[ Upstream commit ba5284ebe4 ]
On R-Car V4H, all PLLs except PLL5 support Spread Spectrum and/or
Fractional Multiplication to reduce electromagnetic interference.
Add the SASYNCPER and SASYNCPERD[124] clocks, which are used as clock
sources for modules that must not be affected by Spread Spectrum and/or
Fractional Multiplication.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/d0f35c35e1f96c5a649ab477e7ba5d8025957cd0.1665147497.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffa20aa581 ]
There are few GPU clocks which are powering up the memories
and thus enable the FORCE_MEM_PERIPH always for these clocks
to force the periph_on signal to remain active during halt
state of the clock.
Fixes: a3cc092196 ("clk: qcom: Add Global Clock controller (GCC) driver for SC7280")
Fixes: 3e0f01d6c7 ("clk: qcom: Add graphics clock controller driver for SC7280")
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Signed-off-by: Satya Priya <quic_c_skakit@quicinc.com>
Link: https://lore.kernel.org/r/1666159535-6447-1-git-send-email-quic_c_skakit@quicinc.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9003f74f5 ]
As serial communication requires a clean clock signal, the High Speed
Serial Communication Interfaces with FIFO (HSCIF) is clocked by a clock
that is not affected by Spread Spectrum or Fractional Multiplication.
Hence change the parent clocks for the HSCIF modules from the S0D3_PER
clock to the SASYNCPERD1 clock (which has the same clock rate), cfr.
R-Car V4H Hardware User's Manual rev. 0.54.
Fixes: 0ab55cf183 ("clk: renesas: cpg-mssr: Add support for R-Car V4H")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/b7928abc8b9f53d5b06ec8624342f449de3d24ec.1665147497.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ff4ba9e37 ]
Add custom I2C accessors to this driver, since the regular I2C regmap ones
do not generate the exact I2C transfers required by the chip. On I2C write,
it is mandatory to send transfer length first, on read the chip returns the
transfer length in first byte. Instead of always reading back 8 bytes, which
is the default and also the size of the entire register file, set BCP register
to 1 to read out 1 byte which is less wasteful.
Fixes: 892e0ddea1 ("clk: rs9: Add Renesas 9-series PCIe clock generator driver")
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220929195521.284497-1-marex@denx.de
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c461c677a8 upstream.
Commit 8c193f4714 ("pwm: tegra: Optimize period calculation") updated
the period calculation in the Tegra PWM driver and now returns an error
if the period requested is less than minimum period supported. This is
breaking PWM support on various Tegra platforms. For example, on the
Tegra210 Jetson Nano platform this is breaking the PWM fan support and
probing the PWM fan driver now fails ...
pwm-fan pwm-fan: Failed to configure PWM: -22
pwm-fan: probe of pwm-fan failed with error -22
The problem is that the default parent clock for the PWM on Tegra210 is
a 32kHz clock and is unable to support the requested PWM period.
Fix PWM support on Tegra20, Tegra30, Tegra114, Tegra124 and Tegra210 by
updating the parent clock for the PWM to be the PLL_P.
Fixes: 8c193f4714 ("pwm: tegra: Optimize period calculation")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # TF101 T20
Tested-by: Antoni Aloy Torrens <aaloytorrens@gmail.com> # TF101 T20
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # TF201 T30
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # TF700T T3
Link: https://lore.kernel.org/r/20221010100046.6477-1-jonathanh@nvidia.com
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f690a4d7a8 ]
It was reported that RPi3[1] and RPi Zero 2W boards have issues with
the Bluetooth. It turns out that when switching from initial to
operation speed host and device no longer can talk each other because
host uses incorrect UART baud rate.
The UART driver used in this case is amba-pl011. Original fix, see
below Github link[2], was inside pl011 module, but somehow it didn't
look as the right place to fix. Beside that this original rounding
function is not exactly perfect for all possible clock values. So I
deiced to move the hack to the platform which actually need it.
The UART clock is initialised to be as close to the requested
frequency as possible without exceeding it. Now that there is a
clock manager that returns the actual frequencies, an expected
48MHz clock is reported as 47999625. If the requested baud rate
== requested clock/16, there is no headroom and the slight
reduction in actual clock rate results in failure.
If increasing a clock by less than 0.1% changes it from ..999..
to ..000.., round it up.
