Andrew Lunn says:
====================
Use MMD/C45 helpers
MDIO busses can perform two sorts of bus transaction, defined in
clause 22 and clause 45 of 802.3. This results in two register
addresses spaces. The current driver structure for indicating if C22
or C45 should be used is messy, and many C22 only bus drivers will
wrongly interpret a C45 transaction as a C22 transaction.
This patchset is a preparation step to cleanup the situation. It
converts MDIO bus users to make use of existing _mmd and _c45 helpers
to perform accesses to C45 registers. This will later allow C45 and
C22 to be kept separate.
====================
Link: https://lore.kernel.org/r/20220430173037.156823-1-andrew@lunn.ch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stop using the helpers to construct a special mdio address which
indicates C45. Instead use the C45 accessors, which will call the
busses C45 specific read/write API.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stop using the helpers to construct a special phy address which
indicates C45. Instead use the C45 accessors, which will call the
busses C45 specific read/write API.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Rather than construct special phy device addresses to access C45
registers, use the mmd helpers. These will directly call the C45 API
of the MDIO bus driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stop using the helpers to construct a special phy address which
indicates C45. Instead use the C45 accessors, which will call the
busses C45 specific read/write API.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stop using the helpers to construct a special phy address which
indicates C45. Instead use the C45 accessors, which will call the
busses C45 specific read/write API.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEBsvAIBsPu6mG7thcrX5LkNig010FAmJvh3QTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCtfkuQ2KDTXfFkB/45BPO6VByqNu+kFIDK1wU+m2GFIIRE
zvWyz8gc1fHxmekZaMVYnRYBbXOOwbRqlrVGnUUT9bfYKvE49aPQRFU1xkZB9rmi
bH84u8s4JW0BgexZ6szIlsN4IFa64Sr4lOqqvdAQ9hBYolXt4CE+eBWW51JBkFkN
WwTgUqaieyib3g7H4vXJvEjK15wJvGWXnRYHt/BV1mSxyUXe3MesspoE4u1/KH89
gVtuAjjG7LcKZCqF79XQA5vNYGJ9OK2c2eThFgfsG3DfhzNsp6n2gI4m5cKg7DLK
FQoad/xBh+Vf06snrNIqP1fqfH2mLOVFmZ+QZLAJ0WxPHAsUBg8LLhtr
=oTur
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.19-20220502' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2022-05-02
this is a pull request of 9 patches for net-next/master.
The first patch is by Biju Das and documents renesas,r9a07g043-canfd
support in the renesas,rcar-canfd bindings document.
Jakub Kicinski's patch removes a copy of the NAPI_POLL_WEIGHT define
from the m_can driver.
The last 7 patches all target the ctucanfd driver. Pavel Pisa provides
2 patch which update the documentation. 2 patches by Jiapeng Chong
remove unneeded includes and error messages. And another 3 patches by
Pavel Pisa to further clean up the driver (remove inline keyword,
remove unneeded debug statements, and remove unneeded module parameters).
linux-can-next-for-5.19-20220502
* tag 'linux-can-next-for-5.19-20220502' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: ctucanfd: remove PCI module debug parameters
can: ctucanfd: remove debug statements
can: ctucanfd: remove inline keyword from local static functions
can: ctucanfd: ctucan_platform_probe(): remove unnecessary print function dev_err()
can: ctucanfd: remove unused including <linux/version.h>
docs: networking: device drivers: can: ctucanfd: update author e-mail
docs: networking: device drivers: can: add ctucanfd to index
can: m_can: remove a copy of the NAPI_POLL_WEIGHT define
dt-bindings: can: renesas,rcar-canfd: Document RZ/G2UL support
====================
Link: https://lore.kernel.org/r/20220502075914.1905039-1-mkl@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
VxLAN belongs to UDP-based encapsulation protocol. Inner TSO for VxLAN
packet with udpcsum requires offloading of outer header csum.
