Pull networking fixes from David Miller:
1) Don't leak ipvs->sysctl_tbl, from Tommi Rentala.
2) Fix neighbour table entry leak in rocker driver, from Ying Xue.
3) Do not emit bonding notifications for unregistered interfaces, from
Nicolas Dichtel.
4) Set ipv6 flow label properly when in TIME_WAIT state, from Florent
Fourcot.
5) Fix regression in ipv6 multicast filter test, from Henning Rogge.
6) do_replace() in various footables netfilter modules is missing a
check for 0 counters in the datastructure provided by the user. Fix
from Dave Jones, and found with trinity.
7) Fix RCU bug in packet scheduler classifier module unloads, from
Daniel Borkmann.
8) Avoid deadlock in tcp_get_info() by using u64_sync. From Eric
Dumzaet.
9) Input packet processing can race with inetdev_destroy() teardown,
fix potential OOPS in ip_error() by explicitly testing whether the
inetdev is still attached. From Eric W Biederman.
10) MLDv2 parser in bridge multicast code breaks too early while
parsing. Fix from Thadeu Lima de Souza Cascardo.
11) Asking for settings on non-zero PHYID doesn't work because we do not
import the command structure from the user and use the PHYID
provided there. Fix from Arun Parameswaran.
12) Fix UDP checksums with IPV6 RAW sockets, from Vlad Yasevich.
13) Missing NF_TABLES depends for TPROXY etc can cause build failures,
fix from Florian Westphal.
14) Fix netfilter conntrack to handle RFC5961 challenge ACKs properly,
from Jesper Dangaard Brouer.
15) If netlink autobind retry fails, we have to reset the sockets portid
back to zero. From Herbert Xu.
16) VXLAN netns exit code unregisters using wrong device, from John W
Linville.
17) Add some USB device IDs to ath3k and btusb bluetooth drivers, from
Dmitry Tunin and Wen-chien Jesse Sung.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
bridge: fix lockdep splat
net: core: 'ethtool' issue with querying phy settings
bridge: fix parsing of MLDv2 reports
ARM: zynq: DT: Use the zynq binding with macb
net: macb: Disable half duplex gigabit on Zynq
net: macb: Document zynq gem dt binding
ipv4: fill in table id when replacing a route
cdc_ncm: Fix tx_bytes statistics
ipv4: Avoid crashing in ip_error
tcp: fix a potential deadlock in tcp_get_info()
net: sched: fix call_rcu() race on classifier module unloads
net: phy: Make sure phy_start() always re-enables the phy interrupts
ipv6: fix ECMP route replacement
ipv6: do not delete previously existing ECMP routes if add fails
Revert "netfilter: bridge: query conntrack about skb dnat"
netfilter: ensure number of counters is >0 in do_replace()
netfilter: nfnetlink_{log,queue}: Register pernet in first place
tcp: don't over-send F-RTO probes
tcp: only undo on partial ACKs in CA_Loss
net/ipv6/udp: Fix ipv6 multicast socket filter regression
...
Use the new zynq binding for macb ethernet, since it will disable half
duplex gigabit like the Zynq TRM says to do.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix second S2R on exynos4412 based Trats2, Odroid U3 boards which
happened after enabling L2$ and caused by commit 13cfa6c4f7 ("ARM:
EXYNOS: Fix CPU idle clock down after CPU off")
And replace the soc_is_exynosxxx() macro with of_compatible_xxx
- fix dereference of ERR_PTR of of_genpd_get_from_provider()
- fix suspend problem on old DT machines to skip the initialization
suspend and caused by commit 8b283c0254 ("ARM: exynos4/5: convert
pmu wakeup to stacked domains")
- add keep-power-in-suspend for Peach Boards to support S2R and has
been missed in previous pull-request for fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=r1wn
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung 2nd fixes for v4.1" from Kukjin Kim:
- fix second S2R on exynos4412 based Trats2, Odroid U3 boards which
happened after enabling L2$ and caused by commit 13cfa6c4f7 ("ARM:
EXYNOS: Fix CPU idle clock down after CPU off")
And replace the soc_is_exynosxxx() macro with of_compatible_xxx
- fix dereference of ERR_PTR of of_genpd_get_from_provider()
- fix suspend problem on old DT machines to skip the initialization
suspend and caused by commit 8b283c0254 ("ARM: exynos4/5: convert
pmu wakeup to stacked domains")
- add keep-power-in-suspend for Peach Boards to support S2R and has
been missed in previous pull-request for fixes
* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Use of_machine_is_compatible instead of soc_is_exynos4
ARM: EXYNOS: Fix failed second suspend on Exynos4
ARM: EXYNOS: Fix dereference of ERR_PTR returned by of_genpd_get_from_provider
ARM: EXYNOS: Don't try to initialize suspend on old DT
ARM: dts: Add keep-power-in-suspend to WiFi SDIO node for Peach Boards
Fix the main PLL frequency on Armada 375, 38x and 39x SoCs
Add clock-names to CuBox Si5351 clk generator
Add dts entries in the MAINTAINERS file
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlVV6IwACgkQCwYYjhRyO9V2iACgi038BpoDW4Nf4Ivt+6eGzGeB
2GAAoKnvitRZBNyFsWiWtvo/Yl7Rgiol
=MCEb
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.1-2' of git://git.infradead.org/linux-mvebu into fixes
Merge "mvebu fixes for 4.1 (part 2)" from Gregory CLEMENT:
Fix the main PLL frequency on Armada 375, 38x and 39x SoCs
Add clock-names to CuBox Si5351 clk generator
Add dts entries in the MAINTAINERS file
* tag 'mvebu-fixes-4.1-2' of git://git.infradead.org/linux-mvebu:
MAINTAINERS: Add dts entries for some of the Marvell SoCs
ARM: dove: Add clock-names to CuBox Si5351 clk generator
ARM: mvebu: Fix the main PLL frequency on Armada 375, 38x and 39x SoCs
The Marvell mwifiex driver prevents the system to enter into a suspend
state if the card power is not preserved during a suspend/resume cycle.