[1] https://bugzilla.suse.com/show_bug.cgi?id=1188238
[2] ab3f1b3953
Cc: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de>
Reviewed-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/20220912081306.24662-1-iivanov@suse.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30eaf02149 ]
The function zynqmp_pll_round_rate is used to find a most appropriate
PLL frequency which the hardware can generate according to the desired
frequency. For example, if the desired frequency is 297MHz, considering
the limited range from PS_PLL_VCO_MIN (1.5GHz) to PS_PLL_VCO_MAX (3.0GHz)
of PLL, zynqmp_pll_round_rate should return 1.872GHz (297MHz * 5).
There are two problems with the current code of zynqmp_pll_round_rate:
1) When the rate is below PS_PLL_VCO_MIN, it can't find a correct rate
when the parameter "rate" is an integer multiple of *prate, in other words,
if "f" is zero, zynqmp_pll_round_rate won't return a valid frequency which
is from PS_PLL_VCO_MIN to PS_PLL_VCO_MAX. For example, *prate is 33MHz
and the rate is 660MHz, zynqmp_pll_round_rate will not boost up rate and
just return 660MHz, and this will cause clk_calc_new_rates failure since
zynqmp_pll_round_rate returns an invalid rate out of its boundaries.
2) Even if the rate is higher than PS_PLL_VCO_MIN, there is still a risk
that zynqmp_pll_round_rate returns an invalid rate because the function
DIV_ROUND_CLOSEST makes some loss in the fractional part. If the parent
clock *prate is 33333333Hz and we want to set the PLL rate to 1.5GHz,
this function will return 1499999985Hz by using the formula below:
value = *prate * DIV_ROUND_CLOSEST(rate, *prate)).
This value is also invalid since it's slightly smaller than PS_PLL_VCO_MIN.
because DIV_ROUND_CLOSEST makes some loss in the fractional part.
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20220826142030.213805-1-quanyang.wang@windriver.com
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8c1dc9c00 ]
This correction was made in the u-boot SDK recently. There are no
in-tree users of this clock so the impact is minimal.
Fixes: d3d04f6c33 ("clk: Add support for AST2600 SoC")
Link: 8ad54a5ae1
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20220421040426.171256-1-joel@jms.id.au
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 058a3996b8 ]
In ti_find_clock_provider(), of_find_node_by_name() will call
of_node_put() for the 'from' argument, possibly putting the node one too
many times. Let's maintain the of_node_get() from the previous search
and only put when we're exiting the function early. This should avoid a
misbalanced reference count on the node.
Fixes: 51f661ef9a ("clk: ti: Add ti_find_clock_provider() to use clock-output-names")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220915031121.4003589-1-windhl@126.com
[sboyd@kernel.org: Rewrite commit text, maintain reference instead of
get again]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 855ae87a20 ]
No error handling is performed when platform_device_add()
fails. Add error processing before return, and modified
the return value.
Fixes: 77d8f3068c ("clk: imx: scu: add two cells binding support")
Signed-off-by: Lin Yujun <linyujun809@huawei.com>
Link: https://lore.kernel.org/r/20220914033206.98046-1-linyujun809@huawei.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c68cd258a6 ]
The enet_qos_root_clk takes sim_enet_root_clk as parent. When
registering enet_qos_root_clk, it will be put into clk orphan list,
because sim_enet_root_clk is not ready.
When sim_enet_root_clk is ready, clk_core_reparent_orphans_nolock will
set enet_qos_root_clk parent to sim_enet_root_clk.
Because CLK_OPS_PARENT_ENABLE is set, sim_enet_root_clk will be
enabled and disabled during the enet_qos_root_clk reparent phase.
All the above are correct. But with M7 booted early and using
enet, M7 enet feature will be broken, because clk driver probe phase
disable the needed clks, in case M7 firmware not configure
sim_enet_root_clk.
And tune the order would also save cpu cycles.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20220815013428.476015-1-peng.fan@oss.nxp.com
Stable-dep-of: 855ae87a20 ("clk: imx: scu: fix memleak on platform_device_add() fails")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b919a3728 ]
The return value of bcm2835_clock_rate_from_divisor is always unsigned
and also all caller expect this. So fix the declaration accordingly.
