Currently there is a request_mem_region(r->start, ..
followed by r->start += pdata->regs_offset;
And then in remove
r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
release_mem_region(r->start, resource_size(r));
Here the offset addition is not taken care. Fix the code for the
same.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Due to module.h cleanup it is not anymore included implicitly. Drivers
who want to use it need to include it explicitly.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add #include <linux/module.h> to spi-tegra.c to fix a compilation error
after the removal of module.h from device.h (in patch: "include: replace
linux/module.h with "struct module" wherever possible").
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We found that adding load, Rx data sometimes drops.(with DMA transfer mode)
The cause is that before starting Rx-DMA processing, Tx-DMA processing starts.
This causes FIFO overrun occurs.
This patch fixes the issue by modifying FIFO tx-threshold and DMA descriptor
size like below.
Current this patch
Rx-descriptor 4Byte+12Byte*341 --> 12Byte*340-4Byte-12Byte
Rx-threshold (Not modified)
Tx-descriptor 4Byte+12Byte*341 --> 16Byte-12Byte*340
Rx-threshold 12Byte --> 2Byte
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add recovery processing in case FIFO overrun error occurs with DMA transfer mode.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We found Rx data sometimes drops.(with non-DMA transfer mode)
The cause is read complete condition is not true.
This patch fixes the issue.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
During processing 1 command/data series,
SSN should keep LOW.
However, currently, SSN becomes HIGH.
This patch fixes the issue.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently, in case of reading date from SPI flash,
command is sent twice.
The cause is that tx-memory clear processing is missing .
This patch adds the tx-momory clear processing.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
If CPM mode is not used, the fsl_dummy_rx variable is never allocated. When
the cleanup attempts to free it, the reference count is zero and a WARN is
generated. The same CPM mode check used in the initialize is applied to the
free as well.
Tested on 2.6.33 with the previous spi_mpc8xxx driver. The renamed
spi-fsl-spi driver looks to have the same problem.
Signed-off-by: Jeff Harris <jeff_harris@kentrox.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch fixes a build error, introduced by commit (67fc8b9f, "PM: add
runtime PM support to core Primecell driver") which unfortunately was a little
bit incomplete and did contain a typo (11 instead of 22).
I'm not sure how this patch could have been tested back then, if it
doesn't even compile ;)
The build failure was:
drivers/spi/spi-pl022.c:2292: error: 'adev' undeclared (first use in
this function)
drivers/spi/spi-pl022.c:2344: error: 'pl022_suspend' undeclared here
(not in a function)
The build failure appears e.g. for the u8500 and realview defconfig.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add runtime PM support to the core Primecell driver, following the PCI
model of how this is done.
Rather than having every driver fiddle about with enabling runtime PM,
that's dealt with in the core and instead, drivers just do a put() in
their probe and a balancing get() in their remove function to activate
runtime PM for the device.
As we're dealing with enabling runtime PM in the core, fix up spi-pl022
as it must not enable and disable runtime PM itself anymore.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The dw_{read,write}[lw] macros produce sparse warnings everytime they
are used. The "read" ones cause:
warning: cast removes address space of expression
warning: incorrect type in argument 1 (different address spaces)
expected void const volatile [noderef] <asn:2>*addr
got unsigned int *<noident>
And the "write" ones:
warning: cast removes address space of expression
warning: incorrect type in argument 2 (different address spaces)
expected void volatile [noderef] <asn:2>*addr
got unsigned int *<noident>
Fix this by removing struct dw_spi_reg and converting all the register
offsets to #defines. Then convert the macros into inlined functions so
that proper type checking can occur.
While here, also fix the three sparse warnings in spi-dw-mid.c due to
the return value of ioremap_nocache being stored in a u32 * not a
void __iomem *.