So Suspend-to-RAM and Suspend-to-idle is failing on Exynos5800 Peach Pi
and Exynos5420 Peach Pit Chromebooks.
Add the keep-power-in-suspend Power Management property to the SDIO/MMC
node so the mwifiex suspend handler doesn't fail and the system is able
to enter into a suspend state.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Commit 9fd85eb502 ("ARM: pmu: add support for interrupt-affinity
property") added an optional "interrupt-affinity" property, to specify
the CPU affinity for each SPI listed in the interrupts property.
Without this property, we get this boot warning:
CPU PMU: Failed to parse <no-node>/interrupt-affinity[0]
This patch adds interrupt-affinity to the PMU node in the
vexpress-ca15_a7(a.k.a TC2) device tree.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 9fd85eb502 ("ARM: pmu: add support for interrupt-affinity
property") added an optional "interrupt-affinity" property, to specify
the CPU affinity for each SPI listed in the interrupts property.
Without this property, we get this boot warning:
CPU PMU: Failed to parse <no-node>/interrupt-affinity[0]
This patch adds interrupt-affinity to the PMU node in the
vexpress-v2p-ca9 device tree.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit d9d1f3e2d7 ("ARM: l2c: check that DT files specify the required
"cache-unified" property") mandates to specify this required property.
Without this property, we get this boot warning:
"L2C: device tree omits to specify unified cache"
This patch adds "cache-unified" property to L2 cache node in vexpress
CA9 device tree.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This contains a fix for a bug that was introduced a couple of months ago
by a patch that git misapplied because of a lack of context.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=8e1C
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.1-fixes-for-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into fixes
Merge "ARM: tegra: Device tree fixes for v4.1-rc3" from Thierry Reding:
This contains a fix for a bug that was introduced a couple of months ago
by a patch that git misapplied because of a lack of context.
* tag 'tegra-for-4.1-fixes-for-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Correct which USB controller has the UTMI pad registers
Si5351 clock generator on CuBox uses XTAL as clock reference, name the
clock phandle accordingly.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
- fixes commit ea08de16eb ("ARM: dts: Add DISP1 power
domain for exynos5420") which causes 'unhandled fault:
imprecise external abort' error when PD turned off.
: make DP a consumer of DISP1 power domain
- fixes 's3c-rtc' probe failure on Odriod-X2/U2/U3 boards.
: add 'rtc_src' clock to rtc node for source clock of rtc
- fixes typo for 'cpu-crit-0' trip point on exynos5420/5440
- fixes S2R failure on exynos5250-snow due to card power of
Marvell WiFi driver (suspend/resume)
: add keep-power-in-susped to WiFi SDIO node
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJVT23xAAoJEA0Cl+kVi2xqZIcP/0CAA25uvidVXdNVYlJbSvr3
4kesNDG/LGrVnv6xt132iJsXtIfWQxG6nJkhE1x5G9zSgsAjtQWcsCr068Itktsg
CG1yl/8z6TB+wS0PhTXaa985V62euTws89YGJau6YCZVSXKKcGDjM5e2RJn80yOL
IMipw8x5xTt0GsIKtC2AyewcNq05SSNtwvYe8CPJ9wGFQPy3gZ1t5WqSwW2mMG+K
C6mibaN7gs9+sS2ncHglZtHKAR2VxJTNCkq/LOCYlDSftT01GhmhG1fl/tUxEqUD
1bFTTajA21CNnEvWCdkFkMHkEy7lzW8WCX3tAwDHGON/NdWERV4FSaLTqR0o1ekO
vLeUSvgtRntBtUY3ojvyfoYq4vrdQF1uoL2r932iO9FILUBpwRYAyG152VFJyZRx
Hx50yCgyljG3X8xUp5VgiuNwDCgatiFBCeb3YT0qrB9YbnLXqqAUAfMSng8a15dc
rbD02YsYvYcJPf7RDnS9QQV+ZSSmZIkY7JmxkJ/UJ0SA7dAJBtKrXQyliLVlExHu
Cz0ye5NHjC+jxwPU/OEFRSZi8bKJXe/q6bAXDRA0vkZWd0G6C+wOq8bnzSWkRM+D
+/uzxajdDbfs7mr2mPFyc3H22MiwWSOFIRVsCXVKqTN0yVvlaLvHtolUayAD3RrR
oo25jYh9CYGZhxd+7TVb
=YBxq
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung
Pull samsung fixes from Kukjin Kim:
"Here is Samsung fixes for v4.1. Since I've missed to send this via
arm-soc tree before v4.1-rc3, so I'm sending this to you directly
- fix commit ea08de16eb ("ARM: dts: Add DISP1 power domain for
exynos5420") which causes 'unhandled fault: imprecise external
abort' error when PD turned off. ("make DP a consumer of DISP1
power domain")
- fix 's3c-rtc' probe failure on Odriod-X2/U2/U3 boards ("add
'rtc_src' clock to rtc node for source clock of rtc")
- fix typo for 'cpu-crit-0' trip point on exynos5420/5440
- fix S2R failure on exynos5250-snow due to card power of Marvell
WiFi driver (suspend/resume) ("add keep-power-in-susped to WiFi
SDIO node")"
* tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add keep-power-in-suspend to WiFi SDIO node for exynos5250-snow
ARM: dts: Fix typo in trip point temperature for exynos5420/5440
ARM: dts: add 'rtc_src' clock to rtc node for exynos4412-odroid boards
ARM: dts: Make DP a consumer of DISP1 power domain on Exynos5420
The Marvell mwifiex driver prevents the system to enter into a suspend
state if the card power is not preserved during a suspend/resume cycle.