The device doesn't support outer header csum offload. However, inner TSO
for VxLAN with udpcsum can still work with GSO_PARTIAL offload, which
means outer udp csum computed by stack and inner tcp segmentation finished
by hardware. Thus, the patch enable features "NETIF_F_GSO_UDP_TUNNEL_CSUM"
and "NETIF_F_GSO_PARTIAL" and set gso_partial_features.
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220430231150.175270-1-simon.horman@corigine.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add a boilerplate test loop to run all tests in
vrf_strict_mode_test.sh. Add a -t flag that allows a selected test to
run. Remove the vrf_strict_mode_tests function which is now unused.
Signed-off-by: Jaehee Park <jhpark1013@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220429164658.GA656707@jaehee-ThinkPad-X1-Extreme
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Peilin Ye says:
====================
devices always NETIF_F_LLTX
v1: https://lore.kernel.org/netdev/cover.1650580763.git.peilin.ye@bytedance.com/
change since v1:
- deleted "depends on patch..." in [1/2]'s commit message
This patchset depends on these fixes [1], which has been merged into
net-next. Since o_seqno is now atomic_t, we can always turn on
NETIF_F_LLTX for [IP6]GRE[TAP] devices, since we no longer need the TX
lock (&txq->_xmit_lock).
We could probably do the same thing to [IP6]ERSPAN devices as well, but
I'm not familiar with them yet. For example, ERSPAN devices are
initialized as |= GRE_FEATURES in erspan_tunnel_init(), but I don't see
IP6ERSPAN devices being initialized as |= GRE6_FEATURES. Where should we
initialize IP6ERSPAN devices' ->features? Please suggest if I'm missing
something, thanks!
[1] https://lore.kernel.org/netdev/cover.1650575919.git.peilin.ye@bytedance.com/
====================
Link: https://lore.kernel.org/r/cover.1651207788.git.peilin.ye@bytedance.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Recently we made o_seqno atomic_t. Stop special-casing TUNNEL_SEQ, and
always mark IP6GRE[TAP] devices as NETIF_F_LLTX, since we no longer need
the TX lock (&txq->_xmit_lock).
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Recently we made o_seqno atomic_t. Stop special-casing TUNNEL_SEQ, and
always mark GRE[TAP] devices as NETIF_F_LLTX, since we no longer need
the TX lock (&txq->_xmit_lock).
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The print function dev_err() is redundant because platform_get_irq()
already prints an error.
Eliminate the follow coccicheck warnings:
| drivers/net/can/ctucanfd/ctucanfd_platform.c:67:2-9:
| line 67 is redundant because platform_get_irq() already prints an error.
Link: https://lore.kernel.org/all/20220421203242.7335-1-jiapeng.chong@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Pave Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Defining local versions of NAPI_POLL_WEIGHT with the same values in
the drivers just makes refactoring harder.
Link: https://lore.kernel.org/all/20220429174446.196655-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Alexandru Tachici says:
====================
net: phy: adin1100: Add initial support for ADIN1100 industrial PHY
The ADIN1100 is a low power single port 10BASE-T1L transceiver designed for
industrial Ethernet applications and is compliant with the IEEE 802.3cg
Ethernet standard for long reach 10 Mb/s Single Pair Ethernet.
The ADIN1100 uses Auto-Negotiation capability in accordance
with IEEE 802.3 Clause 98, providing a mechanism for
exchanging information between PHYs to allow link partners to
agree to a common mode of operation.
The concluded operating mode is the transmit amplitude mode and
master/slave preference common across the two devices.
Both device and LP advertise their ability and request for
increased transmit at:
- BASE-T1 autonegotiation advertisement register [47:32]\
Clause 45.2.7.21 of Standard 802.3
- BIT(13) - 10BASE-T1L High Level Transmit Operating Mode Ability
- BIT(12) - 10BASE-T1L High Level Transmit Operating Mode Request
For 2.4 Vpp (high level transmit) operation, both devices need
to have the High Level Transmit Operating Mode Ability bit set,
and only one of them needs to have the High Level Transmit
Operating Mode Request bit set. Otherwise 1.0 Vpp transmit level
will be used.