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the audio domain clocks")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/20220904141037.38816-1-stefan.wahren@i2se.com
Reviewed-by: Ivan T. Ivanov <iivanov@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c5422851d ]
When testing for a series affecting the VEC, it was discovered that
turning off and on the VEC clock is crashing the system.
It turns out that, when disabling the VEC clock, it's the only child of
the PLLC-per clock which will also get disabled. The source of the crash
is PLLC-per being disabled.
It's likely that some other device might not take a clock reference that
it actually needs, but it's unclear which at this point. Let's make
PLLC-per critical so that we don't have that crash.
Reported-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220926084509.12233-1-maxime@cerno.tech
Reviewed-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Stable-dep-of: 0b919a3728 ("clk: bcm2835: fix bcm2835_clock_rate_from_divisor declaration")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 081a9b7c74 ]
It turns out the internal SATA reference clock signal will stay
unavailable for the SATA interface consumer until the buffer on it's way
is ungated. So aside with having the actual clock divider enabled we need
to ungate a buffer placed on the signal way to the SATA controller (most
likely some rudiment from the initial SoC release). Seeing the switch flag
is placed in the same register as the SATA-ref clock divider at a
non-standard ffset, let's implement it as a separate clock controller with
the set-rate propagation to the parental clock divider wrapper. As such
we'll be able to disable/enable and still change the original clock source
rate.
Fixes: 353afa3a8d ("clk: Add Baikal-T1 CCU Dividers driver")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20220929225402.9696-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2eef31276 ]
Baikal-T1 CCU reference manual says that both xGMAC reference and xGMAC
PTP clocks are generated by two different wrappers with the same constant
divider thus each producing a 156.25 MHz signal. But for some reason both
of these clock sources are gated by a single switch-flag in the CCU
registers space - CCU_SYS_XGMAC_BASE.BIT(0). In order to make the clocks
handled independently we need to define a shared parental gate so the base
clock signal would be switched off only if both of the child-clocks are
disabled.
Note the ID is intentionally set to -2 since we are going to add a one
more internal clock identifier in the next commit.
Fixes: 353afa3a8d ("clk: Add Baikal-T1 CCU Dividers driver")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20220929225402.9696-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c74208868 ]
Most likely due to copy-paste mistake the divider has been set to 10 while
according to the SoC reference manual it's supposed to be 8 thus having
PTP clock frequency of 156.25 MHz.
Fixes: 353afa3a8d ("clk: Add Baikal-T1 CCU Dividers driver")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20220929225402.9696-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c388cc8040 ]
We have discovered random glitches during the system boot up procedure.
The problem investigation led us to the weird outcomes: when none of the
Renesas 5P49V6901 ports are explicitly enabled by the kernel driver, the
glitches disappeared. It was a mystery since the SoC external clock
domains were fed with different 5P49V6901 outputs. The driver code didn't
seem like bogus either. We almost despaired to find out a root cause when
the solution has been found for a more modern revision of the chip. It
turned out the 5P49V6901 clock generator stopped its output for a short
period of time during the VC5_OUT_DIV_CONTROL register writing. The same
problem was found for the 5P49V6965 revision of the chip and was
successfully fixed in commit fc336ae622 ("clk: vc5: fix output disabling
when enabling a FOD") by enabling the "bypass_sync" flag hidden inside
"Unused Factory Reserved Register". Even though the 5P49V6901 registers
description and programming guide doesn't provide any intel regarding that
flag, setting it up anyway in the officially unused register completely
eliminated the denoted glitches. Thus let's activate the functionality
submitted in commit fc336ae622 ("clk: vc5: fix output disabling when
enabling a FOD") for the Renesas 5P49V6901 chip too in order to remove the
ports implicit inter-dependency.
Fixes: dbf6b16f56 ("clk: vc5: Add support for IDT VersaClock 5P49V6901")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Link: https://lore.kernel.org/r/20220929225402.9696-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fef14676fc ]
During the previous |struct clk| to |struct clk_hw| clk provider API
migration in commit 6f691a5862 ("clk: mediatek: Switch to clk_hw
provider APIs"), a few clk_unregister_*() calls were missed.
Migrate the remaining ones to the |struct clk_hw| provider API, i.e.
change clk_unregister_*() to clk_hw_unregister_*().