So Suspend-to-RAM and Suspend-to-idle are failing on Exynos5250 Snow.
Add the keep-power-in-suspend Power Management property to the SDIO/MMC
node so the mwifiex suspend handler doesn't fail and the system is able
to enter into a suspend state.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Remove the extra zero in the "cpu-crit-0" trip point for exynos5420
and exynos5440.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Exynos4412 SoC has a s3c6410 RTC where the source clock
is now a mandatory property.
This patch fixes probe failure of s3c-rtc on Odroid-X2/U2/U3 boards.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Commit ea08de16eb ("ARM: dts: Add DISP1 power domain for exynos5420")
added a device node for the Exynos5420 DISP1 power domain but dit not
make the DP controller a consumer of that power domain.
This causes an "Unhandled fault: imprecise external abort" error if the
exynos-dp driver tries to access the DP controller registers and the PD
was turned off. This lead to a kernel panic and a complete system hang.
Make the DP controller device node a consumer of the DISP1 power domain
to ensure that the PD is turned on when the exynos-dp driver is probed.
Fixes: ea08de16eb ("ARM: dts: Add DISP1 power domain for exynos5420")
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
in the Ux500 DT but triggered by proper error handling in v4.1-rc1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2YtL
-----END PGP SIGNATURE-----
Merge tag 'stericsson-fixes-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
Merge "Ux500 fixes" from Linus Walleij:
This fixes an MMC/SD configuration issue present for some time
in the Ux500 DT but triggered by proper error handling in v4.1-rc1.
* tag 'stericsson-fixes-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Enable GPIO regulator for SD-card for snowball
ARM: ux500: Enable GPIO regulator for SD-card for HREF boards
ARM: ux500: Move GPIO regulator for SD-card into board DTSs
creeping up during idle, and two l3-noc device fixes:
- Fix power consumption creeping up with I2C4 staying on
- Fix n900 microphone bias voltages
- Fix dra7 l3-noc for host clock
- Fix omap5 l3-noc id address decoding
The rest are all just minor dts fixes:
- Fix changed EXTCON_USB_GPIO_USB in defconfig
- Fix missing isp and iva #iommu-cells property
- Various beagle x15 dts fixes for pre-production changes
- Fix am437x-sk display dts entries
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tOGf
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.1/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v4.1-rc1" from Tony Lindgren:
Fixes for omaps, mostly a fix for power power consumption
creeping up during idle, and two l3-noc device fixes:
- Fix power consumption creeping up with I2C4 staying on
- Fix n900 microphone bias voltages
- Fix dra7 l3-noc for host clock
- Fix omap5 l3-noc id address decoding
The rest are all just minor dts fixes:
- Fix changed EXTCON_USB_GPIO_USB in defconfig
- Fix missing isp and iva #iommu-cells property
- Various beagle x15 dts fixes for pre-production changes
- Fix am437x-sk display dts entries
* tag 'omap-for-v4.1/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: omap_l3_noc: Fix master id address decoding for OMAP5
bus: omap_l3_noc: Fix offset for DRA7 CLK1_HOST_CLK1_2 instance
ARM: dts: dra7: Fix efuse register size for ABB
ARM: dts: am57xx-beagle-x15: Switch GPIO fan number
ARM: dts: am57xx-beagle-x15: Switch UART mux pins
ARM: dts: am437x-sk: reduce col-scan-delay-us
ARM: dts: am437x-sk: fix for new newhaven display module revision
ARM: dts: am57xx-beagle-x15: Fix RTC aliases
ARM: dts: am57xx-beagle-x15: Fix IRQ type for mcp7941x
ARM: dts: omap3: Add #iommu-cells to isp and iva iommu
ARM: omap2plus_defconfig: Enable EXTCON_USB_GPIO
ARM: dts: OMAP3-N900: Add microphone bias voltages
ARM: OMAP2+: Fix omap off idle power consumption creeping up
Disable the unused internal RTC in the dts of the OpenBlock AX3
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlVDtLIACgkQCwYYjhRyO9WCiwCfTBYFFDMZxK/W9qLdhU8mj/iD
tDQAn3TDsfWEIHm+c6DeZqj35Q74yPGA
=Gggv
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.1' of git://git.infradead.org/linux-mvebu into fixes
Pull "mvebu fix for 4.1" from Gregory CLEMENT:
Disable the unused internal RTC in the dts of the OpenBlock AX3
* tag 'mvebu-fixes-4.1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: armada-xp-openblocks-ax3-4: Disable internal RTC
The L3 Error handling on OMAP5 for the most part is very similar
to that of OMAP4, and had leveraged common data structures and
register layout definitions so far. Upon closer inspection, there
are a few minor differences causing an incorrect decoding and
reporting of the master NIU upon an error:
1. The L3_TARG_STDERRLOG_MSTADDR.STDERRLOG_MSTADDR occupies
11 bits on OMAP5 as against 8 bits on OMAP4, with the master
NIU connID encoded in the 6 MSBs of the STDERRLOG_MSTADDR
field.