Settings for eth1:
Supported ports: [ TP MII ]
Supported link modes: 10baseT1L/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT1L/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT1L/Full
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 10Mb/s
Duplex: Full
Auto-negotiation: on
master-slave cfg: preferred slave
master-slave status: slave
Port: Twisted Pair
PHYAD: 0
Transceiver: external
MDI-X: Unknown
Link detected: yes
SQI: 7/7
1. Add basic support for ADIN1100.
Alexandru Ardelean (1):
net: phy: adin1100: Add initial support for ADIN1100 industrial PHY
1. Added 10baset-T1L link modes.
2. Added 10-BasetT1L registers.
3. Added Base-T1 auto-negotiation registers. For Base-T1 these
registers decide master/slave status and TX voltage of the
device and link partner.
4. Added 10BASE-T1L support in phy-c45.c. Now genphy functions will call
Base-T1 functions where registers don't match, like the auto-negotiation ones.
5. Convert MSE to SQI using a predefined table and allow user access
through ethtool.
6. DT bindings for the 2.4 Vpp transmit mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a tristate property to advertise desired transmit level.
If the device supports the 2.4 Vpp operating mode for 10BASE-T1L,
as defined in 802.3gc, and the 2.4 Vpp transmit voltage operation
is desired, property should be set to 1. This property is used
to select whether Auto-Negotiation advertises a request to
operate the 10BASE-T1L PHY in increased transmit level mode.
If property is set to 1, the PHY shall advertise a request
to operate the 10BASE-T1L PHY in increased transmit level mode.
If property is set to zero, the PHY shall not advertise
a request to operate the 10BASE-T1L PHY in increased transmit level mode.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Determine the SQI from MSE using a predefined table
for the 10BASE-T1L.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADIN1100 is a low power single port 10BASE-T1L transceiver designed for
industrial Ethernet applications and is compliant with the IEEE 802.3cg
Ethernet standard for long reach 10 Mb/s Single Pair Ethernet.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is needed because the BASE-T1 uses different registers
for status, control and advertisement to those already
employed in the existing phy-c45 functions.
Where required, genphy_c45 functions will now check whether
the device supports BASE-T1 and use the specific registers
instead: 45.2.7.19 BASE-T1 AN control register,
45.2.7.20 BASE-T1 AN status, 45.2.7.21 BASE-T1 AN
advertisement register, 45.2.7.22 BASE-T1 AN LP Base
Page ability register, 45.2.1.185 BASE-T1 PMA/PMD control
register.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added BASE-T1 AN advertisement register (Registers 7.514, 7.515, and
7.516) and BASE-T1 AN LP Base Page ability register (Registers 7.517,
7.518, and 7.519).
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 802.3gc specification defines the 10-BaseT1L link
mode for ethernet trafic on twisted wire pair.
PMA status register can be used to detect if the phy supports
2.4 V TX level and PCS control register can be used to
enable/disable PCS level loopback.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add entry for the 10base-T1L full duplex mode.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All but 5 methods in dsa_swith_ops use tabs for indentation.
Change the 5 methods that break this rule.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
veth netdevice defines own rx queues and allocates array containing
up to 4095 ~750-bytes-long 'struct veth_rq' elements. Such allocation
is quite huge and should be accounted to memcg.
Signed-off-by: Vasily Averin <vvs@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Begunkov says:
====================
UDP sock_wfree optimisations
The series is not UDP specific but that the main beneficiary. 2/3 saves one
atomic in sock_wfree() and on top 3/3 removes an extra barrier.
Tested with UDP over dummy netdev, 2038491 -> 2099071 req/s (or around +3%).
note: in regards to 1/3, there is a "Should agree with poll..." comment
that I don't completely get, and there is no git history to explain it.
