget(): fail with -ESTALE on deleted inode
fix signedness of timestamps on ufs1
Call verify_dir_item before memcmp_extent_buffer reading name from
dir_item.
Signed-off-by: Su Yue <suy.fnst@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
btrfs_del_root_ref calls btrfs_search_slot and reads name from root_ref.
Call btrfs_is_name_len_valid before memcmp.
Signed-off-by: Su Yue <suy.fnst@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
In btrfs_get_name, there's btrfs_search_slot and reads name from
inode_ref/root_ref.
Call btrfs_is_name_len_valid in btrfs_get_name.
Signed-off-by: Su Yue <suy.fnst@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Since iterate_dir_item checks name_len in its own way,
so use btrfs_is_name_len_valid not 'verify_dir_item' to make more strict
name_len check.
Signed-off-by: Su Yue <suy.fnst@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ switched ENAMETOOLONG to EIO ]
Signed-off-by: David Sterba <dsterba@suse.com>
In btrfs_log_inode, btrfs_search_forward gets the buffer and then
btrfs_check_ref_name_override will read name from ref/extref for the
first time.
Call btrfs_is_name_len_valid before reading name.
Signed-off-by: Su Yue <suy.fnst@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
replay_xattr_deletes calls btrfs_search_slot to get buffer and reads
name.
Call verify_dir_item to check name_len in replay_xattr_deletes to avoid
reading out of boundary.
Signed-off-by: Su Yue <suy.fnst@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
replay_one_buffer first reads buffers and dispatches items accroding to
the item type.
In this patch, add_inode_ref handles inode_ref and inode_extref.
Then add_inode_ref calls ref_get_fields and extref_get_fields to read
ref/extref name for the first time.
So checking name_len before reading those two is fine.
add_inode_ref also calls inode_in_dir to match ref/extref in parent_dir.
The call graph includes btrfs_match_dir_item_name to read dir_item name
in the parent dir.
Checking first dir_item is not enough. Change it to verify every
dir_item while doing matches.
Signed-off-by: Su Yue <suy.fnst@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Introduce function btrfs_is_name_len_valid.
The function compares parameter @name_len with item boundary then
returns true if name_len is valid.
Signed-off-by: Su Yue <suy.fnst@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ s/btrfs_leaf_data/BTRFS_LEAF_DATA_OFFSET/ ]
Signed-off-by: David Sterba <dsterba@suse.com>
We should really just wait in wait_dev_flush and let the caller decide
what to do with the error value.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Similar to what submit_bio_wait does, we should account for IO while
waiting for a bio completion. This has marginal visible effects, flush
bio is short-lived.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
For devices that support flushing, we allocate a bio, submit, wait for
it and then free it. The bio allocation does not fail so ENOMEM is not a
problem but we still may unnecessarily stress the allocation subsystem.
Instead, we can allocate the bio at the same time we allocate the device
and reuse it each time we need to flush the barriers. The bio is reset
before each use. Reference counting is simplified to just device
allocation (get) and freeing (put).
The bio used to be submitted through the integrity checker which will
find out that bio has no data attached and call submit_bio.
Status of the bio in flight needs to be tracked separately in case the
device caches get switched off between write and wait.
Signed-off-by: David Sterba <dsterba@suse.com>
An incremental send can contain unlink operations with an invalid target
path when we rename some directory inode A, then rename some file inode B
to the old name of inode A and directory inode A is an ancestor of inode B
in the parent snapshot (but not anymore in the send snapshot).
Consider the following example scenario where this issue happens.
Parent snapshot:
. (ino 256)
|
|--- dir1/ (ino 257)
|--- dir2/ (ino 258)
| |--- file1 (ino 259)
| |--- file3 (ino 261)
|
|--- dir3/ (ino 262)
|--- file22 (ino 260)
|--- dir4/ (ino 263)
Send snapshot:
. (ino 256)
|
|--- dir1/ (ino 257)
|--- dir2/ (ino 258)
|--- dir3 (ino 260)
|--- file3/ (ino 262)
|--- dir4/ (ino 263)
|--- file11 (ino 269)
|--- file33 (ino 261)
When attempting to apply the corresponding incremental send stream, an
unlink operation contains an invalid path which makes the receiver fail.
The following is verbose output of the btrfs receive command:
receiving snapshot snap2 uuid=7d5450da-a573-e043-a451-ec85f4879f0f (...)
utimes
utimes dir1
utimes dir1/dir2
link dir1/dir3/dir4/file11 -> dir1/dir2/file1
unlink dir1/dir2/file1
utimes dir1/dir2
truncate dir1/dir3/dir4/file11 size=0
utimes dir1/dir3/dir4/file11
rename dir1/dir3 -> o262-7-0
link dir1/dir3 -> o262-7-0/file22
unlink dir1/dir3/file22
ERROR: unlink dir1/dir3/file22 failed. Not a directory
The following steps happen during the computation of the incremental send
stream the lead to this issue:
1) Before we start processing the new and deleted references for inode
260, we compute the full path of the deleted reference
("dir1/dir3/file22") and cache it in the list of deleted references
for our inode.
2) We then start processing the new references for inode 260, for which
there is only one new, located at "dir1/dir3". When processing this
new reference, we check that inode 262, which was not yet processed,
collides with the new reference and because of that we orphanize
inode 262 so its new full path becomes "o262-7-0".
3) After the orphanization of inode 262, we create the new reference for
inode 260 by issuing a link command with a target path of "dir1/dir3"
and a source path of "o262-7-0/file22".
4) We then start processing the deleted references for inode 260, for
which there is only one with the base name of "file22", and issue
an unlink operation containing the target path computed at step 1,
which is wrong because that path no longer exists and should be
replaced with "o262-7-0/file22".
So fix this issue by recomputing the full path of deleted references if
when we processed the new references for an inode we ended up orphanizing
any other inode that is an ancestor of our inode in the parent snapshot.
A test case for fstests follows soon.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
[ adjusted after prev patch removed fs_path::dir_path and dir_path_len ]
Signed-off-by: David Sterba <dsterba@suse.com>
Currently an incremental snapshot can generate link operations which
contain an invalid target path. Such case happens when in the send
snapshot a file was renamed, a new hard link added for it and some
other inode (with a lower number) got renamed to the former name of
that file. Example:
Parent snapshot
. (ino 256)
|
|--- f1 (ino 257)
|--- f2 (ino 258)
|--- f3 (ino 259)
Send snapshot
. (ino 256)
|
|--- f2 (ino 257)
|--- f3 (ino 258)
|--- f4 (ino 259)
|--- f5 (ino 258)
The following steps happen when computing the incremental send stream:
1) When processing inode 257, inode 258 is orphanized (renamed to
"o258-7-0"), because its current reference has the same name as the
new reference for inode 257;
2) When processing inode 258, we iterate over all its new references,
which have the names "f3" and "f5". The first iteration sees name
"f5" and renames the inode from its orphan name ("o258-7-0") to
"f5", while the second iteration sees the name "f3" and, incorrectly,
issues a link operation with a target name matching the orphan name,
which no longer exists. The first iteration had reset the current
valid path of the inode to "f5", but in the second iteration we lost
it because we found another inode, with a higher number of 259, which
has a reference named "f3" as well, so we orphanized inode 259 and
recomputed the current valid path of inode 258 to its old orphan
name because inode 259 could be an ancestor of inode 258 and therefore
the current valid path could contain the pre-orphanization name of
inode 259. However in this case inode 259 is not an ancestor of inode
258 so the current valid path should not be recomputed.
This makes the receiver fail with the following error:
ERROR: link f3 -> o258-7-0 failed: No such file or directory
So fix this by not recomputing the current valid path for an inode
whenever we find a colliding reference from some not yet processed inode
(inode number higher then the one currently being processed), unless
that other inode is an ancestor of the one we are currently processing.