2. The CLK3 FlagMux component has 1 input source on OMAP4 and 3
input sources on OMAP5. The common DEBUGSS source is at a
different input on each SoC.
Fix the above issues by using a OMAP5-specific compatible property
and using SoC-specific data where there are differences.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix a typo in DRA7 dtsi where 12 bytes are needed for register
description of ABB efuse registers, however only 8 bytes are provided
to map. For some weird reason, this does not generate abort at offset
0x8, probably due to default maps already provided in io.c for the bus
register ranges.
Reported-by: Matt Gessner <Matt.Gessner@windriver.com>
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBoard-X15 pre-production change includes switching the GPIO fan
gpio over from 1 to 2 to allow for a potential fix at a later point in
time for USB client VBUS detection using PMIC VBUS detect capability.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBoard-X15 pre-production change includes switching over to UART
pins that now allow for UART download capability. All original boards
should either have been returned for modifications or already modified
for the required change and maintaining compatibility for older boards
are no longer needed.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The new AM437x SK Beta boards have removed the
large capacitors on the gpio-matrix column lines
which means we can reduce col-scan-delay-us to 5us
without loosing functionality.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM437x Starter Kit uses a NewHaven Display module with
a 4.3" display and EDT FT5306 touchscreen
On that module's new revision, NewHave decided to change
the pinout on the 6 pin flat-pcb touchscreen connector so
that instead of having WAKE pin, we now have RESETn.
The new display module is available on AM437x SK Beta and
all new revisions while the older revision is only available
on AM437x SK Alpha which, unfortunately, can't be supported
anymore in mainline without a revert of this patch.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With commit bc078316d8 ("ARM: dts: DRA7: Add node for RTC"), we now
have AM57xx RTC register itself as alias 0 even before DS1307 or TPS
rtc drivers are loaded up. However, since neither TPS, nor AM57xx RTC
are capable of being backedup by battery, we would like to maintain
the "primary" rtc as mcp79410 rtc device.
This also generates the following warnings in the bootlog highlighting
the issue:
[ 5.895445] rtc-ds1307 2-006f: /aliases ID 0 not available
...
[ 6.476285] palmas-rtc 48070000.i2c:tps659038@58:tps659038_rtc: /aliases ID 1 not available
So, add proper aliases to ensure that RTC order is always consistent
to userspace immaterial of probe order.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The interrupt polarity provided in devicetree is used to configure
the interrupt controller(ARM GIC), however, it seems that we have an
inverter at the GIC boundary inside AM57xx which inverts the signal
input from sys_irq external interrupt source.
Further, as per GIC distributor TRM,
http://infocenter.arm.com/help/topic/com.arm.doc.ddi0438d/BGBHIACJ.html#BABJFCFB
ARM GIC distributor does not support IRQ trigger type
IRQ_TYPE_LEVEL_LOW, and only rising or level high signals.
However, for some reason, the current configuration(which gets ignored
by GIC driver) functions on some platforms, however, on few platforms
results in infinite interrupts hogging the system down.
Switch over to rising edge for GIC configuration which is also aligned
with trigger point from the RTC chip and the internal inversion.
Fixes: 5a0f93c657 ("ARM: dts: Add am57xx-beagle-x15")
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing #iommu-cells property to the isp and iva iommu nodes. This
fixes the binding (property is required according to the generic iommu
binding) and removes the following kernel warning triggered once the
iommu nodes are referenced:
[ 0.647521] /ocp/isp@480bc000: could not get #iommu-cells for /ocp/mmu@480bd400
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
N900 audio recording needs that codec provides bias voltage for integrated
digital microphone and headset microphone depending which one is used.
Digital microphone uses 2 V bias and it comes from the codec A part. Codec
B part drives the headset microphone bias and that is set to 2.5 V.
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[Jarkko: Headset mic bias changed to 2 (2.5 V) as it was before commit
e2e8bfdf61 ("ASoC: tlv320aic3x: Convert mic bias to a supply widget")]
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Whereas for Armada 370 and XP the main PLL frequency was 2GHz for the
Armada 375, 38x and 39x, the frequency is 1GHz. When writing support
for these last SoCs, there was no official value for the PLL. Now that
we have it, this patch fixes it in the device tree.
This value is currently only used by the NAND driver for the setting
the NAND timing. Fortunately it is not actually used: all the mainline
board with a NAND flash comes with a NAND device tree node using the
"marvell,nand-keep-config" property. With this property the timings
are not modified in the kernel driver and are kept from the
bootloader.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marcin Wojtas <mw@semihalf.com>
The adv7511 IRQ is low level triggered, not falling edge triggered. The
wrong sense configuration results in no interrupt being triggered at
all, breaking hotplug detection. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Fixes: 83a0731b39 ("ARM: shmobile: koelsch: Add DU HDMI output support")
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
It should be the first controller, not the second. The indexes of the
usb resets were also wrong and have been fixed.
The issue was caused by the changes in 308efde ("ARM: tegra: Add resets
& has-utmi-pad-registers flag to all USB PHYs") being misapplied by git
due to the patch context being insufficient.
This broke USB after 6261b06 ("regulator: Defer lookup of supply to
regulator_get"), because it changed the order in which the controllers
were probed.
The fix for this issue was suggested by Mikko Perttunen and Tuomas
Tynkkynen.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Cc: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The pinctrl-assert-gpios is an invalid pinctrl property. It was
probably sneaked from vendor tree. Remove it.