Though I can't see how it could rely on having the second check without
racing with tasks woken by wake_up*().
The series was split from a larger patchset, see
https://lore.kernel.org/netdev/cover.1648981570.git.asml.silence@gmail.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we have a separate path for sock_def_write_space() and can go one
step further. When it's called from sock_wfree() we know that there is a
preceding atomic for putting down ->sk_wmem_alloc. We can use it to
replace to replace smb_mb() with a less expensive
smp_mb__after_atomic(). It also removes an extra RCU read lock/unlock as
a small bonus.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For non SOCK_USE_WRITE_QUEUE sockets, sock_wfree() (atomically) puts
->sk_wmem_alloc twice. It's needed to keep the socket alive while
calling ->sk_write_space() after the first put.
However, some sockets, such as UDP, are freed by RCU
(i.e. SOCK_RCU_FREE) and use already RCU-safe sock_def_write_space().
Carve a fast path for such sockets, put down all refs in one go before
calling sock_def_write_space() but guard the socket from being freed
by an RCU read section.
note: because TCP sockets are marked with SOCK_USE_WRITE_QUEUE it
doesn't add extra checks in its path.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Except for minor rounding differences the first ->sk_wmem_alloc test in
sock_def_write_space() is a hand coded version of sock_writeable().
Replace it with the helper, and also kill the following if duplicating
the check.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With some SFP modules, such as Finisar FCLF8522P2BTL, the PHY hardware
strapping defaults to 1000BaseX mode, but the kernel prefers to set them
for SGMII mode. When this happens and the PHY is soft reset, the BMSR
status register is updated, but this happens after the kernel has already
read the PHY abilities during probing. This results in support not being
detected for, and the PHY not advertising support for, 10 and 100 Mbps
modes, preventing the link from working with a non-gigabit link partner.
When the PHY is being configured for SGMII mode, call genphy_read_abilities
again in order to re-read the capabilities, and update the advertising
field accordingly.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting from the blamed commit, the lan966x build fails with the
following compilation error:
drivers/net/ethernet/microchip/lan966x/lan966x_ptp.c:342:9: error: implicit declaration of function ‘ptp_find_pin_unlocked’ [-Werror=implicit-function-declaration]
342 | pin = ptp_find_pin_unlocked(phc->clock, PTP_PF_EXTTS, 0);
The issue is that there is no stub function for ptp_find_pin_unlocked
in case CONFIG_PTP_1588_CLOCK is not selected. Therefore add one.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: f3d8e0a9c2 ("net: lan966x: Add support for PTP_PF_EXTTS")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defining local versions of NAPI_POLL_WEIGHT with the same
values in the drivers just makes refactoring harder.
This patch covers three more drivers which I missed in
commit 5f012b40ef ("eth: remove copies of the NAPI_POLL_WEIGHT define").
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch doesn't change any functionality.
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the return expression.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a desire to share the oclot_stats_layout struct outside of the
current vsc7514 driver. In order to do so, the length of the array needs to
be known at compile time, and defined in the struct ocelot and struct
felix_info.
Since the array is defined in a .c file and would be declared in the header
file via:
extern struct ocelot_stat_layout[];
the size of the array will not be known at compile time to outside modules.
To fix this, remove the need for defining the number of stats at compile
time and allow this number to be determined at initialization.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit f84af32cbc ("net: ip_queue_rcv_skb() helper")
I dropped the skb dst in tcp_data_queue().
This only dealt with so-called TCP input slow path.
When fast path is taken, tcp_rcv_established() calls
tcp_queue_rcv() while skb still has a dst.
This was mostly fine, because most dsts at this point
are not refcounted (thanks to early demux)
However, TCP packets sent over loopback have refcounted dst.
Then commit 68822bdf76 ("net: generalize skb freeing
deferral to per-cpu lists") came and had the effect
of delaying skb freeing for an arbitrary time.
