Add HV mode KVM to Book3 server 64bit defconfigs as a module.
Doesn't add much to the size:
text data bss dec hex filename
8244109 4686767 994000 13924876 d47a0c vmlinux.vanilla
8256092 4691607 994128 13941827 d4bc43 vmlinux.kvm
This should enable more testing of this configuration.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits)
powerpc/p3060qds: Add support for P3060QDS board
powerpc/83xx: Add shutdown request support to MCU handling on MPC8349 MITX
powerpc/85xx: Make kexec to interate over online cpus
powerpc/fsl_booke: Fix comment in head_fsl_booke.S
powerpc/85xx: issue 15 EOI after core reset for FSL CoreNet devices
powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO driver
powerpc/85xx: Add 'fsl,pq3-gpio' compatiable for GPIO driver
powerpc/86xx: Correct Gianfar support for GE boards
powerpc/cpm: Clear muram before it is in use.
drivers/virt: add ioctl for 32-bit compat on 64-bit to fsl-hv-manager
powerpc/fsl_msi: add support for "msi-address-64" property
powerpc/85xx: Setup secondary cores PIR with hard SMP id
powerpc/fsl-booke: Fix settlbcam for 64-bit
powerpc/85xx: Adding DCSR node to dtsi device trees
powerpc/85xx: clean up FPGA device tree nodes for Freecsale QorIQ boards
powerpc/85xx: fix PHYS_64BIT selection for P1022DS
powerpc/fsl-booke: Fix setup_initial_memory_limit to not blindly map
powerpc: respect mem= setting for early memory limit setup
powerpc: Update corenet64_smp_defconfig
powerpc: Update mpc85xx/corenet 32-bit defconfigs
...
Fix up trivial conflicts in:
- arch/powerpc/configs/40x/hcu4_defconfig
removed stale file, edited elsewhere
- arch/powerpc/include/asm/udbg.h, arch/powerpc/kernel/udbg.c:
added opal and gelic drivers vs added ePAPR driver
- drivers/tty/serial/8250.c
moved UPIO_TSI to powerpc vs removed UPIO_DWAPB support
The P3060QDS is a Freescale reference board that hosts the six-core P3060 SOC.
The P3060 Processor combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.
P3060QDS Board Overview:
Memory subsystem:
- 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
- 128M Bytes NOR flash single-chip memory
- 16M Bytes SPI flash
- 8K Bytes AT24C64 I2C EEPROM
Ethernet:
- 4x1G + 4x1G/2.5G Ethernet controllers
- 2xRGMII + 1xMII, three VSC8641 PHYs on board
- Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3
PCIe: Two PCI Express 2.0 controllers/ports
USB: Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board
I2C: Four I2C controllers
UART: Supports up to four UARTs
RapidIO: Supports two serial RapidIO ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Results from updates via make savedefconfig.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There's only p2041rdb board for official release, but the p2041 silicon
on the board can be converted to p2040 silicon without XAUI and L2 cache
function, then the board becomes p2040rdb board. so we use the file name
p2041_rdb.c to handle P2040RDB board and P2041RDB board which is also
consistent with the board name under U-Boot.
During the rename we make few other minor changes to the device tree:
* Move USB phy setting into p2041si.dtsi as its SoC not board defined
* Convert PCI clock-frequency to decimal to be more readable
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Activate all MPC512x related boards. Also enable GPIO-driver, SPI driver
and at25 to test SPI. Enable DEVTMPFS. Bump to 3.1-rc6.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Move the driver to the place where it is expected to be nowadays. Also
rename its CONFIG-name to match the rest and adapt the defconfigs.
Finally, move selection of REQUIRE_GPIOLIB or WANTS_OPTIONAL_GPIOLIB to
the platforms, because this option is per-platform and not per-driver.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Audio support for the MPC5200 exists, so enable it by default.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
corenet based SoCs have SEC4 h/w, so enable the SEC4 driver,
caam, and the algorithms it supports, and disable the
SEC2/3 driver, talitos.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable the audio drivers in the non-corenet 85xx defconfigs so that audio
is enabled on the Freescale P1022DS reference board.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In commit 9aa3283595 (ehea/ibm*: Move the
IBM drivers) the IBM_NEW_EMAC* were renames to IBM_EMAC*
The conversion was incomplete so that even if the driver was added to
the .config it wasn't built, but there were no errors). In this commit
we also update the various defconfigs that use EMAC to use the new
Kconfig symbol, and explicitly add the NET_VENDOR_IBM guard.
We do not explicitly select the Kconfig dependencies, as this would force
EMAC on. Doing it in the defconfig allows more flexibility.
Tested on a canyondlands board.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a result of changes to Kconfig files, we no longer enable
the lockup and hung task detectors. Both are very light weight
and provide useful information in the event of a hang, so
reenable them.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add mpt2sas driver to pseries and ppc64 defconfig.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The IRQs off tracer enables mcount which has a big impact on
performance. Disable it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The pseries defconfig had a number of drivers enabled and we may
as well add them to the ppc64 defconfig.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The 44x code (which is shared by 47x) assumes the available physical memory
begins at 0x00000000. This is not necessarily the case in an AMP
environment.
Support CONFIG_RELOCATABLE for 476 in order to allow the kernel to be
loaded into a higher memory range.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
P2040RDB Specification:
-----------------------
2Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
128 Mbyte NOR flash single-chip memory
256 Kbit M24256 I2C EEPROM
16 Mbyte SPI memory
SD connector to interface with the SD memory card
dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
I2C1: Real time clock, Temperature sensor
I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
UART: supports two UARTs up to 115200 bps for console
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
PCIe:
- Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
- Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_PPC_EPAPR_HV_BYTECHAN adds support for the Freescale hypervisor
byte channel tty driver.