Fixes: 4e18a2243a ("ARM: imx6qdl-sabreauto.dtsi: add max7310 support")
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Fix a typo in the TX DMA interrupt name for AUART4.
This patch makes AUART4 operational again.
Signed-off-by: Marek Vasut <marex@denx.de>
Fixes: f30fb03d4d ("ARM: dts: add generic DMA device tree binding for mxs-dma")
Cc: stable@vger.kernel.org
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The property '#pwm-cells' is currently missing. It is not possible to
use pwm4 without this property.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Fixes: 5658a68fb5 ("ARM i.MX25: Add devicetree")
Cc: <stable@vger.kernel.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The fixed-regulator bindings require a separate property enable-active-high,
the standard gpio phandle property polarity setting is ignored.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Fixes: 4fe69a934b ("ARM: dts: Add Phytec pfla02 with i.MX6 DualLite/Solo")
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The dr_mode of usb0 on imx233-olinuxino is left to default "otg".
Since the green LED (GPIO2_1) on imx233-olinuxino is connected to the
same pin as USB_OTG_ID it's possible to disable USB host by LED toggling:
echo 0 > /sys/class/leds/green/brightness
[ 1068.890000] ci_hdrc ci_hdrc.0: remove, state 1
[ 1068.890000] usb usb1: USB disconnect, device number 1
[ 1068.920000] usb 1-1: USB disconnect, device number 2
[ 1068.920000] usb 1-1.1: USB disconnect, device number 3
[ 1069.070000] usb 1-1.2: USB disconnect, device number 4
[ 1069.450000] ci_hdrc ci_hdrc.0: USB bus 1 deregistered
[ 1074.460000] ci_hdrc ci_hdrc.0: timeout waiting for 00000800 in 11
This patch fixes the issue by setting dr_mode to "host" in the dts file.
Reported-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Peter Chen <peter.chen@freescale.com>
Fixes: b493129482 ("ARM: dts: imx23-olinuxino: Add USB host support")
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
On imx23-olinuxino the LED turns on when level logic high is aplied to
GPIO2_1.
Fix the gpios property accordingly.
Fixes: b34aa18502 ("ARM: dts: imx23-olinuxino: Remove unneeded "default-on"")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
There is no crystal connected to the internal RTC on the Open Block
AX3. So let's disable it in order to prevent the kernel probing the
driver uselessly. Eventually this patches removes the following
warning message from the boot log:
"rtc-mv d0010300.rtc: internal RTC not ticking"
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.8 +
The GPIO regulator for the SD-card isn't a ux500 SOC configuration, but
instead it's specific to the board. Move the definition of it, into the
board DTSs.
Fixes: c94a4ab7af ("ARM: ux500: Disable the MMCI gpio-regulator by default")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We were expecting to sit on this branch through most of the merge window since
the contents was merged into our tree late, but we ended up sitting on all of
our contents so it can go in with the rest.
The contents here is:
- A large branch of cleanups of the CM/PRM blocks on OMAP.
- A couple of patches plumbing up CM/PRM on OMAP5 and DRA7.
- A branch with DT updates for Freescale i.MX. including some shuffling from
.dts to .dtsi (include) files that causes a little churn.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ssbK
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late changes from Olof Johansson:
"We were expecting to sit on this branch through most of the merge
window since the contents was merged into our tree late, but we ended
up sitting on all of our contents so it can go in with the rest.
The contents here is:
- a large branch of cleanups of the CM/PRM blocks on OMAP.
- a couple of patches plumbing up CM/PRM on OMAP5 and DRA7.
- a branch with DT updates for Freescale i.MX. including some
shuffling from .dts to .dtsi (include) files that causes a little
churn"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (78 commits)
ARM: OMAP2+: Fix booting with configs that don't have MFD_SYSCON
ARM: OMAP4+: control: add support for initializing control module via DT
ARM: dts: dra7: add minimal l4 bus layout with control module support
ARM: dts: omap5: add minimal l4 bus layout with control module support
ARM: OMAP4+: control: remove support for legacy pad read/write
ARM: OMAP4: display: convert display to use syscon for dsi muxing
ARM: dts: omap4: add minimal l4 bus layout with control module support
ARM: dts: am4372: add minimal l4 bus layout with control module support
ARM: dts: am43xx-epos-evm: fix pinmux node layout
ARM: dts: am33xx: add minimal l4 bus layout with control module support
ARM: dts: omap3: add minimal l4 bus layout with control module support
ARM: dts: omap24xx: add minimal l4 bus layout with control module support
ARM: OMAP2+: control: add syscon support for register accesses
ARM: OMAP2+: id: cache omap_type value
ARM: OMAP2+: control: remove API for getting control module base address
ARM: OMAP2+: clock: add low-level support for regmap
ARM: OMAP4+: PRM: get rid of cpu_is_omap44xx calls from interrupt init
ARM: OMAP4+: PRM: setup prm_features from the PRM init time flags
ARM: OMAP2+: CM: move SoC specific init calls within a generic API
ARM: OMAP4+: PRM: determine prm_device_inst based on DT compatibility
...