If during this time the involved netns is dismantled, cleanup_net()
frees the struct net with embedded net->ipv6.ip6_dst_ops.
Then when eventually dst_destroy_rcu() is called,
if (dst->ops->destroy) ... triggers an use-after-free.
It is not clear if ip6_route_net_exit() lacks a rcu_barrier()
as syzbot reported similar issues before the blamed commit.
( https://groups.google.com/g/syzkaller-bugs/c/CofzW4eeA9A/m/009WjumTAAAJ )
Fixes: 68822bdf76 ("net: generalize skb freeing deferral to per-cpu lists")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Walle says:
====================
net: lan966x: remove PHY reset support
Remove the unneeded PHY reset node as well as the driver support for it.
This was already discussed [1] and I expect Microchip to Ack on this
removal. Since there is no user, no breakage is expected.
I'm not sure it this should go through net or net-next and if the patches
should have a Fixes: tag or not. In upstream linux there was never any user
of it, so there is no bug to be fixed. But OTOH if the schema fix isn't
backported, then there might be an older schema version still containing
the reset node. Thoughts?
The patches needed for the GPIO part are just waiting to be picked up by
Linus [2,3]. This patch and the GPIO parts are the last pieces of the
puzzle to get ethernet working on the LAN9668 on upstream linux.
[1] https://lore.kernel.org/netdev/20220330110210.3374165-1-michael@walle.cc/
[2] https://lore.kernel.org/linux-gpio/CACRpkdbxmN+SWt95aGHjA2ZGnN61aWaA7c5S4PaG+WePAj=htg@mail.gmail.com/
[3] https://lore.kernel.org/linux-gpio/20220420191926.3411830-1-michael@walle.cc/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY subsystem as well as the MIIM mdio driver (in case of the
integrated PHYs) will take care of the resets. A separate reset driver
isn't needed. There is no in-tree user of this feature. Remove the
support.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY reset was intended to be a phandle for a special PHY reset
driver for the integrated PHYs as well as any external PHYs. It turns
out, that the culprit is how the reset of the switch device is done.
In particular, the switch reset also affects other subsystems like
the GPIO and the SGPIO block and it happens to be the case that the
reset lines of the external PHYs are connected to a common GPIO line.
Thus as soon as the switch issues a reset during probe time, all the
external PHYs will go into reset because all the GPIO lines will
switch to input and the pull-down on that signal will take effect.
So even if there was a special PHY reset driver, it (1) won't fix
the root cause of the problem and (2) it won't fix all the other
consumers of GPIO lines which will also be reset.
It turns out, the Ocelot SoC has the same weird behavior (or the
lack of a dedicated switch reset) and there the problem is already
solved and all the bits and pieces are already there and this PHY
reset property isn't not needed at all.
There are no users of this binding. Just remove it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Begunkov says:
====================
generic net and ipv6 minor optimisations
1-3 inline simple functions that only reshuffle arguments possibly adding
extra zero args, and call another function. It was benchmarked before with
a bunch of extra patches, see for details
https://lore.kernel.org/netdev/cover.1648981570.git.asml.silence@gmail.com/
It may increase the binary size, but it's the right thing to do and at least
without modules it actually sheds some bytes for some standard-ish config.
text data bss dec hex filename
9627200 0 0 9627200 92e640 ./arch/x86_64/boot/bzImage
text data bss dec hex filename
9627104 0 0 9627104 92e5e0 ./arch/x86_64/boot/bzImage
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Throw neigh checks in ip6_finish_output2() under a single slow path if,
so we don't have the overhead in the hot path.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two callers of __ip6_finish_output(), both are in
ip6_finish_output(). We can combine the call sites into one and handle
return code after, that will inline __ip6_finish_output().
Note, error handling under NET_XMIT_CN will only return 0 if
__ip6_finish_output() succeded, and in this case it return 0.
Considering that NET_XMIT_SUCCESS is 0, it'll be returning exactly the
same result for it as before.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni