DDR52 with 8-bit mode should be handled in a different way when
requesting ciu_clk. However DDR50 is used for SDMMC/SDIO and
could never be possible with 8-bit mode. It's trival but misleading.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cadence sent out an errata report to their customers of this IP.
This errata is not so severe, but the tune request should be sent
twice to avoid the potential issue.
Quote from the report:
Problem Summary
---------------
The IP6116 SD/eMMC PHY design has a timing issue on receive data path.
This issue may lead to an incorrect values of read/write pointers of
the synchronization FIFO. Such a situation can happen at the SDR104
and HS200 tuning procedure when the PHY is requested to change a phase
of sampling clock when moving to the next tuning iteration.
Workarounds
-----------
The following are valid workarounds to resolve the issue:
1. In eMMC mode, software sends tune request twice instead of once at
each iteration. This means that the clock phase is not changed on
the second request so there is no potential for clock instability.
2. In SD mode, software must not use the hardware tuning and instead
perform an almost identical procedure to eMMC, using the HRS34 Tune
Force register.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Explicitly update the docomentation to support the Meson-AXG platform.
Signed-off-by: Nan Li <nan.li@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Introduce the compatible data to cover the register offset & mask
change of the eMMC controller in Amlogic's Meson-AXG SoC.
Signed-off-by: Nan Li <nan.li@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Since RPMB area is accessible via special ioctl only and boot areas
are unlikely to contain any partitions, exclude them all from listing
in /proc/partitions. This will hide them from various user-level
software (e.g. fdisk), thus avoiding unnecessary access attempts.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace dma_request_channel() with dma_request_chan(),
which also supports probing from the devicetree.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for the JZ4780 MMC controller to the jz47xx_mmc driver. There
are a few minor differences from the 4740 to the 4780 that need to be
handled, but otherwise the controllers behave the same. The IREG and IMASK
registers are expanded to 32 bits. Additionally, some error conditions are
now reported in both STATUS and IREG. Writing IREG before reading STATUS
causes the bits in STATUS to be cleared, so STATUS must be read first to
ensure we see and report error conditions correctly.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The maximum clock rate can be overridden by DT. The clock rate should
be set to the DT-specified value rather than the constant JZ_MMC_CLK_RATE
when this is done. If the maximum clock rate is not set by DT then
mmc->f_max will be set to JZ_MMC_CLK_RATE.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support to probe the device via devicetree, which
will be used to support other SoCs such as the JZ4780.
Based on commits from the CI20 repo, by Paul Cercueil
and Alex Smith. Binding document based on work by
Zubair Lutfullah Kakakhel.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case a bootloader leaves the device in a bad state,
requesting the interrupt before resetting results in a bad
interrupt loop.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
[Ezequiel: cleanup commit description]
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of accessing the platform data pointer directly,
use the dev_get_platdata() helper.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Just a minor cleanup to order the headers alphabetically.
This helps prevent merge conflicts.
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, if jz4740_mmc_request_gpios() fails, the driver
tries to release DMA resources. This is wrong because DMA
is requested at a later stage.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
[Ezequiel: cleanup commit message]
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The use of stack Variable Length Arrays needs to be avoided, as they
can be a vector for stack exhaustion, which can be both a runtime bug
(kernel Oops) or a security flaw (overwriting memory beyond the
stack). Also, in general, as code evolves it is easy to lose track of
how big a VLA can get. Thus, we can end up having runtime failures
that are hard to debug. As part of the directive[1] to remove all VLAs
from the kernel, and build with -Wvla.
Currently driver is using a VLA declared using the number of descriptors. This
array is used to store integer values and is later used as an argument to
`gpiod_set_array_value_cansleep()` This can be avoided by using
`kmalloc_array()` to allocate memory for the array of integer values. Memory is
free'd before return from function.
>From the code it appears that it is safe to sleep so we can use GFP_KERNEL
(based _cansleep() suffix of function `gpiod_set_array_value_cansleep()`.