A test case for fstests will follow soon.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
While punching a hole in a range that is not aligned with the sector size
(currently the same as the page size) we can end up leaving an extent map
in memory with a length that is smaller then the sector size or with a
start offset that is not aligned to the sector size. Both cases are not
expected and can lead to problems. This issue is easily detected
after the patch from commit a7e3b975a0 ("Btrfs: fix reported number of
inode blocks"), introduced in kernel 4.12-rc1, in a scenario like the
following for example:
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt
$ xfs_io -c "pwrite -S 0xaa -b 100K 0 100K" /mnt/foo
$ xfs_io -c "fpunch 60K 90K" /mnt/foo
$ xfs_io -c "pwrite -S 0xbb -b 100K 50K 100K" /mnt/foo
$ xfs_io -c "pwrite -S 0xcc -b 50K 100K 50K" /mnt/foo
$ umount /mnt
After the unmount operation we can see several warnings emmitted due to
underflows related to space reservation counters:
[ 2837.443299] ------------[ cut here ]------------
[ 2837.447395] WARNING: CPU: 8 PID: 2474 at fs/btrfs/inode.c:9444 btrfs_destroy_inode+0xe8/0x27e [btrfs]
[ 2837.452108] Modules linked in: dm_flakey dm_mod ppdev parport_pc psmouse parport sg pcspkr acpi_cpufreq tpm_tis tpm_tis_core i2c_piix4 i2c_core evdev tpm button se
rio_raw sunrpc loop autofs4 ext4 crc16 jbd2 mbcache btrfs raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c crc32c_gene
ric raid1 raid0 multipath linear md_mod sr_mod cdrom sd_mod ata_generic virtio_scsi ata_piix libata virtio_pci virtio_ring virtio e1000 scsi_mod floppy
[ 2837.458389] CPU: 8 PID: 2474 Comm: umount Tainted: G W 4.10.0-rc8-btrfs-next-43+ #1
[ 2837.459754] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.1-0-gb3ef39f-prebuilt.qemu-project.org 04/01/2014
[ 2837.462379] Call Trace:
[ 2837.462379] dump_stack+0x68/0x92
[ 2837.462379] __warn+0xc2/0xdd
[ 2837.462379] warn_slowpath_null+0x1d/0x1f
[ 2837.462379] btrfs_destroy_inode+0xe8/0x27e [btrfs]
[ 2837.462379] destroy_inode+0x3d/0x55
[ 2837.462379] evict+0x177/0x17e
[ 2837.462379] dispose_list+0x50/0x71
[ 2837.462379] evict_inodes+0x132/0x141
[ 2837.462379] generic_shutdown_super+0x3f/0xeb
[ 2837.462379] kill_anon_super+0x12/0x1c
[ 2837.462379] btrfs_kill_super+0x16/0x21 [btrfs]
[ 2837.462379] deactivate_locked_super+0x30/0x68
[ 2837.462379] deactivate_super+0x36/0x39
[ 2837.462379] cleanup_mnt+0x58/0x76
[ 2837.462379] __cleanup_mnt+0x12/0x14
[ 2837.462379] task_work_run+0x77/0x9b
[ 2837.462379] prepare_exit_to_usermode+0x9d/0xc5
[ 2837.462379] syscall_return_slowpath+0x196/0x1b9
[ 2837.462379] entry_SYSCALL_64_fastpath+0xab/0xad
[ 2837.462379] RIP: 0033:0x7f3ef3e6b9a7
[ 2837.462379] RSP: 002b:00007ffdd0d8de58 EFLAGS: 00000246 ORIG_RAX: 00000000000000a6
[ 2837.462379] RAX: 0000000000000000 RBX: 0000556f76a39060 RCX: 00007f3ef3e6b9a7
[ 2837.462379] RDX: 0000000000000001 RSI: 0000000000000000 RDI: 0000556f76a3f910
[ 2837.462379] RBP: 0000556f76a3f910 R08: 0000556f76a3e670 R09: 0000000000000015
[ 2837.462379] R10: 00000000000006b4 R11: 0000000000000246 R12: 00007f3ef436ce64
[ 2837.462379] R13: 0000000000000000 R14: 0000556f76a39240 R15: 00007ffdd0d8e0e0
[ 2837.519355] ---[ end trace e79345fe24b30b8d ]---
[ 2837.596256] ------------[ cut here ]------------
[ 2837.597625] WARNING: CPU: 8 PID: 2474 at fs/btrfs/extent-tree.c:5699 btrfs_free_block_groups+0x246/0x3eb [btrfs]
[ 2837.603547] Modules linked in: dm_flakey dm_mod ppdev parport_pc psmouse parport sg pcspkr acpi_cpufreq tpm_tis tpm_tis_core i2c_piix4 i2c_core evdev tpm button serio_raw sunrpc loop autofs4 ext4 crc16 jbd2 mbcache btrfs raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c crc32c_generic raid1 raid0 multipath linear md_mod sr_mod cdrom sd_mod ata_generic virtio_scsi ata_piix libata virtio_pci virtio_ring virtio e1000 scsi_mod floppy
[ 2837.659372] CPU: 8 PID: 2474 Comm: umount Tainted: G W 4.10.0-rc8-btrfs-next-43+ #1
[ 2837.663359] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.1-0-gb3ef39f-prebuilt.qemu-project.org 04/01/2014
[ 2837.663359] Call Trace:
[ 2837.663359] dump_stack+0x68/0x92
[ 2837.663359] __warn+0xc2/0xdd
[ 2837.663359] warn_slowpath_null+0x1d/0x1f
[ 2837.663359] btrfs_free_block_groups+0x246/0x3eb [btrfs]
[ 2837.663359] close_ctree+0x1dd/0x2e1 [btrfs]
[ 2837.663359] ? evict_inodes+0x132/0x141
[ 2837.663359] btrfs_put_super+0x15/0x17 [btrfs]
[ 2837.663359] generic_shutdown_super+0x6a/0xeb
[ 2837.663359] kill_anon_super+0x12/0x1c
[ 2837.663359] btrfs_kill_super+0x16/0x21 [btrfs]
[ 2837.663359] deactivate_locked_super+0x30/0x68
[ 2837.663359] deactivate_super+0x36/0x39
[ 2837.663359] cleanup_mnt+0x58/0x76
[ 2837.663359] __cleanup_mnt+0x12/0x14
[ 2837.663359] task_work_run+0x77/0x9b
[ 2837.663359] prepare_exit_to_usermode+0x9d/0xc5
[ 2837.663359] syscall_return_slowpath+0x196/0x1b9
[ 2837.663359] entry_SYSCALL_64_fastpath+0xab/0xad
[ 2837.663359] RIP: 0033:0x7f3ef3e6b9a7
[ 2837.663359] RSP: 002b:00007ffdd0d8de58 EFLAGS: 00000246 ORIG_RAX: 00000000000000a6
[ 2837.663359] RAX: 0000000000000000 RBX: 0000556f76a39060 RCX: 00007f3ef3e6b9a7
[ 2837.663359] RDX: 0000000000000001 RSI: 0000000000000000 RDI: 0000556f76a3f910
[ 2837.663359] RBP: 0000556f76a3f910 R08: 0000556f76a3e670 R09: 0000000000000015
[ 2837.663359] R10: 00000000000006b4 R11: 0000000000000246 R12: 00007f3ef436ce64
[ 2837.663359] R13: 0000000000000000 R14: 0000556f76a39240 R15: 00007ffdd0d8e0e0
[ 2837.739445] ---[ end trace e79345fe24b30b8e ]---
[ 2837.745595] ------------[ cut here ]------------
[ 2837.746412] WARNING: CPU: 8 PID: 2474 at fs/btrfs/extent-tree.c:5700 btrfs_free_block_groups+0x261/0x3eb [btrfs]
[ 2837.747955] Modules linked in: dm_flakey dm_mod ppdev parport_pc psmouse parport sg pcspkr acpi_cpufreq tpm_tis tpm_tis_core i2c_piix4 i2c_core evdev tpm button serio_raw sunrpc loop autofs4 ext4 crc16 jbd2 mbcache btrfs raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c crc32c_generic raid1 raid0 multipath linear md_mod sr_mod cdrom sd_mod ata_generic virtio_scsi ata_piix libata virtio_pci virtio_ring virtio e1000 scsi_mod floppy