Fixes: 6f691a5862 ("clk: mediatek: Switch to clk_hw provider APIs")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220926102523.2367530-3-wenst@chromium.org
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20f7a0dba9 ]
When the cleanup paths for the various clk register APIs in the MediaTek
clk library were added, the one in the dividers type used the wrong type
of unregister function. This would result in incorrect dereferencing of
the clk pointer and freeing of invalid pointers.
Fix this by switching to the correct type of clk unregistration call.
Fixes: 3c3ba2ab02 ("clk: mediatek: mtk: Implement error handling in register APIs")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220926102523.2367530-2-wenst@chromium.org
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5f7bf5458 ]
The MFG_BG3D is a gate to enable/disable clock output to the GPU,
but the actual output is decided by multiple muxes; in particular:
mfg_ck_fast_ref muxes between "slow" (top_mfg_core_tmp) and
"fast" (MFGPLL) clock, while top_mfg_core_tmp muxes between the
26MHz clock and various system PLLs.
The clock gate comes after all the muxes, so its parent is
mfg_ck_fast_reg, not top_mfg_core_tmp.
Reparent MFG_BG3D to the latter to match the hardware and add the
CLK_SET_RATE_PARENT flag to it: this way we ensure propagating
rate changes that are requested on MFG_BG3D along its entire clock
tree.
Fixes: 35016f10c0 ("clk: mediatek: Add MT8195 mfgcfg clock support")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220927101128.44758-6-angelogioacchino.delregno@collabora.com
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f94f545f2 ]
The only clock in the MT8183 MFGCFG block feeds the GPU. Propagate its
rate change requests to its parent, so that DVFS for the GPU can work
properly.
Fixes: acddfc2c26 ("clk: mediatek: Add MT8183 clock support")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220927101128.44758-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 068a0605ef ]
The DEFAULT and BRAMMO PLL offsets are non-standard in downstream, but
currently only BRAMMO ones are overridden. Override DEFAULT ones too.
A very similar thing is happening in gcc-qcm2290 driver.
Fixes: cbe63bfdc5 ("clk: qcom: Add Global Clock controller (GCC) driver for SM6115")
Signed-off-by: Adam Skladowski <a_skl39@protonmail.com>
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220830075620.974009-2-iskren.chernev@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86e78995c9 ]
While fixing up the driver I noticed that my IPQ8074 board was hanging
after CPUFreq switched the frequency during boot, WDT would eventually
reset it.
So mark apcs_alias0_core_clk as critical since its the clock feeding the
CPU cluster and must never be disabled.
Fixes: 5e77b4ef1b ("clk: qcom: Add ipq6018 apss clock controller")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220818220628.339366-3-robimarko@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50ee65dc51 ]
While working on the Fxtec Pro1X device, this error shows up with
my own minimal configuration:
gcc-sm6115: probe of 1400000.clock-controller failed with error -38
The clock driver depends on CONFIG_QCOM_GDSC and after enabling
that, the driver probes successfully.
Signed-off-by: Dang Huynh <danct12@riseup.net>
Fixes: cbe63bfdc5 ("clk: qcom: Add Global Clock controller (GCC)
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220910170207.1592220-1-danct12@riseup.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f10f49cd9 ]
The pwrmcu is responsible for power management and idle states in SSPM:
on older SoCs this was managed in Linux drivers like sspm/mcupm/eemgpu
but, at least on MT8195, this functionality was transferred to the ATF
firmware.
For this reason, turning off the pwrmcu related clocks from the kernel
will lead to unability to resume the platform after suspend and other
currently unknown PM related side-effects.
Set the PWRMCU and PWRMCU_BUS_H clocks as critical to prevent the
kernel from turning them off, fixing the aforementioned issue.
Fixes: e2edf59dec ("clk: mediatek: Add MT8195 infrastructure clock support")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220719093316.37253-1-angelogioacchino.delregno@collabora.com
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f24d71feb2 ]
Like it was done for the vdo0_dp_intf0_dp_intf clock (used for eDP),
add the CLK_SET_RATE_PARENT flag to CLK_VDO1_DPINTF (used for DP)
and also fix its parent clock name as it has to be "top_dp" for two
reasons:
- This is its real parent!
- Likewise to eDP/VDO0 counterpart, we need clock source
selection on CLK_TOP_DP.