It can be expected that this patch will result in a small increase in overhead
due to the use of `kmalloc_array()`
[1] https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On SD 2.00 cards we get lots of these messages:
"mmc0: Got data interrupt 0x00000002 even though no data operation was in progress"
By applying the SDHCI_QUIRK2_STOP_WITH_TC quirk, the messages no longer happen.
A single card claiming to be SD 3.00 compliant also generates the interrupts,
but since the card's manfacturing date is 2002 mar, it's unlikely to really be
SD 3.00. This card is a 8GB SanDisk 'SU08G' 8.0 (SDHC class 4).
This has been reported on Xilinx devices that also use the Arasan IP.
See https://patchwork.kernel.org/patch/8062871/
This has been tested on the Renesas RZ/ND-DB board with the RZ/N1 SoC. The
Arasan IP in this device is version 1.39a and uses a max SD clock of 50MHz and
does not support DDR modes.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- sdhci-pci: Fixup tuning for AMD for eMMC HS200 mode
- renesas_sdhi_internal_dmac: Avoid data corruption by limiting DMA RX
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jO/Y
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"A couple of MMC host fixes:
- sdhci-pci: Fixup tuning for AMD for eMMC HS200 mode
- renesas_sdhi_internal_dmac: Avoid data corruption by limiting
DMA RX"
* tag 'mmc-v4.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: renesas_sdhi_internal_dmac: limit DMA RX for old SoCs
mmc: sdhci-pci: Only do AMD tuning for HS200
Early revisions of certain SoCs cannot do multiple DMA RX streams in
parallel. To avoid data corruption, only allow one DMA RX channel and
fall back to PIO, if needed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit c31165d740 ("mmc: sdhci-pci: Add support for HS200 tuning mode
on AMD, eMMC-4.5.1") added a HS200 tuning method for use with AMD SDHCI
controllers. As described in the commit subject, this tuning is specific
for HS200. However, as implemented, this method is used for all host
timings, because platform_execute_tuning, if it exists, is called
unconditionally by sdhci_execute_tuning(). This breaks tuning when using
the AMD controller with, for example, a DDR50 SD card.
Instead, we can implement an amd execute_tuning wrapper callback, and
then conditionally do the HS200 specific tuning for HS200, and otherwise
call back to the standard sdhci_execute_tuning().
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: c31165d740 ("mmc: sdhci-pci: Add support for HS200 tuning mode on AMD, eMMC-4.5.1")
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RVhK
-----END PGP SIGNATURE-----
Merge tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"It's a pretty quiet round this time, which is nice. This contains:
- series from Bart, cleaning up the way we set/test/clear atomic
queue flags.
- series from Bart, fixing races between gendisk and queue
registration and removal.
- set of bcache fixes and improvements from various folks, by way of
Michael Lyle.
- set of lightnvm updates from Matias, most of it being the 1.2 to
2.0 transition.
- removal of unused DIO flags from Nikolay.
- blk-mq/sbitmap memory ordering fixes from Omar.
- divide-by-zero fix for BFQ from Paolo.
- minor documentation patches from Randy.
- timeout fix from Tejun.
- Alpha "can't write a char atomically" fix from Mikulas.
- set of NVMe fixes by way of Keith.
- bsg and bsg-lib improvements from Christoph.
- a few sed-opal fixes from Jonas.
- cdrom check-disk-change deadlock fix from Maurizio.
- various little fixes, comment fixes, etc from various folks"
* tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block: (139 commits)
blk-mq: Directly schedule q->timeout_work when aborting a request
blktrace: fix comment in blktrace_api.h
lightnvm: remove function name in strings
lightnvm: pblk: remove some unnecessary NULL checks
lightnvm: pblk: don't recover unwritten lines
lightnvm: pblk: implement 2.0 support
lightnvm: pblk: implement get log report chunk
lightnvm: pblk: rename ppaf* to addrf*
lightnvm: pblk: check for supported version
lightnvm: implement get log report chunk helpers
lightnvm: make address conversions depend on generic device
lightnvm: add support for 2.0 address format
lightnvm: normalize geometry nomenclature
lightnvm: complete geo structure with maxoc*
lightnvm: add shorten OCSSD version in geo
lightnvm: add minor version to generic geometry
lightnvm: simplify geometry structure
lightnvm: pblk: refactor init/exit sequences
lightnvm: Avoid validation of default op value
lightnvm: centralize permission check for lightnvm ioctl
...