The changes here belong to two main platforms:
- Atmel At91 is flipping the bit and going multiplatform. This includes some
cleanups and removal of code, and the final flip of config dependencies
- Shmobile has several platforms that are going multiplatform, but this
branch also contains a bunch of cleanups that they weren't able to keep
separate in a good way. THere's also a removal of one of their SoCs and the
corresponding boards (sh7372 and mackerel).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Vq4N
-----END PGP SIGNATURE-----
Merge tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform code changes from Olof Johansson:
"The changes here belong to two main platforms:
- Atmel At91 is flipping the bit and going multiplatform. This
includes some cleanups and removal of code, and the final flip of
config dependencies
- Shmobile has several platforms that are going multiplatform, but
this branch also contains a bunch of cleanups that they weren't
able to keep separate in a good way. THere's also a removal of one
of their SoCs and the corresponding boards (sh7372 and mackerel)"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
ARM: at91/pm: move AT91_MEMCTRL_* to pm.h
ARM: at91/pm: move the standby functions to pm.c
ARM: at91: fix pm_suspend.S compilation when ARMv6 is selected
ARM: at91: add a Kconfig dependency on multi-platform
ARM: at91: drop AT91_TIMER_HZ
ARM: at91: remove hardware.h
ARM: at91: remove SoC headers
ARM: at91: remove useless mach/cpu.h
ARM: at91: remove unused headers
ARM: at91: switch at91_dt_defconfig to multiplatform
ARM: at91: switch to multiplatform
ARM: shmobile: r8a7778: enable multiplatform target
ARM: shmobile: bockw: add sound to DT
ARM: shmobile: r8a7778: add sound to DT
ARM: shmobile: bockw: add devices hooked up to i2c0 to DT
DT: i2c: add trivial binding for OKI ML86V7667 video decoder
ARM: shmobile: r8a7778: common clock framework CPG driver
ARM: shmobile: bockw dts: set extal clock frequency
ARM: shmobile: bockw dts: Move Ethernet node to BSC
ARM: shmobile: r8a73a4: Remove legacy code
...
Driver updates for v4.1. Some of these are for drivers/soc, where we find more
and more SoC-specific drivers these days. Some are for other driver subsystems
where we have received acks from the appropriate maintainers.
The larger parts of this branch are:
- MediaTek support for their PMIC wrapper interface, a high-level interface
for talking to the system PMIC over a dedicated I2C interface.
- Qualcomm SCM driver has been moved to drivers/firmware. It's used for CPU
up/down and needs to be in a shared location for arm/arm64 common code.
- Cleanup of ARM-CCI PMU code.
- Anoter set of cleanusp to the OMAP GPMC code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/sWo
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for v4.1. Some of these are for drivers/soc, where we
find more and more SoC-specific drivers these days. Some are for
other driver subsystems where we have received acks from the
appropriate maintainers.
The larger parts of this branch are:
- MediaTek support for their PMIC wrapper interface, a high-level
interface for talking to the system PMIC over a dedicated I2C
interface.
- Qualcomm SCM driver has been moved to drivers/firmware. It's used
for CPU up/down and needs to be in a shared location for arm/arm64
common code.
- cleanup of ARM-CCI PMU code.
- another set of cleanusp to the OMAP GPMC code"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
soc/mediatek: Remove unused variables
clocksource: atmel-st: select MFD_SYSCON
soc: mediatek: Add PMIC wrapper for MT8135 and MT8173 SoCs
arm-cci: Fix CCI PMU event validation
arm-cci: Split the code for PMU vs driver support
arm-cci: Get rid of secure transactions for PMU driver
arm-cci: Abstract the CCI400 PMU specific definitions
arm-cci: Rearrange code for splitting PMU vs driver code
drivers: cci: reject groups spanning multiple HW PMUs
ARM: at91: remove useless include
clocksource: atmel-st: remove mach/hardware dependency
clocksource: atmel-st: use syscon/regmap
ARM: at91: time: move the system timer driver to drivers/clocksource
ARM: at91: properly initialize timer
ARM: at91: at91rm9200: remove deprecated arm_pm_restart
watchdog: at91rm9200: implement restart handler
watchdog: at91rm9200: use the system timer syscon
mfd: syscon: Add atmel system timer registers definition
ARM: at91/dt: declare atmel,at91rm9200-st as a syscon
soc: qcom: gsbi: Add support for ADM CRCI muxing
...
As always, this tends to be one of our bigger branches. There are lots of
updates this release, but not that many jumps out as something that needs
more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- More graphics DT pieces falling into place on Exynos, bridges, clocks.
- Plenty of DT updates for Qualcomm platforms for various IP blocks
- Some churn on Tegra due to switch-over to tool-generated pinctrl data
- Misc fixes and updates for Atmel at91 platforms
- Various DT updates to add IP block support on Broadcom's Cygnus platforms
- More updates for Renesas platforms as DT support is added for various IP
blocks (IPMMU, display, audio, etc).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVNzKFAAoJEIwa5zzehBx3JtEP/1g89CW7iZHAUyIiC+jtgqck
ASoplr13DLD0HWjjWITX3zm7J/iY57YjEv14tHH/xmrh5YCCZ+mRLqiD/Plnv0Zv
JdJRRJv/NMnMlu/tA1aBO326JOt2Vw+3YngmYayDpoRzVifx2YTJLbu2difa+6rM
vN6FpOE6U5jkvM16+gqxKxyx0tGIQz9cTn+9q2V1fDS++vZ2VvqfB5pTNul3BKAF
OVCNFJ/EUE9EPMPbmgDjYmNE/POj64kF32n7NBEQz2Z+nwDNxDAecfF356hV7o5g
JsFLNK+4c2QQqBL775xzCf5kK+n/V2cFEpDica+hU70AdWsjdAlUFrbOsWGUJLRi
4Blrv8GRxEKeOCs8AFKYCM+z3zf2ais7JMteD2VW26ywCwpUt+QEZTUVHRHU3NYQ
BMI7uyTGIH2GyLyS+Av3vikza8IbDIwlYuuDpXhCJSXXgKSnbzCrpjkhyGLccBJR
k3qgUwPJVw9hP1qaaNgvb7p9oNhTP2yLl3fQ68WqI7QWIupW0/s12INhzFFgt6zU
Nzcx010ku9yMeMMGtfiNgA3cMln+Ysfs1UIUOMQ36zP1PCtHJkZgwtZzTsBE4A04
KqmiLL/+7qsconEhEanmDzTpeXiNzERnOKSSqVN7Fwp89GEFJLrWpHSXI+8SBTHC
fB54LRTNYdlcoN0QshcT
=wqhB
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As always, this tends to be one of our bigger branches. There are
lots of updates this release, but not that many jumps out as something
that needs more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- more graphics DT pieces falling into place on Exynos, bridges,
clocks.