[ 2837.755395] CPU: 8 PID: 2474 Comm: umount Tainted: G W 4.10.0-rc8-btrfs-next-43+ #1
[ 2837.756769] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.1-0-gb3ef39f-prebuilt.qemu-project.org 04/01/2014
[ 2837.758526] Call Trace:
[ 2837.758925] dump_stack+0x68/0x92
[ 2837.759383] __warn+0xc2/0xdd
[ 2837.759383] warn_slowpath_null+0x1d/0x1f
[ 2837.759383] btrfs_free_block_groups+0x261/0x3eb [btrfs]
[ 2837.759383] close_ctree+0x1dd/0x2e1 [btrfs]
[ 2837.759383] ? evict_inodes+0x132/0x141
[ 2837.759383] btrfs_put_super+0x15/0x17 [btrfs]
[ 2837.759383] generic_shutdown_super+0x6a/0xeb
[ 2837.759383] kill_anon_super+0x12/0x1c
[ 2837.759383] btrfs_kill_super+0x16/0x21 [btrfs]
[ 2837.759383] deactivate_locked_super+0x30/0x68
[ 2837.759383] deactivate_super+0x36/0x39
[ 2837.759383] cleanup_mnt+0x58/0x76
[ 2837.759383] __cleanup_mnt+0x12/0x14
[ 2837.759383] task_work_run+0x77/0x9b
[ 2837.759383] prepare_exit_to_usermode+0x9d/0xc5
[ 2837.759383] syscall_return_slowpath+0x196/0x1b9
[ 2837.759383] entry_SYSCALL_64_fastpath+0xab/0xad
[ 2837.759383] RIP: 0033:0x7f3ef3e6b9a7
[ 2837.759383] RSP: 002b:00007ffdd0d8de58 EFLAGS: 00000246 ORIG_RAX: 00000000000000a6
[ 2837.759383] RAX: 0000000000000000 RBX: 0000556f76a39060 RCX: 00007f3ef3e6b9a7
[ 2837.759383] RDX: 0000000000000001 RSI: 0000000000000000 RDI: 0000556f76a3f910
[ 2837.759383] RBP: 0000556f76a3f910 R08: 0000556f76a3e670 R09: 0000000000000015
[ 2837.759383] R10: 00000000000006b4 R11: 0000000000000246 R12: 00007f3ef436ce64
[ 2837.759383] R13: 0000000000000000 R14: 0000556f76a39240 R15: 00007ffdd0d8e0e0
[ 2837.777063] ---[ end trace e79345fe24b30b8f ]---
[ 2837.778235] ------------[ cut here ]------------
[ 2837.778856] WARNING: CPU: 8 PID: 2474 at fs/btrfs/extent-tree.c:9825 btrfs_free_block_groups+0x348/0x3eb [btrfs]
[ 2837.791385] Modules linked in: dm_flakey dm_mod ppdev parport_pc psmouse parport sg pcspkr acpi_cpufreq tpm_tis tpm_tis_core i2c_piix4 i2c_core evdev tpm button serio_raw sunrpc loop autofs4 ext4 crc16 jbd2 mbcache btrfs raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c crc32c_generic raid1 raid0 multipath linear md_mod sr_mod cdrom sd_mod ata_generic virtio_scsi ata_piix libata virtio_pci virtio_ring virtio e1000 scsi_mod floppy
[ 2837.797711] CPU: 8 PID: 2474 Comm: umount Tainted: G W 4.10.0-rc8-btrfs-next-43+ #1
[ 2837.798594] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.1-0-gb3ef39f-prebuilt.qemu-project.org 04/01/2014
[ 2837.800118] Call Trace:
[ 2837.800515] dump_stack+0x68/0x92
[ 2837.801015] __warn+0xc2/0xdd
[ 2837.801471] warn_slowpath_null+0x1d/0x1f
[ 2837.801698] btrfs_free_block_groups+0x348/0x3eb [btrfs]
[ 2837.801698] close_ctree+0x1dd/0x2e1 [btrfs]
[ 2837.801698] ? evict_inodes+0x132/0x141
[ 2837.801698] btrfs_put_super+0x15/0x17 [btrfs]
[ 2837.801698] generic_shutdown_super+0x6a/0xeb
[ 2837.801698] kill_anon_super+0x12/0x1c
[ 2837.801698] btrfs_kill_super+0x16/0x21 [btrfs]
[ 2837.801698] deactivate_locked_super+0x30/0x68
[ 2837.801698] deactivate_super+0x36/0x39
[ 2837.801698] cleanup_mnt+0x58/0x76
[ 2837.801698] __cleanup_mnt+0x12/0x14
[ 2837.801698] task_work_run+0x77/0x9b
[ 2837.801698] prepare_exit_to_usermode+0x9d/0xc5
[ 2837.801698] syscall_return_slowpath+0x196/0x1b9
[ 2837.801698] entry_SYSCALL_64_fastpath+0xab/0xad
[ 2837.801698] RIP: 0033:0x7f3ef3e6b9a7
[ 2837.801698] RSP: 002b:00007ffdd0d8de58 EFLAGS: 00000246 ORIG_RAX: 00000000000000a6
[ 2837.801698] RAX: 0000000000000000 RBX: 0000556f76a39060 RCX: 00007f3ef3e6b9a7
[ 2837.801698] RDX: 0000000000000001 RSI: 0000000000000000 RDI: 0000556f76a3f910
[ 2837.801698] RBP: 0000556f76a3f910 R08: 0000556f76a3e670 R09: 0000000000000015
[ 2837.801698] R10: 00000000000006b4 R11: 0000000000000246 R12: 00007f3ef436ce64
[ 2837.801698] R13: 0000000000000000 R14: 0000556f76a39240 R15: 00007ffdd0d8e0e0
[ 2837.818441] ---[ end trace e79345fe24b30b90 ]---
[ 2837.818991] BTRFS info (device sdc): space_info 1 has 7974912 free, is not full
[ 2837.819830] BTRFS info (device sdc): space_info total=8388608, used=417792, pinned=0, reserved=0, may_use=18446744073709547520, readonly=0
What happens in the above example is the following:
1) When punching the hole, at btrfs_punch_hole(), the variable tail_len
is set to 2048 (as tail_start is 148Kb + 1 and offset + len is 150Kb).
This results in the creation of an extent map with a length of 2Kb
starting at file offset 148Kb, through find_first_non_hole() ->
btrfs_get_extent().
2) The second write (first write after the hole punch operation), sets
the range [50Kb, 152Kb[ to delalloc.
3) The third write, at btrfs_find_new_delalloc_bytes(), sees the extent
map covering the range [148Kb, 150Kb[ and ends up calling
set_extent_bit() for the same range, which results in splitting an
existing extent state record, covering the range [148Kb, 152Kb[ into
two 2Kb extent state records, covering the ranges [148Kb, 150Kb[ and
[150Kb, 152Kb[.
4) Finally at lock_and_cleanup_extent_if_need(), immediately after calling
btrfs_find_new_delalloc_bytes() we clear the delalloc bit from the
range [100Kb, 152Kb[ which results in the btrfs_clear_bit_hook()
callback being invoked against the two 2Kb extent state records that
cover the ranges [148Kb, 150Kb[ and [150Kb, 152Kb[. When called against
the first 2Kb extent state, it calls btrfs_delalloc_release_metadata()
with a length argument of 2048 bytes. That function rounds up the length
to a sector size aligned length, so it ends up considering a length of
4096 bytes, and then calls calc_csum_metadata_size() which results in
decrementing the inode's csum_bytes counter by 4096 bytes, so after
it stays a value of 0 bytes. Then the same happens when
btrfs_clear_bit_hook() is called against the second extent state that
has a length of 2Kb, covering the range [150Kb, 152Kb[, the length is
rounded up to 4096 and calc_csum_metadata_size() ends up being called
to decrement 4096 bytes from the inode's csum_bytes counter, which
at that time has a value of 0, leading to an underflow, which is
exactly what triggers the first warning, at btrfs_destroy_inode().