If an error was detected when CMD23 was issued, command sequence should
be terminated with errors and CMD23 should be issued after retuning.
Fixes: 8b22c3c18b ("mmc: tmio: add CMD23 support")
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: <stable@vger.kernel.org> # 4.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Upon module load, mmc_block allocates a bus with bus_registeri() in
mmc_blk_init(). This reference never gets freed during module unload, which
leads to subsequent re-insertions of the module fails and a WARN() splat is
triggered.
Fix the bug by dropping the reference for the bus in mmc_blk_exit().
Signed-off-by: Alexander Kappner <agk@godking.net>
Fixes: 97548575be ("mmc: block: Convert RPMB to a character device")
Cc: <stable@vger.kernel.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A spinlock is held while updating the internal copy of the IRQ mask,
but not while writing it to the actual IMASK register. After the lock
is released, an IRQ can occur before the IMASK register is written.
If handling this IRQ causes the mask to be changed, when the handler
returns back to the middle of the first mask update, a stale value
will be written to the mask register.
If this causes an IRQ to become unmasked that cannot have its status
cleared by writing a 1 to it in the IREG register, e.g. the SDIO IRQ,
then we can end up stuck with the same IRQ repeatedly being fired but
not handled. Normally the MMC IRQ handler attempts to clear any
unexpected IRQs by writing IREG, but for those that cannot be cleared
in this way then the IRQ will just repeatedly fire.
This was resulting in lockups after a while of using Wi-Fi on the
CI20 (GitHub issue #19).
Resolve by holding the spinlock until after the IMASK register has
been updated.
Cc: stable@vger.kernel.org
Link: https://github.com/MIPS/CI20_linux/issues/19
Fixes: 61bfbdb856 ("MMC: Add support for the controller on JZ4740 SoCs.")
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Export host capabilities through debugfs
- Export card RCA register via sysfs
- Improve card initializing sequence while enabling 4-bit bus
- Export a function to enable/disable wakeup for card detect IRQ
MMC host:
- dw_mmc: Add support for new hi3798cv200 variant
- dw_mmc: Remove support for some deprecated DT properties
- mediatek: Add support for new variant used on MT7622 SoC
- sdhci: Improve wakeup support for SDIO IRQs
- sdhci: Improve wakeup support for card detect IRQs
- sdhci-omap: Add tuning support
- sdhci_omap: Add UHS-I mode support
- sunxi: Prepare for runtime PM support via a few re-factorings
- tmio: deprecate "toshiba,mmc-wrprotect-disable" DT property
- tmio/renesas_sdhi: Consolidate code supporting write protect
- tmio: Improve DMA vs PIO handling
- tmio: Add support for IP-builtin card detection logic
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJaw0MuAAoJEP4mhCVzWIwpW78P/2N2qPt21OfvnIbSexY1nyPd
5+rjScgy+oTUnNxITA9LOnM4P6Wg/9PgvhjUdNdHzd5ZaXIchw372+Xu6hZHdujI
vBfnpsI/xtyL1TQ6nvJc9b+Sp4W4LL2MlCqxi+btAKLvTAU3NNm7uJRRP6xRNDd5
8wcsCoIN4C3k5hmh5++DDLCfuzpwmbC1cEbGtL/QEV9xeCY5+fJq4Qpq14L2TJ0g
LeDls3X4HAJa3SsgSGOdNr8rttKUSS+j7i1XsShHMyq89DD21PJ8fvMhdzlXJub9
A4PatcOXALS/Xd2YVjeLHrRRlTitssD+Sllt46NsB4eJJOO+DempecY+i0WoW60y
p9IUSSX86yokGoyweiL2GI0Ja1Bg8xgdzTGVbfZ6w6UKHjQAcItnojyMghDM5+zt
VjDIU59rzm+BEDqcktsbGgLPjOZ0ZWgJPPp2NPkechxsojvCJ9Smm6yPjzaUnZ60
U9PxsYbs4NB+nE9iKDioyA1ABP0N+BloUkTf/cVHdPBBPMmOyI7jYEDS7mqollZU