- plenty of DT updates for Qualcomm platforms for various IP blocks
- some churn on Tegra due to switch-over to tool-generated pinctrl
data
- misc fixes and updates for Atmel at91 platforms
- various DT updates to add IP block support on Broadcom's Cygnus
platforms
- more updates for Renesas platforms as DT support is added for
various IP blocks (IPMMU, display, audio, etc)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (231 commits)
ARM: dts: alpine: add internal pci
Revert "ARM: dts: mt8135: Add pinctrl/GPIO/EINT node for mt8135."
ARM: mvebu: use 0xf1000000 as internal registers on Armada 370 DB
ARM: dts: qcom: Add idle state device nodes for 8064
ARM: dts: qcom: Add idle states device nodes for 8084
ARM: dts: qcom: Add idle states device nodes for 8974/8074
ARM: dts: qcom: Update power-controller device node for 8064 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8084 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8074 Krait CPUs
devicetree: bindings: Document qcom,idle-states
devicetree: bindings: Update qcom,saw2 node bindings
dt-bindings: Add #defines for MSM8916 clocks and resets
arm: dts: qcom: Add LPASS Audio HW to IPQ8064 device tree
arm: dts: qcom: Add APQ8084 chipset SPMI PMIC's nodes
arm: dts: qcom: Add 8x74 chipset SPMI PMIC's nodes
arm: dts: qcom: Add SPMI PMIC Arbiter nodes for APQ8084 and MSM8974
arm: dts: qcom: Add LCC nodes
arm: dts: qcom: Add TCSR support for MSM8960
arm: dts: qcom: Add TCSR support for MSM8660
arm: dts: qcom: Add TCSR support for IPQ8064
...
Our SoC branch usually contains expanded support for new SoCs and other core
platform code. In this case, that includes:
- Support for the new Annapurna Labs "Alpine" platform
- A rework greatly simplifying adding new platform support to the MCPM
subsystem (Multi-cluster power management)
- Cpuidle and PM improvements for Exynos3250
- Misc updates for Renesas, OMAP, Meson, i.MX. Some of these could have
gone in other branches but ended up here for various reasons.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tcGs
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"Our SoC branch usually contains expanded support for new SoCs and
other core platform code. In this case, that includes:
- support for the new Annapurna Labs "Alpine" platform
- a rework greatly simplifying adding new platform support to the
MCPM subsystem (Multi-cluster power management)
- cpuidle and PM improvements for Exynos3250
- misc updates for Renesas, OMAP, Meson, i.MX. Some of these could
have gone in other branches but ended up here for various reasons"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
ARM: alpine: add support for generic pci
ARM: Exynos: migrate DCSCB to the new MCPM backend abstraction
ARM: vexpress: migrate DCSCB to the new MCPM backend abstraction
ARM: vexpress: DCSCB: tighten CPU validity assertion
ARM: vexpress: migrate TC2 to the new MCPM backend abstraction
ARM: MCPM: move the algorithmic complexity to the core code
ARM: EXYNOS: allow cpuidle driver usage on Exynos3250 SoC
ARM: EXYNOS: add AFTR mode support for Exynos3250
ARM: EXYNOS: add code for setting/clearing boot flag
ARM: EXYNOS: fix CPU1 hotplug on Exynos3250
ARM: S3C64XX: Use fixed IRQ bases to avoid conflicts on Cragganmore
ARM: cygnus: fix const declaration bcm_cygnus_dt_compat
ARM: DRA7: hwmod: Fix the hwmod class for GPTimer4
ARM: DRA7: hwmod: Add data for GPTimers 13 through 16
ARM: EXYNOS: Remove left over 'extra_save'
ARM: EXYNOS: Constify exynos_pm_data array
ARM: EXYNOS: use static in suspend.c
ARM: EXYNOS: Use platform device name as power domain name
ARM: EXYNOS: add support for async-bridge clocks for pm_domains
ARM: omap-device: add missed callback for suspend-to-disk
...