With these changes the spi-dw* files all build with no sparse warnings.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
pl022_dma_remove() should be called only if enable_dma is true. There is no
point calling it when pl022_dma_probe() is not called, which again depends on
enable_dma.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There were few issues with calculate_effective_freq() routine:
- It was returning first rate found >= requested rate. Now, if system have spi's
rate as 83 MHz, with possible prescaled rates as 83, 41.5, 20.75, 13.83 (as we
can prescale with multiples of 2). If user has given rate to be programmed as
22 MHz, then driver programmes it to 41.5 MHz. This looks to be incorrect, as
user might have given the upper limit of the device, and we are programming it
above it.
- Driver finds the first satisfying rate and programmes it, but with other
values of scr & cpsdvsr, it is possible to get more closer rate.
This patch fixes these two issues, with some reformatting inside the code. This
also creates a inline routine to calculate prescaled rate based on spi's rate,
cpsdvsr and scr.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In routine configure_dma(), if transfer->len = PAGE_SIZE, then pages is one more
than required. While leads to one more sg getting allocated.
This is wrong. Correct this to allocate correct number of sg.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
tasklets don't allow invocation to sleeping routines. In configure_dma()
routine, sg_alloc_table() was called with GFP_KERNEL flag and so this causes
crash when called from tasklet.
Replace GFP_KERNEL with GFP_ATOMIC to get this fixed.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There were few formatting related issues in code. This patch fixes them.
Fixes include:
- Remove extra blank lines
- align code to 80 cols
- combine several lines to one line
- Replace multiple spaces with tabs
- Remove spaces before labels
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 22a85e4cd5 (spi/imx: add device tree probe support) broke spi-imx usage
when the SPI chipselect is the one internal to the controller.
On a mx31pdk board the following error is seen:
Registering mxc_nand as whole device
------------[ cut here ]------------
WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x4c/0xf4()
autorequest GPIO-0
Modules linked in:
[<c0014410>] (unwind_backtrace+0x0/0xf4) from [<c0025754>] (warn_slowpath_common+0x4c/0x64)
[<c0025754>] (warn_slowpath_common+0x4c/0x64) from [<c0025800>] (warn_slowpath_fmt+0x30/0x40)
[<c0025800>] (warn_slowpath_fmt+0x30/0x40) from [<c0198688>] (gpio_ensure_requested+0x4c/0xf4)
[<c0198688>] (gpio_ensure_requested+0x4c/0xf4) from [<c01988c8>] (gpio_direction_output+0xa0/0x138)
[<c01988c8>] (gpio_direction_output+0xa0/0x138) from [<c01ed198>] (spi_imx_setup+0x38/0x4c)
[<c01ed198>] (spi_imx_setup+0x38/0x4c) from [<c01eb5d0>] (spi_setup+0x38/0x50)
[<c01eb5d0>] (spi_setup+0x38/0x50) from [<c01eb85c>] (spi_add_device+0x94/0x124)
[<c01eb85c>] (spi_add_device+0x94/0x124) from [<c01eb960>] (spi_new_device+0x74/0xac)
[<c01eb960>] (spi_new_device+0x74/0xac) from [<c01eb9b8>] (spi_match_master_to_boardinfo+0x20/0x40)
[<c01eb9b8>] (spi_match_master_to_boardinfo+0x20/0x40) from [<c01eba88>] (spi_register_master+0xb0/0x104)
[<c01eba88>] (spi_register_master+0xb0/0x104) from [<c01ec0b4>] (spi_bitbang_start+0x104/0x17c)
[<c01ec0b4>] (spi_bitbang_start+0x104/0x17c) from [<c02c2c4c>] (spi_imx_probe+0x2fc/0x404)
[<c02c2c4c>] (spi_imx_probe+0x2fc/0x404) from [<c01c2498>] (platform_drv_probe+0x18/0x1c)
[<c01c2498>] (platform_drv_probe+0x18/0x1c) from [<c01c1058>] (driver_probe_device+0x78/0x174)
[<c01c1058>] (driver_probe_device+0x78/0x174) from [<c01c11e0>] (__driver_attach+0x8c/0x90)
[<c01c11e0>] (__driver_attach+0x8c/0x90) from [<c01c0860>] (bus_for_each_dev+0x60/0x8c)
[<c01c0860>] (bus_for_each_dev+0x60/0x8c) from [<c01c0088>] (bus_add_driver+0xa0/0x288)
[<c01c0088>] (bus_add_driver+0xa0/0x288) from [<c01c179c>] (driver_register+0x78/0x18c)
[<c01c179c>] (driver_register+0x78/0x18c) from [<c0008490>] (do_one_initcall+0x34/0x178)
[<c0008490>] (do_one_initcall+0x34/0x178) from [<c03a5204>] (kernel_init+0x74/0x118)
[<c03a5204>] (kernel_init+0x74/0x118) from [<c000f65c>] (kernel_thread_exit+0x0/0x8)
---[ end trace 759f924b30fd5a44 ]---
Fix this issue by using the original chip select logic and make spi-imx to work again.