bQCFx+BqcQMbnvI/TZxNDTr4HsiyiXJa0GTCB77sge8tZdcUTjUsWyhc+BYpIqgA
68/dlwTcawSXDliup5XxtYcAjGugtHbPnS/39uBXvscqWVej1WI5RTyzKdC/hnos
BP5uz0K1Wic1Dl+jqlWc
=2Pd6
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Export host capabilities through debugfs
- Export card RCA register via sysfs
- Improve card initializing sequence while enabling 4-bit bus
- Export a function to enable/disable wakeup for card detect IRQ
MMC host:
- dw_mmc: Add support for new hi3798cv200 variant
- dw_mmc: Remove support for some deprecated DT properties
- mediatek: Add support for new variant used on MT7622 SoC
- sdhci: Improve wakeup support for SDIO IRQs
- sdhci: Improve wakeup support for card detect IRQs
- sdhci-omap: Add tuning support
- sdhci_omap: Add UHS-I mode support
- sunxi: Prepare for runtime PM support via a few re-factorings
- tmio: deprecate "toshiba,mmc-wrprotect-disable" DT property
- tmio/renesas_sdhi: Consolidate code supporting write protect
- tmio: Improve DMA vs PIO handling
- tmio: Add support for IP-builtin card detection logic"
* tag 'mmc-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (55 commits)
mmc: renesas_sdhi: replace EXT_ACC with HOST_MODE
mmc: update sdio_claim_irq documentation
mmc: Export host capabilities to debugfs.
mmc: core: Disable HPI for certain Micron (Numonyx) eMMC cards
mmc: block: fix updating ext_csd caches on ioctl call
mmc: sunxi: Set our device drvdata earlier
mmc: sunxi: Move the reset deassertion before enabling the clocks
mmc: sunxi: Move resources management to separate functions
mmc: dw_mmc: add support for hi3798cv200 specific extensions of dw-mshc
dt-bindings: mmc: add bindings for hi3798cv200-dw-mshc
mmc: core: Export card RCA register via sysfs
mmc: renesas_sdhi: fix WP detection
mmc: core: Use memdup_user() rather than duplicating its implementation
mmc: dw_mmc-rockchip: correct property names in debug
mmc: sd: Remove redundant err assignment from mmc_read_switch
mmc: sdio: Check the return value of sdio_enable_4bit_bus
mmc: core: Don't try UHS-I mode if 4-bit mode isn't supported
arm64: dts: hi3660: remove 'num-slots' property for dwmmc
ARM: dts: lpc18xx: remove 'num-slots' property for dwmmc
arm64: dts: stratix10: remove 'num-slots' property for dwmmc
...
This removes the entire architecture code for blackfin, cris, frv, m32r,
metag, mn10300, score, and tile, including the associated device drivers.
I have been working with the (former) maintainers for each one to ensure
that my interpretation was right and the code is definitely unused in
mainline kernels. Many had fond memories of working on the respective
ports to start with and getting them included in upstream, but also saw
no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company
in charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
that all the SoC product lines are still around, but have not used the
custom CPU architectures for several years at this point. In contrast,
CPU instruction sets that remain popular and have actively maintained
kernel ports tend to all be used across multiple licensees.
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I made
sure that they are all unused. Some architectures (notably tile, mn10300,
and blackfin) are still being shipped in products with old kernels,
but those products will never be updated to newer kernel releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing their
support or getting it added to mainline gcc in the first place.