All the other warnings relate to several space accounting counters
that underflow as well due to similar reasons.
A similar case but where the hole punching operation creates an extent map
with a start offset not aligned to the sector size is the following:
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt
$ xfs_io -f -c "fpunch 695K 820K" $SCRATCH_MNT/bar
$ xfs_io -c "pwrite -S 0xaa 1008K 307K" $SCRATCH_MNT/bar
$ xfs_io -c "pwrite -S 0xbb -b 630K 1073K 630K" $SCRATCH_MNT/bar
$ xfs_io -c "pwrite -S 0xcc -b 459K 1068K 459K" $SCRATCH_MNT/bar
$ umount /mnt
During the unmount operation we get similar traces for the same reasons as
in the first example.
So fix the hole punching operation to make sure it never creates extent
maps with a length that is not aligned to the sector size nor with a start
offset that is not aligned to the sector size, as this breaks all
assumptions and it's a land mine.
Fixes: d77815461f ("btrfs: Avoid trucating page or punching hole in a already existed hole.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
On an uncontended system, we can end up hitting soft lockups while
doing replace_path. At the core, and frequently called is
btrfs_qgroup_trace_leaf_items, so it makes sense to add a cond_resched
there.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This function is supposed to return blk_status_t error codes now but
there was a stray -ENOMEM left behind.
Fixes: 4e4cbee93d ("block: switch bios to blk_status_t")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: David Sterba <dsterba@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
'rc' is known to be 0 at this point. So if 'init_sg' or 'kzalloc' fails, we
should return -ENOMEM instead.
Also remove a useless 'rc' in a debug message as it is meaningless here.
Fixes: 026e93dc0a ("CIFS: Encrypt SMB3 requests before sending")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <smfrench@gmail.com>
CC: Stable <stable@vger.kernel.org>
Instead of explicitly calling scsi_req_init() after blk_get_request(),
call that function from inside blk_get_request(). Add an
.initialize_rq_fn() callback function to the block drivers that need
it. Merge the IDE .init_rq_fn() function into .initialize_rq_fn()
because it is too small to keep it as a separate function. Keep the
scsi_req_init() call in ide_prep_sense() because it follows a
blk_rq_init() call.
References: commit 82ed4db499 ("block: split scsi_request out of struct request")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is a redundant return in function cifs_creation_time_get
that appears to be old vestigial code than can be removed. So
remove it.
Detected by CoverityScan, CID#1361924 ("Structurally dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Downgrade the loglevel for SMB2 to prevent filling the log
with messages if e.g. readdir was interrupted. Also make SMB2
and SMB1 codepaths do the same logging during readdir.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <smfrench@gmail.com>
CC: Stable <stable@vger.kernel.org>
pages is being allocated however a null check on bv is being used
to see if the allocation failed. Fix this by checking if pages is
null.
Detected by CoverityScan, CID#1432974 ("Logically dead code")
Fixes: ccf7f4088a ("CIFS: Add asynchronous context to support kernel AIO")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <smfrench@gmail.com>
The current code causes a static checker warning because ITER_IOVEC is
zero so the condition is never true.
Fixes: 6685c5e2d1 ("CIFS: Add asynchronous read support through kernel AIO")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Currently, percpu_counter_add is a wrapper around __percpu_counter_add
which is preempt safe due to explicit calls to preempt_disable. Given
how __ prefix is used in percpu related interfaces, the naming
unfortunately creates the false sense that __percpu_counter_add is
less safe than percpu_counter_add. In terms of context-safety,
they're equivalent. The only difference is that the __ version takes
a batch parameter.
Make this a bit more explicit by just renaming __percpu_counter_add to
percpu_counter_add_batch.
This patch doesn't cause any functional changes.
tj: Minor updates to patch description for clarity. Cosmetic
indentation updates.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Chris Mason <clm@fb.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: David Sterba <dsterba@suse.com>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Jan Kara <jack@suse.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: linux-mm@kvack.org
Cc: "David S. Miller" <davem@davemloft.net>
bmap returns a dumb LBA address but not the block device that goes with
that LBA. Swapfiles don't care about this and will blindly assume that
the data volume is the correct blockdev, which is totally bogus for
files on the rt subvolume. This results in the swap code doing IOs to
arbitrary locations on the data device(!) if the passed in mapping is a
realtime file, so just turn off bmap for rt files.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Expose the readlink variant that doesn't take the inode lock so that
the scrubber can inspect symlink contents.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Teach the extended attribute reading functions to pass along a
transaction context if one was supplied. The extended attribute scrub
code will use transactions to lock buffers and avoid deadlocking with
itself in the case of loops; since it will already have the inode
locked, also create xattr get/list helpers that don't take locks.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Teach the directory reading functions to pass along a transaction context
if one was supplied. The directory scrub code will use transactions to
lock buffers and avoid deadlocking with itself in the case of loops.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Modify the existing dir leafn lasthash function to enable us to
calculate the highest hash value of a leaf1 block. This will be used by
the directory scrubbing code to check the sanity of hashes in leaf1
directory blocks.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Refactor the inode fork block counting function to count extents for us
at the same time. This will be used by the bmbt scrubber function.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
There is an inconsistency in the way that _bmap_count_blocks deals with
delalloc reservations -- if the specified fork is in extents format,
*count is set to the total number of blocks referenced by the in-core
fork, including delalloc extents. However, if the fork is in btree
format, *count is set to the number of blocks referenced by the on-disk
fork, which does /not/ include delalloc extents.
For the lone existing caller of _bmap_count_blocks this hasn't been an
issue because the function is only used to count xattr fork blocks
(where there aren't any delalloc reservations). However, when scrub
comes along it will use this same function to check di_nblocks against
both on-disk extent maps, so we need this behavior to be consistent.
Therefore, fix _bmap_count_leaves not to include delalloc extents and
remove unnecessary parameters.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Return EAGAIN if any of the following checks fail
+ i_rwsem is not lockable
+ NODATACOW or PREALLOC is not set
+ Cannot nocow at the desired location
+ Writing beyond end of file which is not allocated
Acked-by: David Sterba <dsterba@suse.com>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If IOCB_NOWAIT is set, bail if the i_rwsem is not lockable
immediately.
IF IOMAP_NOWAIT is set, return EAGAIN in xfs_file_iomap_begin
if it needs allocation either due to file extension, writing to a hole,
or COW or waiting for other DIOs to finish.
Return -EAGAIN if we don't have extent list in memory.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Return EAGAIN if any of the following checks fail for direct I/O:
+ i_rwsem is lockable
+ Writing beyond end of file (will trigger allocation)
+ Blocks are not allocated at the write location
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A new bio operation flag REQ_NOWAIT is introduced to identify bio's
orignating from iocb with IOCB_NOWAIT. This flag indicates
to return immediately if a request cannot be made instead
of retrying.
Stacked devices such as md (the ones with make_request_fn hooks)
currently are not supported because it may block for housekeeping.
For example, an md can have a part of the device suspended.
For this reason, only request based devices are supported.
In the future, this feature will be expanded to stacked devices
by teaching them how to handle the REQ_NOWAIT flags.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
IOCB_NOWAIT translates to IOMAP_NOWAIT for iomaps.
This is used by XFS in the XFS patch.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
RWF_NOWAIT informs kernel to bail out if an AIO request will block
for reasons such as file allocations, or a writeback triggered,
or would block while allocating requests while performing
direct I/O.
RWF_NOWAIT is translated to IOCB_NOWAIT for iocb->ki_flags.
FMODE_AIO_NOWAIT is a flag which identifies the file opened is capable
of returning -EAGAIN if the AIO call will block. This must be set by
supporting filesystems in the ->open() call.
Filesystems xfs, btrfs and ext4 would be supported in the following patches.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
aio_rw_flags is introduced in struct iocb (using aio_reserved1) which will
carry the RWF_* flags. We cannot use aio_flags because they are not
checked for validity which may break existing applications.
Note, the only place RWF_HIPRI comes in effect is dio_await_one().
All the rest of the locations, aio code return -EIOCBQUEUED before the
checks for RWF_HIPRI.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Also added RWF_SUPPORTED to encompass all flags.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We got an internal report about a file system not wanting to mount
following 99e3ecfcb9 ("Btrfs: add more validation checks for
superblock").
BTRFS error (device sdb1): super_total_bytes 1000203816960 mismatch with
fs_devices total_rw_bytes 1000203820544
Subtracting the numbers we get a difference of less than a 4kb. Upon
closer inspection it became apparent that mkfs actually rounds down the
size of the device to a multiple of sector size. However, the same
cannot be said for various functions which modify the total size and are
called from btrfs_balance as well as when adding a new device. So this
patch ensures that values being saved into on-disk data structures are
always rounded down to a multiple of sectorsize.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The device->total_bytes member needs to always be rounded down to sectorsize
so that it corresponds to the value of super->total_bytes. However, there are
multiple places where the setter is fed a value which is not rounded which
can cause a fs to be unmountable due to the check introduced in
99e3ecfcb9 ("Btrfs: add more validation checks for superblock"). This patch
implements the getter/setter manually so that in a later patch I can add
necessary code to catch offenders.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The mount option alloc_start was used in the past for debugging and
stressing the chunk allocator. Not meant to be used by users, so we're
not breaking anybody's setup.
There was some added complexity handling changes of the value and when
it was not same as default. Such code has likely been untested and I
think it's better to remove it.
This patch kills all use of alloc_start, and by doing that also fixes
a bug when alloc_size is set, potentially called from statfs:
in btrfs_calc_avail_data_space, traversing the list in RCU, the RCU
protection is temporarily dropped so btrfs_account_dev_extents_size can
be called and then RCU is locked again! Doing that inside
list_for_each_entry_rcu is just asking for trouble, but unlikely to be
observed in practice.
Signed-off-by: David Sterba <dsterba@suse.com>
We can keep the state among the other fs_info flags, there's no reason
why fs_frozen would need to be separate.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The pattern when err is used for function exit and ret is used for
return values of callees is not used here.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Instead of passing each start address into is_vmalloc_or_module_addr()
to decide whether it falls into either the VMALLOC or the MODULES region,
we can simply check the type field of the current kcore_list entry, since
it will be set to KCORE_VMALLOC based on exactly the same conditions.
As a bonus, when reading the KCORE_TEXT region on architectures that have
one, this will avoid using vread() on the region if it happens to intersect
with a KCORE_VMALLOC region. This is due the fact that the KCORE_TEXT
region is the first one to be added to the kcore region list.
Reported-by: Tan Xiaojun <tanxiaojun@huawei.com>
Tested-by: Tan Xiaojun <tanxiaojun@huawei.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
So I've noticed a number of instances where it was not obvious from the
code whether ->task_list was for a wait-queue head or a wait-queue entry.
Furthermore, there's a number of wait-queue users where the lists are
not for 'tasks' but other entities (poll tables, etc.), in which case
the 'task_list' name is actively confusing.
To clear this all up, name the wait-queue head and entry list structure
fields unambiguously:
struct wait_queue_head::task_list => ::head
struct wait_queue_entry::task_list => ::entry
For example, this code:
rqw->wait.task_list.next != &wait->task_list
... is was pretty unclear (to me) what it's doing, while now it's written this way:
rqw->wait.head.next != &wait->entry
... which makes it pretty clear that we are iterating a list until we see the head.
Other examples are:
list_for_each_entry_safe(pos, next, &x->task_list, task_list) {
list_for_each_entry(wq, &fence->wait.task_list, task_list) {
... where it's unclear (to me) what we are iterating, and during review it's
hard to tell whether it's trying to walk a wait-queue entry (which would be
a bug), while now it's written as:
list_for_each_entry_safe(pos, next, &x->head, entry) {
list_for_each_entry(wq, &fence->wait.head, entry) {
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The wait_bit*() types and APIs are mixed into wait.h, but they
are a pretty orthogonal extension of wait-queues.
Furthermore, only about 50 kernel files use these APIs, while
over 1000 use the regular wait-queue functionality.
So clean up the main wait.h by moving the wait-bit functionality
out of it, into a separate .h and .c file:
include/linux/wait_bit.h for types and APIs
kernel/sched/wait_bit.c for the implementation
Update all header dependencies.
This reduces the size of wait.h rather significantly, by about 30%.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Rename 'struct wait_bit_queue::wait' to ::wq_entry, to more clearly
name it as a wait-queue entry.
Propagate it to a couple of usage sites where the wait-bit-queue internals
are exposed.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Rename:
wait_queue_t => wait_queue_entry_t
'wait_queue_t' was always a slight misnomer: its name implies that it's a "queue",
but in reality it's a queue *entry*. The 'real' queue is the wait queue head,
which had to carry the name.
Start sorting this out by renaming it to 'wait_queue_entry_t'.
This also allows the real structure name 'struct __wait_queue' to
lose its double underscore and become 'struct wait_queue_entry',
which is the more canonical nomenclature for such data types.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Using get_random_u32 here is faster, more fitting of the use case, and
just as cryptographically secure. It also has the benefit of providing
better randomness at early boot, which is sometimes when this is used.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Steve French <sfrench@samba.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Separate the "clear reflink flag" function into one function that checks
if the flag is needed, and a second function that checks and clears the
flag. The inode scrub code will want to check the necessity of the flag
without clearing it.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Adapt _reflink_find_shared to take an optional transaction pointer. The
inode scrubber code will need to decide (within transaction context) if
a file has shared blocks. To avoid buffer deadlocks, we must pass the
tp through to this function's utility calls.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Check the inode cache for a particular inode number. If it's in the
cache, check that it's not currently being reclaimed. If it's not being
reclaimed, return zero if the inode is allocated. This function will be
used by various scrubbers to decide if the cache is more up to date
than the disk in terms of checking if an inode is allocated.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Create a function to extract an in-core inobt record from a generic
btree_rec union so that scrub will be able to check inobt records
and check inode block alignment.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Plumb in the pieces (init_high_key, diff_two_keys) necessary to call
query_range on the inode space and block mapping btrees and to extract
raw btree records. This will eventually be used by the inobt and bmbt
scrubbers.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Export various internal functions so that the online scrubber can use
them to check the state of metadata.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
The btree record and key inorder check functions will be used by the
btree scrubber code, so make sure they're always built.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
This is a purely mechanical patch that removes the private
__{u,}int{8,16,32,64}_t typedefs in favor of using the system
{u,}int{8,16,32,64}_t typedefs. This is the sed script used to perform
the transformation and fix the resulting whitespace and indentation
errors:
s/typedef\t__uint8_t/typedef __uint8_t\t/g
s/typedef\t__uint/typedef __uint/g
s/typedef\t__int\([0-9]*\)_t/typedef int\1_t\t/g
s/__uint8_t\t/__uint8_t\t\t/g
s/__uint/uint/g
s/__int\([0-9]*\)_t\t/__int\1_t\t\t/g
s/__int/int/g
/^typedef.*int[0-9]*_t;$/d
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Don't bother wandering our way through the leaf nodes when the caller
issues a query_all; just zoom down the left side of the tree and walk
rightwards along level zero.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
The function is called from ioctl context and we don't hold any locks
that take part in writeback. Right now it's only fs_info::volume_mutex.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We don't hold any locks here. Inidirectly called from statfs.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Submit and wait parts of write_dev_flush() can be split into two
separate functions for better readability.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There is no extra benefit to count null bdev during the submit loop,
as these null devices will be anyway checked during command
completion device loop just after the submit loop. We are holding the
device_list_mutex, the device->bdev status won't change in between.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Since commit "btrfs: btrfs_io_bio_alloc never fails, skip error handling"
write_dev_flush will not return ENOMEM in the sending part. We do not
need to check for it in the callers.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ updated changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
We already skip storing data where compression does not make the result
at least one byte less. Let's make the logic better and check
that compression frees at least one sector size of bytes, otherwise it's
not that useful.