Fixes: 269987505b ("clk: mediatek: Add MT8195 vdosys1 clock support")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220816193257.658487-3-nfraprado@collabora.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f0dadd230 ]
Add the CLK_SET_RATE_PARENT flag to the CLK_VDO0_DP_INTF0_DP_INTF
clock: this is required to trigger clock source selection on
CLK_TOP_EDP, while avoiding to manage the enablement of the former
separately from the latter in the displayport driver.
Fixes: 70282c90d4 ("clk: mediatek: Add MT8195 vdosys0 clock support")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220816193257.658487-2-nfraprado@collabora.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6956c18f4a ]
In commit 3f905469c8 ("clk: qcom: gcc: Use floor ops for SDCC clocks")
floor ops were applied to SDCC2 only, but flooring is also required on
the SDCC1 apps clock which is used by the eMMC card on Sony's Nile
platform, and otherwise result in the typicial "Card appears
overclocked" warnings observed on many other platforms before:
mmc0: Card appears overclocked; req 52000000 Hz, actual 100000000 Hz
mmc0: Card appears overclocked; req 52000000 Hz, actual 100000000 Hz
mmc0: Card appears overclocked; req 104000000 Hz, actual 192000000 Hz
Fixes: f2a76a2955 ("clk: qcom: Add Global Clock controller (GCC) driver for SDM660")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Tested-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220714203822.186448-1-marijn.suijten@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e343bafe0 ]
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 37c26a9065 ("clk: tegra: add clock support for Tegra20")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220523152811.19692-1-linmq006@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db16a80c76 ]
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 2cb5efefd6 ("clk: tegra: Implement clocks for Tegra114")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220523143834.7587-1-linmq006@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56c78cb1f0 ]
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 6b301a059e ("clk: tegra: Add support for Tegra210 clocks")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220523142608.65074-1-linmq006@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91e6455bf7 ]
We should hold the reference returned by of_get_parent() and use it
to call of_node_put() for refcount balance.
Fixes: f95e8c7923 ("clk: sprd: support to get regmap from parent node")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220704004729.272481-1-windhl@126.com
Reviewed-by: Orson Zhai <orsonzhai@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37c381b812 ]
In berlin2_clock_setup() and berlin2q_clock_setup(), we need to
call of_node_put() for the reference returned by of_get_parent()
which has increased the refcount. We should call *_put() in fail
path or when it is not used anymore.
Fixes: 26b3b6b959 ("clk: berlin: prepare simple-mfd conversion")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220708084900.311684-1-windhl@126.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8ea4273bc ]
In legacy_init_clockgen(), we need to hold the reference returned
by of_get_parent() and use it to call of_node_put() for refcount
balance.
Beside, in create_sysclk(), we need to call of_node_put() on 'sysclk'
also for refcount balance.
Fixes: 0dfc86b317 ("clk: qoriq: Move chip-specific knowledge into driver")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220628143851.171299-1-windhl@126.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d6aa08c54 ]
In oxnas_stdclk_probe(), we need to hold the reference returned by
of_get_parent() and use it to call of_node_put() for refcount
balance.
Fixes: 0bbd72b4c6 ("clk: Add Oxford Semiconductor OXNAS Standard Clocks")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220628143155.170550-1-windhl@126.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 429973306f ]
We should hold the reference returned by of_get_parent() and use it
to call of_node_put() for refcount balance.
Fixes: 3efe64ef51 ("clk: st: clkgen-fsyn: search reg within node or parent")
Fixes: 810251b0d3 ("clk: st: clkgen-mux: search reg within node or parent")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220628142416.169808-1-windhl@126.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89ab396d71 ]
We should hold the reference returned by of_get_parent() and use it
to call of_node_put() for refcount balance.
Fixes: 88e2da8124 ("clk: meson: aoclk: refactor common code into dedicated file")
Fixes: 6682bd4d44 ("clk: meson: factorise meson64 peripheral clock controller drivers")
Fixes: bb6eddd1d2 ("clk: meson: meson8b: use the HHI syscon if available")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220628141038.168383-1-windhl@126.com
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
There is build warning when CONFIG_OF is not selected.
>> drivers/clk/imx/clk-imx93.c:324:34: warning: 'imx93_clk_of_match'
>> defined but not used [-Wunused-const-variable=]
324 | static const struct of_device_id imx93_clk_of_match[] = {
| ^~~~~~~~~~~~~~~~~~
The driver only support DT table, no sense to use of_match_ptr.
Fixes: 24defbe194 ("clk: imx: add i.MX93 clk")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20220830033137.4149542-3-peng.fan@oss.nxp.com
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
After commit 31fd9b79dc ("ARM: dts: BCM5301X: update CRU block
description") a warning from clk-iproc-pll.c was generated due to a
duplicate PLL name as well as the console stopped working. Upon closer
inspection it became clear that iproc_pll_clk_setup() used the Device
Tree node unit name as an unique identifier as well as a parent name to
parent all clocks under the PLL.
BCM5301X was the first platform on which that got noticed because of the
DT node unit name renaming but the same assumptions hold true for any
user of the iproc_pll_clk_setup() function.
The first 'clock-output-names' property is always guaranteed to be
unique as well as providing the actual desired PLL clock name, so we
utilize that to register the PLL and as a parent name of all children
clock.
Fixes: 5fe225c105 ("clk: iproc: add initial common clock support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20220905161504.1526-1-f.fainelli@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In commit 4167ac8a65 ("clk: sunxi-ng: sun50i: h6: Modify GPU clock
configuration to support DFS") divider M0 was forced to be 1 in order to
support DFS. However, that left N as it is, at high value of 36. On
boards without devfreq enabled (all of them in kernel 6.0), this
effectively sets GPU frequency to 864 MHz. This is about 100 MHz above
maximum supported frequency.
In order to fix this, let's set N to 18 (register value 17). That way
default frequency of 432 MHz is preserved.
Fixes: 4167ac8a65 ("clk: sunxi-ng: sun50i: h6: Modify GPU clock configuration to support DFS")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220928200122.3963509-1-jernej.skrabec@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is no dedicate parent clock for QSPI so SET_RATE_PARENT flag
should not be used. For instance, the default parent clock for QSPI is
pll2_bus, which is also the parent clock for quite a few modules, such
as MMDC, once GPMI NAND set clock rate for EDO5 mode can cause system
hang due to pll2_bus rate changed.
Fixes: f1541e15e3 ("clk: imx6sx: Switch to clk_hw based API")
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20220915150959.3646702-1-han.xu@nxp.com
Tested-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It contains fixes for Polarire SoCs:
- fix panic at boot in clock initialization when building with clang-15
- make RTC's AHB clock critical as rtc will stop if the AHB
interface clock is disabled
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTsZ8eserC1pmhwqDmejrg/N2X7/QUCYyLmDgAKCRCejrg/N2X7
/dS5AQD1meKPe/O9SPdiU3bibnVlOiYhi1DrLnLA5G1z/JQoTwD/WPeqm1DSWQ3g
8Z7CNVQJ40wTz9HgD7wt1n1U8guDfQs=
=P4U3
-----END PGP SIGNATURE-----
Merge tag 'clk-microchip-fixes-6.0' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into clk-fixes
Pull Microchip clock fixes for Polarfire SoCs:
- fix panic at boot in clock initialization when building with clang-15
- make RTC's AHB clock critical as rtc will stop if the AHB
interface clock is disabled
* tag 'clk-microchip-fixes-6.0' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
clk: microchip: mpfs: make the rtc's ahb clock critical
clk: microchip: mpfs: fix clk_cfg array bounds violation
The onboard RTC's AHB bus clock must be kept running as the RTC will
stop & lose track of time if the AHB interface clock is disabled.