They all have patched gcc-7.3 ports that work to some degree, but
complete upstream support won't happen before gcc-8.1. Csky posted
their first kernel patch set last week, their situation will be similar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fQ8z
-----END PGP SIGNATURE-----
Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pul removal of obsolete architecture ports from Arnd Bergmann:
"This removes the entire architecture code for blackfin, cris, frv,
m32r, metag, mn10300, score, and tile, including the associated device
drivers.
I have been working with the (former) maintainers for each one to
ensure that my interpretation was right and the code is definitely
unused in mainline kernels. Many had fond memories of working on the
respective ports to start with and getting them included in upstream,
but also saw no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company in
charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
seems that all the SoC product lines are still around, but have not
used the custom CPU architectures for several years at this point. In
contrast, CPU instruction sets that remain popular and have actively
maintained kernel ports tend to all be used across multiple licensees.
[ See the new nds32 port merged in the previous commit for the next
generation of "one company in charge of an SoC line, a CPU
microarchitecture and a software ecosystem" - Linus ]
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I
made sure that they are all unused. Some architectures (notably tile,
mn10300, and blackfin) are still being shipped in products with old
kernels, but those products will never be updated to newer kernel
releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing
their support or getting it added to mainline gcc in the first
place. They all have patched gcc-7.3 ports that work to some
degree, but complete upstream support won't happen before gcc-8.1.
Csky posted their first kernel patch set last week, their situation
will be similar
[ Palmer Dabbelt points out that RISC-V support is in mainline gcc
since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]"
This really says it all:
2498 files changed, 95 insertions(+), 467668 deletions(-)
* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
MAINTAINERS: UNICORE32: Change email account
staging: iio: remove iio-trig-bfin-timer driver
tty: hvc: remove tile driver
tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
serial: remove tile uart driver
serial: remove m32r_sio driver
serial: remove blackfin drivers
serial: remove cris/etrax uart drivers
usb: Remove Blackfin references in USB support
usb: isp1362: remove blackfin arch glue
usb: musb: remove blackfin port
usb: host: remove tilegx platform glue
pwm: remove pwm-bfin driver
i2c: remove bfin-twi driver
spi: remove blackfin related host drivers
watchdog: remove bfin_wdt driver
can: remove bfin_can driver
mmc: remove bfin_sdh driver
input: misc: remove blackfin rotary driver
input: keyboard: remove bf54x driver
...
The blackfin architecture is getting removed, so this one
is obsolete now as well.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
All our documentation says HOST_MODE, we don't really know where EXT_ACC
came from. Rename it to reduce the confusion.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Update documentation for sdio_claim_irq to downgrade the wording
about doing recursive claims in an IRQ handler from 'must not' to
'should not'. This clarifies that recursive claims are supported,
but not the recommended (best) practice
Signed-off-by: Joel Cunningham <joel.cunningham@garmin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch exports the host capabilities to debugfs
Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
[Harish: Added caps2, moved creation to mmc_add_host_debugfs]
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Zero is a valid IRQ number and is being used on some CHT tablets. Stop
treating it as an error.
Reported-by: Luke Ross <luke@lukeross.name>
Fixes: 1b7ba57ecc ("mmc: sdhci-acpi: Handle return value of platform_get_irq")
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was found that in IDMAC mode after soft-reset driver switches
to PIO mode.
That's what happens in case of DTO timeout overflow calculation failure:
1. soft-reset is called
2. driver restarts dma
3. descriptors states are checked, one of descriptor is owned by the IDMAC.
4. driver can't use DMA and then switches to PIO mode.
Failure was already fixed in:
https://www.spinics.net/lists/linux-mmc/msg48125.html.
Behaviour while soft-reset is not something we except or
even want to happen. So we switch from dw_mci_idmac_reset
to dw_mci_idmac_init, so descriptors are cleaned before starting dma.
And while at it explicitly zero des0 which otherwise might
contain garbage as being allocated by dmam_alloc_coherent().
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: linux-snps-arc@lists.infradead.org
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Certain Micron eMMC v4.5 cards might get broken when HPI feature is used
and hence this patch disables the HPI feature for such buggy cards.