Signed-off-by: Timofey Titovets <nefelim4ag@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ changelog updated ]
Signed-off-by: David Sterba <dsterba@suse.com>
We can hardcode GFP_NOFS to btrfs_io_bio_alloc, although it means we
change it back from GFP_KERNEL in scrub. I'd rather save a few stack
bytes from not passing the gfp flags in the remaining, more imporatant,
contexts and the bio allocating API now looks more consistent.
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We use btrfs_bioset for bios and ask to allocate the entire size of
btrfs_io_bio from btrfs bio_alloc_bioset. The member 'bio' is
initialized but the bytes from 0 to offset of 'bio' are left
uninitialized. Although we initialize some of the members in our
helpers, we should initialize the whole structures.
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Currently dio read also goes to verify checksum if -EIO has been returned,
although it usually fails on checksum, it's not necessary at all, we could
directly check if there is another copy to read.
And with this, the behavior of dio read is now consistent with that of
buffered read.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ use bool for uptodate ]
Signed-off-by: David Sterba <dsterba@suse.com>
With raid1 profile, dio read isn't tolerating IO errors if read length is
less than the stripe length (64K).
Our bio didn't get split in btrfs_submit_direct_hook() if (dip->flags &
BTRFS_DIO_ORIG_BIO_SUBMITTED) is true and that happens when the read
length is less than 64k. In this case, if the underlying device returns
error somehow, bio->bi_error has recorded that error.
If we could recover the correct data from another copy in profile raid1/10/5/6,
with btrfs_subio_endio_read() returning 0, bio would have the correct data in
its vector, but bio->bi_error is not updated accordingly so that the following
dio_end_io(dio_bio, bio->bi_error) makes directIO think this read has failed.
This fixes the problem by setting bio's error to 0 if a good copy has been
found.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Most callers of btrfs_bio_alloc convert from bytes to sectors. Hide that
in the helper and simplify the logic in the callsers.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
compressed_bio_alloc is now a trivial wrapper around btrfs_bio_alloc, no
point keeping it. The error handling can be simplified, as we know
btrfs_bio_alloc will never fail.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
All callers pass gfp_flags=GFP_NOFS and nr_vecs=BIO_MAX_PAGES.
submit_extent_page adds __GFP_HIGH that does not make a difference in
our case as it allows access to memory reserves but otherwise does not
change the constraints.
Signed-off-by: David Sterba <dsterba@suse.com>
Update direct callers of btrfs_io_bio_alloc that do error handling, that
we can now remove.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Update direct callers of btrfs_bio_clone that do error handling, that we
can now remove.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Update direct callers of btrfs_bio_alloc that do error handling, that we
can now remove.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Christoph pointed out that bio allocations backed by a bioset will never
fail. As we always use a bioset for all bio allocations, we can skip
the error handling. This patch adjusts our low-level helpers, the
cascaded changes to all callers will come next.
CC: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The compression workspace buffers are larger than a page so we use
vmalloc, unconditionally. This is not always necessary as there might be
contiguous memory available.
Let's use the kvmalloc helpers that will try kmalloc first and fallback
to vmalloc. For that they require GFP_KERNEL flags. As we now have the
alloc_workspace calls protected by memalloc_nofs in the critical
contexts, we can safely use GFP_KERNEL.
Signed-off-by: David Sterba <dsterba@suse.com>
As alloc_workspace is now protected by memalloc_nofs where needed,
we can switch the kmalloc to use GFP_KERNEL.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The workspaces are preallocated at the beginning where we can safely use
GFP_KERNEL, but in some cases the find_workspace might reach the
allocation again, now in a more restricted context when the bios or
pages are being compressed.
To avoid potential lockup when alloc_workspace -> vmalloc would silently
use the GFP_KERNEL, add the memalloc_nofs helpers around the critical
call site.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
As we don't use vmalloc/vzalloc/vfree directly in ctree.c, we can now
use the proper header that defines kvmalloc.
Signed-off-by: David Sterba <dsterba@suse.com>
Now that init_ipath is called either from a safe context or with
memalloc_nofs protection, we can switch to GFP_KERNEL allocations in
init_path and init_data_container.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
init_ipath is called from a safe ioctl context and from scrub when
printing an error. The protection is added for three reasons:
* init_data_container calls vmalloc and this does not work as expected
in the GFP_NOFS context, so this silently does GFP_KERNEL and might
deadlock in some cases
* keep the context constraint of GFP_NOFS, used by scrub
* we want to use GFP_KERNEL unconditionally inside init_ipath or its
callees
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We use a growing buffer for xattrs larger than a page size, at some
point vmalloc is unconditionally used for larger buffers. We can still
try to avoid it using the kvmalloc helper.
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The logic of kmalloc and vmalloc fallback is opencoded in
several places, we can now use the existing helper.
Signed-off-by: David Sterba <dsterba@suse.com>
Logic already skips if compression makes data bigger, let's sync lzo
with zlib and also return error if compressed size is equal to
input size.
Signed-off-by: Timofey Titovets <nefelim4ag@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
bio_io_error was introduced in the commit 4246a0b63b
("block: add a bi_error field to struct bio"), so use it to simplify
code.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
First, instead of open-coding the vmalloc() fallback, use the new
kvzalloc() helper. Second, use memalloc_nofs_{save,restore}() instead of
GFP_NOFS, as vmalloc() uses some GFP_KERNEL allocations internally which
could lead to deadlocks.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Observing the number of slab objects of btrfs_transaction, there's just
one active on an almost quiescent filesystem, and the number of objects
goes to about ten when sync is in progress. Then the nubmer goes down to
1. This matches the expectations of the transaction lifetime.
For such use the separate slab cache is not justified, as we do not
reuse objects frequently. For the shortlived transaction, the generic
slab (size 512) should be ok. We can optimistically expect that the 512
slabs are not all used (fragmentation) and there are free slots to take
when we do the allocation, compared to potentially allocating a whole new
page for the separate slab.
We'll lose the stats about the object use, which could be added later if
we really need them.
Signed-off-by: David Sterba <dsterba@suse.com>
The structure scrub_wr_ctx is not used anywhere just the scrub context,
we can move the members there. The tgtdev is renamed so it's more clear
that it belongs to the "wr" part.
Signed-off-by: David Sterba <dsterba@suse.com>
As we now have the node/block sizes in fs_info, we can use them and can
drop the local copies.
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Fix copy paste typo in debug message for lzo.c, lzo is not deflate.
Signed-off-by: Timofey Titovets <nefelim4ag@gmail.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Nothing checks its return value.
Is it safe to skip checking return value of btrfs_wait_tree_block_writeback?
Liu Bo: I think yes, it's used in walk_log_tree which is called in two
places, free_log_tree and log replay. For free_log_tree, it waits for
any running writeback of the extent buffer under freeing to finish in
case we need to access the eb pointer from page->private, and it's OK to
not check the return value, while for log replay, it's doesn't wait
because wc->wait is not set. So neither cares about the writeback error.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
[ added more explanation to changelog, from Liu Bo ]
Signed-off-by: David Sterba <dsterba@suse.com>
__BTRFS_LAF_DATA_SIZE is used only by BTRFS_LEAF_DATA_SIZE. Make the
latter subsume the former.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Commit 5f39d397df ("Btrfs: Create extent_buffer interface
for large blocksizes") refactored btrfs_leaf_data function to take
extent_buffer rather than struct btrfs_leaf. However, as it turns out the
parameter being passed is never used. Furthermore this function no longer
returns the leaf data but rather the offset to it. So rename the function
to BTRFS_LEAF_DATA_OFFSET to make it consistent with other BTRFS_LEAF_*
helpers and turn it into a macro.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
[ removed () from the macro ]
Signed-off-by: David Sterba <dsterba@suse.com>
struct compressed_bio pointer can be used instead.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Instead of sending each argument of struct compressed_bio, send
the compressed_bio itself.
Also by having struct compressed_bio in btrfs_decompress_bio()
it would help tracing.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Following the factoring out of the creation code udpate_space_info can
only be called for already-existing space_info structs. As such it
cannot fail. Remove superfluous error handling and make the function
return void.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Currently the struct space_info creation code is intermixed in the
udpate_space_info function. There are well-defined points at which the
we actually want to create brand-new space_info structs (e.g. during
mount of the filesystem as well as sometimes when adding/initialising
new chunks). In such cases update_space_info is called with 0 as the
bytes parameter. All of this makes for spaghetti code.
Fix it by factoring out the creation code in a separate
create_space_info structure. This also allows to simplify the internals.
Also remove BUG_ON from do_alloc_chunk since the callers handle errors.
Furthermore it will make the update_space_info function not fail,
allowing us to remove error handling in callers. This will come in a
follow up patch.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This adds chunk_objectid and flags, with flags we can recognize whether
the block group is about data or metadata.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We commit transaction in order to reclaim space from pinned bytes because
it could process delayed refs, and in may_commit_transaction(), we check
first if pinned bytes are enough for the required space, we then check if
that plus bytes reserved for delayed insert are enough for the required
space.
This changes the code to the above logic.
Fixes: b150a4f10d ("Btrfs: use a percpu to keep track of possibly pinned bytes")
Tested-by: Nikolay Borisov <nborisov@suse.com>
Reported-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We don't need to take the mutex and zero out wr_cur_bio, as this is
called after the scrub finished.
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The helper scrub_free_wr_ctx is used only once and fits into
scrub_free_ctx as it continues sctx shutdown, no need to keep it
separate.
Signed-off-by: David Sterba <dsterba@suse.com>
The helper scrub_setup_wr_ctx is used only once and fits into
scrub_setup_ctx as it continues intialization, no need to keep it
separate.
Signed-off-by: David Sterba <dsterba@suse.com>
can_overcommit using the root to determine the allocation profile
is the only use of a root in the call graph below reserve_metadata_bytes.
It turns out that we only need to know whether the allocation is for
the chunk root or not -- and we can pass that around as a bool instead.
This allows us to pull root usage out of the reservation path all the
way up to reserve_metadata_bytes itself, which uses it only to compare
against fs_info->chunk_root to set the bool. In turn, this eliminates
a bunch of races where we use a particular root too early in the mount
process.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There are two places where we don't already know what kind of alloc
profile we need before calling btrfs_get_alloc_profile, but we need
access to a root everywhere we call it.
This patch adds helpers for btrfs_{data,metadata,system}_alloc_profile()
and relegates btrfs_system_alloc_profile to a static for use in those
two cases. The next patch will eliminate one of those.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The end io work queue items have been tracked by the work queues since
"Btrfs: Add async worker threads for pre and post IO checksumming"
(8b71284292) (2008).
Signed-off-by: David Sterba <dsterba@suse.com>
The list used to track checksums in the early version (2.6.29), but I
was able not pinpoint the commit that stopped using it. Everything
apparently works without it for a long time.
Signed-off-by: David Sterba <dsterba@suse.com>
Seems to be unused since the initial commit, we ignore readahead errors
anyway, the full read will handle that if necessary.
Signed-off-by: David Sterba <dsterba@suse.com>
Both btrfs_create_free_space_tree and btrfs_clear_free_space_tree
contain:
if (ret)
return ret;
return 0;
The if statement is only false when ret equals zero, and since we return
zero in such cases, we can safely remove the branching.
Signed-off-by: Sahil Kang <sahil.kang@asilaycomputing.com>
Signed-off-by: David Sterba <dsterba@suse.com>
We only pass GFP_NOFS to btrfs_bio_clone_partial, so lets hardcode it.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
A rewrite of btrfs_submit_direct_hook appears to have introduced a warning:
fs/btrfs/inode.c: In function 'btrfs_submit_direct_hook':
fs/btrfs/inode.c:8467:14: error: 'bio' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Where the 'bio' variable was previously initialized unconditionally, it
is now set in the "while (submit_len > 0)" loop that would never execute
if submit_len is zero.
Assuming this cannot happen in practice, we can avoid the warning
by simply replacing the while{} loop with a do{}while() loop so
the compiler knows that it will always be entered at least once.
Fixes changes introduced in "Btrfs: use bio_clone_bioset_partial to
simplify DIO submit".
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Sterba <dsterba@suse.com>
All dio endio functions are using io_bio for struct btrfs_io_bio, this
makes btrfs_submit_direct to follow this convention.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Some check-integrity code depends on bio->bi_vcnt, this changes it to use
bio segments because some bios passing here may not have a reliable
bi_vcnt.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
In the nocsum case of dio read endio, it returns immediately if an error
gets returned when repairing, which leaves the rest blocks unrepaired. The
behavior is different from how buffered read endio works in the same case.
This changes it to record error only and go on repairing the rest blocks.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Since dio submit has used bio_clone_fast, the submitted bio may not have a
reliable bi_vcnt, for the bio vector iterations in checksum related
functions, bio->bi_iter is not modified yet and it's safe to use
bio_for_each_segment, while for those bio vector iterations in dio read's
endio, we now save a copy of bvec_iter in struct btrfs_io_bio when cloning
bios and use the helper __bio_for_each_segment with the saved bvec_iter to
access each bvec.
Also for dio reads which don't get split, we also need to save a copy of
bio iterator in btrfs_bio_clone to let __bio_for_each_segments to access
each bvec in dio read's endio. Note that it doesn't affect other calls of
btrfs_bio_clone() because they don't need to use this iterator.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Currently when mapping bio to limit bio to a single stripe length, we
split bio by adding page to bio one by one, but later we don't modify
the vector of bio at all, thus we can use bio_clone_fast to use the
original bio vector directly.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This adds a new helper btrfs_bio_clone_partial, it'll allocate a cloned
bio that only owns a part of the original bio's data.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
For raid1 and raid10, we clone the original bio to the bios which are then
sent to different disks.
Right now we use bio_clone_bioset to create a clone bio with iterating
bi_io_vec to initialize it. This changes it to use bio_clone_fast()
which creates a clone bio but only copies the bi_io_vec pointer
instead of iterating bi_io_vec.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Instead pass around the failure tree and the io tree.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Once we remove the btree_inode we won't have an inode to pass anymore,
just pass the fs_info directly and the inum since we use that to print
out the repair message.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
For extent_io tree's we have carried the address_mapping of the inode
around in the io tree in order to pull the inode back out for calling
into various tree ops hooks. This works fine when everything that has
an extent_io_tree has an inode. But we are going to remove the
btree_inode, so we need to change this. Instead just have a generic
void * for private data that we can initialize with, and have all the
tree ops use that instead. This had a lot of cascading changes but
should be relatively straightforward.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ minor reordering of the callback prototypes ]
Signed-off-by: David Sterba <dsterba@suse.com>
This patch adds the read-write attribute quota_override into sysfs.
Any process which has CAP_SYS_RESOURCE can set this flag to on, and
once it is set to true, processes with CAP_SYS_RESOURCE can exceed
the quota.
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Reviewed-by: David Sterba <dsterba@suse.com>
[ minor changelog edits ]
Signed-off-by: David Sterba <dsterba@suse.com>
This patch introduces the quota override flag to btrfs_fs_info, and a
change to quota limit checking code to temporarily allow for quota to be
overridden for processes with CAP_SYS_RESOURCE.