Fixes: 635e5e7337 ("clk: microchip: Add driver for Microchip PolarFire SoC")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220909123123.2699583-3-conor.dooley@microchip.com
There is an array bounds violation present during clock registration,
triggered by current code by only specific toolchains. This seems to
fail gracefully in v6.0-rc1, using a toolchain build from the riscv-
gnu-toolchain repo and with clang-15, and life carries on. While
converting the driver to use standard clock structs/ops, kernel panics
were seen during boot when built with clang-15:
[ 0.581754] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000b1
[ 0.591520] Oops [#1]
[ 0.594045] Modules linked in:
[ 0.597435] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.0.0-rc1-00011-g8e1459cf4eca #1
[ 0.606188] Hardware name: Microchip PolarFire-SoC Icicle Kit (DT)
[ 0.613012] epc : __clk_register+0x4a6/0x85c
[ 0.617759] ra : __clk_register+0x49e/0x85c
[ 0.622489] epc : ffffffff803faf7c ra : ffffffff803faf74 sp : ffffffc80400b720
[ 0.630466] gp : ffffffff810e93f8 tp : ffffffe77fe60000 t0 : ffffffe77ffb3800
[ 0.638443] t1 : 000000000000000a t2 : ffffffffffffffff s0 : ffffffc80400b7c0
[ 0.646420] s1 : 0000000000000001 a0 : 0000000000000001 a1 : 0000000000000000
[ 0.654396] a2 : 0000000000000001 a3 : 0000000000000000 a4 : 0000000000000000
[ 0.662373] a5 : ffffffff803a5810 a6 : 0000000200000022 a7 : 0000000000000006
[ 0.670350] s2 : ffffffff81099d48 s3 : ffffffff80d6e28e s4 : 0000000000000028
[ 0.678327] s5 : ffffffff810ed3c8 s6 : ffffffff810ed3d0 s7 : ffffffe77ffbc100
[ 0.686304] s8 : ffffffe77ffb1540 s9 : ffffffe77ffb1540 s10: 0000000000000008
[ 0.694281] s11: 0000000000000000 t3 : 00000000000000c6 t4 : 0000000000000007
[ 0.702258] t5 : ffffffff810c78c0 t6 : ffffffe77ff88cd0
[ 0.708125] status: 0000000200000120 badaddr: 00000000000000b1 cause: 000000000000000d
[ 0.716869] [<ffffffff803fb892>] devm_clk_hw_register+0x62/0xaa
[ 0.723420] [<ffffffff80403412>] mpfs_clk_probe+0x1e0/0x244
In v6.0-rc1 and later, this issue is visible without the follow on
patches doing the conversion using toolchains provided by our Yocto
meta layer too.
It fails on "clk_periph_timer" - which uses a different parent, that it
tries to find using the macro:
\#define PARENT_CLK(PARENT) (&mpfs_cfg_clks[CLK_##PARENT].cfg.hw)
If parent is RTCREF, so the macro becomes: &mpfs_cfg_clks[33].cfg.hw
which is well beyond the end of the array. Amazingly, builds with GCC
11.1 see no problem here, booting correctly and hooking the parent up
etc. Builds with clang-15 do not, with the above panic.
Change the macro to use specific offsets depending on the parent rather
than the dt-binding's clock IDs.
Fixes: 1c6a7ea32b ("clk: microchip: mpfs: add RTCREF clock control")
CC: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220909123123.2699583-2-conor.dooley@microchip.com
Access to registers is guarded by ingenic_tcu_{enable,disable}_regs()
so the stop bit can be cleared before accessing a timer channel, but
those functions did not clear the stop bit on SoCs with a global TCU
clock gate.
Testing on the X1000 has revealed that the stop bits must be cleared
_and_ the global TCU clock must be ungated to access timer registers.
This appears to be the norm on Ingenic SoCs, and is specified in the
documentation for the X1000 and numerous JZ47xx SoCs.
If the stop bit isn't cleared, register writes don't take effect and
the system can be left in a broken state, eg. the watchdog timer may
not run.
The bug probably went unnoticed because stop bits are zeroed when
the SoC is reset, and the kernel does not set them unless a timer
gets disabled at runtime. However, it is possible that a bootloader
or a previous kernel (if using kexec) leaves the stop bits set and
we should not rely on them being cleared.
Fixing this is easy: have ingenic_tcu_{enable,disable}_regs() always
clear the stop bit, regardless of the presence of a global TCU gate.
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Paul Cercueil <paul@crapouillou.net>
Fixes: 4f89e4b8f1 ("clk: ingenic: Add driver for the TCU clocks")
Cc: stable@vger.kernel.org
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220617122254.738900-1-aidanmacdonald.0x0@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The clock id limit will be extended in the future, so it would be
helpful to see the actual clock id limit in case the firmware
response has been rejected.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/20220713154953.3336-4-stefan.wahren@i2se.com
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ivan T. Ivanov <iivanov@suse.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
