[ Upstream commit 7e60ab4eb3 ]
[Description]
- Previously we wanted to apply extra 60us of prefetch for min DCFCLK
(200Mhz), but DCFCLK can be calculated to be 201Mhz which underflows
also without the extra prefetch
- Instead, apply the the extra 60us prefetch for any DCFCLK freq <=
300Mhz
Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a31e8b89b ]
[Why]
Calls to dcn20_adjust_freesync_v_startup are no longer
needed as of dcn3+ and can cause underflow in some cases
[How]
Move calls to dcn20_adjust_freesync_v_startup up into
validate_bandwidth for dcn2.x
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 187916e6ed ]
When using cpu to update page tables, vm update fences are unused.
Install stub fence into these fence pointers instead of NULL
to avoid NULL dereference when calling dma_fence_wait() on them.
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Lang Yu <Lang.Yu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66419036f6 ]
An Interrupt Remapping Table (IRT) stores interrupt remapping configuration
for each device. In a normal operation, the AMD IOMMU caches the table
to optimize subsequent data accesses. This requires the IOMMU driver to
invalidate IRT whenever it updates the table. The invalidation process
includes issuing an INVALIDATE_INTERRUPT_TABLE command following by
a COMPLETION_WAIT command.
However, there are cases in which the IRT is updated at a high rate.
For example, for IOMMU AVIC, the IRTE[IsRun] bit is updated on every
vcpu scheduling (i.e. amd_iommu_update_ga()). On system with large
amount of vcpus and VFIO PCI pass-through devices, the invalidation
process could potentially become a performance bottleneck.
Introducing a new kernel boot option:
amd_iommu=irtcachedis
which disables IRTE caching by setting the IRTCachedis bit in each IOMMU
Control register, and bypass the IRT invalidation process.
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Co-developed-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Signed-off-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20230530141137.14376-4-suravee.suthikulpanit@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48aea8b445 ]
Adds the USB and Bluetooth IDs for the Logitech G915 TKL keyboard, for device detection
For this device, this provides battery reporting on top of hid-generic
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Stuart Hayhurst <stuart.a.hayhurst@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7607f12ba7 ]
In the beginning, commit 18eeef46d3 ("HID: i2c-hid: goodix: Tie the
reset line to true state of the regulator") introduced a change to tie
the reset line of the Goodix touchscreen to the state of the regulator
to fix a power leakage issue in suspend.
After some time, the change was deemed unnecessary and was reverted in
commit 557e05fa9f ("HID: i2c-hid: goodix: Stop tying the reset line to
the regulator") due to difficulties in managing regulator notifiers for
designs like Evoker, which provides a second power rail to touchscreen.
However, the revert caused a power regression on another Chromebook
device Steelix in the field, which has a dedicated always-on regulator
for touchscreen and was covered by the workaround in the first commit.
To address both cases, this patch adds the support for the new
"goodix,no-reset-during-suspend" property in the driver:
- When set to true, the driver does not assert the reset GPIO during
power-down.
Instead, the GPIO will be asserted during power-up to ensure the
touchscreen always has a clean start and consistent behavior after
resuming.
This is for designs with a dedicated always-on regulator.
- When set to false or unset, the driver uses the original control flow
and asserts GPIO and disables regulators normally.
This is for the two-regulator and shared-regulator designs.
Signed-off-by: Fei Shao <fshao@chromium.org>
Suggested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Jeff LaBundy <jeff@labundy.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 359ed24a0d ]
We observed that on Chromebook device Steelix, if Goodix GT7375P
touchscreen is powered in suspend (because, for example, it connects to
an always-on regulator) and with the reset GPIO asserted, it will
introduce about 14mW power leakage.
To address that, we add this property to skip reset during suspend.
If it's set, the driver will stop asserting the reset GPIO during
power-down. Refer to the comments in the driver for details.
Signed-off-by: Fei Shao <fshao@chromium.org>
Suggested-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Jeff LaBundy <jeff@labundy.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 314a7ffd7c ]
This commit fixes a memory leak caused when clearing the user_mappings
info when a new context is opened immediately after user_mapping is
captured and a hard reset is performed.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8b9cea584 ]
Currently upon a heartbeat failure, we don't know if the failure
is due to firmware hang or due to a bad PCI link. Hence, we
are reading a PCI config space register with a known value (vendor ID)
so we will know which of the two possibilities caused the heartbeat
failure.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f751b99255 ]
The functionality described in Commit 61bef9e68d ("ASoC: SOF: Intel: hda: enforce exclusion between HDaudio and SoundWire")
does not seem to be properly implemented with two issues that need to
be corrected.
a) The test used is incorrect when DisplayAudio codecs are not supported.
b) Conversely when only Display Audio codecs can be found, we do want
to start the SoundWire links, if any. That will help add the relevant
topologies and machine descriptors, and identify cases where the
SoundWire information in ACPI needs to be modified with a quirk.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20230606222529.57156-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b407460ee9 ]
It is considered good practice to call cpu_relax() in busy loops, see
Documentation/process/volatile-considered-harmful.rst. This can not
only lower CPU power consumption or yield to a hyperthreaded twin
processor, but also allows an architecture to mitigate hardware issues
(e.g. ARM Erratum 754327 for Cortex-A9 prior to r2p0) in the
architecture-specific cpu_relax() implementation.
In addition, cpu_relax() is also a compiler barrier. It is not
immediately obvious that the @op argument "function" will result in an
actual function call (e.g. in case of inlining).
Where a function call is a C sequence point, this is lost on inlining.
Therefore, with agressive enough optimization it might be possible for
the compiler to hoist the:
(val) = op(args);
"load" out of the loop because it doesn't see the value changing. The
addition of cpu_relax() would inhibit this.
As the iopoll helpers lack calls to cpu_relax(), people are sometimes
reluctant to use them, and may fall back to open-coded polling loops
(including cpu_relax() calls) instead.
Fix this by adding calls to cpu_relax() to the iopoll helpers:
- For the non-atomic case, it is sufficient to call cpu_relax() in
case of a zero sleep-between-reads value, as a call to
usleep_range() is a safe barrier otherwise. However, it doesn't
hurt to add the call regardless, for simplicity, and for similarity
with the atomic case below.
- For the atomic case, cpu_relax() must be called regardless of the
sleep-between-reads value, as there is no guarantee all
architecture-specific implementations of udelay() handle this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/45c87bec3397fdd704376807f0eec5cc71be440f.1685692810.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 526a1876fc ]
if (!SOF_RT711_JDSRC(sof_sdw_quirk)) is tested in rt711_sdca_add_codec_
device_props(), and we don't add software node to the device if jack
source is not set. We need to do the same test in
sof_sdw_rt711_sdca_exit(), and avoid removing software node if jack
source is not set.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230602202225.249209-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d14bd943f ]
Fix USB-related warnings in prtrvt, prtvt7, prti6q and prtwd2 device trees
by disabling unused usbphynop1 and usbphynop2 USB PHYs and providing proper
configuration for the over-current detection. This fixes the following
warnings with the current kernel:
usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests
usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests
imx_usb 2184200.usb: No over current polarity defined
By the way, fix over-current detection on usbotg port for prtvt7, prti6q
and prtwd2 boards. Only prtrvt do not have OC on USB OTG port.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2145328515 ]
With RX coalescing, one CQE entry can be used to indicate multiple packets
on the receive queue. This saves processing time and PCI bandwidth over
the CQ.
The MANA Ethernet driver also uses the v2 version of the protocol. It
doesn't use RX coalescing and its behavior is not changed.
Link: https://lore.kernel.org/r/1684045095-31228-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e89f45edb7 ]
We have SOF and generic ACP support enabled for Vangogh platform
on some machines. Since we have same PCI id used for probing,
add check for machine configuration flag to avoid conflict with
newer pci drivers. Such machine flag has been initialized via
dmi match on few Vangogh based machines. If no flag is
specified probe and register older platform device.
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://lore.kernel.org/r/20230530110802.674939-1-venkataprasad.potturu@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2da4b728f9 ]
R-Car H3 ES1.* was only available to an internal development group and
needed a lot of quirks and workarounds. These become a maintenance
burden now, so our development group decided to remove upstream support
for this SoC and prevent booting it. Public users only have ES2 onwards.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f34a2aa4c ]
IPQ5332 has efuse region to determine the various HW quirks. Lets
add the initial support and the individual fuses will be added as they
are required.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230526125305.19626-3-quic_kathirav@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 608f1b0dbd ]
Each time we go through dsp_work() it does a devm_kasprintf() to
allocate memory to hold the part name string. It's not strictly a memory
leak because devm will free it all if the driver is removed. But we keep
allocating more and more memory to hold the same string.
Move the allocation so that it is performed after the version and
secured state information is gathered and handle allocation errors.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/Message-Id: <20230518150250.1121006-2-rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 205b3d02d5 ]
Add check to fix the possible array out of bounds violation by
making speed equal to GEN1_CORE_CLK_FREQ when its value is more
than the size of "pcie_gen_freq" array. This array has size of
four but possible speed (CLS) values are from "0 to 0xF". So,
"speed - 1" values are "-1 to 0xE".
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Link: https://lore.kernel.org/lkml/72b9168b-d4d6-4312-32ea-69358df2f2d0@nvidia.com/
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfe25fea96 ]
We should use RT711_JD2_100K for on board rt711
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230512173305.65399-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 289e1df00e ]
We should use RT711_JD2_100K for on board rt711.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com
Link: https://lore.kernel.org/r/20230512173305.65399-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f38129bb08 ]
This reverts commit 80c6d6804f.
The orignal commit was intended as a workaround to prevent underflow and
flickering when using one normal monitor and the other high refresh rate
monitor (> 120Hz).
This patch is being reverted in favour of a software solution to enable
SubVP+DRR
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31d7c3a4fc ]
The fences associated with mes queue have to be freed
up during amdgpu_ring_fini.
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87c2213e85 ]
The type of size is unsigned int, if size is 0x40000000, there will
be an integer overflow, size will be zero after size *= sizeof(uint32_t),
will cause uninitialized memory to be referenced later.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: hackyzh002 <hackyzh002@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0138250150 ]
The following call trace is observed when removing the amdgpu driver, which
is caused by that BOs allocated for psp are not freed until removing.
[61811.450562] RIP: 0010:amddrm_buddy_fini.cold+0x29/0x47 [amddrm_buddy]
[61811.450577] Call Trace:
[61811.450577] <TASK>
[61811.450579] amdgpu_vram_mgr_fini+0x135/0x1c0 [amdgpu]
[61811.450728] amdgpu_ttm_fini+0x207/0x290 [amdgpu]
[61811.450870] amdgpu_bo_fini+0x27/0xa0 [amdgpu]
[61811.451012] gmc_v9_0_sw_fini+0x4a/0x60 [amdgpu]
[61811.451166] amdgpu_device_fini_sw+0x117/0x520 [amdgpu]
[61811.451306] amdgpu_driver_release_kms+0x16/0x30 [amdgpu]
[61811.451447] devm_drm_dev_init_release+0x4d/0x80 [drm]
[61811.451466] devm_action_release+0x15/0x20
[61811.451469] release_nodes+0x40/0xb0
[61811.451471] devres_release_all+0x9b/0xd0
[61811.451473] __device_release_driver+0x1bb/0x2a0
[61811.451476] driver_detach+0xf3/0x140
[61811.451479] bus_remove_driver+0x6c/0xf0
[61811.451481] driver_unregister+0x31/0x60
[61811.451483] pci_unregister_driver+0x40/0x90
[61811.451486] amdgpu_exit+0x15/0x447 [amdgpu]
For smu v13_0_2, if the GPU supports xgmi, refer to
commit f5c7e77970 ("drm/amdgpu: Adjust removal control flow for smu v13_0_2"),
it will run gpu recover in AMDGPU_RESET_FOR_DEVICE_REMOVE mode when removing,
which makes all devices in hive list have hw reset but no resume except the
basic ip blocks, then other ip blocks will not call .hw_fini according to
ip_block.status.hw.
Since psp_free_shared_bufs just includes some software operations, so move
it to psp_sw_fini.
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Longlong Yao <Longlong.Yao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96c7c2f4d5 ]
It already happend a few times that patches slipped through which
implemented access to an entity through a job that was already removed
from the entities queue. Since jobs and entities might have different
lifecycles, this can potentially cause UAF bugs.
In order to make it obvious that a jobs entity pointer shouldn't be
accessed after drm_sched_entity_pop_job() was called successfully, set
the jobs entity pointer to NULL once the job is removed from the entity
queue.
Moreover, debugging a potential NULL pointer dereference is way easier
than potentially corrupted memory through a UAF.
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://lore.kernel.org/r/20230418100453.4433-1-dakr@redhat.com
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 128c1ca030 ]
[Why&How]
- Implement interface to program DTBCLK DTO’s
according to reference DTBCLK returned by PMFW
- This is required because DTO programming
requires exact DTBCLK reference freq or it could
result in underflow
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e58f30246c ]
In commit 7beecaf7d5 ("net: phy: at803x: improve the WOL feature"), it
seems not correct to use a wol_en bit in a 1588 Control Register which is
only available on AR8031/AR8033(share the same phy_id) to determine if WoL
is enabled. Change it back to use AT803X_INTR_ENABLE_WOL for determining
the WoL status which is applicable on all chips supporting wol. Also update
the at803x_set_wol() function to only update the 1588 register on chips
having it. After this change, disabling wol at probe from commit
d7cd5e06c9 ("net: phy: at803x: disable WOL at probe") is no longer
needed. Change it to just disable the WoL bit in 1588 register for
AR8031/AR8033 to be aligned with AT803X_INTR_ENABLE_WOL in probe.
Fixes: 7beecaf7d5 ("net: phy: at803x: improve the WOL feature")
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Viorel Suman <viorel.suman@nxp.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 988e8d90b3 ]
Use devm_regulator_get_enable_optional() instead of hand writing it. It
saves some line of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: e58f30246c ("net: phy: at803x: fix the wol setting functions")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6ccbd7fd47 upstream.
EXPORT_SYMBOL and __init is a bad combination because the .init.text
section is freed up after the initialization.
Commit c5a130325f ("ACPI/APEI: Add parameter check before error
injection") exported page_is_ram(), hence the __init annotation should
be removed.
This fixes the modpost warning in ARCH=alpha builds:
WARNING: modpost: vmlinux: page_is_ram: EXPORT_SYMBOL used for init symbol. Remove __init or EXPORT_SYMBOL.
Fixes: c5a130325f ("ACPI/APEI: Add parameter check before error injection")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cd0302be5 upstream.
The ACPI device CSC3556 is a Cirrus Logic CS35L56 mono amplifier which
is used in multiples, and can be connected either to I2C or SPI.
There will be multiple instances under the same Device() node. Add it
to ignore_serial_bus_ids and handle it in the serial-multi-instantiate
driver.
There can be a 5th I2cSerialBusV2, but this is an alias address and doesn't
represent a real device. Ignore this by having a dummy 5th entry in the
serial-multi-instantiate instance list with the name of a non-existent
driver, on the same pattern as done for bsg2150.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20230728111345.7224-1-rf@opensource.cirrus.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 676b7c5eca upstream.
The current code assumes that the CSC3551(multiple cs35l41) always have
its interrupt pin connected to GPIO thus the IRQ can be acquired with
acpi_dev_gpio_irq_get. However on some newer laptop models this is no
longer the case as they have the CSC3551's interrupt pin connected to
APIC. This causes smi_i2c_probe to fail on these machines.
To support these machines, a new macro IRQ_RESOURCE_AUTO was introduced
for cs35l41 smi_node, and smi_get_irq function was modified so it tries
to get GPIO irq resource first and if failed, tries to get
APIC irq resource for cs35l41.
This patch affects only the cs35l41's probing and brings no negative
influence on machines that indeed have the cs35l41's interrupt pin
connected to GPIO.
Signed-off-by: David Xu <xuwd1@hotmail.com>
Link: https://lore.kernel.org/r/SY4P282MB18350CD8288687B87FFD2243E037A@SY4P282MB1835.AUSP282.PROD.OUTLOOK.COM
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e3938cff0 upstream.
Fix exit flow order: call mlxplat_post_exit() after
mlxplat_i2c_main_exit() in order to unregister main i2c driver before
to "mlxplat" driver.
Fixes: 0170f616f4 ("platform: mellanox: Split initialization procedure")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Michael Shych <michaelsh@nvidia.com>
Link: https://lore.kernel.org/r/20230813083735.39090-2-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f8ccdb508 upstream.
Use kernel_power_off() instead of kernel_halt() to pass through
machine_power_off() -> pm_power_off(), otherwise axillary power does
not go off.
Change "power down" bitmask.
Fixes: dd635e33b5 ("platform: mellanox: Introduce support of new Nvidia L1 switch")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Michael Shych <michaelsh@nvidia.com>
Link: https://lore.kernel.org/r/20230813083735.39090-4-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c91d7e8c6 upstream.
Change polarity of chassis health and power signals and fix latch reset
mask for L1 switch.
Fixes: dd635e33b5 ("platform: mellanox: Introduce support of new Nvidia L1 switch")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Michael Shych <michaelsh@nvidia.com>
Link: https://lore.kernel.org/r/20230813083735.39090-3-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d66a8aab7d upstream.
Move debug register offsets to different location due to hardware changes.
Fixes: dd635e33b5 ("platform: mellanox: Introduce support of new Nvidia L1 switch")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Michael Shych <michaelsh@nvidia.com>
Link: https://lore.kernel.org/r/20230813083735.39090-5-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b6aa6610d upstream.
The lenovo-ymc driver is causing the keyboard + touchpad to stop working
on some regular laptop models such as the Lenovo ThinkBook 13s G2 ITL 20V9.
The problem is that there are YMC WMI GUID methods in the ACPI tables
of these laptops, despite them not being Yogas and lenovo-ymc loading
causes libinput to see a SW_TABLET_MODE switch with state 1.
This in turn causes libinput to ignore events from the builtin keyboard
and touchpad, since it filters those out for a Yoga in tablet mode.
Similar issues with false-positive SW_TABLET_MODE=1 reporting have
been seen with the intel-hid driver.
Copy the intel-hid driver approach to fix this and only bind to the WMI
device on machines where the DMI chassis-type indicates the machine
is a convertible.
Add a 'force' module parameter to allow overriding the chassis-type check
so that users can easily test if the YMC interface works on models which
report an unexpected chassis-type.
Fixes: e82882cdd2 ("platform/x86: Add driver for Yoga Tablet Mode switch")
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2229373
Cc: André Apitzsch <git@apitzsch.eu>
Cc: stable@vger.kernel.org
Tested-by: Andrew Kallmeyer <kallmeyeras@gmail.com>
Tested-by: Gergő Köteles <soyer@irl.hu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230812144818.383230-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a66d59b5f upstream.
The msi-ec driver fails to build for me (gcc 7.5):
CC [M] drivers/platform/x86/msi-ec.o
drivers/platform/x86/msi-ec.c:72:6: error: initializer element is not constant
{ SM_ECO_NAME, 0xc2 },
^~~~~~~~~~~
drivers/platform/x86/msi-ec.c:72:6: note: (near initialization for ‘CONF0.shift_mode.modes[0].name’)
drivers/platform/x86/msi-ec.c:73:6: error: initializer element is not constant
{ SM_COMFORT_NAME, 0xc1 },
^~~~~~~~~~~~~~~
drivers/platform/x86/msi-ec.c:73:6: note: (near initialization for ‘CONF0.shift_mode.modes[1].name’)
drivers/platform/x86/msi-ec.c:74:6: error: initializer element is not constant
{ SM_SPORT_NAME, 0xc0 },
^~~~~~~~~~~~~
drivers/platform/x86/msi-ec.c:74:6: note: (near initialization for ‘CONF0.shift_mode.modes[2].name’)
(...)
Don't try to be smart, just use defines for the constant strings. The
compiler will recognize it's the same string and will store it only
once in the data section anyway.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 392cacf2aa ("platform/x86: Add new msi-ec driver")
Cc: stable@vger.kernel.org
Cc: Nikita Kravets <teackot@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Gross <markgross@kernel.org>
Link: https://lore.kernel.org/r/20230805101010.54d49e91@endymion.delvare
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef222f551e upstream.
While performing certain power-off sequences, PCI drivers are called to
suspend and resume their underlying devices through PCI PM (power
management) interface. However the hardware does not support PCI PM
suspend/resume operations so system wide suspend/resume leads to bad MFW
(management firmware) state which causes various follow-up errors in driver
when communicating with the device/firmware.
To fix this driver implements PCI PM suspend handler to indicate
unsupported operation to the PCI subsystem explicitly, thus avoiding system
to go into suspended/standby mode.
Fixes: 61d8658b4a ("scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.")
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230807093725.46829-1-njavali@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1516ee035d upstream.
While performing certain power-off sequences, PCI drivers are called to
suspend and resume their underlying devices through PCI PM (power
management) interface. However the hardware does not support PCI PM
suspend/resume operations so system wide suspend/resume leads to bad MFW
(management firmware) state which causes various follow-up errors in driver
when communicating with the device/firmware.
To fix this driver implements PCI PM suspend handler to indicate
unsupported operation to the PCI subsystem explicitly, thus avoiding system
to go into suspended/standby mode.
Fixes: ace7f46ba5 ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230807093725.46829-2-njavali@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a43b07a87 upstream.
fnic_clean_pending_aborts() was returning a non-zero value irrespective of
failure or success. This caused the caller of this function to assume that
the device reset had failed, even though it would succeed in most cases. As
a consequence, a successful device reset would escalate to host reset.
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com>
Tested-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Link: https://lore.kernel.org/r/20230727193919.2519-1-kartilak@cisco.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>