CONFIG_VIRT_DRIVERS and CONFIG_FSL_HV_MANAGER add support for the Freescale
hypervisor management driver.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove duplicate assignment of SCSI_BNX2_ISCSI in pseries_defconfig
introduced by:
37e0c21e powerpc/pseries: Enable iSCSI support for a number of cards
causes warning:
arch/powerpc/configs/pseries_defconfig:151:warning: override: reassigning to symbol SCSI_BNX2_ISCSI
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
P1010RDB Overview
-----------------
1Gbyte DDR3 (on board DDR)
32Mbyte 16bit NOR flash
32Mbyte SLC NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
I2C Board 128x8 bit memory
SD/MMC connector to interface with the SD memory card
2 SATA interface
1 internal SATA connect to 2.5. 160G SATA2 HDD
1 eSATA connector to rear panel
USB 2.0
x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
eTSEC1: Connected to RGMII PHY VSC8641XKO
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY VSC8221 eCAN
Two DB-9 female connectors for Field bus interface UART
DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable framebuffer console support by default in the defconfig on the
Freescale MPC8610 HPCD reference board. This allows the boot messages to
be shown on the video display.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable framebuffer console support by default in the defconfigs for the
Freescale 85xx-based reference board. This allows the boot messages to
be shown on the video display on the P1022DS.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1023 processor is an e500v2 based SoC that utilizes the DPAA
networking architecture. This adds basic board support for non-DPAA
functionality (device tree, board file, etc).
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The e500mc and e5500 based cores are only available on corenet based
SoCs. We use this name for the P204x, P3040, P4040, P4080, P50x0 SoCs
and any future processors in these families.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rather than trying to use the core name we use corenet to distinquish
the platform/core combo. corenet64 will be a 64-bit kernel build and
we'll add a new defconfig for corenet32 for a 32-bit platforms.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The ns_cgroup is an annoying cgroup at the namespace / cgroup frontier and
leads to some problems:
* cgroup creation is out-of-control
* cgroup name can conflict when pids are looping
* it is not possible to have a single process handling a lot of
namespaces without falling in a exponential creation time
* we may want to create a namespace without creating a cgroup
The ns_cgroup was replaced by a compatibility flag 'clone_children',
where a newly created cgroup will copy the parent cgroup values.
The userspace has to manually create a cgroup and add a task to
the 'tasks' file.
This patch removes the ns_cgroup as suggested in the following thread:
https://lists.linux-foundation.org/pipermail/containers/2009-June/018616.html
The 'cgroup_clone' function is removed because it is no longer used.
This is a userspace-visible change. Commit 45531757b4 ("cgroup: notify
ns_cgroup deprecated") (merged into 2.6.27) caused the kernel to emit a
printk warning users that the feature is planned for removal. Since that
time we have heard from XXX users who were affected by this.
Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Signed-off-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Jamal Hadi Salim <hadi@cyberus.ca>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Acked-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This debug option has no overhead other than a slight increase in
kernel size, and makes bug reports more useful. While some end users
may prefer to save the space, as a default on a kernel config aimed
primarily at development on reference boards, it should be enabled.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Even though support for the p5020's on-chip ethernet is not yet upstream,
it is not appropriate to disable all networking support (including
loopback, unix domain sockets, external ethernet devices, etc) in the
defconfig. The networking settings are taken from mpc85xx_smp_defconfig,
minus the drivers for ethernet devices not found on any current e5500
chip.
The other changes are the result of running "make savedefconfig".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable iSCSI support for a number of cards. We had the base
networking devices enabled but forgot to enable iSCSI.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enable the Qlogic and Emulex 10Gbit adapters.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
BT_L2CAP and BT_SCO have changed to bool .
Value 'm' has invalid .
Signed-off-by: Wanlong Gao <wanlong.gao@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Ensure the Chelsio T3/T4 network drivers and iWARP drivers are
enabled in the pseries config.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Uwe Kleine-König reported:
while working on an defconfig (arm/mx27) I noticed that just updating
it[1] results in removing CONFIG_EEPROM_AT24=y. The reason is that
since commit
v2.6.36-5965-g5f2365d (misc devices: do not enable by default)
MISC_DEVICES isn't enabled anymore by default. So all defconfigs that
have CONFIG_SOME_SYMBOL=y (or =m) (with SOME_SYMBOL depending on
MISC_DEVICES) but not CONFIG_MISC_DEVICES=y suffer from the same
problem.
This restores those misc devices to the powerpc defconfigs.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Uwe Kleine-König
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The MPC852 based mgsuvd board from Keymile was initially ported,
but later on not developed further. This patch removes the respective
files to decrease merging conflicts and unneeded maintenance.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher<hs@denx.de>
Cc: Vitaly Bordug <vitb@kernel.crashing.org>
Cc: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mgcoge board from keymile is now base for some other
similar boards. Therefore the board specific name mgcoge
was renamed to a generic name km82xx. Additionally some
enhancements were made:
- rework partition table in dts file
- add cpm2_pio_c gpio controller in dts file
- update defconfig
- add pin description for SCC1
- add pin description and configuration for USB
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Beside the MPC 8360 based board kmeter1 other km83xx boards
from keymile will follow. Therefore the board specific naming
kmeter1 for functions and files were replaced with km83xx.
Additionally some updates were made:
- update defconfig for 2.6.38
- rework flash partitioning in dts file
- add gpio controller for qe_pio_c in dts
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Upcoming servers will include a Broadcom NIC, add to the defconfig to
increase testing coverage and make sure mainline builds come up with
networking.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
- Enable 64kB pages so it gets some regular testing.
- The largest POWER7 has 1024 threads so bump NR_CPUS it to match.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