We've got a fairly large cleanup branch this time. The bulk of this is removal
of non-DT platforms of several flavors:
- Atmel at91 platforms go full-DT, with removal of remaining board-file based
support
- OMAP removes legacy board files for three more platforms
- Removal of non-DT mach-msm, newer Qualcomm platforms now live in mach-qcom
- Freescale i.MX25 also removes non-DT platform support
Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVNzI3AAoJEIwa5zzehBx3ePwQAJKb4Mf72/4iiKb4dbVcooQN
EiZ84fwWiWD6Mww/3A76xVnz/b7JWmB3vwW0b4fcbvzubmOjnROBmZgCWeNy4ZTv
dOZc3/9jK7OrlwvpFBeZykQwHcbz+550+m3WxmLft1oqH/7BA1k5aunwYtFB96ii
5Owi4Cy9OmxEyALQAvzktFaJdI7J66LNb+i30r5zIZHlkVooeF3UyadndiswUP2o
EBzCE8UPqRi5kV6FuwVyf4MZaV28FWoglTqdx9OxogcTnKNFT6RlHQ39q/iPu348
Wkh4kOryVy7Rlab1K4wQRpBoOwkonKDV73u2H2ifRFj7V9ZAdjibK8pgKn3kjkba
bJkwHIqlqtqqqjj2Hh93wl+8hKSypoLXO9tagPWYBiLtFXCH/+EVsihWYpAc/A5E
pUS6hJrJyXKJouwwsXu6459zP0ieqhvpbQG72xs9PRimAfAdSTulSTzdI/dMh42Q
pwYkmvh+ReY3Ll4MeCzu7+eCIY0qAKsor48W1ImuziwQhg2lZj16qWtA4YdPk3+O
N8ckyaaFg663PAfsZgBx1qTgxw5v0ec2k68/iEVGS5mUJCgcWxFvR95chTDIxQXq
ZmJ+SuMFyLB/2zVSiGU96L1PQTcUkxJJ8LVB3qNp6KlYT7qUSsgAU+qYveFlUh+p
X8MVsSVh8n1MTNepsLij
=BV8A
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"We've got a fairly large cleanup branch this time. The bulk of this
is removal of non-DT platforms of several flavors:
- Atmel at91 platforms go full-DT, with removal of remaining
board-file based support
- OMAP removes legacy board files for three more platforms
- removal of non-DT mach-msm, newer Qualcomm platforms now live in
mach-qcom
- Freescale i.MX25 also removes non-DT platform support"
Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
mmc: Remove msm_sdcc driver
gpio: Remove gpio-msm-v1 driver
ARM: Remove mach-msm and associated ARM architecture code
ARM: shmobile: cpuidle: Remove the pointless default driver
ARM: davinci: dm646x: Add interrupt resource for McASPs
ARM: davinci: irqs: Correct McASP1 TX interrupt definition for DM646x
ARM: davinci: dm646x: Clean up the McASP DMA resources
ARM: davinci: devices-da8xx: Add support for McASP2 on da830
ARM: davinci: devices-da8xx: Clean up and correct the McASP device creation
ARM: davinci: devices-da8xx: Add interrupt resource to McASP structs
ARM: davinci: devices-da8xx: Add resource name for the McASP DMA request
ARM: OMAP2+: Remove legacy support for omap3 TouchBook
ARM: OMAP3: Remove legacy support for devkit8000
ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
ARM: shmobile: Consolidate the pm code for R-Car Gen2
ARM: shmobile: r8a7791: Correct SYSCIER value
ARM: shmobile: r8a7790: Correct SYSCIER value
ARM: at91: remove old setup
ARM: at91: sama5d4: remove useless map_io
ARM: at91: sama5 use SoC detection infrastructure
...
Here's the usual "low-priority fixes that didn't make it into the last
few -rcs, with a twist: We had a fixes pull request that I didn't send
in time to get into 4.0, so we'll send some of them to Greg for -stable as
well.
Contents here is as usual not all that controversial:
- A handful of randconfig fixes from Arnd, in particular for older Samsung
platforms
- Exynos fixes, !SMP building, DTS updates for MMC and lid switch
- Kbuild fix to create output subdirectory for DTB files
- Misc minor fixes for OMAP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o/4N
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's the usual "low-priority fixes that didn't make it into the last
few -rcs, with a twist: We had a fixes pull request that I didn't send
in time to get into 4.0, so we'll send some of them to Greg for
-stable as well.
Contents here is as usual not all that controversial:
- a handful of randconfig fixes from Arnd, in particular for older
Samsung platforms
- Exynos fixes, !SMP building, DTS updates for MMC and lid switch
- Kbuild fix to create output subdirectory for DTB files
- misc minor fixes for OMAP"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: at91/dt: sama5d3 xplained: add phy address for macb1
kbuild: Create directory for target DTB
ARM: mvebu: Disable CPU Idle on Armada 38x
ARM: DRA7: Enable Cortex A15 errata 798181
ARM: dts: am57xx-beagle-x15: Add thermal map to include fan and tmp102
ARM: dts: DRA7: Add bandgap and related thermal nodes
bus: ocp2scp: SYNC2 value should be changed to 0x6
ARM: dts: am4372: Add "ti,am437x-ocp2scp" as compatible string for OCP2SCP
ARM: OMAP2+: remove superfluous NULL pointer check
ARM: EXYNOS: Fix build breakage cpuidle on !SMP
ARM: dts: fix lid and power pin-functions for exynos5250-spring
ARM: dts: fix mmc node updates for exynos5250-spring
ARM: OMAP4: remove dead kconfig option OMAP4_ERRATA_I688
MAINTAINERS: add OMAP defconfigs under OMAP SUPPORT
ARM: OMAP1: PM: fix some build warnings on 1510-only Kconfigs
ARM: cns3xxx: don't export static symbol
ARM: S3C24XX: avoid a Kconfig warning
ARM: S3C24XX: fix header file inclusions
ARM: S3C24XX: fix building without PM_SLEEP
ARM: S3C24XX: use SAMSUNG_WAKEMASK for s3c2416
...