It's useful for administrative programs, such as log rotation, that may
need to temporarily use more disk space in order to free up a greater
amount of overall disk space without yielding more disk space to the
rest of userland.
Eventually, we may want to add the idea of an operator-specific quota,
operator reserved space, or something else to allow for administrative
override, but this is perhaps the simplest solution.
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Reviewed-by: David Sterba <dsterba@suse.com>
[ minor changelog edits ]
Signed-off-by: David Sterba <dsterba@suse.com>
The ->free_chunk_space variable is used to track the unallocated space
and access to it is protected by a spinlock, which is not used for
anything else. Make the code a bit self-explanatory by switching the
variable to an atomic64_t type and kill the spinlock.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
[ not a performance critical code, use of atomic type is ok ]
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This adds comments to the flush error handling part of the code, and
hopes to maintain the same logic with a framework which can be used to
handle the errors at the volume level.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
These FIXMEs were already addressed in 2013. All functions check for
qgroup existence:
* btrfs_add_qgroup_relation
* btrfs_ioctl_qgroup_create
* btrfs_limit_qgroup
* btrfs_del_qgroup_relation
Signed-off-by: Daichou <tommy0705c@gmail.com>
[ enhance and reformat changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
Remove NULL test on kmap() as it will always return a valid pointer.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When a buffer is modified, logged and committed, it ultimately ends
up sitting on the AIL with a dirty bli waiting for metadata
writeback. If another transaction locks and invalidates the buffer
(freeing an inode chunk, for example) in the meantime, the bli is
flagged as stale, the dirty state is cleared and the bli remains in
the AIL.
If a shutdown occurs before the transaction that has invalidated the
buffer is committed, the transaction is ultimately aborted. The log
items are flagged as such and ->iop_unlock() handles the aborted
items. Because the bli is clean (due to the invalidation),
->iop_unlock() unconditionally releases it. The log item may still
reside in the AIL, however, which means the I/O completion handler
may still run and attempt to access it. This results in assert
failure due to the release of the bli while still present in the AIL
and a subsequent NULL dereference and panic in the buffer I/O
completion handling. This can be reproduced by running generic/388
in repetition.
To avoid this problem, update xfs_buf_item_unlock() to first check
whether the bli is aborted and if so, remove it from the AIL before
it is released. This ensures that the bli is no longer accessed
during the shutdown sequence after it has been freed.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
If a filesystem shutdown occurs with a buffer log item in the CIL
and a log force occurs, the ->iop_unpin() handler is generally
expected to tear down the bli properly. This entails freeing the bli
memory and releasing the associated hold on the buffer so it can be
released and the filesystem unmounted.
If this sequence occurs while ->bli_refcount is elevated (i.e.,
another transaction is open and attempting to modify the buffer),
however, ->iop_unpin() may not be responsible for releasing the bli.
Instead, the transaction may release the final ->bli_refcount
reference and thus xfs_trans_brelse() is responsible for tearing
down the bli.
While xfs_trans_brelse() does drop the reference count, it only
attempts to release the bli if it is clean (i.e., not in the
CIL/AIL). If the filesystem is shutdown and the bli is sitting dirty
in the CIL as noted above, this ends up skipping the last
opportunity to release the bli. In turn, this leaves the hold on the
buffer and causes an unmount hang. This can be reproduced by running
generic/388 in repetition.
Update xfs_trans_brelse() to handle this shutdown corner case
correctly. If the final bli reference is dropped and the filesystem
is shutdown, remove the bli from the AIL (if necessary) and release
the bli to drop the buffer hold and ensure an unmount does not hang.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
gcc-7 flags the use of integer math inside of a condition
as a potential bug:
fs/xfs/xfs_bmap_util.c: In function 'xfs_swap_extents_check_format':
fs/xfs/xfs_bmap_util.c:1619:8: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context]
fs/xfs/xfs_bmap_util.c:1629:8: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context]
There is already a helper function for testing the di_forkoff
field for zero, so let's use that instead to shut up the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The t_lsn is not used anymore and the t_commit_lsn is used as a tmp
storage for the checkpoint sequence number only in the current code.
And the start/commit lsn are tracked as a transaction group tag in
the xfs_cil_ctx instead of a single transaction, so remove them from
the xfs_trans structure and their users to match with the design.
Signed-off-by: Shan Hai <shan.hai@oracle.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
XFS_HSIZE is an extremly confusing way to calculate the size of handle_t.
Given that handle_t always only had two sizes, and one of them isn't
even covered by XFS_HSIZE to start with just remove the macro and use
a constant sizeof expression.
Note that XFS_HSIZE isn't used in xfsprogs, xfsdump or xfstests either.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
If a transaction log reservation overrun occurs, the ticket data
associated with the reservation is dumped in xfs_log_commit_cil().
This occurs long after the transaction items and details have been
removed from the transaction and effectively lost. This limited set
of ticket data provides very little information to support debugging
transaction overruns based on the typical report.
To improve transaction log reservation overrun reporting, create a
helper to dump transaction details such as log items, log vector
data, etc., as well as the underlying ticket data for the
transaction. Move the overrun detection from xfs_log_commit_cil() to
xlog_cil_insert_items() so it occurs prior to migration of the
logged items to the CIL. Call the new helper such that it is able to
dump this transaction data before it is lost.
Also, warn on overrun to provide callstack context for the offending
transaction and include a few additional messages from
xlog_cil_insert_items() to display the reservation consumed locally
for overhead such as log vector headers, split region headers and
the context ticket. This provides a complete general breakdown of
the reservation consumption of a transaction when/if it happens to
overrun the reservation.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Transaction reservation overrun detection currently occurs too late
to print useful information about the offending transaction.
Ideally, the transaction data is printed before the associated log
items are moved from the transaction to the CIL, which occurs in
xlog_cil_insert_items(), such that details of the items logged by
the transaction are available for analysis.
Refactor xlog_cil_insert_items() to facilitate moving tx overrun
detection to this function. Update the function to track each bit of
extra log reservation stolen from the transaction (i.e., such as for
the CIL context ticket) and perform the log item migration as the
last operation before the CIL lock is released. This creates a
context where the transaction reservation consumption has been fully
calculated when the log items are moved to the CIL. This patch makes
no functional changes.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
xlog_print_tic_res() pre-dates delayed logging and the committed
items list (CIL) and thus retains some factoring warts, such as hard
coded function names in the output and the fact that it induces a
shutdown.
In preparation for more detailed logging of regular transaction
overrun situations, refactor xlog_print_tic_res() to be slightly
more generic. Reword some of the warning messages and pull the
shutdown into the callers.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
While configurable at runtime, the DEBUG mode assert failure
behavior is usually either desired or not for a particular
situation. For example, developers using kernel modules may prefer
for fatal asserts to remain disabled across module reloads while QE
engineers doing broad regression testing may prefer to have fatal
asserts enabled on boot to facilitate data collection for bug
reports.
To provide a compromise/convenience for developers, create a Kconfig
option that sets the default value of the DEBUG mode 'bug_on_assert'
sysfs tunable. The default behavior remains to trigger kernel BUGs
on assert failures to preserve existing behavior across kernel
configuration updates with DEBUG mode enabled.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
In DEBUG mode, assert failures unconditionally trigger a kernel BUG.
This is useful in diagnostic situations to panic a system and
collect detailed state information at the time of a failure.
This can also cause problems in cases where DEBUG mode code is
desired but it is preferable not trigger kernel BUGs on assert
failure. For example, during development of new code or during
certain xfstests tests that intentionally cause corruption and test
the kernel for survival (but otherwise may expect to trigger assert
failures).
To provide additional flexibility, create the
<sysfs>/fs/xfs/debug/bug_on_assert tunable to configure assert
failure behavior at runtime. This tunable is only available in DEBUG
mode and is enabled by default to preserve existing default
behavior. When disabled, assert failures in DEBUG mode result in
kernel warnings.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Linus Torvalds