In U-Boot, these cards are reported as
Manufacturer: Micron (ID: 0xFE)
OEM: 0x4E
Name: MMC32G
Revision: 19 (0x13)
Serial: 959241022 Manufact. date: 8/2015 (0x82) CRC: 0x00
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.5
High Capacity: Yes
Capacity: 29.1 GiB
Boot Partition Size: 16 MiB
Bus Width: 8-bit
According to JEDEC JEP106 manufacturer 0xFE is Numonyx, which was bought by
Micron.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Cc: <stable@vger.kernel.org> # 4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
PARTITION_CONFIG is cached in mmc_card->ext_csd.part_config and the
currently active partition in mmc_blk_data->part_curr. These caches do
not always reflect changes if the ioctl call modifies the
PARTITION_CONFIG registers, e.g. by changing BOOT_PARTITION_ENABLE.
Write the PARTITION_CONFIG value extracted from the ioctl call to the
cache and update the currently active partition accordingly. This
ensures that the user space cannot change the values behind the
kernel's back. The next call to mmc_blk_part_switch() will operate on
the data set by the ioctl and reflect the changes appropriately.
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As soon as the pm_runtime_enable hook is called, our runtime_suspend and
runtime_resume hooks can be called as well. However, we only set the device
drvdata that we will use after we have registered into the MMC core. Move
that earlier so that we don't have a race that could lead to a crash.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As per Allwinner guidelines, the reset line should be deasserted before
turning the clocks on.
Implement it in our driver as well.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We've had all our resources management, and especially the clocks and reset
sequence, done directly as part of the probe.
As we want to implement runtime_pm, we'll obviously want to have that
moved outside of the probe so that we can call do it in our runtime suspend
and resume hooks without too much duplication.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hi3798CV200 SoC extends the dw-mshc controller for additional clock
and bus control. Add support for these extensions.
Signed-off-by: tianshuliang <tianshuliang@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch exports RCA register to sysfs which will help in reading the
disk identification information.
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Certain Micron eMMC v4.5 cards might get broken when HPI feature is used
and hence this patch disables the HPI feature for such buggy cards.
In U-Boot, these cards are reported as
Manufacturer: Micron (ID: 0xFE)
OEM: 0x4E
Name: MMC32G
Revision: 19 (0x13)
Serial: 959241022 Manufact. date: 8/2015 (0x82) CRC: 0x00
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.5
High Capacity: Yes
Capacity: 29.1 GiB
Boot Partition Size: 16 MiB
Bus Width: 8-bit
According to JEDEC JEP106 manufacturer 0xFE is Numonyx, which was bought by
Micron.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Cc: <stable@vger.kernel.org> # 4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Before enabling the clock, dwmmc exynos driver is trying to access the
register. Then the kernel panic can be occurred.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
PARTITION_CONFIG is cached in mmc_card->ext_csd.part_config and the
currently active partition in mmc_blk_data->part_curr. These caches do
not always reflect changes if the ioctl call modifies the
PARTITION_CONFIG registers, e.g. by changing BOOT_PARTITION_ENABLE.
Write the PARTITION_CONFIG value extracted from the ioctl call to the
cache and update the currently active partition accordingly. This
ensures that the user space cannot change the values behind the
kernel's back. The next call to mmc_blk_part_switch() will operate on
the data set by the ioctl and reflect the changes appropriately.
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit "mmc: renesas_sdhi: use MMC_CAP2_NO_WRITE_PROTECT instead of
TMIO own flag" activated MMC_CAP2_NO_WRITE_PROTECT for Renesas SDHI
which incorrectly disabled WP altogether instead of only disabling the
internal mechanism. Since the whole WP handling has been reworked, we
can simply disable this capability to re-enable WP GPIOs.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Following up the device tree fixed in commits e78c637127 ("ARM: dts:
rockchip: Fix DWMMC clocks") and ca9eee95a2 ("arm64: dts: rockchip:
Fix DWMMC clocks", 2018-02-15), avoid confusion by using the correct
property name in the debug output if clocks are not found.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Variable err would be firstly initialized by the return value of
mmc_sd_switch().
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