Tested on a mx31pdk that uses the hardware SPI chipselect pins and also
on a mx27pdk that uses GPIO as SPI chipselect.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch modifies to merge the dma control code. Original
s3c64xx spi driver has each dma control code for rx and tx
channel. This patch merges these dma control codes into one.
With this patch, a dma setup function and callback function
handle for both rx and tx channel.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds to support DMA generic API to transfer raw
SPI data. Basiclly the spi driver uses DMA generic API if
architecture supports it. Otherwise, uses Samsung specific
S3C-PL330 APIs.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The remove function in the PL022 driver cannot abort the remove
function any way, so restructure the code so as not to make that
assumption. Remove will now proceed no matter whether it can
stop the transfer queue or not.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
spi/imx: add device tree probe support
spi/imx: copy gpio number passed by platform data into driver private data
spi/imx: use soc name in spi device type naming scheme
spi/imx: merge type SPI_IMX_VER_0_7 into SPI_IMX_VER_0_4
spi/imx: do not use spi_imx2_3 to name SPI_IMX_VER_2_3 function and macro
spi/imx: use mx21 to name SPI_IMX_VER_0_0 function and macro
spi/imx: do not make copy of spi_imx_devtype_data
spi/dw: Add spi number into spi irq desc
spi/tegra: Use engineering names in DT compatible property
spi/fsl_spi: fix CPM spi driver
mach-s3c2410: remove unused spi-gpio.h file
spi: remove obsolete spi-s3c24xx-gpio driver
mach-gta2: remove unused spi-gpio.h include
mach-qt2410: convert to spi_gpio
mach-jive: convert to spi_gpio
spi/pxa2xx: Remove unavailable ssp_type from documentation
spi/bfin_spi: uninline fat queue funcs
spi/bfin_spi: constify pin array
spi/bfin_spi: use structs for accessing hardware regs
spi/topcliff-pch: Support new device ML7223 IOH
...
Fix up trivial conflict in arch/arm/mach-ep93xx/Makefile
It adds device tree probe support for spi-imx driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It copies gpio number passed via platform data embedded pointer into
driver private data, so that we do not need to refer to this embedded
pointer passed by platform data after probe function exits.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Software defined version number is not stable enough to be used
in device type naming scheme. The patch changes it to use implicit
soc name for spi device type definition. In this way, we can easily
align the naming scheme with device tree binding, which comes later.
It removes fifosize from spi_imx_data and adds devtype there, so that
fifosize can be set in an inline function according to devtype.
Also, cpu_is_mx can be replaced by inline functions checking devtype.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The only difference between SPI_IMX_VER_0_7 and SPI_IMX_VER_0_4 is
.config function. The patch uses cpu_is_mx35 (to be removed) as the
temporary solution to consolidate functions spi_imx0_4_config and
spi_imx0_7_config into mx31_config. As a result, type SPI_IMX_VER_0_7
can be merged into SPI_IMX_VER_0_4.
It also renames function spi_imx0_4_reset to mx31_reset to keep
consistency with other function naming.
A couple of redundant macros, MX3_CSPISTAT and MX3_CSPISTAT_RR,
together with the useless type SPI_IMX_VER_0_5 also get cleaned up.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It's confusing to use spi_imx2_3 to name SPI_IMX_VER_2_3 function
and macro, as it easily make people think of imx2 and imx3. It's
better to use specific soc name just like what other SPI_IMX_VER
do. For SPI_IMX_VER_2_3 case, it will be mx51. To distinguish it
from CSPI on mx51, mx51_ecspi might be a good choice.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
SPI_IMX_VER_0_0 covers i.mx21 and i.mx27. It makes more sense to
use mx21 rather than mx27 to name SPI_IMX_VER_0_0 function and
macro, since i.mx21 comes out ealier than i.mx27.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
spi_imx_devtype_data has already been driver private data. There is
really no need to make a copy in spi_imx_data. Instead, a reference
pointer works perfectly fine.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The existing macro fails for following scenarios.
1) S5P64X0 channel 1
2) S5PV210 channel 1
The FIFO data level supported in the above SoCs either 64 or
256 bytes depending on the channel. Because of this the TX_DONE
is the 25 bit in the status register.
The existing macro works for the following scenarios
1) S3C6410 all channels
2) S5PC100 all channels
The FIFO data level supported in the above SoCs 64 bytes
on all the channels. Because of this the TX_DONE is the 21 bit
in the status register.
So when we use the existing macro for the non-working SoCs
it is not anding with the TX_DONE bit for transmission status check.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Engineering names are more stable than marketing names. Hence, use them
for Device Tree compatible properties instead.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch fixes the freescale spi driver for CPM. Without this
patch SPI on CPM failed because cpm_muram_alloc_fixed tries to
allocate muram in an preserved area. The error reported was:
mpc8xxx_spi f0011a80.spi: can't allocate spi parameter ram
mpc8xxx_spi: probe of f0011a80.spi failed with error -12
Now the driver uses of_iomap to get access to this area
similar to i2c driver driver in the i2c-cpm.c which has a
similar device tree node. This is tested on a MPC8247 with CPM2.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It was equivalent to spi-gpio, and there's no longer any in-tree users
of it, so get rid of it.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There's no need for these queue funcs to be inlined, so drop the
markings. This shaves off a few hundred duplicated bytes.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This array isn't written anywhere, so constify it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Rather than hardcoding the register sizes/offsets in this file, use the
existing struct in the spi header for reading/writing the hardware.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The default bits per word setting should be 8 bits, but since most of our
devices have been explicitly setting this up, we didn't notice when the
default stopped working.
At the moment, any default transfers without an explicit bit size setting
error out with:
bfin-spi bfin-spi.0: transfer: unsupported bits_per_word
So in the transfer logic, have a bits_per_word setting of 0 fall into the
8 bit transfer logic.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The platform configuration can select custom FIFO watermarks, but
these may conflict the actual FIFO size of the PL022 variant if
set too high. So strengthen the sanity checks to deny any
conflicting settings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Insert notifiers for the runtime PM API. With this the runtime
PM layer kicks in to action where used.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Rebased to Linux 3.0-rc3, edit description]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Configure the DMA burstsize from the FIFO trigger level supplied
with the controller configuration data. This is based on a patch
from Virupax, but I rewrote it differently.
Reported-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Return error on out of range cpsdvsr value.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch enables this SPI driver works with DMA mode.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Support ML7213 device of OKI SEMICONDUCTOR.
ML7213 is companion chip of Intel Atom E6xx series for IVI(In-Vehicle Infotainment).
ML7213 is compatible for Intel EG20T PCH.
v4: - Delete unrelated whitespace
- Prevent device driver from accessing platform data
- Add __devinit and __devexit
- Save pdev->dev to pd_dev->dev.parent
- Have own suspend/resume processing in platform_driver.
- Care returned value in pch_spi_init
- Change unregister order
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds DMA support for the EP93xx SPI driver. By default the DMA is
not enabled but it can be enabled by setting ep93xx_spi_info.use_dma to true
in board configuration file.
Note that the SPI driver still uses PIO for small transfers (<= 8 bytes) for
performance reasons.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Sort the SPI makefile and enforce the naming convention spi_*.c for
spi drivers.
This change also rolls the contents of atmel_spi.h into the .c file
since there is only one user of that particular include file.
v2: - Use 'spi-' prefix instead of 'spi_' to match what seems to be
be the predominant pattern for subsystem prefixes.
- Clean up filenames in Kconfig and header comment blocks
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
SPI protocol drivers can submit messages specifying needed bits_per_word
parameter for a message transfer. The bitbang driver currently ignores
bits_per_word given by a singe message and always uses master's
bits_per_word parameter. Only use master's bits_per_word when a
message didn't specify needed bits_per_word for ongoing transfer.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
fixes below compilation warning. The variable doesn't actual ever get
used uninitialized, but that's no reason to be sloppy.
drivers/spi/omap2_mcspi.c: In function 'omap2_mcspi_txrx_dma':
drivers/spi/omap2_mcspi.c:301: warning: 'elements' may be used uninitialized in this function
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
[grant.likely: amended description]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The Blackfin SPORT peripheral is a pretty flexible device. With enough
coaching, we can make it generate SPI compatible waveforms. This is
desirable as the SPORT can run at much higher clock frequencies than the
dedicated on-chip SPI peripheral, and it can do full duplex DMA. It also
opens up the possibility of multiple SPI buses in case someone wants to
dedicate a whole bus to a specific part that does not play well with
others.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch includes below fixes:
1. Add missing device_remove_file for dev_attr_status_show in tle62x0_remove.
2. Fix tle62x0_probe error handling:
Currently, if the error happens when ptr > 0, gpio_attrs[0] is not
properly remove.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (57 commits)
regulator: Fix 88pm8607.c printk format warning
input: Add support for Qualcomm PMIC8XXX power key
input: Add Qualcomm pm8xxx keypad controller driver
mfd: Add omap-usbhs runtime PM support
mfd: Fix ASIC3 SD Host Controller Configuration size
mfd: Fix omap_usbhs_alloc_children error handling
mfd: Fix omap usbhs crash when rmmoding ehci or ohci
mfd: Add ASIC3 LED support
leds: Add ASIC3 LED support
mfd: Update twl4030-code maintainer e-mail address
mfd: Correct the name and bitmask for ab8500-gpadc BTempPullUp
mfd: Add manual ab8500-gpadc batt temp activation for AB8500 3.0
mfd: Provide ab8500-core enumerators for chip cuts
mfd: Check twl4030-power remove script error condition after i2cwrite
mfd: Fix twl6030 irq definitions
mfd: Add phoenix lite (twl6025) support to twl6030
mfd: Avoid to use constraint name in 88pm860x regulator driver
mfd: Remove checking on max8925 regulator[0]
mfd: Remove unused parameter from 88pm860x API
mfd: Avoid to allocate 88pm860x static platform data
...
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6:
spi/amba-pl022: work in polling or interrupt mode if pl022_dma_probe fails
spi/spi_s3c24xx: Use spi_bitbang_stop instead of spi_unregister_master in s3c24xx_spi_remove
spi/spi_nuc900: Use spi_bitbang_stop instead of spi_unregister_master in nuc900_spi_remove
spi/spi_tegra: use spi_unregister_master() instead of spi_master_put()
spi/spi_sh: use spi_unregister_master instead of spi_master_put in remove path
spi: Use void pointers for data in simple SPI I/O operations
spi/pl022: use cpu_relax in the busy loop
spi/pl022: mark driver non-experimental
spi/pl022: timeout on polled transfer v2
spi/dw_spi: improve the interrupt mode with the batch ops
spi/dw_spi: change poll mode transfer from byte ops to batch ops
spi/dw_spi: remove the un-necessary flush()
spi/dw_spi: unify the low level read/write routines
With the addition of a device platform mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If pl022_dma_probe fails, we can try to transfer data in polling or interrupt
mode. Also, set platform_info->enable_dma to 0, so that no other code tries to
use dma.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Calling spi_bitbang_stop() will also destroy bitbang->workqueue,
which is created by calling spi_bitbang_start() in s3c24xx_spi_probe().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Calling spi_bitbang_stop() will also destroy bitbang->workqueue,
which is created by calling spi_bitbang_start() in nuc900_spi_probe().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
spi_master_put() should only be used in error handling.
Once spi_register_master() returns success, we should call
spi_unregister_master() instead.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
spi_master_put() should only be used in error handling.
Once spi_register_master() returns success, we should call
spi_unregister_master() instead.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently the simple SPI I/O operations all take pointers to u8 * buffers
to operate on. This creates needless type compatibility issues and the
underlying spi_transfer structure uses void pointers anyway so convert the
API over to take void pointers too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This relaxes the cpu in the polling busy-wait loop.
Reported-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This driver has no TODO, and is now used on several platforms:
ARM, U300, Ux500, SPEAr and more. So drop the EXPERIMENTAL
requirement.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds the missing handling of polling timeouts and deletes
our last todo.
Signed-off-by: Magnus Templing <magnus.templing@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Fixups from review by Wolfram Sang]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'spi/merge' of git://git.secretlab.ca/git/linux-2.6:
dt/fsldma: fix build warning caused by of_platform_device changes
spi: Fix race condition in stop_queue()
gpio/pch_gpio: Fix output value of pch_gpio_direction_output()
gpio/ml_ioh_gpio: Fix output value of ioh_gpio_direction_output()
gpio/pca953x: fix error handling path in probe() call
There's a race condition in stop_queue() in some drivers -
if drv_data->queue is empty, but drv_data->busy is still set
(or opposite situation) stop_queue will return -EBUSY.
So fix loop condition to check that both drv_data->queue is empty
and drv_data->busy is not set.
This patch affects following drivers:
pxa2xx_spi
spi_bfin5xx
amba-pl022
dw_spi
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
leverage the performance gain by change in low level
read/write batch operations
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Current poll transfer will read/write one word, then wait till the
hw is non-busy, it's not efficient. This patch will try to read/write
as many words as permitted by hardware FIFO depth.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The flush() is used to drain all the left data in rx fifo, currently
is is always called together with disabling hw. But from spec, disabling
hw will also reset all the fifo, so flush() is not needed.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The original version has many duplicated codes for null/u8/u16 case,
so unify them to make it cleaner
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
spi/pl022: Add loopback support for the SPI on 5500
spi/omap_mcspi: Fix broken last word xfer
of/flattree: minor cleanups
dt: eliminate OF_NO_DEEP_PROBE and test for NULL match table
dt: protect against NULL matches passed to of_match_node()
dt: Refactor of_platform_bus_probe()
Extend the vendor data with a loopback field, and add new
amba-pl022 vendor data for the DB5500 pl023, as the pl023
on db8500 and db5500 vary.
Signed-off-by: Prajadevi H <prajadevi.h@stericsson.com>
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Commit adef658 "spi/omap_mcspi: catch xfers of non-multiple SPI word size"
broke the transmission of last word in cases where access is multiple of
word size and word size is 16 or 32 bits.
Fix this by replacing the test "c > (word_len>>3)" in do-while loops with
"c >= 'pointer increment size'". This ensures that the last word is
transmitted in above case and still allow to break the loop and prevent
variable c underflow in cases where word size != 'pointer increment size'.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Tested-by: Sourav Poddar<sourav.poddar@ti.com>
Acked-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Note that the mfd's platform_data is marked __devinitdata. This
is still correct in all cases except for the timbgpio driver, whose
remove hook has been changed to no longer reference the pdata.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
spi/dw_spi: move dw_spi.h into drivers/spi
spi/dw_spi: Fix missing header
gpio/langwell: Clear edge bit before handling
gpio/langwell: Simplify demux loop
gpio/langwell: Convert irq name space
gpio/langwell: Fix broken irq_eoi change.
gpio; Make Intel chipset gpio drivers depend on x86
gpio/cs5535-gpio: Fix section mismatch
spi/rtc-{ds1390,ds3234,m41t94}: Use spi_get_drvdata() for SPI devices
spi/davinci: Support DMA transfers larger than 65535 words
spi/davinci: Use correct length parameter to dma_map_single calls
gpio: Use __devexit at necessary places
gpio: add MODULE_DEVICE_TABLE to pch_gpio and ml_ioh_gpio
gpio/mcp23s08: support mcp23s17 variant
of_mmc_spi: add card detect irq support
spi/omap_mcspi: catch xfers of non-multiple SPI word size
spi/omap_mcspi: Off-by-one error in finding the right divisor
gpio/pca953x: Fix wrong pointer type
spi/pl022: rid dangling labels
spi: add support for SuperH SPI
...
include/linux/dw_spi.h only includes driver internal data. It doesn't
expose a platform_data configuration structure or similar (at least
nothing in-tree). This patch moves the header into drivers/spi so
that the scope is limited to only the dw_spi_*.c driver files
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Feng Tang <feng.tang@intel.com>
Cc: spi-devel-general@lists.sourceforge.net
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
* 'defcfg' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6647/1: add Versatile Express defconfig
ARM: 6644/1: mach-ux500: update the U8500 defconfig
* 'drivers' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6764/1: pl011: factor out FIFO to TTY code
ARM: 6763/1: pl011: add optional RX DMA to PL011 v2
ARM: 6758/1: amba: support pm ops
ARM: amba: make amba_driver id_table const
ARM: amba: make internal ID table handling const
ARM: amba: make probe() functions take const id tables
ARM: 6662/1: amba: make amba_bustype non-static
ARM: mmci: add dmaengine-based DMA support
ARM: mmci: no need for separate host->data_xfered
ARM: mmci: avoid unnecessary switch to data available PIO interrupts
ARM: mmci: no need to call flush_dcache_page() with sg_miter API
ARM: mmci: avoid reporting too many completed bytes on fifo overrun
ALSA: AACI: make fifo variables more explanitory
ALSA: AACI: no need to call snd_pcm_period_elapsed() for each period
ALSA: AACI: use snd_pcm_lib_period_bytes()
ALSA: AACI: clean up AACI announcement printk
ALSA: AACI: fix channel mask selection
ALSA: AACI: fix number of channels for record
ALSA: AACI: fix multiple IRQ claiming
* 'cyberpro-next' of master.kernel.org:/home/rmk/linux-2.6-arm:
VIDEO: cyberpro: remove unused cyber2000fb_get_fb_var()
VIDEO: cyberpro: remove useless function extreg pointers
VIDEO: cyberpro: update handling of device structures
VIDEO: cyberpro: add support for video capture I2C
VIDEO: cyberpro: make 'reg_b0_lock' always present
VIDEO: cyberpro: add I2C support
VIDEO: cyberpro: select lowest multipler/divisor for PLL
This patch adds an SPI master implementation that operates on top of an
underlying TI-SSP port.
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The current davinci SPI driver, in DMA mode, is limited to 65535
words for a single transfer. Modify the driver by configuring a
3 dimensional EDMA transfer to support up to 65535x65535
words.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The davinci spi driver provides an option to use DMA transfers for
data. In the dma_map_single() call, the driver is passing the
number of words to be transfered for the mapping size. It should
be the number of bytes.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Move to SOC_SOC_IMX3X.
Leave ARCH_MX31/35 definitions there, in case some place prevent multi-soc
single image.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Shubhrajyoti D